diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c
index 18df6c6..7e41a95 100644
--- a/drivers/usb/host/ehci-omap.c
+++ b/drivers/usb/host/ehci-omap.c
@@ -4,9 +4,10 @@
  * Bus Glue for the EHCI controllers in OMAP3/4
  * Tested on several OMAP3 boards, and OMAP4 Pandaboard
  *
- * Copyright (C) 2007-2010 Texas Instruments, Inc.
+ * Copyright (C) 2007-2011 Texas Instruments, Inc.
  *	Author: Vikram Pandita <vikram.pandita@ti.com>
  *	Author: Anand Gadiyar <gadiyar@ti.com>
+ *	Author: Keshava Munegowda <keshava_mgowda@ti.com>
  *
  * Copyright (C) 2009 Nokia Corporation
  *	Contact: Felipe Balbi <felipe.balbi@nokia.com>
@@ -27,116 +28,19 @@
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307 USA
  *
- * TODO (last updated Nov 21, 2010):
+ * TODO (last updated Feb 27, 2010):
  *	- add kernel-doc
  *	- enable AUTOIDLE
  *	- add suspend/resume
- *	- move workarounds to board-files
- *	- factor out code common to OHCI
  *	- add HSIC and TLL support
  *	- convert to use hwmod and runtime PM
  */
 
 #include <linux/platform_device.h>
-#include <linux/clk.h>
-#include <linux/gpio.h>
-#include <linux/regulator/consumer.h>
 #include <linux/slab.h>
 #include <linux/usb/ulpi.h>
 #include <plat/usb.h>
 
-/*
- * OMAP USBHOST Register addresses: VIRTUAL ADDRESSES
- *	Use ehci_omap_readl()/ehci_omap_writel() functions
- */
-
-/* TLL Register Set */
-#define	OMAP_USBTLL_REVISION				(0x00)
-#define	OMAP_USBTLL_SYSCONFIG				(0x10)
-#define	OMAP_USBTLL_SYSCONFIG_CACTIVITY			(1 << 8)
-#define	OMAP_USBTLL_SYSCONFIG_SIDLEMODE			(1 << 3)
-#define	OMAP_USBTLL_SYSCONFIG_ENAWAKEUP			(1 << 2)
-#define	OMAP_USBTLL_SYSCONFIG_SOFTRESET			(1 << 1)
-#define	OMAP_USBTLL_SYSCONFIG_AUTOIDLE			(1 << 0)
-
-#define	OMAP_USBTLL_SYSSTATUS				(0x14)
-#define	OMAP_USBTLL_SYSSTATUS_RESETDONE			(1 << 0)
-
-#define	OMAP_USBTLL_IRQSTATUS				(0x18)
-#define	OMAP_USBTLL_IRQENABLE				(0x1C)
-
-#define	OMAP_TLL_SHARED_CONF				(0x30)
-#define	OMAP_TLL_SHARED_CONF_USB_90D_DDR_EN		(1 << 6)
-#define	OMAP_TLL_SHARED_CONF_USB_180D_SDR_EN		(1 << 5)
-#define	OMAP_TLL_SHARED_CONF_USB_DIVRATION		(1 << 2)
-#define	OMAP_TLL_SHARED_CONF_FCLK_REQ			(1 << 1)
-#define	OMAP_TLL_SHARED_CONF_FCLK_IS_ON			(1 << 0)
-
-#define	OMAP_TLL_CHANNEL_CONF(num)			(0x040 + 0x004 * num)
-#define	OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF		(1 << 11)
-#define	OMAP_TLL_CHANNEL_CONF_ULPI_ULPIAUTOIDLE		(1 << 10)
-#define	OMAP_TLL_CHANNEL_CONF_UTMIAUTOIDLE		(1 << 9)
-#define	OMAP_TLL_CHANNEL_CONF_ULPIDDRMODE		(1 << 8)
-#define	OMAP_TLL_CHANNEL_CONF_CHANEN			(1 << 0)
-
-#define	OMAP_TLL_ULPI_FUNCTION_CTRL(num)		(0x804 + 0x100 * num)
-#define	OMAP_TLL_ULPI_INTERFACE_CTRL(num)		(0x807 + 0x100 * num)
-#define	OMAP_TLL_ULPI_OTG_CTRL(num)			(0x80A + 0x100 * num)
-#define	OMAP_TLL_ULPI_INT_EN_RISE(num)			(0x80D + 0x100 * num)
-#define	OMAP_TLL_ULPI_INT_EN_FALL(num)			(0x810 + 0x100 * num)
-#define	OMAP_TLL_ULPI_INT_STATUS(num)			(0x813 + 0x100 * num)
-#define	OMAP_TLL_ULPI_INT_LATCH(num)			(0x814 + 0x100 * num)
-#define	OMAP_TLL_ULPI_DEBUG(num)			(0x815 + 0x100 * num)
-#define	OMAP_TLL_ULPI_SCRATCH_REGISTER(num)		(0x816 + 0x100 * num)
-
-#define OMAP_TLL_CHANNEL_COUNT				3
-#define OMAP_TLL_CHANNEL_1_EN_MASK			(1 << 0)
-#define OMAP_TLL_CHANNEL_2_EN_MASK			(1 << 1)
-#define OMAP_TLL_CHANNEL_3_EN_MASK			(1 << 2)
-
-/* UHH Register Set */
-#define	OMAP_UHH_REVISION				(0x00)
-#define	OMAP_UHH_SYSCONFIG				(0x10)
-#define	OMAP_UHH_SYSCONFIG_MIDLEMODE			(1 << 12)
-#define	OMAP_UHH_SYSCONFIG_CACTIVITY			(1 << 8)
-#define	OMAP_UHH_SYSCONFIG_SIDLEMODE			(1 << 3)
-#define	OMAP_UHH_SYSCONFIG_ENAWAKEUP			(1 << 2)
-#define	OMAP_UHH_SYSCONFIG_SOFTRESET			(1 << 1)
-#define	OMAP_UHH_SYSCONFIG_AUTOIDLE			(1 << 0)
-
-#define	OMAP_UHH_SYSSTATUS				(0x14)
-#define	OMAP_UHH_HOSTCONFIG				(0x40)
-#define	OMAP_UHH_HOSTCONFIG_ULPI_BYPASS			(1 << 0)
-#define	OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS		(1 << 0)
-#define	OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS		(1 << 11)
-#define	OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS		(1 << 12)
-#define OMAP_UHH_HOSTCONFIG_INCR4_BURST_EN		(1 << 2)
-#define OMAP_UHH_HOSTCONFIG_INCR8_BURST_EN		(1 << 3)
-#define OMAP_UHH_HOSTCONFIG_INCR16_BURST_EN		(1 << 4)
-#define OMAP_UHH_HOSTCONFIG_INCRX_ALIGN_EN		(1 << 5)
-#define OMAP_UHH_HOSTCONFIG_P1_CONNECT_STATUS		(1 << 8)
-#define OMAP_UHH_HOSTCONFIG_P2_CONNECT_STATUS		(1 << 9)
-#define OMAP_UHH_HOSTCONFIG_P3_CONNECT_STATUS		(1 << 10)
-
-/* OMAP4-specific defines */
-#define OMAP4_UHH_SYSCONFIG_IDLEMODE_CLEAR		(3 << 2)
-#define OMAP4_UHH_SYSCONFIG_NOIDLE			(1 << 2)
-
-#define OMAP4_UHH_SYSCONFIG_STDBYMODE_CLEAR		(3 << 4)
-#define OMAP4_UHH_SYSCONFIG_NOSTDBY			(1 << 4)
-#define OMAP4_UHH_SYSCONFIG_SOFTRESET			(1 << 0)
-
-#define OMAP4_P1_MODE_CLEAR				(3 << 16)
-#define OMAP4_P1_MODE_TLL				(1 << 16)
-#define OMAP4_P1_MODE_HSIC				(3 << 16)
-#define OMAP4_P2_MODE_CLEAR				(3 << 18)
-#define OMAP4_P2_MODE_TLL				(1 << 18)
-#define OMAP4_P2_MODE_HSIC				(3 << 18)
-
-#define OMAP_REV2_TLL_CHANNEL_COUNT			2
-
-#define	OMAP_UHH_DEBUG_CSR				(0x44)
-
 /* EHCI Register Set */
 #define EHCI_INSNREG04					(0xA0)
 #define EHCI_INSNREG04_DISABLE_UNSUSPEND		(1 << 5)
@@ -148,141 +52,24 @@
 #define	EHCI_INSNREG05_ULPI_EXTREGADD_SHIFT		8
 #define	EHCI_INSNREG05_ULPI_WRDATA_SHIFT		0
 
-/* Values of UHH_REVISION - Note: these are not given in the TRM */
-#define OMAP_EHCI_REV1	0x00000010	/* OMAP3 */
-#define OMAP_EHCI_REV2	0x50700100	/* OMAP4 */
-
-#define is_omap_ehci_rev1(x)	(x->omap_ehci_rev == OMAP_EHCI_REV1)
-#define is_omap_ehci_rev2(x)	(x->omap_ehci_rev == OMAP_EHCI_REV2)
-
-#define is_ehci_phy_mode(x)	(x == OMAP_EHCI_PORT_MODE_PHY)
-#define is_ehci_tll_mode(x)	(x == OMAP_EHCI_PORT_MODE_TLL)
-#define is_ehci_hsic_mode(x)	(x == OMAP_EHCI_PORT_MODE_HSIC)
-
 /*-------------------------------------------------------------------------*/
 
-static inline void ehci_omap_writel(void __iomem *base, u32 reg, u32 val)
+static const struct hc_driver ehci_omap_hc_driver;
+
+
+static inline void ehci_write(void __iomem *base, u32 reg, u32 val)
 {
 	__raw_writel(val, base + reg);
 }
 
-static inline u32 ehci_omap_readl(void __iomem *base, u32 reg)
+static inline u32 ehci_read(void __iomem *base, u32 reg)
 {
 	return __raw_readl(base + reg);
 }
 
-static inline void ehci_omap_writeb(void __iomem *base, u8 reg, u8 val)
+static void omap_ehci_soft_phy_reset(struct platform_device *pdev, u8 port)
 {
-	__raw_writeb(val, base + reg);
-}
-
-static inline u8 ehci_omap_readb(void __iomem *base, u8 reg)
-{
-	return __raw_readb(base + reg);
-}
-
-/*-------------------------------------------------------------------------*/
-
-struct ehci_hcd_omap {
-	struct ehci_hcd		*ehci;
-	struct device		*dev;
-
-	struct clk		*usbhost_ick;
-	struct clk		*usbhost_hs_fck;
-	struct clk		*usbhost_fs_fck;
-	struct clk		*usbtll_fck;
-	struct clk		*usbtll_ick;
-	struct clk		*xclk60mhsp1_ck;
-	struct clk		*xclk60mhsp2_ck;
-	struct clk		*utmi_p1_fck;
-	struct clk		*usbhost_p1_fck;
-	struct clk		*usbtll_p1_fck;
-	struct clk		*utmi_p2_fck;
-	struct clk		*usbhost_p2_fck;
-	struct clk		*usbtll_p2_fck;
-
-	/* FIXME the following two workarounds are
-	 * board specific not silicon-specific so these
-	 * should be moved to board-file instead.
-	 *
-	 * Maybe someone from TI will know better which
-	 * board is affected and needs the workarounds
-	 * to be applied
-	 */
-
-	/* gpio for resetting phy */
-	int			reset_gpio_port[OMAP3_HS_USB_PORTS];
-
-	/* phy reset workaround */
-	int			phy_reset;
-
-	/* IP revision */
-	u32			omap_ehci_rev;
-
-	/* desired phy_mode: TLL, PHY */
-	enum usbhs_omap_port_mode	port_mode[OMAP3_HS_USB_PORTS];
-
-	void __iomem		*uhh_base;
-	void __iomem		*tll_base;
-	void __iomem		*ehci_base;
-
-	/* Regulators for USB PHYs.
-	 * Each PHY can have a separate regulator.
-	 */
-	struct regulator        *regulator[OMAP3_HS_USB_PORTS];
-};
-
-/*-------------------------------------------------------------------------*/
-
-static void omap_usb_utmi_init(struct ehci_hcd_omap *omap, u8 tll_channel_mask,
-				u8 tll_channel_count)
-{
-	unsigned reg;
-	int i;
-
-	/* Program the 3 TLL channels upfront */
-	for (i = 0; i < tll_channel_count; i++) {
-		reg = ehci_omap_readl(omap->tll_base, OMAP_TLL_CHANNEL_CONF(i));
-
-		/* Disable AutoIdle, BitStuffing and use SDR Mode */
-		reg &= ~(OMAP_TLL_CHANNEL_CONF_UTMIAUTOIDLE
-				| OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF
-				| OMAP_TLL_CHANNEL_CONF_ULPIDDRMODE);
-		ehci_omap_writel(omap->tll_base, OMAP_TLL_CHANNEL_CONF(i), reg);
-	}
-
-	/* Program Common TLL register */
-	reg = ehci_omap_readl(omap->tll_base, OMAP_TLL_SHARED_CONF);
-	reg |= (OMAP_TLL_SHARED_CONF_FCLK_IS_ON
-			| OMAP_TLL_SHARED_CONF_USB_DIVRATION
-			| OMAP_TLL_SHARED_CONF_USB_180D_SDR_EN);
-	reg &= ~OMAP_TLL_SHARED_CONF_USB_90D_DDR_EN;
-
-	ehci_omap_writel(omap->tll_base, OMAP_TLL_SHARED_CONF, reg);
-
-	/* Enable channels now */
-	for (i = 0; i < tll_channel_count; i++) {
-		reg = ehci_omap_readl(omap->tll_base, OMAP_TLL_CHANNEL_CONF(i));
-
-		/* Enable only the reg that is needed */
-		if (!(tll_channel_mask & 1<<i))
-			continue;
-
-		reg |= OMAP_TLL_CHANNEL_CONF_CHANEN;
-		ehci_omap_writel(omap->tll_base, OMAP_TLL_CHANNEL_CONF(i), reg);
-
-		ehci_omap_writeb(omap->tll_base,
-				OMAP_TLL_ULPI_SCRATCH_REGISTER(i), 0xbe);
-		dev_dbg(omap->dev, "ULPI_SCRATCH_REG[ch=%d]= 0x%02x\n",
-				i+1, ehci_omap_readb(omap->tll_base,
-				OMAP_TLL_ULPI_SCRATCH_REGISTER(i)));
-	}
-}
-
-/*-------------------------------------------------------------------------*/
-
-static void omap_ehci_soft_phy_reset(struct ehci_hcd_omap *omap, u8 port)
-{
+	struct usb_hcd	*hcd = dev_get_drvdata(&pdev->dev);
 	unsigned long timeout = jiffies + msecs_to_jiffies(1000);
 	unsigned reg = 0;
 
@@ -296,600 +83,20 @@
 		/* start ULPI access*/
 		| (1 << EHCI_INSNREG05_ULPI_CONTROL_SHIFT);
 
-	ehci_omap_writel(omap->ehci_base, EHCI_INSNREG05_ULPI, reg);
+	ehci_write(hcd->regs, EHCI_INSNREG05_ULPI, reg);
 
 	/* Wait for ULPI access completion */
-	while ((ehci_omap_readl(omap->ehci_base, EHCI_INSNREG05_ULPI)
+	while ((ehci_read(hcd->regs, EHCI_INSNREG05_ULPI)
 			& (1 << EHCI_INSNREG05_ULPI_CONTROL_SHIFT))) {
 		cpu_relax();
 
 		if (time_after(jiffies, timeout)) {
-			dev_dbg(omap->dev, "phy reset operation timed out\n");
+			dev_dbg(&pdev->dev, "phy reset operation timed out\n");
 			break;
 		}
 	}
 }
 
-/* omap_start_ehc
- *	- Start the TI USBHOST controller
- */
-static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
-{
-	unsigned long timeout = jiffies + msecs_to_jiffies(1000);
-	u8 tll_ch_mask = 0;
-	unsigned reg = 0;
-	int ret = 0;
-
-	dev_dbg(omap->dev, "starting TI EHCI USB Controller\n");
-
-	/* Enable Clocks for USBHOST */
-	omap->usbhost_ick = clk_get(omap->dev, "usbhost_ick");
-	if (IS_ERR(omap->usbhost_ick)) {
-		ret =  PTR_ERR(omap->usbhost_ick);
-		goto err_host_ick;
-	}
-	clk_enable(omap->usbhost_ick);
-
-	omap->usbhost_hs_fck = clk_get(omap->dev, "hs_fck");
-	if (IS_ERR(omap->usbhost_hs_fck)) {
-		ret = PTR_ERR(omap->usbhost_hs_fck);
-		goto err_host_120m_fck;
-	}
-	clk_enable(omap->usbhost_hs_fck);
-
-	omap->usbhost_fs_fck = clk_get(omap->dev, "fs_fck");
-	if (IS_ERR(omap->usbhost_fs_fck)) {
-		ret = PTR_ERR(omap->usbhost_fs_fck);
-		goto err_host_48m_fck;
-	}
-	clk_enable(omap->usbhost_fs_fck);
-
-	if (omap->phy_reset) {
-		/* Refer: ISSUE1 */
-		if (gpio_is_valid(omap->reset_gpio_port[0])) {
-			gpio_request(omap->reset_gpio_port[0],
-						"USB1 PHY reset");
-			gpio_direction_output(omap->reset_gpio_port[0], 0);
-		}
-
-		if (gpio_is_valid(omap->reset_gpio_port[1])) {
-			gpio_request(omap->reset_gpio_port[1],
-						"USB2 PHY reset");
-			gpio_direction_output(omap->reset_gpio_port[1], 0);
-		}
-
-		/* Hold the PHY in RESET for enough time till DIR is high */
-		udelay(10);
-	}
-
-	/* Configure TLL for 60Mhz clk for ULPI */
-	omap->usbtll_fck = clk_get(omap->dev, "usbtll_fck");
-	if (IS_ERR(omap->usbtll_fck)) {
-		ret = PTR_ERR(omap->usbtll_fck);
-		goto err_tll_fck;
-	}
-	clk_enable(omap->usbtll_fck);
-
-	omap->usbtll_ick = clk_get(omap->dev, "usbtll_ick");
-	if (IS_ERR(omap->usbtll_ick)) {
-		ret = PTR_ERR(omap->usbtll_ick);
-		goto err_tll_ick;
-	}
-	clk_enable(omap->usbtll_ick);
-
-	omap->omap_ehci_rev = ehci_omap_readl(omap->uhh_base,
-						OMAP_UHH_REVISION);
-	dev_dbg(omap->dev, "OMAP UHH_REVISION 0x%x\n",
-					omap->omap_ehci_rev);
-
-	/*
-	 * Enable per-port clocks as needed (newer controllers only).
-	 * - External ULPI clock for PHY mode
-	 * - Internal clocks for TLL and HSIC modes (TODO)
-	 */
-	if (is_omap_ehci_rev2(omap)) {
-		switch (omap->port_mode[0]) {
-		case OMAP_EHCI_PORT_MODE_PHY:
-			omap->xclk60mhsp1_ck = clk_get(omap->dev,
-							"xclk60mhsp1_ck");
-			if (IS_ERR(omap->xclk60mhsp1_ck)) {
-				ret = PTR_ERR(omap->xclk60mhsp1_ck);
-				dev_err(omap->dev,
-					"Unable to get Port1 ULPI clock\n");
-			}
-
-			omap->utmi_p1_fck = clk_get(omap->dev,
-							"utmi_p1_gfclk");
-			if (IS_ERR(omap->utmi_p1_fck)) {
-				ret = PTR_ERR(omap->utmi_p1_fck);
-				dev_err(omap->dev,
-					"Unable to get utmi_p1_fck\n");
-			}
-
-			ret = clk_set_parent(omap->utmi_p1_fck,
-						omap->xclk60mhsp1_ck);
-			if (ret != 0) {
-				dev_err(omap->dev,
-					"Unable to set P1 f-clock\n");
-			}
-			break;
-		case OMAP_EHCI_PORT_MODE_TLL:
-			omap->xclk60mhsp1_ck = clk_get(omap->dev,
-							"init_60m_fclk");
-			if (IS_ERR(omap->xclk60mhsp1_ck)) {
-				ret = PTR_ERR(omap->xclk60mhsp1_ck);
-				dev_err(omap->dev,
-					"Unable to get Port1 ULPI clock\n");
-			}
-
-			omap->utmi_p1_fck = clk_get(omap->dev,
-							"utmi_p1_gfclk");
-			if (IS_ERR(omap->utmi_p1_fck)) {
-				ret = PTR_ERR(omap->utmi_p1_fck);
-				dev_err(omap->dev,
-					"Unable to get utmi_p1_fck\n");
-			}
-
-			ret = clk_set_parent(omap->utmi_p1_fck,
-						omap->xclk60mhsp1_ck);
-			if (ret != 0) {
-				dev_err(omap->dev,
-					"Unable to set P1 f-clock\n");
-			}
-
-			omap->usbhost_p1_fck = clk_get(omap->dev,
-						"usb_host_hs_utmi_p1_clk");
-			if (IS_ERR(omap->usbhost_p1_fck)) {
-				ret = PTR_ERR(omap->usbhost_p1_fck);
-				dev_err(omap->dev,
-					"Unable to get HOST PORT 1 clk\n");
-			} else {
-				clk_enable(omap->usbhost_p1_fck);
-			}
-
-			omap->usbtll_p1_fck = clk_get(omap->dev,
-						"usb_tll_hs_usb_ch0_clk");
-
-			if (IS_ERR(omap->usbtll_p1_fck)) {
-				ret = PTR_ERR(omap->usbtll_p1_fck);
-				dev_err(omap->dev,
-					"Unable to get TLL CH0 clk\n");
-			} else {
-				clk_enable(omap->usbtll_p1_fck);
-			}
-			break;
-			/* TODO */
-		default:
-			break;
-		}
-		switch (omap->port_mode[1]) {
-		case OMAP_EHCI_PORT_MODE_PHY:
-			omap->xclk60mhsp2_ck = clk_get(omap->dev,
-							"xclk60mhsp2_ck");
-			if (IS_ERR(omap->xclk60mhsp2_ck)) {
-				ret = PTR_ERR(omap->xclk60mhsp2_ck);
-				dev_err(omap->dev,
-					"Unable to get Port2 ULPI clock\n");
-			}
-
-			omap->utmi_p2_fck = clk_get(omap->dev,
-							"utmi_p2_gfclk");
-			if (IS_ERR(omap->utmi_p2_fck)) {
-				ret = PTR_ERR(omap->utmi_p2_fck);
-				dev_err(omap->dev,
-					"Unable to get utmi_p2_fck\n");
-			}
-
-			ret = clk_set_parent(omap->utmi_p2_fck,
-						omap->xclk60mhsp2_ck);
-			if (ret != 0) {
-				dev_err(omap->dev,
-					"Unable to set P2 f-clock\n");
-			}
-			break;
-		case OMAP_EHCI_PORT_MODE_TLL:
-			omap->xclk60mhsp2_ck = clk_get(omap->dev,
-							"init_60m_fclk");
-			if (IS_ERR(omap->xclk60mhsp2_ck)) {
-				ret = PTR_ERR(omap->xclk60mhsp2_ck);
-				dev_err(omap->dev,
-					"Unable to get Port2 ULPI clock\n");
-			}
-
-			omap->utmi_p2_fck = clk_get(omap->dev,
-							"utmi_p2_gfclk");
-			if (IS_ERR(omap->utmi_p2_fck)) {
-				ret = PTR_ERR(omap->utmi_p2_fck);
-				dev_err(omap->dev,
-					"Unable to get utmi_p2_fck\n");
-			}
-
-			ret = clk_set_parent(omap->utmi_p2_fck,
-						omap->xclk60mhsp2_ck);
-			if (ret != 0) {
-				dev_err(omap->dev,
-					"Unable to set P2 f-clock\n");
-			}
-
-			omap->usbhost_p2_fck = clk_get(omap->dev,
-						"usb_host_hs_utmi_p2_clk");
-			if (IS_ERR(omap->usbhost_p2_fck)) {
-				ret = PTR_ERR(omap->usbhost_p2_fck);
-				dev_err(omap->dev,
-					"Unable to get HOST PORT 2 clk\n");
-			} else {
-				clk_enable(omap->usbhost_p2_fck);
-			}
-
-			omap->usbtll_p2_fck = clk_get(omap->dev,
-						"usb_tll_hs_usb_ch1_clk");
-
-			if (IS_ERR(omap->usbtll_p2_fck)) {
-				ret = PTR_ERR(omap->usbtll_p2_fck);
-				dev_err(omap->dev,
-					"Unable to get TLL CH1 clk\n");
-			} else {
-				clk_enable(omap->usbtll_p2_fck);
-			}
-			break;
-			/* TODO */
-		default:
-			break;
-		}
-	}
-
-
-	/* perform TLL soft reset, and wait until reset is complete */
-	ehci_omap_writel(omap->tll_base, OMAP_USBTLL_SYSCONFIG,
-			OMAP_USBTLL_SYSCONFIG_SOFTRESET);
-
-	/* Wait for TLL reset to complete */
-	while (!(ehci_omap_readl(omap->tll_base, OMAP_USBTLL_SYSSTATUS)
-			& OMAP_USBTLL_SYSSTATUS_RESETDONE)) {
-		cpu_relax();
-
-		if (time_after(jiffies, timeout)) {
-			dev_dbg(omap->dev, "operation timed out\n");
-			ret = -EINVAL;
-			goto err_sys_status;
-		}
-	}
-
-	dev_dbg(omap->dev, "TLL RESET DONE\n");
-
-	/* (1<<3) = no idle mode only for initial debugging */
-	ehci_omap_writel(omap->tll_base, OMAP_USBTLL_SYSCONFIG,
-			OMAP_USBTLL_SYSCONFIG_ENAWAKEUP |
-			OMAP_USBTLL_SYSCONFIG_SIDLEMODE |
-			OMAP_USBTLL_SYSCONFIG_CACTIVITY);
-
-
-	/* Put UHH in NoIdle/NoStandby mode */
-	reg = ehci_omap_readl(omap->uhh_base, OMAP_UHH_SYSCONFIG);
-	if (is_omap_ehci_rev1(omap)) {
-		reg |= (OMAP_UHH_SYSCONFIG_ENAWAKEUP
-				| OMAP_UHH_SYSCONFIG_SIDLEMODE
-				| OMAP_UHH_SYSCONFIG_CACTIVITY
-				| OMAP_UHH_SYSCONFIG_MIDLEMODE);
-		reg &= ~OMAP_UHH_SYSCONFIG_AUTOIDLE;
-
-
-	} else if (is_omap_ehci_rev2(omap)) {
-		reg &= ~OMAP4_UHH_SYSCONFIG_IDLEMODE_CLEAR;
-		reg |= OMAP4_UHH_SYSCONFIG_NOIDLE;
-		reg &= ~OMAP4_UHH_SYSCONFIG_STDBYMODE_CLEAR;
-		reg |= OMAP4_UHH_SYSCONFIG_NOSTDBY;
-	}
-	ehci_omap_writel(omap->uhh_base, OMAP_UHH_SYSCONFIG, reg);
-
-	reg = ehci_omap_readl(omap->uhh_base, OMAP_UHH_HOSTCONFIG);
-
-	/* setup ULPI bypass and burst configurations */
-	reg |= (OMAP_UHH_HOSTCONFIG_INCR4_BURST_EN
-			| OMAP_UHH_HOSTCONFIG_INCR8_BURST_EN
-			| OMAP_UHH_HOSTCONFIG_INCR16_BURST_EN);
-	reg &= ~OMAP_UHH_HOSTCONFIG_INCRX_ALIGN_EN;
-
-	if (is_omap_ehci_rev1(omap)) {
-		if (omap->port_mode[0] == OMAP_USBHS_PORT_MODE_UNUSED)
-			reg &= ~OMAP_UHH_HOSTCONFIG_P1_CONNECT_STATUS;
-		if (omap->port_mode[1] == OMAP_USBHS_PORT_MODE_UNUSED)
-			reg &= ~OMAP_UHH_HOSTCONFIG_P2_CONNECT_STATUS;
-		if (omap->port_mode[2] == OMAP_USBHS_PORT_MODE_UNUSED)
-			reg &= ~OMAP_UHH_HOSTCONFIG_P3_CONNECT_STATUS;
-
-		/* Bypass the TLL module for PHY mode operation */
-		if (cpu_is_omap3430() && (omap_rev() <= OMAP3430_REV_ES2_1)) {
-			dev_dbg(omap->dev, "OMAP3 ES version <= ES2.1\n");
-			if (is_ehci_phy_mode(omap->port_mode[0]) ||
-				is_ehci_phy_mode(omap->port_mode[1]) ||
-					is_ehci_phy_mode(omap->port_mode[2]))
-				reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_BYPASS;
-			else
-				reg |= OMAP_UHH_HOSTCONFIG_ULPI_BYPASS;
-		} else {
-			dev_dbg(omap->dev, "OMAP3 ES version > ES2.1\n");
-			if (is_ehci_phy_mode(omap->port_mode[0]))
-				reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS;
-			else if (is_ehci_tll_mode(omap->port_mode[0]))
-				reg |= OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS;
-
-			if (is_ehci_phy_mode(omap->port_mode[1]))
-				reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS;
-			else if (is_ehci_tll_mode(omap->port_mode[1]))
-				reg |= OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS;
-
-			if (is_ehci_phy_mode(omap->port_mode[2]))
-				reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS;
-			else if (is_ehci_tll_mode(omap->port_mode[2]))
-				reg |= OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS;
-		}
-	} else if (is_omap_ehci_rev2(omap)) {
-		/* Clear port mode fields for PHY mode*/
-		reg &= ~OMAP4_P1_MODE_CLEAR;
-		reg &= ~OMAP4_P2_MODE_CLEAR;
-
-		if (is_ehci_tll_mode(omap->port_mode[0]))
-			reg |= OMAP4_P1_MODE_TLL;
-		else if (is_ehci_hsic_mode(omap->port_mode[0]))
-			reg |= OMAP4_P1_MODE_HSIC;
-
-		if (is_ehci_tll_mode(omap->port_mode[1]))
-			reg |= OMAP4_P2_MODE_TLL;
-		else if (is_ehci_hsic_mode(omap->port_mode[1]))
-			reg |= OMAP4_P2_MODE_HSIC;
-	}
-
-	ehci_omap_writel(omap->uhh_base, OMAP_UHH_HOSTCONFIG, reg);
-	dev_dbg(omap->dev, "UHH setup done, uhh_hostconfig=%x\n", reg);
-
-
-	/*
-	 * An undocumented "feature" in the OMAP3 EHCI controller,
-	 * causes suspended ports to be taken out of suspend when
-	 * the USBCMD.Run/Stop bit is cleared (for example when
-	 * we do ehci_bus_suspend).
-	 * This breaks suspend-resume if the root-hub is allowed
-	 * to suspend. Writing 1 to this undocumented register bit
-	 * disables this feature and restores normal behavior.
-	 */
-	ehci_omap_writel(omap->ehci_base, EHCI_INSNREG04,
-				EHCI_INSNREG04_DISABLE_UNSUSPEND);
-
-	if ((omap->port_mode[0] == OMAP_EHCI_PORT_MODE_TLL) ||
-		(omap->port_mode[1] == OMAP_EHCI_PORT_MODE_TLL) ||
-			(omap->port_mode[2] == OMAP_EHCI_PORT_MODE_TLL)) {
-
-		if (omap->port_mode[0] == OMAP_EHCI_PORT_MODE_TLL)
-			tll_ch_mask |= OMAP_TLL_CHANNEL_1_EN_MASK;
-		if (omap->port_mode[1] == OMAP_EHCI_PORT_MODE_TLL)
-			tll_ch_mask |= OMAP_TLL_CHANNEL_2_EN_MASK;
-		if (omap->port_mode[2] == OMAP_EHCI_PORT_MODE_TLL)
-			tll_ch_mask |= OMAP_TLL_CHANNEL_3_EN_MASK;
-
-		/* Enable UTMI mode for required TLL channels */
-		omap_usb_utmi_init(omap, tll_ch_mask, OMAP_TLL_CHANNEL_COUNT);
-	}
-
-	if (omap->phy_reset) {
-		/* Refer ISSUE1:
-		 * Hold the PHY in RESET for enough time till
-		 * PHY is settled and ready
-		 */
-		udelay(10);
-
-		if (gpio_is_valid(omap->reset_gpio_port[0]))
-			gpio_set_value(omap->reset_gpio_port[0], 1);
-
-		if (gpio_is_valid(omap->reset_gpio_port[1]))
-			gpio_set_value(omap->reset_gpio_port[1], 1);
-	}
-
-	/* Soft reset the PHY using PHY reset command over ULPI */
-	if (omap->port_mode[0] == OMAP_EHCI_PORT_MODE_PHY)
-		omap_ehci_soft_phy_reset(omap, 0);
-	if (omap->port_mode[1] == OMAP_EHCI_PORT_MODE_PHY)
-		omap_ehci_soft_phy_reset(omap, 1);
-
-	return 0;
-
-err_sys_status:
-
-	if (omap->usbtll_p2_fck != NULL) {
-		clk_disable(omap->usbtll_p2_fck);
-		clk_put(omap->usbtll_p2_fck);
-	}
-	if (omap->usbhost_p2_fck != NULL) {
-		clk_disable(omap->usbhost_p2_fck);
-		clk_put(omap->usbhost_p2_fck);
-	}
-	if (omap->usbtll_p1_fck != NULL) {
-		clk_disable(omap->usbtll_p1_fck);
-		clk_put(omap->usbtll_p1_fck);
-	}
-	if (omap->usbhost_p1_fck != NULL) {
-		clk_disable(omap->usbhost_p1_fck);
-		clk_put(omap->usbhost_p1_fck);
-	}
-
-	clk_disable(omap->utmi_p2_fck);
-	clk_put(omap->utmi_p2_fck);
-	clk_disable(omap->xclk60mhsp2_ck);
-	clk_put(omap->xclk60mhsp2_ck);
-	clk_disable(omap->utmi_p1_fck);
-	clk_put(omap->utmi_p1_fck);
-	clk_disable(omap->xclk60mhsp1_ck);
-	clk_put(omap->xclk60mhsp1_ck);
-	clk_disable(omap->usbtll_ick);
-	clk_put(omap->usbtll_ick);
-
-err_tll_ick:
-	clk_disable(omap->usbtll_fck);
-	clk_put(omap->usbtll_fck);
-
-err_tll_fck:
-	clk_disable(omap->usbhost_fs_fck);
-	clk_put(omap->usbhost_fs_fck);
-
-	if (omap->phy_reset) {
-		if (gpio_is_valid(omap->reset_gpio_port[0]))
-			gpio_free(omap->reset_gpio_port[0]);
-
-		if (gpio_is_valid(omap->reset_gpio_port[1]))
-			gpio_free(omap->reset_gpio_port[1]);
-	}
-
-err_host_48m_fck:
-	clk_disable(omap->usbhost_hs_fck);
-	clk_put(omap->usbhost_hs_fck);
-
-err_host_120m_fck:
-	clk_disable(omap->usbhost_ick);
-	clk_put(omap->usbhost_ick);
-
-err_host_ick:
-	return ret;
-}
-
-static void omap_stop_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
-{
-	unsigned long timeout = jiffies + msecs_to_jiffies(100);
-
-	dev_dbg(omap->dev, "stopping TI EHCI USB Controller\n");
-
-	/* Reset OMAP modules for insmod/rmmod to work */
-	ehci_omap_writel(omap->uhh_base, OMAP_UHH_SYSCONFIG,
-			is_omap_ehci_rev2(omap) ?
-			OMAP4_UHH_SYSCONFIG_SOFTRESET :
-			OMAP_UHH_SYSCONFIG_SOFTRESET);
-	while (!(ehci_omap_readl(omap->uhh_base, OMAP_UHH_SYSSTATUS)
-				& (1 << 0))) {
-		cpu_relax();
-
-		if (time_after(jiffies, timeout))
-			dev_dbg(omap->dev, "operation timed out\n");
-	}
-
-	while (!(ehci_omap_readl(omap->uhh_base, OMAP_UHH_SYSSTATUS)
-				& (1 << 1))) {
-		cpu_relax();
-
-		if (time_after(jiffies, timeout))
-			dev_dbg(omap->dev, "operation timed out\n");
-	}
-
-	while (!(ehci_omap_readl(omap->uhh_base, OMAP_UHH_SYSSTATUS)
-				& (1 << 2))) {
-		cpu_relax();
-
-		if (time_after(jiffies, timeout))
-			dev_dbg(omap->dev, "operation timed out\n");
-	}
-
-	ehci_omap_writel(omap->tll_base, OMAP_USBTLL_SYSCONFIG, (1 << 1));
-
-	while (!(ehci_omap_readl(omap->tll_base, OMAP_USBTLL_SYSSTATUS)
-				& (1 << 0))) {
-		cpu_relax();
-
-		if (time_after(jiffies, timeout))
-			dev_dbg(omap->dev, "operation timed out\n");
-	}
-
-	if (omap->usbtll_fck != NULL) {
-		clk_disable(omap->usbtll_fck);
-		clk_put(omap->usbtll_fck);
-		omap->usbtll_fck = NULL;
-	}
-
-	if (omap->usbhost_ick != NULL) {
-		clk_disable(omap->usbhost_ick);
-		clk_put(omap->usbhost_ick);
-		omap->usbhost_ick = NULL;
-	}
-
-	if (omap->usbhost_fs_fck != NULL) {
-		clk_disable(omap->usbhost_fs_fck);
-		clk_put(omap->usbhost_fs_fck);
-		omap->usbhost_fs_fck = NULL;
-	}
-
-	if (omap->usbhost_hs_fck != NULL) {
-		clk_disable(omap->usbhost_hs_fck);
-		clk_put(omap->usbhost_hs_fck);
-		omap->usbhost_hs_fck = NULL;
-	}
-
-	if (omap->usbtll_ick != NULL) {
-		clk_disable(omap->usbtll_ick);
-		clk_put(omap->usbtll_ick);
-		omap->usbtll_ick = NULL;
-	}
-
-	if (is_omap_ehci_rev2(omap)) {
-		if (omap->xclk60mhsp1_ck != NULL) {
-			clk_disable(omap->xclk60mhsp1_ck);
-			clk_put(omap->xclk60mhsp1_ck);
-			omap->xclk60mhsp1_ck = NULL;
-		}
-
-		if (omap->utmi_p1_fck != NULL) {
-			clk_disable(omap->utmi_p1_fck);
-			clk_put(omap->utmi_p1_fck);
-			omap->utmi_p1_fck = NULL;
-		}
-
-		if (omap->xclk60mhsp2_ck != NULL) {
-			clk_disable(omap->xclk60mhsp2_ck);
-			clk_put(omap->xclk60mhsp2_ck);
-			omap->xclk60mhsp2_ck = NULL;
-		}
-
-		if (omap->utmi_p2_fck != NULL) {
-			clk_disable(omap->utmi_p2_fck);
-			clk_put(omap->utmi_p2_fck);
-			omap->utmi_p2_fck = NULL;
-		}
-
-		if (omap->usbtll_p2_fck != NULL) {
-			clk_disable(omap->usbtll_p2_fck);
-			clk_put(omap->usbtll_p2_fck);
-			omap->usbtll_p2_fck = NULL;
-		}
-
-		if (omap->usbhost_p2_fck != NULL) {
-			clk_disable(omap->usbhost_p2_fck);
-			clk_put(omap->usbhost_p2_fck);
-			omap->usbhost_p2_fck = NULL;
-		}
-
-		if (omap->usbtll_p1_fck != NULL) {
-			clk_disable(omap->usbtll_p1_fck);
-			clk_put(omap->usbtll_p1_fck);
-			omap->usbtll_p1_fck = NULL;
-		}
-
-		if (omap->usbhost_p1_fck != NULL) {
-			clk_disable(omap->usbhost_p1_fck);
-			clk_put(omap->usbhost_p1_fck);
-			omap->usbhost_p1_fck = NULL;
-		}
-	}
-
-	if (omap->phy_reset) {
-		if (gpio_is_valid(omap->reset_gpio_port[0]))
-			gpio_free(omap->reset_gpio_port[0]);
-
-		if (gpio_is_valid(omap->reset_gpio_port[1]))
-			gpio_free(omap->reset_gpio_port[1]);
-	}
-
-	dev_dbg(omap->dev, "Clock to USB host has been disabled\n");
-}
-
-/*-------------------------------------------------------------------------*/
-
-static const struct hc_driver ehci_omap_hc_driver;
 
 /* configure so an HC device and id are always provided */
 /* always called with process context; sleeping is OK */
@@ -903,155 +110,113 @@
  */
 static int ehci_hcd_omap_probe(struct platform_device *pdev)
 {
-	struct usbhs_omap_board_data *pdata = pdev->dev.platform_data;
-	struct ehci_hcd_omap *omap;
-	struct resource *res;
-	struct usb_hcd *hcd;
-
-	int irq = platform_get_irq(pdev, 0);
-	int ret = -ENODEV;
-	int i;
-	char supply[7];
-
-	if (!pdata) {
-		dev_dbg(&pdev->dev, "missing platform_data\n");
-		goto err_pdata;
-	}
+	struct device				*dev = &pdev->dev;
+	struct ehci_hcd_omap_platform_data	*pdata = dev->platform_data;
+	struct resource				*res;
+	struct usb_hcd				*hcd;
+	void __iomem				*regs;
+	struct ehci_hcd				*omap_ehci;
+	int					ret = -ENODEV;
+	int					irq;
 
 	if (usb_disabled())
-		goto err_disabled;
+		return -ENODEV;
 
-	omap = kzalloc(sizeof(*omap), GFP_KERNEL);
-	if (!omap) {
-		ret = -ENOMEM;
-		goto err_disabled;
+	if (!dev->parent) {
+		dev_err(dev, "Missing parent device\n");
+		return -ENODEV;
 	}
 
-	hcd = usb_create_hcd(&ehci_omap_hc_driver, &pdev->dev,
-			dev_name(&pdev->dev));
+	irq = platform_get_irq_byname(pdev, "ehci-irq");
+	if (irq < 0) {
+		dev_err(dev, "EHCI irq failed\n");
+		return -ENODEV;
+	}
+
+	res =  platform_get_resource_byname(pdev,
+				IORESOURCE_MEM, "ehci");
+	if (!res) {
+		dev_err(dev, "UHH EHCI get resource failed\n");
+		return -ENODEV;
+	}
+
+	regs = ioremap(res->start, resource_size(res));
+	if (!regs) {
+		dev_err(dev, "UHH EHCI ioremap failed\n");
+		return -ENOMEM;
+	}
+
+	hcd = usb_create_hcd(&ehci_omap_hc_driver, dev,
+			dev_name(dev));
 	if (!hcd) {
-		dev_err(&pdev->dev, "failed to create hcd with err %d\n", ret);
+		dev_err(dev, "failed to create hcd with err %d\n", ret);
 		ret = -ENOMEM;
-		goto err_create_hcd;
+		goto err_io;
 	}
 
-	platform_set_drvdata(pdev, omap);
-	omap->dev		= &pdev->dev;
-	omap->phy_reset		= pdata->phy_reset;
-	omap->reset_gpio_port[0]	= pdata->reset_gpio_port[0];
-	omap->reset_gpio_port[1]	= pdata->reset_gpio_port[1];
-	omap->reset_gpio_port[2]	= pdata->reset_gpio_port[2];
-	omap->port_mode[0]		= pdata->port_mode[0];
-	omap->port_mode[1]		= pdata->port_mode[1];
-	omap->port_mode[2]		= pdata->port_mode[2];
-	omap->ehci		= hcd_to_ehci(hcd);
-	omap->ehci->sbrn	= 0x20;
-
-	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ehci");
-
 	hcd->rsrc_start = res->start;
 	hcd->rsrc_len = resource_size(res);
+	hcd->regs = regs;
 
-	hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
-	if (!hcd->regs) {
-		dev_err(&pdev->dev, "EHCI ioremap failed\n");
-		ret = -ENOMEM;
-		goto err_ioremap;
+	ret = omap_usbhs_enable(dev);
+	if (ret) {
+		dev_err(dev, "failed to start usbhs with err %d\n", ret);
+		goto err_enable;
 	}
 
+	/*
+	 * An undocumented "feature" in the OMAP3 EHCI controller,
+	 * causes suspended ports to be taken out of suspend when
+	 * the USBCMD.Run/Stop bit is cleared (for example when
+	 * we do ehci_bus_suspend).
+	 * This breaks suspend-resume if the root-hub is allowed
+	 * to suspend. Writing 1 to this undocumented register bit
+	 * disables this feature and restores normal behavior.
+	 */
+	ehci_write(regs, EHCI_INSNREG04,
+				EHCI_INSNREG04_DISABLE_UNSUSPEND);
+
+	/* Soft reset the PHY using PHY reset command over ULPI */
+	if (pdata->port_mode[0] == OMAP_EHCI_PORT_MODE_PHY)
+		omap_ehci_soft_phy_reset(pdev, 0);
+	if (pdata->port_mode[1] == OMAP_EHCI_PORT_MODE_PHY)
+		omap_ehci_soft_phy_reset(pdev, 1);
+
+	omap_ehci = hcd_to_ehci(hcd);
+	omap_ehci->sbrn = 0x20;
+
 	/* we know this is the memory we want, no need to ioremap again */
-	omap->ehci->caps = hcd->regs;
-	omap->ehci_base = hcd->regs;
+	omap_ehci->caps = hcd->regs;
+	omap_ehci->regs = hcd->regs
+			+ HC_LENGTH(readl(&omap_ehci->caps->hc_capbase));
 
-	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "uhh");
-	omap->uhh_base = ioremap(res->start, resource_size(res));
-	if (!omap->uhh_base) {
-		dev_err(&pdev->dev, "UHH ioremap failed\n");
-		ret = -ENOMEM;
-		goto err_uhh_ioremap;
-	}
-
-	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "tll");
-	omap->tll_base = ioremap(res->start, resource_size(res));
-	if (!omap->tll_base) {
-		dev_err(&pdev->dev, "TLL ioremap failed\n");
-		ret = -ENOMEM;
-		goto err_tll_ioremap;
-	}
-
-	/* get ehci regulator and enable */
-	for (i = 0 ; i < OMAP3_HS_USB_PORTS ; i++) {
-		if (omap->port_mode[i] != OMAP_EHCI_PORT_MODE_PHY) {
-			omap->regulator[i] = NULL;
-			continue;
-		}
-		snprintf(supply, sizeof(supply), "hsusb%d", i);
-		omap->regulator[i] = regulator_get(omap->dev, supply);
-		if (IS_ERR(omap->regulator[i])) {
-			omap->regulator[i] = NULL;
-			dev_dbg(&pdev->dev,
-			"failed to get ehci port%d regulator\n", i);
-		} else {
-			regulator_enable(omap->regulator[i]);
-		}
-	}
-
-	ret = omap_start_ehc(omap, hcd);
-	if (ret) {
-		dev_err(&pdev->dev, "failed to start ehci with err %d\n", ret);
-		goto err_start;
-	}
-
-	omap->ehci->regs = hcd->regs
-		+ HC_LENGTH(readl(&omap->ehci->caps->hc_capbase));
-
-	dbg_hcs_params(omap->ehci, "reset");
-	dbg_hcc_params(omap->ehci, "reset");
+	dbg_hcs_params(omap_ehci, "reset");
+	dbg_hcc_params(omap_ehci, "reset");
 
 	/* cache this readonly data; minimize chip reads */
-	omap->ehci->hcs_params = readl(&omap->ehci->caps->hcs_params);
+	omap_ehci->hcs_params = readl(&omap_ehci->caps->hcs_params);
 
 	ret = usb_add_hcd(hcd, irq, IRQF_DISABLED | IRQF_SHARED);
 	if (ret) {
-		dev_err(&pdev->dev, "failed to add hcd with err %d\n", ret);
+		dev_err(dev, "failed to add hcd with err %d\n", ret);
 		goto err_add_hcd;
 	}
 
 	/* root ports should always stay powered */
-	ehci_port_power(omap->ehci, 1);
+	ehci_port_power(omap_ehci, 1);
 
 	return 0;
 
 err_add_hcd:
-	omap_stop_ehc(omap, hcd);
+	omap_usbhs_disable(dev);
 
-err_start:
-	for (i = 0 ; i < OMAP3_HS_USB_PORTS ; i++) {
-		if (omap->regulator[i]) {
-			regulator_disable(omap->regulator[i]);
-			regulator_put(omap->regulator[i]);
-		}
-	}
-	iounmap(omap->tll_base);
-
-err_tll_ioremap:
-	iounmap(omap->uhh_base);
-
-err_uhh_ioremap:
-	iounmap(hcd->regs);
-
-err_ioremap:
+err_enable:
 	usb_put_hcd(hcd);
 
-err_create_hcd:
-	kfree(omap);
-err_disabled:
-err_pdata:
+err_io:
 	return ret;
 }
 
-/* may be called without controller electrically present */
-/* may be called with controller, bus, and devices active */
 
 /**
  * ehci_hcd_omap_remove - shutdown processing for EHCI HCDs
@@ -1063,31 +228,18 @@
  */
 static int ehci_hcd_omap_remove(struct platform_device *pdev)
 {
-	struct ehci_hcd_omap *omap = platform_get_drvdata(pdev);
-	struct usb_hcd *hcd = ehci_to_hcd(omap->ehci);
-	int i;
+	struct device *dev	= &pdev->dev;
+	struct usb_hcd *hcd	= dev_get_drvdata(dev);
 
 	usb_remove_hcd(hcd);
-	omap_stop_ehc(omap, hcd);
-	iounmap(hcd->regs);
-	for (i = 0 ; i < OMAP3_HS_USB_PORTS ; i++) {
-		if (omap->regulator[i]) {
-			regulator_disable(omap->regulator[i]);
-			regulator_put(omap->regulator[i]);
-		}
-	}
-	iounmap(omap->tll_base);
-	iounmap(omap->uhh_base);
+	omap_usbhs_disable(dev);
 	usb_put_hcd(hcd);
-	kfree(omap);
-
 	return 0;
 }
 
 static void ehci_hcd_omap_shutdown(struct platform_device *pdev)
 {
-	struct ehci_hcd_omap *omap = platform_get_drvdata(pdev);
-	struct usb_hcd *hcd = ehci_to_hcd(omap->ehci);
+	struct usb_hcd *hcd = dev_get_drvdata(&pdev->dev);
 
 	if (hcd->driver->shutdown)
 		hcd->driver->shutdown(hcd);
diff --git a/drivers/usb/host/ohci-omap3.c b/drivers/usb/host/ohci-omap3.c
index 3f9db87..6048f2f 100644
--- a/drivers/usb/host/ohci-omap3.c
+++ b/drivers/usb/host/ohci-omap3.c
@@ -7,6 +7,7 @@
  * Copyright (C) 2007-2010 Texas Instruments, Inc.
  * Author: Vikram Pandita <vikram.pandita@ti.com>
  * Author: Anand Gadiyar <gadiyar@ti.com>
+ * Author: Keshava Munegowda <keshava_mgowda@ti.com>
  *
  * Based on ehci-omap.c and some other ohci glue layers
  *
@@ -24,150 +25,15 @@
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307 USA
  *
- * TODO (last updated Mar 10th, 2010):
+ * TODO (last updated Feb 27, 2011):
  *	- add kernel-doc
- *	- Factor out code common to EHCI to a separate file
- *	- Make EHCI and OHCI coexist together
- *	  - needs newer silicon versions to actually work
- *	  - the last one to be loaded currently steps on the other's toes
- *	- Add hooks for configuring transceivers, etc. at init/exit
- *	- Add aggressive clock-management code
  */
 
 #include <linux/platform_device.h>
-#include <linux/clk.h>
-
 #include <plat/usb.h>
 
-/*
- * OMAP USBHOST Register addresses: VIRTUAL ADDRESSES
- *	Use ohci_omap_readl()/ohci_omap_writel() functions
- */
-
-/* TLL Register Set */
-#define	OMAP_USBTLL_REVISION				(0x00)
-#define	OMAP_USBTLL_SYSCONFIG				(0x10)
-#define	OMAP_USBTLL_SYSCONFIG_CACTIVITY			(1 << 8)
-#define	OMAP_USBTLL_SYSCONFIG_SIDLEMODE			(1 << 3)
-#define	OMAP_USBTLL_SYSCONFIG_ENAWAKEUP			(1 << 2)
-#define	OMAP_USBTLL_SYSCONFIG_SOFTRESET			(1 << 1)
-#define	OMAP_USBTLL_SYSCONFIG_AUTOIDLE			(1 << 0)
-
-#define	OMAP_USBTLL_SYSSTATUS				(0x14)
-#define	OMAP_USBTLL_SYSSTATUS_RESETDONE			(1 << 0)
-
-#define	OMAP_USBTLL_IRQSTATUS				(0x18)
-#define	OMAP_USBTLL_IRQENABLE				(0x1C)
-
-#define	OMAP_TLL_SHARED_CONF				(0x30)
-#define	OMAP_TLL_SHARED_CONF_USB_90D_DDR_EN		(1 << 6)
-#define	OMAP_TLL_SHARED_CONF_USB_180D_SDR_EN		(1 << 5)
-#define	OMAP_TLL_SHARED_CONF_USB_DIVRATION		(1 << 2)
-#define	OMAP_TLL_SHARED_CONF_FCLK_REQ			(1 << 1)
-#define	OMAP_TLL_SHARED_CONF_FCLK_IS_ON			(1 << 0)
-
-#define	OMAP_TLL_CHANNEL_CONF(num)			(0x040 + 0x004 * num)
-#define OMAP_TLL_CHANNEL_CONF_FSLSMODE_SHIFT		24
-#define	OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF		(1 << 11)
-#define	OMAP_TLL_CHANNEL_CONF_ULPI_ULPIAUTOIDLE		(1 << 10)
-#define	OMAP_TLL_CHANNEL_CONF_UTMIAUTOIDLE		(1 << 9)
-#define	OMAP_TLL_CHANNEL_CONF_ULPIDDRMODE		(1 << 8)
-#define OMAP_TLL_CHANNEL_CONF_CHANMODE_FSLS		(1 << 1)
-#define	OMAP_TLL_CHANNEL_CONF_CHANEN			(1 << 0)
-
-#define OMAP_TLL_CHANNEL_COUNT				3
-
-/* UHH Register Set */
-#define	OMAP_UHH_REVISION				(0x00)
-#define	OMAP_UHH_SYSCONFIG				(0x10)
-#define	OMAP_UHH_SYSCONFIG_MIDLEMODE			(1 << 12)
-#define	OMAP_UHH_SYSCONFIG_CACTIVITY			(1 << 8)
-#define	OMAP_UHH_SYSCONFIG_SIDLEMODE			(1 << 3)
-#define	OMAP_UHH_SYSCONFIG_ENAWAKEUP			(1 << 2)
-#define	OMAP_UHH_SYSCONFIG_SOFTRESET			(1 << 1)
-#define	OMAP_UHH_SYSCONFIG_AUTOIDLE			(1 << 0)
-
-#define	OMAP_UHH_SYSSTATUS				(0x14)
-#define OMAP_UHH_SYSSTATUS_UHHRESETDONE			(1 << 0)
-#define OMAP_UHH_SYSSTATUS_OHCIRESETDONE		(1 << 1)
-#define OMAP_UHH_SYSSTATUS_EHCIRESETDONE		(1 << 2)
-#define	OMAP_UHH_HOSTCONFIG				(0x40)
-#define	OMAP_UHH_HOSTCONFIG_ULPI_BYPASS			(1 << 0)
-#define	OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS		(1 << 0)
-#define	OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS		(1 << 11)
-#define	OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS		(1 << 12)
-#define OMAP_UHH_HOSTCONFIG_INCR4_BURST_EN		(1 << 2)
-#define OMAP_UHH_HOSTCONFIG_INCR8_BURST_EN		(1 << 3)
-#define OMAP_UHH_HOSTCONFIG_INCR16_BURST_EN		(1 << 4)
-#define OMAP_UHH_HOSTCONFIG_INCRX_ALIGN_EN		(1 << 5)
-#define OMAP_UHH_HOSTCONFIG_P1_CONNECT_STATUS		(1 << 8)
-#define OMAP_UHH_HOSTCONFIG_P2_CONNECT_STATUS		(1 << 9)
-#define OMAP_UHH_HOSTCONFIG_P3_CONNECT_STATUS		(1 << 10)
-
-#define	OMAP_UHH_DEBUG_CSR				(0x44)
-
 /*-------------------------------------------------------------------------*/
 
-static inline void ohci_omap_writel(void __iomem *base, u32 reg, u32 val)
-{
-	__raw_writel(val, base + reg);
-}
-
-static inline u32 ohci_omap_readl(void __iomem *base, u32 reg)
-{
-	return __raw_readl(base + reg);
-}
-
-static inline void ohci_omap_writeb(void __iomem *base, u8 reg, u8 val)
-{
-	__raw_writeb(val, base + reg);
-}
-
-static inline u8 ohci_omap_readb(void __iomem *base, u8 reg)
-{
-	return __raw_readb(base + reg);
-}
-
-/*-------------------------------------------------------------------------*/
-
-struct ohci_hcd_omap3 {
-	struct ohci_hcd		*ohci;
-	struct device		*dev;
-
-	struct clk		*usbhost_ick;
-	struct clk		*usbhost2_120m_fck;
-	struct clk		*usbhost1_48m_fck;
-	struct clk		*usbtll_fck;
-	struct clk		*usbtll_ick;
-
-	/* port_mode: TLL/PHY, 2/3/4/6-PIN, DP-DM/DAT-SE0 */
-	enum usbhs_omap_port_mode	port_mode[OMAP3_HS_USB_PORTS];
-	void __iomem		*uhh_base;
-	void __iomem		*tll_base;
-	void __iomem		*ohci_base;
-
-	unsigned		es2_compatibility:1;
-};
-
-/*-------------------------------------------------------------------------*/
-
-static void ohci_omap3_clock_power(struct ohci_hcd_omap3 *omap, int on)
-{
-	if (on) {
-		clk_enable(omap->usbtll_ick);
-		clk_enable(omap->usbtll_fck);
-		clk_enable(omap->usbhost_ick);
-		clk_enable(omap->usbhost1_48m_fck);
-		clk_enable(omap->usbhost2_120m_fck);
-	} else {
-		clk_disable(omap->usbhost2_120m_fck);
-		clk_disable(omap->usbhost1_48m_fck);
-		clk_disable(omap->usbhost_ick);
-		clk_disable(omap->usbtll_fck);
-		clk_disable(omap->usbtll_ick);
-	}
-}
-
 static int ohci_omap3_init(struct usb_hcd *hcd)
 {
 	dev_dbg(hcd->self.controller, "starting OHCI controller\n");
@@ -175,7 +41,6 @@
 	return ohci_init(hcd_to_ohci(hcd));
 }
 
-
 /*-------------------------------------------------------------------------*/
 
 static int ohci_omap3_start(struct usb_hcd *hcd)
@@ -202,325 +67,6 @@
 
 /*-------------------------------------------------------------------------*/
 
-/*
- * convert the port-mode enum to a value we can use in the FSLSMODE
- * field of USBTLL_CHANNEL_CONF
- */
-static unsigned ohci_omap3_fslsmode(enum usbhs_omap_port_mode mode)
-{
-	switch (mode) {
-	case OMAP_USBHS_PORT_MODE_UNUSED:
-	case OMAP_OHCI_PORT_MODE_PHY_6PIN_DATSE0:
-		return 0x0;
-
-	case OMAP_OHCI_PORT_MODE_PHY_6PIN_DPDM:
-		return 0x1;
-
-	case OMAP_OHCI_PORT_MODE_PHY_3PIN_DATSE0:
-		return 0x2;
-
-	case OMAP_OHCI_PORT_MODE_PHY_4PIN_DPDM:
-		return 0x3;
-
-	case OMAP_OHCI_PORT_MODE_TLL_6PIN_DATSE0:
-		return 0x4;
-
-	case OMAP_OHCI_PORT_MODE_TLL_6PIN_DPDM:
-		return 0x5;
-
-	case OMAP_OHCI_PORT_MODE_TLL_3PIN_DATSE0:
-		return 0x6;
-
-	case OMAP_OHCI_PORT_MODE_TLL_4PIN_DPDM:
-		return 0x7;
-
-	case OMAP_OHCI_PORT_MODE_TLL_2PIN_DATSE0:
-		return 0xA;
-
-	case OMAP_OHCI_PORT_MODE_TLL_2PIN_DPDM:
-		return 0xB;
-	default:
-		pr_warning("Invalid port mode, using default\n");
-		return 0x0;
-	}
-}
-
-static void ohci_omap3_tll_config(struct ohci_hcd_omap3 *omap)
-{
-	u32 reg;
-	int i;
-
-	/* Program TLL SHARED CONF */
-	reg = ohci_omap_readl(omap->tll_base, OMAP_TLL_SHARED_CONF);
-	reg &= ~OMAP_TLL_SHARED_CONF_USB_90D_DDR_EN;
-	reg &= ~OMAP_TLL_SHARED_CONF_USB_180D_SDR_EN;
-	reg |= OMAP_TLL_SHARED_CONF_USB_DIVRATION;
-	reg |= OMAP_TLL_SHARED_CONF_FCLK_IS_ON;
-	ohci_omap_writel(omap->tll_base, OMAP_TLL_SHARED_CONF, reg);
-
-	/* Program each TLL channel */
-	/*
-	 * REVISIT: Only the 3-pin and 4-pin PHY modes have
-	 * actually been tested.
-	 */
-	for (i = 0; i < OMAP_TLL_CHANNEL_COUNT; i++) {
-
-		/* Enable only those channels that are actually used */
-		if (omap->port_mode[i] == OMAP_USBHS_PORT_MODE_UNUSED)
-			continue;
-
-		reg = ohci_omap_readl(omap->tll_base, OMAP_TLL_CHANNEL_CONF(i));
-		reg |= ohci_omap3_fslsmode(omap->port_mode[i])
-				<< OMAP_TLL_CHANNEL_CONF_FSLSMODE_SHIFT;
-		reg |= OMAP_TLL_CHANNEL_CONF_CHANMODE_FSLS;
-		reg |= OMAP_TLL_CHANNEL_CONF_CHANEN;
-		ohci_omap_writel(omap->tll_base, OMAP_TLL_CHANNEL_CONF(i), reg);
-	}
-}
-
-/* omap3_start_ohci
- *	- Start the TI USBHOST controller
- */
-static int omap3_start_ohci(struct ohci_hcd_omap3 *omap, struct usb_hcd *hcd)
-{
-	unsigned long timeout = jiffies + msecs_to_jiffies(1000);
-	u32 reg = 0;
-	int ret = 0;
-
-	dev_dbg(omap->dev, "starting TI OHCI USB Controller\n");
-
-	/* Get all the clock handles we need */
-	omap->usbhost_ick = clk_get(omap->dev, "usbhost_ick");
-	if (IS_ERR(omap->usbhost_ick)) {
-		dev_err(omap->dev, "could not get usbhost_ick\n");
-		ret =  PTR_ERR(omap->usbhost_ick);
-		goto err_host_ick;
-	}
-
-	omap->usbhost2_120m_fck = clk_get(omap->dev, "usbhost_120m_fck");
-	if (IS_ERR(omap->usbhost2_120m_fck)) {
-		dev_err(omap->dev, "could not get usbhost_120m_fck\n");
-		ret = PTR_ERR(omap->usbhost2_120m_fck);
-		goto err_host_120m_fck;
-	}
-
-	omap->usbhost1_48m_fck = clk_get(omap->dev, "usbhost_48m_fck");
-	if (IS_ERR(omap->usbhost1_48m_fck)) {
-		dev_err(omap->dev, "could not get usbhost_48m_fck\n");
-		ret = PTR_ERR(omap->usbhost1_48m_fck);
-		goto err_host_48m_fck;
-	}
-
-	omap->usbtll_fck = clk_get(omap->dev, "usbtll_fck");
-	if (IS_ERR(omap->usbtll_fck)) {
-		dev_err(omap->dev, "could not get usbtll_fck\n");
-		ret = PTR_ERR(omap->usbtll_fck);
-		goto err_tll_fck;
-	}
-
-	omap->usbtll_ick = clk_get(omap->dev, "usbtll_ick");
-	if (IS_ERR(omap->usbtll_ick)) {
-		dev_err(omap->dev, "could not get usbtll_ick\n");
-		ret = PTR_ERR(omap->usbtll_ick);
-		goto err_tll_ick;
-	}
-
-	/* Now enable all the clocks in the correct order */
-	ohci_omap3_clock_power(omap, 1);
-
-	/* perform TLL soft reset, and wait until reset is complete */
-	ohci_omap_writel(omap->tll_base, OMAP_USBTLL_SYSCONFIG,
-			OMAP_USBTLL_SYSCONFIG_SOFTRESET);
-
-	/* Wait for TLL reset to complete */
-	while (!(ohci_omap_readl(omap->tll_base, OMAP_USBTLL_SYSSTATUS)
-			& OMAP_USBTLL_SYSSTATUS_RESETDONE)) {
-		cpu_relax();
-
-		if (time_after(jiffies, timeout)) {
-			dev_dbg(omap->dev, "operation timed out\n");
-			ret = -EINVAL;
-			goto err_sys_status;
-		}
-	}
-
-	dev_dbg(omap->dev, "TLL reset done\n");
-
-	/* (1<<3) = no idle mode only for initial debugging */
-	ohci_omap_writel(omap->tll_base, OMAP_USBTLL_SYSCONFIG,
-			OMAP_USBTLL_SYSCONFIG_ENAWAKEUP |
-			OMAP_USBTLL_SYSCONFIG_SIDLEMODE |
-			OMAP_USBTLL_SYSCONFIG_CACTIVITY);
-
-
-	/* Put UHH in NoIdle/NoStandby mode */
-	reg = ohci_omap_readl(omap->uhh_base, OMAP_UHH_SYSCONFIG);
-	reg |= (OMAP_UHH_SYSCONFIG_ENAWAKEUP
-			| OMAP_UHH_SYSCONFIG_SIDLEMODE
-			| OMAP_UHH_SYSCONFIG_CACTIVITY
-			| OMAP_UHH_SYSCONFIG_MIDLEMODE);
-	reg &= ~OMAP_UHH_SYSCONFIG_AUTOIDLE;
-	reg &= ~OMAP_UHH_SYSCONFIG_SOFTRESET;
-
-	ohci_omap_writel(omap->uhh_base, OMAP_UHH_SYSCONFIG, reg);
-
-	reg = ohci_omap_readl(omap->uhh_base, OMAP_UHH_HOSTCONFIG);
-
-	/* setup ULPI bypass and burst configurations */
-	reg |= (OMAP_UHH_HOSTCONFIG_INCR4_BURST_EN
-			| OMAP_UHH_HOSTCONFIG_INCR8_BURST_EN
-			| OMAP_UHH_HOSTCONFIG_INCR16_BURST_EN);
-	reg &= ~OMAP_UHH_HOSTCONFIG_INCRX_ALIGN_EN;
-
-	/*
-	 * REVISIT: Pi_CONNECT_STATUS controls MStandby
-	 * assertion and Swakeup generation - let us not
-	 * worry about this for now. OMAP HWMOD framework
-	 * might take care of this later. If not, we can
-	 * update these registers when adding aggressive
-	 * clock management code.
-	 *
-	 * For now, turn off all the Pi_CONNECT_STATUS bits
-	 *
-	if (omap->port_mode[0] == OMAP_USBHS_PORT_MODE_UNUSED)
-		reg &= ~OMAP_UHH_HOSTCONFIG_P1_CONNECT_STATUS;
-	if (omap->port_mode[1] == OMAP_USBHS_PORT_MODE_UNUSED)
-		reg &= ~OMAP_UHH_HOSTCONFIG_P2_CONNECT_STATUS;
-	if (omap->port_mode[2] == OMAP_USBHS_PORT_MODE_UNUSED)
-		reg &= ~OMAP_UHH_HOSTCONFIG_P3_CONNECT_STATUS;
-	 */
-	reg &= ~OMAP_UHH_HOSTCONFIG_P1_CONNECT_STATUS;
-	reg &= ~OMAP_UHH_HOSTCONFIG_P2_CONNECT_STATUS;
-	reg &= ~OMAP_UHH_HOSTCONFIG_P3_CONNECT_STATUS;
-
-	 if (omap->es2_compatibility) {
-		/*
-		 * All OHCI modes need to go through the TLL,
-		 * unlike in the EHCI case. So use UTMI mode
-		 * for all ports for OHCI, on ES2.x silicon
-		 */
-		dev_dbg(omap->dev, "OMAP3 ES version <= ES2.1\n");
-		reg |= OMAP_UHH_HOSTCONFIG_ULPI_BYPASS;
-	} else {
-		dev_dbg(omap->dev, "OMAP3 ES version > ES2.1\n");
-		if (omap->port_mode[0] == OMAP_USBHS_PORT_MODE_UNUSED)
-			reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS;
-		else
-			reg |= OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS;
-
-		if (omap->port_mode[1] == OMAP_USBHS_PORT_MODE_UNUSED)
-			reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS;
-		else
-			reg |= OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS;
-
-		if (omap->port_mode[2] == OMAP_USBHS_PORT_MODE_UNUSED)
-			reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS;
-		else
-			reg |= OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS;
-
-	}
-	ohci_omap_writel(omap->uhh_base, OMAP_UHH_HOSTCONFIG, reg);
-	dev_dbg(omap->dev, "UHH setup done, uhh_hostconfig=%x\n", reg);
-
-	ohci_omap3_tll_config(omap);
-
-	return 0;
-
-err_sys_status:
-	ohci_omap3_clock_power(omap, 0);
-	clk_put(omap->usbtll_ick);
-
-err_tll_ick:
-	clk_put(omap->usbtll_fck);
-
-err_tll_fck:
-	clk_put(omap->usbhost1_48m_fck);
-
-err_host_48m_fck:
-	clk_put(omap->usbhost2_120m_fck);
-
-err_host_120m_fck:
-	clk_put(omap->usbhost_ick);
-
-err_host_ick:
-	return ret;
-}
-
-static void omap3_stop_ohci(struct ohci_hcd_omap3 *omap, struct usb_hcd *hcd)
-{
-	unsigned long timeout = jiffies + msecs_to_jiffies(100);
-
-	dev_dbg(omap->dev, "stopping TI EHCI USB Controller\n");
-
-	/* Reset USBHOST for insmod/rmmod to work */
-	ohci_omap_writel(omap->uhh_base, OMAP_UHH_SYSCONFIG,
-			OMAP_UHH_SYSCONFIG_SOFTRESET);
-	while (!(ohci_omap_readl(omap->uhh_base, OMAP_UHH_SYSSTATUS)
-				& OMAP_UHH_SYSSTATUS_UHHRESETDONE)) {
-		cpu_relax();
-
-		if (time_after(jiffies, timeout))
-			dev_dbg(omap->dev, "operation timed out\n");
-	}
-
-	while (!(ohci_omap_readl(omap->uhh_base, OMAP_UHH_SYSSTATUS)
-				& OMAP_UHH_SYSSTATUS_OHCIRESETDONE)) {
-		cpu_relax();
-
-		if (time_after(jiffies, timeout))
-			dev_dbg(omap->dev, "operation timed out\n");
-	}
-
-	while (!(ohci_omap_readl(omap->uhh_base, OMAP_UHH_SYSSTATUS)
-				& OMAP_UHH_SYSSTATUS_EHCIRESETDONE)) {
-		cpu_relax();
-
-		if (time_after(jiffies, timeout))
-			dev_dbg(omap->dev, "operation timed out\n");
-	}
-
-	ohci_omap_writel(omap->tll_base, OMAP_USBTLL_SYSCONFIG, (1 << 1));
-
-	while (!(ohci_omap_readl(omap->tll_base, OMAP_USBTLL_SYSSTATUS)
-				& (1 << 0))) {
-		cpu_relax();
-
-		if (time_after(jiffies, timeout))
-			dev_dbg(omap->dev, "operation timed out\n");
-	}
-
-	ohci_omap3_clock_power(omap, 0);
-
-	if (omap->usbtll_fck != NULL) {
-		clk_put(omap->usbtll_fck);
-		omap->usbtll_fck = NULL;
-	}
-
-	if (omap->usbhost_ick != NULL) {
-		clk_put(omap->usbhost_ick);
-		omap->usbhost_ick = NULL;
-	}
-
-	if (omap->usbhost1_48m_fck != NULL) {
-		clk_put(omap->usbhost1_48m_fck);
-		omap->usbhost1_48m_fck = NULL;
-	}
-
-	if (omap->usbhost2_120m_fck != NULL) {
-		clk_put(omap->usbhost2_120m_fck);
-		omap->usbhost2_120m_fck = NULL;
-	}
-
-	if (omap->usbtll_ick != NULL) {
-		clk_put(omap->usbtll_ick);
-		omap->usbtll_ick = NULL;
-	}
-
-	dev_dbg(omap->dev, "Clock to USB host has been disabled\n");
-}
-
-/*-------------------------------------------------------------------------*/
-
 static const struct hc_driver ohci_omap3_hc_driver = {
 	.description =		hcd_name,
 	.product_desc =		"OMAP3 OHCI Host Controller",
@@ -580,107 +126,77 @@
  */
 static int __devinit ohci_hcd_omap3_probe(struct platform_device *pdev)
 {
-	struct usbhs_omap_board_data *pdata = pdev->dev.platform_data;
-	struct ohci_hcd_omap3 *omap;
-	struct resource *res;
-	struct usb_hcd *hcd;
-	int ret = -ENODEV;
-	int irq;
+	struct device		*dev = &pdev->dev;
+	struct usb_hcd		*hcd = NULL;
+	void __iomem		*regs = NULL;
+	struct resource		*res;
+	int			ret = -ENODEV;
+	int			irq;
 
 	if (usb_disabled())
-		goto err_disabled;
+		goto err_end;
 
-	if (!pdata) {
-		dev_dbg(&pdev->dev, "missing platform_data\n");
-		goto err_pdata;
+	if (!dev->parent) {
+		dev_err(dev, "Missing parent device\n");
+		return -ENODEV;
 	}
 
-	irq = platform_get_irq(pdev, 0);
-
-	omap = kzalloc(sizeof(*omap), GFP_KERNEL);
-	if (!omap) {
-		ret = -ENOMEM;
-		goto err_disabled;
+	irq = platform_get_irq_byname(pdev, "ohci-irq");
+	if (irq < 0) {
+		dev_err(dev, "OHCI irq failed\n");
+		return -ENODEV;
 	}
 
-	hcd = usb_create_hcd(&ohci_omap3_hc_driver, &pdev->dev,
-			dev_name(&pdev->dev));
+	res = platform_get_resource_byname(pdev,
+				IORESOURCE_MEM, "ohci");
+	if (!ret) {
+		dev_err(dev, "UHH OHCI get resource failed\n");
+		return -ENOMEM;
+	}
+
+	regs = ioremap(res->start, resource_size(res));
+	if (!regs) {
+		dev_err(dev, "UHH OHCI ioremap failed\n");
+		return -ENOMEM;
+	}
+
+
+	hcd = usb_create_hcd(&ohci_omap3_hc_driver, dev,
+			dev_name(dev));
 	if (!hcd) {
-		ret = -ENOMEM;
-		goto err_create_hcd;
+		dev_err(dev, "usb_create_hcd failed\n");
+		goto err_io;
 	}
 
-	platform_set_drvdata(pdev, omap);
-	omap->dev		= &pdev->dev;
-	omap->port_mode[0]	= pdata->port_mode[0];
-	omap->port_mode[1]	= pdata->port_mode[1];
-	omap->port_mode[2]	= pdata->port_mode[2];
-	omap->es2_compatibility	= pdata->es2_compatibility;
-	omap->ohci		= hcd_to_ohci(hcd);
-
-	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ohci");
-
 	hcd->rsrc_start = res->start;
 	hcd->rsrc_len = resource_size(res);
+	hcd->regs =  regs;
 
-	hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
-	if (!hcd->regs) {
-		dev_err(&pdev->dev, "OHCI ioremap failed\n");
-		ret = -ENOMEM;
-		goto err_ioremap;
-	}
-
-	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "uhh");
-	omap->uhh_base = ioremap(res->start, resource_size(res));
-	if (!omap->uhh_base) {
-		dev_err(&pdev->dev, "UHH ioremap failed\n");
-		ret = -ENOMEM;
-		goto err_uhh_ioremap;
-	}
-
-	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "tll");
-	omap->tll_base = ioremap(res->start, resource_size(res));
-	if (!omap->tll_base) {
-		dev_err(&pdev->dev, "TLL ioremap failed\n");
-		ret = -ENOMEM;
-		goto err_tll_ioremap;
-	}
-
-	ret = omap3_start_ohci(omap, hcd);
+	ret = omap_usbhs_enable(dev);
 	if (ret) {
-		dev_dbg(&pdev->dev, "failed to start ohci\n");
-		goto err_start;
+		dev_dbg(dev, "failed to start ohci\n");
+		goto err_end;
 	}
 
-	ohci_hcd_init(omap->ohci);
+	ohci_hcd_init(hcd_to_ohci(hcd));
 
 	ret = usb_add_hcd(hcd, irq, IRQF_DISABLED);
 	if (ret) {
-		dev_dbg(&pdev->dev, "failed to add hcd with err %d\n", ret);
+		dev_dbg(dev, "failed to add hcd with err %d\n", ret);
 		goto err_add_hcd;
 	}
 
 	return 0;
 
 err_add_hcd:
-	omap3_stop_ohci(omap, hcd);
+	omap_usbhs_disable(dev);
 
-err_start:
-	iounmap(omap->tll_base);
-
-err_tll_ioremap:
-	iounmap(omap->uhh_base);
-
-err_uhh_ioremap:
-	iounmap(hcd->regs);
-
-err_ioremap:
+err_end:
 	usb_put_hcd(hcd);
 
-err_create_hcd:
-	kfree(omap);
-err_pdata:
-err_disabled:
+err_io:
+	iounmap(regs);
+
 	return ret;
 }
 
@@ -699,24 +215,20 @@
  */
 static int __devexit ohci_hcd_omap3_remove(struct platform_device *pdev)
 {
-	struct ohci_hcd_omap3 *omap = platform_get_drvdata(pdev);
-	struct usb_hcd *hcd = ohci_to_hcd(omap->ohci);
+	struct device *dev	= &pdev->dev;
+	struct usb_hcd *hcd	= dev_get_drvdata(dev);
 
-	usb_remove_hcd(hcd);
-	omap3_stop_ohci(omap, hcd);
 	iounmap(hcd->regs);
-	iounmap(omap->tll_base);
-	iounmap(omap->uhh_base);
+	usb_remove_hcd(hcd);
+	omap_usbhs_disable(dev);
 	usb_put_hcd(hcd);
-	kfree(omap);
 
 	return 0;
 }
 
 static void ohci_hcd_omap3_shutdown(struct platform_device *pdev)
 {
-	struct ohci_hcd_omap3 *omap = platform_get_drvdata(pdev);
-	struct usb_hcd *hcd = ohci_to_hcd(omap->ohci);
+	struct usb_hcd *hcd = dev_get_drvdata(&pdev->dev);
 
 	if (hcd->driver->shutdown)
 		hcd->driver->shutdown(hcd);