ARM: dts: am437x-gp-evm: add LCD data
Add DT data for am437x-gp-evm's LCD panel.
Signed-off-by: Sathya Prakash M R <sathyap@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
diff --git a/arch/arm/boot/dts/am437x-gp-evm.dts b/arch/arm/boot/dts/am437x-gp-evm.dts
index f432685..c16d975 100644
--- a/arch/arm/boot/dts/am437x-gp-evm.dts
+++ b/arch/arm/boot/dts/am437x-gp-evm.dts
@@ -19,6 +19,10 @@
model = "TI AM437x GP EVM";
compatible = "ti,am437x-gp-evm","ti,am4372","ti,am43";
+ aliases {
+ display0 = &lcd0;
+ };
+
vmmcsd_fixed: fixedregulator-sd {
compatible = "regulator-fixed";
regulator-name = "vmmcsd_fixed";
@@ -64,6 +68,44 @@
0x02000069 /* LEFT */
0x0201006c>; /* DOWN */
};
+
+ lcd0: display {
+ compatible = "osddisplays,osd057T0559-34ts", "panel-dpi";
+ label = "lcd";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_pins>;
+
+ /*
+ * SelLCDorHDMI, LOW to select HDMI. This is not really the
+ * panel's enable GPIO, but we don't have HDMI driver support nor
+ * support to switch between two displays, so using this gpio as
+ * panel's enable should be safe.
+ */
+ enable-gpios = <&gpio5 8 GPIO_ACTIVE_HIGH>;
+
+ panel-timing {
+ clock-frequency = <33000000>;
+ hactive = <800>;
+ vactive = <480>;
+ hfront-porch = <210>;
+ hback-porch = <16>;
+ hsync-len = <30>;
+ vback-porch = <10>;
+ vfront-porch = <22>;
+ vsync-len = <13>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ port {
+ lcd_in: endpoint {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+ };
};
&am43xx_pinmux {
@@ -171,6 +213,47 @@
0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */
>;
};
+
+ dss_pins: dss_pins {
+ pinctrl-single,pins = <
+ 0x020 (PIN_OUTPUT_PULLUP | MUX_MODE1) /*gpmc ad 8 -> DSS DATA 23 */
+ 0x024 (PIN_OUTPUT_PULLUP | MUX_MODE1)
+ 0x028 (PIN_OUTPUT_PULLUP | MUX_MODE1)
+ 0x02c (PIN_OUTPUT_PULLUP | MUX_MODE1)
+ 0x030 (PIN_OUTPUT_PULLUP | MUX_MODE1)
+ 0x034 (PIN_OUTPUT_PULLUP | MUX_MODE1)
+ 0x038 (PIN_OUTPUT_PULLUP | MUX_MODE1)
+ 0x03c (PIN_OUTPUT_PULLUP | MUX_MODE1) /*gpmc ad 15 -> DSS DATA 16 */
+ 0x0a0 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS DATA 0 */
+ 0x0a4 (PIN_OUTPUT_PULLUP | MUX_MODE0)
+ 0x0a8 (PIN_OUTPUT_PULLUP | MUX_MODE0)
+ 0x0ac (PIN_OUTPUT_PULLUP | MUX_MODE0)
+ 0x0b0 (PIN_OUTPUT_PULLUP | MUX_MODE0)
+ 0x0b4 (PIN_OUTPUT_PULLUP | MUX_MODE0)
+ 0x0b8 (PIN_OUTPUT_PULLUP | MUX_MODE0)
+ 0x0bc (PIN_OUTPUT_PULLUP | MUX_MODE0)
+ 0x0c0 (PIN_OUTPUT_PULLUP | MUX_MODE0)
+ 0x0c4 (PIN_OUTPUT_PULLUP | MUX_MODE0)
+ 0x0c8 (PIN_OUTPUT_PULLUP | MUX_MODE0)
+ 0x0cc (PIN_OUTPUT_PULLUP | MUX_MODE0)
+ 0x0d0 (PIN_OUTPUT_PULLUP | MUX_MODE0)
+ 0x0d4 (PIN_OUTPUT_PULLUP | MUX_MODE0)
+ 0x0d8 (PIN_OUTPUT_PULLUP | MUX_MODE0)
+ 0x0dc (PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS DATA 15 */
+ 0x0e0 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS VSYNC */
+ 0x0e4 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS HSYNC */
+ 0x0e8 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS PCLK */
+ 0x0ec (PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS AC BIAS EN */
+
+ >;
+ };
+
+ lcd_pins: lcd_pins {
+ pinctrl-single,pins = <
+ /* GPIO 5_8 to select LCD / HDMI */
+ 0x238 (PIN_OUTPUT_PULLUP | MUX_MODE7)
+ >;
+ };
};
&i2c0 {
@@ -354,3 +437,17 @@
};
};
};
+
+&dss {
+ status = "ok";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dss_pins>;
+
+ port {
+ dpi_out: endpoint@0 {
+ remote-endpoint = <&lcd_in>;
+ data-lines = <24>;
+ };
+ };
+};