[SCSI] pm8001: remove pm8001_slave_{alloc|configure}
libsas handles:
1/ limiting ata scanning to lun0
2/ changes to /sys/block/<sdX>/device/queue_depth for ata devices
libata handles turning off ncq globally via kernel command line
(libata.force=noncq) or sysfs (echo 1 >
/sys/block/<sdX>/device/queue_depth). A lldd specific compile option is
not necessary.
Cc: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
diff --git a/drivers/scsi/pm8001/pm8001_init.c b/drivers/scsi/pm8001/pm8001_init.c
index 172cefb..c21a216 100644
--- a/drivers/scsi/pm8001/pm8001_init.c
+++ b/drivers/scsi/pm8001/pm8001_init.c
@@ -61,7 +61,7 @@
.name = DRV_NAME,
.queuecommand = sas_queuecommand,
.target_alloc = sas_target_alloc,
- .slave_configure = pm8001_slave_configure,
+ .slave_configure = sas_slave_configure,
.slave_destroy = sas_slave_destroy,
.scan_finished = pm8001_scan_finished,
.scan_start = pm8001_scan_start,
@@ -76,7 +76,7 @@
.use_clustering = ENABLE_CLUSTERING,
.eh_device_reset_handler = sas_eh_device_reset_handler,
.eh_bus_reset_handler = sas_eh_bus_reset_handler,
- .slave_alloc = pm8001_slave_alloc,
+ .slave_alloc = sas_slave_alloc,
.target_destroy = sas_target_destroy,
.ioctl = sas_ioctl,
.shost_attrs = pm8001_host_attrs,
diff --git a/drivers/scsi/pm8001/pm8001_sas.c b/drivers/scsi/pm8001/pm8001_sas.c
index 7dbbf8b..9068f12 100644
--- a/drivers/scsi/pm8001/pm8001_sas.c
+++ b/drivers/scsi/pm8001/pm8001_sas.c
@@ -216,20 +216,6 @@
return rc;
}
-int pm8001_slave_alloc(struct scsi_device *scsi_dev)
-{
- struct domain_device *dev = sdev_to_domain_dev(scsi_dev);
- if (dev_is_sata(dev)) {
- /* We don't need to rescan targets
- * if REPORT_LUNS request is failed
- */
- if (scsi_dev->lun > 0)
- return -ENXIO;
- scsi_dev->tagged_supported = 1;
- }
- return sas_slave_alloc(scsi_dev);
-}
-
/**
* pm8001_scan_start - we should enable all HBA phys by sending the phy_start
* command to HBA.
@@ -314,22 +300,7 @@
{
return PM8001_CHIP_DISP->ssp_io_req(pm8001_ha, ccb);
}
-int pm8001_slave_configure(struct scsi_device *sdev)
-{
- struct domain_device *dev = sdev_to_domain_dev(sdev);
- int ret = sas_slave_configure(sdev);
- if (ret)
- return ret;
- if (dev_is_sata(dev)) {
- #ifdef PM8001_DISABLE_NCQ
- struct ata_port *ap = dev->sata_dev.ap;
- struct ata_device *adev = ap->link.device;
- adev->flags |= ATA_DFLAG_NCQ_OFF;
- scsi_adjust_queue_depth(sdev, MSG_SIMPLE_TAG, 1);
- #endif
- }
- return 0;
-}
+
/* Find the local port id that's attached to this device */
static int sas_find_local_port_id(struct domain_device *dev)
{
diff --git a/drivers/scsi/pm8001/pm8001_sas.h b/drivers/scsi/pm8001/pm8001_sas.h
index b97c8ab..93959fe 100644
--- a/drivers/scsi/pm8001/pm8001_sas.h
+++ b/drivers/scsi/pm8001/pm8001_sas.h
@@ -471,8 +471,6 @@
struct sas_task *task, struct pm8001_ccb_info *ccb, u32 ccb_idx);
int pm8001_phy_control(struct asd_sas_phy *sas_phy, enum phy_func func,
void *funcdata);
-int pm8001_slave_alloc(struct scsi_device *scsi_dev);
-int pm8001_slave_configure(struct scsi_device *sdev);
void pm8001_scan_start(struct Scsi_Host *shost);
int pm8001_scan_finished(struct Scsi_Host *shost, unsigned long time);
int pm8001_queue_command(struct sas_task *task, const int num,