[ARM] S3C24XX: GPIO: Change to macros for GPIO numbering
Prepare to remove the large number of S3C2410_GPxn defines
by moving to S3C2410_GPx(n) in arch/arm.
The following perl was used to change the files:
perl -pi~ -e 's/S3C2410_GP([A-Z])([0-9]+)([^_^0-9])/S3C2410_GP\1\(\2\)\3/g'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
diff --git a/arch/arm/mach-s3c2410/h1940-bluetooth.c b/arch/arm/mach-s3c2410/h1940-bluetooth.c
index 9bbea8a..5aabf11 100644
--- a/arch/arm/mach-s3c2410/h1940-bluetooth.c
+++ b/arch/arm/mach-s3c2410/h1940-bluetooth.c
@@ -43,9 +43,9 @@
h1940_latch_control(0, H1940_LATCH_BLUETOOTH_POWER);
/* Reset the chip */
mdelay(10);
- s3c2410_gpio_setpin(S3C2410_GPH1, 1);
+ s3c2410_gpio_setpin(S3C2410_GPH(1), 1);
mdelay(10);
- s3c2410_gpio_setpin(S3C2410_GPH1, 0);
+ s3c2410_gpio_setpin(S3C2410_GPH(1), 0);
state = 1;
}
@@ -54,9 +54,9 @@
led_trigger_event(bt_led_trigger, 0);
#endif
- s3c2410_gpio_setpin(S3C2410_GPH1, 1);
+ s3c2410_gpio_setpin(S3C2410_GPH(1), 1);
mdelay(10);
- s3c2410_gpio_setpin(S3C2410_GPH1, 0);
+ s3c2410_gpio_setpin(S3C2410_GPH(1), 0);
mdelay(10);
h1940_latch_control(H1940_LATCH_BLUETOOTH_POWER, 0);
@@ -89,14 +89,14 @@
static int __init h1940bt_probe(struct platform_device *pdev)
{
/* Configures BT serial port GPIOs */
- s3c2410_gpio_cfgpin(S3C2410_GPH0, S3C2410_GPH0_nCTS0);
- s3c2410_gpio_pullup(S3C2410_GPH0, 1);
- s3c2410_gpio_cfgpin(S3C2410_GPH1, S3C2410_GPIO_OUTPUT);
- s3c2410_gpio_pullup(S3C2410_GPH1, 1);
- s3c2410_gpio_cfgpin(S3C2410_GPH2, S3C2410_GPH2_TXD0);
- s3c2410_gpio_pullup(S3C2410_GPH2, 1);
- s3c2410_gpio_cfgpin(S3C2410_GPH3, S3C2410_GPH3_RXD0);
- s3c2410_gpio_pullup(S3C2410_GPH3, 1);
+ s3c2410_gpio_cfgpin(S3C2410_GPH(0), S3C2410_GPH0_nCTS0);
+ s3c2410_gpio_pullup(S3C2410_GPH(0), 1);
+ s3c2410_gpio_cfgpin(S3C2410_GPH(1), S3C2410_GPIO_OUTPUT);
+ s3c2410_gpio_pullup(S3C2410_GPH(1), 1);
+ s3c2410_gpio_cfgpin(S3C2410_GPH(2), S3C2410_GPH2_TXD0);
+ s3c2410_gpio_pullup(S3C2410_GPH(2), 1);
+ s3c2410_gpio_cfgpin(S3C2410_GPH(3), S3C2410_GPH3_RXD0);
+ s3c2410_gpio_pullup(S3C2410_GPH(3), 1);
#ifdef CONFIG_LEDS_H1940
led_trigger_register_simple("h1940-bluetooth", &bt_led_trigger);