[ARM] 3961/2: AT91: Support for Atmel AT91SAM9261-EK board
This patch adds support for the Atmel AT91SAM9261-EK board.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
diff --git a/arch/arm/mach-at91rm9200/board-sam9261ek.c b/arch/arm/mach-at91rm9200/board-sam9261ek.c
new file mode 100644
index 0000000..30b490d
--- /dev/null
+++ b/arch/arm/mach-at91rm9200/board-sam9261ek.c
@@ -0,0 +1,259 @@
+/*
+ * linux/arch/arm/mach-at91rm9200/board-ek.c
+ *
+ * Copyright (C) 2005 SAN People
+ * Copyright (C) 2006 Atmel
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/dm9000.h>
+
+#include <asm/hardware.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/at91sam926x_mc.h>
+
+#include "generic.h"
+
+
+/*
+ * Serial port configuration.
+ * 0 .. 2 = USART0 .. USART2
+ * 3 = DBGU
+ */
+static struct at91_uart_config __initdata ek_uart_config = {
+ .console_tty = 0, /* ttyS0 */
+ .nr_tty = 1,
+ .tty_map = { 3, -1, -1, -1 } /* ttyS0, ..., ttyS3 */
+};
+
+static void __init ek_map_io(void)
+{
+ /* Initialize processor: 18.432 MHz crystal */
+ at91sam9261_initialize(18432000);
+
+ /* Setup the serial ports and console */
+ at91_init_serial(&ek_uart_config);
+}
+
+static void __init ek_init_irq(void)
+{
+ at91sam9261_init_interrupts(NULL);
+}
+
+
+/*
+ * DM9000 ethernet device
+ */
+#if defined(CONFIG_DM9000)
+static struct resource at91sam9261_dm9000_resource[] = {
+ [0] = {
+ .start = AT91_CHIPSELECT_2,
+ .end = AT91_CHIPSELECT_2 + 3,
+ .flags = IORESOURCE_MEM
+ },
+ [1] = {
+ .start = AT91_CHIPSELECT_2 + 0x44,
+ .end = AT91_CHIPSELECT_2 + 0xFF,
+ .flags = IORESOURCE_MEM
+ },
+ [2] = {
+ .start = AT91_PIN_PC11,
+ .end = AT91_PIN_PC11,
+ .flags = IORESOURCE_IRQ
+ }
+};
+
+static struct dm9000_plat_data dm9000_platdata = {
+ .flags = DM9000_PLATF_16BITONLY,
+};
+
+static struct platform_device at91sam9261_dm9000_device = {
+ .name = "dm9000",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(at91sam9261_dm9000_resource),
+ .resource = at91sam9261_dm9000_resource,
+ .dev = {
+ .platform_data = &dm9000_platdata,
+ }
+};
+
+static void __init ek_add_device_dm9000(void)
+{
+ /*
+ * Configure Chip-Select 2 on SMC for the DM9000.
+ * Note: These timings were calculated for MASTER_CLOCK = 100000000
+ * according to the DM9000 timings.
+ */
+ at91_sys_write(AT91_SMC_SETUP(2), AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(0) | AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(0));
+ at91_sys_write(AT91_SMC_PULSE(2), AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(8) | AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(8));
+ at91_sys_write(AT91_SMC_CYCLE(2), AT91_SMC_NWECYCLE_(16) | AT91_SMC_NRDCYCLE_(16));
+ at91_sys_write(AT91_SMC_MODE(2), AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16 | AT91_SMC_TDF_(1));
+
+ /* Configure Reset signal as output */
+ at91_set_gpio_output(AT91_PIN_PC10, 0);
+
+ /* Configure Interrupt pin as input, no pull-up */
+ at91_set_gpio_input(AT91_PIN_PC11, 0);
+
+ platform_device_register(&at91sam9261_dm9000_device);
+}
+#else
+static void __init ek_add_device_dm9000(void) {}
+#endif /* CONFIG_DM9000 */
+
+
+/*
+ * USB Host Port
+ */
+static struct at91_usbh_data __initdata ek_usbh_data = {
+ .ports = 2,
+};
+
+
+/*
+ * USB Device Port
+ */
+static struct at91_udc_data __initdata ek_udc_data = {
+ .vbus_pin = AT91_PIN_PB29,
+ .pullup_pin = 0, /* pull-up driven by UDC */
+};
+
+
+/*
+ * MCI (SD/MMC)
+ */
+static struct at91_mmc_data __initdata ek_mmc_data = {
+ .wire4 = 1,
+// .det_pin = ... not connected
+// .wp_pin = ... not connected
+// .vcc_pin = ... not connected
+};
+
+
+/*
+ * NAND flash
+ */
+static struct mtd_partition __initdata ek_nand_partition[] = {
+ {
+ .name = "Partition 1",
+ .offset = 0,
+ .size = 256 * 1024,
+ },
+ {
+ .name = "Partition 2",
+ .offset = 256 * 1024 ,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct mtd_partition *nand_partitions(int size, int *num_partitions)
+{
+ *num_partitions = ARRAY_SIZE(ek_nand_partition);
+ return ek_nand_partition;
+}
+
+static struct at91_nand_data __initdata ek_nand_data = {
+ .ale = 22,
+ .cle = 21,
+// .det_pin = ... not connected
+ .rdy_pin = AT91_PIN_PC15,
+ .enable_pin = AT91_PIN_PC14,
+ .partition_info = nand_partitions,
+#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+ .bus_width_16 = 1,
+#else
+ .bus_width_16 = 0,
+#endif
+};
+
+/*
+ * SPI devices
+ */
+static struct spi_board_info ek_spi_devices[] = {
+ { /* DataFlash chip */
+ .modalias = "mtd_dataflash",
+ .chip_select = 0,
+ .max_speed_hz = 15 * 1000 * 1000,
+ .bus_num = 0,
+ },
+#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
+ { /* DataFlash card - jumper (J12) configurable to CS3 or CS0 */
+ .modalias = "mtd_dataflash",
+ .chip_select = 3,
+ .max_speed_hz = 15 * 1000 * 1000,
+ .bus_num = 0,
+ },
+#elif defined(CONFIG_SND_AT73C213)
+ { /* AT73C213 DAC */
+ .modalias = "snd_at73c213",
+ .chip_select = 3,
+ .max_speed_hz = 10 * 1000 * 1000,
+ .bus_num = 0,
+ },
+#endif
+};
+
+
+static void __init ek_board_init(void)
+{
+ /* Serial */
+ at91_add_device_serial();
+ /* USB Host */
+ at91_add_device_usbh(&ek_usbh_data);
+ /* USB Device */
+ at91_add_device_udc(&ek_udc_data);
+ /* I2C */
+ at91_add_device_i2c();
+ /* NAND */
+ at91_add_device_nand(&ek_nand_data);
+ /* DM9000 ethernet */
+ ek_add_device_dm9000();
+
+ /* spi0 and mmc/sd share the same PIO pins */
+#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
+ /* SPI */
+ at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
+#else
+ /* MMC */
+ at91_add_device_mmc(&ek_mmc_data);
+#endif
+}
+
+MACHINE_START(AT91SAM9261EK, "Atmel AT91SAM9261-EK")
+ /* Maintainer: Atmel */
+ .phys_io = AT91_BASE_SYS,
+ .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+ .boot_params = AT91_SDRAM_BASE + 0x100,
+ .timer = &at91sam926x_timer,
+ .map_io = ek_map_io,
+ .init_irq = ek_init_irq,
+ .init_machine = ek_board_init,
+MACHINE_END