mac80211: move VHT related RX_FLAG to another variable
ieee80211_rx_status.flags is full. Define a new vht_flag
variable to be able to set more VHT related flags and make
room in flags.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath10k]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
diff --git a/include/net/mac80211.h b/include/net/mac80211.h
index 452eb59..a119da5 100644
--- a/include/net/mac80211.h
+++ b/include/net/mac80211.h
@@ -808,9 +808,6 @@
* @RX_FLAG_HT: HT MCS was used and rate_idx is MCS index
* @RX_FLAG_VHT: VHT MCS was used and rate_index is MCS index
* @RX_FLAG_40MHZ: HT40 (40 MHz) was used
- * @RX_FLAG_80MHZ: 80 MHz was used
- * @RX_FLAG_80P80MHZ: 80+80 MHz was used
- * @RX_FLAG_160MHZ: 160 MHz was used
* @RX_FLAG_SHORT_GI: Short guard interval was used
* @RX_FLAG_NO_SIGNAL_VAL: The signal strength value is not present.
* Valid only for data frames (mainly A-MPDU)
@@ -866,9 +863,6 @@
RX_FLAG_AMPDU_DELIM_CRC_KNOWN = BIT(20),
RX_FLAG_MACTIME_END = BIT(21),
RX_FLAG_VHT = BIT(22),
- RX_FLAG_80MHZ = BIT(23),
- RX_FLAG_80P80MHZ = BIT(24),
- RX_FLAG_160MHZ = BIT(25),
RX_FLAG_STBC_MASK = BIT(26) | BIT(27),
RX_FLAG_10MHZ = BIT(28),
RX_FLAG_5MHZ = BIT(29),
@@ -878,6 +872,21 @@
#define RX_FLAG_STBC_SHIFT 26
/**
+ * enum mac80211_rx_vht_flags - receive VHT flags
+ *
+ * These flags are used with the @vht_flag member of
+ * &struct ieee80211_rx_status.
+ * @RX_VHT_FLAG_80MHZ: 80 MHz was used
+ * @RX_VHT_FLAG_80P80MHZ: 80+80 MHz was used
+ * @RX_VHT_FLAG_160MHZ: 160 MHz was used
+ */
+enum mac80211_rx_vht_flags {
+ RX_VHT_FLAG_80MHZ = BIT(0),
+ RX_VHT_FLAG_80P80MHZ = BIT(1),
+ RX_VHT_FLAG_160MHZ = BIT(2),
+};
+
+/**
* struct ieee80211_rx_status - receive status
*
* The low-level driver should provide this information (the subset
@@ -902,6 +911,7 @@
* HT or VHT is used (%RX_FLAG_HT/%RX_FLAG_VHT)
* @vht_nss: number of streams (VHT only)
* @flag: %RX_FLAG_*
+ * @vht_flag: %RX_VHT_FLAG_*
* @rx_flags: internal RX flags for mac80211
* @ampdu_reference: A-MPDU reference number, must be a different value for
* each A-MPDU but the same for each subframe within one A-MPDU
@@ -913,6 +923,7 @@
u32 ampdu_reference;
u32 flag;
u16 freq;
+ u8 vht_flag;
u8 rate_idx;
u8 vht_nss;
u8 rx_flags;