mac68k: start CUDA early
The valkyriefb driver needs the CUDA to work in order to set the video
mode at boot. So initialise the device earlier, and bring the m68k code
closer to the powermac code.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
diff --git a/drivers/macintosh/via-cuda.c b/drivers/macintosh/via-cuda.c
index 62dd1fd..971bc95 100644
--- a/drivers/macintosh/via-cuda.c
+++ b/drivers/macintosh/via-cuda.c
@@ -89,7 +89,6 @@
#ifdef CONFIG_ADB
static int cuda_probe(void);
-static int cuda_init(void);
static int cuda_send_request(struct adb_request *req, int sync);
static int cuda_adb_autopoll(int devs);
static int cuda_reset_adb_bus(void);
@@ -107,17 +106,42 @@
#ifdef CONFIG_ADB
struct adb_driver via_cuda_driver = {
- "CUDA",
- cuda_probe,
- cuda_init,
- cuda_send_request,
- cuda_adb_autopoll,
- cuda_poll,
- cuda_reset_adb_bus
+ .name = "CUDA",
+ .probe = cuda_probe,
+ .send_request = cuda_send_request,
+ .autopoll = cuda_adb_autopoll,
+ .poll = cuda_poll,
+ .reset_bus = cuda_reset_adb_bus,
};
#endif /* CONFIG_ADB */
-#ifdef CONFIG_PPC
+#ifdef CONFIG_MAC
+int __init find_via_cuda(void)
+{
+ struct adb_request req;
+ int err;
+
+ if (macintosh_config->adb_type != MAC_ADB_CUDA)
+ return 0;
+
+ via = via1;
+ cuda_state = idle;
+
+ err = cuda_init_via();
+ if (err) {
+ printk(KERN_ERR "cuda_init_via() failed\n");
+ via = NULL;
+ return 0;
+ }
+
+ /* enable autopoll */
+ cuda_request(&req, NULL, 3, CUDA_PACKET, CUDA_AUTOPOLL, 1);
+ while (!req.complete)
+ cuda_poll();
+
+ return 1;
+}
+#else
int __init find_via_cuda(void)
{
struct adb_request req;
@@ -175,7 +199,7 @@
vias = NULL;
return 0;
}
-#endif /* CONFIG_PPC */
+#endif /* !defined CONFIG_MAC */
static int __init via_cuda_start(void)
{
@@ -184,14 +208,14 @@
#ifdef CONFIG_MAC
cuda_irq = IRQ_MAC_ADB;
-#else /* CONFIG_MAC */
+#else
cuda_irq = irq_of_parse_and_map(vias, 0);
if (cuda_irq == NO_IRQ) {
printk(KERN_ERR "via-cuda: can't map interrupts for %s\n",
vias->full_name);
return -ENODEV;
}
-#endif /* CONFIG_MAC */
+#endif
if (request_irq(cuda_irq, cuda_interrupt, 0, "ADB", cuda_interrupt)) {
printk(KERN_ERR "via-cuda: can't request irq %d\n", cuda_irq);
@@ -216,28 +240,10 @@
#else
if (macintosh_config->adb_type != MAC_ADB_CUDA)
return -ENODEV;
- via = via1;
#endif
- return 0;
-}
-
-static int __init
-cuda_init(void)
-{
-#ifdef CONFIG_PPC
if (via == NULL)
return -ENODEV;
return 0;
-#else
- int err = cuda_init_via();
- if (err) {
- printk(KERN_ERR "cuda_init_via() failed\n");
- return -ENODEV;
- }
- out_8(&via[IER], IER_SET|SR_INT); /* enable interrupt from SR */
-
- return via_cuda_start();
-#endif
}
#endif /* CONFIG_ADB */
@@ -430,9 +436,11 @@
/* cuda_interrupt only takes a normal lock, we disable
* interrupts here to avoid re-entering and thus deadlocking.
*/
- disable_irq(cuda_irq);
+ if (cuda_irq)
+ disable_irq(cuda_irq);
cuda_interrupt(0, NULL);
- enable_irq(cuda_irq);
+ if (cuda_irq)
+ enable_irq(cuda_irq);
}
static irqreturn_t
@@ -446,7 +454,7 @@
spin_lock(&cuda_lock);
- /* On powermacs, this handler is registered for the VIA IRQ. But it uses
+ /* On powermacs, this handler is registered for the VIA IRQ. But they use
* just the shift register IRQ -- other VIA interrupt sources are disabled.
* On m68k macs, the VIA IRQ sources are dispatched individually. Unless
* we are polling, the shift register IRQ flag has already been cleared.