igb: add pci_dev in few spots to clean up use of dev_err/info/warn
This patch relpaces several references to adapter->pdev->dev with just
pdev->dev. This allows for cleanup of several multiline dev_err/info
calls.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/igb/igb_main.c b/drivers/net/igb/igb_main.c
index b2c0c97..264ff00 100644
--- a/drivers/net/igb/igb_main.c
+++ b/drivers/net/igb/igb_main.c
@@ -1173,6 +1173,7 @@
void igb_reset(struct igb_adapter *adapter)
{
+ struct pci_dev *pdev = adapter->pdev;
struct e1000_hw *hw = &adapter->hw;
struct e1000_mac_info *mac = &hw->mac;
struct e1000_fc_info *fc = &hw->fc;
@@ -1275,7 +1276,7 @@
wr32(E1000_WUC, 0);
if (hw->mac.ops.init_hw(hw))
- dev_err(&adapter->pdev->dev, "Hardware Error\n");
+ dev_err(&pdev->dev, "Hardware Error\n");
igb_update_mng_vlan(adapter);
@@ -3704,17 +3705,18 @@
static int igb_change_mtu(struct net_device *netdev, int new_mtu)
{
struct igb_adapter *adapter = netdev_priv(netdev);
+ struct pci_dev *pdev = adapter->pdev;
int max_frame = new_mtu + ETH_HLEN + ETH_FCS_LEN;
u32 rx_buffer_len, i;
if ((max_frame < ETH_ZLEN + ETH_FCS_LEN) ||
(max_frame > MAX_JUMBO_FRAME_SIZE)) {
- dev_err(&adapter->pdev->dev, "Invalid MTU setting\n");
+ dev_err(&pdev->dev, "Invalid MTU setting\n");
return -EINVAL;
}
if (max_frame > MAX_STD_JUMBO_FRAME_SIZE) {
- dev_err(&adapter->pdev->dev, "MTU > 9216 not supported.\n");
+ dev_err(&pdev->dev, "MTU > 9216 not supported.\n");
return -EINVAL;
}
@@ -3739,7 +3741,7 @@
if (netif_running(netdev))
igb_down(adapter);
- dev_info(&adapter->pdev->dev, "changing MTU from %d to %d\n",
+ dev_info(&pdev->dev, "changing MTU from %d to %d\n",
netdev->mtu, new_mtu);
netdev->mtu = new_mtu;
@@ -4053,6 +4055,7 @@
{
struct net_device *netdev = dev_get_drvdata(dev);
struct igb_adapter *adapter = netdev_priv(netdev);
+ struct pci_dev *pdev = adapter->pdev;
struct e1000_hw *hw = &adapter->hw;
unsigned long event = *(unsigned long *)data;
@@ -4061,12 +4064,9 @@
/* if already enabled, don't do it again */
if (adapter->flags & IGB_FLAG_DCA_ENABLED)
break;
- /* Always use CB2 mode, difference is masked
- * in the CB driver. */
- wr32(E1000_DCA_CTRL, E1000_DCA_CTRL_DCA_MODE_CB2);
if (dca_add_requester(dev) == 0) {
adapter->flags |= IGB_FLAG_DCA_ENABLED;
- dev_info(&adapter->pdev->dev, "DCA enabled\n");
+ dev_info(&pdev->dev, "DCA enabled\n");
igb_setup_dca(adapter);
break;
}
@@ -4076,7 +4076,7 @@
/* without this a class_device is left
* hanging around in the sysfs model */
dca_remove_requester(dev);
- dev_info(&adapter->pdev->dev, "DCA disabled\n");
+ dev_info(&pdev->dev, "DCA disabled\n");
adapter->flags &= ~IGB_FLAG_DCA_ENABLED;
wr32(E1000_DCA_CTRL, E1000_DCA_CTRL_DCA_MODE_DISABLE);
}
@@ -4471,7 +4471,7 @@
retval = igb_set_vf_vlan(adapter, msgbuf, vf);
break;
default:
- dev_err(&adapter->pdev->dev, "Unhandled Msg %08x\n", msgbuf[0]);
+ dev_err(&pdev->dev, "Unhandled Msg %08x\n", msgbuf[0]);
retval = -1;
break;
}
@@ -5472,6 +5472,7 @@
int igb_set_spd_dplx(struct igb_adapter *adapter, u16 spddplx)
{
+ struct pci_dev *pdev = adapter->pdev;
struct e1000_mac_info *mac = &adapter->hw.mac;
mac->autoneg = 0;
@@ -5495,8 +5496,7 @@
break;
case SPEED_1000 + DUPLEX_HALF: /* not supported */
default:
- dev_err(&adapter->pdev->dev,
- "Unsupported Speed/Duplex configuration\n");
+ dev_err(&pdev->dev, "Unsupported Speed/Duplex configuration\n");
return -EINVAL;
}
return 0;