Merge branch 'next' into for-linus-3.0
diff --git a/Documentation/dmaengine.txt b/Documentation/dmaengine.txt
index 5a0cb1e..94b7e0f 100644
--- a/Documentation/dmaengine.txt
+++ b/Documentation/dmaengine.txt
@@ -10,87 +10,181 @@
Below is a guide to device driver writers on how to use the Slave-DMA API of the
DMA Engine. This is applicable only for slave DMA usage only.
-The slave DMA usage consists of following steps
+The slave DMA usage consists of following steps:
1. Allocate a DMA slave channel
2. Set slave and controller specific parameters
3. Get a descriptor for transaction
-4. Submit the transaction and wait for callback notification
+4. Submit the transaction
+5. Issue pending requests and wait for callback notification
1. Allocate a DMA slave channel
-Channel allocation is slightly different in the slave DMA context, client
-drivers typically need a channel from a particular DMA controller only and even
-in some cases a specific channel is desired. To request a channel
-dma_request_channel() API is used.
-Interface:
-struct dma_chan *dma_request_channel(dma_cap_mask_t mask,
- dma_filter_fn filter_fn,
- void *filter_param);
-where dma_filter_fn is defined as:
-typedef bool (*dma_filter_fn)(struct dma_chan *chan, void *filter_param);
+ Channel allocation is slightly different in the slave DMA context,
+ client drivers typically need a channel from a particular DMA
+ controller only and even in some cases a specific channel is desired.
+ To request a channel dma_request_channel() API is used.
-When the optional 'filter_fn' parameter is set to NULL dma_request_channel
-simply returns the first channel that satisfies the capability mask. Otherwise,
-when the mask parameter is insufficient for specifying the necessary channel,
-the filter_fn routine can be used to disposition the available channels in the
-system. The filter_fn routine is called once for each free channel in the
-system. Upon seeing a suitable channel filter_fn returns DMA_ACK which flags
-that channel to be the return value from dma_request_channel. A channel
-allocated via this interface is exclusive to the caller, until
-dma_release_channel() is called.
+ Interface:
+ struct dma_chan *dma_request_channel(dma_cap_mask_t mask,
+ dma_filter_fn filter_fn,
+ void *filter_param);
+ where dma_filter_fn is defined as:
+ typedef bool (*dma_filter_fn)(struct dma_chan *chan, void *filter_param);
+
+ The 'filter_fn' parameter is optional, but highly recommended for
+ slave and cyclic channels as they typically need to obtain a specific
+ DMA channel.
+
+ When the optional 'filter_fn' parameter is NULL, dma_request_channel()
+ simply returns the first channel that satisfies the capability mask.
+
+ Otherwise, the 'filter_fn' routine will be called once for each free
+ channel which has a capability in 'mask'. 'filter_fn' is expected to
+ return 'true' when the desired DMA channel is found.
+
+ A channel allocated via this interface is exclusive to the caller,
+ until dma_release_channel() is called.
2. Set slave and controller specific parameters
-Next step is always to pass some specific information to the DMA driver. Most of
-the generic information which a slave DMA can use is in struct dma_slave_config.
-It allows the clients to specify DMA direction, DMA addresses, bus widths, DMA
-burst lengths etc. If some DMA controllers have more parameters to be sent then
-they should try to embed struct dma_slave_config in their controller specific
-structure. That gives flexibility to client to pass more parameters, if
-required.
-Interface:
-int dmaengine_slave_config(struct dma_chan *chan,
- struct dma_slave_config *config)
+ Next step is always to pass some specific information to the DMA
+ driver. Most of the generic information which a slave DMA can use
+ is in struct dma_slave_config. This allows the clients to specify
+ DMA direction, DMA addresses, bus widths, DMA burst lengths etc
+ for the peripheral.
+
+ If some DMA controllers have more parameters to be sent then they
+ should try to embed struct dma_slave_config in their controller
+ specific structure. That gives flexibility to client to pass more
+ parameters, if required.
+
+ Interface:
+ int dmaengine_slave_config(struct dma_chan *chan,
+ struct dma_slave_config *config)
+
+ Please see the dma_slave_config structure definition in dmaengine.h
+ for a detailed explaination of the struct members. Please note
+ that the 'direction' member will be going away as it duplicates the
+ direction given in the prepare call.
3. Get a descriptor for transaction
-For slave usage the various modes of slave transfers supported by the
-DMA-engine are:
-slave_sg - DMA a list of scatter gather buffers from/to a peripheral
-dma_cyclic - Perform a cyclic DMA operation from/to a peripheral till the
+
+ For slave usage the various modes of slave transfers supported by the
+ DMA-engine are:
+
+ slave_sg - DMA a list of scatter gather buffers from/to a peripheral
+ dma_cyclic - Perform a cyclic DMA operation from/to a peripheral till the
operation is explicitly stopped.
-The non NULL return of this transfer API represents a "descriptor" for the given
-transaction.
-Interface:
-struct dma_async_tx_descriptor *(*chan->device->device_prep_dma_sg)(
- struct dma_chan *chan,
- struct scatterlist *dst_sg, unsigned int dst_nents,
- struct scatterlist *src_sg, unsigned int src_nents,
+ A non-NULL return of this transfer API represents a "descriptor" for
+ the given transaction.
+
+ Interface:
+ struct dma_async_tx_descriptor *(*chan->device->device_prep_slave_sg)(
+ struct dma_chan *chan, struct scatterlist *sgl,
+ unsigned int sg_len, enum dma_data_direction direction,
unsigned long flags);
-struct dma_async_tx_descriptor *(*chan->device->device_prep_dma_cyclic)(
+
+ struct dma_async_tx_descriptor *(*chan->device->device_prep_dma_cyclic)(
struct dma_chan *chan, dma_addr_t buf_addr, size_t buf_len,
size_t period_len, enum dma_data_direction direction);
-4. Submit the transaction and wait for callback notification
-To schedule the transaction to be scheduled by dma device, the "descriptor"
-returned in above (3) needs to be submitted.
-To tell the dma driver that a transaction is ready to be serviced, the
-descriptor->submit() callback needs to be invoked. This chains the descriptor to
-the pending queue.
-The transactions in the pending queue can be activated by calling the
-issue_pending API. If channel is idle then the first transaction in queue is
-started and subsequent ones queued up.
-On completion of the DMA operation the next in queue is submitted and a tasklet
-triggered. The tasklet would then call the client driver completion callback
-routine for notification, if set.
-Interface:
-void dma_async_issue_pending(struct dma_chan *chan);
+ The peripheral driver is expected to have mapped the scatterlist for
+ the DMA operation prior to calling device_prep_slave_sg, and must
+ keep the scatterlist mapped until the DMA operation has completed.
+ The scatterlist must be mapped using the DMA struct device. So,
+ normal setup should look like this:
-==============================================================================
+ nr_sg = dma_map_sg(chan->device->dev, sgl, sg_len);
+ if (nr_sg == 0)
+ /* error */
-Additional usage notes for dma driver writers
-1/ Although DMA engine specifies that completion callback routines cannot submit
-any new operations, but typically for slave DMA subsequent transaction may not
-be available for submit prior to callback routine being called. This requirement
-is not a requirement for DMA-slave devices. But they should take care to drop
-the spin-lock they might be holding before calling the callback routine
+ desc = chan->device->device_prep_slave_sg(chan, sgl, nr_sg,
+ direction, flags);
+
+ Once a descriptor has been obtained, the callback information can be
+ added and the descriptor must then be submitted. Some DMA engine
+ drivers may hold a spinlock between a successful preparation and
+ submission so it is important that these two operations are closely
+ paired.
+
+ Note:
+ Although the async_tx API specifies that completion callback
+ routines cannot submit any new operations, this is not the
+ case for slave/cyclic DMA.
+
+ For slave DMA, the subsequent transaction may not be available
+ for submission prior to callback function being invoked, so
+ slave DMA callbacks are permitted to prepare and submit a new
+ transaction.
+
+ For cyclic DMA, a callback function may wish to terminate the
+ DMA via dmaengine_terminate_all().
+
+ Therefore, it is important that DMA engine drivers drop any
+ locks before calling the callback function which may cause a
+ deadlock.
+
+ Note that callbacks will always be invoked from the DMA
+ engines tasklet, never from interrupt context.
+
+4. Submit the transaction
+
+ Once the descriptor has been prepared and the callback information
+ added, it must be placed on the DMA engine drivers pending queue.
+
+ Interface:
+ dma_cookie_t dmaengine_submit(struct dma_async_tx_descriptor *desc)
+
+ This returns a cookie can be used to check the progress of DMA engine
+ activity via other DMA engine calls not covered in this document.
+
+ dmaengine_submit() will not start the DMA operation, it merely adds
+ it to the pending queue. For this, see step 5, dma_async_issue_pending.
+
+5. Issue pending DMA requests and wait for callback notification
+
+ The transactions in the pending queue can be activated by calling the
+ issue_pending API. If channel is idle then the first transaction in
+ queue is started and subsequent ones queued up.
+
+ On completion of each DMA operation, the next in queue is started and
+ a tasklet triggered. The tasklet will then call the client driver
+ completion callback routine for notification, if set.
+
+ Interface:
+ void dma_async_issue_pending(struct dma_chan *chan);
+
+Further APIs:
+
+1. int dmaengine_terminate_all(struct dma_chan *chan)
+
+ This causes all activity for the DMA channel to be stopped, and may
+ discard data in the DMA FIFO which hasn't been fully transferred.
+ No callback functions will be called for any incomplete transfers.
+
+2. int dmaengine_pause(struct dma_chan *chan)
+
+ This pauses activity on the DMA channel without data loss.
+
+3. int dmaengine_resume(struct dma_chan *chan)
+
+ Resume a previously paused DMA channel. It is invalid to resume a
+ channel which is not currently paused.
+
+4. enum dma_status dma_async_is_tx_complete(struct dma_chan *chan,
+ dma_cookie_t cookie, dma_cookie_t *last, dma_cookie_t *used)
+
+ This can be used to check the status of the channel. Please see
+ the documentation in include/linux/dmaengine.h for a more complete
+ description of this API.
+
+ This can be used in conjunction with dma_async_is_complete() and
+ the cookie returned from 'descriptor->submit()' to check for
+ completion of a specific DMA transaction.
+
+ Note:
+ Not all DMA engine drivers can return reliable information for
+ a running DMA channel. It is recommended that DMA engine users
+ pause or stop (via dmaengine_terminate_all) the channel before
+ using this API.
diff --git a/Documentation/spi/ep93xx_spi b/Documentation/spi/ep93xx_spi
index 6325f5b..d8eb01c 100644
--- a/Documentation/spi/ep93xx_spi
+++ b/Documentation/spi/ep93xx_spi
@@ -88,6 +88,16 @@
ARRAY_SIZE(ts72xx_spi_devices));
}
+The driver can use DMA for the transfers also. In this case ts72xx_spi_info
+becomes:
+
+static struct ep93xx_spi_info ts72xx_spi_info = {
+ .num_chipselect = ARRAY_SIZE(ts72xx_spi_devices),
+ .use_dma = true;
+};
+
+Note that CONFIG_EP93XX_DMA should be enabled as well.
+
Thanks to
=========
Martin Guy, H. Hartley Sweeten and others who helped me during development of
diff --git a/arch/arm/mach-ep93xx/Makefile b/arch/arm/mach-ep93xx/Makefile
index 33ee2c8..21e721a 100644
--- a/arch/arm/mach-ep93xx/Makefile
+++ b/arch/arm/mach-ep93xx/Makefile
@@ -1,11 +1,13 @@
#
# Makefile for the linux kernel.
#
-obj-y := core.o clock.o dma-m2p.o gpio.o
+obj-y := core.o clock.o gpio.o
obj-m :=
obj-n :=
obj- :=
+obj-$(CONFIG_EP93XX_DMA) += dma.o
+
obj-$(CONFIG_MACH_ADSSPHERE) += adssphere.o
obj-$(CONFIG_MACH_EDB93XX) += edb93xx.o
obj-$(CONFIG_MACH_GESBC9312) += gesbc9312.o
diff --git a/arch/arm/mach-ep93xx/core.c b/arch/arm/mach-ep93xx/core.c
index 6659a0d..dd87a82 100644
--- a/arch/arm/mach-ep93xx/core.c
+++ b/arch/arm/mach-ep93xx/core.c
@@ -492,11 +492,15 @@
},
};
+static u64 ep93xx_spi_dma_mask = DMA_BIT_MASK(32);
+
static struct platform_device ep93xx_spi_device = {
.name = "ep93xx-spi",
.id = 0,
.dev = {
- .platform_data = &ep93xx_spi_master_data,
+ .platform_data = &ep93xx_spi_master_data,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .dma_mask = &ep93xx_spi_dma_mask,
},
.num_resources = ARRAY_SIZE(ep93xx_spi_resources),
.resource = ep93xx_spi_resources,
diff --git a/arch/arm/mach-ep93xx/dma-m2p.c b/arch/arm/mach-ep93xx/dma-m2p.c
deleted file mode 100644
index a696d35..0000000
--- a/arch/arm/mach-ep93xx/dma-m2p.c
+++ /dev/null
@@ -1,411 +0,0 @@
-/*
- * arch/arm/mach-ep93xx/dma-m2p.c
- * M2P DMA handling for Cirrus EP93xx chips.
- *
- * Copyright (C) 2006 Lennert Buytenhek <buytenh@wantstofly.org>
- * Copyright (C) 2006 Applied Data Systems
- *
- * Copyright (C) 2009 Ryan Mallon <ryan@bluewatersys.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or (at
- * your option) any later version.
- */
-
-/*
- * On the EP93xx chip the following peripherals my be allocated to the 10
- * Memory to Internal Peripheral (M2P) channels (5 transmit + 5 receive).
- *
- * I2S contains 3 Tx and 3 Rx DMA Channels
- * AAC contains 3 Tx and 3 Rx DMA Channels
- * UART1 contains 1 Tx and 1 Rx DMA Channels
- * UART2 contains 1 Tx and 1 Rx DMA Channels
- * UART3 contains 1 Tx and 1 Rx DMA Channels
- * IrDA contains 1 Tx and 1 Rx DMA Channels
- *
- * SSP and IDE use the Memory to Memory (M2M) channels and are not covered
- * with this implementation.
- */
-
-#define pr_fmt(fmt) "ep93xx " KBUILD_MODNAME ": " fmt
-
-#include <linux/kernel.h>
-#include <linux/clk.h>
-#include <linux/err.h>
-#include <linux/interrupt.h>
-#include <linux/module.h>
-#include <linux/io.h>
-
-#include <mach/dma.h>
-#include <mach/hardware.h>
-
-#define M2P_CONTROL 0x00
-#define M2P_CONTROL_STALL_IRQ_EN (1 << 0)
-#define M2P_CONTROL_NFB_IRQ_EN (1 << 1)
-#define M2P_CONTROL_ERROR_IRQ_EN (1 << 3)
-#define M2P_CONTROL_ENABLE (1 << 4)
-#define M2P_INTERRUPT 0x04
-#define M2P_INTERRUPT_STALL (1 << 0)
-#define M2P_INTERRUPT_NFB (1 << 1)
-#define M2P_INTERRUPT_ERROR (1 << 3)
-#define M2P_PPALLOC 0x08
-#define M2P_STATUS 0x0c
-#define M2P_REMAIN 0x14
-#define M2P_MAXCNT0 0x20
-#define M2P_BASE0 0x24
-#define M2P_MAXCNT1 0x30
-#define M2P_BASE1 0x34
-
-#define STATE_IDLE 0 /* Channel is inactive. */
-#define STATE_STALL 1 /* Channel is active, no buffers pending. */
-#define STATE_ON 2 /* Channel is active, one buffer pending. */
-#define STATE_NEXT 3 /* Channel is active, two buffers pending. */
-
-struct m2p_channel {
- char *name;
- void __iomem *base;
- int irq;
-
- struct clk *clk;
- spinlock_t lock;
-
- void *client;
- unsigned next_slot:1;
- struct ep93xx_dma_buffer *buffer_xfer;
- struct ep93xx_dma_buffer *buffer_next;
- struct list_head buffers_pending;
-};
-
-static struct m2p_channel m2p_rx[] = {
- {"m2p1", EP93XX_DMA_BASE + 0x0040, IRQ_EP93XX_DMAM2P1},
- {"m2p3", EP93XX_DMA_BASE + 0x00c0, IRQ_EP93XX_DMAM2P3},
- {"m2p5", EP93XX_DMA_BASE + 0x0200, IRQ_EP93XX_DMAM2P5},
- {"m2p7", EP93XX_DMA_BASE + 0x0280, IRQ_EP93XX_DMAM2P7},
- {"m2p9", EP93XX_DMA_BASE + 0x0300, IRQ_EP93XX_DMAM2P9},
- {NULL},
-};
-
-static struct m2p_channel m2p_tx[] = {
- {"m2p0", EP93XX_DMA_BASE + 0x0000, IRQ_EP93XX_DMAM2P0},
- {"m2p2", EP93XX_DMA_BASE + 0x0080, IRQ_EP93XX_DMAM2P2},
- {"m2p4", EP93XX_DMA_BASE + 0x0240, IRQ_EP93XX_DMAM2P4},
- {"m2p6", EP93XX_DMA_BASE + 0x02c0, IRQ_EP93XX_DMAM2P6},
- {"m2p8", EP93XX_DMA_BASE + 0x0340, IRQ_EP93XX_DMAM2P8},
- {NULL},
-};
-
-static void feed_buf(struct m2p_channel *ch, struct ep93xx_dma_buffer *buf)
-{
- if (ch->next_slot == 0) {
- writel(buf->size, ch->base + M2P_MAXCNT0);
- writel(buf->bus_addr, ch->base + M2P_BASE0);
- } else {
- writel(buf->size, ch->base + M2P_MAXCNT1);
- writel(buf->bus_addr, ch->base + M2P_BASE1);
- }
- ch->next_slot ^= 1;
-}
-
-static void choose_buffer_xfer(struct m2p_channel *ch)
-{
- struct ep93xx_dma_buffer *buf;
-
- ch->buffer_xfer = NULL;
- if (!list_empty(&ch->buffers_pending)) {
- buf = list_entry(ch->buffers_pending.next,
- struct ep93xx_dma_buffer, list);
- list_del(&buf->list);
- feed_buf(ch, buf);
- ch->buffer_xfer = buf;
- }
-}
-
-static void choose_buffer_next(struct m2p_channel *ch)
-{
- struct ep93xx_dma_buffer *buf;
-
- ch->buffer_next = NULL;
- if (!list_empty(&ch->buffers_pending)) {
- buf = list_entry(ch->buffers_pending.next,
- struct ep93xx_dma_buffer, list);
- list_del(&buf->list);
- feed_buf(ch, buf);
- ch->buffer_next = buf;
- }
-}
-
-static inline void m2p_set_control(struct m2p_channel *ch, u32 v)
-{
- /*
- * The control register must be read immediately after being written so
- * that the internal state machine is correctly updated. See the ep93xx
- * users' guide for details.
- */
- writel(v, ch->base + M2P_CONTROL);
- readl(ch->base + M2P_CONTROL);
-}
-
-static inline int m2p_channel_state(struct m2p_channel *ch)
-{
- return (readl(ch->base + M2P_STATUS) >> 4) & 0x3;
-}
-
-static irqreturn_t m2p_irq(int irq, void *dev_id)
-{
- struct m2p_channel *ch = dev_id;
- struct ep93xx_dma_m2p_client *cl;
- u32 irq_status, v;
- int error = 0;
-
- cl = ch->client;
-
- spin_lock(&ch->lock);
- irq_status = readl(ch->base + M2P_INTERRUPT);
-
- if (irq_status & M2P_INTERRUPT_ERROR) {
- writel(M2P_INTERRUPT_ERROR, ch->base + M2P_INTERRUPT);
- error = 1;
- }
-
- if ((irq_status & (M2P_INTERRUPT_STALL | M2P_INTERRUPT_NFB)) == 0) {
- spin_unlock(&ch->lock);
- return IRQ_NONE;
- }
-
- switch (m2p_channel_state(ch)) {
- case STATE_IDLE:
- pr_crit("dma interrupt without a dma buffer\n");
- BUG();
- break;
-
- case STATE_STALL:
- cl->buffer_finished(cl->cookie, ch->buffer_xfer, 0, error);
- if (ch->buffer_next != NULL) {
- cl->buffer_finished(cl->cookie, ch->buffer_next,
- 0, error);
- }
- choose_buffer_xfer(ch);
- choose_buffer_next(ch);
- if (ch->buffer_xfer != NULL)
- cl->buffer_started(cl->cookie, ch->buffer_xfer);
- break;
-
- case STATE_ON:
- cl->buffer_finished(cl->cookie, ch->buffer_xfer, 0, error);
- ch->buffer_xfer = ch->buffer_next;
- choose_buffer_next(ch);
- cl->buffer_started(cl->cookie, ch->buffer_xfer);
- break;
-
- case STATE_NEXT:
- pr_crit("dma interrupt while next\n");
- BUG();
- break;
- }
-
- v = readl(ch->base + M2P_CONTROL) & ~(M2P_CONTROL_STALL_IRQ_EN |
- M2P_CONTROL_NFB_IRQ_EN);
- if (ch->buffer_xfer != NULL)
- v |= M2P_CONTROL_STALL_IRQ_EN;
- if (ch->buffer_next != NULL)
- v |= M2P_CONTROL_NFB_IRQ_EN;
- m2p_set_control(ch, v);
-
- spin_unlock(&ch->lock);
- return IRQ_HANDLED;
-}
-
-static struct m2p_channel *find_free_channel(struct ep93xx_dma_m2p_client *cl)
-{
- struct m2p_channel *ch;
- int i;
-
- if (cl->flags & EP93XX_DMA_M2P_RX)
- ch = m2p_rx;
- else
- ch = m2p_tx;
-
- for (i = 0; ch[i].base; i++) {
- struct ep93xx_dma_m2p_client *client;
-
- client = ch[i].client;
- if (client != NULL) {
- int port;
-
- port = cl->flags & EP93XX_DMA_M2P_PORT_MASK;
- if (port == (client->flags &
- EP93XX_DMA_M2P_PORT_MASK)) {
- pr_warning("DMA channel already used by %s\n",
- cl->name ? : "unknown client");
- return ERR_PTR(-EBUSY);
- }
- }
- }
-
- for (i = 0; ch[i].base; i++) {
- if (ch[i].client == NULL)
- return ch + i;
- }
-
- pr_warning("No free DMA channel for %s\n",
- cl->name ? : "unknown client");
- return ERR_PTR(-ENODEV);
-}
-
-static void channel_enable(struct m2p_channel *ch)
-{
- struct ep93xx_dma_m2p_client *cl = ch->client;
- u32 v;
-
- clk_enable(ch->clk);
-
- v = cl->flags & EP93XX_DMA_M2P_PORT_MASK;
- writel(v, ch->base + M2P_PPALLOC);
-
- v = cl->flags & EP93XX_DMA_M2P_ERROR_MASK;
- v |= M2P_CONTROL_ENABLE | M2P_CONTROL_ERROR_IRQ_EN;
- m2p_set_control(ch, v);
-}
-
-static void channel_disable(struct m2p_channel *ch)
-{
- u32 v;
-
- v = readl(ch->base + M2P_CONTROL);
- v &= ~(M2P_CONTROL_STALL_IRQ_EN | M2P_CONTROL_NFB_IRQ_EN);
- m2p_set_control(ch, v);
-
- while (m2p_channel_state(ch) >= STATE_ON)
- cpu_relax();
-
- m2p_set_control(ch, 0x0);
-
- while (m2p_channel_state(ch) == STATE_STALL)
- cpu_relax();
-
- clk_disable(ch->clk);
-}
-
-int ep93xx_dma_m2p_client_register(struct ep93xx_dma_m2p_client *cl)
-{
- struct m2p_channel *ch;
- int err;
-
- ch = find_free_channel(cl);
- if (IS_ERR(ch))
- return PTR_ERR(ch);
-
- err = request_irq(ch->irq, m2p_irq, 0, cl->name ? : "dma-m2p", ch);
- if (err)
- return err;
-
- ch->client = cl;
- ch->next_slot = 0;
- ch->buffer_xfer = NULL;
- ch->buffer_next = NULL;
- INIT_LIST_HEAD(&ch->buffers_pending);
-
- cl->channel = ch;
-
- channel_enable(ch);
-
- return 0;
-}
-EXPORT_SYMBOL_GPL(ep93xx_dma_m2p_client_register);
-
-void ep93xx_dma_m2p_client_unregister(struct ep93xx_dma_m2p_client *cl)
-{
- struct m2p_channel *ch = cl->channel;
-
- channel_disable(ch);
- free_irq(ch->irq, ch);
- ch->client = NULL;
-}
-EXPORT_SYMBOL_GPL(ep93xx_dma_m2p_client_unregister);
-
-void ep93xx_dma_m2p_submit(struct ep93xx_dma_m2p_client *cl,
- struct ep93xx_dma_buffer *buf)
-{
- struct m2p_channel *ch = cl->channel;
- unsigned long flags;
- u32 v;
-
- spin_lock_irqsave(&ch->lock, flags);
- v = readl(ch->base + M2P_CONTROL);
- if (ch->buffer_xfer == NULL) {
- ch->buffer_xfer = buf;
- feed_buf(ch, buf);
- cl->buffer_started(cl->cookie, buf);
-
- v |= M2P_CONTROL_STALL_IRQ_EN;
- m2p_set_control(ch, v);
-
- } else if (ch->buffer_next == NULL) {
- ch->buffer_next = buf;
- feed_buf(ch, buf);
-
- v |= M2P_CONTROL_NFB_IRQ_EN;
- m2p_set_control(ch, v);
- } else {
- list_add_tail(&buf->list, &ch->buffers_pending);
- }
- spin_unlock_irqrestore(&ch->lock, flags);
-}
-EXPORT_SYMBOL_GPL(ep93xx_dma_m2p_submit);
-
-void ep93xx_dma_m2p_submit_recursive(struct ep93xx_dma_m2p_client *cl,
- struct ep93xx_dma_buffer *buf)
-{
- struct m2p_channel *ch = cl->channel;
-
- list_add_tail(&buf->list, &ch->buffers_pending);
-}
-EXPORT_SYMBOL_GPL(ep93xx_dma_m2p_submit_recursive);
-
-void ep93xx_dma_m2p_flush(struct ep93xx_dma_m2p_client *cl)
-{
- struct m2p_channel *ch = cl->channel;
-
- channel_disable(ch);
- ch->next_slot = 0;
- ch->buffer_xfer = NULL;
- ch->buffer_next = NULL;
- INIT_LIST_HEAD(&ch->buffers_pending);
- channel_enable(ch);
-}
-EXPORT_SYMBOL_GPL(ep93xx_dma_m2p_flush);
-
-static int init_channel(struct m2p_channel *ch)
-{
- ch->clk = clk_get(NULL, ch->name);
- if (IS_ERR(ch->clk))
- return PTR_ERR(ch->clk);
-
- spin_lock_init(&ch->lock);
- ch->client = NULL;
-
- return 0;
-}
-
-static int __init ep93xx_dma_m2p_init(void)
-{
- int i;
- int ret;
-
- for (i = 0; m2p_rx[i].base; i++) {
- ret = init_channel(m2p_rx + i);
- if (ret)
- return ret;
- }
-
- for (i = 0; m2p_tx[i].base; i++) {
- ret = init_channel(m2p_tx + i);
- if (ret)
- return ret;
- }
-
- pr_info("M2P DMA subsystem initialized\n");
- return 0;
-}
-arch_initcall(ep93xx_dma_m2p_init);
diff --git a/arch/arm/mach-ep93xx/dma.c b/arch/arm/mach-ep93xx/dma.c
new file mode 100644
index 0000000..5a25708
--- /dev/null
+++ b/arch/arm/mach-ep93xx/dma.c
@@ -0,0 +1,108 @@
+/*
+ * arch/arm/mach-ep93xx/dma.c
+ *
+ * Platform support code for the EP93xx dmaengine driver.
+ *
+ * Copyright (C) 2011 Mika Westerberg
+ *
+ * This work is based on the original dma-m2p implementation with
+ * following copyrights:
+ *
+ * Copyright (C) 2006 Lennert Buytenhek <buytenh@wantstofly.org>
+ * Copyright (C) 2006 Applied Data Systems
+ * Copyright (C) 2009 Ryan Mallon <rmallon@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or (at
+ * your option) any later version.
+ */
+
+#include <linux/dmaengine.h>
+#include <linux/dma-mapping.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+
+#include <mach/dma.h>
+#include <mach/hardware.h>
+
+#define DMA_CHANNEL(_name, _base, _irq) \
+ { .name = (_name), .base = (_base), .irq = (_irq) }
+
+/*
+ * DMA M2P channels.
+ *
+ * On the EP93xx chip the following peripherals my be allocated to the 10
+ * Memory to Internal Peripheral (M2P) channels (5 transmit + 5 receive).
+ *
+ * I2S contains 3 Tx and 3 Rx DMA Channels
+ * AAC contains 3 Tx and 3 Rx DMA Channels
+ * UART1 contains 1 Tx and 1 Rx DMA Channels
+ * UART2 contains 1 Tx and 1 Rx DMA Channels
+ * UART3 contains 1 Tx and 1 Rx DMA Channels
+ * IrDA contains 1 Tx and 1 Rx DMA Channels
+ *
+ * Registers are mapped statically in ep93xx_map_io().
+ */
+static struct ep93xx_dma_chan_data ep93xx_dma_m2p_channels[] = {
+ DMA_CHANNEL("m2p0", EP93XX_DMA_BASE + 0x0000, IRQ_EP93XX_DMAM2P0),
+ DMA_CHANNEL("m2p1", EP93XX_DMA_BASE + 0x0040, IRQ_EP93XX_DMAM2P1),
+ DMA_CHANNEL("m2p2", EP93XX_DMA_BASE + 0x0080, IRQ_EP93XX_DMAM2P2),
+ DMA_CHANNEL("m2p3", EP93XX_DMA_BASE + 0x00c0, IRQ_EP93XX_DMAM2P3),
+ DMA_CHANNEL("m2p4", EP93XX_DMA_BASE + 0x0240, IRQ_EP93XX_DMAM2P4),
+ DMA_CHANNEL("m2p5", EP93XX_DMA_BASE + 0x0200, IRQ_EP93XX_DMAM2P5),
+ DMA_CHANNEL("m2p6", EP93XX_DMA_BASE + 0x02c0, IRQ_EP93XX_DMAM2P6),
+ DMA_CHANNEL("m2p7", EP93XX_DMA_BASE + 0x0280, IRQ_EP93XX_DMAM2P7),
+ DMA_CHANNEL("m2p8", EP93XX_DMA_BASE + 0x0340, IRQ_EP93XX_DMAM2P8),
+ DMA_CHANNEL("m2p9", EP93XX_DMA_BASE + 0x0300, IRQ_EP93XX_DMAM2P9),
+};
+
+static struct ep93xx_dma_platform_data ep93xx_dma_m2p_data = {
+ .channels = ep93xx_dma_m2p_channels,
+ .num_channels = ARRAY_SIZE(ep93xx_dma_m2p_channels),
+};
+
+static struct platform_device ep93xx_dma_m2p_device = {
+ .name = "ep93xx-dma-m2p",
+ .id = -1,
+ .dev = {
+ .platform_data = &ep93xx_dma_m2p_data,
+ },
+};
+
+/*
+ * DMA M2M channels.
+ *
+ * There are 2 M2M channels which support memcpy/memset and in addition simple
+ * hardware requests from/to SSP and IDE. We do not implement an external
+ * hardware requests.
+ *
+ * Registers are mapped statically in ep93xx_map_io().
+ */
+static struct ep93xx_dma_chan_data ep93xx_dma_m2m_channels[] = {
+ DMA_CHANNEL("m2m0", EP93XX_DMA_BASE + 0x0100, IRQ_EP93XX_DMAM2M0),
+ DMA_CHANNEL("m2m1", EP93XX_DMA_BASE + 0x0140, IRQ_EP93XX_DMAM2M1),
+};
+
+static struct ep93xx_dma_platform_data ep93xx_dma_m2m_data = {
+ .channels = ep93xx_dma_m2m_channels,
+ .num_channels = ARRAY_SIZE(ep93xx_dma_m2m_channels),
+};
+
+static struct platform_device ep93xx_dma_m2m_device = {
+ .name = "ep93xx-dma-m2m",
+ .id = -1,
+ .dev = {
+ .platform_data = &ep93xx_dma_m2m_data,
+ },
+};
+
+static int __init ep93xx_dma_init(void)
+{
+ platform_device_register(&ep93xx_dma_m2p_device);
+ platform_device_register(&ep93xx_dma_m2m_device);
+ return 0;
+}
+arch_initcall(ep93xx_dma_init);
diff --git a/arch/arm/mach-ep93xx/include/mach/dma.h b/arch/arm/mach-ep93xx/include/mach/dma.h
index 5e31b2b..46d4d87 100644
--- a/arch/arm/mach-ep93xx/include/mach/dma.h
+++ b/arch/arm/mach-ep93xx/include/mach/dma.h
@@ -1,149 +1,93 @@
-/**
- * DOC: EP93xx DMA M2P memory to peripheral and peripheral to memory engine
- *
- * The EP93xx DMA M2P subsystem handles DMA transfers between memory and
- * peripherals. DMA M2P channels are available for audio, UARTs and IrDA.
- * See chapter 10 of the EP93xx users guide for full details on the DMA M2P
- * engine.
- *
- * See sound/soc/ep93xx/ep93xx-pcm.c for an example use of the DMA M2P code.
- *
- */
-
#ifndef __ASM_ARCH_DMA_H
#define __ASM_ARCH_DMA_H
-#include <linux/list.h>
#include <linux/types.h>
-
-/**
- * struct ep93xx_dma_buffer - Information about a buffer to be transferred
- * using the DMA M2P engine
- *
- * @list: Entry in DMA buffer list
- * @bus_addr: Physical address of the buffer
- * @size: Size of the buffer in bytes
- */
-struct ep93xx_dma_buffer {
- struct list_head list;
- u32 bus_addr;
- u16 size;
-};
-
-/**
- * struct ep93xx_dma_m2p_client - Information about a DMA M2P client
- *
- * @name: Unique name for this client
- * @flags: Client flags
- * @cookie: User data to pass to callback functions
- * @buffer_started: Non NULL function to call when a transfer is started.
- * The arguments are the user data cookie and the DMA
- * buffer which is starting.
- * @buffer_finished: Non NULL function to call when a transfer is completed.
- * The arguments are the user data cookie, the DMA buffer
- * which has completed, and a boolean flag indicating if
- * the transfer had an error.
- */
-struct ep93xx_dma_m2p_client {
- char *name;
- u8 flags;
- void *cookie;
- void (*buffer_started)(void *cookie,
- struct ep93xx_dma_buffer *buf);
- void (*buffer_finished)(void *cookie,
- struct ep93xx_dma_buffer *buf,
- int bytes, int error);
-
- /* private: Internal use only */
- void *channel;
-};
-
-/* DMA M2P ports */
-#define EP93XX_DMA_M2P_PORT_I2S1 0x00
-#define EP93XX_DMA_M2P_PORT_I2S2 0x01
-#define EP93XX_DMA_M2P_PORT_AAC1 0x02
-#define EP93XX_DMA_M2P_PORT_AAC2 0x03
-#define EP93XX_DMA_M2P_PORT_AAC3 0x04
-#define EP93XX_DMA_M2P_PORT_I2S3 0x05
-#define EP93XX_DMA_M2P_PORT_UART1 0x06
-#define EP93XX_DMA_M2P_PORT_UART2 0x07
-#define EP93XX_DMA_M2P_PORT_UART3 0x08
-#define EP93XX_DMA_M2P_PORT_IRDA 0x09
-#define EP93XX_DMA_M2P_PORT_MASK 0x0f
-
-/* DMA M2P client flags */
-#define EP93XX_DMA_M2P_TX 0x00 /* Memory to peripheral */
-#define EP93XX_DMA_M2P_RX 0x10 /* Peripheral to memory */
+#include <linux/dmaengine.h>
+#include <linux/dma-mapping.h>
/*
- * DMA M2P client error handling flags. See the EP93xx users guide
- * documentation on the DMA M2P CONTROL register for more details
+ * M2P channels.
+ *
+ * Note that these values are also directly used for setting the PPALLOC
+ * register.
*/
-#define EP93XX_DMA_M2P_ABORT_ON_ERROR 0x20 /* Abort on peripheral error */
-#define EP93XX_DMA_M2P_IGNORE_ERROR 0x40 /* Ignore peripheral errors */
-#define EP93XX_DMA_M2P_ERROR_MASK 0x60 /* Mask of error bits */
+#define EP93XX_DMA_I2S1 0
+#define EP93XX_DMA_I2S2 1
+#define EP93XX_DMA_AAC1 2
+#define EP93XX_DMA_AAC2 3
+#define EP93XX_DMA_AAC3 4
+#define EP93XX_DMA_I2S3 5
+#define EP93XX_DMA_UART1 6
+#define EP93XX_DMA_UART2 7
+#define EP93XX_DMA_UART3 8
+#define EP93XX_DMA_IRDA 9
+/* M2M channels */
+#define EP93XX_DMA_SSP 10
+#define EP93XX_DMA_IDE 11
/**
- * ep93xx_dma_m2p_client_register - Register a client with the DMA M2P
- * subsystem
+ * struct ep93xx_dma_data - configuration data for the EP93xx dmaengine
+ * @port: peripheral which is requesting the channel
+ * @direction: TX/RX channel
+ * @name: optional name for the channel, this is displayed in /proc/interrupts
*
- * @m2p: Client information to register
- * returns 0 on success
- *
- * The DMA M2P subsystem allocates a channel and an interrupt line for the DMA
- * client
+ * This information is passed as private channel parameter in a filter
+ * function. Note that this is only needed for slave/cyclic channels. For
+ * memcpy channels %NULL data should be passed.
*/
-int ep93xx_dma_m2p_client_register(struct ep93xx_dma_m2p_client *m2p);
+struct ep93xx_dma_data {
+ int port;
+ enum dma_data_direction direction;
+ const char *name;
+};
/**
- * ep93xx_dma_m2p_client_unregister - Unregister a client from the DMA M2P
- * subsystem
- *
- * @m2p: Client to unregister
- *
- * Any transfers currently in progress will be completed in hardware, but
- * ignored in software.
+ * struct ep93xx_dma_chan_data - platform specific data for a DMA channel
+ * @name: name of the channel, used for getting the right clock for the channel
+ * @base: mapped registers
+ * @irq: interrupt number used by this channel
*/
-void ep93xx_dma_m2p_client_unregister(struct ep93xx_dma_m2p_client *m2p);
+struct ep93xx_dma_chan_data {
+ const char *name;
+ void __iomem *base;
+ int irq;
+};
/**
- * ep93xx_dma_m2p_submit - Submit a DMA M2P transfer
+ * struct ep93xx_dma_platform_data - platform data for the dmaengine driver
+ * @channels: array of channels which are passed to the driver
+ * @num_channels: number of channels in the array
*
- * @m2p: DMA Client to submit the transfer on
- * @buf: DMA Buffer to submit
- *
- * If the current or next transfer positions are free on the M2P client then
- * the transfer is started immediately. If not, the transfer is added to the
- * list of pending transfers. This function must not be called from the
- * buffer_finished callback for an M2P channel.
- *
+ * This structure is passed to the DMA engine driver via platform data. For
+ * M2P channels, contract is that even channels are for TX and odd for RX.
+ * There is no requirement for the M2M channels.
*/
-void ep93xx_dma_m2p_submit(struct ep93xx_dma_m2p_client *m2p,
- struct ep93xx_dma_buffer *buf);
+struct ep93xx_dma_platform_data {
+ struct ep93xx_dma_chan_data *channels;
+ size_t num_channels;
+};
+
+static inline bool ep93xx_dma_chan_is_m2p(struct dma_chan *chan)
+{
+ return !strcmp(dev_name(chan->device->dev), "ep93xx-dma-m2p");
+}
/**
- * ep93xx_dma_m2p_submit_recursive - Put a DMA transfer on the pending list
- * for an M2P channel
+ * ep93xx_dma_chan_direction - returns direction the channel can be used
+ * @chan: channel
*
- * @m2p: DMA Client to submit the transfer on
- * @buf: DMA Buffer to submit
- *
- * This function must only be called from the buffer_finished callback for an
- * M2P channel. It is commonly used to add the next transfer in a chained list
- * of DMA transfers.
+ * This function can be used in filter functions to find out whether the
+ * channel supports given DMA direction. Only M2P channels have such
+ * limitation, for M2M channels the direction is configurable.
*/
-void ep93xx_dma_m2p_submit_recursive(struct ep93xx_dma_m2p_client *m2p,
- struct ep93xx_dma_buffer *buf);
+static inline enum dma_data_direction
+ep93xx_dma_chan_direction(struct dma_chan *chan)
+{
+ if (!ep93xx_dma_chan_is_m2p(chan))
+ return DMA_NONE;
-/**
- * ep93xx_dma_m2p_flush - Flush all pending transfers on a DMA M2P client
- *
- * @m2p: DMA client to flush transfers on
- *
- * Any transfers currently in progress will be completed in hardware, but
- * ignored in software.
- *
- */
-void ep93xx_dma_m2p_flush(struct ep93xx_dma_m2p_client *m2p);
+ /* even channels are for TX, odd for RX */
+ return (chan->chan_id % 2 == 0) ? DMA_TO_DEVICE : DMA_FROM_DEVICE;
+}
#endif /* __ASM_ARCH_DMA_H */
diff --git a/arch/arm/mach-ep93xx/include/mach/ep93xx_spi.h b/arch/arm/mach-ep93xx/include/mach/ep93xx_spi.h
index 0a37961..9bb63ac 100644
--- a/arch/arm/mach-ep93xx/include/mach/ep93xx_spi.h
+++ b/arch/arm/mach-ep93xx/include/mach/ep93xx_spi.h
@@ -7,9 +7,11 @@
* struct ep93xx_spi_info - EP93xx specific SPI descriptor
* @num_chipselect: number of chip selects on this board, must be
* at least one
+ * @use_dma: use DMA for the transfers
*/
struct ep93xx_spi_info {
int num_chipselect;
+ bool use_dma;
};
/**
diff --git a/drivers/dma/Kconfig b/drivers/dma/Kconfig
index 25cf327..2e3b3d3 100644
--- a/drivers/dma/Kconfig
+++ b/drivers/dma/Kconfig
@@ -237,6 +237,13 @@
Support the MXS DMA engine. This engine including APBH-DMA
and APBX-DMA is integrated into Freescale i.MX23/28 chips.
+config EP93XX_DMA
+ bool "Cirrus Logic EP93xx DMA support"
+ depends on ARCH_EP93XX
+ select DMA_ENGINE
+ help
+ Enable support for the Cirrus Logic EP93xx M2P/M2M DMA controller.
+
config DMA_ENGINE
bool
diff --git a/drivers/dma/Makefile b/drivers/dma/Makefile
index 836095a..30cf3b1 100644
--- a/drivers/dma/Makefile
+++ b/drivers/dma/Makefile
@@ -25,3 +25,4 @@
obj-$(CONFIG_PL330_DMA) += pl330.o
obj-$(CONFIG_PCH_DMA) += pch_dma.o
obj-$(CONFIG_AMBA_PL08X) += amba-pl08x.o
+obj-$(CONFIG_EP93XX_DMA) += ep93xx_dma.o
diff --git a/drivers/dma/TODO b/drivers/dma/TODO
index a4af858..734ed02 100644
--- a/drivers/dma/TODO
+++ b/drivers/dma/TODO
@@ -9,6 +9,5 @@
- mxs-dma.c
- dw_dmac
- intel_mid_dma
- - ste_dma40
4. Check other subsystems for dma drivers and merge/move to dmaengine
5. Remove dma_slave_config's dma direction.
diff --git a/drivers/dma/amba-pl08x.c b/drivers/dma/amba-pl08x.c
index e6d7228..196a737 100644
--- a/drivers/dma/amba-pl08x.c
+++ b/drivers/dma/amba-pl08x.c
@@ -156,14 +156,10 @@
#define PL08X_BOUNDARY_SHIFT (10) /* 1KB 0x400 */
#define PL08X_BOUNDARY_SIZE (1 << PL08X_BOUNDARY_SHIFT)
-/* Minimum period between work queue runs */
-#define PL08X_WQ_PERIODMIN 20
-
/* Size (bytes) of each LLI buffer allocated for one transfer */
# define PL08X_LLI_TSFR_SIZE 0x2000
/* Maximum times we call dma_pool_alloc on this pool without freeing */
-#define PL08X_MAX_ALLOCS 0x40
#define MAX_NUM_TSFR_LLIS (PL08X_LLI_TSFR_SIZE/sizeof(struct pl08x_lli))
#define PL08X_ALIGN 8
@@ -495,10 +491,10 @@
struct pl08x_lli_build_data {
struct pl08x_txd *txd;
- struct pl08x_driver_data *pl08x;
struct pl08x_bus_data srcbus;
struct pl08x_bus_data dstbus;
size_t remainder;
+ u32 lli_bus;
};
/*
@@ -551,8 +547,7 @@
llis_va[num_llis].src = bd->srcbus.addr;
llis_va[num_llis].dst = bd->dstbus.addr;
llis_va[num_llis].lli = llis_bus + (num_llis + 1) * sizeof(struct pl08x_lli);
- if (bd->pl08x->lli_buses & PL08X_AHB2)
- llis_va[num_llis].lli |= PL080_LLI_LM_AHB2;
+ llis_va[num_llis].lli |= bd->lli_bus;
if (cctl & PL080_CONTROL_SRC_INCR)
bd->srcbus.addr += len;
@@ -605,9 +600,9 @@
cctl = txd->cctl;
bd.txd = txd;
- bd.pl08x = pl08x;
bd.srcbus.addr = txd->src_addr;
bd.dstbus.addr = txd->dst_addr;
+ bd.lli_bus = (pl08x->lli_buses & PL08X_AHB2) ? PL080_LLI_LM_AHB2 : 0;
/* Find maximum width of the source bus */
bd.srcbus.maxwidth =
@@ -622,25 +617,15 @@
/* Set up the bus widths to the maximum */
bd.srcbus.buswidth = bd.srcbus.maxwidth;
bd.dstbus.buswidth = bd.dstbus.maxwidth;
- dev_vdbg(&pl08x->adev->dev,
- "%s source bus is %d bytes wide, dest bus is %d bytes wide\n",
- __func__, bd.srcbus.buswidth, bd.dstbus.buswidth);
-
/*
* Bytes transferred == tsize * MIN(buswidths), not max(buswidths)
*/
max_bytes_per_lli = min(bd.srcbus.buswidth, bd.dstbus.buswidth) *
PL080_CONTROL_TRANSFER_SIZE_MASK;
- dev_vdbg(&pl08x->adev->dev,
- "%s max bytes per lli = %zu\n",
- __func__, max_bytes_per_lli);
/* We need to count this down to zero */
bd.remainder = txd->len;
- dev_vdbg(&pl08x->adev->dev,
- "%s remainder = %zu\n",
- __func__, bd.remainder);
/*
* Choose bus to align to
@@ -649,6 +634,16 @@
*/
pl08x_choose_master_bus(&bd, &mbus, &sbus, cctl);
+ dev_vdbg(&pl08x->adev->dev, "src=0x%08x%s/%u dst=0x%08x%s/%u len=%zu llimax=%zu\n",
+ bd.srcbus.addr, cctl & PL080_CONTROL_SRC_INCR ? "+" : "",
+ bd.srcbus.buswidth,
+ bd.dstbus.addr, cctl & PL080_CONTROL_DST_INCR ? "+" : "",
+ bd.dstbus.buswidth,
+ bd.remainder, max_bytes_per_lli);
+ dev_vdbg(&pl08x->adev->dev, "mbus=%s sbus=%s\n",
+ mbus == &bd.srcbus ? "src" : "dst",
+ sbus == &bd.srcbus ? "src" : "dst");
+
if (txd->len < mbus->buswidth) {
/* Less than a bus width available - send as single bytes */
while (bd.remainder) {
@@ -840,15 +835,14 @@
{
int i;
+ dev_vdbg(&pl08x->adev->dev,
+ "%-3s %-9s %-10s %-10s %-10s %s\n",
+ "lli", "", "csrc", "cdst", "clli", "cctl");
for (i = 0; i < num_llis; i++) {
dev_vdbg(&pl08x->adev->dev,
- "lli %d @%p: csrc=0x%08x, cdst=0x%08x, cctl=0x%08x, clli=0x%08x\n",
- i,
- &llis_va[i],
- llis_va[i].src,
- llis_va[i].dst,
- llis_va[i].cctl,
- llis_va[i].lli
+ "%3d @%p: 0x%08x 0x%08x 0x%08x 0x%08x\n",
+ i, &llis_va[i], llis_va[i].src,
+ llis_va[i].dst, llis_va[i].lli, llis_va[i].cctl
);
}
}
@@ -1054,64 +1048,105 @@
/* PrimeCell DMA extension */
struct burst_table {
- int burstwords;
+ u32 burstwords;
u32 reg;
};
static const struct burst_table burst_sizes[] = {
{
.burstwords = 256,
- .reg = (PL080_BSIZE_256 << PL080_CONTROL_SB_SIZE_SHIFT) |
- (PL080_BSIZE_256 << PL080_CONTROL_DB_SIZE_SHIFT),
+ .reg = PL080_BSIZE_256,
},
{
.burstwords = 128,
- .reg = (PL080_BSIZE_128 << PL080_CONTROL_SB_SIZE_SHIFT) |
- (PL080_BSIZE_128 << PL080_CONTROL_DB_SIZE_SHIFT),
+ .reg = PL080_BSIZE_128,
},
{
.burstwords = 64,
- .reg = (PL080_BSIZE_64 << PL080_CONTROL_SB_SIZE_SHIFT) |
- (PL080_BSIZE_64 << PL080_CONTROL_DB_SIZE_SHIFT),
+ .reg = PL080_BSIZE_64,
},
{
.burstwords = 32,
- .reg = (PL080_BSIZE_32 << PL080_CONTROL_SB_SIZE_SHIFT) |
- (PL080_BSIZE_32 << PL080_CONTROL_DB_SIZE_SHIFT),
+ .reg = PL080_BSIZE_32,
},
{
.burstwords = 16,
- .reg = (PL080_BSIZE_16 << PL080_CONTROL_SB_SIZE_SHIFT) |
- (PL080_BSIZE_16 << PL080_CONTROL_DB_SIZE_SHIFT),
+ .reg = PL080_BSIZE_16,
},
{
.burstwords = 8,
- .reg = (PL080_BSIZE_8 << PL080_CONTROL_SB_SIZE_SHIFT) |
- (PL080_BSIZE_8 << PL080_CONTROL_DB_SIZE_SHIFT),
+ .reg = PL080_BSIZE_8,
},
{
.burstwords = 4,
- .reg = (PL080_BSIZE_4 << PL080_CONTROL_SB_SIZE_SHIFT) |
- (PL080_BSIZE_4 << PL080_CONTROL_DB_SIZE_SHIFT),
+ .reg = PL080_BSIZE_4,
},
{
- .burstwords = 1,
- .reg = (PL080_BSIZE_1 << PL080_CONTROL_SB_SIZE_SHIFT) |
- (PL080_BSIZE_1 << PL080_CONTROL_DB_SIZE_SHIFT),
+ .burstwords = 0,
+ .reg = PL080_BSIZE_1,
},
};
+/*
+ * Given the source and destination available bus masks, select which
+ * will be routed to each port. We try to have source and destination
+ * on separate ports, but always respect the allowable settings.
+ */
+static u32 pl08x_select_bus(u8 src, u8 dst)
+{
+ u32 cctl = 0;
+
+ if (!(dst & PL08X_AHB1) || ((dst & PL08X_AHB2) && (src & PL08X_AHB1)))
+ cctl |= PL080_CONTROL_DST_AHB2;
+ if (!(src & PL08X_AHB1) || ((src & PL08X_AHB2) && !(dst & PL08X_AHB2)))
+ cctl |= PL080_CONTROL_SRC_AHB2;
+
+ return cctl;
+}
+
+static u32 pl08x_cctl(u32 cctl)
+{
+ cctl &= ~(PL080_CONTROL_SRC_AHB2 | PL080_CONTROL_DST_AHB2 |
+ PL080_CONTROL_SRC_INCR | PL080_CONTROL_DST_INCR |
+ PL080_CONTROL_PROT_MASK);
+
+ /* Access the cell in privileged mode, non-bufferable, non-cacheable */
+ return cctl | PL080_CONTROL_PROT_SYS;
+}
+
+static u32 pl08x_width(enum dma_slave_buswidth width)
+{
+ switch (width) {
+ case DMA_SLAVE_BUSWIDTH_1_BYTE:
+ return PL080_WIDTH_8BIT;
+ case DMA_SLAVE_BUSWIDTH_2_BYTES:
+ return PL080_WIDTH_16BIT;
+ case DMA_SLAVE_BUSWIDTH_4_BYTES:
+ return PL080_WIDTH_32BIT;
+ default:
+ return ~0;
+ }
+}
+
+static u32 pl08x_burst(u32 maxburst)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(burst_sizes); i++)
+ if (burst_sizes[i].burstwords <= maxburst)
+ break;
+
+ return burst_sizes[i].reg;
+}
+
static int dma_set_runtime_config(struct dma_chan *chan,
struct dma_slave_config *config)
{
struct pl08x_dma_chan *plchan = to_pl08x_chan(chan);
struct pl08x_driver_data *pl08x = plchan->host;
- struct pl08x_channel_data *cd = plchan->cd;
enum dma_slave_buswidth addr_width;
- dma_addr_t addr;
- u32 maxburst;
+ u32 width, burst, maxburst;
u32 cctl = 0;
- int i;
if (!plchan->slave)
return -EINVAL;
@@ -1119,11 +1154,9 @@
/* Transfer direction */
plchan->runtime_direction = config->direction;
if (config->direction == DMA_TO_DEVICE) {
- addr = config->dst_addr;
addr_width = config->dst_addr_width;
maxburst = config->dst_maxburst;
} else if (config->direction == DMA_FROM_DEVICE) {
- addr = config->src_addr;
addr_width = config->src_addr_width;
maxburst = config->src_maxburst;
} else {
@@ -1132,46 +1165,40 @@
return -EINVAL;
}
- switch (addr_width) {
- case DMA_SLAVE_BUSWIDTH_1_BYTE:
- cctl |= (PL080_WIDTH_8BIT << PL080_CONTROL_SWIDTH_SHIFT) |
- (PL080_WIDTH_8BIT << PL080_CONTROL_DWIDTH_SHIFT);
- break;
- case DMA_SLAVE_BUSWIDTH_2_BYTES:
- cctl |= (PL080_WIDTH_16BIT << PL080_CONTROL_SWIDTH_SHIFT) |
- (PL080_WIDTH_16BIT << PL080_CONTROL_DWIDTH_SHIFT);
- break;
- case DMA_SLAVE_BUSWIDTH_4_BYTES:
- cctl |= (PL080_WIDTH_32BIT << PL080_CONTROL_SWIDTH_SHIFT) |
- (PL080_WIDTH_32BIT << PL080_CONTROL_DWIDTH_SHIFT);
- break;
- default:
+ width = pl08x_width(addr_width);
+ if (width == ~0) {
dev_err(&pl08x->adev->dev,
"bad runtime_config: alien address width\n");
return -EINVAL;
}
+ cctl |= width << PL080_CONTROL_SWIDTH_SHIFT;
+ cctl |= width << PL080_CONTROL_DWIDTH_SHIFT;
+
/*
- * Now decide on a maxburst:
* If this channel will only request single transfers, set this
* down to ONE element. Also select one element if no maxburst
* is specified.
*/
- if (plchan->cd->single || maxburst == 0) {
- cctl |= (PL080_BSIZE_1 << PL080_CONTROL_SB_SIZE_SHIFT) |
- (PL080_BSIZE_1 << PL080_CONTROL_DB_SIZE_SHIFT);
+ if (plchan->cd->single)
+ maxburst = 1;
+
+ burst = pl08x_burst(maxburst);
+ cctl |= burst << PL080_CONTROL_SB_SIZE_SHIFT;
+ cctl |= burst << PL080_CONTROL_DB_SIZE_SHIFT;
+
+ if (plchan->runtime_direction == DMA_FROM_DEVICE) {
+ plchan->src_addr = config->src_addr;
+ plchan->src_cctl = pl08x_cctl(cctl) | PL080_CONTROL_DST_INCR |
+ pl08x_select_bus(plchan->cd->periph_buses,
+ pl08x->mem_buses);
} else {
- for (i = 0; i < ARRAY_SIZE(burst_sizes); i++)
- if (burst_sizes[i].burstwords <= maxburst)
- break;
- cctl |= burst_sizes[i].reg;
+ plchan->dst_addr = config->dst_addr;
+ plchan->dst_cctl = pl08x_cctl(cctl) | PL080_CONTROL_SRC_INCR |
+ pl08x_select_bus(pl08x->mem_buses,
+ plchan->cd->periph_buses);
}
- plchan->runtime_addr = addr;
-
- /* Modify the default channel data to fit PrimeCell request */
- cd->cctl = cctl;
-
dev_dbg(&pl08x->adev->dev,
"configured channel %s (%s) for %s, data width %d, "
"maxburst %d words, LE, CCTL=0x%08x\n",
@@ -1270,23 +1297,6 @@
return 0;
}
-/*
- * Given the source and destination available bus masks, select which
- * will be routed to each port. We try to have source and destination
- * on separate ports, but always respect the allowable settings.
- */
-static u32 pl08x_select_bus(struct pl08x_driver_data *pl08x, u8 src, u8 dst)
-{
- u32 cctl = 0;
-
- if (!(dst & PL08X_AHB1) || ((dst & PL08X_AHB2) && (src & PL08X_AHB1)))
- cctl |= PL080_CONTROL_DST_AHB2;
- if (!(src & PL08X_AHB1) || ((src & PL08X_AHB2) && !(dst & PL08X_AHB2)))
- cctl |= PL080_CONTROL_SRC_AHB2;
-
- return cctl;
-}
-
static struct pl08x_txd *pl08x_get_txd(struct pl08x_dma_chan *plchan,
unsigned long flags)
{
@@ -1338,8 +1348,8 @@
txd->cctl |= PL080_CONTROL_SRC_INCR | PL080_CONTROL_DST_INCR;
if (pl08x->vd->dualmaster)
- txd->cctl |= pl08x_select_bus(pl08x,
- pl08x->mem_buses, pl08x->mem_buses);
+ txd->cctl |= pl08x_select_bus(pl08x->mem_buses,
+ pl08x->mem_buses);
ret = pl08x_prep_channel_resources(plchan, txd);
if (ret)
@@ -1356,7 +1366,6 @@
struct pl08x_dma_chan *plchan = to_pl08x_chan(chan);
struct pl08x_driver_data *pl08x = plchan->host;
struct pl08x_txd *txd;
- u8 src_buses, dst_buses;
int ret;
/*
@@ -1390,42 +1399,22 @@
txd->direction = direction;
txd->len = sgl->length;
- txd->cctl = plchan->cd->cctl &
- ~(PL080_CONTROL_SRC_AHB2 | PL080_CONTROL_DST_AHB2 |
- PL080_CONTROL_SRC_INCR | PL080_CONTROL_DST_INCR |
- PL080_CONTROL_PROT_MASK);
-
- /* Access the cell in privileged mode, non-bufferable, non-cacheable */
- txd->cctl |= PL080_CONTROL_PROT_SYS;
-
if (direction == DMA_TO_DEVICE) {
txd->ccfg |= PL080_FLOW_MEM2PER << PL080_CONFIG_FLOW_CONTROL_SHIFT;
- txd->cctl |= PL080_CONTROL_SRC_INCR;
+ txd->cctl = plchan->dst_cctl;
txd->src_addr = sgl->dma_address;
- if (plchan->runtime_addr)
- txd->dst_addr = plchan->runtime_addr;
- else
- txd->dst_addr = plchan->cd->addr;
- src_buses = pl08x->mem_buses;
- dst_buses = plchan->cd->periph_buses;
+ txd->dst_addr = plchan->dst_addr;
} else if (direction == DMA_FROM_DEVICE) {
txd->ccfg |= PL080_FLOW_PER2MEM << PL080_CONFIG_FLOW_CONTROL_SHIFT;
- txd->cctl |= PL080_CONTROL_DST_INCR;
- if (plchan->runtime_addr)
- txd->src_addr = plchan->runtime_addr;
- else
- txd->src_addr = plchan->cd->addr;
+ txd->cctl = plchan->src_cctl;
+ txd->src_addr = plchan->src_addr;
txd->dst_addr = sgl->dma_address;
- src_buses = plchan->cd->periph_buses;
- dst_buses = pl08x->mem_buses;
} else {
dev_err(&pl08x->adev->dev,
"%s direction unsupported\n", __func__);
return NULL;
}
- txd->cctl |= pl08x_select_bus(pl08x, src_buses, dst_buses);
-
ret = pl08x_prep_channel_resources(plchan, txd);
if (ret)
return NULL;
@@ -1676,6 +1665,20 @@
return mask ? IRQ_HANDLED : IRQ_NONE;
}
+static void pl08x_dma_slave_init(struct pl08x_dma_chan *chan)
+{
+ u32 cctl = pl08x_cctl(chan->cd->cctl);
+
+ chan->slave = true;
+ chan->name = chan->cd->bus_id;
+ chan->src_addr = chan->cd->addr;
+ chan->dst_addr = chan->cd->addr;
+ chan->src_cctl = cctl | PL080_CONTROL_DST_INCR |
+ pl08x_select_bus(chan->cd->periph_buses, chan->host->mem_buses);
+ chan->dst_cctl = cctl | PL080_CONTROL_SRC_INCR |
+ pl08x_select_bus(chan->host->mem_buses, chan->cd->periph_buses);
+}
+
/*
* Initialise the DMAC memcpy/slave channels.
* Make a local wrapper to hold required data
@@ -1707,9 +1710,8 @@
chan->state = PL08X_CHAN_IDLE;
if (slave) {
- chan->slave = true;
- chan->name = pl08x->pd->slave_channels[i].bus_id;
chan->cd = &pl08x->pd->slave_channels[i];
+ pl08x_dma_slave_init(chan);
} else {
chan->cd = &pl08x->pd->memcpy_channel;
chan->name = kasprintf(GFP_KERNEL, "memcpy%d", i);
diff --git a/drivers/dma/at_hdmac.c b/drivers/dma/at_hdmac.c
index 36144f8..6a483ea 100644
--- a/drivers/dma/at_hdmac.c
+++ b/drivers/dma/at_hdmac.c
@@ -1216,7 +1216,7 @@
atdma->dma_common.cap_mask = pdata->cap_mask;
atdma->all_chan_mask = (1 << pdata->nr_channels) - 1;
- size = io->end - io->start + 1;
+ size = resource_size(io);
if (!request_mem_region(io->start, size, pdev->dev.driver->name)) {
err = -EBUSY;
goto err_kfree;
@@ -1362,7 +1362,7 @@
atdma->regs = NULL;
io = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- release_mem_region(io->start, io->end - io->start + 1);
+ release_mem_region(io->start, resource_size(io));
kfree(atdma);
diff --git a/drivers/dma/coh901318.c b/drivers/dma/coh901318.c
index af8c0b5..a7fca16 100644
--- a/drivers/dma/coh901318.c
+++ b/drivers/dma/coh901318.c
@@ -40,6 +40,8 @@
struct coh901318_lli *lli;
enum dma_data_direction dir;
unsigned long flags;
+ u32 head_config;
+ u32 head_ctrl;
};
struct coh901318_base {
@@ -660,6 +662,9 @@
coh901318_desc_submit(cohc, cohd);
+ /* Program the transaction head */
+ coh901318_set_conf(cohc, cohd->head_config);
+ coh901318_set_ctrl(cohc, cohd->head_ctrl);
coh901318_prep_linked_list(cohc, cohd->lli);
/* start dma job on this channel */
@@ -1090,8 +1095,6 @@
} else
goto err_direction;
- coh901318_set_conf(cohc, config);
-
/* The dma only supports transmitting packages up to
* MAX_DMA_PACKET_SIZE. Calculate to total number of
* dma elemts required to send the entire sg list
@@ -1128,16 +1131,18 @@
if (ret)
goto err_lli_fill;
- /*
- * Set the default ctrl for the channel to the one from the lli,
- * things may have changed due to odd buffer alignment etc.
- */
- coh901318_set_ctrl(cohc, lli->control);
COH_DBG(coh901318_list_print(cohc, lli));
/* Pick a descriptor to handle this transfer */
cohd = coh901318_desc_get(cohc);
+ cohd->head_config = config;
+ /*
+ * Set the default head ctrl for the channel to the one from the
+ * lli, things may have changed due to odd buffer alignment
+ * etc.
+ */
+ cohd->head_ctrl = lli->control;
cohd->dir = direction;
cohd->flags = flags;
cohd->desc.tx_submit = coh901318_tx_submit;
diff --git a/drivers/dma/dmaengine.c b/drivers/dma/dmaengine.c
index 8bcb15f..f7f21a5 100644
--- a/drivers/dma/dmaengine.c
+++ b/drivers/dma/dmaengine.c
@@ -509,8 +509,8 @@
dma_chan_name(chan));
list_del_rcu(&device->global_node);
} else if (err)
- pr_err("dmaengine: failed to get %s: (%d)\n",
- dma_chan_name(chan), err);
+ pr_debug("dmaengine: failed to get %s: (%d)\n",
+ dma_chan_name(chan), err);
else
break;
if (--device->privatecnt == 0)
diff --git a/drivers/dma/ep93xx_dma.c b/drivers/dma/ep93xx_dma.c
new file mode 100644
index 0000000..5d7a49b
--- /dev/null
+++ b/drivers/dma/ep93xx_dma.c
@@ -0,0 +1,1355 @@
+/*
+ * Driver for the Cirrus Logic EP93xx DMA Controller
+ *
+ * Copyright (C) 2011 Mika Westerberg
+ *
+ * DMA M2P implementation is based on the original
+ * arch/arm/mach-ep93xx/dma-m2p.c which has following copyrights:
+ *
+ * Copyright (C) 2006 Lennert Buytenhek <buytenh@wantstofly.org>
+ * Copyright (C) 2006 Applied Data Systems
+ * Copyright (C) 2009 Ryan Mallon <rmallon@gmail.com>
+ *
+ * This driver is based on dw_dmac and amba-pl08x drivers.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/clk.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/dmaengine.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#include <mach/dma.h>
+
+/* M2P registers */
+#define M2P_CONTROL 0x0000
+#define M2P_CONTROL_STALLINT BIT(0)
+#define M2P_CONTROL_NFBINT BIT(1)
+#define M2P_CONTROL_CH_ERROR_INT BIT(3)
+#define M2P_CONTROL_ENABLE BIT(4)
+#define M2P_CONTROL_ICE BIT(6)
+
+#define M2P_INTERRUPT 0x0004
+#define M2P_INTERRUPT_STALL BIT(0)
+#define M2P_INTERRUPT_NFB BIT(1)
+#define M2P_INTERRUPT_ERROR BIT(3)
+
+#define M2P_PPALLOC 0x0008
+#define M2P_STATUS 0x000c
+
+#define M2P_MAXCNT0 0x0020
+#define M2P_BASE0 0x0024
+#define M2P_MAXCNT1 0x0030
+#define M2P_BASE1 0x0034
+
+#define M2P_STATE_IDLE 0
+#define M2P_STATE_STALL 1
+#define M2P_STATE_ON 2
+#define M2P_STATE_NEXT 3
+
+/* M2M registers */
+#define M2M_CONTROL 0x0000
+#define M2M_CONTROL_DONEINT BIT(2)
+#define M2M_CONTROL_ENABLE BIT(3)
+#define M2M_CONTROL_START BIT(4)
+#define M2M_CONTROL_DAH BIT(11)
+#define M2M_CONTROL_SAH BIT(12)
+#define M2M_CONTROL_PW_SHIFT 9
+#define M2M_CONTROL_PW_8 (0 << M2M_CONTROL_PW_SHIFT)
+#define M2M_CONTROL_PW_16 (1 << M2M_CONTROL_PW_SHIFT)
+#define M2M_CONTROL_PW_32 (2 << M2M_CONTROL_PW_SHIFT)
+#define M2M_CONTROL_PW_MASK (3 << M2M_CONTROL_PW_SHIFT)
+#define M2M_CONTROL_TM_SHIFT 13
+#define M2M_CONTROL_TM_TX (1 << M2M_CONTROL_TM_SHIFT)
+#define M2M_CONTROL_TM_RX (2 << M2M_CONTROL_TM_SHIFT)
+#define M2M_CONTROL_RSS_SHIFT 22
+#define M2M_CONTROL_RSS_SSPRX (1 << M2M_CONTROL_RSS_SHIFT)
+#define M2M_CONTROL_RSS_SSPTX (2 << M2M_CONTROL_RSS_SHIFT)
+#define M2M_CONTROL_RSS_IDE (3 << M2M_CONTROL_RSS_SHIFT)
+#define M2M_CONTROL_NO_HDSK BIT(24)
+#define M2M_CONTROL_PWSC_SHIFT 25
+
+#define M2M_INTERRUPT 0x0004
+#define M2M_INTERRUPT_DONEINT BIT(1)
+
+#define M2M_BCR0 0x0010
+#define M2M_BCR1 0x0014
+#define M2M_SAR_BASE0 0x0018
+#define M2M_SAR_BASE1 0x001c
+#define M2M_DAR_BASE0 0x002c
+#define M2M_DAR_BASE1 0x0030
+
+#define DMA_MAX_CHAN_BYTES 0xffff
+#define DMA_MAX_CHAN_DESCRIPTORS 32
+
+struct ep93xx_dma_engine;
+
+/**
+ * struct ep93xx_dma_desc - EP93xx specific transaction descriptor
+ * @src_addr: source address of the transaction
+ * @dst_addr: destination address of the transaction
+ * @size: size of the transaction (in bytes)
+ * @complete: this descriptor is completed
+ * @txd: dmaengine API descriptor
+ * @tx_list: list of linked descriptors
+ * @node: link used for putting this into a channel queue
+ */
+struct ep93xx_dma_desc {
+ u32 src_addr;
+ u32 dst_addr;
+ size_t size;
+ bool complete;
+ struct dma_async_tx_descriptor txd;
+ struct list_head tx_list;
+ struct list_head node;
+};
+
+/**
+ * struct ep93xx_dma_chan - an EP93xx DMA M2P/M2M channel
+ * @chan: dmaengine API channel
+ * @edma: pointer to to the engine device
+ * @regs: memory mapped registers
+ * @irq: interrupt number of the channel
+ * @clk: clock used by this channel
+ * @tasklet: channel specific tasklet used for callbacks
+ * @lock: lock protecting the fields following
+ * @flags: flags for the channel
+ * @buffer: which buffer to use next (0/1)
+ * @last_completed: last completed cookie value
+ * @active: flattened chain of descriptors currently being processed
+ * @queue: pending descriptors which are handled next
+ * @free_list: list of free descriptors which can be used
+ * @runtime_addr: physical address currently used as dest/src (M2M only). This
+ * is set via %DMA_SLAVE_CONFIG before slave operation is
+ * prepared
+ * @runtime_ctrl: M2M runtime values for the control register.
+ *
+ * As EP93xx DMA controller doesn't support real chained DMA descriptors we
+ * will have slightly different scheme here: @active points to a head of
+ * flattened DMA descriptor chain.
+ *
+ * @queue holds pending transactions. These are linked through the first
+ * descriptor in the chain. When a descriptor is moved to the @active queue,
+ * the first and chained descriptors are flattened into a single list.
+ *
+ * @chan.private holds pointer to &struct ep93xx_dma_data which contains
+ * necessary channel configuration information. For memcpy channels this must
+ * be %NULL.
+ */
+struct ep93xx_dma_chan {
+ struct dma_chan chan;
+ const struct ep93xx_dma_engine *edma;
+ void __iomem *regs;
+ int irq;
+ struct clk *clk;
+ struct tasklet_struct tasklet;
+ /* protects the fields following */
+ spinlock_t lock;
+ unsigned long flags;
+/* Channel is configured for cyclic transfers */
+#define EP93XX_DMA_IS_CYCLIC 0
+
+ int buffer;
+ dma_cookie_t last_completed;
+ struct list_head active;
+ struct list_head queue;
+ struct list_head free_list;
+ u32 runtime_addr;
+ u32 runtime_ctrl;
+};
+
+/**
+ * struct ep93xx_dma_engine - the EP93xx DMA engine instance
+ * @dma_dev: holds the dmaengine device
+ * @m2m: is this an M2M or M2P device
+ * @hw_setup: method which sets the channel up for operation
+ * @hw_shutdown: shuts the channel down and flushes whatever is left
+ * @hw_submit: pushes active descriptor(s) to the hardware
+ * @hw_interrupt: handle the interrupt
+ * @num_channels: number of channels for this instance
+ * @channels: array of channels
+ *
+ * There is one instance of this struct for the M2P channels and one for the
+ * M2M channels. hw_xxx() methods are used to perform operations which are
+ * different on M2M and M2P channels. These methods are called with channel
+ * lock held and interrupts disabled so they cannot sleep.
+ */
+struct ep93xx_dma_engine {
+ struct dma_device dma_dev;
+ bool m2m;
+ int (*hw_setup)(struct ep93xx_dma_chan *);
+ void (*hw_shutdown)(struct ep93xx_dma_chan *);
+ void (*hw_submit)(struct ep93xx_dma_chan *);
+ int (*hw_interrupt)(struct ep93xx_dma_chan *);
+#define INTERRUPT_UNKNOWN 0
+#define INTERRUPT_DONE 1
+#define INTERRUPT_NEXT_BUFFER 2
+
+ size_t num_channels;
+ struct ep93xx_dma_chan channels[];
+};
+
+static inline struct device *chan2dev(struct ep93xx_dma_chan *edmac)
+{
+ return &edmac->chan.dev->device;
+}
+
+static struct ep93xx_dma_chan *to_ep93xx_dma_chan(struct dma_chan *chan)
+{
+ return container_of(chan, struct ep93xx_dma_chan, chan);
+}
+
+/**
+ * ep93xx_dma_set_active - set new active descriptor chain
+ * @edmac: channel
+ * @desc: head of the new active descriptor chain
+ *
+ * Sets @desc to be the head of the new active descriptor chain. This is the
+ * chain which is processed next. The active list must be empty before calling
+ * this function.
+ *
+ * Called with @edmac->lock held and interrupts disabled.
+ */
+static void ep93xx_dma_set_active(struct ep93xx_dma_chan *edmac,
+ struct ep93xx_dma_desc *desc)
+{
+ BUG_ON(!list_empty(&edmac->active));
+
+ list_add_tail(&desc->node, &edmac->active);
+
+ /* Flatten the @desc->tx_list chain into @edmac->active list */
+ while (!list_empty(&desc->tx_list)) {
+ struct ep93xx_dma_desc *d = list_first_entry(&desc->tx_list,
+ struct ep93xx_dma_desc, node);
+
+ /*
+ * We copy the callback parameters from the first descriptor
+ * to all the chained descriptors. This way we can call the
+ * callback without having to find out the first descriptor in
+ * the chain. Useful for cyclic transfers.
+ */
+ d->txd.callback = desc->txd.callback;
+ d->txd.callback_param = desc->txd.callback_param;
+
+ list_move_tail(&d->node, &edmac->active);
+ }
+}
+
+/* Called with @edmac->lock held and interrupts disabled */
+static struct ep93xx_dma_desc *
+ep93xx_dma_get_active(struct ep93xx_dma_chan *edmac)
+{
+ return list_first_entry(&edmac->active, struct ep93xx_dma_desc, node);
+}
+
+/**
+ * ep93xx_dma_advance_active - advances to the next active descriptor
+ * @edmac: channel
+ *
+ * Function advances active descriptor to the next in the @edmac->active and
+ * returns %true if we still have descriptors in the chain to process.
+ * Otherwise returns %false.
+ *
+ * When the channel is in cyclic mode always returns %true.
+ *
+ * Called with @edmac->lock held and interrupts disabled.
+ */
+static bool ep93xx_dma_advance_active(struct ep93xx_dma_chan *edmac)
+{
+ list_rotate_left(&edmac->active);
+
+ if (test_bit(EP93XX_DMA_IS_CYCLIC, &edmac->flags))
+ return true;
+
+ /*
+ * If txd.cookie is set it means that we are back in the first
+ * descriptor in the chain and hence done with it.
+ */
+ return !ep93xx_dma_get_active(edmac)->txd.cookie;
+}
+
+/*
+ * M2P DMA implementation
+ */
+
+static void m2p_set_control(struct ep93xx_dma_chan *edmac, u32 control)
+{
+ writel(control, edmac->regs + M2P_CONTROL);
+ /*
+ * EP93xx User's Guide states that we must perform a dummy read after
+ * write to the control register.
+ */
+ readl(edmac->regs + M2P_CONTROL);
+}
+
+static int m2p_hw_setup(struct ep93xx_dma_chan *edmac)
+{
+ struct ep93xx_dma_data *data = edmac->chan.private;
+ u32 control;
+
+ writel(data->port & 0xf, edmac->regs + M2P_PPALLOC);
+
+ control = M2P_CONTROL_CH_ERROR_INT | M2P_CONTROL_ICE
+ | M2P_CONTROL_ENABLE;
+ m2p_set_control(edmac, control);
+
+ return 0;
+}
+
+static inline u32 m2p_channel_state(struct ep93xx_dma_chan *edmac)
+{
+ return (readl(edmac->regs + M2P_STATUS) >> 4) & 0x3;
+}
+
+static void m2p_hw_shutdown(struct ep93xx_dma_chan *edmac)
+{
+ u32 control;
+
+ control = readl(edmac->regs + M2P_CONTROL);
+ control &= ~(M2P_CONTROL_STALLINT | M2P_CONTROL_NFBINT);
+ m2p_set_control(edmac, control);
+
+ while (m2p_channel_state(edmac) >= M2P_STATE_ON)
+ cpu_relax();
+
+ m2p_set_control(edmac, 0);
+
+ while (m2p_channel_state(edmac) == M2P_STATE_STALL)
+ cpu_relax();
+}
+
+static void m2p_fill_desc(struct ep93xx_dma_chan *edmac)
+{
+ struct ep93xx_dma_desc *desc = ep93xx_dma_get_active(edmac);
+ u32 bus_addr;
+
+ if (ep93xx_dma_chan_direction(&edmac->chan) == DMA_TO_DEVICE)
+ bus_addr = desc->src_addr;
+ else
+ bus_addr = desc->dst_addr;
+
+ if (edmac->buffer == 0) {
+ writel(desc->size, edmac->regs + M2P_MAXCNT0);
+ writel(bus_addr, edmac->regs + M2P_BASE0);
+ } else {
+ writel(desc->size, edmac->regs + M2P_MAXCNT1);
+ writel(bus_addr, edmac->regs + M2P_BASE1);
+ }
+
+ edmac->buffer ^= 1;
+}
+
+static void m2p_hw_submit(struct ep93xx_dma_chan *edmac)
+{
+ u32 control = readl(edmac->regs + M2P_CONTROL);
+
+ m2p_fill_desc(edmac);
+ control |= M2P_CONTROL_STALLINT;
+
+ if (ep93xx_dma_advance_active(edmac)) {
+ m2p_fill_desc(edmac);
+ control |= M2P_CONTROL_NFBINT;
+ }
+
+ m2p_set_control(edmac, control);
+}
+
+static int m2p_hw_interrupt(struct ep93xx_dma_chan *edmac)
+{
+ u32 irq_status = readl(edmac->regs + M2P_INTERRUPT);
+ u32 control;
+
+ if (irq_status & M2P_INTERRUPT_ERROR) {
+ struct ep93xx_dma_desc *desc = ep93xx_dma_get_active(edmac);
+
+ /* Clear the error interrupt */
+ writel(1, edmac->regs + M2P_INTERRUPT);
+
+ /*
+ * It seems that there is no easy way of reporting errors back
+ * to client so we just report the error here and continue as
+ * usual.
+ *
+ * Revisit this when there is a mechanism to report back the
+ * errors.
+ */
+ dev_err(chan2dev(edmac),
+ "DMA transfer failed! Details:\n"
+ "\tcookie : %d\n"
+ "\tsrc_addr : 0x%08x\n"
+ "\tdst_addr : 0x%08x\n"
+ "\tsize : %zu\n",
+ desc->txd.cookie, desc->src_addr, desc->dst_addr,
+ desc->size);
+ }
+
+ switch (irq_status & (M2P_INTERRUPT_STALL | M2P_INTERRUPT_NFB)) {
+ case M2P_INTERRUPT_STALL:
+ /* Disable interrupts */
+ control = readl(edmac->regs + M2P_CONTROL);
+ control &= ~(M2P_CONTROL_STALLINT | M2P_CONTROL_NFBINT);
+ m2p_set_control(edmac, control);
+
+ return INTERRUPT_DONE;
+
+ case M2P_INTERRUPT_NFB:
+ if (ep93xx_dma_advance_active(edmac))
+ m2p_fill_desc(edmac);
+
+ return INTERRUPT_NEXT_BUFFER;
+ }
+
+ return INTERRUPT_UNKNOWN;
+}
+
+/*
+ * M2M DMA implementation
+ *
+ * For the M2M transfers we don't use NFB at all. This is because it simply
+ * doesn't work well with memcpy transfers. When you submit both buffers it is
+ * extremely unlikely that you get an NFB interrupt, but it instead reports
+ * DONE interrupt and both buffers are already transferred which means that we
+ * weren't able to update the next buffer.
+ *
+ * So for now we "simulate" NFB by just submitting buffer after buffer
+ * without double buffering.
+ */
+
+static int m2m_hw_setup(struct ep93xx_dma_chan *edmac)
+{
+ const struct ep93xx_dma_data *data = edmac->chan.private;
+ u32 control = 0;
+
+ if (!data) {
+ /* This is memcpy channel, nothing to configure */
+ writel(control, edmac->regs + M2M_CONTROL);
+ return 0;
+ }
+
+ switch (data->port) {
+ case EP93XX_DMA_SSP:
+ /*
+ * This was found via experimenting - anything less than 5
+ * causes the channel to perform only a partial transfer which
+ * leads to problems since we don't get DONE interrupt then.
+ */
+ control = (5 << M2M_CONTROL_PWSC_SHIFT);
+ control |= M2M_CONTROL_NO_HDSK;
+
+ if (data->direction == DMA_TO_DEVICE) {
+ control |= M2M_CONTROL_DAH;
+ control |= M2M_CONTROL_TM_TX;
+ control |= M2M_CONTROL_RSS_SSPTX;
+ } else {
+ control |= M2M_CONTROL_SAH;
+ control |= M2M_CONTROL_TM_RX;
+ control |= M2M_CONTROL_RSS_SSPRX;
+ }
+ break;
+
+ case EP93XX_DMA_IDE:
+ /*
+ * This IDE part is totally untested. Values below are taken
+ * from the EP93xx Users's Guide and might not be correct.
+ */
+ control |= M2M_CONTROL_NO_HDSK;
+ control |= M2M_CONTROL_RSS_IDE;
+ control |= M2M_CONTROL_PW_16;
+
+ if (data->direction == DMA_TO_DEVICE) {
+ /* Worst case from the UG */
+ control = (3 << M2M_CONTROL_PWSC_SHIFT);
+ control |= M2M_CONTROL_DAH;
+ control |= M2M_CONTROL_TM_TX;
+ } else {
+ control = (2 << M2M_CONTROL_PWSC_SHIFT);
+ control |= M2M_CONTROL_SAH;
+ control |= M2M_CONTROL_TM_RX;
+ }
+ break;
+
+ default:
+ return -EINVAL;
+ }
+
+ writel(control, edmac->regs + M2M_CONTROL);
+ return 0;
+}
+
+static void m2m_hw_shutdown(struct ep93xx_dma_chan *edmac)
+{
+ /* Just disable the channel */
+ writel(0, edmac->regs + M2M_CONTROL);
+}
+
+static void m2m_fill_desc(struct ep93xx_dma_chan *edmac)
+{
+ struct ep93xx_dma_desc *desc = ep93xx_dma_get_active(edmac);
+
+ if (edmac->buffer == 0) {
+ writel(desc->src_addr, edmac->regs + M2M_SAR_BASE0);
+ writel(desc->dst_addr, edmac->regs + M2M_DAR_BASE0);
+ writel(desc->size, edmac->regs + M2M_BCR0);
+ } else {
+ writel(desc->src_addr, edmac->regs + M2M_SAR_BASE1);
+ writel(desc->dst_addr, edmac->regs + M2M_DAR_BASE1);
+ writel(desc->size, edmac->regs + M2M_BCR1);
+ }
+
+ edmac->buffer ^= 1;
+}
+
+static void m2m_hw_submit(struct ep93xx_dma_chan *edmac)
+{
+ struct ep93xx_dma_data *data = edmac->chan.private;
+ u32 control = readl(edmac->regs + M2M_CONTROL);
+
+ /*
+ * Since we allow clients to configure PW (peripheral width) we always
+ * clear PW bits here and then set them according what is given in
+ * the runtime configuration.
+ */
+ control &= ~M2M_CONTROL_PW_MASK;
+ control |= edmac->runtime_ctrl;
+
+ m2m_fill_desc(edmac);
+ control |= M2M_CONTROL_DONEINT;
+
+ /*
+ * Now we can finally enable the channel. For M2M channel this must be
+ * done _after_ the BCRx registers are programmed.
+ */
+ control |= M2M_CONTROL_ENABLE;
+ writel(control, edmac->regs + M2M_CONTROL);
+
+ if (!data) {
+ /*
+ * For memcpy channels the software trigger must be asserted
+ * in order to start the memcpy operation.
+ */
+ control |= M2M_CONTROL_START;
+ writel(control, edmac->regs + M2M_CONTROL);
+ }
+}
+
+static int m2m_hw_interrupt(struct ep93xx_dma_chan *edmac)
+{
+ u32 control;
+
+ if (!(readl(edmac->regs + M2M_INTERRUPT) & M2M_INTERRUPT_DONEINT))
+ return INTERRUPT_UNKNOWN;
+
+ /* Clear the DONE bit */
+ writel(0, edmac->regs + M2M_INTERRUPT);
+
+ /* Disable interrupts and the channel */
+ control = readl(edmac->regs + M2M_CONTROL);
+ control &= ~(M2M_CONTROL_DONEINT | M2M_CONTROL_ENABLE);
+ writel(control, edmac->regs + M2M_CONTROL);
+
+ /*
+ * Since we only get DONE interrupt we have to find out ourselves
+ * whether there still is something to process. So we try to advance
+ * the chain an see whether it succeeds.
+ */
+ if (ep93xx_dma_advance_active(edmac)) {
+ edmac->edma->hw_submit(edmac);
+ return INTERRUPT_NEXT_BUFFER;
+ }
+
+ return INTERRUPT_DONE;
+}
+
+/*
+ * DMA engine API implementation
+ */
+
+static struct ep93xx_dma_desc *
+ep93xx_dma_desc_get(struct ep93xx_dma_chan *edmac)
+{
+ struct ep93xx_dma_desc *desc, *_desc;
+ struct ep93xx_dma_desc *ret = NULL;
+ unsigned long flags;
+
+ spin_lock_irqsave(&edmac->lock, flags);
+ list_for_each_entry_safe(desc, _desc, &edmac->free_list, node) {
+ if (async_tx_test_ack(&desc->txd)) {
+ list_del_init(&desc->node);
+
+ /* Re-initialize the descriptor */
+ desc->src_addr = 0;
+ desc->dst_addr = 0;
+ desc->size = 0;
+ desc->complete = false;
+ desc->txd.cookie = 0;
+ desc->txd.callback = NULL;
+ desc->txd.callback_param = NULL;
+
+ ret = desc;
+ break;
+ }
+ }
+ spin_unlock_irqrestore(&edmac->lock, flags);
+ return ret;
+}
+
+static void ep93xx_dma_desc_put(struct ep93xx_dma_chan *edmac,
+ struct ep93xx_dma_desc *desc)
+{
+ if (desc) {
+ unsigned long flags;
+
+ spin_lock_irqsave(&edmac->lock, flags);
+ list_splice_init(&desc->tx_list, &edmac->free_list);
+ list_add(&desc->node, &edmac->free_list);
+ spin_unlock_irqrestore(&edmac->lock, flags);
+ }
+}
+
+/**
+ * ep93xx_dma_advance_work - start processing the next pending transaction
+ * @edmac: channel
+ *
+ * If we have pending transactions queued and we are currently idling, this
+ * function takes the next queued transaction from the @edmac->queue and
+ * pushes it to the hardware for execution.
+ */
+static void ep93xx_dma_advance_work(struct ep93xx_dma_chan *edmac)
+{
+ struct ep93xx_dma_desc *new;
+ unsigned long flags;
+
+ spin_lock_irqsave(&edmac->lock, flags);
+ if (!list_empty(&edmac->active) || list_empty(&edmac->queue)) {
+ spin_unlock_irqrestore(&edmac->lock, flags);
+ return;
+ }
+
+ /* Take the next descriptor from the pending queue */
+ new = list_first_entry(&edmac->queue, struct ep93xx_dma_desc, node);
+ list_del_init(&new->node);
+
+ ep93xx_dma_set_active(edmac, new);
+
+ /* Push it to the hardware */
+ edmac->edma->hw_submit(edmac);
+ spin_unlock_irqrestore(&edmac->lock, flags);
+}
+
+static void ep93xx_dma_unmap_buffers(struct ep93xx_dma_desc *desc)
+{
+ struct device *dev = desc->txd.chan->device->dev;
+
+ if (!(desc->txd.flags & DMA_COMPL_SKIP_SRC_UNMAP)) {
+ if (desc->txd.flags & DMA_COMPL_SRC_UNMAP_SINGLE)
+ dma_unmap_single(dev, desc->src_addr, desc->size,
+ DMA_TO_DEVICE);
+ else
+ dma_unmap_page(dev, desc->src_addr, desc->size,
+ DMA_TO_DEVICE);
+ }
+ if (!(desc->txd.flags & DMA_COMPL_SKIP_DEST_UNMAP)) {
+ if (desc->txd.flags & DMA_COMPL_DEST_UNMAP_SINGLE)
+ dma_unmap_single(dev, desc->dst_addr, desc->size,
+ DMA_FROM_DEVICE);
+ else
+ dma_unmap_page(dev, desc->dst_addr, desc->size,
+ DMA_FROM_DEVICE);
+ }
+}
+
+static void ep93xx_dma_tasklet(unsigned long data)
+{
+ struct ep93xx_dma_chan *edmac = (struct ep93xx_dma_chan *)data;
+ struct ep93xx_dma_desc *desc, *d;
+ dma_async_tx_callback callback;
+ void *callback_param;
+ LIST_HEAD(list);
+
+ spin_lock_irq(&edmac->lock);
+ desc = ep93xx_dma_get_active(edmac);
+ if (desc->complete) {
+ edmac->last_completed = desc->txd.cookie;
+ list_splice_init(&edmac->active, &list);
+ }
+ spin_unlock_irq(&edmac->lock);
+
+ /* Pick up the next descriptor from the queue */
+ ep93xx_dma_advance_work(edmac);
+
+ callback = desc->txd.callback;
+ callback_param = desc->txd.callback_param;
+
+ /* Now we can release all the chained descriptors */
+ list_for_each_entry_safe(desc, d, &list, node) {
+ /*
+ * For the memcpy channels the API requires us to unmap the
+ * buffers unless requested otherwise.
+ */
+ if (!edmac->chan.private)
+ ep93xx_dma_unmap_buffers(desc);
+
+ ep93xx_dma_desc_put(edmac, desc);
+ }
+
+ if (callback)
+ callback(callback_param);
+}
+
+static irqreturn_t ep93xx_dma_interrupt(int irq, void *dev_id)
+{
+ struct ep93xx_dma_chan *edmac = dev_id;
+ irqreturn_t ret = IRQ_HANDLED;
+
+ spin_lock(&edmac->lock);
+
+ switch (edmac->edma->hw_interrupt(edmac)) {
+ case INTERRUPT_DONE:
+ ep93xx_dma_get_active(edmac)->complete = true;
+ tasklet_schedule(&edmac->tasklet);
+ break;
+
+ case INTERRUPT_NEXT_BUFFER:
+ if (test_bit(EP93XX_DMA_IS_CYCLIC, &edmac->flags))
+ tasklet_schedule(&edmac->tasklet);
+ break;
+
+ default:
+ dev_warn(chan2dev(edmac), "unknown interrupt!\n");
+ ret = IRQ_NONE;
+ break;
+ }
+
+ spin_unlock(&edmac->lock);
+ return ret;
+}
+
+/**
+ * ep93xx_dma_tx_submit - set the prepared descriptor(s) to be executed
+ * @tx: descriptor to be executed
+ *
+ * Function will execute given descriptor on the hardware or if the hardware
+ * is busy, queue the descriptor to be executed later on. Returns cookie which
+ * can be used to poll the status of the descriptor.
+ */
+static dma_cookie_t ep93xx_dma_tx_submit(struct dma_async_tx_descriptor *tx)
+{
+ struct ep93xx_dma_chan *edmac = to_ep93xx_dma_chan(tx->chan);
+ struct ep93xx_dma_desc *desc;
+ dma_cookie_t cookie;
+ unsigned long flags;
+
+ spin_lock_irqsave(&edmac->lock, flags);
+
+ cookie = edmac->chan.cookie;
+
+ if (++cookie < 0)
+ cookie = 1;
+
+ desc = container_of(tx, struct ep93xx_dma_desc, txd);
+
+ edmac->chan.cookie = cookie;
+ desc->txd.cookie = cookie;
+
+ /*
+ * If nothing is currently prosessed, we push this descriptor
+ * directly to the hardware. Otherwise we put the descriptor
+ * to the pending queue.
+ */
+ if (list_empty(&edmac->active)) {
+ ep93xx_dma_set_active(edmac, desc);
+ edmac->edma->hw_submit(edmac);
+ } else {
+ list_add_tail(&desc->node, &edmac->queue);
+ }
+
+ spin_unlock_irqrestore(&edmac->lock, flags);
+ return cookie;
+}
+
+/**
+ * ep93xx_dma_alloc_chan_resources - allocate resources for the channel
+ * @chan: channel to allocate resources
+ *
+ * Function allocates necessary resources for the given DMA channel and
+ * returns number of allocated descriptors for the channel. Negative errno
+ * is returned in case of failure.
+ */
+static int ep93xx_dma_alloc_chan_resources(struct dma_chan *chan)
+{
+ struct ep93xx_dma_chan *edmac = to_ep93xx_dma_chan(chan);
+ struct ep93xx_dma_data *data = chan->private;
+ const char *name = dma_chan_name(chan);
+ int ret, i;
+
+ /* Sanity check the channel parameters */
+ if (!edmac->edma->m2m) {
+ if (!data)
+ return -EINVAL;
+ if (data->port < EP93XX_DMA_I2S1 ||
+ data->port > EP93XX_DMA_IRDA)
+ return -EINVAL;
+ if (data->direction != ep93xx_dma_chan_direction(chan))
+ return -EINVAL;
+ } else {
+ if (data) {
+ switch (data->port) {
+ case EP93XX_DMA_SSP:
+ case EP93XX_DMA_IDE:
+ if (data->direction != DMA_TO_DEVICE &&
+ data->direction != DMA_FROM_DEVICE)
+ return -EINVAL;
+ break;
+ default:
+ return -EINVAL;
+ }
+ }
+ }
+
+ if (data && data->name)
+ name = data->name;
+
+ ret = clk_enable(edmac->clk);
+ if (ret)
+ return ret;
+
+ ret = request_irq(edmac->irq, ep93xx_dma_interrupt, 0, name, edmac);
+ if (ret)
+ goto fail_clk_disable;
+
+ spin_lock_irq(&edmac->lock);
+ edmac->last_completed = 1;
+ edmac->chan.cookie = 1;
+ ret = edmac->edma->hw_setup(edmac);
+ spin_unlock_irq(&edmac->lock);
+
+ if (ret)
+ goto fail_free_irq;
+
+ for (i = 0; i < DMA_MAX_CHAN_DESCRIPTORS; i++) {
+ struct ep93xx_dma_desc *desc;
+
+ desc = kzalloc(sizeof(*desc), GFP_KERNEL);
+ if (!desc) {
+ dev_warn(chan2dev(edmac), "not enough descriptors\n");
+ break;
+ }
+
+ INIT_LIST_HEAD(&desc->tx_list);
+
+ dma_async_tx_descriptor_init(&desc->txd, chan);
+ desc->txd.flags = DMA_CTRL_ACK;
+ desc->txd.tx_submit = ep93xx_dma_tx_submit;
+
+ ep93xx_dma_desc_put(edmac, desc);
+ }
+
+ return i;
+
+fail_free_irq:
+ free_irq(edmac->irq, edmac);
+fail_clk_disable:
+ clk_disable(edmac->clk);
+
+ return ret;
+}
+
+/**
+ * ep93xx_dma_free_chan_resources - release resources for the channel
+ * @chan: channel
+ *
+ * Function releases all the resources allocated for the given channel.
+ * The channel must be idle when this is called.
+ */
+static void ep93xx_dma_free_chan_resources(struct dma_chan *chan)
+{
+ struct ep93xx_dma_chan *edmac = to_ep93xx_dma_chan(chan);
+ struct ep93xx_dma_desc *desc, *d;
+ unsigned long flags;
+ LIST_HEAD(list);
+
+ BUG_ON(!list_empty(&edmac->active));
+ BUG_ON(!list_empty(&edmac->queue));
+
+ spin_lock_irqsave(&edmac->lock, flags);
+ edmac->edma->hw_shutdown(edmac);
+ edmac->runtime_addr = 0;
+ edmac->runtime_ctrl = 0;
+ edmac->buffer = 0;
+ list_splice_init(&edmac->free_list, &list);
+ spin_unlock_irqrestore(&edmac->lock, flags);
+
+ list_for_each_entry_safe(desc, d, &list, node)
+ kfree(desc);
+
+ clk_disable(edmac->clk);
+ free_irq(edmac->irq, edmac);
+}
+
+/**
+ * ep93xx_dma_prep_dma_memcpy - prepare a memcpy DMA operation
+ * @chan: channel
+ * @dest: destination bus address
+ * @src: source bus address
+ * @len: size of the transaction
+ * @flags: flags for the descriptor
+ *
+ * Returns a valid DMA descriptor or %NULL in case of failure.
+ */
+static struct dma_async_tx_descriptor *
+ep93xx_dma_prep_dma_memcpy(struct dma_chan *chan, dma_addr_t dest,
+ dma_addr_t src, size_t len, unsigned long flags)
+{
+ struct ep93xx_dma_chan *edmac = to_ep93xx_dma_chan(chan);
+ struct ep93xx_dma_desc *desc, *first;
+ size_t bytes, offset;
+
+ first = NULL;
+ for (offset = 0; offset < len; offset += bytes) {
+ desc = ep93xx_dma_desc_get(edmac);
+ if (!desc) {
+ dev_warn(chan2dev(edmac), "couln't get descriptor\n");
+ goto fail;
+ }
+
+ bytes = min_t(size_t, len - offset, DMA_MAX_CHAN_BYTES);
+
+ desc->src_addr = src + offset;
+ desc->dst_addr = dest + offset;
+ desc->size = bytes;
+
+ if (!first)
+ first = desc;
+ else
+ list_add_tail(&desc->node, &first->tx_list);
+ }
+
+ first->txd.cookie = -EBUSY;
+ first->txd.flags = flags;
+
+ return &first->txd;
+fail:
+ ep93xx_dma_desc_put(edmac, first);
+ return NULL;
+}
+
+/**
+ * ep93xx_dma_prep_slave_sg - prepare a slave DMA operation
+ * @chan: channel
+ * @sgl: list of buffers to transfer
+ * @sg_len: number of entries in @sgl
+ * @dir: direction of tha DMA transfer
+ * @flags: flags for the descriptor
+ *
+ * Returns a valid DMA descriptor or %NULL in case of failure.
+ */
+static struct dma_async_tx_descriptor *
+ep93xx_dma_prep_slave_sg(struct dma_chan *chan, struct scatterlist *sgl,
+ unsigned int sg_len, enum dma_data_direction dir,
+ unsigned long flags)
+{
+ struct ep93xx_dma_chan *edmac = to_ep93xx_dma_chan(chan);
+ struct ep93xx_dma_desc *desc, *first;
+ struct scatterlist *sg;
+ int i;
+
+ if (!edmac->edma->m2m && dir != ep93xx_dma_chan_direction(chan)) {
+ dev_warn(chan2dev(edmac),
+ "channel was configured with different direction\n");
+ return NULL;
+ }
+
+ if (test_bit(EP93XX_DMA_IS_CYCLIC, &edmac->flags)) {
+ dev_warn(chan2dev(edmac),
+ "channel is already used for cyclic transfers\n");
+ return NULL;
+ }
+
+ first = NULL;
+ for_each_sg(sgl, sg, sg_len, i) {
+ size_t sg_len = sg_dma_len(sg);
+
+ if (sg_len > DMA_MAX_CHAN_BYTES) {
+ dev_warn(chan2dev(edmac), "too big transfer size %d\n",
+ sg_len);
+ goto fail;
+ }
+
+ desc = ep93xx_dma_desc_get(edmac);
+ if (!desc) {
+ dev_warn(chan2dev(edmac), "couln't get descriptor\n");
+ goto fail;
+ }
+
+ if (dir == DMA_TO_DEVICE) {
+ desc->src_addr = sg_dma_address(sg);
+ desc->dst_addr = edmac->runtime_addr;
+ } else {
+ desc->src_addr = edmac->runtime_addr;
+ desc->dst_addr = sg_dma_address(sg);
+ }
+ desc->size = sg_len;
+
+ if (!first)
+ first = desc;
+ else
+ list_add_tail(&desc->node, &first->tx_list);
+ }
+
+ first->txd.cookie = -EBUSY;
+ first->txd.flags = flags;
+
+ return &first->txd;
+
+fail:
+ ep93xx_dma_desc_put(edmac, first);
+ return NULL;
+}
+
+/**
+ * ep93xx_dma_prep_dma_cyclic - prepare a cyclic DMA operation
+ * @chan: channel
+ * @dma_addr: DMA mapped address of the buffer
+ * @buf_len: length of the buffer (in bytes)
+ * @period_len: lenght of a single period
+ * @dir: direction of the operation
+ *
+ * Prepares a descriptor for cyclic DMA operation. This means that once the
+ * descriptor is submitted, we will be submitting in a @period_len sized
+ * buffers and calling callback once the period has been elapsed. Transfer
+ * terminates only when client calls dmaengine_terminate_all() for this
+ * channel.
+ *
+ * Returns a valid DMA descriptor or %NULL in case of failure.
+ */
+static struct dma_async_tx_descriptor *
+ep93xx_dma_prep_dma_cyclic(struct dma_chan *chan, dma_addr_t dma_addr,
+ size_t buf_len, size_t period_len,
+ enum dma_data_direction dir)
+{
+ struct ep93xx_dma_chan *edmac = to_ep93xx_dma_chan(chan);
+ struct ep93xx_dma_desc *desc, *first;
+ size_t offset = 0;
+
+ if (!edmac->edma->m2m && dir != ep93xx_dma_chan_direction(chan)) {
+ dev_warn(chan2dev(edmac),
+ "channel was configured with different direction\n");
+ return NULL;
+ }
+
+ if (test_and_set_bit(EP93XX_DMA_IS_CYCLIC, &edmac->flags)) {
+ dev_warn(chan2dev(edmac),
+ "channel is already used for cyclic transfers\n");
+ return NULL;
+ }
+
+ if (period_len > DMA_MAX_CHAN_BYTES) {
+ dev_warn(chan2dev(edmac), "too big period length %d\n",
+ period_len);
+ return NULL;
+ }
+
+ /* Split the buffer into period size chunks */
+ first = NULL;
+ for (offset = 0; offset < buf_len; offset += period_len) {
+ desc = ep93xx_dma_desc_get(edmac);
+ if (!desc) {
+ dev_warn(chan2dev(edmac), "couln't get descriptor\n");
+ goto fail;
+ }
+
+ if (dir == DMA_TO_DEVICE) {
+ desc->src_addr = dma_addr + offset;
+ desc->dst_addr = edmac->runtime_addr;
+ } else {
+ desc->src_addr = edmac->runtime_addr;
+ desc->dst_addr = dma_addr + offset;
+ }
+
+ desc->size = period_len;
+
+ if (!first)
+ first = desc;
+ else
+ list_add_tail(&desc->node, &first->tx_list);
+ }
+
+ first->txd.cookie = -EBUSY;
+
+ return &first->txd;
+
+fail:
+ ep93xx_dma_desc_put(edmac, first);
+ return NULL;
+}
+
+/**
+ * ep93xx_dma_terminate_all - terminate all transactions
+ * @edmac: channel
+ *
+ * Stops all DMA transactions. All descriptors are put back to the
+ * @edmac->free_list and callbacks are _not_ called.
+ */
+static int ep93xx_dma_terminate_all(struct ep93xx_dma_chan *edmac)
+{
+ struct ep93xx_dma_desc *desc, *_d;
+ unsigned long flags;
+ LIST_HEAD(list);
+
+ spin_lock_irqsave(&edmac->lock, flags);
+ /* First we disable and flush the DMA channel */
+ edmac->edma->hw_shutdown(edmac);
+ clear_bit(EP93XX_DMA_IS_CYCLIC, &edmac->flags);
+ list_splice_init(&edmac->active, &list);
+ list_splice_init(&edmac->queue, &list);
+ /*
+ * We then re-enable the channel. This way we can continue submitting
+ * the descriptors by just calling ->hw_submit() again.
+ */
+ edmac->edma->hw_setup(edmac);
+ spin_unlock_irqrestore(&edmac->lock, flags);
+
+ list_for_each_entry_safe(desc, _d, &list, node)
+ ep93xx_dma_desc_put(edmac, desc);
+
+ return 0;
+}
+
+static int ep93xx_dma_slave_config(struct ep93xx_dma_chan *edmac,
+ struct dma_slave_config *config)
+{
+ enum dma_slave_buswidth width;
+ unsigned long flags;
+ u32 addr, ctrl;
+
+ if (!edmac->edma->m2m)
+ return -EINVAL;
+
+ switch (config->direction) {
+ case DMA_FROM_DEVICE:
+ width = config->src_addr_width;
+ addr = config->src_addr;
+ break;
+
+ case DMA_TO_DEVICE:
+ width = config->dst_addr_width;
+ addr = config->dst_addr;
+ break;
+
+ default:
+ return -EINVAL;
+ }
+
+ switch (width) {
+ case DMA_SLAVE_BUSWIDTH_1_BYTE:
+ ctrl = 0;
+ break;
+ case DMA_SLAVE_BUSWIDTH_2_BYTES:
+ ctrl = M2M_CONTROL_PW_16;
+ break;
+ case DMA_SLAVE_BUSWIDTH_4_BYTES:
+ ctrl = M2M_CONTROL_PW_32;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ spin_lock_irqsave(&edmac->lock, flags);
+ edmac->runtime_addr = addr;
+ edmac->runtime_ctrl = ctrl;
+ spin_unlock_irqrestore(&edmac->lock, flags);
+
+ return 0;
+}
+
+/**
+ * ep93xx_dma_control - manipulate all pending operations on a channel
+ * @chan: channel
+ * @cmd: control command to perform
+ * @arg: optional argument
+ *
+ * Controls the channel. Function returns %0 in case of success or negative
+ * error in case of failure.
+ */
+static int ep93xx_dma_control(struct dma_chan *chan, enum dma_ctrl_cmd cmd,
+ unsigned long arg)
+{
+ struct ep93xx_dma_chan *edmac = to_ep93xx_dma_chan(chan);
+ struct dma_slave_config *config;
+
+ switch (cmd) {
+ case DMA_TERMINATE_ALL:
+ return ep93xx_dma_terminate_all(edmac);
+
+ case DMA_SLAVE_CONFIG:
+ config = (struct dma_slave_config *)arg;
+ return ep93xx_dma_slave_config(edmac, config);
+
+ default:
+ break;
+ }
+
+ return -ENOSYS;
+}
+
+/**
+ * ep93xx_dma_tx_status - check if a transaction is completed
+ * @chan: channel
+ * @cookie: transaction specific cookie
+ * @state: state of the transaction is stored here if given
+ *
+ * This function can be used to query state of a given transaction.
+ */
+static enum dma_status ep93xx_dma_tx_status(struct dma_chan *chan,
+ dma_cookie_t cookie,
+ struct dma_tx_state *state)
+{
+ struct ep93xx_dma_chan *edmac = to_ep93xx_dma_chan(chan);
+ dma_cookie_t last_used, last_completed;
+ enum dma_status ret;
+ unsigned long flags;
+
+ spin_lock_irqsave(&edmac->lock, flags);
+ last_used = chan->cookie;
+ last_completed = edmac->last_completed;
+ spin_unlock_irqrestore(&edmac->lock, flags);
+
+ ret = dma_async_is_complete(cookie, last_completed, last_used);
+ dma_set_tx_state(state, last_completed, last_used, 0);
+
+ return ret;
+}
+
+/**
+ * ep93xx_dma_issue_pending - push pending transactions to the hardware
+ * @chan: channel
+ *
+ * When this function is called, all pending transactions are pushed to the
+ * hardware and executed.
+ */
+static void ep93xx_dma_issue_pending(struct dma_chan *chan)
+{
+ ep93xx_dma_advance_work(to_ep93xx_dma_chan(chan));
+}
+
+static int __init ep93xx_dma_probe(struct platform_device *pdev)
+{
+ struct ep93xx_dma_platform_data *pdata = dev_get_platdata(&pdev->dev);
+ struct ep93xx_dma_engine *edma;
+ struct dma_device *dma_dev;
+ size_t edma_size;
+ int ret, i;
+
+ edma_size = pdata->num_channels * sizeof(struct ep93xx_dma_chan);
+ edma = kzalloc(sizeof(*edma) + edma_size, GFP_KERNEL);
+ if (!edma)
+ return -ENOMEM;
+
+ dma_dev = &edma->dma_dev;
+ edma->m2m = platform_get_device_id(pdev)->driver_data;
+ edma->num_channels = pdata->num_channels;
+
+ INIT_LIST_HEAD(&dma_dev->channels);
+ for (i = 0; i < pdata->num_channels; i++) {
+ const struct ep93xx_dma_chan_data *cdata = &pdata->channels[i];
+ struct ep93xx_dma_chan *edmac = &edma->channels[i];
+
+ edmac->chan.device = dma_dev;
+ edmac->regs = cdata->base;
+ edmac->irq = cdata->irq;
+ edmac->edma = edma;
+
+ edmac->clk = clk_get(NULL, cdata->name);
+ if (IS_ERR(edmac->clk)) {
+ dev_warn(&pdev->dev, "failed to get clock for %s\n",
+ cdata->name);
+ continue;
+ }
+
+ spin_lock_init(&edmac->lock);
+ INIT_LIST_HEAD(&edmac->active);
+ INIT_LIST_HEAD(&edmac->queue);
+ INIT_LIST_HEAD(&edmac->free_list);
+ tasklet_init(&edmac->tasklet, ep93xx_dma_tasklet,
+ (unsigned long)edmac);
+
+ list_add_tail(&edmac->chan.device_node,
+ &dma_dev->channels);
+ }
+
+ dma_cap_zero(dma_dev->cap_mask);
+ dma_cap_set(DMA_SLAVE, dma_dev->cap_mask);
+ dma_cap_set(DMA_CYCLIC, dma_dev->cap_mask);
+
+ dma_dev->dev = &pdev->dev;
+ dma_dev->device_alloc_chan_resources = ep93xx_dma_alloc_chan_resources;
+ dma_dev->device_free_chan_resources = ep93xx_dma_free_chan_resources;
+ dma_dev->device_prep_slave_sg = ep93xx_dma_prep_slave_sg;
+ dma_dev->device_prep_dma_cyclic = ep93xx_dma_prep_dma_cyclic;
+ dma_dev->device_control = ep93xx_dma_control;
+ dma_dev->device_issue_pending = ep93xx_dma_issue_pending;
+ dma_dev->device_tx_status = ep93xx_dma_tx_status;
+
+ dma_set_max_seg_size(dma_dev->dev, DMA_MAX_CHAN_BYTES);
+
+ if (edma->m2m) {
+ dma_cap_set(DMA_MEMCPY, dma_dev->cap_mask);
+ dma_dev->device_prep_dma_memcpy = ep93xx_dma_prep_dma_memcpy;
+
+ edma->hw_setup = m2m_hw_setup;
+ edma->hw_shutdown = m2m_hw_shutdown;
+ edma->hw_submit = m2m_hw_submit;
+ edma->hw_interrupt = m2m_hw_interrupt;
+ } else {
+ dma_cap_set(DMA_PRIVATE, dma_dev->cap_mask);
+
+ edma->hw_setup = m2p_hw_setup;
+ edma->hw_shutdown = m2p_hw_shutdown;
+ edma->hw_submit = m2p_hw_submit;
+ edma->hw_interrupt = m2p_hw_interrupt;
+ }
+
+ ret = dma_async_device_register(dma_dev);
+ if (unlikely(ret)) {
+ for (i = 0; i < edma->num_channels; i++) {
+ struct ep93xx_dma_chan *edmac = &edma->channels[i];
+ if (!IS_ERR_OR_NULL(edmac->clk))
+ clk_put(edmac->clk);
+ }
+ kfree(edma);
+ } else {
+ dev_info(dma_dev->dev, "EP93xx M2%s DMA ready\n",
+ edma->m2m ? "M" : "P");
+ }
+
+ return ret;
+}
+
+static struct platform_device_id ep93xx_dma_driver_ids[] = {
+ { "ep93xx-dma-m2p", 0 },
+ { "ep93xx-dma-m2m", 1 },
+ { },
+};
+
+static struct platform_driver ep93xx_dma_driver = {
+ .driver = {
+ .name = "ep93xx-dma",
+ },
+ .id_table = ep93xx_dma_driver_ids,
+};
+
+static int __init ep93xx_dma_module_init(void)
+{
+ return platform_driver_probe(&ep93xx_dma_driver, ep93xx_dma_probe);
+}
+subsys_initcall(ep93xx_dma_module_init);
+
+MODULE_AUTHOR("Mika Westerberg <mika.westerberg@iki.fi>");
+MODULE_DESCRIPTION("EP93xx DMA driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/dma/imx-sdma.c b/drivers/dma/imx-sdma.c
index b6d1455..ec53980 100644
--- a/drivers/dma/imx-sdma.c
+++ b/drivers/dma/imx-sdma.c
@@ -1281,8 +1281,10 @@
goto err_request_irq;
sdma->script_addrs = kzalloc(sizeof(*sdma->script_addrs), GFP_KERNEL);
- if (!sdma->script_addrs)
+ if (!sdma->script_addrs) {
+ ret = -ENOMEM;
goto err_alloc;
+ }
sdma->version = pdata->sdma_version;
diff --git a/drivers/dma/intel_mid_dma.c b/drivers/dma/intel_mid_dma.c
index f653517..8a3fdd8 100644
--- a/drivers/dma/intel_mid_dma.c
+++ b/drivers/dma/intel_mid_dma.c
@@ -1351,7 +1351,6 @@
return -EAGAIN;
}
device->state = SUSPENDED;
- pci_set_drvdata(pci, device);
pci_save_state(pci);
pci_disable_device(pci);
pci_set_power_state(pci, PCI_D3hot);
@@ -1380,7 +1379,6 @@
}
device->state = RUNNING;
iowrite32(REG_BIT0, device->dma_base + DMA_CFG);
- pci_set_drvdata(pci, device);
return 0;
}
diff --git a/drivers/dma/ipu/ipu_idmac.c b/drivers/dma/ipu/ipu_idmac.c
index c1a125e7..25447a8 100644
--- a/drivers/dma/ipu/ipu_idmac.c
+++ b/drivers/dma/ipu/ipu_idmac.c
@@ -1705,16 +1705,14 @@
ipu_data.irq_fn, ipu_data.irq_err, ipu_data.irq_base);
/* Remap IPU common registers */
- ipu_data.reg_ipu = ioremap(mem_ipu->start,
- mem_ipu->end - mem_ipu->start + 1);
+ ipu_data.reg_ipu = ioremap(mem_ipu->start, resource_size(mem_ipu));
if (!ipu_data.reg_ipu) {
ret = -ENOMEM;
goto err_ioremap_ipu;
}
/* Remap Image Converter and Image DMA Controller registers */
- ipu_data.reg_ic = ioremap(mem_ic->start,
- mem_ic->end - mem_ic->start + 1);
+ ipu_data.reg_ic = ioremap(mem_ic->start, resource_size(mem_ic));
if (!ipu_data.reg_ic) {
ret = -ENOMEM;
goto err_ioremap_ic;
diff --git a/drivers/dma/mv_xor.c b/drivers/dma/mv_xor.c
index 954e334..9a353c2 100644
--- a/drivers/dma/mv_xor.c
+++ b/drivers/dma/mv_xor.c
@@ -1305,7 +1305,7 @@
return -ENODEV;
msp->xor_base = devm_ioremap(&pdev->dev, res->start,
- res->end - res->start + 1);
+ resource_size(res));
if (!msp->xor_base)
return -EBUSY;
@@ -1314,7 +1314,7 @@
return -ENODEV;
msp->xor_high_base = devm_ioremap(&pdev->dev, res->start,
- res->end - res->start + 1);
+ resource_size(res));
if (!msp->xor_high_base)
return -EBUSY;
diff --git a/drivers/dma/mxs-dma.c b/drivers/dma/mxs-dma.c
index 88aad4f..be641cb 100644
--- a/drivers/dma/mxs-dma.c
+++ b/drivers/dma/mxs-dma.c
@@ -327,10 +327,12 @@
memset(mxs_chan->ccw, 0, PAGE_SIZE);
- ret = request_irq(mxs_chan->chan_irq, mxs_dma_int_handler,
- 0, "mxs-dma", mxs_dma);
- if (ret)
- goto err_irq;
+ if (mxs_chan->chan_irq != NO_IRQ) {
+ ret = request_irq(mxs_chan->chan_irq, mxs_dma_int_handler,
+ 0, "mxs-dma", mxs_dma);
+ if (ret)
+ goto err_irq;
+ }
ret = clk_enable(mxs_dma->clk);
if (ret)
@@ -535,6 +537,7 @@
switch (cmd) {
case DMA_TERMINATE_ALL:
mxs_dma_disable_chan(mxs_chan);
+ mxs_dma_reset_chan(mxs_chan);
break;
case DMA_PAUSE:
mxs_dma_pause_chan(mxs_chan);
@@ -707,6 +710,8 @@
}, {
.name = "mxs-dma-apbx",
.driver_data = MXS_DMA_APBX,
+ }, {
+ /* end of list */
}
};
diff --git a/drivers/dma/pch_dma.c b/drivers/dma/pch_dma.c
index ff5b38f..1ac8d4b 100644
--- a/drivers/dma/pch_dma.c
+++ b/drivers/dma/pch_dma.c
@@ -45,7 +45,8 @@
#define DMA_STATUS_MASK_BITS 0x3
#define DMA_STATUS_SHIFT_BITS 16
#define DMA_STATUS_IRQ(x) (0x1 << (x))
-#define DMA_STATUS_ERR(x) (0x1 << ((x) + 8))
+#define DMA_STATUS0_ERR(x) (0x1 << ((x) + 8))
+#define DMA_STATUS2_ERR(x) (0x1 << (x))
#define DMA_DESC_WIDTH_SHIFT_BITS 12
#define DMA_DESC_WIDTH_1_BYTE (0x3 << DMA_DESC_WIDTH_SHIFT_BITS)
@@ -61,6 +62,9 @@
#define MAX_CHAN_NR 8
+#define DMA_MASK_CTL0_MODE 0x33333333
+#define DMA_MASK_CTL2_MODE 0x00003333
+
static unsigned int init_nr_desc_per_channel = 64;
module_param(init_nr_desc_per_channel, uint, 0644);
MODULE_PARM_DESC(init_nr_desc_per_channel,
@@ -133,6 +137,7 @@
#define PCH_DMA_CTL3 0x0C
#define PCH_DMA_STS0 0x10
#define PCH_DMA_STS1 0x14
+#define PCH_DMA_STS2 0x18
#define dma_readl(pd, name) \
readl((pd)->membase + PCH_DMA_##name)
@@ -183,13 +188,19 @@
{
struct pch_dma *pd = to_pd(chan->device);
u32 val;
+ int pos;
+
+ if (chan->chan_id < 8)
+ pos = chan->chan_id;
+ else
+ pos = chan->chan_id + 8;
val = dma_readl(pd, CTL2);
if (enable)
- val |= 0x1 << chan->chan_id;
+ val |= 0x1 << pos;
else
- val &= ~(0x1 << chan->chan_id);
+ val &= ~(0x1 << pos);
dma_writel(pd, CTL2, val);
@@ -202,10 +213,17 @@
struct pch_dma_chan *pd_chan = to_pd_chan(chan);
struct pch_dma *pd = to_pd(chan->device);
u32 val;
+ u32 mask_mode;
+ u32 mask_ctl;
if (chan->chan_id < 8) {
val = dma_readl(pd, CTL0);
+ mask_mode = DMA_CTL0_MODE_MASK_BITS <<
+ (DMA_CTL0_BITS_PER_CH * chan->chan_id);
+ mask_ctl = DMA_MASK_CTL0_MODE & ~(DMA_CTL0_MODE_MASK_BITS <<
+ (DMA_CTL0_BITS_PER_CH * chan->chan_id));
+ val &= mask_mode;
if (pd_chan->dir == DMA_TO_DEVICE)
val |= 0x1 << (DMA_CTL0_BITS_PER_CH * chan->chan_id +
DMA_CTL0_DIR_SHIFT_BITS);
@@ -213,18 +231,24 @@
val &= ~(0x1 << (DMA_CTL0_BITS_PER_CH * chan->chan_id +
DMA_CTL0_DIR_SHIFT_BITS));
+ val |= mask_ctl;
dma_writel(pd, CTL0, val);
} else {
int ch = chan->chan_id - 8; /* ch8-->0 ch9-->1 ... ch11->3 */
val = dma_readl(pd, CTL3);
+ mask_mode = DMA_CTL0_MODE_MASK_BITS <<
+ (DMA_CTL0_BITS_PER_CH * ch);
+ mask_ctl = DMA_MASK_CTL2_MODE & ~(DMA_CTL0_MODE_MASK_BITS <<
+ (DMA_CTL0_BITS_PER_CH * ch));
+ val &= mask_mode;
if (pd_chan->dir == DMA_TO_DEVICE)
val |= 0x1 << (DMA_CTL0_BITS_PER_CH * ch +
DMA_CTL0_DIR_SHIFT_BITS);
else
val &= ~(0x1 << (DMA_CTL0_BITS_PER_CH * ch +
DMA_CTL0_DIR_SHIFT_BITS));
-
+ val |= mask_ctl;
dma_writel(pd, CTL3, val);
}
@@ -236,33 +260,37 @@
{
struct pch_dma *pd = to_pd(chan->device);
u32 val;
+ u32 mask_ctl;
+ u32 mask_dir;
if (chan->chan_id < 8) {
+ mask_ctl = DMA_MASK_CTL0_MODE & ~(DMA_CTL0_MODE_MASK_BITS <<
+ (DMA_CTL0_BITS_PER_CH * chan->chan_id));
+ mask_dir = 1 << (DMA_CTL0_BITS_PER_CH * chan->chan_id +\
+ DMA_CTL0_DIR_SHIFT_BITS);
val = dma_readl(pd, CTL0);
-
- val &= ~(DMA_CTL0_MODE_MASK_BITS <<
- (DMA_CTL0_BITS_PER_CH * chan->chan_id));
+ val &= mask_dir;
val |= mode << (DMA_CTL0_BITS_PER_CH * chan->chan_id);
-
+ val |= mask_ctl;
dma_writel(pd, CTL0, val);
} else {
int ch = chan->chan_id - 8; /* ch8-->0 ch9-->1 ... ch11->3 */
-
+ mask_ctl = DMA_MASK_CTL2_MODE & ~(DMA_CTL0_MODE_MASK_BITS <<
+ (DMA_CTL0_BITS_PER_CH * ch));
+ mask_dir = 1 << (DMA_CTL0_BITS_PER_CH * ch +\
+ DMA_CTL0_DIR_SHIFT_BITS);
val = dma_readl(pd, CTL3);
-
- val &= ~(DMA_CTL0_MODE_MASK_BITS <<
- (DMA_CTL0_BITS_PER_CH * ch));
+ val &= mask_dir;
val |= mode << (DMA_CTL0_BITS_PER_CH * ch);
-
+ val |= mask_ctl;
dma_writel(pd, CTL3, val);
-
}
dev_dbg(chan2dev(chan), "pdc_set_mode: chan %d -> %x\n",
chan->chan_id, val);
}
-static u32 pdc_get_status(struct pch_dma_chan *pd_chan)
+static u32 pdc_get_status0(struct pch_dma_chan *pd_chan)
{
struct pch_dma *pd = to_pd(pd_chan->chan.device);
u32 val;
@@ -272,9 +300,27 @@
DMA_STATUS_BITS_PER_CH * pd_chan->chan.chan_id));
}
+static u32 pdc_get_status2(struct pch_dma_chan *pd_chan)
+{
+ struct pch_dma *pd = to_pd(pd_chan->chan.device);
+ u32 val;
+
+ val = dma_readl(pd, STS2);
+ return DMA_STATUS_MASK_BITS & (val >> (DMA_STATUS_SHIFT_BITS +
+ DMA_STATUS_BITS_PER_CH * (pd_chan->chan.chan_id - 8)));
+}
+
static bool pdc_is_idle(struct pch_dma_chan *pd_chan)
{
- if (pdc_get_status(pd_chan) == DMA_STATUS_IDLE)
+ u32 sts;
+
+ if (pd_chan->chan.chan_id < 8)
+ sts = pdc_get_status0(pd_chan);
+ else
+ sts = pdc_get_status2(pd_chan);
+
+
+ if (sts == DMA_STATUS_IDLE)
return true;
else
return false;
@@ -495,11 +541,11 @@
list_add_tail(&desc->desc_node, &tmp_list);
}
- spin_lock_bh(&pd_chan->lock);
+ spin_lock_irq(&pd_chan->lock);
list_splice(&tmp_list, &pd_chan->free_list);
pd_chan->descs_allocated = i;
pd_chan->completed_cookie = chan->cookie = 1;
- spin_unlock_bh(&pd_chan->lock);
+ spin_unlock_irq(&pd_chan->lock);
pdc_enable_irq(chan, 1);
@@ -517,10 +563,10 @@
BUG_ON(!list_empty(&pd_chan->active_list));
BUG_ON(!list_empty(&pd_chan->queue));
- spin_lock_bh(&pd_chan->lock);
+ spin_lock_irq(&pd_chan->lock);
list_splice_init(&pd_chan->free_list, &tmp_list);
pd_chan->descs_allocated = 0;
- spin_unlock_bh(&pd_chan->lock);
+ spin_unlock_irq(&pd_chan->lock);
list_for_each_entry_safe(desc, _d, &tmp_list, desc_node)
pci_pool_free(pd->pool, desc, desc->txd.phys);
@@ -536,10 +582,10 @@
dma_cookie_t last_completed;
int ret;
- spin_lock_bh(&pd_chan->lock);
+ spin_lock_irq(&pd_chan->lock);
last_completed = pd_chan->completed_cookie;
last_used = chan->cookie;
- spin_unlock_bh(&pd_chan->lock);
+ spin_unlock_irq(&pd_chan->lock);
ret = dma_async_is_complete(cookie, last_completed, last_used);
@@ -654,7 +700,7 @@
if (cmd != DMA_TERMINATE_ALL)
return -ENXIO;
- spin_lock_bh(&pd_chan->lock);
+ spin_lock_irq(&pd_chan->lock);
pdc_set_mode(&pd_chan->chan, DMA_CTL0_DISABLE);
@@ -664,7 +710,7 @@
list_for_each_entry_safe(desc, _d, &list, desc_node)
pdc_chain_complete(pd_chan, desc);
- spin_unlock_bh(&pd_chan->lock);
+ spin_unlock_irq(&pd_chan->lock);
return 0;
}
@@ -693,30 +739,45 @@
struct pch_dma *pd = (struct pch_dma *)devid;
struct pch_dma_chan *pd_chan;
u32 sts0;
+ u32 sts2;
int i;
- int ret = IRQ_NONE;
+ int ret0 = IRQ_NONE;
+ int ret2 = IRQ_NONE;
sts0 = dma_readl(pd, STS0);
+ sts2 = dma_readl(pd, STS2);
dev_dbg(pd->dma.dev, "pd_irq sts0: %x\n", sts0);
for (i = 0; i < pd->dma.chancnt; i++) {
pd_chan = &pd->channels[i];
- if (sts0 & DMA_STATUS_IRQ(i)) {
- if (sts0 & DMA_STATUS_ERR(i))
- set_bit(0, &pd_chan->err_status);
+ if (i < 8) {
+ if (sts0 & DMA_STATUS_IRQ(i)) {
+ if (sts0 & DMA_STATUS0_ERR(i))
+ set_bit(0, &pd_chan->err_status);
- tasklet_schedule(&pd_chan->tasklet);
- ret = IRQ_HANDLED;
+ tasklet_schedule(&pd_chan->tasklet);
+ ret0 = IRQ_HANDLED;
+ }
+ } else {
+ if (sts2 & DMA_STATUS_IRQ(i - 8)) {
+ if (sts2 & DMA_STATUS2_ERR(i))
+ set_bit(0, &pd_chan->err_status);
+
+ tasklet_schedule(&pd_chan->tasklet);
+ ret2 = IRQ_HANDLED;
+ }
}
-
}
/* clear interrupt bits in status register */
- dma_writel(pd, STS0, sts0);
+ if (ret0)
+ dma_writel(pd, STS0, sts0);
+ if (ret2)
+ dma_writel(pd, STS2, sts2);
- return ret;
+ return ret0 | ret2;
}
#ifdef CONFIG_PM
diff --git a/drivers/dma/pl330.c b/drivers/dma/pl330.c
index 6abe1ec..00eee59 100644
--- a/drivers/dma/pl330.c
+++ b/drivers/dma/pl330.c
@@ -82,7 +82,7 @@
spinlock_t pool_lock;
/* Peripheral channels connected to this DMAC */
- struct dma_pl330_chan peripherals[0]; /* keep at end */
+ struct dma_pl330_chan *peripherals; /* keep at end */
};
struct dma_pl330_desc {
@@ -451,8 +451,13 @@
desc->txd.cookie = 0;
async_tx_ack(&desc->txd);
- desc->req.rqtype = peri->rqtype;
- desc->req.peri = peri->peri_id;
+ if (peri) {
+ desc->req.rqtype = peri->rqtype;
+ desc->req.peri = peri->peri_id;
+ } else {
+ desc->req.rqtype = MEMTOMEM;
+ desc->req.peri = 0;
+ }
dma_async_tx_descriptor_init(&desc->txd, &pch->chan);
@@ -529,10 +534,10 @@
struct pl330_info *pi;
int burst;
- if (unlikely(!pch || !len || !peri))
+ if (unlikely(!pch || !len))
return NULL;
- if (peri->rqtype != MEMTOMEM)
+ if (peri && peri->rqtype != MEMTOMEM)
return NULL;
pi = &pch->dmac->pif;
@@ -577,7 +582,7 @@
int i, burst_size;
dma_addr_t addr;
- if (unlikely(!pch || !sgl || !sg_len))
+ if (unlikely(!pch || !sgl || !sg_len || !peri))
return NULL;
/* Make sure the direction is consistent */
@@ -666,17 +671,12 @@
struct dma_device *pd;
struct resource *res;
int i, ret, irq;
+ int num_chan;
pdat = adev->dev.platform_data;
- if (!pdat || !pdat->nr_valid_peri) {
- dev_err(&adev->dev, "platform data missing\n");
- return -ENODEV;
- }
-
/* Allocate a new DMAC and its Channels */
- pdmac = kzalloc(pdat->nr_valid_peri * sizeof(*pch)
- + sizeof(*pdmac), GFP_KERNEL);
+ pdmac = kzalloc(sizeof(*pdmac), GFP_KERNEL);
if (!pdmac) {
dev_err(&adev->dev, "unable to allocate mem\n");
return -ENOMEM;
@@ -685,7 +685,7 @@
pi = &pdmac->pif;
pi->dev = &adev->dev;
pi->pl330_data = NULL;
- pi->mcbufsz = pdat->mcbuf_sz;
+ pi->mcbufsz = pdat ? pdat->mcbuf_sz : 0;
res = &adev->res;
request_mem_region(res->start, resource_size(res), "dma-pl330");
@@ -717,27 +717,35 @@
INIT_LIST_HEAD(&pd->channels);
/* Initialize channel parameters */
- for (i = 0; i < pdat->nr_valid_peri; i++) {
- struct dma_pl330_peri *peri = &pdat->peri[i];
- pch = &pdmac->peripherals[i];
+ num_chan = max(pdat ? pdat->nr_valid_peri : 0, (u8)pi->pcfg.num_chan);
+ pdmac->peripherals = kzalloc(num_chan * sizeof(*pch), GFP_KERNEL);
- switch (peri->rqtype) {
- case MEMTOMEM:
+ for (i = 0; i < num_chan; i++) {
+ pch = &pdmac->peripherals[i];
+ if (pdat) {
+ struct dma_pl330_peri *peri = &pdat->peri[i];
+
+ switch (peri->rqtype) {
+ case MEMTOMEM:
+ dma_cap_set(DMA_MEMCPY, pd->cap_mask);
+ break;
+ case MEMTODEV:
+ case DEVTOMEM:
+ dma_cap_set(DMA_SLAVE, pd->cap_mask);
+ break;
+ default:
+ dev_err(&adev->dev, "DEVTODEV Not Supported\n");
+ continue;
+ }
+ pch->chan.private = peri;
+ } else {
dma_cap_set(DMA_MEMCPY, pd->cap_mask);
- break;
- case MEMTODEV:
- case DEVTOMEM:
- dma_cap_set(DMA_SLAVE, pd->cap_mask);
- break;
- default:
- dev_err(&adev->dev, "DEVTODEV Not Supported\n");
- continue;
+ pch->chan.private = NULL;
}
INIT_LIST_HEAD(&pch->work_list);
spin_lock_init(&pch->lock);
pch->pl330_chid = NULL;
- pch->chan.private = peri;
pch->chan.device = pd;
pch->chan.chan_id = i;
pch->dmac = pdmac;
diff --git a/drivers/dma/ste_dma40.c b/drivers/dma/ste_dma40.c
index 8f222d4..75ba586 100644
--- a/drivers/dma/ste_dma40.c
+++ b/drivers/dma/ste_dma40.c
@@ -13,6 +13,7 @@
#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/err.h>
+#include <linux/amba/bus.h>
#include <plat/ste_dma40.h>
@@ -44,9 +45,6 @@
#define D40_ALLOC_PHY (1 << 30)
#define D40_ALLOC_LOG_FREE 0
-/* Hardware designer of the block */
-#define D40_HW_DESIGNER 0x8
-
/**
* enum 40_command - The different commands and/or statuses.
*
@@ -185,6 +183,8 @@
* @log_def: Default logical channel settings.
* @lcla: Space for one dst src pair for logical channel transfers.
* @lcpa: Pointer to dst and src lcpa settings.
+ * @runtime_addr: runtime configured address.
+ * @runtime_direction: runtime configured direction.
*
* This struct can either "be" a logical or a physical channel.
*/
@@ -199,6 +199,7 @@
struct dma_chan chan;
struct tasklet_struct tasklet;
struct list_head client;
+ struct list_head pending_queue;
struct list_head active;
struct list_head queue;
struct stedma40_chan_cfg dma_cfg;
@@ -644,7 +645,20 @@
static void d40_desc_queue(struct d40_chan *d40c, struct d40_desc *desc)
{
- list_add_tail(&desc->node, &d40c->queue);
+ list_add_tail(&desc->node, &d40c->pending_queue);
+}
+
+static struct d40_desc *d40_first_pending(struct d40_chan *d40c)
+{
+ struct d40_desc *d;
+
+ if (list_empty(&d40c->pending_queue))
+ return NULL;
+
+ d = list_first_entry(&d40c->pending_queue,
+ struct d40_desc,
+ node);
+ return d;
}
static struct d40_desc *d40_first_queued(struct d40_chan *d40c)
@@ -801,6 +815,11 @@
d40_desc_free(d40c, d40d);
}
+ /* Release pending descriptors */
+ while ((d40d = d40_first_pending(d40c))) {
+ d40_desc_remove(d40d);
+ d40_desc_free(d40c, d40d);
+ }
d40c->pending_tx = 0;
d40c->busy = false;
@@ -2091,7 +2110,7 @@
struct scatterlist *sg;
int i;
- sg = kcalloc(periods + 1, sizeof(struct scatterlist), GFP_KERNEL);
+ sg = kcalloc(periods + 1, sizeof(struct scatterlist), GFP_NOWAIT);
for (i = 0; i < periods; i++) {
sg_dma_address(&sg[i]) = dma_addr;
sg_dma_len(&sg[i]) = period_len;
@@ -2151,24 +2170,87 @@
spin_lock_irqsave(&d40c->lock, flags);
- /* Busy means that pending jobs are already being processed */
+ list_splice_tail_init(&d40c->pending_queue, &d40c->queue);
+
+ /* Busy means that queued jobs are already being processed */
if (!d40c->busy)
(void) d40_queue_start(d40c);
spin_unlock_irqrestore(&d40c->lock, flags);
}
+static int
+dma40_config_to_halfchannel(struct d40_chan *d40c,
+ struct stedma40_half_channel_info *info,
+ enum dma_slave_buswidth width,
+ u32 maxburst)
+{
+ enum stedma40_periph_data_width addr_width;
+ int psize;
+
+ switch (width) {
+ case DMA_SLAVE_BUSWIDTH_1_BYTE:
+ addr_width = STEDMA40_BYTE_WIDTH;
+ break;
+ case DMA_SLAVE_BUSWIDTH_2_BYTES:
+ addr_width = STEDMA40_HALFWORD_WIDTH;
+ break;
+ case DMA_SLAVE_BUSWIDTH_4_BYTES:
+ addr_width = STEDMA40_WORD_WIDTH;
+ break;
+ case DMA_SLAVE_BUSWIDTH_8_BYTES:
+ addr_width = STEDMA40_DOUBLEWORD_WIDTH;
+ break;
+ default:
+ dev_err(d40c->base->dev,
+ "illegal peripheral address width "
+ "requested (%d)\n",
+ width);
+ return -EINVAL;
+ }
+
+ if (chan_is_logical(d40c)) {
+ if (maxburst >= 16)
+ psize = STEDMA40_PSIZE_LOG_16;
+ else if (maxburst >= 8)
+ psize = STEDMA40_PSIZE_LOG_8;
+ else if (maxburst >= 4)
+ psize = STEDMA40_PSIZE_LOG_4;
+ else
+ psize = STEDMA40_PSIZE_LOG_1;
+ } else {
+ if (maxburst >= 16)
+ psize = STEDMA40_PSIZE_PHY_16;
+ else if (maxburst >= 8)
+ psize = STEDMA40_PSIZE_PHY_8;
+ else if (maxburst >= 4)
+ psize = STEDMA40_PSIZE_PHY_4;
+ else
+ psize = STEDMA40_PSIZE_PHY_1;
+ }
+
+ info->data_width = addr_width;
+ info->psize = psize;
+ info->flow_ctrl = STEDMA40_NO_FLOW_CTRL;
+
+ return 0;
+}
+
/* Runtime reconfiguration extension */
-static void d40_set_runtime_config(struct dma_chan *chan,
- struct dma_slave_config *config)
+static int d40_set_runtime_config(struct dma_chan *chan,
+ struct dma_slave_config *config)
{
struct d40_chan *d40c = container_of(chan, struct d40_chan, chan);
struct stedma40_chan_cfg *cfg = &d40c->dma_cfg;
- enum dma_slave_buswidth config_addr_width;
+ enum dma_slave_buswidth src_addr_width, dst_addr_width;
dma_addr_t config_addr;
- u32 config_maxburst;
- enum stedma40_periph_data_width addr_width;
- int psize;
+ u32 src_maxburst, dst_maxburst;
+ int ret;
+
+ src_addr_width = config->src_addr_width;
+ src_maxburst = config->src_maxburst;
+ dst_addr_width = config->dst_addr_width;
+ dst_maxburst = config->dst_maxburst;
if (config->direction == DMA_FROM_DEVICE) {
dma_addr_t dev_addr_rx =
@@ -2187,8 +2269,11 @@
cfg->dir);
cfg->dir = STEDMA40_PERIPH_TO_MEM;
- config_addr_width = config->src_addr_width;
- config_maxburst = config->src_maxburst;
+ /* Configure the memory side */
+ if (dst_addr_width == DMA_SLAVE_BUSWIDTH_UNDEFINED)
+ dst_addr_width = src_addr_width;
+ if (dst_maxburst == 0)
+ dst_maxburst = src_maxburst;
} else if (config->direction == DMA_TO_DEVICE) {
dma_addr_t dev_addr_tx =
@@ -2207,68 +2292,39 @@
cfg->dir);
cfg->dir = STEDMA40_MEM_TO_PERIPH;
- config_addr_width = config->dst_addr_width;
- config_maxburst = config->dst_maxburst;
-
+ /* Configure the memory side */
+ if (src_addr_width == DMA_SLAVE_BUSWIDTH_UNDEFINED)
+ src_addr_width = dst_addr_width;
+ if (src_maxburst == 0)
+ src_maxburst = dst_maxburst;
} else {
dev_err(d40c->base->dev,
"unrecognized channel direction %d\n",
config->direction);
- return;
+ return -EINVAL;
}
- switch (config_addr_width) {
- case DMA_SLAVE_BUSWIDTH_1_BYTE:
- addr_width = STEDMA40_BYTE_WIDTH;
- break;
- case DMA_SLAVE_BUSWIDTH_2_BYTES:
- addr_width = STEDMA40_HALFWORD_WIDTH;
- break;
- case DMA_SLAVE_BUSWIDTH_4_BYTES:
- addr_width = STEDMA40_WORD_WIDTH;
- break;
- case DMA_SLAVE_BUSWIDTH_8_BYTES:
- addr_width = STEDMA40_DOUBLEWORD_WIDTH;
- break;
- default:
+ if (src_maxburst * src_addr_width != dst_maxburst * dst_addr_width) {
dev_err(d40c->base->dev,
- "illegal peripheral address width "
- "requested (%d)\n",
- config->src_addr_width);
- return;
+ "src/dst width/maxburst mismatch: %d*%d != %d*%d\n",
+ src_maxburst,
+ src_addr_width,
+ dst_maxburst,
+ dst_addr_width);
+ return -EINVAL;
}
- if (chan_is_logical(d40c)) {
- if (config_maxburst >= 16)
- psize = STEDMA40_PSIZE_LOG_16;
- else if (config_maxburst >= 8)
- psize = STEDMA40_PSIZE_LOG_8;
- else if (config_maxburst >= 4)
- psize = STEDMA40_PSIZE_LOG_4;
- else
- psize = STEDMA40_PSIZE_LOG_1;
- } else {
- if (config_maxburst >= 16)
- psize = STEDMA40_PSIZE_PHY_16;
- else if (config_maxburst >= 8)
- psize = STEDMA40_PSIZE_PHY_8;
- else if (config_maxburst >= 4)
- psize = STEDMA40_PSIZE_PHY_4;
- else if (config_maxburst >= 2)
- psize = STEDMA40_PSIZE_PHY_2;
- else
- psize = STEDMA40_PSIZE_PHY_1;
- }
+ ret = dma40_config_to_halfchannel(d40c, &cfg->src_info,
+ src_addr_width,
+ src_maxburst);
+ if (ret)
+ return ret;
- /* Set up all the endpoint configs */
- cfg->src_info.data_width = addr_width;
- cfg->src_info.psize = psize;
- cfg->src_info.big_endian = false;
- cfg->src_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL;
- cfg->dst_info.data_width = addr_width;
- cfg->dst_info.psize = psize;
- cfg->dst_info.big_endian = false;
- cfg->dst_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL;
+ ret = dma40_config_to_halfchannel(d40c, &cfg->dst_info,
+ dst_addr_width,
+ dst_maxburst);
+ if (ret)
+ return ret;
/* Fill in register values */
if (chan_is_logical(d40c))
@@ -2281,12 +2337,14 @@
d40c->runtime_addr = config_addr;
d40c->runtime_direction = config->direction;
dev_dbg(d40c->base->dev,
- "configured channel %s for %s, data width %d, "
- "maxburst %d bytes, LE, no flow control\n",
+ "configured channel %s for %s, data width %d/%d, "
+ "maxburst %d/%d elements, LE, no flow control\n",
dma_chan_name(chan),
(config->direction == DMA_FROM_DEVICE) ? "RX" : "TX",
- config_addr_width,
- config_maxburst);
+ src_addr_width, dst_addr_width,
+ src_maxburst, dst_maxburst);
+
+ return 0;
}
static int d40_control(struct dma_chan *chan, enum dma_ctrl_cmd cmd,
@@ -2307,9 +2365,8 @@
case DMA_RESUME:
return d40_resume(d40c);
case DMA_SLAVE_CONFIG:
- d40_set_runtime_config(chan,
+ return d40_set_runtime_config(chan,
(struct dma_slave_config *) arg);
- return 0;
default:
break;
}
@@ -2340,6 +2397,7 @@
INIT_LIST_HEAD(&d40c->active);
INIT_LIST_HEAD(&d40c->queue);
+ INIT_LIST_HEAD(&d40c->pending_queue);
INIT_LIST_HEAD(&d40c->client);
tasklet_init(&d40c->tasklet, dma_tasklet,
@@ -2501,25 +2559,6 @@
static struct d40_base * __init d40_hw_detect_init(struct platform_device *pdev)
{
- static const struct d40_reg_val dma_id_regs[] = {
- /* Peripheral Id */
- { .reg = D40_DREG_PERIPHID0, .val = 0x0040},
- { .reg = D40_DREG_PERIPHID1, .val = 0x0000},
- /*
- * D40_DREG_PERIPHID2 Depends on HW revision:
- * DB8500ed has 0x0008,
- * ? has 0x0018,
- * DB8500v1 has 0x0028
- * DB8500v2 has 0x0038
- */
- { .reg = D40_DREG_PERIPHID3, .val = 0x0000},
-
- /* PCell Id */
- { .reg = D40_DREG_CELLID0, .val = 0x000d},
- { .reg = D40_DREG_CELLID1, .val = 0x00f0},
- { .reg = D40_DREG_CELLID2, .val = 0x0005},
- { .reg = D40_DREG_CELLID3, .val = 0x00b1}
- };
struct stedma40_platform_data *plat_data;
struct clk *clk = NULL;
void __iomem *virtbase = NULL;
@@ -2528,8 +2567,9 @@
int num_log_chans = 0;
int num_phy_chans;
int i;
- u32 val;
- u32 rev;
+ u32 pid;
+ u32 cid;
+ u8 rev;
clk = clk_get(&pdev->dev, NULL);
@@ -2553,32 +2593,32 @@
if (!virtbase)
goto failure;
- /* HW version check */
- for (i = 0; i < ARRAY_SIZE(dma_id_regs); i++) {
- if (dma_id_regs[i].val !=
- readl(virtbase + dma_id_regs[i].reg)) {
- d40_err(&pdev->dev,
- "Unknown hardware! Expected 0x%x at 0x%x but got 0x%x\n",
- dma_id_regs[i].val,
- dma_id_regs[i].reg,
- readl(virtbase + dma_id_regs[i].reg));
- goto failure;
- }
- }
+ /* This is just a regular AMBA PrimeCell ID actually */
+ for (pid = 0, i = 0; i < 4; i++)
+ pid |= (readl(virtbase + resource_size(res) - 0x20 + 4 * i)
+ & 255) << (i * 8);
+ for (cid = 0, i = 0; i < 4; i++)
+ cid |= (readl(virtbase + resource_size(res) - 0x10 + 4 * i)
+ & 255) << (i * 8);
- /* Get silicon revision and designer */
- val = readl(virtbase + D40_DREG_PERIPHID2);
-
- if ((val & D40_DREG_PERIPHID2_DESIGNER_MASK) !=
- D40_HW_DESIGNER) {
- d40_err(&pdev->dev, "Unknown designer! Got %x wanted %x\n",
- val & D40_DREG_PERIPHID2_DESIGNER_MASK,
- D40_HW_DESIGNER);
+ if (cid != AMBA_CID) {
+ d40_err(&pdev->dev, "Unknown hardware! No PrimeCell ID\n");
goto failure;
}
-
- rev = (val & D40_DREG_PERIPHID2_REV_MASK) >>
- D40_DREG_PERIPHID2_REV_POS;
+ if (AMBA_MANF_BITS(pid) != AMBA_VENDOR_ST) {
+ d40_err(&pdev->dev, "Unknown designer! Got %x wanted %x\n",
+ AMBA_MANF_BITS(pid),
+ AMBA_VENDOR_ST);
+ goto failure;
+ }
+ /*
+ * HW revision:
+ * DB8500ed has revision 0
+ * ? has revision 1
+ * DB8500v1 has revision 2
+ * DB8500v2 has revision 3
+ */
+ rev = AMBA_REV_BITS(pid);
/* The number of physical channels on this HW */
num_phy_chans = 4 * (readl(virtbase + D40_DREG_ICFG) & 0x7) + 4;
diff --git a/drivers/dma/ste_dma40_ll.h b/drivers/dma/ste_dma40_ll.h
index 195ee65..b44c4551 100644
--- a/drivers/dma/ste_dma40_ll.h
+++ b/drivers/dma/ste_dma40_ll.h
@@ -184,9 +184,6 @@
#define D40_DREG_PERIPHID0 0xFE0
#define D40_DREG_PERIPHID1 0xFE4
#define D40_DREG_PERIPHID2 0xFE8
-#define D40_DREG_PERIPHID2_REV_POS 4
-#define D40_DREG_PERIPHID2_REV_MASK (0xf << D40_DREG_PERIPHID2_REV_POS)
-#define D40_DREG_PERIPHID2_DESIGNER_MASK 0xf
#define D40_DREG_PERIPHID3 0xFEC
#define D40_DREG_CELLID0 0xFF0
#define D40_DREG_CELLID1 0xFF4
diff --git a/drivers/spi/ep93xx_spi.c b/drivers/spi/ep93xx_spi.c
index d357007..1cf64547 100644
--- a/drivers/spi/ep93xx_spi.c
+++ b/drivers/spi/ep93xx_spi.c
@@ -1,7 +1,7 @@
/*
* Driver for Cirrus Logic EP93xx SPI controller.
*
- * Copyright (c) 2010 Mika Westerberg
+ * Copyright (C) 2010-2011 Mika Westerberg
*
* Explicit FIFO handling code was inspired by amba-pl022 driver.
*
@@ -21,13 +21,16 @@
#include <linux/err.h>
#include <linux/delay.h>
#include <linux/device.h>
+#include <linux/dmaengine.h>
#include <linux/bitops.h>
#include <linux/interrupt.h>
#include <linux/platform_device.h>
#include <linux/workqueue.h>
#include <linux/sched.h>
+#include <linux/scatterlist.h>
#include <linux/spi/spi.h>
+#include <mach/dma.h>
#include <mach/ep93xx_spi.h>
#define SSPCR0 0x0000
@@ -71,6 +74,7 @@
* @pdev: pointer to platform device
* @clk: clock for the controller
* @regs_base: pointer to ioremap()'d registers
+ * @sspdr_phys: physical address of the SSPDR register
* @irq: IRQ number used by the driver
* @min_rate: minimum clock rate (in Hz) supported by the controller
* @max_rate: maximum clock rate (in Hz) supported by the controller
@@ -84,6 +88,14 @@
* @rx: current byte in transfer to receive
* @fifo_level: how full is FIFO (%0..%SPI_FIFO_SIZE - %1). Receiving one
* frame decreases this level and sending one frame increases it.
+ * @dma_rx: RX DMA channel
+ * @dma_tx: TX DMA channel
+ * @dma_rx_data: RX parameters passed to the DMA engine
+ * @dma_tx_data: TX parameters passed to the DMA engine
+ * @rx_sgt: sg table for RX transfers
+ * @tx_sgt: sg table for TX transfers
+ * @zeropage: dummy page used as RX buffer when only TX buffer is passed in by
+ * the client
*
* This structure holds EP93xx SPI controller specific information. When
* @running is %true, driver accepts transfer requests from protocol drivers.
@@ -100,6 +112,7 @@
const struct platform_device *pdev;
struct clk *clk;
void __iomem *regs_base;
+ unsigned long sspdr_phys;
int irq;
unsigned long min_rate;
unsigned long max_rate;
@@ -112,6 +125,13 @@
size_t tx;
size_t rx;
size_t fifo_level;
+ struct dma_chan *dma_rx;
+ struct dma_chan *dma_tx;
+ struct ep93xx_dma_data dma_rx_data;
+ struct ep93xx_dma_data dma_tx_data;
+ struct sg_table rx_sgt;
+ struct sg_table tx_sgt;
+ void *zeropage;
};
/**
@@ -496,14 +516,195 @@
espi->fifo_level++;
}
- if (espi->rx == t->len) {
- msg->actual_length += t->len;
+ if (espi->rx == t->len)
return 0;
- }
return -EINPROGRESS;
}
+static void ep93xx_spi_pio_transfer(struct ep93xx_spi *espi)
+{
+ /*
+ * Now everything is set up for the current transfer. We prime the TX
+ * FIFO, enable interrupts, and wait for the transfer to complete.
+ */
+ if (ep93xx_spi_read_write(espi)) {
+ ep93xx_spi_enable_interrupts(espi);
+ wait_for_completion(&espi->wait);
+ }
+}
+
+/**
+ * ep93xx_spi_dma_prepare() - prepares a DMA transfer
+ * @espi: ep93xx SPI controller struct
+ * @dir: DMA transfer direction
+ *
+ * Function configures the DMA, maps the buffer and prepares the DMA
+ * descriptor. Returns a valid DMA descriptor in case of success and ERR_PTR
+ * in case of failure.
+ */
+static struct dma_async_tx_descriptor *
+ep93xx_spi_dma_prepare(struct ep93xx_spi *espi, enum dma_data_direction dir)
+{
+ struct spi_transfer *t = espi->current_msg->state;
+ struct dma_async_tx_descriptor *txd;
+ enum dma_slave_buswidth buswidth;
+ struct dma_slave_config conf;
+ struct scatterlist *sg;
+ struct sg_table *sgt;
+ struct dma_chan *chan;
+ const void *buf, *pbuf;
+ size_t len = t->len;
+ int i, ret, nents;
+
+ if (bits_per_word(espi) > 8)
+ buswidth = DMA_SLAVE_BUSWIDTH_2_BYTES;
+ else
+ buswidth = DMA_SLAVE_BUSWIDTH_1_BYTE;
+
+ memset(&conf, 0, sizeof(conf));
+ conf.direction = dir;
+
+ if (dir == DMA_FROM_DEVICE) {
+ chan = espi->dma_rx;
+ buf = t->rx_buf;
+ sgt = &espi->rx_sgt;
+
+ conf.src_addr = espi->sspdr_phys;
+ conf.src_addr_width = buswidth;
+ } else {
+ chan = espi->dma_tx;
+ buf = t->tx_buf;
+ sgt = &espi->tx_sgt;
+
+ conf.dst_addr = espi->sspdr_phys;
+ conf.dst_addr_width = buswidth;
+ }
+
+ ret = dmaengine_slave_config(chan, &conf);
+ if (ret)
+ return ERR_PTR(ret);
+
+ /*
+ * We need to split the transfer into PAGE_SIZE'd chunks. This is
+ * because we are using @espi->zeropage to provide a zero RX buffer
+ * for the TX transfers and we have only allocated one page for that.
+ *
+ * For performance reasons we allocate a new sg_table only when
+ * needed. Otherwise we will re-use the current one. Eventually the
+ * last sg_table is released in ep93xx_spi_release_dma().
+ */
+
+ nents = DIV_ROUND_UP(len, PAGE_SIZE);
+ if (nents != sgt->nents) {
+ sg_free_table(sgt);
+
+ ret = sg_alloc_table(sgt, nents, GFP_KERNEL);
+ if (ret)
+ return ERR_PTR(ret);
+ }
+
+ pbuf = buf;
+ for_each_sg(sgt->sgl, sg, sgt->nents, i) {
+ size_t bytes = min_t(size_t, len, PAGE_SIZE);
+
+ if (buf) {
+ sg_set_page(sg, virt_to_page(pbuf), bytes,
+ offset_in_page(pbuf));
+ } else {
+ sg_set_page(sg, virt_to_page(espi->zeropage),
+ bytes, 0);
+ }
+
+ pbuf += bytes;
+ len -= bytes;
+ }
+
+ if (WARN_ON(len)) {
+ dev_warn(&espi->pdev->dev, "len = %d expected 0!", len);
+ return ERR_PTR(-EINVAL);
+ }
+
+ nents = dma_map_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
+ if (!nents)
+ return ERR_PTR(-ENOMEM);
+
+ txd = chan->device->device_prep_slave_sg(chan, sgt->sgl, nents,
+ dir, DMA_CTRL_ACK);
+ if (!txd) {
+ dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
+ return ERR_PTR(-ENOMEM);
+ }
+ return txd;
+}
+
+/**
+ * ep93xx_spi_dma_finish() - finishes with a DMA transfer
+ * @espi: ep93xx SPI controller struct
+ * @dir: DMA transfer direction
+ *
+ * Function finishes with the DMA transfer. After this, the DMA buffer is
+ * unmapped.
+ */
+static void ep93xx_spi_dma_finish(struct ep93xx_spi *espi,
+ enum dma_data_direction dir)
+{
+ struct dma_chan *chan;
+ struct sg_table *sgt;
+
+ if (dir == DMA_FROM_DEVICE) {
+ chan = espi->dma_rx;
+ sgt = &espi->rx_sgt;
+ } else {
+ chan = espi->dma_tx;
+ sgt = &espi->tx_sgt;
+ }
+
+ dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
+}
+
+static void ep93xx_spi_dma_callback(void *callback_param)
+{
+ complete(callback_param);
+}
+
+static void ep93xx_spi_dma_transfer(struct ep93xx_spi *espi)
+{
+ struct spi_message *msg = espi->current_msg;
+ struct dma_async_tx_descriptor *rxd, *txd;
+
+ rxd = ep93xx_spi_dma_prepare(espi, DMA_FROM_DEVICE);
+ if (IS_ERR(rxd)) {
+ dev_err(&espi->pdev->dev, "DMA RX failed: %ld\n", PTR_ERR(rxd));
+ msg->status = PTR_ERR(rxd);
+ return;
+ }
+
+ txd = ep93xx_spi_dma_prepare(espi, DMA_TO_DEVICE);
+ if (IS_ERR(txd)) {
+ ep93xx_spi_dma_finish(espi, DMA_FROM_DEVICE);
+ dev_err(&espi->pdev->dev, "DMA TX failed: %ld\n", PTR_ERR(rxd));
+ msg->status = PTR_ERR(txd);
+ return;
+ }
+
+ /* We are ready when RX is done */
+ rxd->callback = ep93xx_spi_dma_callback;
+ rxd->callback_param = &espi->wait;
+
+ /* Now submit both descriptors and wait while they finish */
+ dmaengine_submit(rxd);
+ dmaengine_submit(txd);
+
+ dma_async_issue_pending(espi->dma_rx);
+ dma_async_issue_pending(espi->dma_tx);
+
+ wait_for_completion(&espi->wait);
+
+ ep93xx_spi_dma_finish(espi, DMA_TO_DEVICE);
+ ep93xx_spi_dma_finish(espi, DMA_FROM_DEVICE);
+}
+
/**
* ep93xx_spi_process_transfer() - processes one SPI transfer
* @espi: ep93xx SPI controller struct
@@ -556,13 +757,14 @@
espi->tx = 0;
/*
- * Now everything is set up for the current transfer. We prime the TX
- * FIFO, enable interrupts, and wait for the transfer to complete.
+ * There is no point of setting up DMA for the transfers which will
+ * fit into the FIFO and can be transferred with a single interrupt.
+ * So in these cases we will be using PIO and don't bother for DMA.
*/
- if (ep93xx_spi_read_write(espi)) {
- ep93xx_spi_enable_interrupts(espi);
- wait_for_completion(&espi->wait);
- }
+ if (espi->dma_rx && t->len > SPI_FIFO_SIZE)
+ ep93xx_spi_dma_transfer(espi);
+ else
+ ep93xx_spi_pio_transfer(espi);
/*
* In case of error during transmit, we bail out from processing
@@ -571,6 +773,8 @@
if (msg->status)
return;
+ msg->actual_length += t->len;
+
/*
* After this transfer is finished, perform any possible
* post-transfer actions requested by the protocol driver.
@@ -752,6 +956,75 @@
return IRQ_HANDLED;
}
+static bool ep93xx_spi_dma_filter(struct dma_chan *chan, void *filter_param)
+{
+ if (ep93xx_dma_chan_is_m2p(chan))
+ return false;
+
+ chan->private = filter_param;
+ return true;
+}
+
+static int ep93xx_spi_setup_dma(struct ep93xx_spi *espi)
+{
+ dma_cap_mask_t mask;
+ int ret;
+
+ espi->zeropage = (void *)get_zeroed_page(GFP_KERNEL);
+ if (!espi->zeropage)
+ return -ENOMEM;
+
+ dma_cap_zero(mask);
+ dma_cap_set(DMA_SLAVE, mask);
+
+ espi->dma_rx_data.port = EP93XX_DMA_SSP;
+ espi->dma_rx_data.direction = DMA_FROM_DEVICE;
+ espi->dma_rx_data.name = "ep93xx-spi-rx";
+
+ espi->dma_rx = dma_request_channel(mask, ep93xx_spi_dma_filter,
+ &espi->dma_rx_data);
+ if (!espi->dma_rx) {
+ ret = -ENODEV;
+ goto fail_free_page;
+ }
+
+ espi->dma_tx_data.port = EP93XX_DMA_SSP;
+ espi->dma_tx_data.direction = DMA_TO_DEVICE;
+ espi->dma_tx_data.name = "ep93xx-spi-tx";
+
+ espi->dma_tx = dma_request_channel(mask, ep93xx_spi_dma_filter,
+ &espi->dma_tx_data);
+ if (!espi->dma_tx) {
+ ret = -ENODEV;
+ goto fail_release_rx;
+ }
+
+ return 0;
+
+fail_release_rx:
+ dma_release_channel(espi->dma_rx);
+ espi->dma_rx = NULL;
+fail_free_page:
+ free_page((unsigned long)espi->zeropage);
+
+ return ret;
+}
+
+static void ep93xx_spi_release_dma(struct ep93xx_spi *espi)
+{
+ if (espi->dma_rx) {
+ dma_release_channel(espi->dma_rx);
+ sg_free_table(&espi->rx_sgt);
+ }
+ if (espi->dma_tx) {
+ dma_release_channel(espi->dma_tx);
+ sg_free_table(&espi->tx_sgt);
+ }
+
+ if (espi->zeropage)
+ free_page((unsigned long)espi->zeropage);
+}
+
static int __init ep93xx_spi_probe(struct platform_device *pdev)
{
struct spi_master *master;
@@ -818,6 +1091,7 @@
goto fail_put_clock;
}
+ espi->sspdr_phys = res->start + SSPDR;
espi->regs_base = ioremap(res->start, resource_size(res));
if (!espi->regs_base) {
dev_err(&pdev->dev, "failed to map resources\n");
@@ -832,10 +1106,13 @@
goto fail_unmap_regs;
}
+ if (info->use_dma && ep93xx_spi_setup_dma(espi))
+ dev_warn(&pdev->dev, "DMA setup failed. Falling back to PIO\n");
+
espi->wq = create_singlethread_workqueue("ep93xx_spid");
if (!espi->wq) {
dev_err(&pdev->dev, "unable to create workqueue\n");
- goto fail_free_irq;
+ goto fail_free_dma;
}
INIT_WORK(&espi->msg_work, ep93xx_spi_work);
INIT_LIST_HEAD(&espi->msg_queue);
@@ -857,7 +1134,8 @@
fail_free_queue:
destroy_workqueue(espi->wq);
-fail_free_irq:
+fail_free_dma:
+ ep93xx_spi_release_dma(espi);
free_irq(espi->irq, espi);
fail_unmap_regs:
iounmap(espi->regs_base);
@@ -901,6 +1179,7 @@
}
spin_unlock_irq(&espi->lock);
+ ep93xx_spi_release_dma(espi);
free_irq(espi->irq, espi);
iounmap(espi->regs_base);
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
diff --git a/include/linux/amba/pl08x.h b/include/linux/amba/pl08x.h
index 3111385..e6e28f3 100644
--- a/include/linux/amba/pl08x.h
+++ b/include/linux/amba/pl08x.h
@@ -172,8 +172,11 @@
int phychan_hold;
struct tasklet_struct tasklet;
char *name;
- struct pl08x_channel_data *cd;
- dma_addr_t runtime_addr;
+ const struct pl08x_channel_data *cd;
+ dma_addr_t src_addr;
+ dma_addr_t dst_addr;
+ u32 src_cctl;
+ u32 dst_cctl;
enum dma_data_direction runtime_direction;
dma_cookie_t lc;
struct list_head pend_list;
@@ -202,7 +205,7 @@
* @mem_buses: buses which memory can be accessed from: PL08X_AHB1 | PL08X_AHB2
*/
struct pl08x_platform_data {
- struct pl08x_channel_data *slave_channels;
+ const struct pl08x_channel_data *slave_channels;
unsigned int num_slave_channels;
struct pl08x_channel_data memcpy_channel;
int (*get_signal)(struct pl08x_dma_chan *);
diff --git a/sound/soc/ep93xx/ep93xx-ac97.c b/sound/soc/ep93xx/ep93xx-ac97.c
index 104e95c..c7417c7 100644
--- a/sound/soc/ep93xx/ep93xx-ac97.c
+++ b/sound/soc/ep93xx/ep93xx-ac97.c
@@ -106,12 +106,12 @@
static struct ep93xx_pcm_dma_params ep93xx_ac97_pcm_out = {
.name = "ac97-pcm-out",
- .dma_port = EP93XX_DMA_M2P_PORT_AAC1,
+ .dma_port = EP93XX_DMA_AAC1,
};
static struct ep93xx_pcm_dma_params ep93xx_ac97_pcm_in = {
.name = "ac97-pcm-in",
- .dma_port = EP93XX_DMA_M2P_PORT_AAC1,
+ .dma_port = EP93XX_DMA_AAC1,
};
static inline unsigned ep93xx_ac97_read_reg(struct ep93xx_ac97_info *info,
diff --git a/sound/soc/ep93xx/ep93xx-i2s.c b/sound/soc/ep93xx/ep93xx-i2s.c
index 042f4e9..30df425 100644
--- a/sound/soc/ep93xx/ep93xx-i2s.c
+++ b/sound/soc/ep93xx/ep93xx-i2s.c
@@ -70,11 +70,11 @@
struct ep93xx_pcm_dma_params ep93xx_i2s_dma_params[] = {
[SNDRV_PCM_STREAM_PLAYBACK] = {
.name = "i2s-pcm-out",
- .dma_port = EP93XX_DMA_M2P_PORT_I2S1,
+ .dma_port = EP93XX_DMA_I2S1,
},
[SNDRV_PCM_STREAM_CAPTURE] = {
.name = "i2s-pcm-in",
- .dma_port = EP93XX_DMA_M2P_PORT_I2S1,
+ .dma_port = EP93XX_DMA_I2S1,
},
};
diff --git a/sound/soc/ep93xx/ep93xx-pcm.c b/sound/soc/ep93xx/ep93xx-pcm.c
index a456e49..a07f99c 100644
--- a/sound/soc/ep93xx/ep93xx-pcm.c
+++ b/sound/soc/ep93xx/ep93xx-pcm.c
@@ -16,6 +16,7 @@
#include <linux/init.h>
#include <linux/device.h>
#include <linux/slab.h>
+#include <linux/dmaengine.h>
#include <linux/dma-mapping.h>
#include <sound/core.h>
@@ -53,43 +54,34 @@
struct ep93xx_runtime_data
{
- struct ep93xx_dma_m2p_client cl;
- struct ep93xx_pcm_dma_params *params;
int pointer_bytes;
- struct tasklet_struct period_tasklet;
int periods;
- struct ep93xx_dma_buffer buf[32];
+ int period_bytes;
+ struct dma_chan *dma_chan;
+ struct ep93xx_dma_data dma_data;
};
-static void ep93xx_pcm_period_elapsed(unsigned long data)
+static void ep93xx_pcm_dma_callback(void *data)
{
- struct snd_pcm_substream *substream = (struct snd_pcm_substream *)data;
+ struct snd_pcm_substream *substream = data;
+ struct ep93xx_runtime_data *rtd = substream->runtime->private_data;
+
+ rtd->pointer_bytes += rtd->period_bytes;
+ rtd->pointer_bytes %= rtd->period_bytes * rtd->periods;
+
snd_pcm_period_elapsed(substream);
}
-static void ep93xx_pcm_buffer_started(void *cookie,
- struct ep93xx_dma_buffer *buf)
+static bool ep93xx_pcm_dma_filter(struct dma_chan *chan, void *filter_param)
{
-}
+ struct ep93xx_dma_data *data = filter_param;
-static void ep93xx_pcm_buffer_finished(void *cookie,
- struct ep93xx_dma_buffer *buf,
- int bytes, int error)
-{
- struct snd_pcm_substream *substream = cookie;
- struct ep93xx_runtime_data *rtd = substream->runtime->private_data;
-
- if (buf == rtd->buf + rtd->periods - 1)
- rtd->pointer_bytes = 0;
- else
- rtd->pointer_bytes += buf->size;
-
- if (!error) {
- ep93xx_dma_m2p_submit_recursive(&rtd->cl, buf);
- tasklet_schedule(&rtd->period_tasklet);
- } else {
- snd_pcm_stop(substream, SNDRV_PCM_STATE_XRUN);
+ if (data->direction == ep93xx_dma_chan_direction(chan)) {
+ chan->private = data;
+ return true;
}
+
+ return false;
}
static int ep93xx_pcm_open(struct snd_pcm_substream *substream)
@@ -98,30 +90,38 @@
struct snd_soc_dai *cpu_dai = soc_rtd->cpu_dai;
struct ep93xx_pcm_dma_params *dma_params;
struct ep93xx_runtime_data *rtd;
+ dma_cap_mask_t mask;
int ret;
- dma_params = snd_soc_dai_get_dma_data(cpu_dai, substream);
+ ret = snd_pcm_hw_constraint_integer(substream->runtime,
+ SNDRV_PCM_HW_PARAM_PERIODS);
+ if (ret < 0)
+ return ret;
+
snd_soc_set_runtime_hwparams(substream, &ep93xx_pcm_hardware);
rtd = kmalloc(sizeof(*rtd), GFP_KERNEL);
if (!rtd)
return -ENOMEM;
- memset(&rtd->period_tasklet, 0, sizeof(rtd->period_tasklet));
- rtd->period_tasklet.func = ep93xx_pcm_period_elapsed;
- rtd->period_tasklet.data = (unsigned long)substream;
+ dma_cap_zero(mask);
+ dma_cap_set(DMA_SLAVE, mask);
+ dma_cap_set(DMA_CYCLIC, mask);
- rtd->cl.name = dma_params->name;
- rtd->cl.flags = dma_params->dma_port | EP93XX_DMA_M2P_IGNORE_ERROR |
- ((substream->stream == SNDRV_PCM_STREAM_PLAYBACK) ?
- EP93XX_DMA_M2P_TX : EP93XX_DMA_M2P_RX);
- rtd->cl.cookie = substream;
- rtd->cl.buffer_started = ep93xx_pcm_buffer_started;
- rtd->cl.buffer_finished = ep93xx_pcm_buffer_finished;
- ret = ep93xx_dma_m2p_client_register(&rtd->cl);
- if (ret < 0) {
+ dma_params = snd_soc_dai_get_dma_data(cpu_dai, substream);
+ rtd->dma_data.port = dma_params->dma_port;
+ rtd->dma_data.name = dma_params->name;
+
+ if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
+ rtd->dma_data.direction = DMA_TO_DEVICE;
+ else
+ rtd->dma_data.direction = DMA_FROM_DEVICE;
+
+ rtd->dma_chan = dma_request_channel(mask, ep93xx_pcm_dma_filter,
+ &rtd->dma_data);
+ if (!rtd->dma_chan) {
kfree(rtd);
- return ret;
+ return -EINVAL;
}
substream->runtime->private_data = rtd;
@@ -132,31 +132,52 @@
{
struct ep93xx_runtime_data *rtd = substream->runtime->private_data;
- ep93xx_dma_m2p_client_unregister(&rtd->cl);
+ dma_release_channel(rtd->dma_chan);
kfree(rtd);
return 0;
}
+static int ep93xx_pcm_dma_submit(struct snd_pcm_substream *substream)
+{
+ struct snd_pcm_runtime *runtime = substream->runtime;
+ struct ep93xx_runtime_data *rtd = runtime->private_data;
+ struct dma_chan *chan = rtd->dma_chan;
+ struct dma_device *dma_dev = chan->device;
+ struct dma_async_tx_descriptor *desc;
+
+ rtd->pointer_bytes = 0;
+ desc = dma_dev->device_prep_dma_cyclic(chan, runtime->dma_addr,
+ rtd->period_bytes * rtd->periods,
+ rtd->period_bytes,
+ rtd->dma_data.direction);
+ if (!desc)
+ return -EINVAL;
+
+ desc->callback = ep93xx_pcm_dma_callback;
+ desc->callback_param = substream;
+
+ dmaengine_submit(desc);
+ return 0;
+}
+
+static void ep93xx_pcm_dma_flush(struct snd_pcm_substream *substream)
+{
+ struct snd_pcm_runtime *runtime = substream->runtime;
+ struct ep93xx_runtime_data *rtd = runtime->private_data;
+
+ dmaengine_terminate_all(rtd->dma_chan);
+}
+
static int ep93xx_pcm_hw_params(struct snd_pcm_substream *substream,
struct snd_pcm_hw_params *params)
{
struct snd_pcm_runtime *runtime = substream->runtime;
struct ep93xx_runtime_data *rtd = runtime->private_data;
- size_t totsize = params_buffer_bytes(params);
- size_t period = params_period_bytes(params);
- int i;
snd_pcm_set_runtime_buffer(substream, &substream->dma_buffer);
- runtime->dma_bytes = totsize;
- rtd->periods = (totsize + period - 1) / period;
- for (i = 0; i < rtd->periods; i++) {
- rtd->buf[i].bus_addr = runtime->dma_addr + (i * period);
- rtd->buf[i].size = period;
- if ((i + 1) * period > totsize)
- rtd->buf[i].size = totsize - (i * period);
- }
-
+ rtd->periods = params_periods(params);
+ rtd->period_bytes = params_period_bytes(params);
return 0;
}
@@ -168,24 +189,20 @@
static int ep93xx_pcm_trigger(struct snd_pcm_substream *substream, int cmd)
{
- struct ep93xx_runtime_data *rtd = substream->runtime->private_data;
int ret;
- int i;
ret = 0;
switch (cmd) {
case SNDRV_PCM_TRIGGER_START:
case SNDRV_PCM_TRIGGER_RESUME:
case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
- rtd->pointer_bytes = 0;
- for (i = 0; i < rtd->periods; i++)
- ep93xx_dma_m2p_submit(&rtd->cl, rtd->buf + i);
+ ret = ep93xx_pcm_dma_submit(substream);
break;
case SNDRV_PCM_TRIGGER_STOP:
case SNDRV_PCM_TRIGGER_SUSPEND:
case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
- ep93xx_dma_m2p_flush(&rtd->cl);
+ ep93xx_pcm_dma_flush(substream);
break;
default: