ARM: OMAP2+: hwmod code/clockdomain data: fix 32K sync timer
Kevin discovered that commit c8d82ff68fb6873691536cf33021977efbf5593c
("ARM: OMAP2/3: hwmod data: Add 32k-sync timer data to hwmod
database") broke CORE idle on OMAP3. This prevents device low power
states.
The root cause is that the 32K sync timer IP block does not support
smart-idle mode[1], and so the hwmod code keeps the IP block in
no-idle mode while it is active. This in turn prevents the WKUP
clockdomain from transitioning to idle. There is a hardcoded sleep
dependency that prevents the CORE_L3 and CORE_CM clockdomains from
transitioning to idle when the WKUP clockdomain is active[2], so the
chip cannot enter any device low power states.
It turns out that there is no need to take the 32k sync timer out of
idle. The IP block itself probably does not have any native idle
handling at all, due to its simplicity. Furthermore, the PRCM will
never request target idle for this IP block while the kernel is
running, due to the sleep dependency that prevents the WKUP
clockdomain from idling while the CORE_L3 clockdomain is active. So
we can safely leave the 32k sync timer in target-force-idle mode, even
while we continue to access it.
This workaround is implemented by defining a new clockdomain flag,
CLKDM_ACTIVE_WITH_MPU, that indicates that the clockdomain is
guaranteed to be active whenever the MPU is inactive. If an IP
block's main functional clock exists inside this clockdomain, and the
IP block does not support smart-idle modes, then the hwmod code will
place the IP block into target force-idle mode even when enabled. The
WKUP clockdomains on OMAP3/4 are marked with this flag. (On OMAP2xxx,
no OCP header existed on the 32k sync timer.) Other clockdomains also
should be marked with this flag, but those changes are deferred until
a later merge window, to create a minimal fix.
Another theoretically clean fix for this problem would be to implement
PM runtime-based control for 32k sync timer accesses. These PM
runtime calls would need to located in a custom clocksource, since the
32k sync timer is currently used as an MMIO clocksource. But in
practice, there would be little benefit to doing so; and there would
be some cost, due to the addition of unnecessary lines of code and the
additional CPU overhead of the PM runtime and hwmod code - unnecessary
in this case.
Another possible fix would have been to modify the pm34xx.c code to
force the IP block idle before entering WFI. But this would not have
been an acceptable approach: we are trying to remove this type of
centralized IP block idle control from the PM code.
This patch is a collaboration between Kevin Hilman <khilman@ti.com>
and Paul Walmsley <paul@pwsan.com>.
Thanks to Vaibhav Hiremath <hvaibhav@ti.com> for providing comments on
an earlier version of this patch. Thanks to Tero Kristo
<t-kristo@ti.com> for identifying a bug in an earlier version of this
patch. Thanks to Benoît Cousson <b-cousson@ti.com> for identifying
some bugs in several versions of this patch and for implementation
comments.
References:
1. Table 16-96 "REG_32KSYNCNT_SYSCONFIG" of the OMAP34xx TRM Rev. ZU
(SWPU223U), available from:
http://www.ti.com/pdfs/wtbu/OMAP34x_ES3.1.x_PUBLIC_TRM_vzU.zip
2. Table 4-72 "Sleep Dependencies" of the OMAP34xx TRM Rev. ZU
(SWPU223U)
3. ibid.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
diff --git a/arch/arm/mach-omap2/clockdomain.h b/arch/arm/mach-omap2/clockdomain.h
index f7b58609..6227e95 100644
--- a/arch/arm/mach-omap2/clockdomain.h
+++ b/arch/arm/mach-omap2/clockdomain.h
@@ -31,12 +31,16 @@
*
* CLKDM_NO_AUTODEPS: Prevent "autodeps" from being added/removed from this
* clockdomain. (Currently, this applies to OMAP3 clockdomains only.)
+ * CLKDM_ACTIVE_WITH_MPU: The PRCM guarantees that this clockdomain is
+ * active whenever the MPU is active. True for interconnects and
+ * the WKUP clockdomains.
*/
#define CLKDM_CAN_FORCE_SLEEP (1 << 0)
#define CLKDM_CAN_FORCE_WAKEUP (1 << 1)
#define CLKDM_CAN_ENABLE_AUTO (1 << 2)
#define CLKDM_CAN_DISABLE_AUTO (1 << 3)
#define CLKDM_NO_AUTODEPS (1 << 4)
+#define CLKDM_ACTIVE_WITH_MPU (1 << 5)
#define CLKDM_CAN_HWSUP (CLKDM_CAN_ENABLE_AUTO | CLKDM_CAN_DISABLE_AUTO)
#define CLKDM_CAN_SWSUP (CLKDM_CAN_FORCE_SLEEP | CLKDM_CAN_FORCE_WAKEUP)
diff --git a/arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.c b/arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.c
index 839145e1..4972219 100644
--- a/arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.c
+++ b/arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.c
@@ -88,4 +88,5 @@
.name = "wkup_clkdm",
.pwrdm = { .name = "wkup_pwrdm" },
.dep_bit = OMAP_EN_WKUP_SHIFT,
+ .flags = CLKDM_ACTIVE_WITH_MPU,
};
diff --git a/arch/arm/mach-omap2/clockdomains44xx_data.c b/arch/arm/mach-omap2/clockdomains44xx_data.c
index c534258..7f2133a 100644
--- a/arch/arm/mach-omap2/clockdomains44xx_data.c
+++ b/arch/arm/mach-omap2/clockdomains44xx_data.c
@@ -381,7 +381,7 @@
.cm_inst = OMAP4430_PRM_WKUP_CM_INST,
.clkdm_offs = OMAP4430_PRM_WKUP_CM_WKUP_CDOFFS,
.dep_bit = OMAP4430_L4WKUP_STATDEP_SHIFT,
- .flags = CLKDM_CAN_HWSUP,
+ .flags = CLKDM_CAN_HWSUP | CLKDM_ACTIVE_WITH_MPU,
};
static struct clockdomain emu_sys_44xx_clkdm = {
diff --git a/arch/arm/mach-omap2/omap_hwmod.c b/arch/arm/mach-omap2/omap_hwmod.c
index 7731936..2d710f5 100644
--- a/arch/arm/mach-omap2/omap_hwmod.c
+++ b/arch/arm/mach-omap2/omap_hwmod.c
@@ -1124,15 +1124,18 @@
* _enable_sysc - try to bring a module out of idle via OCP_SYSCONFIG
* @oh: struct omap_hwmod *
*
- * If module is marked as SWSUP_SIDLE, force the module out of slave
- * idle; otherwise, configure it for smart-idle. If module is marked
- * as SWSUP_MSUSPEND, force the module out of master standby;
- * otherwise, configure it for smart-standby. No return value.
+ * Ensure that the OCP_SYSCONFIG register for the IP block represented
+ * by @oh is set to indicate to the PRCM that the IP block is active.
+ * Usually this means placing the module into smart-idle mode and
+ * smart-standby, but if there is a bug in the automatic idle handling
+ * for the IP block, it may need to be placed into the force-idle or
+ * no-idle variants of these modes. No return value.
*/
static void _enable_sysc(struct omap_hwmod *oh)
{
u8 idlemode, sf;
u32 v;
+ bool clkdm_act;
if (!oh->class->sysc)
return;
@@ -1141,8 +1144,16 @@
sf = oh->class->sysc->sysc_flags;
if (sf & SYSC_HAS_SIDLEMODE) {
- idlemode = (oh->flags & HWMOD_SWSUP_SIDLE) ?
- HWMOD_IDLEMODE_NO : HWMOD_IDLEMODE_SMART;
+ clkdm_act = ((oh->clkdm &&
+ oh->clkdm->flags & CLKDM_ACTIVE_WITH_MPU) ||
+ (oh->_clk && oh->_clk->clkdm &&
+ oh->_clk->clkdm->flags & CLKDM_ACTIVE_WITH_MPU));
+ if (clkdm_act && !(oh->class->sysc->idlemodes &
+ (SIDLE_SMART | SIDLE_SMART_WKUP)))
+ idlemode = HWMOD_IDLEMODE_FORCE;
+ else
+ idlemode = (oh->flags & HWMOD_SWSUP_SIDLE) ?
+ HWMOD_IDLEMODE_NO : HWMOD_IDLEMODE_SMART;
_set_slave_idlemode(oh, idlemode, &v);
}
@@ -1208,8 +1219,13 @@
sf = oh->class->sysc->sysc_flags;
if (sf & SYSC_HAS_SIDLEMODE) {
- idlemode = (oh->flags & HWMOD_SWSUP_SIDLE) ?
- HWMOD_IDLEMODE_FORCE : HWMOD_IDLEMODE_SMART;
+ /* XXX What about HWMOD_IDLEMODE_SMART_WKUP? */
+ if (oh->flags & HWMOD_SWSUP_SIDLE ||
+ !(oh->class->sysc->idlemodes &
+ (SIDLE_SMART | SIDLE_SMART_WKUP)))
+ idlemode = HWMOD_IDLEMODE_FORCE;
+ else
+ idlemode = HWMOD_IDLEMODE_SMART;
_set_slave_idlemode(oh, idlemode, &v);
}