diff --git a/Documentation/devicetree/bindings/arm/samsung/pmu.txt b/Documentation/devicetree/bindings/arm/samsung/pmu.txt
index b562634..2a4ab04 100644
--- a/Documentation/devicetree/bindings/arm/samsung/pmu.txt
+++ b/Documentation/devicetree/bindings/arm/samsung/pmu.txt
@@ -2,6 +2,7 @@
 
 Properties:
  - compatible : should contain two values. First value must be one from following list:
+		   - "samsung,exynos3250-pmu" - for Exynos3250 SoC,
 		   - "samsung,exynos4210-pmu" - for Exynos4210 SoC,
 		   - "samsung,exynos4212-pmu" - for Exynos4212 SoC,
 		   - "samsung,exynos4412-pmu" - for Exynos4412 SoC,
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 33409a3..cbe223c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -73,11 +73,14 @@
 	exynos5250-arndale.dtb \
 	exynos5250-smdk5250.dtb \
 	exynos5250-snow.dtb \
+	exynos5260-xyref5260.dtb \
+	exynos5410-smdk5410.dtb \
 	exynos5420-arndale-octa.dtb \
 	exynos5420-peach-pit.dtb \
 	exynos5420-smdk5420.dtb \
 	exynos5440-sd5v1.dtb \
-	exynos5440-ssdk5440.dtb
+	exynos5440-ssdk5440.dtb \
+	exynos5800-peach-pi.dtb
 dtb-$(CONFIG_ARCH_HI3xxx) += hi3620-hi4511.dtb
 dtb-$(CONFIG_ARCH_HIGHBANK) += highbank.dtb \
 	ecx-2000.dtb
diff --git a/arch/arm/boot/dts/exynos3250-pinctrl.dtsi b/arch/arm/boot/dts/exynos3250-pinctrl.dtsi
new file mode 100644
index 0000000..47b92c1
--- /dev/null
+++ b/arch/arm/boot/dts/exynos3250-pinctrl.dtsi
@@ -0,0 +1,475 @@
+/*
+ * Samsung's Exynos3250 SoCs pin-mux and pin-config device tree source
+ *
+ * Copyright (c) 2014 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * Samsung's Exynos3250 SoCs pin-mux and pin-config optiosn are listed as device
+ * tree nodes are listed in this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+&pinctrl_0 {
+	gpa0: gpa0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpa1: gpa1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb: gpb {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpc0: gpc0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpc1: gpc1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpd0: gpd0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpd1: gpd1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	uart0_data: uart0-data {
+		samsung,pins = "gpa0-0", "gpa0-1";
+		samsung,pin-function = <0x2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	uart0_fctl: uart0-fctl {
+		samsung,pins = "gpa0-2", "gpa0-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	uart1_data: uart1-data {
+		samsung,pins = "gpa0-4", "gpa0-5";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	uart1_fctl: uart1-fctl {
+		samsung,pins = "gpa0-6", "gpa0-7";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c2_bus: i2c2-bus {
+		samsung,pins = "gpa0-6", "gpa0-7";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <3>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c3_bus: i2c3-bus {
+		samsung,pins = "gpa1-2", "gpa1-3";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <3>;
+		samsung,pin-drv = <0>;
+	};
+
+	spi0_bus: spi0-bus {
+		samsung,pins = "gpb-0", "gpb-2", "gpb-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <3>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c4_bus: i2c4-bus {
+		samsung,pins = "gpb-0", "gpb-1";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <3>;
+		samsung,pin-drv = <0>;
+	};
+
+	spi1_bus: spi1-bus {
+		samsung,pins = "gpb-4", "gpb-6", "gpb-7";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <3>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c5_bus: i2c5-bus {
+		samsung,pins = "gpb-2", "gpb-3";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <3>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2s2_bus: i2s2-bus {
+		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
+				"gpc1-4";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	pcm2_bus: pcm2-bus {
+		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
+				"gpc1-4";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c6_bus: i2c6-bus {
+		samsung,pins = "gpc1-3", "gpc1-4";
+		samsung,pin-function = <4>;
+		samsung,pin-pud = <3>;
+		samsung,pin-drv = <0>;
+	};
+
+	pwm0_out: pwm0-out {
+		samsung,pins = "gpd0-0";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	pwm1_out: pwm1-out {
+		samsung,pins = "gpd0-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c7_bus: i2c7-bus {
+		samsung,pins = "gpd0-2", "gpd0-3";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <3>;
+		samsung,pin-drv = <0>;
+	};
+
+	pwm2_out: pwm2-out {
+		samsung,pins = "gpd0-2";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	pwm3_out: pwm3-out {
+		samsung,pins = "gpd0-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c0_bus: i2c0-bus {
+		samsung,pins = "gpd1-0", "gpd1-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <3>;
+		samsung,pin-drv = <0>;
+	};
+
+	mipi0_clk: mipi0-clk {
+		samsung,pins = "gpd1-0", "gpd1-1";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c1_bus: i2c1-bus {
+		samsung,pins = "gpd1-2", "gpd1-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <3>;
+		samsung,pin-drv = <0>;
+	};
+};
+
+&pinctrl_1 {
+	gpe0: gpe0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpe1: gpe1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpe2: gpe2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpk0: gpk0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpk1: gpk1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpk2: gpk2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpl0: gpl0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpm0: gpm0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpm1: gpm1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpm2: gpm2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpm3: gpm3 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpm4: gpm4 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpx0: gpx0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		interrupt-parent = <&gic>;
+		interrupts = <0 32 0>, <0 33 0>, <0 34 0>, <0 35 0>,
+				<0 36 0>, <0 37 0>, <0 38 0>, <0 39 0>;
+		#interrupt-cells = <2>;
+	};
+
+	gpx1: gpx1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		interrupt-parent = <&gic>;
+		interrupts = <0 40 0>, <0 41 0>, <0 42 0>, <0 43 0>,
+				<0 44 0>, <0 45 0>, <0 46 0>, <0 47 0>;
+		#interrupt-cells = <2>;
+	};
+
+	gpx2: gpx2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpx3: gpx3 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	sd0_clk: sd0-clk {
+		samsung,pins = "gpk0-0";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_cmd: sd0-cmd {
+		samsung,pins = "gpk0-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_cd: sd0-cd {
+		samsung,pins = "gpk0-2";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <3>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_rdqs: sd0-rdqs {
+		samsung,pins = "gpk0-7";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_bus1: sd0-bus-width1 {
+		samsung,pins = "gpk0-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <3>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_bus4: sd0-bus-width4 {
+		samsung,pins = "gpk0-4", "gpk0-5", "gpk0-6";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <3>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_bus8: sd0-bus-width8 {
+		samsung,pins = "gpl0-0", "gpl0-1", "gpl0-2", "gpl0-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <3>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd1_clk: sd1-clk {
+		samsung,pins = "gpk1-0";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd1_cmd: sd1-cmd {
+		samsung,pins = "gpk1-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd1_cd: sd1-cd {
+		samsung,pins = "gpk1-2";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <3>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd1_bus1: sd1-bus-width1 {
+		samsung,pins = "gpk1-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <3>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd1_bus4: sd1-bus-width4 {
+		samsung,pins = "gpk1-4", "gpk1-5", "gpk1-6";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <3>;
+		samsung,pin-drv = <3>;
+	};
+
+	cam_port_b_io: cam-port-b-io {
+		samsung,pins = "gpm0-0", "gpm0-1", "gpm0-2", "gpm0-3",
+				"gpm0-4", "gpm0-5", "gpm0-6", "gpm0-7",
+				"gpm1-0", "gpm1-1", "gpm2-0", "gpm2-1";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <3>;
+		samsung,pin-drv = <0>;
+	};
+
+	cam_port_b_clk_active: cam-port-b-clk-active {
+		samsung,pins = "gpm2-2";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <3>;
+	};
+
+	cam_port_b_clk_idle: cam-port-b-clk-idle {
+		samsung,pins = "gpm2-2";
+		samsung,pin-function = <0>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	fimc_is_i2c0: fimc-is-i2c0 {
+		samsung,pins = "gpm4-0", "gpm4-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	fimc_is_i2c1: fimc-is-i2c1 {
+		samsung,pins = "gpm4-2", "gpm4-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	fimc_is_uart: fimc-is-uart {
+		samsung,pins = "gpm3-5", "gpm3-7";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+};
diff --git a/arch/arm/boot/dts/exynos3250.dtsi b/arch/arm/boot/dts/exynos3250.dtsi
new file mode 100644
index 0000000..3e678fa
--- /dev/null
+++ b/arch/arm/boot/dts/exynos3250.dtsi
@@ -0,0 +1,444 @@
+/*
+ * Samsung's Exynos3250 SoC device tree source
+ *
+ * Copyright (c) 2014 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * Samsung's Exynos3250 SoC device nodes are listed in this file. Exynos3250
+ * based board files can include this file and provide values for board specfic
+ * bindings.
+ *
+ * Note: This file does not include device nodes for all the controllers in
+ * Exynos3250 SoC. As device tree coverage for Exynos3250 increases, additional
+ * nodes can be added to this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "skeleton.dtsi"
+#include <dt-bindings/clock/exynos3250.h>
+
+/ {
+	compatible = "samsung,exynos3250";
+	interrupt-parent = <&gic>;
+
+	aliases {
+		pinctrl0 = &pinctrl_0;
+		pinctrl1 = &pinctrl_1;
+		mshc0 = &mshc_0;
+		mshc1 = &mshc_1;
+		spi0 = &spi_0;
+		spi1 = &spi_1;
+		i2c0 = &i2c_0;
+		i2c1 = &i2c_1;
+		i2c2 = &i2c_2;
+		i2c3 = &i2c_3;
+		i2c4 = &i2c_4;
+		i2c5 = &i2c_5;
+		i2c6 = &i2c_6;
+		i2c7 = &i2c_7;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0>;
+			clock-frequency = <1000000000>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <1>;
+			clock-frequency = <1000000000>;
+		};
+	};
+
+	soc: soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		fixed-rate-clocks {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			xusbxti: clock@0 {
+				compatible = "fixed-clock";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;
+				clock-frequency = <0>;
+				#clock-cells = <0>;
+				clock-output-names = "xusbxti";
+			};
+
+			xxti: clock@1 {
+				compatible = "fixed-clock";
+				reg = <1>;
+				clock-frequency = <0>;
+				#clock-cells = <0>;
+				clock-output-names = "xxti";
+			};
+
+			xtcxo: clock@2 {
+				compatible = "fixed-clock";
+				reg = <2>;
+				clock-frequency = <0>;
+				#clock-cells = <0>;
+				clock-output-names = "xtcxo";
+			};
+		};
+
+		sysram@02020000 {
+			compatible = "mmio-sram";
+			reg = <0x02020000 0x40000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x02020000 0x40000>;
+
+			smp-sysram@0 {
+				compatible = "samsung,exynos4210-sysram";
+				reg = <0x0 0x1000>;
+			};
+
+			smp-sysram@3f000 {
+				compatible = "samsung,exynos4210-sysram-ns";
+				reg = <0x3f000 0x1000>;
+			};
+		};
+
+		chipid@10000000 {
+			compatible = "samsung,exynos4210-chipid";
+			reg = <0x10000000 0x100>;
+		};
+
+		sys_reg: syscon@10010000 {
+			compatible = "samsung,exynos3-sysreg", "syscon";
+			reg = <0x10010000 0x400>;
+		};
+
+		pmu_system_controller: system-controller@10020000 {
+			compatible = "samsung,exynos3250-pmu", "syscon";
+			reg = <0x10020000 0x4000>;
+		};
+
+		pd_cam: cam-power-domain@10023C00 {
+			compatible = "samsung,exynos4210-pd";
+			reg = <0x10023C00 0x20>;
+		};
+
+		pd_mfc: mfc-power-domain@10023C40 {
+			compatible = "samsung,exynos4210-pd";
+			reg = <0x10023C40 0x20>;
+		};
+
+		pd_g3d: g3d-power-domain@10023C60 {
+			compatible = "samsung,exynos4210-pd";
+			reg = <0x10023C60 0x20>;
+		};
+
+		pd_lcd0: lcd0-power-domain@10023C80 {
+			compatible = "samsung,exynos4210-pd";
+			reg = <0x10023C80 0x20>;
+		};
+
+		pd_isp: isp-power-domain@10023CA0 {
+			compatible = "samsung,exynos4210-pd";
+			reg = <0x10023CA0 0x20>;
+		};
+
+		cmu: clock-controller@10030000 {
+			compatible = "samsung,exynos3250-cmu";
+			reg = <0x10030000 0x20000>;
+			#clock-cells = <1>;
+		};
+
+		rtc: rtc@10070000 {
+			compatible = "samsung,s3c6410-rtc";
+			reg = <0x10070000 0x100>;
+			interrupts = <0 73 0>, <0 74 0>;
+			status = "disabled";
+		};
+
+		gic: interrupt-controller@10481000 {
+			compatible = "arm,cortex-a15-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			reg = <0x10481000 0x1000>,
+			      <0x10482000 0x1000>,
+			      <0x10484000 0x2000>,
+			      <0x10486000 0x2000>;
+			interrupts = <1 9 0xf04>;
+		};
+
+		mct@10050000 {
+			compatible = "samsung,exynos4210-mct";
+			reg = <0x10050000 0x800>;
+			interrupts = <0 218 0>, <0 219 0>, <0 220 0>, <0 221 0>,
+				     <0 223 0>, <0 226 0>, <0 227 0>, <0 228 0>;
+			clocks = <&cmu CLK_FIN_PLL>, <&cmu CLK_MCT>;
+			clock-names = "fin_pll", "mct";
+		};
+
+		pinctrl_1: pinctrl@11000000 {
+			compatible = "samsung,exynos3250-pinctrl";
+			reg = <0x11000000 0x1000>;
+			interrupts = <0 225 0>;
+
+			wakeup-interrupt-controller {
+				compatible = "samsung,exynos4210-wakeup-eint";
+				interrupt-parent = <&gic>;
+				interrupts = <0 48 0>;
+			};
+		};
+
+		pinctrl_0: pinctrl@11400000 {
+			compatible = "samsung,exynos3250-pinctrl";
+			reg = <0x11400000 0x1000>;
+			interrupts = <0 240 0>;
+		};
+
+		mshc_0: mshc@12510000 {
+			compatible = "samsung,exynos5250-dw-mshc";
+			reg = <0x12510000 0x1000>;
+			interrupts = <0 142 0>;
+			clocks = <&cmu CLK_SDMMC0>, <&cmu CLK_SCLK_MMC0>;
+			clock-names = "biu", "ciu";
+			fifo-depth = <0x80>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		mshc_1: mshc@12520000 {
+			compatible = "samsung,exynos5250-dw-mshc";
+			reg = <0x12520000 0x1000>;
+			interrupts = <0 143 0>;
+			clocks = <&cmu CLK_SDMMC1>, <&cmu CLK_SCLK_MMC1>;
+			clock-names = "biu", "ciu";
+			fifo-depth = <0x80>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		amba {
+			compatible = "arm,amba-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			interrupt-parent = <&gic>;
+			ranges;
+
+			pdma0: pdma@12680000 {
+				compatible = "arm,pl330", "arm,primecell";
+				reg = <0x12680000 0x1000>;
+				interrupts = <0 138 0>;
+				clocks = <&cmu CLK_PDMA0>;
+				clock-names = "apb_pclk";
+				#dma-cells = <1>;
+				#dma-channels = <8>;
+				#dma-requests = <32>;
+			};
+
+			pdma1: pdma@12690000 {
+				compatible = "arm,pl330", "arm,primecell";
+				reg = <0x12690000 0x1000>;
+				interrupts = <0 139 0>;
+				clocks = <&cmu CLK_PDMA1>;
+				clock-names = "apb_pclk";
+				#dma-cells = <1>;
+				#dma-channels = <8>;
+				#dma-requests = <32>;
+			};
+		};
+
+		adc: adc@126C0000 {
+			compatible = "samsung,exynos-adc-v3";
+			reg = <0x126C0000 0x100>, <0x10020718 0x4>;
+			interrupts = <0 137 0>;
+			clock-names = "adc", "sclk_tsadc";
+			clocks = <&cmu CLK_TSADC>, <&cmu CLK_SCLK_TSADC>;
+			#io-channel-cells = <1>;
+			io-channel-ranges;
+			status = "disabled";
+		};
+
+		serial_0: serial@13800000 {
+			compatible = "samsung,exynos4210-uart";
+			reg = <0x13800000 0x100>;
+			interrupts = <0 109 0>;
+			clocks = <&cmu CLK_UART0>, <&cmu CLK_SCLK_UART0>;
+			clock-names = "uart", "clk_uart_baud0";
+			status = "disabled";
+		};
+
+		serial_1: serial@13810000 {
+			compatible = "samsung,exynos4210-uart";
+			reg = <0x13810000 0x100>;
+			interrupts = <0 110 0>;
+			clocks = <&cmu CLK_UART1>, <&cmu CLK_SCLK_UART1>;
+			clock-names = "uart", "clk_uart_baud0";
+			status = "disabled";
+		};
+
+		i2c_0: i2c@13860000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "samsung,s3c2440-i2c";
+			reg = <0x13860000 0x100>;
+			interrupts = <0 113 0>;
+			clocks = <&cmu CLK_I2C0>;
+			clock-names = "i2c";
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c0_bus>;
+			status = "disabled";
+		};
+
+		i2c_1: i2c@13870000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "samsung,s3c2440-i2c";
+			reg = <0x13870000 0x100>;
+			interrupts = <0 114 0>;
+			clocks = <&cmu CLK_I2C1>;
+			clock-names = "i2c";
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c1_bus>;
+			status = "disabled";
+		};
+
+		i2c_2: i2c@13880000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "samsung,s3c2440-i2c";
+			reg = <0x13880000 0x100>;
+			interrupts = <0 115 0>;
+			clocks = <&cmu CLK_I2C2>;
+			clock-names = "i2c";
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c2_bus>;
+			status = "disabled";
+		};
+
+		i2c_3: i2c@13890000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "samsung,s3c2440-i2c";
+			reg = <0x13890000 0x100>;
+			interrupts = <0 116 0>;
+			clocks = <&cmu CLK_I2C3>;
+			clock-names = "i2c";
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c3_bus>;
+			status = "disabled";
+		};
+
+		i2c_4: i2c@138A0000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "samsung,s3c2440-i2c";
+			reg = <0x138A0000 0x100>;
+			interrupts = <0 117 0>;
+			clocks = <&cmu CLK_I2C4>;
+			clock-names = "i2c";
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c4_bus>;
+			status = "disabled";
+		};
+
+		i2c_5: i2c@138B0000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "samsung,s3c2440-i2c";
+			reg = <0x138B0000 0x100>;
+			interrupts = <0 118 0>;
+			clocks = <&cmu CLK_I2C5>;
+			clock-names = "i2c";
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c5_bus>;
+			status = "disabled";
+		};
+
+		i2c_6: i2c@138C0000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "samsung,s3c2440-i2c";
+			reg = <0x138C0000 0x100>;
+			interrupts = <0 119 0>;
+			clocks = <&cmu CLK_I2C6>;
+			clock-names = "i2c";
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c6_bus>;
+			status = "disabled";
+		};
+
+		i2c_7: i2c@138D0000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "samsung,s3c2440-i2c";
+			reg = <0x138D0000 0x100>;
+			interrupts = <0 120 0>;
+			clocks = <&cmu CLK_I2C7>;
+			clock-names = "i2c";
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c7_bus>;
+			status = "disabled";
+		};
+
+		spi_0: spi@13920000 {
+			compatible = "samsung,exynos4210-spi";
+			reg = <0x13920000 0x100>;
+			interrupts = <0 121 0>;
+			dmas = <&pdma0 7>, <&pdma0 6>;
+			dma-names = "tx", "rx";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&cmu CLK_SPI0>, <&cmu CLK_SCLK_SPI0>;
+			clock-names = "spi", "spi_busclk0";
+			samsung,spi-src-clk = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi0_bus>;
+			status = "disabled";
+		};
+
+		spi_1: spi@13930000 {
+			compatible = "samsung,exynos4210-spi";
+			reg = <0x13930000 0x100>;
+			interrupts = <0 122 0>;
+			dmas = <&pdma1 7>, <&pdma1 6>;
+			dma-names = "tx", "rx";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&cmu CLK_SPI1>, <&cmu CLK_SCLK_SPI1>;
+			clock-names = "spi", "spi_busclk0";
+			samsung,spi-src-clk = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi1_bus>;
+			status = "disabled";
+		};
+
+		pwm: pwm@139D0000 {
+			compatible = "samsung,exynos4210-pwm";
+			reg = <0x139D0000 0x1000>;
+			interrupts = <0 104 0>, <0 105 0>, <0 106 0>,
+				     <0 107 0>, <0 108 0>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
+		pmu {
+			compatible = "arm,cortex-a7-pmu";
+			interrupts = <0 18 0>, <0 19 0>;
+		};
+	};
+};
+
+#include "exynos3250-pinctrl.dtsi"
diff --git a/arch/arm/boot/dts/exynos4210-origen.dts b/arch/arm/boot/dts/exynos4210-origen.dts
index 72fb11f..f767c42 100644
--- a/arch/arm/boot/dts/exynos4210-origen.dts
+++ b/arch/arm/boot/dts/exynos4210-origen.dts
@@ -16,6 +16,7 @@
 
 /dts-v1/;
 #include "exynos4210.dtsi"
+#include <dt-bindings/input/input.h>
 
 / {
 	model = "Insignal Origen evaluation board based on Exynos4210";
@@ -48,6 +49,14 @@
 		};
 	};
 
+	watchdog@10060000 {
+		status = "okay";
+	};
+
+	rtc@10070000 {
+		status = "okay";
+	};
+
 	tmu@100C0000 {
 		status = "okay";
 	};
@@ -251,35 +260,35 @@
 		up {
 			label = "Up";
 			gpios = <&gpx2 0 1>;
-			linux,code = <103>;
+			linux,code = <KEY_UP>;
 			gpio-key,wakeup;
 		};
 
 		down {
 			label = "Down";
 			gpios = <&gpx2 1 1>;
-			linux,code = <108>;
+			linux,code = <KEY_DOWN>;
 			gpio-key,wakeup;
 		};
 
 		back {
 			label = "Back";
 			gpios = <&gpx1 7 1>;
-			linux,code = <158>;
+			linux,code = <KEY_BACK>;
 			gpio-key,wakeup;
 		};
 
 		home {
 			label = "Home";
 			gpios = <&gpx1 6 1>;
-			linux,code = <102>;
+			linux,code = <KEY_HOME>;
 			gpio-key,wakeup;
 		};
 
 		menu {
 			label = "Menu";
 			gpios = <&gpx1 5 1>;
-			linux,code = <139>;
+			linux,code = <KEY_MENU>;
 			gpio-key,wakeup;
 		};
 	};
diff --git a/arch/arm/boot/dts/exynos4412-origen.dts b/arch/arm/boot/dts/exynos4412-origen.dts
index e2c0dca..e925c9f 100644
--- a/arch/arm/boot/dts/exynos4412-origen.dts
+++ b/arch/arm/boot/dts/exynos4412-origen.dts
@@ -14,6 +14,7 @@
 
 /dts-v1/;
 #include "exynos4412.dtsi"
+#include <dt-bindings/input/input.h>
 
 / {
 	model = "Insignal Origen evaluation board based on Exynos4412";
@@ -48,6 +49,14 @@
 		};
 	};
 
+	watchdog@10060000 {
+		status = "okay";
+	};
+
+	rtc@10070000 {
+		status = "okay";
+	};
+
 	pinctrl@11000000 {
 		keypad_rows: keypad-rows {
 			samsung,pins = "gpx2-0", "gpx2-1", "gpx2-2";
@@ -76,37 +85,37 @@
 		key_home {
 			keypad,row = <0>;
 			keypad,column = <0>;
-			linux,code = <102>;
+			linux,code = <KEY_HOME>;
 		};
 
 		key_down {
 			keypad,row = <0>;
 			keypad,column = <1>;
-			linux,code = <108>;
+			linux,code = <KEY_DOWN>;
 		};
 
 		key_up {
 			keypad,row = <1>;
 			keypad,column = <0>;
-			linux,code = <103>;
+			linux,code = <KEY_UP>;
 		};
 
 		key_menu {
 			keypad,row = <1>;
 			keypad,column = <1>;
-			linux,code = <139>;
+			linux,code = <KEY_MENU>;
 		};
 
 		key_back {
 			keypad,row = <2>;
 			keypad,column = <0>;
-			linux,code = <158>;
+			linux,code = <KEY_BACK>;
 		};
 
 		key_enter {
 			keypad,row = <2>;
 			keypad,column = <1>;
-			linux,code = <28>;
+			linux,code = <KEY_ENTER>;
 		};
 	};
 
diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
index 090f983..1f5afb3 100644
--- a/arch/arm/boot/dts/exynos5250-arndale.dts
+++ b/arch/arm/boot/dts/exynos5250-arndale.dts
@@ -12,6 +12,7 @@
 /dts-v1/;
 #include "exynos5250.dtsi"
 #include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/input/input.h>
 
 / {
 	model = "Insignal Arndale evaluation board based on EXYNOS5250";
@@ -444,42 +445,42 @@
 		menu {
 			label = "SW-TACT2";
 			gpios = <&gpx1 4 1>;
-			linux,code = <139>;
+			linux,code = <KEY_MENU>;
 			gpio-key,wakeup;
 		};
 
 		home {
 			label = "SW-TACT3";
 			gpios = <&gpx1 5 1>;
-			linux,code = <102>;
+			linux,code = <KEY_HOME>;
 			gpio-key,wakeup;
 		};
 
 		up {
 			label = "SW-TACT4";
 			gpios = <&gpx1 6 1>;
-			linux,code = <103>;
+			linux,code = <KEY_UP>;
 			gpio-key,wakeup;
 		};
 
 		down {
 			label = "SW-TACT5";
 			gpios = <&gpx1 7 1>;
-			linux,code = <108>;
+			linux,code = <KEY_DOWN>;
 			gpio-key,wakeup;
 		};
 
 		back {
 			label = "SW-TACT6";
 			gpios = <&gpx2 0 1>;
-			linux,code = <158>;
+			linux,code = <KEY_BACK>;
 			gpio-key,wakeup;
 		};
 
 		wakeup {
 			label = "SW-TACT7";
 			gpios = <&gpx2 1 1>;
-			linux,code = <143>;
+			linux,code = <KEY_WAKEUP>;
 			gpio-key,wakeup;
 		};
 	};
diff --git a/arch/arm/boot/dts/exynos5260-pinctrl.dtsi b/arch/arm/boot/dts/exynos5260-pinctrl.dtsi
new file mode 100644
index 0000000..f6ee55e
--- /dev/null
+++ b/arch/arm/boot/dts/exynos5260-pinctrl.dtsi
@@ -0,0 +1,574 @@
+/*
+ * Samsung's Exynos5260 SoC pin-mux and pin-config device tree source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * Samsung's Exynos5260 SoC pin-mux and pin-config options are listed as device
+ * tree nodes are listed in this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#define PIN_PULL_NONE	0
+#define PIN_PULL_DOWN	1
+#define PIN_PULL_UP	3
+
+&pinctrl_0 {
+	gpa0: gpa0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpa1: gpa1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpa2: gpa2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb0: gpb0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb1: gpb1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb2: gpb2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb3: gpb3 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb4: gpb4 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb5: gpb5 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpd0: gpd0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpd1: gpd1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpd2: gpd2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpe0: gpe0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpe1: gpe1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf0: gpf0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf1: gpf1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpk0: gpk0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpx0: gpx0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpx1: gpx1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpx2: gpx2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpx3: gpx3 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	uart0_data: uart0-data {
+		samsung,pins = "gpa0-0", "gpa0-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	uart0_fctl: uart0-fctl {
+		samsung,pins = "gpa0-2", "gpa0-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	uart1_data: uart1-data {
+		samsung,pins = "gpa1-0", "gpa1-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	uart1_fctl: uart1-fctl {
+		samsung,pins = "gpa1-2", "gpa1-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	uart2_data: uart2-data {
+		samsung,pins = "gpa1-4", "gpa1-5";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	spi0_bus: spi0-bus {
+		samsung,pins = "gpa2-0", "gpa2-2", "gpa2-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	spi1_bus: spi1-bus {
+		samsung,pins = "gpa2-4", "gpa2-6", "gpa2-7";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	usb3_vbus0_en: usb3-vbus0-en {
+		samsung,pins = "gpa2-4";
+		samsung,pin-function = <1>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2s1_bus: i2s1-bus {
+		samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3",
+				"gpb0-4";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	pcm1_bus: pcm1-bus {
+		samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3",
+				"gpb0-4";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	spdif1_bus: spdif1-bus {
+		samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2";
+		samsung,pin-function = <4>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	spi2_bus: spi2-bus {
+		samsung,pins = "gpb1-0", "gpb1-2", "gpb1-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c0_hs_bus: i2c0-hs-bus {
+		samsung,pins = "gpb3-0", "gpb3-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c1_hs_bus: i2c1-hs-bus {
+		samsung,pins = "gpb3-2", "gpb3-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c2_hs_bus: i2c2-hs-bus {
+		samsung,pins = "gpb3-4", "gpb3-5";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c3_hs_bus: i2c3-hs-bus {
+		samsung,pins = "gpb3-6", "gpb3-7";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c4_bus: i2c4-bus {
+		samsung,pins = "gpb4-0", "gpb4-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c5_bus: i2c5-bus {
+		samsung,pins = "gpb4-2", "gpb4-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c6_bus: i2c6-bus {
+		samsung,pins = "gpb4-4", "gpb4-5";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c7_bus: i2c7-bus {
+		samsung,pins = "gpb4-6", "gpb4-7";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c8_bus: i2c8-bus {
+		samsung,pins = "gpb5-0", "gpb5-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c9_bus: i2c9-bus {
+		samsung,pins = "gpb5-2", "gpb5-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c10_bus: i2c10-bus {
+		samsung,pins = "gpb5-4", "gpb5-5";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c11_bus: i2c11-bus {
+		samsung,pins = "gpb5-6", "gpb5-7";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	cam_gpio_a: cam-gpio-a {
+		samsung,pins = "gpe0-0", "gpe0-1", "gpe0-2", "gpe0-3",
+			"gpe0-4", "gpe0-5", "gpe0-6", "gpe0-7",
+			"gpe1-0", "gpe1-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	cam_gpio_b: cam-gpio-b {
+		samsung,pins = "gpf0-0", "gpf0-1", "gpf0-2", "gpf0-3",
+			"gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	cam_i2c1_bus: cam-i2c1-bus {
+		samsung,pins = "gpf0-2", "gpf0-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	cam_i2c0_bus: cam-i2c0-bus {
+		samsung,pins = "gpf0-0", "gpf0-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	cam_spi0_bus: cam-spi0-bus {
+		samsung,pins = "gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	cam_spi1_bus: cam-spi1-bus {
+		samsung,pins = "gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+};
+
+&pinctrl_1 {
+	gpc0: gpc0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpc1: gpc1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpc2: gpc2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpc3: gpc3 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpc4: gpc4 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	sd0_clk: sd0-clk {
+		samsung,pins = "gpc0-0";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_cmd: sd0-cmd {
+		samsung,pins = "gpc0-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_bus1: sd0-bus-width1 {
+		samsung,pins = "gpc0-2";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_bus4: sd0-bus-width4 {
+		samsung,pins = "gpc0-3", "gpc0-4", "gpc0-5";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_bus8: sd0-bus-width8 {
+		samsung,pins = "gpc3-0", "gpc3-1", "gpc3-2", "gpc3-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_rdqs: sd0-rdqs {
+		samsung,pins = "gpc0-6";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd1_clk: sd1-clk {
+		samsung,pins = "gpc1-0";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd1_cmd: sd1-cmd {
+		samsung,pins = "gpc1-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd1_bus1: sd1-bus-width1 {
+		samsung,pins = "gpc1-2";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd1_bus4: sd1-bus-width4 {
+		samsung,pins = "gpc1-3", "gpc1-4", "gpc1-5";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd1_bus8: sd1-bus-width8 {
+		samsung,pins = "gpc4-0", "gpc4-1", "gpc4-2", "gpc4-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd2_clk: sd2-clk {
+		samsung,pins = "gpc2-0";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd2_cmd: sd2-cmd {
+		samsung,pins = "gpc2-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_NONE>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd2_cd: sd2-cd {
+		samsung,pins = "gpc2-2";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd2_bus1: sd2-bus-width1 {
+		samsung,pins = "gpc2-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd2_bus4: sd2-bus-width4 {
+		samsung,pins = "gpc2-4", "gpc2-5", "gpc2-6";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+};
+
+&pinctrl_2 {
+	gpz0: gpz0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpz1: gpz1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+};
diff --git a/arch/arm/boot/dts/exynos5260-xyref5260.dts b/arch/arm/boot/dts/exynos5260-xyref5260.dts
new file mode 100644
index 0000000..8c84ab2
--- /dev/null
+++ b/arch/arm/boot/dts/exynos5260-xyref5260.dts
@@ -0,0 +1,103 @@
+/*
+ * SAMSUNG XYREF5260 board device tree source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/dts-v1/;
+#include "exynos5260.dtsi"
+
+/ {
+	model = "SAMSUNG XYREF5260 board based on EXYNOS5260";
+	compatible = "samsung,xyref5260", "samsung,exynos5260", "samsung,exynos5";
+
+	memory {
+		reg = <0x20000000 0x80000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttySAC2,115200";
+	};
+
+	fin_pll: xxti {
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		clock-output-names = "fin_pll";
+		#clock-cells = <0>;
+	};
+
+	xrtcxti: xrtcxti {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		clock-output-names = "xrtcxti";
+		#clock-cells = <0>;
+	};
+};
+
+&pinctrl_0 {
+	hdmi_hpd_irq: hdmi-hpd-irq {
+		samsung,pins = "gpx3-7";
+		samsung,pin-function = <0>;
+		samsung,pin-pud = <1>;
+		samsung,pin-drv = <0>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&mmc_0 {
+	status = "okay";
+	num-slots = <1>;
+	broken-cd;
+	bypass-smu;
+	supports-highspeed;
+	supports-hs200-mode; /* 200 Mhz */
+	card-detect-delay = <200>;
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-sdr-timing = <0 4>;
+	samsung,dw-mshc-ddr-timing = <0 2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd0_rdqs &sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>;
+
+	slot@0 {
+		reg = <0>;
+		bus-width = <8>;
+	};
+};
+
+&mmc_2 {
+	status = "okay";
+	num-slots = <1>;
+	supports-highspeed;
+	card-detect-delay = <200>;
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-sdr-timing = <2 3>;
+	samsung,dw-mshc-ddr-timing = <1 2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>;
+
+	slot@0 {
+		reg = <0>;
+		bus-width = <4>;
+		disable-wp;
+	};
+};
diff --git a/arch/arm/boot/dts/exynos5260.dtsi b/arch/arm/boot/dts/exynos5260.dtsi
new file mode 100644
index 0000000..5398a60
--- /dev/null
+++ b/arch/arm/boot/dts/exynos5260.dtsi
@@ -0,0 +1,304 @@
+/*
+ * SAMSUNG EXYNOS5260 SoC device tree source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include "skeleton.dtsi"
+
+#include <dt-bindings/clock/exynos5260-clk.h>
+
+/ {
+	compatible = "samsung,exynos5260", "samsung,exynos5";
+	interrupt-parent = <&gic>;
+
+	aliases {
+		pinctrl0 = &pinctrl_0;
+		pinctrl1 = &pinctrl_1;
+		pinctrl2 = &pinctrl_2;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <0x0>;
+			cci-control-port = <&cci_control1>;
+		};
+
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <0x1>;
+			cci-control-port = <&cci_control1>;
+		};
+
+		cpu@100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x100>;
+			cci-control-port = <&cci_control0>;
+		};
+
+		cpu@101 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x101>;
+			cci-control-port = <&cci_control0>;
+		};
+
+		cpu@102 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x102>;
+			cci-control-port = <&cci_control0>;
+		};
+
+		cpu@103 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x103>;
+			cci-control-port = <&cci_control0>;
+		};
+	};
+
+	soc: soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		clock_top: clock-controller@10010000 {
+			compatible = "samsung,exynos5260-clock-top";
+			reg = <0x10010000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_peri: clock-controller@10200000 {
+			compatible = "samsung,exynos5260-clock-peri";
+			reg = <0x10200000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_egl: clock-controller@10600000 {
+			compatible = "samsung,exynos5260-clock-egl";
+			reg = <0x10600000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_kfc: clock-controller@10700000 {
+			compatible = "samsung,exynos5260-clock-kfc";
+			reg = <0x10700000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_g2d: clock-controller@10A00000 {
+			compatible = "samsung,exynos5260-clock-g2d";
+			reg = <0x10A00000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_mif: clock-controller@10CE0000 {
+			compatible = "samsung,exynos5260-clock-mif";
+			reg = <0x10CE0000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_mfc: clock-controller@11090000 {
+			compatible = "samsung,exynos5260-clock-mfc";
+			reg = <0x11090000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_g3d: clock-controller@11830000 {
+			compatible = "samsung,exynos5260-clock-g3d";
+			reg = <0x11830000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_fsys: clock-controller@122E0000 {
+			compatible = "samsung,exynos5260-clock-fsys";
+			reg = <0x122E0000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_aud: clock-controller@128C0000 {
+			compatible = "samsung,exynos5260-clock-aud";
+			reg = <0x128C0000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_isp: clock-controller@133C0000 {
+			compatible = "samsung,exynos5260-clock-isp";
+			reg = <0x133C0000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_gscl: clock-controller@13F00000 {
+			compatible = "samsung,exynos5260-clock-gscl";
+			reg = <0x13F00000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		clock_disp: clock-controller@14550000 {
+			compatible = "samsung,exynos5260-clock-disp";
+			reg = <0x14550000 0x10000>;
+			#clock-cells = <1>;
+		};
+
+		gic: interrupt-controller@10481000 {
+			compatible = "arm,cortex-a15-gic", "arm,cortex-a9-gic";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			#size-cells = <0>;
+			interrupt-controller;
+			reg = <0x10481000 0x1000>,
+				<0x10482000 0x1000>,
+				<0x10484000 0x2000>,
+				<0x10486000 0x2000>;
+			interrupts = <1 9 0xf04>;
+		};
+
+		chipid: chipid@10000000 {
+			compatible = "samsung,exynos4210-chipid";
+			reg = <0x10000000 0x100>;
+		};
+
+		mct: mct@100B0000 {
+			compatible = "samsung,exynos4210-mct";
+			reg = <0x100B0000 0x1000>;
+			clocks = <&fin_pll>, <&clock_peri PERI_CLK_MCT>;
+			clock-names = "fin_pll", "mct";
+			interrupts = <0 104 0>, <0 105 0>, <0 106 0>,
+					<0 107 0>, <0 122 0>, <0 123 0>,
+					<0 124 0>, <0 125 0>, <0 126 0>,
+					<0 127 0>, <0 128 0>, <0 129 0>;
+		};
+
+		cci: cci@10F00000 {
+			compatible = "arm,cci-400";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x10F00000 0x1000>;
+			ranges = <0x0 0x10F00000 0x6000>;
+
+			cci_control0: slave-if@4000 {
+				compatible = "arm,cci-400-ctrl-if";
+				interface-type = "ace";
+				reg = <0x4000 0x1000>;
+			};
+
+			cci_control1: slave-if@5000 {
+				compatible = "arm,cci-400-ctrl-if";
+				interface-type = "ace";
+				reg = <0x5000 0x1000>;
+			};
+		};
+
+		pinctrl_0: pinctrl@11600000 {
+			compatible = "samsung,exynos5260-pinctrl";
+			reg = <0x11600000 0x1000>;
+			interrupts = <0 79 0>;
+
+			wakeup-interrupt-controller {
+				compatible = "samsung,exynos4210-wakeup-eint";
+				interrupt-parent = <&gic>;
+				interrupts = <0 32 0>;
+			};
+		};
+
+		pinctrl_1: pinctrl@12290000 {
+			compatible = "samsung,exynos5260-pinctrl";
+			reg = <0x12290000 0x1000>;
+			interrupts = <0 157 0>;
+		};
+
+		pinctrl_2: pinctrl@128B0000 {
+			compatible = "samsung,exynos5260-pinctrl";
+			reg = <0x128B0000 0x1000>;
+			interrupts = <0 243 0>;
+		};
+
+		uart0: serial@12C00000 {
+			compatible = "samsung,exynos4210-uart";
+			reg = <0x12C00000 0x100>;
+			interrupts = <0 146 0>;
+			clocks = <&clock_peri PERI_CLK_UART0>, <&clock_peri PERI_SCLK_UART0>;
+			clock-names = "uart", "clk_uart_baud0";
+			status = "disabled";
+		};
+
+		uart1: serial@12C10000 {
+			compatible = "samsung,exynos4210-uart";
+			reg = <0x12C10000 0x100>;
+			interrupts = <0 147 0>;
+			clocks = <&clock_peri PERI_CLK_UART1>, <&clock_peri PERI_SCLK_UART1>;
+			clock-names = "uart", "clk_uart_baud0";
+			status = "disabled";
+		};
+
+		uart2: serial@12C20000 {
+			compatible = "samsung,exynos4210-uart";
+			reg = <0x12C20000 0x100>;
+			interrupts = <0 148 0>;
+			clocks = <&clock_peri PERI_CLK_UART2>, <&clock_peri PERI_SCLK_UART2>;
+			clock-names = "uart", "clk_uart_baud0";
+			status = "disabled";
+		};
+
+		uart3: serial@12860000 {
+			compatible = "samsung,exynos4210-uart";
+			reg = <0x12860000 0x100>;
+			interrupts = <0 145 0>;
+			clocks = <&clock_aud AUD_CLK_AUD_UART>, <&clock_aud AUD_SCLK_AUD_UART>;
+			clock-names = "uart", "clk_uart_baud0";
+			status = "disabled";
+		};
+
+		mmc_0: mmc@12140000 {
+			compatible = "samsung,exynos5250-dw-mshc";
+			reg = <0x12140000 0x2000>;
+			interrupts = <0 156 0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&clock_fsys FSYS_CLK_MMC0>, <&clock_top TOP_SCLK_MMC0>;
+			clock-names = "biu", "ciu";
+			fifo-depth = <64>;
+			status = "disabled";
+		};
+
+		mmc_1: mmc@12150000 {
+			compatible = "samsung,exynos5250-dw-mshc";
+			reg = <0x12150000 0x2000>;
+			interrupts = <0 158 0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&clock_fsys FSYS_CLK_MMC1>, <&clock_top TOP_SCLK_MMC1>;
+			clock-names = "biu", "ciu";
+			fifo-depth = <64>;
+			status = "disabled";
+		};
+
+		mmc_2: mmc@12160000 {
+			compatible = "samsung,exynos5250-dw-mshc";
+			reg = <0x12160000 0x2000>;
+			interrupts = <0 159 0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&clock_fsys FSYS_CLK_MMC2>, <&clock_top TOP_SCLK_MMC2>;
+			clock-names = "biu", "ciu";
+			fifo-depth = <64>;
+			status = "disabled";
+		};
+	};
+};
+
+#include "exynos5260-pinctrl.dtsi"
diff --git a/arch/arm/boot/dts/exynos5410-smdk5410.dts b/arch/arm/boot/dts/exynos5410-smdk5410.dts
new file mode 100644
index 0000000..7275bbd
--- /dev/null
+++ b/arch/arm/boot/dts/exynos5410-smdk5410.dts
@@ -0,0 +1,82 @@
+/*
+ * SAMSUNG SMDK5410 board device tree source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/dts-v1/;
+#include "exynos5410.dtsi"
+/ {
+	model = "Samsung SMDK5410 board based on EXYNOS5410";
+	compatible = "samsung,smdk5410", "samsung,exynos5410", "samsung,exynos5";
+
+	memory {
+		reg = <0x40000000 0x80000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttySAC2,115200";
+	};
+
+	fin_pll: xxti {
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		clock-output-names = "fin_pll";
+		#clock-cells = <0>;
+	};
+
+	firmware@02037000 {
+		compatible = "samsung,secure-firmware";
+		reg = <0x02037000 0x1000>;
+	};
+
+};
+
+&mmc_0 {
+	status = "okay";
+	num-slots = <1>;
+	supports-highspeed;
+	broken-cd;
+	card-detect-delay = <200>;
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-sdr-timing = <2 3>;
+	samsung,dw-mshc-ddr-timing = <1 2>;
+
+	slot@0 {
+		reg = <0>;
+		bus-width = <8>;
+	};
+};
+
+&mmc_2 {
+	status = "okay";
+	num-slots = <1>;
+	supports-highspeed;
+	card-detect-delay = <200>;
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-sdr-timing = <2 3>;
+	samsung,dw-mshc-ddr-timing = <1 2>;
+
+	slot@0 {
+		reg = <0>;
+		bus-width = <4>;
+		disable-wp;
+	};
+};
+
+&uart0 {
+		status = "okay";
+};
+
+&uart1 {
+		status = "okay";
+};
+
+&uart2 {
+		status = "okay";
+};
diff --git a/arch/arm/boot/dts/exynos5410.dtsi b/arch/arm/boot/dts/exynos5410.dtsi
new file mode 100644
index 0000000..3839c26
--- /dev/null
+++ b/arch/arm/boot/dts/exynos5410.dtsi
@@ -0,0 +1,206 @@
+/*
+ * SAMSUNG EXYNOS5410 SoC device tree source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * SAMSUNG EXYNOS5410 SoC device nodes are listed in this file.
+ * EXYNOS5410 based board files can include this file and provide
+ * values for board specfic bindings.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "skeleton.dtsi"
+#include <dt-bindings/clock/exynos5410.h>
+
+/ {
+	compatible = "samsung,exynos5410", "samsung,exynos5";
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CPU0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <0x0>;
+		};
+
+		CPU1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <0x1>;
+		};
+
+		CPU2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <0x2>;
+		};
+
+		CPU3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a15";
+			reg = <0x3>;
+		};
+	};
+
+	soc: soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		combiner: interrupt-controller@10440000 {
+			compatible = "samsung,exynos4210-combiner";
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			samsung,combiner-nr = <32>;
+			reg = <0x10440000 0x1000>;
+			interrupts =	<0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
+					<0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
+					<0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
+					<0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>,
+					<0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>,
+					<0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>,
+					<0 24 0>, <0 25 0>, <0 26 0>, <0 27 0>,
+					<0 28 0>, <0 29 0>, <0 30 0>, <0 31 0>;
+		};
+
+		gic: interrupt-controller@10481000 {
+			compatible = "arm,cortex-a15-gic", "arm,cortex-a9-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			reg =	<0x10481000 0x1000>,
+				<0x10482000 0x1000>,
+				<0x10484000 0x2000>,
+				<0x10486000 0x2000>;
+			interrupts = <1 9 0xf04>;
+		};
+
+		chipid@10000000 {
+			compatible = "samsung,exynos4210-chipid";
+			reg = <0x10000000 0x100>;
+		};
+
+		mct: mct@101C0000 {
+			compatible = "samsung,exynos4210-mct";
+			reg = <0x101C0000 0xB00>;
+			interrupt-parent = <&interrupt_map>;
+			interrupts = <0>, <1>, <2>, <3>,
+				<4>, <5>, <6>, <7>,
+				<8>, <9>, <10>, <11>;
+			clocks = <&fin_pll>, <&clock CLK_MCT>;
+			clock-names = "fin_pll", "mct";
+
+			interrupt_map: interrupt-map {
+				#interrupt-cells = <1>;
+				#address-cells = <0>;
+				#size-cells = <0>;
+				interrupt-map = <0 &combiner 23 3>,
+						<1 &combiner 23 4>,
+						<2 &combiner 25 2>,
+						<3 &combiner 25 3>,
+						<4 &gic 0 120 0>,
+						<5 &gic 0 121 0>,
+						<6 &gic 0 122 0>,
+						<7 &gic 0 123 0>,
+						<8 &gic 0 128 0>,
+						<9 &gic 0 129 0>,
+						<10 &gic 0 130 0>,
+						<11 &gic 0 131 0>;
+			};
+		};
+
+		sysram@02020000 {
+			compatible = "mmio-sram";
+			reg = <0x02020000 0x54000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x02020000 0x54000>;
+
+			smp-sysram@0 {
+				compatible = "samsung,exynos4210-sysram";
+				reg = <0x0 0x1000>;
+			};
+
+			smp-sysram@53000 {
+				compatible = "samsung,exynos4210-sysram-ns";
+				reg = <0x53000 0x1000>;
+			};
+		};
+
+		clock: clock-controller@10010000 {
+			compatible = "samsung,exynos5410-clock";
+			reg = <0x10010000 0x30000>;
+			#clock-cells = <1>;
+		};
+
+		mmc_0: mmc@12200000 {
+			compatible = "samsung,exynos5250-dw-mshc";
+			reg = <0x12200000 0x1000>;
+			interrupts = <0 75 0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&clock CLK_MMC0>, <&clock CLK_SCLK_MMC0>;
+			clock-names = "biu", "ciu";
+			fifo-depth = <0x80>;
+			status = "disabled";
+		};
+
+		mmc_1: mmc@12210000 {
+			compatible = "samsung,exynos5250-dw-mshc";
+			reg = <0x12210000 0x1000>;
+			interrupts = <0 76 0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&clock CLK_MMC1>, <&clock CLK_SCLK_MMC1>;
+			clock-names = "biu", "ciu";
+			fifo-depth = <0x80>;
+			status = "disabled";
+		};
+
+		mmc_2: mmc@12220000 {
+			compatible = "samsung,exynos5250-dw-mshc";
+			reg = <0x12220000 0x1000>;
+			interrupts = <0 77 0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&clock CLK_MMC2>, <&clock CLK_SCLK_MMC2>;
+			clock-names = "biu", "ciu";
+			fifo-depth = <0x80>;
+			status = "disabled";
+		};
+
+		uart0: serial@12C00000 {
+			compatible = "samsung,exynos4210-uart";
+			reg = <0x12C00000 0x100>;
+			interrupts = <0 51 0>;
+			clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>;
+			clock-names = "uart", "clk_uart_baud0";
+			status = "disabled";
+		};
+
+		uart1: serial@12C10000 {
+			compatible = "samsung,exynos4210-uart";
+			reg = <0x12C10000 0x100>;
+			interrupts = <0 52 0>;
+			clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>;
+			clock-names = "uart", "clk_uart_baud0";
+			status = "disabled";
+		};
+
+		uart2: serial@12C20000 {
+			compatible = "samsung,exynos4210-uart";
+			reg = <0x12C20000 0x100>;
+			interrupts = <0 53 0>;
+			clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
+			clock-names = "uart", "clk_uart_baud0";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/exynos5420-arndale-octa.dts b/arch/arm/boot/dts/exynos5420-arndale-octa.dts
index 6ee8149..434fd9d 100644
--- a/arch/arm/boot/dts/exynos5420-arndale-octa.dts
+++ b/arch/arm/boot/dts/exynos5420-arndale-octa.dts
@@ -26,6 +26,11 @@
 		bootargs = "console=ttySAC3,115200";
 	};
 
+	firmware@02073000 {
+		compatible = "samsung,secure-firmware";
+		reg = <0x02073000 0x1000>;
+	};
+
 	fixed-rate-clocks {
 		oscclk {
 			compatible = "samsung,exynos5420-oscclk";
diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts
index 29f64de9..1c5b8f9 100644
--- a/arch/arm/boot/dts/exynos5420-peach-pit.dts
+++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts
@@ -231,11 +231,11 @@
 	ddc = <&i2c_2>;
 };
 
-&usbdrd3_0 {
+&usbdrd_phy0 {
 	vbus-supply = <&usb300_vbus_reg>;
 };
 
-&usbdrd3_1 {
+&usbdrd_phy1 {
 	vbus-supply = <&usb301_vbus_reg>;
 };
 
diff --git a/arch/arm/boot/dts/exynos5440.dtsi b/arch/arm/boot/dts/exynos5440.dtsi
index 84f77c2..ae3a17c 100644
--- a/arch/arm/boot/dts/exynos5440.dtsi
+++ b/arch/arm/boot/dts/exynos5440.dtsi
@@ -176,7 +176,7 @@
 		clock-names = "i2c";
 	};
 
-	watchdog {
+	watchdog@110000 {
 		compatible = "samsung,s3c2410-wdt";
 		reg = <0x110000 0x1000>;
 		interrupts = <0 1 0>;
diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts
new file mode 100644
index 0000000..f3af207
--- /dev/null
+++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts
@@ -0,0 +1,253 @@
+/*
+ * Google Peach Pi Rev 10+ board device tree source
+ *
+ * Copyright (c) 2014 Google, Inc
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "exynos5800.dtsi"
+
+/ {
+	model = "Google Peach Pi Rev 10+";
+
+	compatible = "google,pi-rev16",
+		"google,pi-rev15", "google,pi-rev14",
+		"google,pi-rev13", "google,pi-rev12",
+		"google,pi-rev11", "google,pi-rev10",
+		"google,pi", "google,peach", "samsung,exynos5800",
+		"samsung,exynos5";
+
+	memory {
+		reg = <0x20000000 0x80000000>;
+	};
+
+	fixed-rate-clocks {
+		oscclk {
+			compatible = "samsung,exynos5420-oscclk";
+			clock-frequency = <24000000>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&power_key_irq>;
+
+		power {
+			label = "Power";
+			gpios = <&gpx1 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			gpio-key,wakeup;
+		};
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 1000000 0>;
+		brightness-levels = <0 100 500 1000 1500 2000 2500 2800>;
+		default-brightness-level = <7>;
+		pinctrl-0 = <&pwm0_out>;
+		pinctrl-names = "default";
+	};
+
+	usb300_vbus_reg: regulator-usb300 {
+		compatible = "regulator-fixed";
+		regulator-name = "P5.0V_USB3CON0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gph0 0 0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb300_vbus_en>;
+		enable-active-high;
+	};
+
+	usb301_vbus_reg: regulator-usb301 {
+		compatible = "regulator-fixed";
+		regulator-name = "P5.0V_USB3CON1";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gph0 1 0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb301_vbus_en>;
+		enable-active-high;
+	};
+};
+
+&pinctrl_0 {
+	tpm_irq: tpm-irq {
+		samsung,pins = "gpx1-0";
+		samsung,pin-function = <0>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	power_key_irq: power-key-irq {
+		samsung,pins = "gpx1-2";
+		samsung,pin-function = <0>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	dp_hpd_gpio: dp_hpd_gpio {
+		samsung,pins = "gpx2-6";
+		samsung,pin-function = <0>;
+		samsung,pin-pud = <3>;
+		samsung,pin-drv = <0>;
+	};
+
+	hdmi_hpd_irq: hdmi-hpd-irq {
+		samsung,pins = "gpx3-7";
+		samsung,pin-function = <0>;
+		samsung,pin-pud = <1>;
+		samsung,pin-drv = <0>;
+	};
+};
+
+&pinctrl_3 {
+	usb300_vbus_en: usb300-vbus-en {
+		samsung,pins = "gph0-0";
+		samsung,pin-function = <1>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	usb301_vbus_en: usb301-vbus-en {
+		samsung,pins = "gph0-1";
+		samsung,pin-function = <1>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+};
+
+&rtc {
+	status = "okay";
+};
+
+&uart_3 {
+	status = "okay";
+};
+
+&mmc_0 {
+	status = "okay";
+	num-slots = <1>;
+	broken-cd;
+	caps2-mmc-hs200-1_8v;
+	supports-highspeed;
+	non-removable;
+	card-detect-delay = <200>;
+	clock-frequency = <400000000>;
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-sdr-timing = <0 4>;
+	samsung,dw-mshc-ddr-timing = <0 2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>;
+
+	slot@0 {
+		reg = <0>;
+		bus-width = <8>;
+	};
+};
+
+&mmc_2 {
+	status = "okay";
+	num-slots = <1>;
+	supports-highspeed;
+	card-detect-delay = <200>;
+	clock-frequency = <400000000>;
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-sdr-timing = <2 3>;
+	samsung,dw-mshc-ddr-timing = <1 2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
+
+	slot@0 {
+		reg = <0>;
+		bus-width = <4>;
+	};
+};
+
+&dp {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&dp_hpd_gpio>;
+	samsung,color-space = <0>;
+	samsung,dynamic-range = <0>;
+	samsung,ycbcr-coeff = <0>;
+	samsung,color-depth = <1>;
+	samsung,link-rate = <0x0a>;
+	samsung,lane-count = <2>;
+	samsung,hpd-gpio = <&gpx2 6 0>;
+
+	display-timings {
+		native-mode = <&timing1>;
+
+		timing1: timing@1 {
+			clock-frequency = <150660000>;
+			hactive = <1920>;
+			vactive = <1080>;
+			hfront-porch = <60>;
+			hback-porch = <172>;
+			hsync-len = <80>;
+			vback-porch = <25>;
+			vfront-porch = <10>;
+			vsync-len = <10>;
+		};
+	};
+};
+
+&fimd {
+	status = "okay";
+	samsung,invert-vclk;
+};
+
+&hsi2c_9 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	tpm@20 {
+		compatible = "infineon,slb9645tt";
+		reg = <0x20>;
+		/* Unused irq; but still need to configure the pins */
+		pinctrl-names = "default";
+		pinctrl-0 = <&tpm_irq>;
+	};
+};
+
+&i2c_2 {
+	status = "okay";
+	samsung,i2c-sda-delay = <100>;
+	samsung,i2c-max-bus-freq = <66000>;
+	samsung,i2c-slave-addr = <0x50>;
+};
+
+&hdmi {
+	status = "okay";
+	hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdmi_hpd_irq>;
+	ddc = <&i2c_2>;
+};
+
+&usbdrd_phy0 {
+	vbus-supply = <&usb300_vbus_reg>;
+};
+
+&usbdrd_phy1 {
+	vbus-supply = <&usb301_vbus_reg>;
+};
+
+/*
+ * Use longest HW watchdog in SoC (32 seconds) since the hardware
+ * watchdog provides no debugging information (compared to soft/hard
+ * lockup detectors) and so should be last resort.
+ */
+&watchdog {
+	timeout-sec = <32>;
+};
diff --git a/arch/arm/boot/dts/exynos5800.dtsi b/arch/arm/boot/dts/exynos5800.dtsi
new file mode 100644
index 0000000..c0bb356
--- /dev/null
+++ b/arch/arm/boot/dts/exynos5800.dtsi
@@ -0,0 +1,28 @@
+/*
+ * SAMSUNG EXYNOS5800 SoC device tree source
+ *
+ * Copyright (c) 2014 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * SAMSUNG EXYNOS5800 SoC device nodes are listed in this file.
+ * EXYNOS5800 based board files can include this file and provide
+ * values for board specfic bindings.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "exynos5420.dtsi"
+
+/ {
+	compatible = "samsung,exynos5800", "samsung,exynos5";
+};
+
+&clock {
+	compatible = "samsung,exynos5800-clock";
+};
+
+&mfc {
+	compatible = "samsung,mfc-v8";
+};