Merge tag 'dt-part2-v2-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "part 2 of omap dts changes" from Tony Lindgren:
Changes to add dra7 PMU, display support for cm-t54, misc
changes needed for omap3 boards for device tree support.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'dt-part2-v2-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: DRA7: Add PMU nodes
ARM: dts: cm-t54: setup omap_dwc3
ARM: dts: cm-t54: add ADS7846 touchscreen support
ARM: dts: cm-t54: add Startek LCD support
ARM: dts: cm-t54: add HDMI/DVI display data
ARM: dts: cm-t54: fix mux mode comment style
ARM: dts: sbc-t54: fix mux mode comment style
ARM: dts: Enable PMIC idle configuration for LDP
ARM: dts: Add support for Ethernet on some N900 macro boards
ARM: dts: Do not set pulls for I2C lines
ARM: dts: omap: Remove WAKEUPENABLE mux options for UARTs
ARM: dts: omap3-overo: Fix UART wake-up events
diff --git a/arch/arm/boot/dts/dra72x.dtsi b/arch/arm/boot/dts/dra72x.dtsi
index f1ec22f..e5a3d23 100644
--- a/arch/arm/boot/dts/dra72x.dtsi
+++ b/arch/arm/boot/dts/dra72x.dtsi
@@ -22,4 +22,9 @@
reg = <0>;
};
};
+
+ pmu {
+ compatible = "arm,cortex-a15-pmu";
+ interrupts = <GIC_SPI DIRECT_IRQ(131) IRQ_TYPE_LEVEL_HIGH>;
+ };
};
diff --git a/arch/arm/boot/dts/dra74x.dtsi b/arch/arm/boot/dts/dra74x.dtsi
index a4e8bb9..3be544c 100644
--- a/arch/arm/boot/dts/dra74x.dtsi
+++ b/arch/arm/boot/dts/dra74x.dtsi
@@ -38,4 +38,10 @@
reg = <1>;
};
};
+
+ pmu {
+ compatible = "arm,cortex-a15-pmu";
+ interrupts = <GIC_SPI DIRECT_IRQ(131) IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI DIRECT_IRQ(132) IRQ_TYPE_LEVEL_HIGH>;
+ };
};
diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts
index 1becefc..06a8aec 100644
--- a/arch/arm/boot/dts/omap3-beagle-xm.dts
+++ b/arch/arm/boot/dts/omap3-beagle-xm.dts
@@ -174,8 +174,8 @@
uart3_pins: pinmux_uart3_pins {
pinctrl-single,pins = <
- 0x16e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
- 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */
+ 0x16e (PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
+ 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */
>;
};
diff --git a/arch/arm/boot/dts/omap3-ldp.dts b/arch/arm/boot/dts/omap3-ldp.dts
index af272c1..72dca0b 100644
--- a/arch/arm/boot/dts/omap3-ldp.dts
+++ b/arch/arm/boot/dts/omap3-ldp.dts
@@ -159,6 +159,11 @@
reg = <0x48>;
interrupts = <7>; /* SYS_NIRQ cascaded to intc */
interrupt-parent = <&intc>;
+
+ twl_power: power {
+ compatible = "ti,twl4030-power-idle";
+ ti,use_poweroff;
+ };
};
};
diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts
index 1fe45d1..19a5857 100644
--- a/arch/arm/boot/dts/omap3-n900.dts
+++ b/arch/arm/boot/dts/omap3-n900.dts
@@ -134,24 +134,32 @@
>;
};
+ ethernet_pins: pinmux_ethernet_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x20b4, PIN_INPUT_PULLDOWN | MUX_MODE4) /* gpmc_ncs3.gpio_54 */
+ OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE4) /* dss_data16.gpio_86 */
+ OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE4) /* uart3_rts_sd.gpio_164 */
+ >;
+ };
+
i2c1_pins: pinmux_i2c1_pins {
pinctrl-single,pins = <
- 0x18a (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */
- 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */
+ 0x18a (PIN_INPUT | MUX_MODE0) /* i2c1_scl */
+ 0x18c (PIN_INPUT | MUX_MODE0) /* i2c1_sda */
>;
};
i2c2_pins: pinmux_i2c2_pins {
pinctrl-single,pins = <
- 0x18e (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_scl */
- 0x190 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_sda */
+ 0x18e (PIN_INPUT | MUX_MODE0) /* i2c2_scl */
+ 0x190 (PIN_INPUT | MUX_MODE0) /* i2c2_sda */
>;
};
i2c3_pins: pinmux_i2c3_pins {
pinctrl-single,pins = <
- 0x192 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */
- 0x194 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */
+ 0x192 (PIN_INPUT | MUX_MODE0) /* i2c3_scl */
+ 0x194 (PIN_INPUT | MUX_MODE0) /* i2c3_sda */
>;
};
@@ -578,6 +586,8 @@
&gpmc {
ranges = <0 0 0x04000000 0x10000000>; /* 256MB */
+ ranges = <0 0 0x01000000 0x01000000>, /* 16 MB for OneNAND */
+ <1 0 0x02000000 0x01000000>; /* 16 MB for smc91c96 */
/* gpio-irq for dma: 65 */
@@ -646,6 +656,38 @@
reg = <0x004c0000 0x0fb40000>;
};
};
+
+ ethernet@gpmc {
+ compatible = "smsc,lan91c94";
+ interrupt-parent = <&gpio2>;
+ interrupts = <22 IRQ_TYPE_LEVEL_HIGH>; /* gpio54 */
+ reg = <1 0x300 0xf>; /* 16 byte IO range at offset 0x300 */
+ bank-width = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <ðernet_pins>;
+ gpmc,device-width = <2>;
+ gpmc,sync-clk-ps = <0>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <48>;
+ gpmc,cs-wr-off-ns = <24>;
+ gpmc,adv-on-ns = <0>;
+ gpmc,adv-rd-off-ns = <0>;
+ gpmc,adv-wr-off-ns = <0>;
+ gpmc,we-on-ns = <12>;
+ gpmc,we-off-ns = <18>;
+ gpmc,oe-on-ns = <12>;
+ gpmc,oe-off-ns = <48>;
+ gpmc,page-burst-access-ns = <0>;
+ gpmc,access-ns = <42>;
+ gpmc,rd-cycle-ns = <180>;
+ gpmc,wr-cycle-ns = <180>;
+ gpmc,bus-turnaround-ns = <0>;
+ gpmc,cycle2cycle-delay-ns = <0>;
+ gpmc,wait-monitoring-ns = <0>;
+ gpmc,clk-activation-ns = <0>;
+ gpmc,wr-access-ns = <0>;
+ gpmc,wr-data-mux-bus-ns = <12>;
+ };
};
&mcspi1 {
diff --git a/arch/arm/boot/dts/omap3-overo-common-peripherals.dtsi b/arch/arm/boot/dts/omap3-overo-common-peripherals.dtsi
index 5831bcc..520453d 100644
--- a/arch/arm/boot/dts/omap3-overo-common-peripherals.dtsi
+++ b/arch/arm/boot/dts/omap3-overo-common-peripherals.dtsi
@@ -36,8 +36,8 @@
uart3_pins: pinmux_uart3_pins {
pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
- OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
+ OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
+ OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
>;
};
};
@@ -88,6 +88,7 @@
};
&uart3 {
+ interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>;
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins>;
};
diff --git a/arch/arm/boot/dts/omap5-cm-t54.dts b/arch/arm/boot/dts/omap5-cm-t54.dts
index b8698ca..880333a 100644
--- a/arch/arm/boot/dts/omap5-cm-t54.dts
+++ b/arch/arm/boot/dts/omap5-cm-t54.dts
@@ -16,6 +16,12 @@
reg = <0x80000000 0x7F000000>; /* 2048 MB */
};
+ aliases {
+ display0 = &hdmi0;
+ display1 = &dvi0;
+ display2 = &lcd0;
+ };
+
vmmcsd_fixed: fixed-regulator-mmcsd {
compatible = "regulator-fixed";
regulator-name = "vmmcsd_fixed";
@@ -45,6 +51,13 @@
enable-active-high;
};
+ ads7846reg: ads7846-reg {
+ compatible = "regulator-fixed";
+ regulator-name = "ads7846-reg";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
/* HS USB Host PHY on PORT 2 */
hsusb2_phy: hsusb2_phy {
compatible = "usb-nop-xceiv";
@@ -66,6 +79,105 @@
default-state = "off";
};
};
+
+ lcd0: display {
+ compatible = "startek,startek-kd050c", "panel-dpi";
+ label = "lcd";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_pins>;
+
+ enable-gpios = <&gpio8 3 GPIO_ACTIVE_HIGH>;
+
+ panel-timing {
+ clock-frequency = <33000000>;
+ hactive = <800>;
+ vactive = <480>;
+ hfront-porch = <40>;
+ hback-porch = <40>;
+ hsync-len = <43>;
+ vback-porch = <29>;
+ vfront-porch = <13>;
+ vsync-len = <3>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+
+ port {
+ lcd_in: endpoint {
+ remote-endpoint = <&dpi_lcd_out>;
+ };
+ };
+ };
+
+ hdmi0: connector@0 {
+ compatible = "hdmi-connector";
+ label = "hdmi";
+
+ type = "a";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdmi_conn_pins>;
+
+ hpd-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>; /* GPIO 193, HPD */
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&hdmi_out>;
+ };
+ };
+ };
+
+ tfp410: encoder@0 {
+ compatible = "ti,tfp410";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tfp410_in: endpoint@0 {
+ remote-endpoint = <&dpi_dvi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tfp410_out: endpoint@0 {
+ remote-endpoint = <&dvi_connector_in>;
+ };
+ };
+ };
+ };
+
+ dvi0: connector@1 {
+ compatible = "dvi-connector";
+ label = "dvi";
+
+ digital;
+
+ ddc-i2c-bus = <&i2c2>;
+
+ port {
+ dvi_connector_in: endpoint {
+ remote-endpoint = <&tfp410_out>;
+ };
+ };
+ };
+};
+
+&omap5_pmx_wkup {
+
+ ads7846_pins: pinmux_ads7846_pins {
+ pinctrl-single,pins = <
+ 0x02 (PIN_INPUT_PULLDOWN | MUX_MODE6) /* llib_wakereqin.gpio1_wk15 */
+ >;
+ };
};
&omap5_pmx_core {
@@ -88,6 +200,13 @@
>;
};
+ i2c2_pins: pinmux_i2c2_pins {
+ pinctrl-single,pins = <
+ OMAP5_IOPAD(0x01b8, PIN_INPUT | MUX_MODE0) /* i2c2_scl */
+ OMAP5_IOPAD(0x01ba, PIN_INPUT | MUX_MODE0) /* i2c2_sda */
+ >;
+ };
+
mmc1_pins: pinmux_mmc1_pins {
pinctrl-single,pins = <
OMAP5_IOPAD(0x01e2, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_clk */
@@ -127,8 +246,8 @@
wlan_gpios_pins: pinmux_wlan_gpios_pins {
pinctrl-single,pins = <
- OMAP5_IOPAD(0x019c, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* gpio4_109 */
- OMAP5_IOPAD(0x019e, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* gpio4_110 */
+ OMAP5_IOPAD(0x019c, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* abemcpdm_ul_data.gpio4_109 */
+ OMAP5_IOPAD(0x019e, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* abemcpdm_dl_data.gpio4_110 */
>;
};
@@ -144,6 +263,104 @@
OMAP5_IOPAD(0x00b6, PIN_OUTPUT | MUX_MODE6) /* hsi2_acdata.gpio3_83 */
>;
};
+
+ dss_hdmi_pins: pinmux_dss_hdmi_pins {
+ pinctrl-single,pins = <
+ OMAP5_IOPAD(0x013c, PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec */
+ OMAP5_IOPAD(0x0140, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl */
+ OMAP5_IOPAD(0x0142, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda */
+ >;
+ };
+
+ lcd_pins: pinmux_lcd_pins {
+ pinctrl-single,pins = <
+ OMAP5_IOPAD(0x0172, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* timer11_pwm_evt.gpio8_227 */
+ >;
+ };
+
+ hdmi_conn_pins: pinmux_hdmi_conn_pins {
+ pinctrl-single,pins = <
+ OMAP5_IOPAD(0x013e, PIN_INPUT | MUX_MODE6) /* hdmi_hpd.gpio7_193 */
+ >;
+ };
+
+ dss_dpi_pins: pinmux_dss_dpi_pins {
+ pinctrl-single,pins = <
+ OMAP5_IOPAD(0x0104, PIN_OUTPUT | MUX_MODE3) /* rfbi_data15.dispc_data15 */
+ OMAP5_IOPAD(0x0106, PIN_OUTPUT | MUX_MODE3) /* rfbi_data14.dispc_data14 */
+ OMAP5_IOPAD(0x0108, PIN_OUTPUT | MUX_MODE3) /* rfbi_data13.dispc_data13 */
+ OMAP5_IOPAD(0x010a, PIN_OUTPUT | MUX_MODE3) /* rfbi_data12.dispc_data12 */
+ OMAP5_IOPAD(0x010c, PIN_OUTPUT | MUX_MODE3) /* rfbi_data11.dispc_data11 */
+ OMAP5_IOPAD(0x010e, PIN_OUTPUT | MUX_MODE3) /* rfbi_data10.dispc_data10 */
+ OMAP5_IOPAD(0x0110, PIN_OUTPUT | MUX_MODE3) /* rfbi_data9.dispc_data9 */
+ OMAP5_IOPAD(0x0112, PIN_OUTPUT | MUX_MODE3) /* rfbi_data8.dispc_data8 */
+ OMAP5_IOPAD(0x0114, PIN_OUTPUT | MUX_MODE3) /* rfbi_data7.dispc_data7 */
+ OMAP5_IOPAD(0x0116, PIN_OUTPUT | MUX_MODE3) /* rfbi_data6.dispc_data6 */
+ OMAP5_IOPAD(0x0118, PIN_OUTPUT | MUX_MODE3) /* rfbi_data5.dispc_data5 */
+ OMAP5_IOPAD(0x011a, PIN_OUTPUT | MUX_MODE3) /* rfbi_data4.dispc_data4 */
+ OMAP5_IOPAD(0x011c, PIN_OUTPUT | MUX_MODE3) /* rfbi_data3.dispc_data3 */
+ OMAP5_IOPAD(0x011e, PIN_OUTPUT | MUX_MODE3) /* rfbi_data2.dispc_data2 */
+ OMAP5_IOPAD(0x0120, PIN_OUTPUT | MUX_MODE3) /* rfbi_data1.dispc_data1 */
+ OMAP5_IOPAD(0x0122, PIN_OUTPUT | MUX_MODE3) /* rfbi_data0.dispc_data0 */
+ OMAP5_IOPAD(0x0124, PIN_OUTPUT | MUX_MODE3) /* rfbi_we.dispc_vsync */
+ OMAP5_IOPAD(0x0126, PIN_OUTPUT | MUX_MODE3) /* rfbi_cs0.dispc_hsync */
+ OMAP5_IOPAD(0x0128, PIN_OUTPUT | MUX_MODE3) /* rfbi_a0.dispc_de */
+ OMAP5_IOPAD(0x012a, PIN_OUTPUT | MUX_MODE3) /* rfbi_re.dispc_pclk */
+ OMAP5_IOPAD(0x012c, PIN_OUTPUT | MUX_MODE3) /* rfbi_hsync0.dispc_data17 */
+ OMAP5_IOPAD(0x012e, PIN_OUTPUT | MUX_MODE3) /* rfbi_te_vsync0.dispc_data16 */
+ OMAP5_IOPAD(0x0130, PIN_OUTPUT | MUX_MODE3) /* gpio6_182.dispc_data18 */
+ OMAP5_IOPAD(0x0132, PIN_OUTPUT | MUX_MODE3) /* gpio6_183.dispc_data19 */
+ OMAP5_IOPAD(0x0134, PIN_OUTPUT | MUX_MODE3) /* gpio6_184.dispc_data20 */
+ OMAP5_IOPAD(0x0136, PIN_OUTPUT | MUX_MODE3) /* gpio6_185.dispc_data21 */
+ OMAP5_IOPAD(0x0138, PIN_OUTPUT | MUX_MODE3) /* gpio6_186.dispc_data22 */
+ OMAP5_IOPAD(0x013a, PIN_OUTPUT | MUX_MODE3) /* gpio6_187.dispc_data23 */
+ >;
+ };
+
+ mcspi2_pins: pinmux_mcspi1_pins {
+ pinctrl-single,pins = <
+ OMAP5_IOPAD(0x00fc, PIN_INPUT | MUX_MODE0) /* mcspi2_clk */
+ OMAP5_IOPAD(0x00fe, PIN_INPUT | MUX_MODE0) /* mcspi2_simo */
+ OMAP5_IOPAD(0x0100, PIN_INPUT | MUX_MODE0) /* mcspi2_somi */
+ OMAP5_IOPAD(0x0102, PIN_INPUT | MUX_MODE0) /* mcspi2_cs0 */
+ >;
+ };
+};
+
+&mcspi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcspi2_pins>;
+
+ /* touch controller */
+ ads7846@0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ads7846_pins>;
+
+ compatible = "ti,ads7846";
+ vcc-supply = <&ads7846reg>;
+
+ reg = <0>; /* CS0 */
+ spi-max-frequency = <1500000>;
+
+ interrupt-parent = <&gpio1>;
+ interrupts = <15 0>; /* gpio1_wk15 */
+ pendown-gpio = <&gpio1 15 0>;
+
+
+ ti,x-min = /bits/ 16 <0x0>;
+ ti,x-max = /bits/ 16 <0x0fff>;
+ ti,y-min = /bits/ 16 <0x0>;
+ ti,y-max = /bits/ 16 <0x0fff>;
+
+ ti,x-plate-ohms = /bits/ 16 <180>;
+ ti,pressure-max = /bits/ 16 <255>;
+
+ ti,debounce-max = /bits/ 16 <30>;
+ ti,debounce-tol = /bits/ 16 <10>;
+ ti,debounce-rep = /bits/ 16 <1>;
+
+ linux,wakeup;
+ };
};
&mmc1 {
@@ -399,6 +616,13 @@
};
};
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+
+ clock-frequency = <100000>;
+};
+
&usbhshost {
port2-mode = "ehci-hsic";
port3-mode = "ehci-hsic";
@@ -408,6 +632,50 @@
phys = <0 &hsusb2_phy &hsusb3_phy>;
};
+&usb3 {
+ extcon = <&extcon_usb3>;
+ vbus-supply = <&smps10_out1_reg>;
+};
+
&cpu0 {
cpu0-supply = <&smps123_reg>;
};
+
+&dss {
+ status = "ok";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dss_dpi_pins>;
+
+ port {
+ dpi_dvi_out: endpoint@0 {
+ remote-endpoint = <&tfp410_in>;
+ data-lines = <24>;
+ };
+
+ dpi_lcd_out: endpoint@1 {
+ remote-endpoint = <&lcd_in>;
+ data-lines = <24>;
+ };
+ };
+};
+
+&dsi2 {
+ status = "ok";
+ vdd-supply = <&ldo4_reg>;
+};
+
+&hdmi {
+ status = "ok";
+ vdda-supply = <&ldo4_reg>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dss_hdmi_pins>;
+
+ port {
+ hdmi_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ lanes = <1 0 3 2 5 4 7 6>;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/omap5-sbc-t54.dts b/arch/arm/boot/dts/omap5-sbc-t54.dts
index 8e89793..337bbbc 100644
--- a/arch/arm/boot/dts/omap5-sbc-t54.dts
+++ b/arch/arm/boot/dts/omap5-sbc-t54.dts
@@ -19,8 +19,8 @@
mmc1_aux_pins: pinmux_mmc1_aux_pins {
pinctrl-single,pins = <
- OMAP5_IOPAD(0x0174, PIN_INPUT_PULLUP | MUX_MODE6) /* gpio8_228 */
- OMAP5_IOPAD(0x0176, PIN_INPUT_PULLUP | MUX_MODE6) /* gpio8_229 */
+ OMAP5_IOPAD(0x0174, PIN_INPUT_PULLUP | MUX_MODE6) /* timer5_pwm_evt.gpio8_228 */
+ OMAP5_IOPAD(0x0176, PIN_INPUT_PULLUP | MUX_MODE6) /* timer6_pwm_evt.gpio8_229 */
>;
};
};
diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c
index b9d091b..61e8394 100644
--- a/arch/arm/mach-omap2/pdata-quirks.c
+++ b/arch/arm/mach-omap2/pdata-quirks.c
@@ -252,6 +252,9 @@
platform_device_register(&omap3_rom_rng_device);
}
+
+ /* Only on some development boards */
+ gpio_request_one(164, GPIOF_OUT_INIT_LOW, "smc91x reset");
}
static void __init omap3_tao3530_legacy_init(void)