platform/target: msmtitanium: Add Initial platform support for MSMTITANIUM
This patch adds support for the initial IOMAP registers
used in MSMTITANIUM and also basic functionality needed for the
target MSMTITANIUM to boot up
Change-Id: I79323c52c10dd47e71707846cf53ba1e9aed03c8
diff --git a/target/msmtitanium/init.c b/target/msmtitanium/init.c
new file mode 100644
index 0000000..5f76517
--- /dev/null
+++ b/target/msmtitanium/init.c
@@ -0,0 +1,252 @@
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are
+ * met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above
+ * copyright notice, this list of conditions and the following
+ * disclaimer in the documentation and/or other materials provided
+ * with the distribution.
+ * * Neither the name of The Linux Foundation nor the names of its
+ * contributors may be used to endorse or promote products derived
+ * from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT
+ * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS
+ * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
+ * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
+ * OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
+ * IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#include <debug.h>
+#include <platform/iomap.h>
+#include <reg.h>
+#include <target.h>
+#include <platform.h>
+#include <uart_dm.h>
+#include <mmc.h>
+#include <platform/gpio.h>
+#include <dev/keys.h>
+#include <spmi_v2.h>
+#include <pm8x41.h>
+#include <board.h>
+#include <baseband.h>
+#include <hsusb.h>
+#include <scm.h>
+#include <platform/gpio.h>
+#include <platform/gpio.h>
+#include <platform/irqs.h>
+#include <platform/clock.h>
+#include <crypto5_wrapper.h>
+#include <partition_parser.h>
+#include <stdlib.h>
+
+#if LONG_PRESS_POWER_ON
+#include <shutdown_detect.h>
+#endif
+
+#define PMIC_ARB_CHANNEL_NUM 0
+#define PMIC_ARB_OWNER_ID 0
+#define TLMM_VOL_UP_BTN_GPIO 85
+
+#define FASTBOOT_MODE 0x77665500
+#define PON_SOFT_RB_SPARE 0x88F
+
+static uint32_t mmc_sdc_base[] =
+ { MSM_SDC1_BASE, MSM_SDC2_BASE };
+
+
+void target_early_init(void)
+{
+#if WITH_DEBUG_UART
+ uart_dm_init(1, 0, BLSP1_UART1_BASE);
+#endif
+}
+
+void target_mmc_caps(struct mmc_host *host)
+{
+ host->caps.ddr_mode = 0;
+ host->caps.hs200_mode = 0;
+ host->caps.bus_width = MMC_BOOT_BUS_WIDTH_8_BIT;
+ host->caps.hs_clk_rate = MMC_CLK_50MHZ;
+}
+
+/* Return 1 if vol_up pressed */
+static int target_volume_up()
+{
+ uint8_t status = 0;
+
+ gpio_tlmm_config(TLMM_VOL_UP_BTN_GPIO, 0, GPIO_INPUT, GPIO_PULL_UP, GPIO_2MA, GPIO_ENABLE);
+
+ /* Wait for the gpio config to take effect - debounce time */
+ thread_sleep(10);
+
+ /* Get status of GPIO */
+ status = gpio_status(TLMM_VOL_UP_BTN_GPIO);
+
+ /* Active high signal. */
+ return status;
+}
+
+/* Return 1 if vol_down pressed */
+uint32_t target_volume_down()
+{
+ /* Volume down button tied in with PMIC RESIN. */
+ return pm8x41_resin_status();
+}
+
+static void target_keystatus()
+{
+ keys_init();
+
+ if(target_volume_down())
+ keys_post_event(KEY_VOLUMEDOWN, 1);
+
+ if(target_volume_up())
+ keys_post_event(KEY_VOLUMEUP, 1);
+}
+
+/* Configure PMIC and Drop PS_HOLD for shutdown */
+void shutdown_device()
+{
+ dprintf(CRITICAL, "Going down for shutdown.\n");
+
+ /* Configure PMIC for shutdown */
+ pm8x41_reset_configure(PON_PSHOLD_SHUTDOWN);
+
+ /* Drop PS_HOLD for MSM */
+ writel(0x00, MPM2_MPM_PS_HOLD);
+
+ mdelay(5000);
+
+ dprintf(CRITICAL, "shutdown failed\n");
+
+ ASSERT(0);
+}
+
+
+void target_init(void)
+{
+ uint32_t base_addr;
+ uint8_t slot;
+
+ dprintf(INFO, "target_init()\n");
+
+ spmi_init(PMIC_ARB_CHANNEL_NUM, PMIC_ARB_OWNER_ID);
+
+ target_keystatus();
+
+ /* Trying Slot 1*/
+ slot = 1;
+ base_addr = mmc_sdc_base[slot - 1];
+ if (mmc_boot_main(slot, base_addr)) {
+ /* Trying Slot 2 next */
+ slot = 2;
+ base_addr = mmc_sdc_base[slot - 1];
+ if (mmc_boot_main(slot, base_addr)) {
+ dprintf(CRITICAL, "mmc init failed!");
+ ASSERT(0);
+ }
+ }
+#if LONG_PRESS_POWER_ON
+ shutdown_detect();
+#endif
+}
+
+void target_serialno(unsigned char *buf)
+{
+ uint32_t serialno;
+ if (target_is_emmc_boot()) {
+ serialno = mmc_get_psn();
+ snprintf((char *)buf, 13, "%x", serialno);
+ }
+}
+
+unsigned board_machtype(void)
+{
+}
+
+int set_download_mode(enum dload_mode mode)
+{
+ int ret = 0;
+ ret = scm_dload_mode(mode);
+
+ pm8x41_clear_pmic_watchdog();
+
+ return ret;
+}
+
+int emmc_recovery_init(void)
+{
+ return _emmc_recovery_init();
+}
+
+unsigned target_pause_for_battery_charge(void)
+{
+ uint8_t pon_reason = pm8x41_get_pon_reason();
+ uint8_t is_cold_boot = pm8x41_get_is_cold_boot();
+ dprintf(INFO, "%s : pon_reason is %d cold_boot:%d\n", __func__,
+ pon_reason, is_cold_boot);
+ /* In case of fastboot reboot,adb reboot or if we see the power key
+ * pressed we do not want go into charger mode.
+ * fastboot reboot is warm boot with PON hard reset bit not set
+ * adb reboot is a cold boot with PON hard reset bit set
+ */
+ if (is_cold_boot &&
+ (!(pon_reason & HARD_RST)) &&
+ (!(pon_reason & KPDPWR_N)) &&
+ ((pon_reason & USB_CHG) || (pon_reason & DC_CHG) || (pon_reason & CBLPWR_N)))
+ return 1;
+ else
+ return 0;
+}
+
+/* UTMI MUX configuration to connect PHY to SNPS controller:
+ * Configure primary HS phy mux to use UTMI interface
+ * (connected to usb30 controller).
+ */
+static void tcsr_hs_phy_mux_configure(void)
+{
+ uint32_t reg;
+
+ reg = readl(USB2_PHY_SEL);
+
+ writel(reg | 0x1, USB2_PHY_SEL);
+}
+
+/* configure hs phy mux if using dwc controller */
+void target_usb_phy_mux_configure(void)
+{
+ if(!strcmp(target_usb_controller(), "dwc"))
+ {
+ tcsr_hs_phy_mux_configure();
+ }
+}
+
+/* Initialize target specific USB handlers */
+target_usb_iface_t* target_usb30_init()
+{
+ target_usb_iface_t *t_usb_iface;
+
+ t_usb_iface = calloc(1, sizeof(target_usb_iface_t));
+ ASSERT(t_usb_iface);
+
+ t_usb_iface->mux_config = target_usb_phy_mux_configure;
+ //t_usb_iface->clock_init = clock_usb30_init;
+
+ return t_usb_iface;
+}
+
+/* identify the usb controller to be used for the target */
+const char * target_usb_controller()
+{
+ return "dwc";
+}