Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here are a bunch of small bug fixes for various ARM platforms, nothing
really sticks out this week, most of either fixes bugs in code that
was just added in 4.4, or that has been broken for many years without
anyone noticing.
at91/sama5d2:
- fix sama5de hardware setup of sd/mmc interface
- proper selection of pinctrl drivers. PIO4 is necessary for sama5d2
berlin:
- fix incorrect clock input for SDIO
exynos:
- Fix potential NULL pointer dereference in Exynos PMU driver.
imx:
- Fix vf610 SAI clock configuration bug which is discovered by the
newly added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
ixp4xx:
- fix prototypes for readl/writel functions
ls2080a:
- use little-endian register access for GPIO and SDHCI
omap:
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of when
MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
pxa:
- use PWM lookup table for all ezx machines
s3c24xx:
- Remove incorrect __init annotation from s3c24xx cpufreq driver
structures.
versatile:
- fix PCI IRQ mapping on Versatile PB"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ls2080a/dts: Add little endian property for GPIO IP block
dt-bindings: define little-endian property for QorIQ GPIO
ARM64: dts: ls2080a: fix eSDHC endianness
ARM: dts: vf610: use reset values for L2 cache latencies
ARM: pxa: use PWM lookup table for all machines
ARM: dts: berlin: add 2nd clock for BG2Q sdhci0 and sdhci1
ARM: dts: berlin: correct BG2Q's sdhci2 2nd clock
ARM: dts: am4372: fix clock source for arm twd and global timers
ARM: at91: fix pinctrl driver selection
ARM: at91/dt: add always-on to 1.8V regulator
ARM: dts: vf610: fix clock definition for SAI2
ARM: imx: clk-vf610: fix SAI clock tree
ARM: ixp4xx: fix read{b,w,l} return types
irqchip/versatile-fpga: Fix PCI IRQ mapping on Versatile PB
ARM: OMAP2+: enable REGULATOR_FIXED_VOLTAGE
ARM: dts: add dm816x missing spi DT dma handles
ARM: dts: add dm816x missing #mbox-cells
cpufreq: s3c24xx: Do not mark s3c2410_plls_add as __init
ARM: EXYNOS: Fix potential NULL pointer access in exynos_sys_powerdown_conf
diff --git a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt
index f2455c5..120bc49 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt
@@ -11,6 +11,10 @@
0 = active high
1 = active low
+Optional properties:
+- little-endian : GPIO registers are used as little endian. If not
+ present registers are used as big endian by default.
+
Example:
gpio0: gpio@1100 {
diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi
index d83ff9c..de8791a 100644
--- a/arch/arm/boot/dts/am4372.dtsi
+++ b/arch/arm/boot/dts/am4372.dtsi
@@ -74,7 +74,7 @@
reg = <0x48240200 0x100>;
interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
interrupt-parent = <&gic>;
- clocks = <&dpll_mpu_m2_ck>;
+ clocks = <&mpu_periphclk>;
};
local_timer: timer@48240600 {
@@ -82,7 +82,7 @@
reg = <0x48240600 0x100>;
interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>;
interrupt-parent = <&gic>;
- clocks = <&dpll_mpu_m2_ck>;
+ clocks = <&mpu_periphclk>;
};
l2-cache-controller@48242000 {
diff --git a/arch/arm/boot/dts/am43xx-clocks.dtsi b/arch/arm/boot/dts/am43xx-clocks.dtsi
index cc88728..a38af2b 100644
--- a/arch/arm/boot/dts/am43xx-clocks.dtsi
+++ b/arch/arm/boot/dts/am43xx-clocks.dtsi
@@ -259,6 +259,14 @@
ti,invert-autoidle-bit;
};
+ mpu_periphclk: mpu_periphclk {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&dpll_mpu_m2_ck>;
+ clock-mult = <1>;
+ clock-div = <2>;
+ };
+
dpll_ddr_ck: dpll_ddr_ck {
#clock-cells = <0>;
compatible = "ti,am3-dpll-clock";
diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
index ad6de73..e74df32 100644
--- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
@@ -184,6 +184,7 @@
regulator-name = "VDD_SDHC_1V8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
+ regulator-always-on;
};
};
};
diff --git a/arch/arm/boot/dts/berlin2q.dtsi b/arch/arm/boot/dts/berlin2q.dtsi
index 8ea177f..fb1da99 100644
--- a/arch/arm/boot/dts/berlin2q.dtsi
+++ b/arch/arm/boot/dts/berlin2q.dtsi
@@ -118,7 +118,8 @@
sdhci0: sdhci@ab0000 {
compatible = "mrvl,pxav3-mmc";
reg = <0xab0000 0x200>;
- clocks = <&chip_clk CLKID_SDIO1XIN>;
+ clocks = <&chip_clk CLKID_SDIO1XIN>, <&chip_clk CLKID_SDIO>;
+ clock-names = "io", "core";
interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
@@ -126,7 +127,8 @@
sdhci1: sdhci@ab0800 {
compatible = "mrvl,pxav3-mmc";
reg = <0xab0800 0x200>;
- clocks = <&chip_clk CLKID_SDIO1XIN>;
+ clocks = <&chip_clk CLKID_SDIO1XIN>, <&chip_clk CLKID_SDIO>;
+ clock-names = "io", "core";
interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
@@ -135,7 +137,7 @@
compatible = "mrvl,pxav3-mmc";
reg = <0xab1000 0x200>;
interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&chip_clk CLKID_NFC_ECC>, <&chip_clk CLKID_NFC>;
+ clocks = <&chip_clk CLKID_NFC_ECC>, <&chip_clk CLKID_SDIO>;
clock-names = "io", "core";
status = "disabled";
};
diff --git a/arch/arm/boot/dts/dm816x.dtsi b/arch/arm/boot/dts/dm816x.dtsi
index 3c99cfa..eee636d 100644
--- a/arch/arm/boot/dts/dm816x.dtsi
+++ b/arch/arm/boot/dts/dm816x.dtsi
@@ -218,6 +218,7 @@
reg = <0x480c8000 0x2000>;
interrupts = <77>;
ti,hwmods = "mailbox";
+ #mbox-cells = <1>;
ti,mbox-num-users = <4>;
ti,mbox-num-fifos = <12>;
mbox_dsp: mbox_dsp {
@@ -279,8 +280,11 @@
ti,spi-num-cs = <4>;
ti,hwmods = "mcspi1";
dmas = <&edma 16 &edma 17
- &edma 18 &edma 19>;
- dma-names = "tx0", "rx0", "tx1", "rx1";
+ &edma 18 &edma 19
+ &edma 20 &edma 21
+ &edma 22 &edma 23>;
+ dma-names = "tx0", "rx0", "tx1", "rx1",
+ "tx2", "rx2", "tx3", "rx3";
};
mmc1: mmc@48060000 {
diff --git a/arch/arm/boot/dts/vf610-colibri.dtsi b/arch/arm/boot/dts/vf610-colibri.dtsi
index 19fe045..2d7eab7 100644
--- a/arch/arm/boot/dts/vf610-colibri.dtsi
+++ b/arch/arm/boot/dts/vf610-colibri.dtsi
@@ -18,8 +18,3 @@
reg = <0x80000000 0x10000000>;
};
};
-
-&L2 {
- arm,data-latency = <2 1 2>;
- arm,tag-latency = <3 2 3>;
-};
diff --git a/arch/arm/boot/dts/vf610.dtsi b/arch/arm/boot/dts/vf610.dtsi
index 5f8eb1b..58bc6e4 100644
--- a/arch/arm/boot/dts/vf610.dtsi
+++ b/arch/arm/boot/dts/vf610.dtsi
@@ -19,7 +19,7 @@
reg = <0x40006000 0x1000>;
cache-unified;
cache-level = <2>;
- arm,data-latency = <1 1 1>;
+ arm,data-latency = <3 3 3>;
arm,tag-latency = <2 2 2>;
};
};
diff --git a/arch/arm/boot/dts/vfxxx.dtsi b/arch/arm/boot/dts/vfxxx.dtsi
index 0d5acc2..3cd1b27 100644
--- a/arch/arm/boot/dts/vfxxx.dtsi
+++ b/arch/arm/boot/dts/vfxxx.dtsi
@@ -178,8 +178,10 @@
compatible = "fsl,vf610-sai";
reg = <0x40031000 0x1000>;
interrupts = <86 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks VF610_CLK_SAI2>;
- clock-names = "sai";
+ clocks = <&clks VF610_CLK_SAI2>,
+ <&clks VF610_CLK_SAI2_DIV>,
+ <&clks 0>, <&clks 0>;
+ clock-names = "bus", "mclk1", "mclk2", "mclk3";
dma-names = "tx", "rx";
dmas = <&edma0 0 21>,
<&edma0 0 20>;
diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index 9267300..28656c2 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -4,7 +4,6 @@
select ARCH_REQUIRE_GPIOLIB
select COMMON_CLK_AT91
select PINCTRL
- select PINCTRL_AT91
select SOC_BUS
if ARCH_AT91
@@ -17,6 +16,7 @@
select HAVE_AT91_USB_CLK
select HAVE_AT91_H32MX
select HAVE_AT91_GENERATED_CLK
+ select PINCTRL_AT91PIO4
help
Select this if ou are using one of Atmel's SAMA5D2 family SoC.
@@ -27,6 +27,7 @@
select HAVE_AT91_UTMI
select HAVE_AT91_SMD
select HAVE_AT91_USB_CLK
+ select PINCTRL_AT91
help
Select this if you are using one of Atmel's SAMA5D3 family SoC.
This support covers SAMA5D31, SAMA5D33, SAMA5D34, SAMA5D35, SAMA5D36.
@@ -40,6 +41,7 @@
select HAVE_AT91_SMD
select HAVE_AT91_USB_CLK
select HAVE_AT91_H32MX
+ select PINCTRL_AT91
help
Select this if you are using one of Atmel's SAMA5D4 family SoC.
@@ -50,6 +52,7 @@
select CPU_ARM920T
select HAVE_AT91_USB_CLK
select MIGHT_HAVE_PCI
+ select PINCTRL_AT91
select SOC_SAM_V4_V5
select SRAM if PM
help
@@ -65,6 +68,7 @@
select HAVE_AT91_UTMI
select HAVE_FB_ATMEL
select MEMORY
+ select PINCTRL_AT91
select SOC_SAM_V4_V5
select SRAM if PM
help
diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
index 80e277c..23726fb 100644
--- a/arch/arm/mach-at91/pm.c
+++ b/arch/arm/mach-at91/pm.c
@@ -41,8 +41,10 @@
* implementation should be moved down into the pinctrl driver and get
* called as part of the generic suspend/resume path.
*/
+#ifdef CONFIG_PINCTRL_AT91
extern void at91_pinctrl_gpio_suspend(void);
extern void at91_pinctrl_gpio_resume(void);
+#endif
static struct {
unsigned long uhp_udp_mask;
@@ -151,8 +153,9 @@
static int at91_pm_enter(suspend_state_t state)
{
+#ifdef CONFIG_PINCTRL_AT91
at91_pinctrl_gpio_suspend();
-
+#endif
switch (state) {
/*
* Suspend-to-RAM is like STANDBY plus slow clock mode, so
@@ -192,7 +195,9 @@
error:
target_state = PM_SUSPEND_ON;
+#ifdef CONFIG_PINCTRL_AT91
at91_pinctrl_gpio_resume();
+#endif
return 0;
}
diff --git a/arch/arm/mach-exynos/pmu.c b/arch/arm/mach-exynos/pmu.c
index de68938..c21e41d 100644
--- a/arch/arm/mach-exynos/pmu.c
+++ b/arch/arm/mach-exynos/pmu.c
@@ -748,8 +748,12 @@
void exynos_sys_powerdown_conf(enum sys_powerdown mode)
{
unsigned int i;
+ const struct exynos_pmu_data *pmu_data;
- const struct exynos_pmu_data *pmu_data = pmu_context->pmu_data;
+ if (!pmu_context)
+ return;
+
+ pmu_data = pmu_context->pmu_data;
if (pmu_data->powerdown_conf)
pmu_data->powerdown_conf(mode);
diff --git a/arch/arm/mach-ixp4xx/include/mach/io.h b/arch/arm/mach-ixp4xx/include/mach/io.h
index b024390..7a0c13b 100644
--- a/arch/arm/mach-ixp4xx/include/mach/io.h
+++ b/arch/arm/mach-ixp4xx/include/mach/io.h
@@ -143,7 +143,7 @@
writel(*vaddr++, bus_addr);
}
-static inline unsigned char __indirect_readb(const volatile void __iomem *p)
+static inline u8 __indirect_readb(const volatile void __iomem *p)
{
u32 addr = (u32)p;
u32 n, byte_enables, data;
@@ -166,7 +166,7 @@
*vaddr++ = readb(bus_addr);
}
-static inline unsigned short __indirect_readw(const volatile void __iomem *p)
+static inline u16 __indirect_readw(const volatile void __iomem *p)
{
u32 addr = (u32)p;
u32 n, byte_enables, data;
@@ -189,7 +189,7 @@
*vaddr++ = readw(bus_addr);
}
-static inline unsigned long __indirect_readl(const volatile void __iomem *p)
+static inline u32 __indirect_readl(const volatile void __iomem *p)
{
u32 addr = (__force u32)p;
u32 data;
@@ -350,7 +350,7 @@
((unsigned long)p <= (PIO_MASK + PIO_OFFSET)))
#define ioread8(p) ioread8(p)
-static inline unsigned int ioread8(const void __iomem *addr)
+static inline u8 ioread8(const void __iomem *addr)
{
unsigned long port = (unsigned long __force)addr;
if (__is_io_address(port))
@@ -378,7 +378,7 @@
}
#define ioread16(p) ioread16(p)
-static inline unsigned int ioread16(const void __iomem *addr)
+static inline u16 ioread16(const void __iomem *addr)
{
unsigned long port = (unsigned long __force)addr;
if (__is_io_address(port))
@@ -407,7 +407,7 @@
}
#define ioread32(p) ioread32(p)
-static inline unsigned int ioread32(const void __iomem *addr)
+static inline u32 ioread32(const void __iomem *addr)
{
unsigned long port = (unsigned long __force)addr;
if (__is_io_address(port))
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 5076d3f..4b4371d 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -121,6 +121,7 @@
select NEON if CPU_V7
select PM
select REGULATOR
+ select REGULATOR_FIXED_VOLTAGE
select TWL4030_CORE if ARCH_OMAP3 || ARCH_OMAP4
select TWL4030_POWER if ARCH_OMAP3 || ARCH_OMAP4
select VFP
@@ -201,7 +202,6 @@
depends on ARCH_OMAP3
default y
select OMAP_PACKAGE_CBB
- select REGULATOR_FIXED_VOLTAGE if REGULATOR
config MACH_NOKIA_N810
bool
diff --git a/arch/arm/mach-pxa/ezx.c b/arch/arm/mach-pxa/ezx.c
index 9a9c15b..7c0d561 100644
--- a/arch/arm/mach-pxa/ezx.c
+++ b/arch/arm/mach-pxa/ezx.c
@@ -889,6 +889,7 @@
pxa_set_keypad_info(&e680_keypad_platform_data);
+ pwm_add_table(ezx_pwm_lookup, ARRAY_SIZE(ezx_pwm_lookup));
platform_add_devices(ARRAY_AND_SIZE(ezx_devices));
platform_add_devices(ARRAY_AND_SIZE(e680_devices));
}
@@ -956,6 +957,7 @@
pxa_set_keypad_info(&a1200_keypad_platform_data);
+ pwm_add_table(ezx_pwm_lookup, ARRAY_SIZE(ezx_pwm_lookup));
platform_add_devices(ARRAY_AND_SIZE(ezx_devices));
platform_add_devices(ARRAY_AND_SIZE(a1200_devices));
}
@@ -1148,6 +1150,7 @@
platform_device_register(&a910_camera);
}
+ pwm_add_table(ezx_pwm_lookup, ARRAY_SIZE(ezx_pwm_lookup));
platform_add_devices(ARRAY_AND_SIZE(ezx_devices));
platform_add_devices(ARRAY_AND_SIZE(a910_devices));
}
@@ -1215,6 +1218,7 @@
pxa_set_keypad_info(&e6_keypad_platform_data);
+ pwm_add_table(ezx_pwm_lookup, ARRAY_SIZE(ezx_pwm_lookup));
platform_add_devices(ARRAY_AND_SIZE(ezx_devices));
platform_add_devices(ARRAY_AND_SIZE(e6_devices));
}
@@ -1256,6 +1260,7 @@
pxa_set_keypad_info(&e2_keypad_platform_data);
+ pwm_add_table(ezx_pwm_lookup, ARRAY_SIZE(ezx_pwm_lookup));
platform_add_devices(ARRAY_AND_SIZE(ezx_devices));
platform_add_devices(ARRAY_AND_SIZE(e2_devices));
}
diff --git a/arch/arm/mach-s3c24xx/pll-s3c2440-12000000.c b/arch/arm/mach-s3c24xx/pll-s3c2440-12000000.c
index a19460e..b355fca 100644
--- a/arch/arm/mach-s3c24xx/pll-s3c2440-12000000.c
+++ b/arch/arm/mach-s3c24xx/pll-s3c2440-12000000.c
@@ -20,7 +20,7 @@
#include <plat/cpu.h>
#include <plat/cpu-freq-core.h>
-static struct cpufreq_frequency_table s3c2440_plls_12[] __initdata = {
+static struct cpufreq_frequency_table s3c2440_plls_12[] = {
{ .frequency = 75000000, .driver_data = PLLVAL(0x75, 3, 3), }, /* FVco 600.000000 */
{ .frequency = 80000000, .driver_data = PLLVAL(0x98, 4, 3), }, /* FVco 640.000000 */
{ .frequency = 90000000, .driver_data = PLLVAL(0x70, 2, 3), }, /* FVco 720.000000 */
diff --git a/arch/arm/mach-s3c24xx/pll-s3c2440-16934400.c b/arch/arm/mach-s3c24xx/pll-s3c2440-16934400.c
index 1191b29..be9a248 100644
--- a/arch/arm/mach-s3c24xx/pll-s3c2440-16934400.c
+++ b/arch/arm/mach-s3c24xx/pll-s3c2440-16934400.c
@@ -20,7 +20,7 @@
#include <plat/cpu.h>
#include <plat/cpu-freq-core.h>
-static struct cpufreq_frequency_table s3c2440_plls_169344[] __initdata = {
+static struct cpufreq_frequency_table s3c2440_plls_169344[] = {
{ .frequency = 78019200, .driver_data = PLLVAL(121, 5, 3), }, /* FVco 624.153600 */
{ .frequency = 84067200, .driver_data = PLLVAL(131, 5, 3), }, /* FVco 672.537600 */
{ .frequency = 90115200, .driver_data = PLLVAL(141, 5, 3), }, /* FVco 720.921600 */
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi
index e81cd48..925552e 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi
@@ -269,6 +269,7 @@
clock-frequency = <0>; /* Updated by bootloader */
voltage-ranges = <1800 1800 3300 3300>;
sdhci,auto-cmd12;
+ little-endian;
bus-width = <4>;
};
@@ -277,6 +278,7 @@
reg = <0x0 0x2300000 0x0 0x10000>;
interrupts = <0 36 0x4>; /* Level high type */
gpio-controller;
+ little-endian;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
@@ -287,6 +289,7 @@
reg = <0x0 0x2310000 0x0 0x10000>;
interrupts = <0 36 0x4>; /* Level high type */
gpio-controller;
+ little-endian;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
@@ -297,6 +300,7 @@
reg = <0x0 0x2320000 0x0 0x10000>;
interrupts = <0 37 0x4>; /* Level high type */
gpio-controller;
+ little-endian;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
@@ -307,6 +311,7 @@
reg = <0x0 0x2330000 0x0 0x10000>;
interrupts = <0 37 0x4>; /* Level high type */
gpio-controller;
+ little-endian;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
diff --git a/drivers/clk/imx/clk-vf610.c b/drivers/clk/imx/clk-vf610.c
index d1b1c95..0a94d96 100644
--- a/drivers/clk/imx/clk-vf610.c
+++ b/drivers/clk/imx/clk-vf610.c
@@ -335,22 +335,22 @@
clk[VF610_CLK_SAI0_SEL] = imx_clk_mux("sai0_sel", CCM_CSCMR1, 0, 2, sai_sels, 4);
clk[VF610_CLK_SAI0_EN] = imx_clk_gate("sai0_en", "sai0_sel", CCM_CSCDR1, 16);
clk[VF610_CLK_SAI0_DIV] = imx_clk_divider("sai0_div", "sai0_en", CCM_CSCDR1, 0, 4);
- clk[VF610_CLK_SAI0] = imx_clk_gate2("sai0", "sai0_div", CCM_CCGR0, CCM_CCGRx_CGn(15));
+ clk[VF610_CLK_SAI0] = imx_clk_gate2("sai0", "ipg_bus", CCM_CCGR0, CCM_CCGRx_CGn(15));
clk[VF610_CLK_SAI1_SEL] = imx_clk_mux("sai1_sel", CCM_CSCMR1, 2, 2, sai_sels, 4);
clk[VF610_CLK_SAI1_EN] = imx_clk_gate("sai1_en", "sai1_sel", CCM_CSCDR1, 17);
clk[VF610_CLK_SAI1_DIV] = imx_clk_divider("sai1_div", "sai1_en", CCM_CSCDR1, 4, 4);
- clk[VF610_CLK_SAI1] = imx_clk_gate2("sai1", "sai1_div", CCM_CCGR1, CCM_CCGRx_CGn(0));
+ clk[VF610_CLK_SAI1] = imx_clk_gate2("sai1", "ipg_bus", CCM_CCGR1, CCM_CCGRx_CGn(0));
clk[VF610_CLK_SAI2_SEL] = imx_clk_mux("sai2_sel", CCM_CSCMR1, 4, 2, sai_sels, 4);
clk[VF610_CLK_SAI2_EN] = imx_clk_gate("sai2_en", "sai2_sel", CCM_CSCDR1, 18);
clk[VF610_CLK_SAI2_DIV] = imx_clk_divider("sai2_div", "sai2_en", CCM_CSCDR1, 8, 4);
- clk[VF610_CLK_SAI2] = imx_clk_gate2("sai2", "sai2_div", CCM_CCGR1, CCM_CCGRx_CGn(1));
+ clk[VF610_CLK_SAI2] = imx_clk_gate2("sai2", "ipg_bus", CCM_CCGR1, CCM_CCGRx_CGn(1));
clk[VF610_CLK_SAI3_SEL] = imx_clk_mux("sai3_sel", CCM_CSCMR1, 6, 2, sai_sels, 4);
clk[VF610_CLK_SAI3_EN] = imx_clk_gate("sai3_en", "sai3_sel", CCM_CSCDR1, 19);
clk[VF610_CLK_SAI3_DIV] = imx_clk_divider("sai3_div", "sai3_en", CCM_CSCDR1, 12, 4);
- clk[VF610_CLK_SAI3] = imx_clk_gate2("sai3", "sai3_div", CCM_CCGR1, CCM_CCGRx_CGn(2));
+ clk[VF610_CLK_SAI3] = imx_clk_gate2("sai3", "ipg_bus", CCM_CCGR1, CCM_CCGRx_CGn(2));
clk[VF610_CLK_NFC_SEL] = imx_clk_mux("nfc_sel", CCM_CSCMR1, 12, 2, nfc_sels, 4);
clk[VF610_CLK_NFC_EN] = imx_clk_gate("nfc_en", "nfc_sel", CCM_CSCDR2, 9);
diff --git a/drivers/cpufreq/s3c24xx-cpufreq.c b/drivers/cpufreq/s3c24xx-cpufreq.c
index 733aa51..68ef8fd 100644
--- a/drivers/cpufreq/s3c24xx-cpufreq.c
+++ b/drivers/cpufreq/s3c24xx-cpufreq.c
@@ -648,7 +648,7 @@
*
* Register the given set of PLLs with the system.
*/
-int __init s3c_plltab_register(struct cpufreq_frequency_table *plls,
+int s3c_plltab_register(struct cpufreq_frequency_table *plls,
unsigned int plls_no)
{
struct cpufreq_frequency_table *vals;
diff --git a/drivers/irqchip/irq-versatile-fpga.c b/drivers/irqchip/irq-versatile-fpga.c
index 598ab3f..cadf104 100644
--- a/drivers/irqchip/irq-versatile-fpga.c
+++ b/drivers/irqchip/irq-versatile-fpga.c
@@ -210,7 +210,12 @@
parent_irq = -1;
}
+#ifdef CONFIG_ARCH_VERSATILE
+ fpga_irq_init(base, node->name, IRQ_SIC_START, parent_irq, valid_mask,
+ node);
+#else
fpga_irq_init(base, node->name, 0, parent_irq, valid_mask, node);
+#endif
writel(clear_mask, base + IRQ_ENABLE_CLEAR);
writel(clear_mask, base + FIQ_ENABLE_CLEAR);