Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/Documentation/scsi/aic79xx.txt b/Documentation/scsi/aic79xx.txt
new file mode 100644
index 0000000..0aeef74
--- /dev/null
+++ b/Documentation/scsi/aic79xx.txt
@@ -0,0 +1,516 @@
+====================================================================
+= Adaptec Ultra320 Family Manager Set v1.3.11 =
+= =
+= README for =
+= The Linux Operating System =
+====================================================================
+
+The following information is available in this file:
+
+ 1. Supported Hardware
+ 2. Version History
+ 3. Command Line Options
+ 4. Additional Notes
+ 5. Contacting Adaptec
+
+
+1. Supported Hardware
+
+ The following Adaptec SCSI Host Adapters are supported by this
+ driver set.
+
+ Ultra320 ASIC Description
+ ----------------------------------------------------------------
+ AIC-7901A Single Channel 64-bit PCI-X 133MHz to
+ Ultra320 SCSI ASIC
+ AIC-7901B Single Channel 64-bit PCI-X 133MHz to
+ Ultra320 SCSI ASIC with Retained Training
+ AIC-7902A4 Dual Channel 64-bit PCI-X 133MHz to
+ Ultra320 SCSI ASIC
+ AIC-7902B Dual Channel 64-bit PCI-X 133MHz to
+ Ultra320 SCSI ASIC with Retained Training
+
+ Ultra320 Adapters Description ASIC
+ --------------------------------------------------------------------------
+ Adaptec SCSI Card 39320 Dual Channel 64-bit PCI-X 133MHz to 7902A4/7902B
+ Ultra320 SCSI Card (one external
+ 68-pin, two internal 68-pin)
+ Adaptec SCSI Card 39320A Dual Channel 64-bit PCI-X 133MHz to 7902B
+ Ultra320 SCSI Card (one external
+ 68-pin, two internal 68-pin)
+ Adaptec SCSI Card 39320D Dual Channel 64-bit PCI-X 133MHz to 7902A4
+ Ultra320 SCSI Card (two external VHDC
+ and one internal 68-pin)
+ Adaptec SCSI Card 39320D Dual Channel 64-bit PCI-X 133MHz to 7902A4
+ Ultra320 SCSI Card (two external VHDC
+ and one internal 68-pin) based on the
+ AIC-7902B ASIC
+ Adaptec SCSI Card 29320 Single Channel 64-bit PCI-X 133MHz to 7901A
+ Ultra320 SCSI Card (one external
+ 68-pin, two internal 68-pin, one
+ internal 50-pin)
+ Adaptec SCSI Card 29320A Single Channel 64-bit PCI-X 133MHz to 7901B
+ Ultra320 SCSI Card (one external
+ 68-pin, two internal 68-pin, one
+ internal 50-pin)
+ Adaptec SCSI Card 29320LP Single Channel 64-bit Low Profile 7901A
+ PCI-X 133MHz to Ultra320 SCSI Card
+ (One external VHDC, one internal
+ 68-pin)
+ Adaptec SCSI Card 29320ALP Single Channel 64-bit Low Profile 7901B
+ PCI-X 133MHz to Ultra320 SCSI Card
+ (One external VHDC, one internal
+ 68-pin)
+2. Version History
+
+ 1.3.11 (July 11, 2003)
+ - Fix several deadlock issues.
+ - Add 29320ALP and 39320B Id's.
+
+ 1.3.10 (June 3rd, 2003)
+ - Align the SCB_TAG field on a 16byte boundary. This avoids
+ SCB corruption on some PCI-33 busses.
+ - Correct non-zero luns on Rev B. hardware.
+ - Update for change in 2.5.X SCSI proc FS interface.
+ - When negotiation async via an 8bit WDTR message, send
+ an SDTR with an offset of 0 to be sure the target
+ knows we are async. This works around a firmware defect
+ in the Quantum Atlas 10K.
+ - Implement controller susupend and resume.
+ - Clear PCI error state during driver attach so that we
+ don't disable memory mapped I/O due to a stray write
+ by some other driver probe that occurred before we
+ claimed the controller.
+
+ 1.3.9 (May 22nd, 2003)
+ - Fix compiler errors.
+ - Remove S/G splitting for segments that cross a 4GB boundary.
+ This is guaranteed not to happen in Linux.
+ - Add support for scsi_report_device_reset() found in
+ 2.5.X kernels.
+ - Add 7901B support.
+ - Simplify handling of the packtized lun Rev A workaround.
+ - Correct and simplify handling of the ignore wide residue
+ message. The previous code would fail to report a residual
+ if the transaction data length was even and we received
+ an IWR message.
+
+ 1.3.8 (April 29th, 2003)
+ - Fix types accessed via the command line interface code.
+ - Perform a few firmware optimizations.
+ - Fix "Unexpected PKT busfree" errors.
+ - Use a sequencer interrupt to notify the host of
+ commands with bad status. We defer the notification
+ until there are no outstanding selections to ensure
+ that the host is interrupted for as short a time as
+ possible.
+ - Remove pre-2.2.X support.
+ - Add support for new 2.5.X interrupt API.
+ - Correct big-endian architecture support.
+
+ 1.3.7 (April 16th, 2003)
+ - Use del_timer_sync() to ensure that no timeouts
+ are pending during controller shutdown.
+ - For pre-2.5.X kernels, carefully adjust our segment
+ list size to avoid SCSI malloc pool fragmentation.
+ - Cleanup channel display in our /proc output.
+ - Workaround duplicate device entries in the mid-layer
+ devlice list during add-single-device.
+
+ 1.3.6 (March 28th, 2003)
+ - Correct a double free in the Domain Validation code.
+ - Correct a reference to free'ed memory during controller
+ shutdown.
+ - Reset the bus on an SE->LVD change. This is required
+ to reset our transcievers.
+
+ 1.3.5 (March 24th, 2003)
+ - Fix a few register window mode bugs.
+ - Include read streaming in the PPR flags we display in
+ diagnostics as well as /proc.
+ - Add PCI hot plug support for 2.5.X kernels.
+ - Correct default precompensation value for RevA hardware.
+ - Fix Domain Validation thread shutdown.
+ - Add a firmware workaround to make the LED blink
+ brighter during packetized operations on the H2A4.
+ - Correct /proc display of user read streaming settings.
+ - Simplify driver locking by releasing the io_request_lock
+ upon driver entry from the mid-layer.
+ - Cleanup command line parsing and move much of this code
+ to aiclib.
+
+ 1.3.4 (February 28th, 2003)
+ - Correct a race condition in our error recovery handler.
+ - Allow Test Unit Ready commands to take a full 5 seconds
+ during Domain Validation.
+
+ 1.3.2 (February 19th, 2003)
+ - Correct a Rev B. regression due to the GEM318
+ compatibility fix included in 1.3.1.
+
+ 1.3.1 (February 11th, 2003)
+ - Add support for the 39320A.
+ - Improve recovery for certain PCI-X errors.
+ - Fix handling of LQ/DATA/LQ/DATA for the
+ same write transaction that can occur without
+ interveining training.
+ - Correct compatibility issues with the GEM318
+ enclosure services device.
+ - Correct data corruption issue that occurred under
+ high tag depth write loads.
+ - Adapt to a change in the 2.5.X daemonize() API.
+ - Correct a "Missing case in ahd_handle_scsiint" panic.
+
+ 1.3.0 (January 21st, 2003)
+ - Full regression testing for all U320 products completed.
+ - Added abort and target/lun reset error recovery handler and
+ interrupt coalessing.
+
+ 1.2.0 (November 14th, 2002)
+ - Added support for Domain Validation
+ - Add support for the Hewlett-Packard version of the 39320D
+ and AIC-7902 adapters.
+ Support for previous adapters has not been fully tested and should
+ only be used at the customer's own risk.
+
+ 1.1.1 (September 24th, 2002)
+ - Added support for the Linux 2.5.X kernel series
+
+ 1.1.0 (September 17th, 2002)
+ - Added support for four additional SCSI products:
+ ASC-39320, ASC-29320, ASC-29320LP, AIC-7901.
+
+ 1.0.0 (May 30th, 2002)
+ - Initial driver release.
+
+ 2.1. Software/Hardware Features
+ - Support for the SPI-4 "Ultra320" standard:
+ - 320MB/s transfer rates
+ - Packetized SCSI Protocol at 160MB/s and 320MB/s
+ - Quick Arbitration Selection (QAS)
+ - Retained Training Information (Rev B. ASIC only)
+ - Interrupt Coalessing
+ - Initiator Mode (target mode not currently
+ supported)
+ - Support for the PCI-X standard up to 133MHz
+ - Support for the PCI v2.2 standard
+ - Domain Validation
+
+ 2.2. Operating System Support:
+ - Redhat Linux 7.2, 7.3, 8.0, Advanced Server 2.1
+ - SuSE Linux 7.3, 8.0, 8.1, Enterprise Server 7
+ - only Intel and AMD x86 supported at this time
+ - >4GB memory configurations supported.
+
+ Refer to the User's Guide for more details on this.
+
+3. Command Line Options
+
+ WARNING: ALTERING OR ADDING THESE DRIVER PARAMETERS
+ INCORRECTLY CAN RENDER YOUR SYSTEM INOPERABLE.
+ USE THEM WITH CAUTION.
+
+ Edit the file "modprobe.conf" in the directory /etc and add/edit a
+ line containing 'options aic79xx aic79xx=[command[,command...]]' where
+ 'command' is one or more of the following:
+ -----------------------------------------------------------------
+ Option: verbose
+ Definition: enable additional informative messages during
+ driver operation.
+ Possible Values: This option is a flag
+ Default Value: disabled
+ -----------------------------------------------------------------
+ Option: debug:[value]
+ Definition: Enables various levels of debugging information
+ The bit definitions for the debugging mask can
+ be found in drivers/scsi/aic7xxx/aic79xx.h under
+ the "Debug" heading.
+ Possible Values: 0x0000 = no debugging, 0xffff = full debugging
+ Default Value: 0x0000
+ -----------------------------------------------------------------
+ Option: no_reset
+ Definition: Do not reset the bus during the initial probe
+ phase
+ Possible Values: This option is a flag
+ Default Value: disabled
+ -----------------------------------------------------------------
+ Option: extended
+ Definition: Force extended translation on the controller
+ Possible Values: This option is a flag
+ Default Value: disabled
+ -----------------------------------------------------------------
+ Option: periodic_otag
+ Definition: Send an ordered tag periodically to prevent
+ tag starvation. Needed for some older devices
+ Possible Values: This option is a flag
+ Default Value: disabled
+ -----------------------------------------------------------------
+ Option: reverse_scan
+ Definition: Probe the scsi bus in reverse order, starting
+ with target 15
+ Possible Values: This option is a flag
+ Default Value: disabled
+ -----------------------------------------------------------------
+ Option: global_tag_depth
+ Definition: Global tag depth for all targets on all busses.
+ This option sets the default tag depth which
+ may be selectively overridden vi the tag_info
+ option.
+ Possible Values: 1 - 253
+ Default Value: 32
+ -----------------------------------------------------------------
+ Option: tag_info:{{value[,value...]}[,{value[,value...]}...]}
+ Definition: Set the per-target tagged queue depth on a
+ per controller basis. Both controllers and targets
+ may be ommitted indicating that they should retain
+ the default tag depth.
+ Examples: tag_info:{{16,32,32,64,8,8,,32,32,32,32,32,32,32,32,32}
+ On Controller 0
+ specifies a tag depth of 16 for target 0
+ specifies a tag depth of 64 for target 3
+ specifies a tag depth of 8 for targets 4 and 5
+ leaves target 6 at the default
+ specifies a tag depth of 32 for targets 1,2,7-15
+ All other targets retain the default depth.
+
+ tag_info:{{},{32,,32}}
+ On Controller 1
+ specifies a tag depth of 32 for targets 0 and 2
+ All other targets retain the default depth.
+
+ Possible Values: 1 - 253
+ Default Value: 32
+ -----------------------------------------------------------------
+ Option: rd_strm: {rd_strm_bitmask[,rd_strm_bitmask...]}
+ Definition: Enable read streaming on a per target basis.
+ The rd_strm_bitmask is a 16 bit hex value in which
+ each bit represents a target. Setting the target's
+ bit to '1' enables read streaming for that
+ target. Controllers may be ommitted indicating that
+ they should retain the default read streaming setting.
+ Example: rd_strm:{0x0041}
+ On Controller 0
+ enables read streaming for targets 0 and 6.
+ disables read streaming for targets 1-5,7-15.
+ All other targets retain the default read
+ streaming setting.
+ Example: rd_strm:{0x0023,,0xFFFF}
+ On Controller 0
+ enables read streaming for targets 1,2, and 5.
+ disables read streaming for targets 3,4,6-15.
+ On Controller 2
+ enables read streaming for all targets.
+ All other targets retain the default read
+ streaming setting.
+
+ Possible Values: 0x0000 - 0xffff
+ Default Value: 0x0000
+ -----------------------------------------------------------------
+ Option: dv: {value[,value...]}
+ Definition: Set Domain Validation Policy on a per-controller basis.
+ Controllers may be ommitted indicating that
+ they should retain the default read streaming setting.
+ Example: dv:{-1,0,,1,1,0}
+ On Controller 0 leave DV at its default setting.
+ On Controller 1 disable DV.
+ Skip configuration on Controller 2.
+ On Controllers 3 and 4 enable DV.
+ On Controller 5 disable DV.
+
+ Possible Values: < 0 Use setting from serial EEPROM.
+ 0 Disable DV
+ > 0 Enable DV
+ Default Value: DV Serial EEPROM configuration setting.
+ -----------------------------------------------------------------
+ Option: seltime:[value]
+ Definition: Specifies the selection timeout value
+ Possible Values: 0 = 256ms, 1 = 128ms, 2 = 64ms, 3 = 32ms
+ Default Value: 0
+ -----------------------------------------------------------------
+
+ *** The following three options should only be changed at ***
+ *** the direction of a technical support representative. ***
+
+ -----------------------------------------------------------------
+ Option: precomp: {value[,value...]}
+ Definition: Set IO Cell precompensation value on a per-controller
+ basis.
+ Controllers may be ommitted indicating that
+ they should retain the default precompensation setting.
+ Example: precomp:{0x1}
+ On Controller 0 set precompensation to 1.
+ Example: precomp:{1,,7}
+ On Controller 0 set precompensation to 1.
+ On Controller 2 set precompensation to 8.
+
+ Possible Values: 0 - 7
+ Default Value: Varies based on chip revision
+ -----------------------------------------------------------------
+ Option: slewrate: {value[,value...]}
+ Definition: Set IO Cell slew rate on a per-controller basis.
+ Controllers may be ommitted indicating that
+ they should retain the default slew rate setting.
+ Example: slewrate:{0x1}
+ On Controller 0 set slew rate to 1.
+ Example: slewrate :{1,,8}
+ On Controller 0 set slew rate to 1.
+ On Controller 2 set slew rate to 8.
+
+ Possible Values: 0 - 15
+ Default Value: Varies based on chip revision
+ -----------------------------------------------------------------
+ Option: amplitude: {value[,value...]}
+ Definition: Set IO Cell signal amplitude on a per-controller basis.
+ Controllers may be ommitted indicating that
+ they should retain the default read streaming setting.
+ Example: amplitude:{0x1}
+ On Controller 0 set amplitude to 1.
+ Example: amplitude :{1,,7}
+ On Controller 0 set amplitude to 1.
+ On Controller 2 set amplitude to 7.
+
+ Possible Values: 1 - 7
+ Default Value: Varies based on chip revision
+ -----------------------------------------------------------------
+
+ Example: 'options aic79xx aic79xx=verbose,rd_strm:{{0x0041}}'
+ enables verbose output in the driver and turns read streaming on
+ for targets 0 and 6 of Controller 0.
+
+4. Additional Notes
+
+ 4.1. Known/Unresolved or FYI Issues
+
+ * Under SuSE Linux Enterprise 7, the driver may fail to operate
+ correctly due to a problem with PCI interrupt routing in the
+ Linux kernel. Please contact SuSE for an updated Linux
+ kernel.
+
+ 4.2. Third-Party Compatibility Issues
+
+ * Adaptec only supports Ultra320 hard drives running
+ the latest firmware available. Please check with
+ your hard drive manufacturer to ensure you have the
+ latest version.
+
+ 4.3. Operating System or Technology Limitations
+
+ * PCI Hot Plug is untested and may cause the operating system
+ to stop responding.
+ * Luns that are not numbered contiguously starting with 0 might not
+ be automatically probed during system startup. This is a limitation
+ of the OS. Please contact your Linux vendor for instructions on
+ manually probing non-contiguous luns.
+ * Using the Driver Update Disk version of this package during OS
+ installation under RedHat might result in two versions of this
+ driver being installed into the system module directory. This
+ might cause problems with the /sbin/mkinitrd program and/or
+ other RPM packages that try to install system modules. The best
+ way to correct this once the system is running is to install
+ the latest RPM package version of this driver, available from
+ http://www.adaptec.com.
+
+
+5. Contacting Adaptec
+
+ A Technical Support Identification (TSID) Number is required for
+ Adaptec technical support.
+ - The 12-digit TSID can be found on the white barcode-type label
+ included inside the box with your product. The TSID helps us
+ provide more efficient service by accurately identifying your
+ product and support status.
+ Support Options
+ - Search the Adaptec Support Knowledgebase (ASK) at
+ http://ask.adaptec.com for articles, troubleshooting tips, and
+ frequently asked questions for your product.
+ - For support via Email, submit your question to Adaptec's
+ Technical Support Specialists at http://ask.adaptec.com.
+
+ North America
+ - Visit our Web site at http://www.adaptec.com.
+ - To speak with a Fibre Channel/RAID/External Storage Technical
+ Support Specialist, call 1-321-207-2000,
+ Hours: Monday-Friday, 3:00 A.M. to 5:00 P.M., PST.
+ (Not open on holidays)
+ - For Technical Support in all other technologies including
+ SCSI, call 1-408-934-7274,
+ Hours: Monday-Friday, 6:00 A.M. to 5:00 P.M., PST.
+ (Not open on holidays)
+ - For after hours support, call 1-800-416-8066 ($99/call,
+ $149/call on holidays)
+ - To order Adaptec products including software and cables, call
+ 1-800-442-7274 or 1-408-957-7274. You can also visit our
+ online store at http://www.adaptecstore.com
+
+ Europe
+ - Visit our Web site at http://www.adaptec-europe.com.
+ - English and French: To speak with a Technical Support
+ Specialist, call one of the following numbers:
+ - English: +32-2-352-3470
+ - French: +32-2-352-3460
+ Hours: Monday-Thursday, 10:00 to 12:30, 13:30 to 17:30 CET
+ Friday, 10:00 to 12:30, 13:30 to 16:30 CET
+ - German: To speak with a Technical Support Specialist,
+ call +49-89-456-40660
+ Hours: Monday-Thursday, 09:30 to 12:30, 13:30 to 16:30 CET
+ Friday, 09:30 to 12:30, 13:30 to 15:00 CET
+ - To order Adaptec products, including accessories and cables:
+ - UK: +0800-96-65-26 or fax +0800-731-02-95
+ - Other European countries: +32-11-300-379
+
+ Australia and New Zealand
+ - Visit our Web site at http://www.adaptec.com.au.
+ - To speak with a Technical Support Specialist, call
+ +612-9416-0698
+ Hours: Monday-Friday, 10:00 A.M. to 4:30 P.M., EAT
+ (Not open on holidays)
+
+ Japan
+ - To speak with a Technical Support Specialist, call
+ +81-3-5308-6120
+ Hours: Monday-Friday, 9:00 a.m. to 12:00 p.m., 1:00 p.m. to
+ 6:00 p.m. TSC
+
+ Hong Kong and China
+ - To speak with a Technical Support Specialist, call
+ +852-2869-7200
+ Hours: Monday-Friday, 10:00 to 17:00.
+ - Fax Technical Support at +852-2869-7100.
+
+ Singapore
+ - To speak with a Technical Support Specialist, call
+ +65-245-7470
+ Hours: Monday-Friday, 10:00 to 17:00.
+ - Fax Technical Support at +852-2869-7100
+
+-------------------------------------------------------------------
+/*
+ * Copyright (c) 2003 Adaptec Inc. 691 S. Milpitas Blvd., Milpitas CA 95035 USA.
+ * All rights reserved.
+ *
+ * You are permitted to redistribute, use and modify this README file in whole
+ * or in part in conjunction with redistribution of software governed by the
+ * General Public License, provided that the following conditions are met:
+ * 1. Redistributions of README file must retain the above copyright
+ * notice, this list of conditions, and the following disclaimer,
+ * without modification.
+ * 2. The name of the author may not be used to endorse or promote products
+ * derived from this software without specific prior written permission.
+ * 3. Modifications or new contributions must be attributed in a copyright
+ * notice identifying the author ("Contributor") and added below the
+ * original copyright notice. The copyright notice is for purposes of
+ * identifying contributors and should not be deemed as permission to alter
+ * the permissions given by Adaptec.
+ *
+ * THIS README FILE IS PROVIDED BY ADAPTEC AND CONTRIBUTORS ``AS IS'' AND
+ * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY
+ * WARRANTIES OF NON-INFRINGEMENT OR THE IMPLIED WARRANTIES OF MERCHANTABILITY
+ * AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
+ * ADAPTEC OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
+ * TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
+ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
+ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
+ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS README
+ * FILE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */