ARM: ux500: get rid of <mach/[hardware|db8500-regs].h>
This removes <mach/hardware.h> and <mach/db8500-regs.h>
from the Ux500, merging them into the local include
"db8500-regs.h" in mach-ux500. There is some impact
outside the ux500 machine, but most of it is dealt with
in earlier patches.
Contains portions of a clean-up patch from Arnd Bergmann.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
diff --git a/arch/arm/mach-ux500/db8500-regs.h b/arch/arm/mach-ux500/db8500-regs.h
new file mode 100644
index 0000000..b2d7a0b
--- /dev/null
+++ b/arch/arm/mach-ux500/db8500-regs.h
@@ -0,0 +1,201 @@
+/*
+ * Copyright (C) ST-Ericsson SA 2010
+ *
+ * License terms: GNU General Public License (GPL) version 2
+ */
+
+#ifndef __MACH_DB8500_REGS_H
+#define __MACH_DB8500_REGS_H
+
+/* Base address and bank offsets for ESRAM */
+#define U8500_ESRAM_BASE 0x40000000
+#define U8500_ESRAM_BANK_SIZE 0x00020000
+#define U8500_ESRAM_BANK0 U8500_ESRAM_BASE
+#define U8500_ESRAM_BANK1 (U8500_ESRAM_BASE + U8500_ESRAM_BANK_SIZE)
+#define U8500_ESRAM_BANK2 (U8500_ESRAM_BANK1 + U8500_ESRAM_BANK_SIZE)
+#define U8500_ESRAM_BANK3 (U8500_ESRAM_BANK2 + U8500_ESRAM_BANK_SIZE)
+#define U8500_ESRAM_BANK4 (U8500_ESRAM_BANK3 + U8500_ESRAM_BANK_SIZE)
+/*
+ * on V1 DMA uses 4KB for logical parameters position is right after the 64KB
+ * reserved for security
+ */
+#define U8500_ESRAM_DMA_LCPA_OFFSET 0x10000
+
+#define U8500_DMA_LCPA_BASE (U8500_ESRAM_BANK0 + U8500_ESRAM_DMA_LCPA_OFFSET)
+
+/* This address fulfills the 256k alignment requirement of the lcla base */
+#define U8500_DMA_LCLA_BASE U8500_ESRAM_BANK4
+
+#define U8500_PER3_BASE 0x80000000
+#define U8500_STM_BASE 0x80100000
+#define U8500_STM_REG_BASE (U8500_STM_BASE + 0xF000)
+#define U8500_PER2_BASE 0x80110000
+#define U8500_PER1_BASE 0x80120000
+#define U8500_B2R2_BASE 0x80130000
+#define U8500_HSEM_BASE 0x80140000
+#define U8500_PER4_BASE 0x80150000
+#define U8500_TPIU_BASE 0x80190000
+#define U8500_ICN_BASE 0x81000000
+
+#define U8500_BOOT_ROM_BASE 0x90000000
+/* ASIC ID is at 0xbf4 offset within this region */
+#define U8500_ASIC_ID_BASE 0x9001D000
+
+#define U9540_BOOT_ROM_BASE 0xFFFE0000
+/* ASIC ID is at 0xbf4 offset within this region */
+#define U9540_ASIC_ID_BASE 0xFFFFD000
+
+#define U8500_PER6_BASE 0xa03c0000
+#define U8500_PER7_BASE 0xa03d0000
+#define U8500_PER5_BASE 0xa03e0000
+
+#define U8500_SVA_BASE 0xa0100000
+#define U8500_SIA_BASE 0xa0200000
+
+#define U8500_SGA_BASE 0xa0300000
+#define U8500_MCDE_BASE 0xa0350000
+#define U8500_DMA_BASE 0x801C0000 /* v1 */
+
+#define U8500_SBAG_BASE 0xa0390000
+
+#define U8500_SCU_BASE 0xa0410000
+#define U8500_GIC_CPU_BASE 0xa0410100
+#define U8500_TWD_BASE 0xa0410600
+#define U8500_GIC_DIST_BASE 0xa0411000
+#define U8500_L2CC_BASE 0xa0412000
+
+#define U8500_MODEM_I2C 0xb7e02000
+
+#define U8500_GPIO0_BASE (U8500_PER1_BASE + 0xE000)
+#define U8500_GPIO1_BASE (U8500_PER3_BASE + 0xE000)
+#define U8500_GPIO2_BASE (U8500_PER2_BASE + 0xE000)
+#define U8500_GPIO3_BASE (U8500_PER5_BASE + 0x1E000)
+
+#define U8500_UART0_BASE (U8500_PER1_BASE + 0x0000)
+#define U8500_UART1_BASE (U8500_PER1_BASE + 0x1000)
+
+/* per6 base addresses */
+#define U8500_RNG_BASE (U8500_PER6_BASE + 0x0000)
+#define U8500_HASH0_BASE (U8500_PER6_BASE + 0x1000)
+#define U8500_HASH1_BASE (U8500_PER6_BASE + 0x2000)
+#define U8500_PKA_BASE (U8500_PER6_BASE + 0x4000)
+#define U8500_PKAM_BASE (U8500_PER6_BASE + 0x5100)
+#define U8500_MTU0_BASE (U8500_PER6_BASE + 0x6000) /* v1 */
+#define U8500_MTU1_BASE (U8500_PER6_BASE + 0x7000) /* v1 */
+#define U8500_CR_BASE (U8500_PER6_BASE + 0x8000) /* v1 */
+#define U8500_CRYP0_BASE (U8500_PER6_BASE + 0xa000)
+#define U8500_CRYP1_BASE (U8500_PER6_BASE + 0xb000)
+#define U8500_CLKRST6_BASE (U8500_PER6_BASE + 0xf000)
+
+/* per5 base addresses */
+#define U8500_USBOTG_BASE (U8500_PER5_BASE + 0x00000)
+#define U8500_CLKRST5_BASE (U8500_PER5_BASE + 0x1f000)
+
+/* per4 base addresses */
+#define U8500_BACKUPRAM0_BASE (U8500_PER4_BASE + 0x00000)
+#define U8500_BACKUPRAM1_BASE (U8500_PER4_BASE + 0x01000)
+#define U8500_RTT0_BASE (U8500_PER4_BASE + 0x02000)
+#define U8500_RTT1_BASE (U8500_PER4_BASE + 0x03000)
+#define U8500_RTC_BASE (U8500_PER4_BASE + 0x04000)
+#define U8500_SCR_BASE (U8500_PER4_BASE + 0x05000)
+#define U8500_DMC_BASE (U8500_PER4_BASE + 0x06000)
+#define U8500_PRCMU_BASE (U8500_PER4_BASE + 0x07000)
+#define U9540_DMC1_BASE (U8500_PER4_BASE + 0x0A000)
+#define U8500_PRCMU_TCDM_BASE (U8500_PER4_BASE + 0x68000)
+#define U9540_PRCMU_TCDM_BASE (U8500_PER4_BASE + 0x6A000)
+#define U8500_PRCMU_TCPM_BASE (U8500_PER4_BASE + 0x60000)
+#define U8500_PRCMU_TIMER_3_BASE (U8500_PER4_BASE + 0x07338)
+#define U8500_PRCMU_TIMER_4_BASE (U8500_PER4_BASE + 0x07450)
+
+/* per3 base addresses */
+#define U8500_FSMC_BASE (U8500_PER3_BASE + 0x0000)
+#define U8500_SSP0_BASE (U8500_PER3_BASE + 0x2000)
+#define U8500_SSP1_BASE (U8500_PER3_BASE + 0x3000)
+#define U8500_I2C0_BASE (U8500_PER3_BASE + 0x4000)
+#define U8500_SDI2_BASE (U8500_PER3_BASE + 0x5000)
+#define U8500_SKE_BASE (U8500_PER3_BASE + 0x6000)
+#define U8500_UART2_BASE (U8500_PER3_BASE + 0x7000)
+#define U8500_SDI5_BASE (U8500_PER3_BASE + 0x8000)
+#define U8500_CLKRST3_BASE (U8500_PER3_BASE + 0xf000)
+
+/* per2 base addresses */
+#define U8500_I2C3_BASE (U8500_PER2_BASE + 0x0000)
+#define U8500_SPI2_BASE (U8500_PER2_BASE + 0x1000)
+#define U8500_SPI1_BASE (U8500_PER2_BASE + 0x2000)
+#define U8500_PWL_BASE (U8500_PER2_BASE + 0x3000)
+#define U8500_SDI4_BASE (U8500_PER2_BASE + 0x4000)
+#define U8500_MSP2_BASE (U8500_PER2_BASE + 0x7000)
+#define U8500_SDI1_BASE (U8500_PER2_BASE + 0x8000)
+#define U8500_SDI3_BASE (U8500_PER2_BASE + 0x9000)
+#define U8500_SPI0_BASE (U8500_PER2_BASE + 0xa000)
+#define U8500_HSIR_BASE (U8500_PER2_BASE + 0xb000)
+#define U8500_HSIT_BASE (U8500_PER2_BASE + 0xc000)
+#define U8500_CLKRST2_BASE (U8500_PER2_BASE + 0xf000)
+
+/* per1 base addresses */
+#define U8500_I2C1_BASE (U8500_PER1_BASE + 0x2000)
+#define U8500_MSP0_BASE (U8500_PER1_BASE + 0x3000)
+#define U8500_MSP1_BASE (U8500_PER1_BASE + 0x4000)
+#define U8500_MSP3_BASE (U8500_PER1_BASE + 0x5000)
+#define U8500_SDI0_BASE (U8500_PER1_BASE + 0x6000)
+#define U8500_I2C2_BASE (U8500_PER1_BASE + 0x8000)
+#define U8500_SPI3_BASE (U8500_PER1_BASE + 0x9000)
+#define U8500_I2C4_BASE (U8500_PER1_BASE + 0xa000)
+#define U8500_SLIM0_BASE (U8500_PER1_BASE + 0xb000)
+#define U8500_CLKRST1_BASE (U8500_PER1_BASE + 0xf000)
+
+#define U8500_SHRM_GOP_INTERRUPT_BASE 0xB7C00040
+
+#define U8500_GPIOBANK0_BASE U8500_GPIO0_BASE
+#define U8500_GPIOBANK1_BASE (U8500_GPIO0_BASE + 0x80)
+#define U8500_GPIOBANK2_BASE U8500_GPIO1_BASE
+#define U8500_GPIOBANK3_BASE (U8500_GPIO1_BASE + 0x80)
+#define U8500_GPIOBANK4_BASE (U8500_GPIO1_BASE + 0x100)
+#define U8500_GPIOBANK5_BASE (U8500_GPIO1_BASE + 0x180)
+#define U8500_GPIOBANK6_BASE U8500_GPIO2_BASE
+#define U8500_GPIOBANK7_BASE (U8500_GPIO2_BASE + 0x80)
+#define U8500_GPIOBANK8_BASE U8500_GPIO3_BASE
+
+#define U8500_MCDE_SIZE 0x1000
+#define U8500_DSI_LINK_SIZE 0x1000
+#define U8500_DSI_LINK1_BASE (U8500_MCDE_BASE + U8500_MCDE_SIZE)
+#define U8500_DSI_LINK2_BASE (U8500_DSI_LINK1_BASE + U8500_DSI_LINK_SIZE)
+#define U8500_DSI_LINK3_BASE (U8500_DSI_LINK2_BASE + U8500_DSI_LINK_SIZE)
+#define U8500_DSI_LINK_COUNT 0x3
+
+/* Modem and APE physical addresses */
+#define U8500_MODEM_BASE 0xe000000
+#define U8500_APE_BASE 0x6000000
+
+/* SoC identification number information */
+#define U8500_BB_UID_BASE (U8500_BACKUPRAM1_BASE + 0xFC0)
+
+/* Offsets to specific addresses in some IP blocks for DMA */
+#define MSP_TX_RX_REG_OFFSET 0
+#define CRYP1_RX_REG_OFFSET 0x10
+#define CRYP1_TX_REG_OFFSET 0x8
+#define HASH1_TX_REG_OFFSET 0x4
+
+/*
+ * Macros to get at IO space when running virtually
+ * We dont map all the peripherals, let ioremap do
+ * this for us. We map only very basic peripherals here.
+ */
+#define U8500_IO_VIRTUAL 0xf0000000
+#define U8500_IO_PHYSICAL 0xa0000000
+/* This is where we map in the ROM to check ASIC IDs */
+#define UX500_VIRT_ROM 0xf0000000
+
+/* This macro is used in assembly, so no cast */
+#define IO_ADDRESS(x) \
+ (((x) & 0x0fffffff) + (((x) >> 4) & 0x0f000000) + U8500_IO_VIRTUAL)
+
+/* typesafe io address */
+#define __io_address(n) IOMEM(IO_ADDRESS(n))
+
+/* Used by some plat-nomadik code */
+#define io_p2v(n) __io_address(n)
+
+#define ARRAY_AND_SIZE(x) (x), ARRAY_SIZE(x)
+
+#endif