| /*****************************************************************************/ |
| |
| /* |
| * head.S -- common startup code for ColdFire CPUs. |
| * |
| * (C) Copyright 1999-2004, Greg Ungerer (gerg@snapgear.com). |
| */ |
| |
| /*****************************************************************************/ |
| |
| #include <linux/config.h> |
| #include <linux/sys.h> |
| #include <linux/linkage.h> |
| #include <asm/asm-offsets.h> |
| #include <asm/coldfire.h> |
| #include <asm/mcfcache.h> |
| #include <asm/mcfsim.h> |
| |
| /*****************************************************************************/ |
| |
| /* |
| * Define fixed memory sizes. Configuration of a fixed memory size |
| * overrides everything else. If the user defined a size we just |
| * blindly use it (they know what they are doing right :-) |
| */ |
| #if defined(CONFIG_RAM32MB) |
| #define MEM_SIZE 0x02000000 /* memory size 32Mb */ |
| #elif defined(CONFIG_RAM16MB) |
| #define MEM_SIZE 0x01000000 /* memory size 16Mb */ |
| #elif defined(CONFIG_RAM8MB) |
| #define MEM_SIZE 0x00800000 /* memory size 8Mb */ |
| #elif defined(CONFIG_RAM4MB) |
| #define MEM_SIZE 0x00400000 /* memory size 4Mb */ |
| #elif defined(CONFIG_RAM1MB) |
| #define MEM_SIZE 0x00100000 /* memory size 1Mb */ |
| #endif |
| |
| /* |
| * Memory size exceptions for special cases. Some boards may be set |
| * for auto memory sizing, but we can't do it that way for some reason. |
| * For example the 5206eLITE board has static RAM, and auto-detecting |
| * the SDRAM will do you no good at all. Same goes for the MOD5272. |
| */ |
| #ifdef CONFIG_RAMAUTO |
| #if defined(CONFIG_M5206eLITE) |
| #define MEM_SIZE 0x00100000 /* 1MiB default memory */ |
| #endif |
| #if defined(CONFIG_MOD5272) |
| #define MEM_SIZE 0x00800000 /* 8MiB default memory */ |
| #endif |
| #endif /* CONFIG_RAMAUTO */ |
| |
| |
| /* |
| * If we don't have a fixed memory size now, then lets build in code |
| * to auto detect the DRAM size. Obviously this is the prefered |
| * method, and should work for most boards (it won't work for those |
| * that do not have their RAM starting at address 0). |
| */ |
| #if defined(MEM_SIZE) |
| .macro GET_MEM_SIZE |
| movel #MEM_SIZE,%d0 /* hard coded memory size */ |
| .endm |
| |
| #elif defined(CONFIG_M5206) || defined(CONFIG_M5206e) || \ |
| defined(CONFIG_M5249) || defined(CONFIG_M527x) || \ |
| defined(CONFIG_M528x) || defined(CONFIG_M5307) || \ |
| defined(CONFIG_M5407) |
| /* |
| * Not all these devices have exactly the same DRAM controller, |
| * but the DCMR register is virtually identical - give or take |
| * a couple of bits. The only exception is the 5272 devices, their |
| * DRAM controller is quite different. |
| */ |
| .macro GET_MEM_SIZE |
| movel MCF_MBAR+MCFSIM_DMR0,%d0 /* get mask for 1st bank */ |
| btst #0,%d0 /* check if region enabled */ |
| beq 1f |
| andl #0xfffc0000,%d0 |
| beq 1f |
| addl #0x00040000,%d0 /* convert mask to size */ |
| 1: |
| movel MCF_MBAR+MCFSIM_DMR1,%d1 /* get mask for 2nd bank */ |
| btst #0,%d1 /* check if region enabled */ |
| beq 2f |
| andl #0xfffc0000, %d1 |
| beq 2f |
| addl #0x00040000,%d1 |
| addl %d1,%d0 /* total mem size in d0 */ |
| 2: |
| .endm |
| |
| #elif defined(CONFIG_M5272) |
| .macro GET_MEM_SIZE |
| movel MCF_MBAR+MCFSIM_CSOR7,%d0 /* get SDRAM address mask */ |
| andil #0xfffff000,%d0 /* mask out chip select options */ |
| negl %d0 /* negate bits */ |
| .endm |
| |
| #else |
| #error "ERROR: I don't know how to determine your boards memory size?" |
| #endif |
| |
| |
| /* |
| * Most ColdFire boards have their DRAM starting at address 0. |
| * Notable exception is the 5206eLITE board, another is the MOD5272. |
| */ |
| #if defined(CONFIG_M5206eLITE) |
| #define MEM_BASE 0x30000000 |
| #endif |
| #if defined(CONFIG_MOD5272) |
| #define MEM_BASE 0x02000000 |
| #define VBR_BASE 0x20000000 /* vectors in SRAM */ |
| #endif |
| |
| #ifndef MEM_BASE |
| #define MEM_BASE 0x00000000 /* memory base at address 0 */ |
| #endif |
| |
| /* |
| * The default location for the vectors is at the base of RAM. |
| * Some boards might like to use internal SRAM or something like |
| * that. If no board specific header defines an alternative then |
| * use the base of RAM. |
| */ |
| #ifndef VBR_BASE |
| #define VBR_BASE MEM_BASE /* vector address */ |
| #endif |
| |
| /*****************************************************************************/ |
| |
| /* |
| * Boards and platforms can do specific early hardware setup if |
| * they need to. Most don't need this, define away if not required. |
| */ |
| #ifndef PLATFORM_SETUP |
| #define PLATFORM_SETUP |
| #endif |
| |
| /*****************************************************************************/ |
| |
| .global _start |
| .global _rambase |
| .global _ramvec |
| .global _ramstart |
| .global _ramend |
| |
| /*****************************************************************************/ |
| |
| .data |
| |
| /* |
| * During startup we store away the RAM setup. These are not in the |
| * bss, since their values are determined and written before the bss |
| * has been cleared. |
| */ |
| _rambase: |
| .long 0 |
| _ramvec: |
| .long 0 |
| _ramstart: |
| .long 0 |
| _ramend: |
| .long 0 |
| |
| /*****************************************************************************/ |
| |
| .text |
| |
| /* |
| * This is the codes first entry point. This is where it all |
| * begins... |
| */ |
| |
| _start: |
| nop /* filler */ |
| movew #0x2700, %sr /* no interrupts */ |
| |
| /* |
| * Do any platform or board specific setup now. Most boards |
| * don't need anything. Those exceptions are define this in |
| * their board specific includes. |
| */ |
| PLATFORM_SETUP |
| |
| /* |
| * Create basic memory configuration. Set VBR accordingly, |
| * and size memory. |
| */ |
| movel #VBR_BASE,%a7 |
| movec %a7,%VBR /* set vectors addr */ |
| movel %a7,_ramvec |
| |
| movel #MEM_BASE,%a7 /* mark the base of RAM */ |
| movel %a7,_rambase |
| |
| GET_MEM_SIZE /* macro code determines size */ |
| addl %a7,%d0 |
| movel %d0,_ramend /* set end ram addr */ |
| |
| /* |
| * Now that we know what the memory is, lets enable cache |
| * and get things moving. This is Coldfire CPU specific. |
| */ |
| CACHE_ENABLE /* enable CPU cache */ |
| |
| |
| #ifdef CONFIG_ROMFS_FS |
| /* |
| * Move ROM filesystem above bss :-) |
| */ |
| lea _sbss,%a0 /* get start of bss */ |
| lea _ebss,%a1 /* set up destination */ |
| movel %a0,%a2 /* copy of bss start */ |
| |
| movel 8(%a0),%d0 /* get size of ROMFS */ |
| addql #8,%d0 /* allow for rounding */ |
| andl #0xfffffffc, %d0 /* whole words */ |
| |
| addl %d0,%a0 /* copy from end */ |
| addl %d0,%a1 /* copy from end */ |
| movel %a1,_ramstart /* set start of ram */ |
| |
| _copy_romfs: |
| movel -(%a0),%d0 /* copy dword */ |
| movel %d0,-(%a1) |
| cmpl %a0,%a2 /* check if at end */ |
| bne _copy_romfs |
| |
| #else /* CONFIG_ROMFS_FS */ |
| lea _ebss,%a1 |
| movel %a1,_ramstart |
| #endif /* CONFIG_ROMFS_FS */ |
| |
| |
| /* |
| * Zero out the bss region. |
| */ |
| lea _sbss,%a0 /* get start of bss */ |
| lea _ebss,%a1 /* get end of bss */ |
| clrl %d0 /* set value */ |
| _clear_bss: |
| movel %d0,(%a0)+ /* clear each word */ |
| cmpl %a0,%a1 /* check if at end */ |
| bne _clear_bss |
| |
| /* |
| * Load the current task pointer and stack. |
| */ |
| lea init_thread_union,%a0 |
| lea THREAD_SIZE(%a0),%sp |
| |
| /* |
| * Assember start up done, start code proper. |
| */ |
| jsr start_kernel /* start Linux kernel */ |
| |
| _exit: |
| jmp _exit /* should never get here */ |
| |
| /*****************************************************************************/ |