Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/drivers/net/wireless/wavelan.c b/drivers/net/wireless/wavelan.c
new file mode 100644
index 0000000..7a5e20a
--- /dev/null
+++ b/drivers/net/wireless/wavelan.c
@@ -0,0 +1,4452 @@
+/*
+ * WaveLAN ISA driver
+ *
+ * Jean II - HPLB '96
+ *
+ * Reorganisation and extension of the driver.
+ * Original copyright follows (also see the end of this file).
+ * See wavelan.p.h for details.
+ *
+ *
+ *
+ * AT&T GIS (nee NCR) WaveLAN card:
+ * An Ethernet-like radio transceiver
+ * controlled by an Intel 82586 coprocessor.
+ */
+
+#include "wavelan.p.h" /* Private header */
+
+/************************* MISC SUBROUTINES **************************/
+/*
+ * Subroutines which won't fit in one of the following category
+ * (WaveLAN modem or i82586)
+ */
+
+/*------------------------------------------------------------------*/
+/*
+ * Translate irq number to PSA irq parameter
+ */
+static u8 wv_irq_to_psa(int irq)
+{
+ if (irq < 0 || irq >= NELS(irqvals))
+ return 0;
+
+ return irqvals[irq];
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Translate PSA irq parameter to irq number
+ */
+static int __init wv_psa_to_irq(u8 irqval)
+{
+ int irq;
+
+ for (irq = 0; irq < NELS(irqvals); irq++)
+ if (irqvals[irq] == irqval)
+ return irq;
+
+ return -1;
+}
+
+#ifdef STRUCT_CHECK
+/*------------------------------------------------------------------*/
+/*
+ * Sanity routine to verify the sizes of the various WaveLAN interface
+ * structures.
+ */
+static char *wv_struct_check(void)
+{
+#define SC(t,s,n) if (sizeof(t) != s) return(n);
+
+ SC(psa_t, PSA_SIZE, "psa_t");
+ SC(mmw_t, MMW_SIZE, "mmw_t");
+ SC(mmr_t, MMR_SIZE, "mmr_t");
+ SC(ha_t, HA_SIZE, "ha_t");
+
+#undef SC
+
+ return ((char *) NULL);
+} /* wv_struct_check */
+#endif /* STRUCT_CHECK */
+
+/********************* HOST ADAPTER SUBROUTINES *********************/
+/*
+ * Useful subroutines to manage the WaveLAN ISA interface
+ *
+ * One major difference with the PCMCIA hardware (except the port mapping)
+ * is that we have to keep the state of the Host Control Register
+ * because of the interrupt enable & bus size flags.
+ */
+
+/*------------------------------------------------------------------*/
+/*
+ * Read from card's Host Adaptor Status Register.
+ */
+static inline u16 hasr_read(unsigned long ioaddr)
+{
+ return (inw(HASR(ioaddr)));
+} /* hasr_read */
+
+/*------------------------------------------------------------------*/
+/*
+ * Write to card's Host Adapter Command Register.
+ */
+static inline void hacr_write(unsigned long ioaddr, u16 hacr)
+{
+ outw(hacr, HACR(ioaddr));
+} /* hacr_write */
+
+/*------------------------------------------------------------------*/
+/*
+ * Write to card's Host Adapter Command Register. Include a delay for
+ * those times when it is needed.
+ */
+static inline void hacr_write_slow(unsigned long ioaddr, u16 hacr)
+{
+ hacr_write(ioaddr, hacr);
+ /* delay might only be needed sometimes */
+ mdelay(1);
+} /* hacr_write_slow */
+
+/*------------------------------------------------------------------*/
+/*
+ * Set the channel attention bit.
+ */
+static inline void set_chan_attn(unsigned long ioaddr, u16 hacr)
+{
+ hacr_write(ioaddr, hacr | HACR_CA);
+} /* set_chan_attn */
+
+/*------------------------------------------------------------------*/
+/*
+ * Reset, and then set host adaptor into default mode.
+ */
+static inline void wv_hacr_reset(unsigned long ioaddr)
+{
+ hacr_write_slow(ioaddr, HACR_RESET);
+ hacr_write(ioaddr, HACR_DEFAULT);
+} /* wv_hacr_reset */
+
+/*------------------------------------------------------------------*/
+/*
+ * Set the I/O transfer over the ISA bus to 8-bit mode
+ */
+static inline void wv_16_off(unsigned long ioaddr, u16 hacr)
+{
+ hacr &= ~HACR_16BITS;
+ hacr_write(ioaddr, hacr);
+} /* wv_16_off */
+
+/*------------------------------------------------------------------*/
+/*
+ * Set the I/O transfer over the ISA bus to 8-bit mode
+ */
+static inline void wv_16_on(unsigned long ioaddr, u16 hacr)
+{
+ hacr |= HACR_16BITS;
+ hacr_write(ioaddr, hacr);
+} /* wv_16_on */
+
+/*------------------------------------------------------------------*/
+/*
+ * Disable interrupts on the WaveLAN hardware.
+ * (called by wv_82586_stop())
+ */
+static inline void wv_ints_off(struct net_device * dev)
+{
+ net_local *lp = (net_local *) dev->priv;
+ unsigned long ioaddr = dev->base_addr;
+
+ lp->hacr &= ~HACR_INTRON;
+ hacr_write(ioaddr, lp->hacr);
+} /* wv_ints_off */
+
+/*------------------------------------------------------------------*/
+/*
+ * Enable interrupts on the WaveLAN hardware.
+ * (called by wv_hw_reset())
+ */
+static inline void wv_ints_on(struct net_device * dev)
+{
+ net_local *lp = (net_local *) dev->priv;
+ unsigned long ioaddr = dev->base_addr;
+
+ lp->hacr |= HACR_INTRON;
+ hacr_write(ioaddr, lp->hacr);
+} /* wv_ints_on */
+
+/******************* MODEM MANAGEMENT SUBROUTINES *******************/
+/*
+ * Useful subroutines to manage the modem of the WaveLAN
+ */
+
+/*------------------------------------------------------------------*/
+/*
+ * Read the Parameter Storage Area from the WaveLAN card's memory
+ */
+/*
+ * Read bytes from the PSA.
+ */
+static void psa_read(unsigned long ioaddr, u16 hacr, int o, /* offset in PSA */
+ u8 * b, /* buffer to fill */
+ int n)
+{ /* size to read */
+ wv_16_off(ioaddr, hacr);
+
+ while (n-- > 0) {
+ outw(o, PIOR2(ioaddr));
+ o++;
+ *b++ = inb(PIOP2(ioaddr));
+ }
+
+ wv_16_on(ioaddr, hacr);
+} /* psa_read */
+
+/*------------------------------------------------------------------*/
+/*
+ * Write the Parameter Storage Area to the WaveLAN card's memory.
+ */
+static void psa_write(unsigned long ioaddr, u16 hacr, int o, /* Offset in PSA */
+ u8 * b, /* Buffer in memory */
+ int n)
+{ /* Length of buffer */
+ int count = 0;
+
+ wv_16_off(ioaddr, hacr);
+
+ while (n-- > 0) {
+ outw(o, PIOR2(ioaddr));
+ o++;
+
+ outb(*b, PIOP2(ioaddr));
+ b++;
+
+ /* Wait for the memory to finish its write cycle */
+ count = 0;
+ while ((count++ < 100) &&
+ (hasr_read(ioaddr) & HASR_PSA_BUSY)) mdelay(1);
+ }
+
+ wv_16_on(ioaddr, hacr);
+} /* psa_write */
+
+#ifdef SET_PSA_CRC
+/*------------------------------------------------------------------*/
+/*
+ * Calculate the PSA CRC
+ * Thanks to Valster, Nico <NVALSTER@wcnd.nl.lucent.com> for the code
+ * NOTE: By specifying a length including the CRC position the
+ * returned value should be zero. (i.e. a correct checksum in the PSA)
+ *
+ * The Windows drivers don't use the CRC, but the AP and the PtP tool
+ * depend on it.
+ */
+static inline u16 psa_crc(u8 * psa, /* The PSA */
+ int size)
+{ /* Number of short for CRC */
+ int byte_cnt; /* Loop on the PSA */
+ u16 crc_bytes = 0; /* Data in the PSA */
+ int bit_cnt; /* Loop on the bits of the short */
+
+ for (byte_cnt = 0; byte_cnt < size; byte_cnt++) {
+ crc_bytes ^= psa[byte_cnt]; /* Its an xor */
+
+ for (bit_cnt = 1; bit_cnt < 9; bit_cnt++) {
+ if (crc_bytes & 0x0001)
+ crc_bytes = (crc_bytes >> 1) ^ 0xA001;
+ else
+ crc_bytes >>= 1;
+ }
+ }
+
+ return crc_bytes;
+} /* psa_crc */
+#endif /* SET_PSA_CRC */
+
+/*------------------------------------------------------------------*/
+/*
+ * update the checksum field in the Wavelan's PSA
+ */
+static void update_psa_checksum(struct net_device * dev, unsigned long ioaddr, u16 hacr)
+{
+#ifdef SET_PSA_CRC
+ psa_t psa;
+ u16 crc;
+
+ /* read the parameter storage area */
+ psa_read(ioaddr, hacr, 0, (unsigned char *) &psa, sizeof(psa));
+
+ /* update the checksum */
+ crc = psa_crc((unsigned char *) &psa,
+ sizeof(psa) - sizeof(psa.psa_crc[0]) -
+ sizeof(psa.psa_crc[1])
+ - sizeof(psa.psa_crc_status));
+
+ psa.psa_crc[0] = crc & 0xFF;
+ psa.psa_crc[1] = (crc & 0xFF00) >> 8;
+
+ /* Write it ! */
+ psa_write(ioaddr, hacr, (char *) &psa.psa_crc - (char *) &psa,
+ (unsigned char *) &psa.psa_crc, 2);
+
+#ifdef DEBUG_IOCTL_INFO
+ printk(KERN_DEBUG "%s: update_psa_checksum(): crc = 0x%02x%02x\n",
+ dev->name, psa.psa_crc[0], psa.psa_crc[1]);
+
+ /* Check again (luxury !) */
+ crc = psa_crc((unsigned char *) &psa,
+ sizeof(psa) - sizeof(psa.psa_crc_status));
+
+ if (crc != 0)
+ printk(KERN_WARNING
+ "%s: update_psa_checksum(): CRC does not agree with PSA data (even after recalculating)\n",
+ dev->name);
+#endif /* DEBUG_IOCTL_INFO */
+#endif /* SET_PSA_CRC */
+} /* update_psa_checksum */
+
+/*------------------------------------------------------------------*/
+/*
+ * Write 1 byte to the MMC.
+ */
+static inline void mmc_out(unsigned long ioaddr, u16 o, u8 d)
+{
+ int count = 0;
+
+ /* Wait for MMC to go idle */
+ while ((count++ < 100) && (inw(HASR(ioaddr)) & HASR_MMC_BUSY))
+ udelay(10);
+
+ outw((u16) (((u16) d << 8) | (o << 1) | 1), MMCR(ioaddr));
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Routine to write bytes to the Modem Management Controller.
+ * We start at the end because it is the way it should be!
+ */
+static inline void mmc_write(unsigned long ioaddr, u8 o, u8 * b, int n)
+{
+ o += n;
+ b += n;
+
+ while (n-- > 0)
+ mmc_out(ioaddr, --o, *(--b));
+} /* mmc_write */
+
+/*------------------------------------------------------------------*/
+/*
+ * Read a byte from the MMC.
+ * Optimised version for 1 byte, avoid using memory.
+ */
+static inline u8 mmc_in(unsigned long ioaddr, u16 o)
+{
+ int count = 0;
+
+ while ((count++ < 100) && (inw(HASR(ioaddr)) & HASR_MMC_BUSY))
+ udelay(10);
+ outw(o << 1, MMCR(ioaddr));
+
+ while ((count++ < 100) && (inw(HASR(ioaddr)) & HASR_MMC_BUSY))
+ udelay(10);
+ return (u8) (inw(MMCR(ioaddr)) >> 8);
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Routine to read bytes from the Modem Management Controller.
+ * The implementation is complicated by a lack of address lines,
+ * which prevents decoding of the low-order bit.
+ * (code has just been moved in the above function)
+ * We start at the end because it is the way it should be!
+ */
+static inline void mmc_read(unsigned long ioaddr, u8 o, u8 * b, int n)
+{
+ o += n;
+ b += n;
+
+ while (n-- > 0)
+ *(--b) = mmc_in(ioaddr, --o);
+} /* mmc_read */
+
+/*------------------------------------------------------------------*/
+/*
+ * Get the type of encryption available.
+ */
+static inline int mmc_encr(unsigned long ioaddr)
+{ /* I/O port of the card */
+ int temp;
+
+ temp = mmc_in(ioaddr, mmroff(0, mmr_des_avail));
+ if ((temp != MMR_DES_AVAIL_DES) && (temp != MMR_DES_AVAIL_AES))
+ return 0;
+ else
+ return temp;
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Wait for the frequency EEPROM to complete a command.
+ * I hope this one will be optimally inlined.
+ */
+static inline void fee_wait(unsigned long ioaddr, /* I/O port of the card */
+ int delay, /* Base delay to wait for */
+ int number)
+{ /* Number of time to wait */
+ int count = 0; /* Wait only a limited time */
+
+ while ((count++ < number) &&
+ (mmc_in(ioaddr, mmroff(0, mmr_fee_status)) &
+ MMR_FEE_STATUS_BUSY)) udelay(delay);
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Read bytes from the Frequency EEPROM (frequency select cards).
+ */
+static void fee_read(unsigned long ioaddr, /* I/O port of the card */
+ u16 o, /* destination offset */
+ u16 * b, /* data buffer */
+ int n)
+{ /* number of registers */
+ b += n; /* Position at the end of the area */
+
+ /* Write the address */
+ mmc_out(ioaddr, mmwoff(0, mmw_fee_addr), o + n - 1);
+
+ /* Loop on all buffer */
+ while (n-- > 0) {
+ /* Write the read command */
+ mmc_out(ioaddr, mmwoff(0, mmw_fee_ctrl),
+ MMW_FEE_CTRL_READ);
+
+ /* Wait until EEPROM is ready (should be quick). */
+ fee_wait(ioaddr, 10, 100);
+
+ /* Read the value. */
+ *--b = ((mmc_in(ioaddr, mmroff(0, mmr_fee_data_h)) << 8) |
+ mmc_in(ioaddr, mmroff(0, mmr_fee_data_l)));
+ }
+}
+
+#ifdef WIRELESS_EXT /* if the wireless extension exists in the kernel */
+
+/*------------------------------------------------------------------*/
+/*
+ * Write bytes from the Frequency EEPROM (frequency select cards).
+ * This is a bit complicated, because the frequency EEPROM has to
+ * be unprotected and the write enabled.
+ * Jean II
+ */
+static void fee_write(unsigned long ioaddr, /* I/O port of the card */
+ u16 o, /* destination offset */
+ u16 * b, /* data buffer */
+ int n)
+{ /* number of registers */
+ b += n; /* Position at the end of the area. */
+
+#ifdef EEPROM_IS_PROTECTED /* disabled */
+#ifdef DOESNT_SEEM_TO_WORK /* disabled */
+ /* Ask to read the protected register */
+ mmc_out(ioaddr, mmwoff(0, mmw_fee_ctrl), MMW_FEE_CTRL_PRREAD);
+
+ fee_wait(ioaddr, 10, 100);
+
+ /* Read the protected register. */
+ printk("Protected 2: %02X-%02X\n",
+ mmc_in(ioaddr, mmroff(0, mmr_fee_data_h)),
+ mmc_in(ioaddr, mmroff(0, mmr_fee_data_l)));
+#endif /* DOESNT_SEEM_TO_WORK */
+
+ /* Enable protected register. */
+ mmc_out(ioaddr, mmwoff(0, mmw_fee_addr), MMW_FEE_ADDR_EN);
+ mmc_out(ioaddr, mmwoff(0, mmw_fee_ctrl), MMW_FEE_CTRL_PREN);
+
+ fee_wait(ioaddr, 10, 100);
+
+ /* Unprotect area. */
+ mmc_out(ioaddr, mmwoff(0, mmw_fee_addr), o + n);
+ mmc_out(ioaddr, mmwoff(0, mmw_fee_ctrl), MMW_FEE_CTRL_PRWRITE);
+#ifdef DOESNT_SEEM_TO_WORK /* disabled */
+ /* or use: */
+ mmc_out(ioaddr, mmwoff(0, mmw_fee_ctrl), MMW_FEE_CTRL_PRCLEAR);
+#endif /* DOESNT_SEEM_TO_WORK */
+
+ fee_wait(ioaddr, 10, 100);
+#endif /* EEPROM_IS_PROTECTED */
+
+ /* Write enable. */
+ mmc_out(ioaddr, mmwoff(0, mmw_fee_addr), MMW_FEE_ADDR_EN);
+ mmc_out(ioaddr, mmwoff(0, mmw_fee_ctrl), MMW_FEE_CTRL_WREN);
+
+ fee_wait(ioaddr, 10, 100);
+
+ /* Write the EEPROM address. */
+ mmc_out(ioaddr, mmwoff(0, mmw_fee_addr), o + n - 1);
+
+ /* Loop on all buffer */
+ while (n-- > 0) {
+ /* Write the value. */
+ mmc_out(ioaddr, mmwoff(0, mmw_fee_data_h), (*--b) >> 8);
+ mmc_out(ioaddr, mmwoff(0, mmw_fee_data_l), *b & 0xFF);
+
+ /* Write the write command. */
+ mmc_out(ioaddr, mmwoff(0, mmw_fee_ctrl),
+ MMW_FEE_CTRL_WRITE);
+
+ /* WaveLAN documentation says to wait at least 10 ms for EEBUSY = 0 */
+ mdelay(10);
+ fee_wait(ioaddr, 10, 100);
+ }
+
+ /* Write disable. */
+ mmc_out(ioaddr, mmwoff(0, mmw_fee_addr), MMW_FEE_ADDR_DS);
+ mmc_out(ioaddr, mmwoff(0, mmw_fee_ctrl), MMW_FEE_CTRL_WDS);
+
+ fee_wait(ioaddr, 10, 100);
+
+#ifdef EEPROM_IS_PROTECTED /* disabled */
+ /* Reprotect EEPROM. */
+ mmc_out(ioaddr, mmwoff(0, mmw_fee_addr), 0x00);
+ mmc_out(ioaddr, mmwoff(0, mmw_fee_ctrl), MMW_FEE_CTRL_PRWRITE);
+
+ fee_wait(ioaddr, 10, 100);
+#endif /* EEPROM_IS_PROTECTED */
+}
+#endif /* WIRELESS_EXT */
+
+/************************ I82586 SUBROUTINES *************************/
+/*
+ * Useful subroutines to manage the Ethernet controller
+ */
+
+/*------------------------------------------------------------------*/
+/*
+ * Read bytes from the on-board RAM.
+ * Why does inlining this function make it fail?
+ */
+static /*inline */ void obram_read(unsigned long ioaddr,
+ u16 o, u8 * b, int n)
+{
+ outw(o, PIOR1(ioaddr));
+ insw(PIOP1(ioaddr), (unsigned short *) b, (n + 1) >> 1);
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Write bytes to the on-board RAM.
+ */
+static inline void obram_write(unsigned long ioaddr, u16 o, u8 * b, int n)
+{
+ outw(o, PIOR1(ioaddr));
+ outsw(PIOP1(ioaddr), (unsigned short *) b, (n + 1) >> 1);
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Acknowledge the reading of the status issued by the i82586.
+ */
+static void wv_ack(struct net_device * dev)
+{
+ net_local *lp = (net_local *) dev->priv;
+ unsigned long ioaddr = dev->base_addr;
+ u16 scb_cs;
+ int i;
+
+ obram_read(ioaddr, scboff(OFFSET_SCB, scb_status),
+ (unsigned char *) &scb_cs, sizeof(scb_cs));
+ scb_cs &= SCB_ST_INT;
+
+ if (scb_cs == 0)
+ return;
+
+ obram_write(ioaddr, scboff(OFFSET_SCB, scb_command),
+ (unsigned char *) &scb_cs, sizeof(scb_cs));
+
+ set_chan_attn(ioaddr, lp->hacr);
+
+ for (i = 1000; i > 0; i--) {
+ obram_read(ioaddr, scboff(OFFSET_SCB, scb_command),
+ (unsigned char *) &scb_cs, sizeof(scb_cs));
+ if (scb_cs == 0)
+ break;
+
+ udelay(10);
+ }
+ udelay(100);
+
+#ifdef DEBUG_CONFIG_ERROR
+ if (i <= 0)
+ printk(KERN_INFO
+ "%s: wv_ack(): board not accepting command.\n",
+ dev->name);
+#endif
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Set channel attention bit and busy wait until command has
+ * completed, then acknowledge completion of the command.
+ */
+static inline int wv_synchronous_cmd(struct net_device * dev, const char *str)
+{
+ net_local *lp = (net_local *) dev->priv;
+ unsigned long ioaddr = dev->base_addr;
+ u16 scb_cmd;
+ ach_t cb;
+ int i;
+
+ scb_cmd = SCB_CMD_CUC & SCB_CMD_CUC_GO;
+ obram_write(ioaddr, scboff(OFFSET_SCB, scb_command),
+ (unsigned char *) &scb_cmd, sizeof(scb_cmd));
+
+ set_chan_attn(ioaddr, lp->hacr);
+
+ for (i = 1000; i > 0; i--) {
+ obram_read(ioaddr, OFFSET_CU, (unsigned char *) &cb,
+ sizeof(cb));
+ if (cb.ac_status & AC_SFLD_C)
+ break;
+
+ udelay(10);
+ }
+ udelay(100);
+
+ if (i <= 0 || !(cb.ac_status & AC_SFLD_OK)) {
+#ifdef DEBUG_CONFIG_ERROR
+ printk(KERN_INFO "%s: %s failed; status = 0x%x\n",
+ dev->name, str, cb.ac_status);
+#endif
+#ifdef DEBUG_I82586_SHOW
+ wv_scb_show(ioaddr);
+#endif
+ return -1;
+ }
+
+ /* Ack the status */
+ wv_ack(dev);
+
+ return 0;
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Configuration commands completion interrupt.
+ * Check if done, and if OK.
+ */
+static inline int
+wv_config_complete(struct net_device * dev, unsigned long ioaddr, net_local * lp)
+{
+ unsigned short mcs_addr;
+ unsigned short status;
+ int ret;
+
+#ifdef DEBUG_INTERRUPT_TRACE
+ printk(KERN_DEBUG "%s: ->wv_config_complete()\n", dev->name);
+#endif
+
+ mcs_addr = lp->tx_first_in_use + sizeof(ac_tx_t) + sizeof(ac_nop_t)
+ + sizeof(tbd_t) + sizeof(ac_cfg_t) + sizeof(ac_ias_t);
+
+ /* Read the status of the last command (set mc list). */
+ obram_read(ioaddr, acoff(mcs_addr, ac_status),
+ (unsigned char *) &status, sizeof(status));
+
+ /* If not completed -> exit */
+ if ((status & AC_SFLD_C) == 0)
+ ret = 0; /* Not ready to be scrapped */
+ else {
+#ifdef DEBUG_CONFIG_ERROR
+ unsigned short cfg_addr;
+ unsigned short ias_addr;
+
+ /* Check mc_config command */
+ if ((status & AC_SFLD_OK) != AC_SFLD_OK)
+ printk(KERN_INFO
+ "%s: wv_config_complete(): set_multicast_address failed; status = 0x%x\n",
+ dev->name, status);
+
+ /* check ia-config command */
+ ias_addr = mcs_addr - sizeof(ac_ias_t);
+ obram_read(ioaddr, acoff(ias_addr, ac_status),
+ (unsigned char *) &status, sizeof(status));
+ if ((status & AC_SFLD_OK) != AC_SFLD_OK)
+ printk(KERN_INFO
+ "%s: wv_config_complete(): set_MAC_address failed; status = 0x%x\n",
+ dev->name, status);
+
+ /* Check config command. */
+ cfg_addr = ias_addr - sizeof(ac_cfg_t);
+ obram_read(ioaddr, acoff(cfg_addr, ac_status),
+ (unsigned char *) &status, sizeof(status));
+ if ((status & AC_SFLD_OK) != AC_SFLD_OK)
+ printk(KERN_INFO
+ "%s: wv_config_complete(): configure failed; status = 0x%x\n",
+ dev->name, status);
+#endif /* DEBUG_CONFIG_ERROR */
+
+ ret = 1; /* Ready to be scrapped */
+ }
+
+#ifdef DEBUG_INTERRUPT_TRACE
+ printk(KERN_DEBUG "%s: <-wv_config_complete() - %d\n", dev->name,
+ ret);
+#endif
+ return ret;
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Command completion interrupt.
+ * Reclaim as many freed tx buffers as we can.
+ * (called in wavelan_interrupt()).
+ * Note : the spinlock is already grabbed for us.
+ */
+static int wv_complete(struct net_device * dev, unsigned long ioaddr, net_local * lp)
+{
+ int nreaped = 0;
+
+#ifdef DEBUG_INTERRUPT_TRACE
+ printk(KERN_DEBUG "%s: ->wv_complete()\n", dev->name);
+#endif
+
+ /* Loop on all the transmit buffers */
+ while (lp->tx_first_in_use != I82586NULL) {
+ unsigned short tx_status;
+
+ /* Read the first transmit buffer */
+ obram_read(ioaddr, acoff(lp->tx_first_in_use, ac_status),
+ (unsigned char *) &tx_status,
+ sizeof(tx_status));
+
+ /* If not completed -> exit */
+ if ((tx_status & AC_SFLD_C) == 0)
+ break;
+
+ /* Hack for reconfiguration */
+ if (tx_status == 0xFFFF)
+ if (!wv_config_complete(dev, ioaddr, lp))
+ break; /* Not completed */
+
+ /* We now remove this buffer */
+ nreaped++;
+ --lp->tx_n_in_use;
+
+/*
+if (lp->tx_n_in_use > 0)
+ printk("%c", "0123456789abcdefghijk"[lp->tx_n_in_use]);
+*/
+
+ /* Was it the last one? */
+ if (lp->tx_n_in_use <= 0)
+ lp->tx_first_in_use = I82586NULL;
+ else {
+ /* Next one in the chain */
+ lp->tx_first_in_use += TXBLOCKZ;
+ if (lp->tx_first_in_use >=
+ OFFSET_CU +
+ NTXBLOCKS * TXBLOCKZ) lp->tx_first_in_use -=
+ NTXBLOCKS * TXBLOCKZ;
+ }
+
+ /* Hack for reconfiguration */
+ if (tx_status == 0xFFFF)
+ continue;
+
+ /* Now, check status of the finished command */
+ if (tx_status & AC_SFLD_OK) {
+ int ncollisions;
+
+ lp->stats.tx_packets++;
+ ncollisions = tx_status & AC_SFLD_MAXCOL;
+ lp->stats.collisions += ncollisions;
+#ifdef DEBUG_TX_INFO
+ if (ncollisions > 0)
+ printk(KERN_DEBUG
+ "%s: wv_complete(): tx completed after %d collisions.\n",
+ dev->name, ncollisions);
+#endif
+ } else {
+ lp->stats.tx_errors++;
+ if (tx_status & AC_SFLD_S10) {
+ lp->stats.tx_carrier_errors++;
+#ifdef DEBUG_TX_FAIL
+ printk(KERN_DEBUG
+ "%s: wv_complete(): tx error: no CS.\n",
+ dev->name);
+#endif
+ }
+ if (tx_status & AC_SFLD_S9) {
+ lp->stats.tx_carrier_errors++;
+#ifdef DEBUG_TX_FAIL
+ printk(KERN_DEBUG
+ "%s: wv_complete(): tx error: lost CTS.\n",
+ dev->name);
+#endif
+ }
+ if (tx_status & AC_SFLD_S8) {
+ lp->stats.tx_fifo_errors++;
+#ifdef DEBUG_TX_FAIL
+ printk(KERN_DEBUG
+ "%s: wv_complete(): tx error: slow DMA.\n",
+ dev->name);
+#endif
+ }
+ if (tx_status & AC_SFLD_S6) {
+ lp->stats.tx_heartbeat_errors++;
+#ifdef DEBUG_TX_FAIL
+ printk(KERN_DEBUG
+ "%s: wv_complete(): tx error: heart beat.\n",
+ dev->name);
+#endif
+ }
+ if (tx_status & AC_SFLD_S5) {
+ lp->stats.tx_aborted_errors++;
+#ifdef DEBUG_TX_FAIL
+ printk(KERN_DEBUG
+ "%s: wv_complete(): tx error: too many collisions.\n",
+ dev->name);
+#endif
+ }
+ }
+
+#ifdef DEBUG_TX_INFO
+ printk(KERN_DEBUG
+ "%s: wv_complete(): tx completed, tx_status 0x%04x\n",
+ dev->name, tx_status);
+#endif
+ }
+
+#ifdef DEBUG_INTERRUPT_INFO
+ if (nreaped > 1)
+ printk(KERN_DEBUG "%s: wv_complete(): reaped %d\n",
+ dev->name, nreaped);
+#endif
+
+ /*
+ * Inform upper layers.
+ */
+ if (lp->tx_n_in_use < NTXBLOCKS - 1) {
+ netif_wake_queue(dev);
+ }
+#ifdef DEBUG_INTERRUPT_TRACE
+ printk(KERN_DEBUG "%s: <-wv_complete()\n", dev->name);
+#endif
+ return nreaped;
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Reconfigure the i82586, or at least ask for it.
+ * Because wv_82586_config uses a transmission buffer, we must do it
+ * when we are sure that there is one left, so we do it now
+ * or in wavelan_packet_xmit() (I can't find any better place,
+ * wavelan_interrupt is not an option), so you may experience
+ * delays sometimes.
+ */
+static inline void wv_82586_reconfig(struct net_device * dev)
+{
+ net_local *lp = (net_local *) dev->priv;
+ unsigned long flags;
+
+ /* Arm the flag, will be cleard in wv_82586_config() */
+ lp->reconfig_82586 = 1;
+
+ /* Check if we can do it now ! */
+ if((netif_running(dev)) && !(netif_queue_stopped(dev))) {
+ spin_lock_irqsave(&lp->spinlock, flags);
+ /* May fail */
+ wv_82586_config(dev);
+ spin_unlock_irqrestore(&lp->spinlock, flags);
+ }
+ else {
+#ifdef DEBUG_CONFIG_INFO
+ printk(KERN_DEBUG
+ "%s: wv_82586_reconfig(): delayed (state = %lX)\n",
+ dev->name, dev->state);
+#endif
+ }
+}
+
+/********************* DEBUG & INFO SUBROUTINES *********************/
+/*
+ * This routine is used in the code to show information for debugging.
+ * Most of the time, it dumps the contents of hardware structures.
+ */
+
+#ifdef DEBUG_PSA_SHOW
+/*------------------------------------------------------------------*/
+/*
+ * Print the formatted contents of the Parameter Storage Area.
+ */
+static void wv_psa_show(psa_t * p)
+{
+ printk(KERN_DEBUG "##### WaveLAN PSA contents: #####\n");
+ printk(KERN_DEBUG "psa_io_base_addr_1: 0x%02X %02X %02X %02X\n",
+ p->psa_io_base_addr_1,
+ p->psa_io_base_addr_2,
+ p->psa_io_base_addr_3, p->psa_io_base_addr_4);
+ printk(KERN_DEBUG "psa_rem_boot_addr_1: 0x%02X %02X %02X\n",
+ p->psa_rem_boot_addr_1,
+ p->psa_rem_boot_addr_2, p->psa_rem_boot_addr_3);
+ printk(KERN_DEBUG "psa_holi_params: 0x%02x, ", p->psa_holi_params);
+ printk("psa_int_req_no: %d\n", p->psa_int_req_no);
+#ifdef DEBUG_SHOW_UNUSED
+ printk(KERN_DEBUG
+ "psa_unused0[]: %02X:%02X:%02X:%02X:%02X:%02X:%02X\n",
+ p->psa_unused0[0], p->psa_unused0[1], p->psa_unused0[2],
+ p->psa_unused0[3], p->psa_unused0[4], p->psa_unused0[5],
+ p->psa_unused0[6]);
+#endif /* DEBUG_SHOW_UNUSED */
+ printk(KERN_DEBUG
+ "psa_univ_mac_addr[]: %02x:%02x:%02x:%02x:%02x:%02x\n",
+ p->psa_univ_mac_addr[0], p->psa_univ_mac_addr[1],
+ p->psa_univ_mac_addr[2], p->psa_univ_mac_addr[3],
+ p->psa_univ_mac_addr[4], p->psa_univ_mac_addr[5]);
+ printk(KERN_DEBUG
+ "psa_local_mac_addr[]: %02x:%02x:%02x:%02x:%02x:%02x\n",
+ p->psa_local_mac_addr[0], p->psa_local_mac_addr[1],
+ p->psa_local_mac_addr[2], p->psa_local_mac_addr[3],
+ p->psa_local_mac_addr[4], p->psa_local_mac_addr[5]);
+ printk(KERN_DEBUG "psa_univ_local_sel: %d, ",
+ p->psa_univ_local_sel);
+ printk("psa_comp_number: %d, ", p->psa_comp_number);
+ printk("psa_thr_pre_set: 0x%02x\n", p->psa_thr_pre_set);
+ printk(KERN_DEBUG "psa_feature_select/decay_prm: 0x%02x, ",
+ p->psa_feature_select);
+ printk("psa_subband/decay_update_prm: %d\n", p->psa_subband);
+ printk(KERN_DEBUG "psa_quality_thr: 0x%02x, ", p->psa_quality_thr);
+ printk("psa_mod_delay: 0x%02x\n", p->psa_mod_delay);
+ printk(KERN_DEBUG "psa_nwid: 0x%02x%02x, ", p->psa_nwid[0],
+ p->psa_nwid[1]);
+ printk("psa_nwid_select: %d\n", p->psa_nwid_select);
+ printk(KERN_DEBUG "psa_encryption_select: %d, ",
+ p->psa_encryption_select);
+ printk
+ ("psa_encryption_key[]: %02x:%02x:%02x:%02x:%02x:%02x:%02x:%02x\n",
+ p->psa_encryption_key[0], p->psa_encryption_key[1],
+ p->psa_encryption_key[2], p->psa_encryption_key[3],
+ p->psa_encryption_key[4], p->psa_encryption_key[5],
+ p->psa_encryption_key[6], p->psa_encryption_key[7]);
+ printk(KERN_DEBUG "psa_databus_width: %d\n", p->psa_databus_width);
+ printk(KERN_DEBUG "psa_call_code/auto_squelch: 0x%02x, ",
+ p->psa_call_code[0]);
+ printk
+ ("psa_call_code[]: %02X:%02X:%02X:%02X:%02X:%02X:%02X:%02X\n",
+ p->psa_call_code[0], p->psa_call_code[1], p->psa_call_code[2],
+ p->psa_call_code[3], p->psa_call_code[4], p->psa_call_code[5],
+ p->psa_call_code[6], p->psa_call_code[7]);
+#ifdef DEBUG_SHOW_UNUSED
+ printk(KERN_DEBUG "psa_reserved[]: %02X:%02X:%02X:%02X\n",
+ p->psa_reserved[0],
+ p->psa_reserved[1], p->psa_reserved[2], p->psa_reserved[3]);
+#endif /* DEBUG_SHOW_UNUSED */
+ printk(KERN_DEBUG "psa_conf_status: %d, ", p->psa_conf_status);
+ printk("psa_crc: 0x%02x%02x, ", p->psa_crc[0], p->psa_crc[1]);
+ printk("psa_crc_status: 0x%02x\n", p->psa_crc_status);
+} /* wv_psa_show */
+#endif /* DEBUG_PSA_SHOW */
+
+#ifdef DEBUG_MMC_SHOW
+/*------------------------------------------------------------------*/
+/*
+ * Print the formatted status of the Modem Management Controller.
+ * This function needs to be completed.
+ */
+static void wv_mmc_show(struct net_device * dev)
+{
+ unsigned long ioaddr = dev->base_addr;
+ net_local *lp = (net_local *) dev->priv;
+ mmr_t m;
+
+ /* Basic check */
+ if (hasr_read(ioaddr) & HASR_NO_CLK) {
+ printk(KERN_WARNING
+ "%s: wv_mmc_show: modem not connected\n",
+ dev->name);
+ return;
+ }
+
+ /* Read the mmc */
+ mmc_out(ioaddr, mmwoff(0, mmw_freeze), 1);
+ mmc_read(ioaddr, 0, (u8 *) & m, sizeof(m));
+ mmc_out(ioaddr, mmwoff(0, mmw_freeze), 0);
+
+#ifdef WIRELESS_EXT /* if wireless extension exists in the kernel */
+ /* Don't forget to update statistics */
+ lp->wstats.discard.nwid +=
+ (m.mmr_wrong_nwid_h << 8) | m.mmr_wrong_nwid_l;
+#endif /* WIRELESS_EXT */
+
+ printk(KERN_DEBUG "##### WaveLAN modem status registers: #####\n");
+#ifdef DEBUG_SHOW_UNUSED
+ printk(KERN_DEBUG
+ "mmc_unused0[]: %02X:%02X:%02X:%02X:%02X:%02X:%02X:%02X\n",
+ m.mmr_unused0[0], m.mmr_unused0[1], m.mmr_unused0[2],
+ m.mmr_unused0[3], m.mmr_unused0[4], m.mmr_unused0[5],
+ m.mmr_unused0[6], m.mmr_unused0[7]);
+#endif /* DEBUG_SHOW_UNUSED */
+ printk(KERN_DEBUG "Encryption algorithm: %02X - Status: %02X\n",
+ m.mmr_des_avail, m.mmr_des_status);
+#ifdef DEBUG_SHOW_UNUSED
+ printk(KERN_DEBUG "mmc_unused1[]: %02X:%02X:%02X:%02X:%02X\n",
+ m.mmr_unused1[0],
+ m.mmr_unused1[1],
+ m.mmr_unused1[2], m.mmr_unused1[3], m.mmr_unused1[4]);
+#endif /* DEBUG_SHOW_UNUSED */
+ printk(KERN_DEBUG "dce_status: 0x%x [%s%s%s%s]\n",
+ m.mmr_dce_status,
+ (m.
+ mmr_dce_status & MMR_DCE_STATUS_RX_BUSY) ?
+ "energy detected," : "",
+ (m.
+ mmr_dce_status & MMR_DCE_STATUS_LOOPT_IND) ?
+ "loop test indicated," : "",
+ (m.
+ mmr_dce_status & MMR_DCE_STATUS_TX_BUSY) ?
+ "transmitter on," : "",
+ (m.
+ mmr_dce_status & MMR_DCE_STATUS_JBR_EXPIRED) ?
+ "jabber timer expired," : "");
+ printk(KERN_DEBUG "Dsp ID: %02X\n", m.mmr_dsp_id);
+#ifdef DEBUG_SHOW_UNUSED
+ printk(KERN_DEBUG "mmc_unused2[]: %02X:%02X\n",
+ m.mmr_unused2[0], m.mmr_unused2[1]);
+#endif /* DEBUG_SHOW_UNUSED */
+ printk(KERN_DEBUG "# correct_nwid: %d, # wrong_nwid: %d\n",
+ (m.mmr_correct_nwid_h << 8) | m.mmr_correct_nwid_l,
+ (m.mmr_wrong_nwid_h << 8) | m.mmr_wrong_nwid_l);
+ printk(KERN_DEBUG "thr_pre_set: 0x%x [current signal %s]\n",
+ m.mmr_thr_pre_set & MMR_THR_PRE_SET,
+ (m.
+ mmr_thr_pre_set & MMR_THR_PRE_SET_CUR) ? "above" :
+ "below");
+ printk(KERN_DEBUG "signal_lvl: %d [%s], ",
+ m.mmr_signal_lvl & MMR_SIGNAL_LVL,
+ (m.
+ mmr_signal_lvl & MMR_SIGNAL_LVL_VALID) ? "new msg" :
+ "no new msg");
+ printk("silence_lvl: %d [%s], ",
+ m.mmr_silence_lvl & MMR_SILENCE_LVL,
+ (m.
+ mmr_silence_lvl & MMR_SILENCE_LVL_VALID) ? "update done" :
+ "no new update");
+ printk("sgnl_qual: 0x%x [%s]\n", m.mmr_sgnl_qual & MMR_SGNL_QUAL,
+ (m.
+ mmr_sgnl_qual & MMR_SGNL_QUAL_ANT) ? "Antenna 1" :
+ "Antenna 0");
+#ifdef DEBUG_SHOW_UNUSED
+ printk(KERN_DEBUG "netw_id_l: %x\n", m.mmr_netw_id_l);
+#endif /* DEBUG_SHOW_UNUSED */
+} /* wv_mmc_show */
+#endif /* DEBUG_MMC_SHOW */
+
+#ifdef DEBUG_I82586_SHOW
+/*------------------------------------------------------------------*/
+/*
+ * Print the last block of the i82586 memory.
+ */
+static void wv_scb_show(unsigned long ioaddr)
+{
+ scb_t scb;
+
+ obram_read(ioaddr, OFFSET_SCB, (unsigned char *) &scb,
+ sizeof(scb));
+
+ printk(KERN_DEBUG "##### WaveLAN system control block: #####\n");
+
+ printk(KERN_DEBUG "status: ");
+ printk("stat 0x%x[%s%s%s%s] ",
+ (scb.
+ scb_status & (SCB_ST_CX | SCB_ST_FR | SCB_ST_CNA |
+ SCB_ST_RNR)) >> 12,
+ (scb.
+ scb_status & SCB_ST_CX) ? "command completion interrupt," :
+ "", (scb.scb_status & SCB_ST_FR) ? "frame received," : "",
+ (scb.
+ scb_status & SCB_ST_CNA) ? "command unit not active," : "",
+ (scb.
+ scb_status & SCB_ST_RNR) ? "receiving unit not ready," :
+ "");
+ printk("cus 0x%x[%s%s%s] ", (scb.scb_status & SCB_ST_CUS) >> 8,
+ ((scb.scb_status & SCB_ST_CUS) ==
+ SCB_ST_CUS_IDLE) ? "idle" : "",
+ ((scb.scb_status & SCB_ST_CUS) ==
+ SCB_ST_CUS_SUSP) ? "suspended" : "",
+ ((scb.scb_status & SCB_ST_CUS) ==
+ SCB_ST_CUS_ACTV) ? "active" : "");
+ printk("rus 0x%x[%s%s%s%s]\n", (scb.scb_status & SCB_ST_RUS) >> 4,
+ ((scb.scb_status & SCB_ST_RUS) ==
+ SCB_ST_RUS_IDLE) ? "idle" : "",
+ ((scb.scb_status & SCB_ST_RUS) ==
+ SCB_ST_RUS_SUSP) ? "suspended" : "",
+ ((scb.scb_status & SCB_ST_RUS) ==
+ SCB_ST_RUS_NRES) ? "no resources" : "",
+ ((scb.scb_status & SCB_ST_RUS) ==
+ SCB_ST_RUS_RDY) ? "ready" : "");
+
+ printk(KERN_DEBUG "command: ");
+ printk("ack 0x%x[%s%s%s%s] ",
+ (scb.
+ scb_command & (SCB_CMD_ACK_CX | SCB_CMD_ACK_FR |
+ SCB_CMD_ACK_CNA | SCB_CMD_ACK_RNR)) >> 12,
+ (scb.
+ scb_command & SCB_CMD_ACK_CX) ? "ack cmd completion," : "",
+ (scb.
+ scb_command & SCB_CMD_ACK_FR) ? "ack frame received," : "",
+ (scb.
+ scb_command & SCB_CMD_ACK_CNA) ? "ack CU not active," : "",
+ (scb.
+ scb_command & SCB_CMD_ACK_RNR) ? "ack RU not ready," : "");
+ printk("cuc 0x%x[%s%s%s%s%s] ",
+ (scb.scb_command & SCB_CMD_CUC) >> 8,
+ ((scb.scb_command & SCB_CMD_CUC) ==
+ SCB_CMD_CUC_NOP) ? "nop" : "",
+ ((scb.scb_command & SCB_CMD_CUC) ==
+ SCB_CMD_CUC_GO) ? "start cbl_offset" : "",
+ ((scb.scb_command & SCB_CMD_CUC) ==
+ SCB_CMD_CUC_RES) ? "resume execution" : "",
+ ((scb.scb_command & SCB_CMD_CUC) ==
+ SCB_CMD_CUC_SUS) ? "suspend execution" : "",
+ ((scb.scb_command & SCB_CMD_CUC) ==
+ SCB_CMD_CUC_ABT) ? "abort execution" : "");
+ printk("ruc 0x%x[%s%s%s%s%s]\n",
+ (scb.scb_command & SCB_CMD_RUC) >> 4,
+ ((scb.scb_command & SCB_CMD_RUC) ==
+ SCB_CMD_RUC_NOP) ? "nop" : "",
+ ((scb.scb_command & SCB_CMD_RUC) ==
+ SCB_CMD_RUC_GO) ? "start rfa_offset" : "",
+ ((scb.scb_command & SCB_CMD_RUC) ==
+ SCB_CMD_RUC_RES) ? "resume reception" : "",
+ ((scb.scb_command & SCB_CMD_RUC) ==
+ SCB_CMD_RUC_SUS) ? "suspend reception" : "",
+ ((scb.scb_command & SCB_CMD_RUC) ==
+ SCB_CMD_RUC_ABT) ? "abort reception" : "");
+
+ printk(KERN_DEBUG "cbl_offset 0x%x ", scb.scb_cbl_offset);
+ printk("rfa_offset 0x%x\n", scb.scb_rfa_offset);
+
+ printk(KERN_DEBUG "crcerrs %d ", scb.scb_crcerrs);
+ printk("alnerrs %d ", scb.scb_alnerrs);
+ printk("rscerrs %d ", scb.scb_rscerrs);
+ printk("ovrnerrs %d\n", scb.scb_ovrnerrs);
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Print the formatted status of the i82586's receive unit.
+ */
+static void wv_ru_show(struct net_device * dev)
+{
+ /* net_local *lp = (net_local *) dev->priv; */
+
+ printk(KERN_DEBUG
+ "##### WaveLAN i82586 receiver unit status: #####\n");
+ printk(KERN_DEBUG "ru:");
+ /*
+ * Not implemented yet
+ */
+ printk("\n");
+} /* wv_ru_show */
+
+/*------------------------------------------------------------------*/
+/*
+ * Display info about one control block of the i82586 memory.
+ */
+static void wv_cu_show_one(struct net_device * dev, net_local * lp, int i, u16 p)
+{
+ unsigned long ioaddr;
+ ac_tx_t actx;
+
+ ioaddr = dev->base_addr;
+
+ printk("%d: 0x%x:", i, p);
+
+ obram_read(ioaddr, p, (unsigned char *) &actx, sizeof(actx));
+ printk(" status=0x%x,", actx.tx_h.ac_status);
+ printk(" command=0x%x,", actx.tx_h.ac_command);
+
+ /*
+ {
+ tbd_t tbd;
+
+ obram_read(ioaddr, actx.tx_tbd_offset, (unsigned char *)&tbd, sizeof(tbd));
+ printk(" tbd_status=0x%x,", tbd.tbd_status);
+ }
+ */
+
+ printk("|");
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Print status of the command unit of the i82586.
+ */
+static void wv_cu_show(struct net_device * dev)
+{
+ net_local *lp = (net_local *) dev->priv;
+ unsigned int i;
+ u16 p;
+
+ printk(KERN_DEBUG
+ "##### WaveLAN i82586 command unit status: #####\n");
+
+ printk(KERN_DEBUG);
+ for (i = 0, p = lp->tx_first_in_use; i < NTXBLOCKS; i++) {
+ wv_cu_show_one(dev, lp, i, p);
+
+ p += TXBLOCKZ;
+ if (p >= OFFSET_CU + NTXBLOCKS * TXBLOCKZ)
+ p -= NTXBLOCKS * TXBLOCKZ;
+ }
+ printk("\n");
+}
+#endif /* DEBUG_I82586_SHOW */
+
+#ifdef DEBUG_DEVICE_SHOW
+/*------------------------------------------------------------------*/
+/*
+ * Print the formatted status of the WaveLAN PCMCIA device driver.
+ */
+static void wv_dev_show(struct net_device * dev)
+{
+ printk(KERN_DEBUG "dev:");
+ printk(" state=%lX,", dev->state);
+ printk(" trans_start=%ld,", dev->trans_start);
+ printk(" flags=0x%x,", dev->flags);
+ printk("\n");
+} /* wv_dev_show */
+
+/*------------------------------------------------------------------*/
+/*
+ * Print the formatted status of the WaveLAN PCMCIA device driver's
+ * private information.
+ */
+static void wv_local_show(struct net_device * dev)
+{
+ net_local *lp;
+
+ lp = (net_local *) dev->priv;
+
+ printk(KERN_DEBUG "local:");
+ printk(" tx_n_in_use=%d,", lp->tx_n_in_use);
+ printk(" hacr=0x%x,", lp->hacr);
+ printk(" rx_head=0x%x,", lp->rx_head);
+ printk(" rx_last=0x%x,", lp->rx_last);
+ printk(" tx_first_free=0x%x,", lp->tx_first_free);
+ printk(" tx_first_in_use=0x%x,", lp->tx_first_in_use);
+ printk("\n");
+} /* wv_local_show */
+#endif /* DEBUG_DEVICE_SHOW */
+
+#if defined(DEBUG_RX_INFO) || defined(DEBUG_TX_INFO)
+/*------------------------------------------------------------------*/
+/*
+ * Dump packet header (and content if necessary) on the screen
+ */
+static inline void wv_packet_info(u8 * p, /* Packet to dump */
+ int length, /* Length of the packet */
+ char *msg1, /* Name of the device */
+ char *msg2)
+{ /* Name of the function */
+ int i;
+ int maxi;
+
+ printk(KERN_DEBUG
+ "%s: %s(): dest %02X:%02X:%02X:%02X:%02X:%02X, length %d\n",
+ msg1, msg2, p[0], p[1], p[2], p[3], p[4], p[5], length);
+ printk(KERN_DEBUG
+ "%s: %s(): src %02X:%02X:%02X:%02X:%02X:%02X, type 0x%02X%02X\n",
+ msg1, msg2, p[6], p[7], p[8], p[9], p[10], p[11], p[12],
+ p[13]);
+
+#ifdef DEBUG_PACKET_DUMP
+
+ printk(KERN_DEBUG "data=\"");
+
+ if ((maxi = length) > DEBUG_PACKET_DUMP)
+ maxi = DEBUG_PACKET_DUMP;
+ for (i = 14; i < maxi; i++)
+ if (p[i] >= ' ' && p[i] <= '~')
+ printk(" %c", p[i]);
+ else
+ printk("%02X", p[i]);
+ if (maxi < length)
+ printk("..");
+ printk("\"\n");
+ printk(KERN_DEBUG "\n");
+#endif /* DEBUG_PACKET_DUMP */
+}
+#endif /* defined(DEBUG_RX_INFO) || defined(DEBUG_TX_INFO) */
+
+/*------------------------------------------------------------------*/
+/*
+ * This is the information which is displayed by the driver at startup.
+ * There are lots of flags for configuring it to your liking.
+ */
+static inline void wv_init_info(struct net_device * dev)
+{
+ short ioaddr = dev->base_addr;
+ net_local *lp = (net_local *) dev->priv;
+ psa_t psa;
+ int i;
+
+ /* Read the parameter storage area */
+ psa_read(ioaddr, lp->hacr, 0, (unsigned char *) &psa, sizeof(psa));
+
+#ifdef DEBUG_PSA_SHOW
+ wv_psa_show(&psa);
+#endif
+#ifdef DEBUG_MMC_SHOW
+ wv_mmc_show(dev);
+#endif
+#ifdef DEBUG_I82586_SHOW
+ wv_cu_show(dev);
+#endif
+
+#ifdef DEBUG_BASIC_SHOW
+ /* Now, let's go for the basic stuff. */
+ printk(KERN_NOTICE "%s: WaveLAN at %#x,", dev->name, ioaddr);
+ for (i = 0; i < WAVELAN_ADDR_SIZE; i++)
+ printk("%s%02X", (i == 0) ? " " : ":", dev->dev_addr[i]);
+ printk(", IRQ %d", dev->irq);
+
+ /* Print current network ID. */
+ if (psa.psa_nwid_select)
+ printk(", nwid 0x%02X-%02X", psa.psa_nwid[0],
+ psa.psa_nwid[1]);
+ else
+ printk(", nwid off");
+
+ /* If 2.00 card */
+ if (!(mmc_in(ioaddr, mmroff(0, mmr_fee_status)) &
+ (MMR_FEE_STATUS_DWLD | MMR_FEE_STATUS_BUSY))) {
+ unsigned short freq;
+
+ /* Ask the EEPROM to read the frequency from the first area. */
+ fee_read(ioaddr, 0x00, &freq, 1);
+
+ /* Print frequency */
+ printk(", 2.00, %ld", (freq >> 6) + 2400L);
+
+ /* Hack! */
+ if (freq & 0x20)
+ printk(".5");
+ } else {
+ printk(", PC");
+ switch (psa.psa_comp_number) {
+ case PSA_COMP_PC_AT_915:
+ case PSA_COMP_PC_AT_2400:
+ printk("-AT");
+ break;
+ case PSA_COMP_PC_MC_915:
+ case PSA_COMP_PC_MC_2400:
+ printk("-MC");
+ break;
+ case PSA_COMP_PCMCIA_915:
+ printk("MCIA");
+ break;
+ default:
+ printk("?");
+ }
+ printk(", ");
+ switch (psa.psa_subband) {
+ case PSA_SUBBAND_915:
+ printk("915");
+ break;
+ case PSA_SUBBAND_2425:
+ printk("2425");
+ break;
+ case PSA_SUBBAND_2460:
+ printk("2460");
+ break;
+ case PSA_SUBBAND_2484:
+ printk("2484");
+ break;
+ case PSA_SUBBAND_2430_5:
+ printk("2430.5");
+ break;
+ default:
+ printk("?");
+ }
+ }
+
+ printk(" MHz\n");
+#endif /* DEBUG_BASIC_SHOW */
+
+#ifdef DEBUG_VERSION_SHOW
+ /* Print version information */
+ printk(KERN_NOTICE "%s", version);
+#endif
+} /* wv_init_info */
+
+/********************* IOCTL, STATS & RECONFIG *********************/
+/*
+ * We found here routines that are called by Linux on different
+ * occasions after the configuration and not for transmitting data
+ * These may be called when the user use ifconfig, /proc/net/dev
+ * or wireless extensions
+ */
+
+/*------------------------------------------------------------------*/
+/*
+ * Get the current Ethernet statistics. This may be called with the
+ * card open or closed.
+ * Used when the user read /proc/net/dev
+ */
+static en_stats *wavelan_get_stats(struct net_device * dev)
+{
+#ifdef DEBUG_IOCTL_TRACE
+ printk(KERN_DEBUG "%s: <>wavelan_get_stats()\n", dev->name);
+#endif
+
+ return (&((net_local *) dev->priv)->stats);
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Set or clear the multicast filter for this adaptor.
+ * num_addrs == -1 Promiscuous mode, receive all packets
+ * num_addrs == 0 Normal mode, clear multicast list
+ * num_addrs > 0 Multicast mode, receive normal and MC packets,
+ * and do best-effort filtering.
+ */
+static void wavelan_set_multicast_list(struct net_device * dev)
+{
+ net_local *lp = (net_local *) dev->priv;
+
+#ifdef DEBUG_IOCTL_TRACE
+ printk(KERN_DEBUG "%s: ->wavelan_set_multicast_list()\n",
+ dev->name);
+#endif
+
+#ifdef DEBUG_IOCTL_INFO
+ printk(KERN_DEBUG
+ "%s: wavelan_set_multicast_list(): setting Rx mode %02X to %d addresses.\n",
+ dev->name, dev->flags, dev->mc_count);
+#endif
+
+ /* Are we asking for promiscuous mode,
+ * or all multicast addresses (we don't have that!)
+ * or too many multicast addresses for the hardware filter? */
+ if ((dev->flags & IFF_PROMISC) ||
+ (dev->flags & IFF_ALLMULTI) ||
+ (dev->mc_count > I82586_MAX_MULTICAST_ADDRESSES)) {
+ /*
+ * Enable promiscuous mode: receive all packets.
+ */
+ if (!lp->promiscuous) {
+ lp->promiscuous = 1;
+ lp->mc_count = 0;
+
+ wv_82586_reconfig(dev);
+
+ /* Tell the kernel that we are doing a really bad job. */
+ dev->flags |= IFF_PROMISC;
+ }
+ } else
+ /* Are there multicast addresses to send? */
+ if (dev->mc_list != (struct dev_mc_list *) NULL) {
+ /*
+ * Disable promiscuous mode, but receive all packets
+ * in multicast list
+ */
+#ifdef MULTICAST_AVOID
+ if (lp->promiscuous || (dev->mc_count != lp->mc_count))
+#endif
+ {
+ lp->promiscuous = 0;
+ lp->mc_count = dev->mc_count;
+
+ wv_82586_reconfig(dev);
+ }
+ } else {
+ /*
+ * Switch to normal mode: disable promiscuous mode and
+ * clear the multicast list.
+ */
+ if (lp->promiscuous || lp->mc_count == 0) {
+ lp->promiscuous = 0;
+ lp->mc_count = 0;
+
+ wv_82586_reconfig(dev);
+ }
+ }
+#ifdef DEBUG_IOCTL_TRACE
+ printk(KERN_DEBUG "%s: <-wavelan_set_multicast_list()\n",
+ dev->name);
+#endif
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * This function doesn't exist.
+ * (Note : it was a nice way to test the reconfigure stuff...)
+ */
+#ifdef SET_MAC_ADDRESS
+static int wavelan_set_mac_address(struct net_device * dev, void *addr)
+{
+ struct sockaddr *mac = addr;
+
+ /* Copy the address. */
+ memcpy(dev->dev_addr, mac->sa_data, WAVELAN_ADDR_SIZE);
+
+ /* Reconfigure the beast. */
+ wv_82586_reconfig(dev);
+
+ return 0;
+}
+#endif /* SET_MAC_ADDRESS */
+
+#ifdef WIRELESS_EXT /* if wireless extensions exist in the kernel */
+
+/*------------------------------------------------------------------*/
+/*
+ * Frequency setting (for hardware capable of it)
+ * It's a bit complicated and you don't really want to look into it.
+ * (called in wavelan_ioctl)
+ */
+static inline int wv_set_frequency(unsigned long ioaddr, /* I/O port of the card */
+ iw_freq * frequency)
+{
+ const int BAND_NUM = 10; /* Number of bands */
+ long freq = 0L; /* offset to 2.4 GHz in .5 MHz */
+#ifdef DEBUG_IOCTL_INFO
+ int i;
+#endif
+
+ /* Setting by frequency */
+ /* Theoretically, you may set any frequency between
+ * the two limits with a 0.5 MHz precision. In practice,
+ * I don't want you to have trouble with local regulations.
+ */
+ if ((frequency->e == 1) &&
+ (frequency->m >= (int) 2.412e8)
+ && (frequency->m <= (int) 2.487e8)) {
+ freq = ((frequency->m / 10000) - 24000L) / 5;
+ }
+
+ /* Setting by channel (same as wfreqsel) */
+ /* Warning: each channel is 22 MHz wide, so some of the channels
+ * will interfere. */
+ if ((frequency->e == 0) && (frequency->m < BAND_NUM)) {
+ /* Get frequency offset. */
+ freq = channel_bands[frequency->m] >> 1;
+ }
+
+ /* Verify that the frequency is allowed. */
+ if (freq != 0L) {
+ u16 table[10]; /* Authorized frequency table */
+
+ /* Read the frequency table. */
+ fee_read(ioaddr, 0x71, table, 10);
+
+#ifdef DEBUG_IOCTL_INFO
+ printk(KERN_DEBUG "Frequency table: ");
+ for (i = 0; i < 10; i++) {
+ printk(" %04X", table[i]);
+ }
+ printk("\n");
+#endif
+
+ /* Look in the table to see whether the frequency is allowed. */
+ if (!(table[9 - ((freq - 24) / 16)] &
+ (1 << ((freq - 24) % 16)))) return -EINVAL; /* not allowed */
+ } else
+ return -EINVAL;
+
+ /* if we get a usable frequency */
+ if (freq != 0L) {
+ unsigned short area[16];
+ unsigned short dac[2];
+ unsigned short area_verify[16];
+ unsigned short dac_verify[2];
+ /* Corresponding gain (in the power adjust value table)
+ * See AT&T WaveLAN Data Manual, REF 407-024689/E, page 3-8
+ * and WCIN062D.DOC, page 6.2.9. */
+ unsigned short power_limit[] = { 40, 80, 120, 160, 0 };
+ int power_band = 0; /* Selected band */
+ unsigned short power_adjust; /* Correct value */
+
+ /* Search for the gain. */
+ power_band = 0;
+ while ((freq > power_limit[power_band]) &&
+ (power_limit[++power_band] != 0));
+
+ /* Read the first area. */
+ fee_read(ioaddr, 0x00, area, 16);
+
+ /* Read the DAC. */
+ fee_read(ioaddr, 0x60, dac, 2);
+
+ /* Read the new power adjust value. */
+ fee_read(ioaddr, 0x6B - (power_band >> 1), &power_adjust,
+ 1);
+ if (power_band & 0x1)
+ power_adjust >>= 8;
+ else
+ power_adjust &= 0xFF;
+
+#ifdef DEBUG_IOCTL_INFO
+ printk(KERN_DEBUG "WaveLAN EEPROM Area 1: ");
+ for (i = 0; i < 16; i++) {
+ printk(" %04X", area[i]);
+ }
+ printk("\n");
+
+ printk(KERN_DEBUG "WaveLAN EEPROM DAC: %04X %04X\n",
+ dac[0], dac[1]);
+#endif
+
+ /* Frequency offset (for info only) */
+ area[0] = ((freq << 5) & 0xFFE0) | (area[0] & 0x1F);
+
+ /* Receiver Principle main divider coefficient */
+ area[3] = (freq >> 1) + 2400L - 352L;
+ area[2] = ((freq & 0x1) << 4) | (area[2] & 0xFFEF);
+
+ /* Transmitter Main divider coefficient */
+ area[13] = (freq >> 1) + 2400L;
+ area[12] = ((freq & 0x1) << 4) | (area[2] & 0xFFEF);
+
+ /* Other parts of the area are flags, bit streams or unused. */
+
+ /* Set the value in the DAC. */
+ dac[1] = ((power_adjust >> 1) & 0x7F) | (dac[1] & 0xFF80);
+ dac[0] = ((power_adjust & 0x1) << 4) | (dac[0] & 0xFFEF);
+
+ /* Write the first area. */
+ fee_write(ioaddr, 0x00, area, 16);
+
+ /* Write the DAC. */
+ fee_write(ioaddr, 0x60, dac, 2);
+
+ /* We now should verify here that the writing of the EEPROM went OK. */
+
+ /* Reread the first area. */
+ fee_read(ioaddr, 0x00, area_verify, 16);
+
+ /* Reread the DAC. */
+ fee_read(ioaddr, 0x60, dac_verify, 2);
+
+ /* Compare. */
+ if (memcmp(area, area_verify, 16 * 2) ||
+ memcmp(dac, dac_verify, 2 * 2)) {
+#ifdef DEBUG_IOCTL_ERROR
+ printk(KERN_INFO
+ "WaveLAN: wv_set_frequency: unable to write new frequency to EEPROM(?).\n");
+#endif
+ return -EOPNOTSUPP;
+ }
+
+ /* We must download the frequency parameters to the
+ * synthesizers (from the EEPROM - area 1)
+ * Note: as the EEPROM is automatically decremented, we set the end
+ * if the area... */
+ mmc_out(ioaddr, mmwoff(0, mmw_fee_addr), 0x0F);
+ mmc_out(ioaddr, mmwoff(0, mmw_fee_ctrl),
+ MMW_FEE_CTRL_READ | MMW_FEE_CTRL_DWLD);
+
+ /* Wait until the download is finished. */
+ fee_wait(ioaddr, 100, 100);
+
+ /* We must now download the power adjust value (gain) to
+ * the synthesizers (from the EEPROM - area 7 - DAC). */
+ mmc_out(ioaddr, mmwoff(0, mmw_fee_addr), 0x61);
+ mmc_out(ioaddr, mmwoff(0, mmw_fee_ctrl),
+ MMW_FEE_CTRL_READ | MMW_FEE_CTRL_DWLD);
+
+ /* Wait for the download to finish. */
+ fee_wait(ioaddr, 100, 100);
+
+#ifdef DEBUG_IOCTL_INFO
+ /* Verification of what we have done */
+
+ printk(KERN_DEBUG "WaveLAN EEPROM Area 1: ");
+ for (i = 0; i < 16; i++) {
+ printk(" %04X", area_verify[i]);
+ }
+ printk("\n");
+
+ printk(KERN_DEBUG "WaveLAN EEPROM DAC: %04X %04X\n",
+ dac_verify[0], dac_verify[1]);
+#endif
+
+ return 0;
+ } else
+ return -EINVAL; /* Bah, never get there... */
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Give the list of available frequencies.
+ */
+static inline int wv_frequency_list(unsigned long ioaddr, /* I/O port of the card */
+ iw_freq * list, /* List of frequencies to fill */
+ int max)
+{ /* Maximum number of frequencies */
+ u16 table[10]; /* Authorized frequency table */
+ long freq = 0L; /* offset to 2.4 GHz in .5 MHz + 12 MHz */
+ int i; /* index in the table */
+ int c = 0; /* Channel number */
+
+ /* Read the frequency table. */
+ fee_read(ioaddr, 0x71 /* frequency table */ , table, 10);
+
+ /* Check all frequencies. */
+ i = 0;
+ for (freq = 0; freq < 150; freq++)
+ /* Look in the table if the frequency is allowed */
+ if (table[9 - (freq / 16)] & (1 << (freq % 16))) {
+ /* Compute approximate channel number */
+ while ((((channel_bands[c] >> 1) - 24) < freq) &&
+ (c < NELS(channel_bands)))
+ c++;
+ list[i].i = c; /* Set the list index */
+
+ /* put in the list */
+ list[i].m = (((freq + 24) * 5) + 24000L) * 10000;
+ list[i++].e = 1;
+
+ /* Check number. */
+ if (i >= max)
+ return (i);
+ }
+
+ return (i);
+}
+
+#ifdef IW_WIRELESS_SPY
+/*------------------------------------------------------------------*/
+/*
+ * Gather wireless spy statistics: for each packet, compare the source
+ * address with our list, and if they match, get the statistics.
+ * Sorry, but this function really needs the wireless extensions.
+ */
+static inline void wl_spy_gather(struct net_device * dev,
+ u8 * mac, /* MAC address */
+ u8 * stats) /* Statistics to gather */
+{
+ struct iw_quality wstats;
+
+ wstats.qual = stats[2] & MMR_SGNL_QUAL;
+ wstats.level = stats[0] & MMR_SIGNAL_LVL;
+ wstats.noise = stats[1] & MMR_SILENCE_LVL;
+ wstats.updated = 0x7;
+
+ /* Update spy records */
+ wireless_spy_update(dev, mac, &wstats);
+}
+#endif /* IW_WIRELESS_SPY */
+
+#ifdef HISTOGRAM
+/*------------------------------------------------------------------*/
+/*
+ * This function calculates a histogram of the signal level.
+ * As the noise is quite constant, it's like doing it on the SNR.
+ * We have defined a set of interval (lp->his_range), and each time
+ * the level goes in that interval, we increment the count (lp->his_sum).
+ * With this histogram you may detect if one WaveLAN is really weak,
+ * or you may also calculate the mean and standard deviation of the level.
+ */
+static inline void wl_his_gather(struct net_device * dev, u8 * stats)
+{ /* Statistics to gather */
+ net_local *lp = (net_local *) dev->priv;
+ u8 level = stats[0] & MMR_SIGNAL_LVL;
+ int i;
+
+ /* Find the correct interval. */
+ i = 0;
+ while ((i < (lp->his_number - 1))
+ && (level >= lp->his_range[i++]));
+
+ /* Increment interval counter. */
+ (lp->his_sum[i])++;
+}
+#endif /* HISTOGRAM */
+
+/*------------------------------------------------------------------*/
+/*
+ * Wireless Handler : get protocol name
+ */
+static int wavelan_get_name(struct net_device *dev,
+ struct iw_request_info *info,
+ union iwreq_data *wrqu,
+ char *extra)
+{
+ strcpy(wrqu->name, "WaveLAN");
+ return 0;
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Wireless Handler : set NWID
+ */
+static int wavelan_set_nwid(struct net_device *dev,
+ struct iw_request_info *info,
+ union iwreq_data *wrqu,
+ char *extra)
+{
+ unsigned long ioaddr = dev->base_addr;
+ net_local *lp = (net_local *) dev->priv; /* lp is not unused */
+ psa_t psa;
+ mm_t m;
+ unsigned long flags;
+ int ret = 0;
+
+ /* Disable interrupts and save flags. */
+ spin_lock_irqsave(&lp->spinlock, flags);
+
+ /* Set NWID in WaveLAN. */
+ if (!wrqu->nwid.disabled) {
+ /* Set NWID in psa */
+ psa.psa_nwid[0] = (wrqu->nwid.value & 0xFF00) >> 8;
+ psa.psa_nwid[1] = wrqu->nwid.value & 0xFF;
+ psa.psa_nwid_select = 0x01;
+ psa_write(ioaddr, lp->hacr,
+ (char *) psa.psa_nwid - (char *) &psa,
+ (unsigned char *) psa.psa_nwid, 3);
+
+ /* Set NWID in mmc. */
+ m.w.mmw_netw_id_l = psa.psa_nwid[1];
+ m.w.mmw_netw_id_h = psa.psa_nwid[0];
+ mmc_write(ioaddr,
+ (char *) &m.w.mmw_netw_id_l -
+ (char *) &m,
+ (unsigned char *) &m.w.mmw_netw_id_l, 2);
+ mmc_out(ioaddr, mmwoff(0, mmw_loopt_sel), 0x00);
+ } else {
+ /* Disable NWID in the psa. */
+ psa.psa_nwid_select = 0x00;
+ psa_write(ioaddr, lp->hacr,
+ (char *) &psa.psa_nwid_select -
+ (char *) &psa,
+ (unsigned char *) &psa.psa_nwid_select,
+ 1);
+
+ /* Disable NWID in the mmc (no filtering). */
+ mmc_out(ioaddr, mmwoff(0, mmw_loopt_sel),
+ MMW_LOOPT_SEL_DIS_NWID);
+ }
+ /* update the Wavelan checksum */
+ update_psa_checksum(dev, ioaddr, lp->hacr);
+
+ /* Enable interrupts and restore flags. */
+ spin_unlock_irqrestore(&lp->spinlock, flags);
+
+ return ret;
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Wireless Handler : get NWID
+ */
+static int wavelan_get_nwid(struct net_device *dev,
+ struct iw_request_info *info,
+ union iwreq_data *wrqu,
+ char *extra)
+{
+ unsigned long ioaddr = dev->base_addr;
+ net_local *lp = (net_local *) dev->priv; /* lp is not unused */
+ psa_t psa;
+ unsigned long flags;
+ int ret = 0;
+
+ /* Disable interrupts and save flags. */
+ spin_lock_irqsave(&lp->spinlock, flags);
+
+ /* Read the NWID. */
+ psa_read(ioaddr, lp->hacr,
+ (char *) psa.psa_nwid - (char *) &psa,
+ (unsigned char *) psa.psa_nwid, 3);
+ wrqu->nwid.value = (psa.psa_nwid[0] << 8) + psa.psa_nwid[1];
+ wrqu->nwid.disabled = !(psa.psa_nwid_select);
+ wrqu->nwid.fixed = 1; /* Superfluous */
+
+ /* Enable interrupts and restore flags. */
+ spin_unlock_irqrestore(&lp->spinlock, flags);
+
+ return ret;
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Wireless Handler : set frequency
+ */
+static int wavelan_set_freq(struct net_device *dev,
+ struct iw_request_info *info,
+ union iwreq_data *wrqu,
+ char *extra)
+{
+ unsigned long ioaddr = dev->base_addr;
+ net_local *lp = (net_local *) dev->priv; /* lp is not unused */
+ unsigned long flags;
+ int ret;
+
+ /* Disable interrupts and save flags. */
+ spin_lock_irqsave(&lp->spinlock, flags);
+
+ /* Attempt to recognise 2.00 cards (2.4 GHz frequency selectable). */
+ if (!(mmc_in(ioaddr, mmroff(0, mmr_fee_status)) &
+ (MMR_FEE_STATUS_DWLD | MMR_FEE_STATUS_BUSY)))
+ ret = wv_set_frequency(ioaddr, &(wrqu->freq));
+ else
+ ret = -EOPNOTSUPP;
+
+ /* Enable interrupts and restore flags. */
+ spin_unlock_irqrestore(&lp->spinlock, flags);
+
+ return ret;
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Wireless Handler : get frequency
+ */
+static int wavelan_get_freq(struct net_device *dev,
+ struct iw_request_info *info,
+ union iwreq_data *wrqu,
+ char *extra)
+{
+ unsigned long ioaddr = dev->base_addr;
+ net_local *lp = (net_local *) dev->priv; /* lp is not unused */
+ psa_t psa;
+ unsigned long flags;
+ int ret = 0;
+
+ /* Disable interrupts and save flags. */
+ spin_lock_irqsave(&lp->spinlock, flags);
+
+ /* Attempt to recognise 2.00 cards (2.4 GHz frequency selectable).
+ * Does it work for everybody, especially old cards? */
+ if (!(mmc_in(ioaddr, mmroff(0, mmr_fee_status)) &
+ (MMR_FEE_STATUS_DWLD | MMR_FEE_STATUS_BUSY))) {
+ unsigned short freq;
+
+ /* Ask the EEPROM to read the frequency from the first area. */
+ fee_read(ioaddr, 0x00, &freq, 1);
+ wrqu->freq.m = ((freq >> 5) * 5 + 24000L) * 10000;
+ wrqu->freq.e = 1;
+ } else {
+ psa_read(ioaddr, lp->hacr,
+ (char *) &psa.psa_subband - (char *) &psa,
+ (unsigned char *) &psa.psa_subband, 1);
+
+ if (psa.psa_subband <= 4) {
+ wrqu->freq.m = fixed_bands[psa.psa_subband];
+ wrqu->freq.e = (psa.psa_subband != 0);
+ } else
+ ret = -EOPNOTSUPP;
+ }
+
+ /* Enable interrupts and restore flags. */
+ spin_unlock_irqrestore(&lp->spinlock, flags);
+
+ return ret;
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Wireless Handler : set level threshold
+ */
+static int wavelan_set_sens(struct net_device *dev,
+ struct iw_request_info *info,
+ union iwreq_data *wrqu,
+ char *extra)
+{
+ unsigned long ioaddr = dev->base_addr;
+ net_local *lp = (net_local *) dev->priv; /* lp is not unused */
+ psa_t psa;
+ unsigned long flags;
+ int ret = 0;
+
+ /* Disable interrupts and save flags. */
+ spin_lock_irqsave(&lp->spinlock, flags);
+
+ /* Set the level threshold. */
+ /* We should complain loudly if wrqu->sens.fixed = 0, because we
+ * can't set auto mode... */
+ psa.psa_thr_pre_set = wrqu->sens.value & 0x3F;
+ psa_write(ioaddr, lp->hacr,
+ (char *) &psa.psa_thr_pre_set - (char *) &psa,
+ (unsigned char *) &psa.psa_thr_pre_set, 1);
+ /* update the Wavelan checksum */
+ update_psa_checksum(dev, ioaddr, lp->hacr);
+ mmc_out(ioaddr, mmwoff(0, mmw_thr_pre_set),
+ psa.psa_thr_pre_set);
+
+ /* Enable interrupts and restore flags. */
+ spin_unlock_irqrestore(&lp->spinlock, flags);
+
+ return ret;
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Wireless Handler : get level threshold
+ */
+static int wavelan_get_sens(struct net_device *dev,
+ struct iw_request_info *info,
+ union iwreq_data *wrqu,
+ char *extra)
+{
+ unsigned long ioaddr = dev->base_addr;
+ net_local *lp = (net_local *) dev->priv; /* lp is not unused */
+ psa_t psa;
+ unsigned long flags;
+ int ret = 0;
+
+ /* Disable interrupts and save flags. */
+ spin_lock_irqsave(&lp->spinlock, flags);
+
+ /* Read the level threshold. */
+ psa_read(ioaddr, lp->hacr,
+ (char *) &psa.psa_thr_pre_set - (char *) &psa,
+ (unsigned char *) &psa.psa_thr_pre_set, 1);
+ wrqu->sens.value = psa.psa_thr_pre_set & 0x3F;
+ wrqu->sens.fixed = 1;
+
+ /* Enable interrupts and restore flags. */
+ spin_unlock_irqrestore(&lp->spinlock, flags);
+
+ return ret;
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Wireless Handler : set encryption key
+ */
+static int wavelan_set_encode(struct net_device *dev,
+ struct iw_request_info *info,
+ union iwreq_data *wrqu,
+ char *extra)
+{
+ unsigned long ioaddr = dev->base_addr;
+ net_local *lp = (net_local *) dev->priv; /* lp is not unused */
+ unsigned long flags;
+ psa_t psa;
+ int ret = 0;
+
+ /* Disable interrupts and save flags. */
+ spin_lock_irqsave(&lp->spinlock, flags);
+
+ /* Check if capable of encryption */
+ if (!mmc_encr(ioaddr)) {
+ ret = -EOPNOTSUPP;
+ }
+
+ /* Check the size of the key */
+ if((wrqu->encoding.length != 8) && (wrqu->encoding.length != 0)) {
+ ret = -EINVAL;
+ }
+
+ if(!ret) {
+ /* Basic checking... */
+ if (wrqu->encoding.length == 8) {
+ /* Copy the key in the driver */
+ memcpy(psa.psa_encryption_key, extra,
+ wrqu->encoding.length);
+ psa.psa_encryption_select = 1;
+
+ psa_write(ioaddr, lp->hacr,
+ (char *) &psa.psa_encryption_select -
+ (char *) &psa,
+ (unsigned char *) &psa.
+ psa_encryption_select, 8 + 1);
+
+ mmc_out(ioaddr, mmwoff(0, mmw_encr_enable),
+ MMW_ENCR_ENABLE_EN | MMW_ENCR_ENABLE_MODE);
+ mmc_write(ioaddr, mmwoff(0, mmw_encr_key),
+ (unsigned char *) &psa.
+ psa_encryption_key, 8);
+ }
+
+ /* disable encryption */
+ if (wrqu->encoding.flags & IW_ENCODE_DISABLED) {
+ psa.psa_encryption_select = 0;
+ psa_write(ioaddr, lp->hacr,
+ (char *) &psa.psa_encryption_select -
+ (char *) &psa,
+ (unsigned char *) &psa.
+ psa_encryption_select, 1);
+
+ mmc_out(ioaddr, mmwoff(0, mmw_encr_enable), 0);
+ }
+ /* update the Wavelan checksum */
+ update_psa_checksum(dev, ioaddr, lp->hacr);
+ }
+
+ /* Enable interrupts and restore flags. */
+ spin_unlock_irqrestore(&lp->spinlock, flags);
+
+ return ret;
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Wireless Handler : get encryption key
+ */
+static int wavelan_get_encode(struct net_device *dev,
+ struct iw_request_info *info,
+ union iwreq_data *wrqu,
+ char *extra)
+{
+ unsigned long ioaddr = dev->base_addr;
+ net_local *lp = (net_local *) dev->priv; /* lp is not unused */
+ psa_t psa;
+ unsigned long flags;
+ int ret = 0;
+
+ /* Disable interrupts and save flags. */
+ spin_lock_irqsave(&lp->spinlock, flags);
+
+ /* Check if encryption is available */
+ if (!mmc_encr(ioaddr)) {
+ ret = -EOPNOTSUPP;
+ } else {
+ /* Read the encryption key */
+ psa_read(ioaddr, lp->hacr,
+ (char *) &psa.psa_encryption_select -
+ (char *) &psa,
+ (unsigned char *) &psa.
+ psa_encryption_select, 1 + 8);
+
+ /* encryption is enabled ? */
+ if (psa.psa_encryption_select)
+ wrqu->encoding.flags = IW_ENCODE_ENABLED;
+ else
+ wrqu->encoding.flags = IW_ENCODE_DISABLED;
+ wrqu->encoding.flags |= mmc_encr(ioaddr);
+
+ /* Copy the key to the user buffer */
+ wrqu->encoding.length = 8;
+ memcpy(extra, psa.psa_encryption_key, wrqu->encoding.length);
+ }
+
+ /* Enable interrupts and restore flags. */
+ spin_unlock_irqrestore(&lp->spinlock, flags);
+
+ return ret;
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Wireless Handler : get range info
+ */
+static int wavelan_get_range(struct net_device *dev,
+ struct iw_request_info *info,
+ union iwreq_data *wrqu,
+ char *extra)
+{
+ unsigned long ioaddr = dev->base_addr;
+ net_local *lp = (net_local *) dev->priv; /* lp is not unused */
+ struct iw_range *range = (struct iw_range *) extra;
+ unsigned long flags;
+ int ret = 0;
+
+ /* Set the length (very important for backward compatibility) */
+ wrqu->data.length = sizeof(struct iw_range);
+
+ /* Set all the info we don't care or don't know about to zero */
+ memset(range, 0, sizeof(struct iw_range));
+
+ /* Set the Wireless Extension versions */
+ range->we_version_compiled = WIRELESS_EXT;
+ range->we_version_source = 9;
+
+ /* Set information in the range struct. */
+ range->throughput = 1.6 * 1000 * 1000; /* don't argue on this ! */
+ range->min_nwid = 0x0000;
+ range->max_nwid = 0xFFFF;
+
+ range->sensitivity = 0x3F;
+ range->max_qual.qual = MMR_SGNL_QUAL;
+ range->max_qual.level = MMR_SIGNAL_LVL;
+ range->max_qual.noise = MMR_SILENCE_LVL;
+ range->avg_qual.qual = MMR_SGNL_QUAL; /* Always max */
+ /* Need to get better values for those two */
+ range->avg_qual.level = 30;
+ range->avg_qual.noise = 8;
+
+ range->num_bitrates = 1;
+ range->bitrate[0] = 2000000; /* 2 Mb/s */
+
+ /* Event capability (kernel + driver) */
+ range->event_capa[0] = (IW_EVENT_CAPA_MASK(0x8B02) |
+ IW_EVENT_CAPA_MASK(0x8B04));
+ range->event_capa[1] = IW_EVENT_CAPA_K_1;
+
+ /* Disable interrupts and save flags. */
+ spin_lock_irqsave(&lp->spinlock, flags);
+
+ /* Attempt to recognise 2.00 cards (2.4 GHz frequency selectable). */
+ if (!(mmc_in(ioaddr, mmroff(0, mmr_fee_status)) &
+ (MMR_FEE_STATUS_DWLD | MMR_FEE_STATUS_BUSY))) {
+ range->num_channels = 10;
+ range->num_frequency = wv_frequency_list(ioaddr, range->freq,
+ IW_MAX_FREQUENCIES);
+ } else
+ range->num_channels = range->num_frequency = 0;
+
+ /* Encryption supported ? */
+ if (mmc_encr(ioaddr)) {
+ range->encoding_size[0] = 8; /* DES = 64 bits key */
+ range->num_encoding_sizes = 1;
+ range->max_encoding_tokens = 1; /* Only one key possible */
+ } else {
+ range->num_encoding_sizes = 0;
+ range->max_encoding_tokens = 0;
+ }
+
+ /* Enable interrupts and restore flags. */
+ spin_unlock_irqrestore(&lp->spinlock, flags);
+
+ return ret;
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Wireless Private Handler : set quality threshold
+ */
+static int wavelan_set_qthr(struct net_device *dev,
+ struct iw_request_info *info,
+ union iwreq_data *wrqu,
+ char *extra)
+{
+ unsigned long ioaddr = dev->base_addr;
+ net_local *lp = (net_local *) dev->priv; /* lp is not unused */
+ psa_t psa;
+ unsigned long flags;
+
+ /* Disable interrupts and save flags. */
+ spin_lock_irqsave(&lp->spinlock, flags);
+
+ psa.psa_quality_thr = *(extra) & 0x0F;
+ psa_write(ioaddr, lp->hacr,
+ (char *) &psa.psa_quality_thr - (char *) &psa,
+ (unsigned char *) &psa.psa_quality_thr, 1);
+ /* update the Wavelan checksum */
+ update_psa_checksum(dev, ioaddr, lp->hacr);
+ mmc_out(ioaddr, mmwoff(0, mmw_quality_thr),
+ psa.psa_quality_thr);
+
+ /* Enable interrupts and restore flags. */
+ spin_unlock_irqrestore(&lp->spinlock, flags);
+
+ return 0;
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Wireless Private Handler : get quality threshold
+ */
+static int wavelan_get_qthr(struct net_device *dev,
+ struct iw_request_info *info,
+ union iwreq_data *wrqu,
+ char *extra)
+{
+ unsigned long ioaddr = dev->base_addr;
+ net_local *lp = (net_local *) dev->priv; /* lp is not unused */
+ psa_t psa;
+ unsigned long flags;
+
+ /* Disable interrupts and save flags. */
+ spin_lock_irqsave(&lp->spinlock, flags);
+
+ psa_read(ioaddr, lp->hacr,
+ (char *) &psa.psa_quality_thr - (char *) &psa,
+ (unsigned char *) &psa.psa_quality_thr, 1);
+ *(extra) = psa.psa_quality_thr & 0x0F;
+
+ /* Enable interrupts and restore flags. */
+ spin_unlock_irqrestore(&lp->spinlock, flags);
+
+ return 0;
+}
+
+#ifdef HISTOGRAM
+/*------------------------------------------------------------------*/
+/*
+ * Wireless Private Handler : set histogram
+ */
+static int wavelan_set_histo(struct net_device *dev,
+ struct iw_request_info *info,
+ union iwreq_data *wrqu,
+ char *extra)
+{
+ net_local *lp = (net_local *) dev->priv; /* lp is not unused */
+
+ /* Check the number of intervals. */
+ if (wrqu->data.length > 16) {
+ return(-E2BIG);
+ }
+
+ /* Disable histo while we copy the addresses.
+ * As we don't disable interrupts, we need to do this */
+ lp->his_number = 0;
+
+ /* Are there ranges to copy? */
+ if (wrqu->data.length > 0) {
+ /* Copy interval ranges to the driver */
+ memcpy(lp->his_range, extra, wrqu->data.length);
+
+ {
+ int i;
+ printk(KERN_DEBUG "Histo :");
+ for(i = 0; i < wrqu->data.length; i++)
+ printk(" %d", lp->his_range[i]);
+ printk("\n");
+ }
+
+ /* Reset result structure. */
+ memset(lp->his_sum, 0x00, sizeof(long) * 16);
+ }
+
+ /* Now we can set the number of ranges */
+ lp->his_number = wrqu->data.length;
+
+ return(0);
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Wireless Private Handler : get histogram
+ */
+static int wavelan_get_histo(struct net_device *dev,
+ struct iw_request_info *info,
+ union iwreq_data *wrqu,
+ char *extra)
+{
+ net_local *lp = (net_local *) dev->priv; /* lp is not unused */
+
+ /* Set the number of intervals. */
+ wrqu->data.length = lp->his_number;
+
+ /* Give back the distribution statistics */
+ if(lp->his_number > 0)
+ memcpy(extra, lp->his_sum, sizeof(long) * lp->his_number);
+
+ return(0);
+}
+#endif /* HISTOGRAM */
+
+/*------------------------------------------------------------------*/
+/*
+ * Structures to export the Wireless Handlers
+ */
+
+static const iw_handler wavelan_handler[] =
+{
+ NULL, /* SIOCSIWNAME */
+ wavelan_get_name, /* SIOCGIWNAME */
+ wavelan_set_nwid, /* SIOCSIWNWID */
+ wavelan_get_nwid, /* SIOCGIWNWID */
+ wavelan_set_freq, /* SIOCSIWFREQ */
+ wavelan_get_freq, /* SIOCGIWFREQ */
+ NULL, /* SIOCSIWMODE */
+ NULL, /* SIOCGIWMODE */
+ wavelan_set_sens, /* SIOCSIWSENS */
+ wavelan_get_sens, /* SIOCGIWSENS */
+ NULL, /* SIOCSIWRANGE */
+ wavelan_get_range, /* SIOCGIWRANGE */
+ NULL, /* SIOCSIWPRIV */
+ NULL, /* SIOCGIWPRIV */
+ NULL, /* SIOCSIWSTATS */
+ NULL, /* SIOCGIWSTATS */
+ iw_handler_set_spy, /* SIOCSIWSPY */
+ iw_handler_get_spy, /* SIOCGIWSPY */
+ iw_handler_set_thrspy, /* SIOCSIWTHRSPY */
+ iw_handler_get_thrspy, /* SIOCGIWTHRSPY */
+ NULL, /* SIOCSIWAP */
+ NULL, /* SIOCGIWAP */
+ NULL, /* -- hole -- */
+ NULL, /* SIOCGIWAPLIST */
+ NULL, /* -- hole -- */
+ NULL, /* -- hole -- */
+ NULL, /* SIOCSIWESSID */
+ NULL, /* SIOCGIWESSID */
+ NULL, /* SIOCSIWNICKN */
+ NULL, /* SIOCGIWNICKN */
+ NULL, /* -- hole -- */
+ NULL, /* -- hole -- */
+ NULL, /* SIOCSIWRATE */
+ NULL, /* SIOCGIWRATE */
+ NULL, /* SIOCSIWRTS */
+ NULL, /* SIOCGIWRTS */
+ NULL, /* SIOCSIWFRAG */
+ NULL, /* SIOCGIWFRAG */
+ NULL, /* SIOCSIWTXPOW */
+ NULL, /* SIOCGIWTXPOW */
+ NULL, /* SIOCSIWRETRY */
+ NULL, /* SIOCGIWRETRY */
+ /* Bummer ! Why those are only at the end ??? */
+ wavelan_set_encode, /* SIOCSIWENCODE */
+ wavelan_get_encode, /* SIOCGIWENCODE */
+};
+
+static const iw_handler wavelan_private_handler[] =
+{
+ wavelan_set_qthr, /* SIOCIWFIRSTPRIV */
+ wavelan_get_qthr, /* SIOCIWFIRSTPRIV + 1 */
+#ifdef HISTOGRAM
+ wavelan_set_histo, /* SIOCIWFIRSTPRIV + 2 */
+ wavelan_get_histo, /* SIOCIWFIRSTPRIV + 3 */
+#endif /* HISTOGRAM */
+};
+
+static const struct iw_priv_args wavelan_private_args[] = {
+/*{ cmd, set_args, get_args, name } */
+ { SIOCSIPQTHR, IW_PRIV_TYPE_BYTE | IW_PRIV_SIZE_FIXED | 1, 0, "setqualthr" },
+ { SIOCGIPQTHR, 0, IW_PRIV_TYPE_BYTE | IW_PRIV_SIZE_FIXED | 1, "getqualthr" },
+ { SIOCSIPHISTO, IW_PRIV_TYPE_BYTE | 16, 0, "sethisto" },
+ { SIOCGIPHISTO, 0, IW_PRIV_TYPE_INT | 16, "gethisto" },
+};
+
+static const struct iw_handler_def wavelan_handler_def =
+{
+ .num_standard = sizeof(wavelan_handler)/sizeof(iw_handler),
+ .num_private = sizeof(wavelan_private_handler)/sizeof(iw_handler),
+ .num_private_args = sizeof(wavelan_private_args)/sizeof(struct iw_priv_args),
+ .standard = wavelan_handler,
+ .private = wavelan_private_handler,
+ .private_args = wavelan_private_args,
+ .get_wireless_stats = wavelan_get_wireless_stats,
+};
+
+/*------------------------------------------------------------------*/
+/*
+ * Get wireless statistics.
+ * Called by /proc/net/wireless
+ */
+static iw_stats *wavelan_get_wireless_stats(struct net_device * dev)
+{
+ unsigned long ioaddr = dev->base_addr;
+ net_local *lp = (net_local *) dev->priv;
+ mmr_t m;
+ iw_stats *wstats;
+ unsigned long flags;
+
+#ifdef DEBUG_IOCTL_TRACE
+ printk(KERN_DEBUG "%s: ->wavelan_get_wireless_stats()\n",
+ dev->name);
+#endif
+
+ /* Check */
+ if (lp == (net_local *) NULL)
+ return (iw_stats *) NULL;
+
+ /* Disable interrupts and save flags. */
+ spin_lock_irqsave(&lp->spinlock, flags);
+
+ wstats = &lp->wstats;
+
+ /* Get data from the mmc. */
+ mmc_out(ioaddr, mmwoff(0, mmw_freeze), 1);
+
+ mmc_read(ioaddr, mmroff(0, mmr_dce_status), &m.mmr_dce_status, 1);
+ mmc_read(ioaddr, mmroff(0, mmr_wrong_nwid_l), &m.mmr_wrong_nwid_l,
+ 2);
+ mmc_read(ioaddr, mmroff(0, mmr_thr_pre_set), &m.mmr_thr_pre_set,
+ 4);
+
+ mmc_out(ioaddr, mmwoff(0, mmw_freeze), 0);
+
+ /* Copy data to wireless stuff. */
+ wstats->status = m.mmr_dce_status & MMR_DCE_STATUS;
+ wstats->qual.qual = m.mmr_sgnl_qual & MMR_SGNL_QUAL;
+ wstats->qual.level = m.mmr_signal_lvl & MMR_SIGNAL_LVL;
+ wstats->qual.noise = m.mmr_silence_lvl & MMR_SILENCE_LVL;
+ wstats->qual.updated = (((m. mmr_signal_lvl & MMR_SIGNAL_LVL_VALID) >> 7)
+ | ((m.mmr_signal_lvl & MMR_SIGNAL_LVL_VALID) >> 6)
+ | ((m.mmr_silence_lvl & MMR_SILENCE_LVL_VALID) >> 5));
+ wstats->discard.nwid += (m.mmr_wrong_nwid_h << 8) | m.mmr_wrong_nwid_l;
+ wstats->discard.code = 0L;
+ wstats->discard.misc = 0L;
+
+ /* Enable interrupts and restore flags. */
+ spin_unlock_irqrestore(&lp->spinlock, flags);
+
+#ifdef DEBUG_IOCTL_TRACE
+ printk(KERN_DEBUG "%s: <-wavelan_get_wireless_stats()\n",
+ dev->name);
+#endif
+ return &lp->wstats;
+}
+#endif /* WIRELESS_EXT */
+
+/************************* PACKET RECEPTION *************************/
+/*
+ * This part deals with receiving the packets.
+ * The interrupt handler gets an interrupt when a packet has been
+ * successfully received and calls this part.
+ */
+
+/*------------------------------------------------------------------*/
+/*
+ * This routine does the actual copying of data (including the Ethernet
+ * header structure) from the WaveLAN card to an sk_buff chain that
+ * will be passed up to the network interface layer. NOTE: we
+ * currently don't handle trailer protocols (neither does the rest of
+ * the network interface), so if that is needed, it will (at least in
+ * part) be added here. The contents of the receive ring buffer are
+ * copied to a message chain that is then passed to the kernel.
+ *
+ * Note: if any errors occur, the packet is "dropped on the floor".
+ * (called by wv_packet_rcv())
+ */
+static inline void
+wv_packet_read(struct net_device * dev, u16 buf_off, int sksize)
+{
+ net_local *lp = (net_local *) dev->priv;
+ unsigned long ioaddr = dev->base_addr;
+ struct sk_buff *skb;
+
+#ifdef DEBUG_RX_TRACE
+ printk(KERN_DEBUG "%s: ->wv_packet_read(0x%X, %d)\n",
+ dev->name, buf_off, sksize);
+#endif
+
+ /* Allocate buffer for the data */
+ if ((skb = dev_alloc_skb(sksize)) == (struct sk_buff *) NULL) {
+#ifdef DEBUG_RX_ERROR
+ printk(KERN_INFO
+ "%s: wv_packet_read(): could not alloc_skb(%d, GFP_ATOMIC).\n",
+ dev->name, sksize);
+#endif
+ lp->stats.rx_dropped++;
+ return;
+ }
+
+ skb->dev = dev;
+
+ /* Copy the packet to the buffer. */
+ obram_read(ioaddr, buf_off, skb_put(skb, sksize), sksize);
+ skb->protocol = eth_type_trans(skb, dev);
+
+#ifdef DEBUG_RX_INFO
+ wv_packet_info(skb->mac.raw, sksize, dev->name, "wv_packet_read");
+#endif /* DEBUG_RX_INFO */
+
+ /* Statistics-gathering and associated stuff.
+ * It seem a bit messy with all the define, but it's really
+ * simple... */
+ if (
+#ifdef IW_WIRELESS_SPY /* defined in iw_handler.h */
+ (lp->spy_data.spy_number > 0) ||
+#endif /* IW_WIRELESS_SPY */
+#ifdef HISTOGRAM
+ (lp->his_number > 0) ||
+#endif /* HISTOGRAM */
+ 0) {
+ u8 stats[3]; /* signal level, noise level, signal quality */
+
+ /* Read signal level, silence level and signal quality bytes */
+ /* Note: in the PCMCIA hardware, these are part of the frame.
+ * It seems that for the ISA hardware, it's nowhere to be
+ * found in the frame, so I'm obliged to do this (it has a
+ * side effect on /proc/net/wireless).
+ * Any ideas?
+ */
+ mmc_out(ioaddr, mmwoff(0, mmw_freeze), 1);
+ mmc_read(ioaddr, mmroff(0, mmr_signal_lvl), stats, 3);
+ mmc_out(ioaddr, mmwoff(0, mmw_freeze), 0);
+
+#ifdef DEBUG_RX_INFO
+ printk(KERN_DEBUG
+ "%s: wv_packet_read(): Signal level %d/63, Silence level %d/63, signal quality %d/16\n",
+ dev->name, stats[0] & 0x3F, stats[1] & 0x3F,
+ stats[2] & 0x0F);
+#endif
+
+ /* Spying stuff */
+#ifdef IW_WIRELESS_SPY
+ wl_spy_gather(dev, skb->mac.raw + WAVELAN_ADDR_SIZE,
+ stats);
+#endif /* IW_WIRELESS_SPY */
+#ifdef HISTOGRAM
+ wl_his_gather(dev, stats);
+#endif /* HISTOGRAM */
+ }
+
+ /*
+ * Hand the packet to the network module.
+ */
+ netif_rx(skb);
+
+ /* Keep statistics up to date */
+ dev->last_rx = jiffies;
+ lp->stats.rx_packets++;
+ lp->stats.rx_bytes += sksize;
+
+#ifdef DEBUG_RX_TRACE
+ printk(KERN_DEBUG "%s: <-wv_packet_read()\n", dev->name);
+#endif
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Transfer as many packets as we can
+ * from the device RAM.
+ * (called in wavelan_interrupt()).
+ * Note : the spinlock is already grabbed for us.
+ */
+static inline void wv_receive(struct net_device * dev)
+{
+ unsigned long ioaddr = dev->base_addr;
+ net_local *lp = (net_local *) dev->priv;
+ fd_t fd;
+ rbd_t rbd;
+ int nreaped = 0;
+
+#ifdef DEBUG_RX_TRACE
+ printk(KERN_DEBUG "%s: ->wv_receive()\n", dev->name);
+#endif
+
+ /* Loop on each received packet. */
+ for (;;) {
+ obram_read(ioaddr, lp->rx_head, (unsigned char *) &fd,
+ sizeof(fd));
+
+ /* Note about the status :
+ * It start up to be 0 (the value we set). Then, when the RU
+ * grab the buffer to prepare for reception, it sets the
+ * FD_STATUS_B flag. When the RU has finished receiving the
+ * frame, it clears FD_STATUS_B, set FD_STATUS_C to indicate
+ * completion and set the other flags to indicate the eventual
+ * errors. FD_STATUS_OK indicates that the reception was OK.
+ */
+
+ /* If the current frame is not complete, we have reached the end. */
+ if ((fd.fd_status & FD_STATUS_C) != FD_STATUS_C)
+ break; /* This is how we exit the loop. */
+
+ nreaped++;
+
+ /* Check whether frame was correctly received. */
+ if ((fd.fd_status & FD_STATUS_OK) == FD_STATUS_OK) {
+ /* Does the frame contain a pointer to the data? Let's check. */
+ if (fd.fd_rbd_offset != I82586NULL) {
+ /* Read the receive buffer descriptor */
+ obram_read(ioaddr, fd.fd_rbd_offset,
+ (unsigned char *) &rbd,
+ sizeof(rbd));
+
+#ifdef DEBUG_RX_ERROR
+ if ((rbd.rbd_status & RBD_STATUS_EOF) !=
+ RBD_STATUS_EOF) printk(KERN_INFO
+ "%s: wv_receive(): missing EOF flag.\n",
+ dev->name);
+
+ if ((rbd.rbd_status & RBD_STATUS_F) !=
+ RBD_STATUS_F) printk(KERN_INFO
+ "%s: wv_receive(): missing F flag.\n",
+ dev->name);
+#endif /* DEBUG_RX_ERROR */
+
+ /* Read the packet and transmit to Linux */
+ wv_packet_read(dev, rbd.rbd_bufl,
+ rbd.
+ rbd_status &
+ RBD_STATUS_ACNT);
+ }
+#ifdef DEBUG_RX_ERROR
+ else /* if frame has no data */
+ printk(KERN_INFO
+ "%s: wv_receive(): frame has no data.\n",
+ dev->name);
+#endif
+ } else { /* If reception was no successful */
+
+ lp->stats.rx_errors++;
+
+#ifdef DEBUG_RX_INFO
+ printk(KERN_DEBUG
+ "%s: wv_receive(): frame not received successfully (%X).\n",
+ dev->name, fd.fd_status);
+#endif
+
+#ifdef DEBUG_RX_ERROR
+ if ((fd.fd_status & FD_STATUS_S6) != 0)
+ printk(KERN_INFO
+ "%s: wv_receive(): no EOF flag.\n",
+ dev->name);
+#endif
+
+ if ((fd.fd_status & FD_STATUS_S7) != 0) {
+ lp->stats.rx_length_errors++;
+#ifdef DEBUG_RX_FAIL
+ printk(KERN_DEBUG
+ "%s: wv_receive(): frame too short.\n",
+ dev->name);
+#endif
+ }
+
+ if ((fd.fd_status & FD_STATUS_S8) != 0) {
+ lp->stats.rx_over_errors++;
+#ifdef DEBUG_RX_FAIL
+ printk(KERN_DEBUG
+ "%s: wv_receive(): rx DMA overrun.\n",
+ dev->name);
+#endif
+ }
+
+ if ((fd.fd_status & FD_STATUS_S9) != 0) {
+ lp->stats.rx_fifo_errors++;
+#ifdef DEBUG_RX_FAIL
+ printk(KERN_DEBUG
+ "%s: wv_receive(): ran out of resources.\n",
+ dev->name);
+#endif
+ }
+
+ if ((fd.fd_status & FD_STATUS_S10) != 0) {
+ lp->stats.rx_frame_errors++;
+#ifdef DEBUG_RX_FAIL
+ printk(KERN_DEBUG
+ "%s: wv_receive(): alignment error.\n",
+ dev->name);
+#endif
+ }
+
+ if ((fd.fd_status & FD_STATUS_S11) != 0) {
+ lp->stats.rx_crc_errors++;
+#ifdef DEBUG_RX_FAIL
+ printk(KERN_DEBUG
+ "%s: wv_receive(): CRC error.\n",
+ dev->name);
+#endif
+ }
+ }
+
+ fd.fd_status = 0;
+ obram_write(ioaddr, fdoff(lp->rx_head, fd_status),
+ (unsigned char *) &fd.fd_status,
+ sizeof(fd.fd_status));
+
+ fd.fd_command = FD_COMMAND_EL;
+ obram_write(ioaddr, fdoff(lp->rx_head, fd_command),
+ (unsigned char *) &fd.fd_command,
+ sizeof(fd.fd_command));
+
+ fd.fd_command = 0;
+ obram_write(ioaddr, fdoff(lp->rx_last, fd_command),
+ (unsigned char *) &fd.fd_command,
+ sizeof(fd.fd_command));
+
+ lp->rx_last = lp->rx_head;
+ lp->rx_head = fd.fd_link_offset;
+ } /* for(;;) -> loop on all frames */
+
+#ifdef DEBUG_RX_INFO
+ if (nreaped > 1)
+ printk(KERN_DEBUG "%s: wv_receive(): reaped %d\n",
+ dev->name, nreaped);
+#endif
+#ifdef DEBUG_RX_TRACE
+ printk(KERN_DEBUG "%s: <-wv_receive()\n", dev->name);
+#endif
+}
+
+/*********************** PACKET TRANSMISSION ***********************/
+/*
+ * This part deals with sending packets through the WaveLAN.
+ *
+ */
+
+/*------------------------------------------------------------------*/
+/*
+ * This routine fills in the appropriate registers and memory
+ * locations on the WaveLAN card and starts the card off on
+ * the transmit.
+ *
+ * The principle:
+ * Each block contains a transmit command, a NOP command,
+ * a transmit block descriptor and a buffer.
+ * The CU read the transmit block which point to the tbd,
+ * read the tbd and the content of the buffer.
+ * When it has finish with it, it goes to the next command
+ * which in our case is the NOP. The NOP points on itself,
+ * so the CU stop here.
+ * When we add the next block, we modify the previous nop
+ * to make it point on the new tx command.
+ * Simple, isn't it ?
+ *
+ * (called in wavelan_packet_xmit())
+ */
+static inline int wv_packet_write(struct net_device * dev, void *buf, short length)
+{
+ net_local *lp = (net_local *) dev->priv;
+ unsigned long ioaddr = dev->base_addr;
+ unsigned short txblock;
+ unsigned short txpred;
+ unsigned short tx_addr;
+ unsigned short nop_addr;
+ unsigned short tbd_addr;
+ unsigned short buf_addr;
+ ac_tx_t tx;
+ ac_nop_t nop;
+ tbd_t tbd;
+ int clen = length;
+ unsigned long flags;
+
+#ifdef DEBUG_TX_TRACE
+ printk(KERN_DEBUG "%s: ->wv_packet_write(%d)\n", dev->name,
+ length);
+#endif
+
+ spin_lock_irqsave(&lp->spinlock, flags);
+
+ /* Check nothing bad has happened */
+ if (lp->tx_n_in_use == (NTXBLOCKS - 1)) {
+#ifdef DEBUG_TX_ERROR
+ printk(KERN_INFO "%s: wv_packet_write(): Tx queue full.\n",
+ dev->name);
+#endif
+ spin_unlock_irqrestore(&lp->spinlock, flags);
+ return 1;
+ }
+
+ /* Calculate addresses of next block and previous block. */
+ txblock = lp->tx_first_free;
+ txpred = txblock - TXBLOCKZ;
+ if (txpred < OFFSET_CU)
+ txpred += NTXBLOCKS * TXBLOCKZ;
+ lp->tx_first_free += TXBLOCKZ;
+ if (lp->tx_first_free >= OFFSET_CU + NTXBLOCKS * TXBLOCKZ)
+ lp->tx_first_free -= NTXBLOCKS * TXBLOCKZ;
+
+ lp->tx_n_in_use++;
+
+ /* Calculate addresses of the different parts of the block. */
+ tx_addr = txblock;
+ nop_addr = tx_addr + sizeof(tx);
+ tbd_addr = nop_addr + sizeof(nop);
+ buf_addr = tbd_addr + sizeof(tbd);
+
+ /*
+ * Transmit command
+ */
+ tx.tx_h.ac_status = 0;
+ obram_write(ioaddr, toff(ac_tx_t, tx_addr, tx_h.ac_status),
+ (unsigned char *) &tx.tx_h.ac_status,
+ sizeof(tx.tx_h.ac_status));
+
+ /*
+ * NOP command
+ */
+ nop.nop_h.ac_status = 0;
+ obram_write(ioaddr, toff(ac_nop_t, nop_addr, nop_h.ac_status),
+ (unsigned char *) &nop.nop_h.ac_status,
+ sizeof(nop.nop_h.ac_status));
+ nop.nop_h.ac_link = nop_addr;
+ obram_write(ioaddr, toff(ac_nop_t, nop_addr, nop_h.ac_link),
+ (unsigned char *) &nop.nop_h.ac_link,
+ sizeof(nop.nop_h.ac_link));
+
+ /*
+ * Transmit buffer descriptor
+ */
+ tbd.tbd_status = TBD_STATUS_EOF | (TBD_STATUS_ACNT & clen);
+ tbd.tbd_next_bd_offset = I82586NULL;
+ tbd.tbd_bufl = buf_addr;
+ tbd.tbd_bufh = 0;
+ obram_write(ioaddr, tbd_addr, (unsigned char *) &tbd, sizeof(tbd));
+
+ /*
+ * Data
+ */
+ obram_write(ioaddr, buf_addr, buf, length);
+
+ /*
+ * Overwrite the predecessor NOP link
+ * so that it points to this txblock.
+ */
+ nop_addr = txpred + sizeof(tx);
+ nop.nop_h.ac_status = 0;
+ obram_write(ioaddr, toff(ac_nop_t, nop_addr, nop_h.ac_status),
+ (unsigned char *) &nop.nop_h.ac_status,
+ sizeof(nop.nop_h.ac_status));
+ nop.nop_h.ac_link = txblock;
+ obram_write(ioaddr, toff(ac_nop_t, nop_addr, nop_h.ac_link),
+ (unsigned char *) &nop.nop_h.ac_link,
+ sizeof(nop.nop_h.ac_link));
+
+ /* Make sure the watchdog will keep quiet for a while */
+ dev->trans_start = jiffies;
+
+ /* Keep stats up to date. */
+ lp->stats.tx_bytes += length;
+
+ if (lp->tx_first_in_use == I82586NULL)
+ lp->tx_first_in_use = txblock;
+
+ if (lp->tx_n_in_use < NTXBLOCKS - 1)
+ netif_wake_queue(dev);
+
+ spin_unlock_irqrestore(&lp->spinlock, flags);
+
+#ifdef DEBUG_TX_INFO
+ wv_packet_info((u8 *) buf, length, dev->name,
+ "wv_packet_write");
+#endif /* DEBUG_TX_INFO */
+
+#ifdef DEBUG_TX_TRACE
+ printk(KERN_DEBUG "%s: <-wv_packet_write()\n", dev->name);
+#endif
+
+ return 0;
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * This routine is called when we want to send a packet (NET3 callback)
+ * In this routine, we check if the harware is ready to accept
+ * the packet. We also prevent reentrance. Then we call the function
+ * to send the packet.
+ */
+static int wavelan_packet_xmit(struct sk_buff *skb, struct net_device * dev)
+{
+ net_local *lp = (net_local *) dev->priv;
+ unsigned long flags;
+
+#ifdef DEBUG_TX_TRACE
+ printk(KERN_DEBUG "%s: ->wavelan_packet_xmit(0x%X)\n", dev->name,
+ (unsigned) skb);
+#endif
+
+ /*
+ * Block a timer-based transmit from overlapping.
+ * In other words, prevent reentering this routine.
+ */
+ netif_stop_queue(dev);
+
+ /* If somebody has asked to reconfigure the controller,
+ * we can do it now.
+ */
+ if (lp->reconfig_82586) {
+ spin_lock_irqsave(&lp->spinlock, flags);
+ wv_82586_config(dev);
+ spin_unlock_irqrestore(&lp->spinlock, flags);
+ /* Check that we can continue */
+ if (lp->tx_n_in_use == (NTXBLOCKS - 1))
+ return 1;
+ }
+#ifdef DEBUG_TX_ERROR
+ if (skb->next)
+ printk(KERN_INFO "skb has next\n");
+#endif
+
+ /* Do we need some padding? */
+ /* Note : on wireless the propagation time is in the order of 1us,
+ * and we don't have the Ethernet specific requirement of beeing
+ * able to detect collisions, therefore in theory we don't really
+ * need to pad. Jean II */
+ if (skb->len < ETH_ZLEN) {
+ skb = skb_padto(skb, ETH_ZLEN);
+ if (skb == NULL)
+ return 0;
+ }
+
+ /* Write packet on the card */
+ if(wv_packet_write(dev, skb->data, skb->len))
+ return 1; /* We failed */
+
+ dev_kfree_skb(skb);
+
+#ifdef DEBUG_TX_TRACE
+ printk(KERN_DEBUG "%s: <-wavelan_packet_xmit()\n", dev->name);
+#endif
+ return 0;
+}
+
+/*********************** HARDWARE CONFIGURATION ***********************/
+/*
+ * This part does the real job of starting and configuring the hardware.
+ */
+
+/*--------------------------------------------------------------------*/
+/*
+ * Routine to initialize the Modem Management Controller.
+ * (called by wv_hw_reset())
+ */
+static inline int wv_mmc_init(struct net_device * dev)
+{
+ unsigned long ioaddr = dev->base_addr;
+ net_local *lp = (net_local *) dev->priv;
+ psa_t psa;
+ mmw_t m;
+ int configured;
+
+#ifdef DEBUG_CONFIG_TRACE
+ printk(KERN_DEBUG "%s: ->wv_mmc_init()\n", dev->name);
+#endif
+
+ /* Read the parameter storage area. */
+ psa_read(ioaddr, lp->hacr, 0, (unsigned char *) &psa, sizeof(psa));
+
+#ifdef USE_PSA_CONFIG
+ configured = psa.psa_conf_status & 1;
+#else
+ configured = 0;
+#endif
+
+ /* Is the PSA is not configured */
+ if (!configured) {
+ /* User will be able to configure NWID later (with iwconfig). */
+ psa.psa_nwid[0] = 0;
+ psa.psa_nwid[1] = 0;
+
+ /* no NWID checking since NWID is not set */
+ psa.psa_nwid_select = 0;
+
+ /* Disable encryption */
+ psa.psa_encryption_select = 0;
+
+ /* Set to standard values:
+ * 0x04 for AT,
+ * 0x01 for MCA,
+ * 0x04 for PCMCIA and 2.00 card (AT&T 407-024689/E document)
+ */
+ if (psa.psa_comp_number & 1)
+ psa.psa_thr_pre_set = 0x01;
+ else
+ psa.psa_thr_pre_set = 0x04;
+ psa.psa_quality_thr = 0x03;
+
+ /* It is configured */
+ psa.psa_conf_status |= 1;
+
+#ifdef USE_PSA_CONFIG
+ /* Write the psa. */
+ psa_write(ioaddr, lp->hacr,
+ (char *) psa.psa_nwid - (char *) &psa,
+ (unsigned char *) psa.psa_nwid, 4);
+ psa_write(ioaddr, lp->hacr,
+ (char *) &psa.psa_thr_pre_set - (char *) &psa,
+ (unsigned char *) &psa.psa_thr_pre_set, 1);
+ psa_write(ioaddr, lp->hacr,
+ (char *) &psa.psa_quality_thr - (char *) &psa,
+ (unsigned char *) &psa.psa_quality_thr, 1);
+ psa_write(ioaddr, lp->hacr,
+ (char *) &psa.psa_conf_status - (char *) &psa,
+ (unsigned char *) &psa.psa_conf_status, 1);
+ /* update the Wavelan checksum */
+ update_psa_checksum(dev, ioaddr, lp->hacr);
+#endif
+ }
+
+ /* Zero the mmc structure. */
+ memset(&m, 0x00, sizeof(m));
+
+ /* Copy PSA info to the mmc. */
+ m.mmw_netw_id_l = psa.psa_nwid[1];
+ m.mmw_netw_id_h = psa.psa_nwid[0];
+
+ if (psa.psa_nwid_select & 1)
+ m.mmw_loopt_sel = 0x00;
+ else
+ m.mmw_loopt_sel = MMW_LOOPT_SEL_DIS_NWID;
+
+ memcpy(&m.mmw_encr_key, &psa.psa_encryption_key,
+ sizeof(m.mmw_encr_key));
+
+ if (psa.psa_encryption_select)
+ m.mmw_encr_enable =
+ MMW_ENCR_ENABLE_EN | MMW_ENCR_ENABLE_MODE;
+ else
+ m.mmw_encr_enable = 0;
+
+ m.mmw_thr_pre_set = psa.psa_thr_pre_set & 0x3F;
+ m.mmw_quality_thr = psa.psa_quality_thr & 0x0F;
+
+ /*
+ * Set default modem control parameters.
+ * See NCR document 407-0024326 Rev. A.
+ */
+ m.mmw_jabber_enable = 0x01;
+ m.mmw_freeze = 0;
+ m.mmw_anten_sel = MMW_ANTEN_SEL_ALG_EN;
+ m.mmw_ifs = 0x20;
+ m.mmw_mod_delay = 0x04;
+ m.mmw_jam_time = 0x38;
+
+ m.mmw_des_io_invert = 0;
+ m.mmw_decay_prm = 0;
+ m.mmw_decay_updat_prm = 0;
+
+ /* Write all info to MMC. */
+ mmc_write(ioaddr, 0, (u8 *) & m, sizeof(m));
+
+ /* The following code starts the modem of the 2.00 frequency
+ * selectable cards at power on. It's not strictly needed for the
+ * following boots.
+ * The original patch was by Joe Finney for the PCMCIA driver, but
+ * I've cleaned it up a bit and added documentation.
+ * Thanks to Loeke Brederveld from Lucent for the info.
+ */
+
+ /* Attempt to recognise 2.00 cards (2.4 GHz frequency selectable)
+ * Does it work for everybody, especially old cards? */
+ /* Note: WFREQSEL verifies that it is able to read a sensible
+ * frequency from EEPROM (address 0x00) and that MMR_FEE_STATUS_ID
+ * is 0xA (Xilinx version) or 0xB (Ariadne version).
+ * My test is more crude but does work. */
+ if (!(mmc_in(ioaddr, mmroff(0, mmr_fee_status)) &
+ (MMR_FEE_STATUS_DWLD | MMR_FEE_STATUS_BUSY))) {
+ /* We must download the frequency parameters to the
+ * synthesizers (from the EEPROM - area 1)
+ * Note: as the EEPROM is automatically decremented, we set the end
+ * if the area... */
+ m.mmw_fee_addr = 0x0F;
+ m.mmw_fee_ctrl = MMW_FEE_CTRL_READ | MMW_FEE_CTRL_DWLD;
+ mmc_write(ioaddr, (char *) &m.mmw_fee_ctrl - (char *) &m,
+ (unsigned char *) &m.mmw_fee_ctrl, 2);
+
+ /* Wait until the download is finished. */
+ fee_wait(ioaddr, 100, 100);
+
+#ifdef DEBUG_CONFIG_INFO
+ /* The frequency was in the last word downloaded. */
+ mmc_read(ioaddr, (char *) &m.mmw_fee_data_l - (char *) &m,
+ (unsigned char *) &m.mmw_fee_data_l, 2);
+
+ /* Print some info for the user. */
+ printk(KERN_DEBUG
+ "%s: WaveLAN 2.00 recognised (frequency select). Current frequency = %ld\n",
+ dev->name,
+ ((m.
+ mmw_fee_data_h << 4) | (m.mmw_fee_data_l >> 4)) *
+ 5 / 2 + 24000L);
+#endif
+
+ /* We must now download the power adjust value (gain) to
+ * the synthesizers (from the EEPROM - area 7 - DAC). */
+ m.mmw_fee_addr = 0x61;
+ m.mmw_fee_ctrl = MMW_FEE_CTRL_READ | MMW_FEE_CTRL_DWLD;
+ mmc_write(ioaddr, (char *) &m.mmw_fee_ctrl - (char *) &m,
+ (unsigned char *) &m.mmw_fee_ctrl, 2);
+
+ /* Wait until the download is finished. */
+ }
+ /* if 2.00 card */
+#ifdef DEBUG_CONFIG_TRACE
+ printk(KERN_DEBUG "%s: <-wv_mmc_init()\n", dev->name);
+#endif
+ return 0;
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Construct the fd and rbd structures.
+ * Start the receive unit.
+ * (called by wv_hw_reset())
+ */
+static inline int wv_ru_start(struct net_device * dev)
+{
+ net_local *lp = (net_local *) dev->priv;
+ unsigned long ioaddr = dev->base_addr;
+ u16 scb_cs;
+ fd_t fd;
+ rbd_t rbd;
+ u16 rx;
+ u16 rx_next;
+ int i;
+
+#ifdef DEBUG_CONFIG_TRACE
+ printk(KERN_DEBUG "%s: ->wv_ru_start()\n", dev->name);
+#endif
+
+ obram_read(ioaddr, scboff(OFFSET_SCB, scb_status),
+ (unsigned char *) &scb_cs, sizeof(scb_cs));
+ if ((scb_cs & SCB_ST_RUS) == SCB_ST_RUS_RDY)
+ return 0;
+
+ lp->rx_head = OFFSET_RU;
+
+ for (i = 0, rx = lp->rx_head; i < NRXBLOCKS; i++, rx = rx_next) {
+ rx_next =
+ (i == NRXBLOCKS - 1) ? lp->rx_head : rx + RXBLOCKZ;
+
+ fd.fd_status = 0;
+ fd.fd_command = (i == NRXBLOCKS - 1) ? FD_COMMAND_EL : 0;
+ fd.fd_link_offset = rx_next;
+ fd.fd_rbd_offset = rx + sizeof(fd);
+ obram_write(ioaddr, rx, (unsigned char *) &fd, sizeof(fd));
+
+ rbd.rbd_status = 0;
+ rbd.rbd_next_rbd_offset = I82586NULL;
+ rbd.rbd_bufl = rx + sizeof(fd) + sizeof(rbd);
+ rbd.rbd_bufh = 0;
+ rbd.rbd_el_size = RBD_EL | (RBD_SIZE & MAXDATAZ);
+ obram_write(ioaddr, rx + sizeof(fd),
+ (unsigned char *) &rbd, sizeof(rbd));
+
+ lp->rx_last = rx;
+ }
+
+ obram_write(ioaddr, scboff(OFFSET_SCB, scb_rfa_offset),
+ (unsigned char *) &lp->rx_head, sizeof(lp->rx_head));
+
+ scb_cs = SCB_CMD_RUC_GO;
+ obram_write(ioaddr, scboff(OFFSET_SCB, scb_command),
+ (unsigned char *) &scb_cs, sizeof(scb_cs));
+
+ set_chan_attn(ioaddr, lp->hacr);
+
+ for (i = 1000; i > 0; i--) {
+ obram_read(ioaddr, scboff(OFFSET_SCB, scb_command),
+ (unsigned char *) &scb_cs, sizeof(scb_cs));
+ if (scb_cs == 0)
+ break;
+
+ udelay(10);
+ }
+
+ if (i <= 0) {
+#ifdef DEBUG_CONFIG_ERROR
+ printk(KERN_INFO
+ "%s: wavelan_ru_start(): board not accepting command.\n",
+ dev->name);
+#endif
+ return -1;
+ }
+#ifdef DEBUG_CONFIG_TRACE
+ printk(KERN_DEBUG "%s: <-wv_ru_start()\n", dev->name);
+#endif
+ return 0;
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Initialise the transmit blocks.
+ * Start the command unit executing the NOP
+ * self-loop of the first transmit block.
+ *
+ * Here we create the list of send buffers used to transmit packets
+ * between the PC and the command unit. For each buffer, we create a
+ * buffer descriptor (pointing on the buffer), a transmit command
+ * (pointing to the buffer descriptor) and a NOP command.
+ * The transmit command is linked to the NOP, and the NOP to itself.
+ * When we will have finished executing the transmit command, we will
+ * then loop on the NOP. By releasing the NOP link to a new command,
+ * we may send another buffer.
+ *
+ * (called by wv_hw_reset())
+ */
+static inline int wv_cu_start(struct net_device * dev)
+{
+ net_local *lp = (net_local *) dev->priv;
+ unsigned long ioaddr = dev->base_addr;
+ int i;
+ u16 txblock;
+ u16 first_nop;
+ u16 scb_cs;
+
+#ifdef DEBUG_CONFIG_TRACE
+ printk(KERN_DEBUG "%s: ->wv_cu_start()\n", dev->name);
+#endif
+
+ lp->tx_first_free = OFFSET_CU;
+ lp->tx_first_in_use = I82586NULL;
+
+ for (i = 0, txblock = OFFSET_CU;
+ i < NTXBLOCKS; i++, txblock += TXBLOCKZ) {
+ ac_tx_t tx;
+ ac_nop_t nop;
+ tbd_t tbd;
+ unsigned short tx_addr;
+ unsigned short nop_addr;
+ unsigned short tbd_addr;
+ unsigned short buf_addr;
+
+ tx_addr = txblock;
+ nop_addr = tx_addr + sizeof(tx);
+ tbd_addr = nop_addr + sizeof(nop);
+ buf_addr = tbd_addr + sizeof(tbd);
+
+ tx.tx_h.ac_status = 0;
+ tx.tx_h.ac_command = acmd_transmit | AC_CFLD_I;
+ tx.tx_h.ac_link = nop_addr;
+ tx.tx_tbd_offset = tbd_addr;
+ obram_write(ioaddr, tx_addr, (unsigned char *) &tx,
+ sizeof(tx));
+
+ nop.nop_h.ac_status = 0;
+ nop.nop_h.ac_command = acmd_nop;
+ nop.nop_h.ac_link = nop_addr;
+ obram_write(ioaddr, nop_addr, (unsigned char *) &nop,
+ sizeof(nop));
+
+ tbd.tbd_status = TBD_STATUS_EOF;
+ tbd.tbd_next_bd_offset = I82586NULL;
+ tbd.tbd_bufl = buf_addr;
+ tbd.tbd_bufh = 0;
+ obram_write(ioaddr, tbd_addr, (unsigned char *) &tbd,
+ sizeof(tbd));
+ }
+
+ first_nop =
+ OFFSET_CU + (NTXBLOCKS - 1) * TXBLOCKZ + sizeof(ac_tx_t);
+ obram_write(ioaddr, scboff(OFFSET_SCB, scb_cbl_offset),
+ (unsigned char *) &first_nop, sizeof(first_nop));
+
+ scb_cs = SCB_CMD_CUC_GO;
+ obram_write(ioaddr, scboff(OFFSET_SCB, scb_command),
+ (unsigned char *) &scb_cs, sizeof(scb_cs));
+
+ set_chan_attn(ioaddr, lp->hacr);
+
+ for (i = 1000; i > 0; i--) {
+ obram_read(ioaddr, scboff(OFFSET_SCB, scb_command),
+ (unsigned char *) &scb_cs, sizeof(scb_cs));
+ if (scb_cs == 0)
+ break;
+
+ udelay(10);
+ }
+
+ if (i <= 0) {
+#ifdef DEBUG_CONFIG_ERROR
+ printk(KERN_INFO
+ "%s: wavelan_cu_start(): board not accepting command.\n",
+ dev->name);
+#endif
+ return -1;
+ }
+
+ lp->tx_n_in_use = 0;
+ netif_start_queue(dev);
+#ifdef DEBUG_CONFIG_TRACE
+ printk(KERN_DEBUG "%s: <-wv_cu_start()\n", dev->name);
+#endif
+ return 0;
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * This routine does a standard configuration of the WaveLAN
+ * controller (i82586).
+ *
+ * It initialises the scp, iscp and scb structure
+ * The first two are just pointers to the next.
+ * The last one is used for basic configuration and for basic
+ * communication (interrupt status).
+ *
+ * (called by wv_hw_reset())
+ */
+static inline int wv_82586_start(struct net_device * dev)
+{
+ net_local *lp = (net_local *) dev->priv;
+ unsigned long ioaddr = dev->base_addr;
+ scp_t scp; /* system configuration pointer */
+ iscp_t iscp; /* intermediate scp */
+ scb_t scb; /* system control block */
+ ach_t cb; /* Action command header */
+ u8 zeroes[512];
+ int i;
+
+#ifdef DEBUG_CONFIG_TRACE
+ printk(KERN_DEBUG "%s: ->wv_82586_start()\n", dev->name);
+#endif
+
+ /*
+ * Clear the onboard RAM.
+ */
+ memset(&zeroes[0], 0x00, sizeof(zeroes));
+ for (i = 0; i < I82586_MEMZ; i += sizeof(zeroes))
+ obram_write(ioaddr, i, &zeroes[0], sizeof(zeroes));
+
+ /*
+ * Construct the command unit structures:
+ * scp, iscp, scb, cb.
+ */
+ memset(&scp, 0x00, sizeof(scp));
+ scp.scp_sysbus = SCP_SY_16BBUS;
+ scp.scp_iscpl = OFFSET_ISCP;
+ obram_write(ioaddr, OFFSET_SCP, (unsigned char *) &scp,
+ sizeof(scp));
+
+ memset(&iscp, 0x00, sizeof(iscp));
+ iscp.iscp_busy = 1;
+ iscp.iscp_offset = OFFSET_SCB;
+ obram_write(ioaddr, OFFSET_ISCP, (unsigned char *) &iscp,
+ sizeof(iscp));
+
+ /* Our first command is to reset the i82586. */
+ memset(&scb, 0x00, sizeof(scb));
+ scb.scb_command = SCB_CMD_RESET;
+ scb.scb_cbl_offset = OFFSET_CU;
+ scb.scb_rfa_offset = OFFSET_RU;
+ obram_write(ioaddr, OFFSET_SCB, (unsigned char *) &scb,
+ sizeof(scb));
+
+ set_chan_attn(ioaddr, lp->hacr);
+
+ /* Wait for command to finish. */
+ for (i = 1000; i > 0; i--) {
+ obram_read(ioaddr, OFFSET_ISCP, (unsigned char *) &iscp,
+ sizeof(iscp));
+
+ if (iscp.iscp_busy == (unsigned short) 0)
+ break;
+
+ udelay(10);
+ }
+
+ if (i <= 0) {
+#ifdef DEBUG_CONFIG_ERROR
+ printk(KERN_INFO
+ "%s: wv_82586_start(): iscp_busy timeout.\n",
+ dev->name);
+#endif
+ return -1;
+ }
+
+ /* Check command completion. */
+ for (i = 15; i > 0; i--) {
+ obram_read(ioaddr, OFFSET_SCB, (unsigned char *) &scb,
+ sizeof(scb));
+
+ if (scb.scb_status == (SCB_ST_CX | SCB_ST_CNA))
+ break;
+
+ udelay(10);
+ }
+
+ if (i <= 0) {
+#ifdef DEBUG_CONFIG_ERROR
+ printk(KERN_INFO
+ "%s: wv_82586_start(): status: expected 0x%02x, got 0x%02x.\n",
+ dev->name, SCB_ST_CX | SCB_ST_CNA, scb.scb_status);
+#endif
+ return -1;
+ }
+
+ wv_ack(dev);
+
+ /* Set the action command header. */
+ memset(&cb, 0x00, sizeof(cb));
+ cb.ac_command = AC_CFLD_EL | (AC_CFLD_CMD & acmd_diagnose);
+ cb.ac_link = OFFSET_CU;
+ obram_write(ioaddr, OFFSET_CU, (unsigned char *) &cb, sizeof(cb));
+
+ if (wv_synchronous_cmd(dev, "diag()") == -1)
+ return -1;
+
+ obram_read(ioaddr, OFFSET_CU, (unsigned char *) &cb, sizeof(cb));
+ if (cb.ac_status & AC_SFLD_FAIL) {
+#ifdef DEBUG_CONFIG_ERROR
+ printk(KERN_INFO
+ "%s: wv_82586_start(): i82586 Self Test failed.\n",
+ dev->name);
+#endif
+ return -1;
+ }
+#ifdef DEBUG_I82586_SHOW
+ wv_scb_show(ioaddr);
+#endif
+
+#ifdef DEBUG_CONFIG_TRACE
+ printk(KERN_DEBUG "%s: <-wv_82586_start()\n", dev->name);
+#endif
+ return 0;
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * This routine does a standard configuration of the WaveLAN
+ * controller (i82586).
+ *
+ * This routine is a violent hack. We use the first free transmit block
+ * to make our configuration. In the buffer area, we create the three
+ * configuration commands (linked). We make the previous NOP point to
+ * the beginning of the buffer instead of the tx command. After, we go
+ * as usual to the NOP command.
+ * Note that only the last command (mc_set) will generate an interrupt.
+ *
+ * (called by wv_hw_reset(), wv_82586_reconfig(), wavelan_packet_xmit())
+ */
+static void wv_82586_config(struct net_device * dev)
+{
+ net_local *lp = (net_local *) dev->priv;
+ unsigned long ioaddr = dev->base_addr;
+ unsigned short txblock;
+ unsigned short txpred;
+ unsigned short tx_addr;
+ unsigned short nop_addr;
+ unsigned short tbd_addr;
+ unsigned short cfg_addr;
+ unsigned short ias_addr;
+ unsigned short mcs_addr;
+ ac_tx_t tx;
+ ac_nop_t nop;
+ ac_cfg_t cfg; /* Configure action */
+ ac_ias_t ias; /* IA-setup action */
+ ac_mcs_t mcs; /* Multicast setup */
+ struct dev_mc_list *dmi;
+
+#ifdef DEBUG_CONFIG_TRACE
+ printk(KERN_DEBUG "%s: ->wv_82586_config()\n", dev->name);
+#endif
+
+ /* Check nothing bad has happened */
+ if (lp->tx_n_in_use == (NTXBLOCKS - 1)) {
+#ifdef DEBUG_CONFIG_ERROR
+ printk(KERN_INFO "%s: wv_82586_config(): Tx queue full.\n",
+ dev->name);
+#endif
+ return;
+ }
+
+ /* Calculate addresses of next block and previous block. */
+ txblock = lp->tx_first_free;
+ txpred = txblock - TXBLOCKZ;
+ if (txpred < OFFSET_CU)
+ txpred += NTXBLOCKS * TXBLOCKZ;
+ lp->tx_first_free += TXBLOCKZ;
+ if (lp->tx_first_free >= OFFSET_CU + NTXBLOCKS * TXBLOCKZ)
+ lp->tx_first_free -= NTXBLOCKS * TXBLOCKZ;
+
+ lp->tx_n_in_use++;
+
+ /* Calculate addresses of the different parts of the block. */
+ tx_addr = txblock;
+ nop_addr = tx_addr + sizeof(tx);
+ tbd_addr = nop_addr + sizeof(nop);
+ cfg_addr = tbd_addr + sizeof(tbd_t); /* beginning of the buffer */
+ ias_addr = cfg_addr + sizeof(cfg);
+ mcs_addr = ias_addr + sizeof(ias);
+
+ /*
+ * Transmit command
+ */
+ tx.tx_h.ac_status = 0xFFFF; /* Fake completion value */
+ obram_write(ioaddr, toff(ac_tx_t, tx_addr, tx_h.ac_status),
+ (unsigned char *) &tx.tx_h.ac_status,
+ sizeof(tx.tx_h.ac_status));
+
+ /*
+ * NOP command
+ */
+ nop.nop_h.ac_status = 0;
+ obram_write(ioaddr, toff(ac_nop_t, nop_addr, nop_h.ac_status),
+ (unsigned char *) &nop.nop_h.ac_status,
+ sizeof(nop.nop_h.ac_status));
+ nop.nop_h.ac_link = nop_addr;
+ obram_write(ioaddr, toff(ac_nop_t, nop_addr, nop_h.ac_link),
+ (unsigned char *) &nop.nop_h.ac_link,
+ sizeof(nop.nop_h.ac_link));
+
+ /* Create a configure action. */
+ memset(&cfg, 0x00, sizeof(cfg));
+
+ /*
+ * For Linux we invert AC_CFG_ALOC() so as to conform
+ * to the way that net packets reach us from above.
+ * (See also ac_tx_t.)
+ *
+ * Updated from Wavelan Manual WCIN085B
+ */
+ cfg.cfg_byte_cnt =
+ AC_CFG_BYTE_CNT(sizeof(ac_cfg_t) - sizeof(ach_t));
+ cfg.cfg_fifolim = AC_CFG_FIFOLIM(4);
+ cfg.cfg_byte8 = AC_CFG_SAV_BF(1) | AC_CFG_SRDY(0);
+ cfg.cfg_byte9 = AC_CFG_ELPBCK(0) |
+ AC_CFG_ILPBCK(0) |
+ AC_CFG_PRELEN(AC_CFG_PLEN_2) |
+ AC_CFG_ALOC(1) | AC_CFG_ADDRLEN(WAVELAN_ADDR_SIZE);
+ cfg.cfg_byte10 = AC_CFG_BOFMET(1) |
+ AC_CFG_ACR(6) | AC_CFG_LINPRIO(0);
+ cfg.cfg_ifs = 0x20;
+ cfg.cfg_slotl = 0x0C;
+ cfg.cfg_byte13 = AC_CFG_RETRYNUM(15) | AC_CFG_SLTTMHI(0);
+ cfg.cfg_byte14 = AC_CFG_FLGPAD(0) |
+ AC_CFG_BTSTF(0) |
+ AC_CFG_CRC16(0) |
+ AC_CFG_NCRC(0) |
+ AC_CFG_TNCRS(1) |
+ AC_CFG_MANCH(0) |
+ AC_CFG_BCDIS(0) | AC_CFG_PRM(lp->promiscuous);
+ cfg.cfg_byte15 = AC_CFG_ICDS(0) |
+ AC_CFG_CDTF(0) | AC_CFG_ICSS(0) | AC_CFG_CSTF(0);
+/*
+ cfg.cfg_min_frm_len = AC_CFG_MNFRM(64);
+*/
+ cfg.cfg_min_frm_len = AC_CFG_MNFRM(8);
+
+ cfg.cfg_h.ac_command = (AC_CFLD_CMD & acmd_configure);
+ cfg.cfg_h.ac_link = ias_addr;
+ obram_write(ioaddr, cfg_addr, (unsigned char *) &cfg, sizeof(cfg));
+
+ /* Set up the MAC address */
+ memset(&ias, 0x00, sizeof(ias));
+ ias.ias_h.ac_command = (AC_CFLD_CMD & acmd_ia_setup);
+ ias.ias_h.ac_link = mcs_addr;
+ memcpy(&ias.ias_addr[0], (unsigned char *) &dev->dev_addr[0],
+ sizeof(ias.ias_addr));
+ obram_write(ioaddr, ias_addr, (unsigned char *) &ias, sizeof(ias));
+
+ /* Initialize adapter's Ethernet multicast addresses */
+ memset(&mcs, 0x00, sizeof(mcs));
+ mcs.mcs_h.ac_command = AC_CFLD_I | (AC_CFLD_CMD & acmd_mc_setup);
+ mcs.mcs_h.ac_link = nop_addr;
+ mcs.mcs_cnt = WAVELAN_ADDR_SIZE * lp->mc_count;
+ obram_write(ioaddr, mcs_addr, (unsigned char *) &mcs, sizeof(mcs));
+
+ /* Any address to set? */
+ if (lp->mc_count) {
+ for (dmi = dev->mc_list; dmi; dmi = dmi->next)
+ outsw(PIOP1(ioaddr), (u16 *) dmi->dmi_addr,
+ WAVELAN_ADDR_SIZE >> 1);
+
+#ifdef DEBUG_CONFIG_INFO
+ printk(KERN_DEBUG
+ "%s: wv_82586_config(): set %d multicast addresses:\n",
+ dev->name, lp->mc_count);
+ for (dmi = dev->mc_list; dmi; dmi = dmi->next)
+ printk(KERN_DEBUG
+ " %02x:%02x:%02x:%02x:%02x:%02x\n",
+ dmi->dmi_addr[0], dmi->dmi_addr[1],
+ dmi->dmi_addr[2], dmi->dmi_addr[3],
+ dmi->dmi_addr[4], dmi->dmi_addr[5]);
+#endif
+ }
+
+ /*
+ * Overwrite the predecessor NOP link
+ * so that it points to the configure action.
+ */
+ nop_addr = txpred + sizeof(tx);
+ nop.nop_h.ac_status = 0;
+ obram_write(ioaddr, toff(ac_nop_t, nop_addr, nop_h.ac_status),
+ (unsigned char *) &nop.nop_h.ac_status,
+ sizeof(nop.nop_h.ac_status));
+ nop.nop_h.ac_link = cfg_addr;
+ obram_write(ioaddr, toff(ac_nop_t, nop_addr, nop_h.ac_link),
+ (unsigned char *) &nop.nop_h.ac_link,
+ sizeof(nop.nop_h.ac_link));
+
+ /* Job done, clear the flag */
+ lp->reconfig_82586 = 0;
+
+ if (lp->tx_first_in_use == I82586NULL)
+ lp->tx_first_in_use = txblock;
+
+ if (lp->tx_n_in_use == (NTXBLOCKS - 1))
+ netif_stop_queue(dev);
+
+#ifdef DEBUG_CONFIG_TRACE
+ printk(KERN_DEBUG "%s: <-wv_82586_config()\n", dev->name);
+#endif
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * This routine, called by wavelan_close(), gracefully stops the
+ * WaveLAN controller (i82586).
+ * (called by wavelan_close())
+ */
+static inline void wv_82586_stop(struct net_device * dev)
+{
+ net_local *lp = (net_local *) dev->priv;
+ unsigned long ioaddr = dev->base_addr;
+ u16 scb_cmd;
+
+#ifdef DEBUG_CONFIG_TRACE
+ printk(KERN_DEBUG "%s: ->wv_82586_stop()\n", dev->name);
+#endif
+
+ /* Suspend both command unit and receive unit. */
+ scb_cmd =
+ (SCB_CMD_CUC & SCB_CMD_CUC_SUS) | (SCB_CMD_RUC &
+ SCB_CMD_RUC_SUS);
+ obram_write(ioaddr, scboff(OFFSET_SCB, scb_command),
+ (unsigned char *) &scb_cmd, sizeof(scb_cmd));
+ set_chan_attn(ioaddr, lp->hacr);
+
+ /* No more interrupts */
+ wv_ints_off(dev);
+
+#ifdef DEBUG_CONFIG_TRACE
+ printk(KERN_DEBUG "%s: <-wv_82586_stop()\n", dev->name);
+#endif
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Totally reset the WaveLAN and restart it.
+ * Performs the following actions:
+ * 1. A power reset (reset DMA)
+ * 2. Initialize the radio modem (using wv_mmc_init)
+ * 3. Reset & Configure LAN controller (using wv_82586_start)
+ * 4. Start the LAN controller's command unit
+ * 5. Start the LAN controller's receive unit
+ * (called by wavelan_interrupt(), wavelan_watchdog() & wavelan_open())
+ */
+static int wv_hw_reset(struct net_device * dev)
+{
+ net_local *lp = (net_local *) dev->priv;
+ unsigned long ioaddr = dev->base_addr;
+
+#ifdef DEBUG_CONFIG_TRACE
+ printk(KERN_DEBUG "%s: ->wv_hw_reset(dev=0x%x)\n", dev->name,
+ (unsigned int) dev);
+#endif
+
+ /* Increase the number of resets done. */
+ lp->nresets++;
+
+ wv_hacr_reset(ioaddr);
+ lp->hacr = HACR_DEFAULT;
+
+ if ((wv_mmc_init(dev) < 0) || (wv_82586_start(dev) < 0))
+ return -1;
+
+ /* Enable the card to send interrupts. */
+ wv_ints_on(dev);
+
+ /* Start card functions */
+ if (wv_cu_start(dev) < 0)
+ return -1;
+
+ /* Setup the controller and parameters */
+ wv_82586_config(dev);
+
+ /* Finish configuration with the receive unit */
+ if (wv_ru_start(dev) < 0)
+ return -1;
+
+#ifdef DEBUG_CONFIG_TRACE
+ printk(KERN_DEBUG "%s: <-wv_hw_reset()\n", dev->name);
+#endif
+ return 0;
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Check if there is a WaveLAN at the specific base address.
+ * As a side effect, this reads the MAC address.
+ * (called in wavelan_probe() and init_module())
+ */
+static int wv_check_ioaddr(unsigned long ioaddr, u8 * mac)
+{
+ int i; /* Loop counter */
+
+ /* Check if the base address if available. */
+ if (!request_region(ioaddr, sizeof(ha_t), "wavelan probe"))
+ return -EBUSY; /* ioaddr already used */
+
+ /* Reset host interface */
+ wv_hacr_reset(ioaddr);
+
+ /* Read the MAC address from the parameter storage area. */
+ psa_read(ioaddr, HACR_DEFAULT, psaoff(0, psa_univ_mac_addr),
+ mac, 6);
+
+ release_region(ioaddr, sizeof(ha_t));
+
+ /*
+ * Check the first three octets of the address for the manufacturer's code.
+ * Note: if this can't find your WaveLAN card, you've got a
+ * non-NCR/AT&T/Lucent ISA card. See wavelan.p.h for detail on
+ * how to configure your card.
+ */
+ for (i = 0; i < (sizeof(MAC_ADDRESSES) / sizeof(char) / 3); i++)
+ if ((mac[0] == MAC_ADDRESSES[i][0]) &&
+ (mac[1] == MAC_ADDRESSES[i][1]) &&
+ (mac[2] == MAC_ADDRESSES[i][2]))
+ return 0;
+
+#ifdef DEBUG_CONFIG_INFO
+ printk(KERN_WARNING
+ "WaveLAN (0x%3X): your MAC address might be %02X:%02X:%02X.\n",
+ ioaddr, mac[0], mac[1], mac[2]);
+#endif
+ return -ENODEV;
+}
+
+/************************ INTERRUPT HANDLING ************************/
+
+/*
+ * This function is the interrupt handler for the WaveLAN card. This
+ * routine will be called whenever:
+ */
+static irqreturn_t wavelan_interrupt(int irq, void *dev_id, struct pt_regs *regs)
+{
+ struct net_device *dev;
+ unsigned long ioaddr;
+ net_local *lp;
+ u16 hasr;
+ u16 status;
+ u16 ack_cmd;
+
+ dev = dev_id;
+
+#ifdef DEBUG_INTERRUPT_TRACE
+ printk(KERN_DEBUG "%s: ->wavelan_interrupt()\n", dev->name);
+#endif
+
+ lp = (net_local *) dev->priv;
+ ioaddr = dev->base_addr;
+
+#ifdef DEBUG_INTERRUPT_INFO
+ /* Check state of our spinlock */
+ if(spin_is_locked(&lp->spinlock))
+ printk(KERN_DEBUG
+ "%s: wavelan_interrupt(): spinlock is already locked !!!\n",
+ dev->name);
+#endif
+
+ /* Prevent reentrancy. We need to do that because we may have
+ * multiple interrupt handler running concurrently.
+ * It is safe because interrupts are disabled before acquiring
+ * the spinlock. */
+ spin_lock(&lp->spinlock);
+
+ /* We always had spurious interrupts at startup, but lately I
+ * saw them comming *between* the request_irq() and the
+ * spin_lock_irqsave() in wavelan_open(), so the spinlock
+ * protection is no enough.
+ * So, we also check lp->hacr that will tell us is we enabled
+ * irqs or not (see wv_ints_on()).
+ * We can't use netif_running(dev) because we depend on the
+ * proper processing of the irq generated during the config. */
+
+ /* Which interrupt it is ? */
+ hasr = hasr_read(ioaddr);
+
+#ifdef DEBUG_INTERRUPT_INFO
+ printk(KERN_INFO
+ "%s: wavelan_interrupt(): hasr 0x%04x; hacr 0x%04x.\n",
+ dev->name, hasr, lp->hacr);
+#endif
+
+ /* Check modem interrupt */
+ if ((hasr & HASR_MMC_INTR) && (lp->hacr & HACR_MMC_INT_ENABLE)) {
+ u8 dce_status;
+
+ /*
+ * Interrupt from the modem management controller.
+ * This will clear it -- ignored for now.
+ */
+ mmc_read(ioaddr, mmroff(0, mmr_dce_status), &dce_status,
+ sizeof(dce_status));
+
+#ifdef DEBUG_INTERRUPT_ERROR
+ printk(KERN_INFO
+ "%s: wavelan_interrupt(): unexpected mmc interrupt: status 0x%04x.\n",
+ dev->name, dce_status);
+#endif
+ }
+
+ /* Check if not controller interrupt */
+ if (((hasr & HASR_82586_INTR) == 0) ||
+ ((lp->hacr & HACR_82586_INT_ENABLE) == 0)) {
+#ifdef DEBUG_INTERRUPT_ERROR
+ printk(KERN_INFO
+ "%s: wavelan_interrupt(): interrupt not coming from i82586 - hasr 0x%04x.\n",
+ dev->name, hasr);
+#endif
+ spin_unlock (&lp->spinlock);
+ return IRQ_NONE;
+ }
+
+ /* Read interrupt data. */
+ obram_read(ioaddr, scboff(OFFSET_SCB, scb_status),
+ (unsigned char *) &status, sizeof(status));
+
+ /*
+ * Acknowledge the interrupt(s).
+ */
+ ack_cmd = status & SCB_ST_INT;
+ obram_write(ioaddr, scboff(OFFSET_SCB, scb_command),
+ (unsigned char *) &ack_cmd, sizeof(ack_cmd));
+ set_chan_attn(ioaddr, lp->hacr);
+
+#ifdef DEBUG_INTERRUPT_INFO
+ printk(KERN_DEBUG "%s: wavelan_interrupt(): status 0x%04x.\n",
+ dev->name, status);
+#endif
+
+ /* Command completed. */
+ if ((status & SCB_ST_CX) == SCB_ST_CX) {
+#ifdef DEBUG_INTERRUPT_INFO
+ printk(KERN_DEBUG
+ "%s: wavelan_interrupt(): command completed.\n",
+ dev->name);
+#endif
+ wv_complete(dev, ioaddr, lp);
+ }
+
+ /* Frame received. */
+ if ((status & SCB_ST_FR) == SCB_ST_FR) {
+#ifdef DEBUG_INTERRUPT_INFO
+ printk(KERN_DEBUG
+ "%s: wavelan_interrupt(): received packet.\n",
+ dev->name);
+#endif
+ wv_receive(dev);
+ }
+
+ /* Check the state of the command unit. */
+ if (((status & SCB_ST_CNA) == SCB_ST_CNA) ||
+ (((status & SCB_ST_CUS) != SCB_ST_CUS_ACTV) &&
+ (netif_running(dev)))) {
+#ifdef DEBUG_INTERRUPT_ERROR
+ printk(KERN_INFO
+ "%s: wavelan_interrupt(): CU inactive -- restarting\n",
+ dev->name);
+#endif
+ wv_hw_reset(dev);
+ }
+
+ /* Check the state of the command unit. */
+ if (((status & SCB_ST_RNR) == SCB_ST_RNR) ||
+ (((status & SCB_ST_RUS) != SCB_ST_RUS_RDY) &&
+ (netif_running(dev)))) {
+#ifdef DEBUG_INTERRUPT_ERROR
+ printk(KERN_INFO
+ "%s: wavelan_interrupt(): RU not ready -- restarting\n",
+ dev->name);
+#endif
+ wv_hw_reset(dev);
+ }
+
+ /* Release spinlock */
+ spin_unlock (&lp->spinlock);
+
+#ifdef DEBUG_INTERRUPT_TRACE
+ printk(KERN_DEBUG "%s: <-wavelan_interrupt()\n", dev->name);
+#endif
+ return IRQ_HANDLED;
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Watchdog: when we start a transmission, a timer is set for us in the
+ * kernel. If the transmission completes, this timer is disabled. If
+ * the timer expires, we are called and we try to unlock the hardware.
+ */
+static void wavelan_watchdog(struct net_device * dev)
+{
+ net_local * lp = (net_local *)dev->priv;
+ u_long ioaddr = dev->base_addr;
+ unsigned long flags;
+ unsigned int nreaped;
+
+#ifdef DEBUG_INTERRUPT_TRACE
+ printk(KERN_DEBUG "%s: ->wavelan_watchdog()\n", dev->name);
+#endif
+
+#ifdef DEBUG_INTERRUPT_ERROR
+ printk(KERN_INFO "%s: wavelan_watchdog: watchdog timer expired\n",
+ dev->name);
+#endif
+
+ /* Check that we came here for something */
+ if (lp->tx_n_in_use <= 0) {
+ return;
+ }
+
+ spin_lock_irqsave(&lp->spinlock, flags);
+
+ /* Try to see if some buffers are not free (in case we missed
+ * an interrupt */
+ nreaped = wv_complete(dev, ioaddr, lp);
+
+#ifdef DEBUG_INTERRUPT_INFO
+ printk(KERN_DEBUG
+ "%s: wavelan_watchdog(): %d reaped, %d remain.\n",
+ dev->name, nreaped, lp->tx_n_in_use);
+#endif
+
+#ifdef DEBUG_PSA_SHOW
+ {
+ psa_t psa;
+ psa_read(dev, 0, (unsigned char *) &psa, sizeof(psa));
+ wv_psa_show(&psa);
+ }
+#endif
+#ifdef DEBUG_MMC_SHOW
+ wv_mmc_show(dev);
+#endif
+#ifdef DEBUG_I82586_SHOW
+ wv_cu_show(dev);
+#endif
+
+ /* If no buffer has been freed */
+ if (nreaped == 0) {
+#ifdef DEBUG_INTERRUPT_ERROR
+ printk(KERN_INFO
+ "%s: wavelan_watchdog(): cleanup failed, trying reset\n",
+ dev->name);
+#endif
+ wv_hw_reset(dev);
+ }
+
+ /* At this point, we should have some free Tx buffer ;-) */
+ if (lp->tx_n_in_use < NTXBLOCKS - 1)
+ netif_wake_queue(dev);
+
+ spin_unlock_irqrestore(&lp->spinlock, flags);
+
+#ifdef DEBUG_INTERRUPT_TRACE
+ printk(KERN_DEBUG "%s: <-wavelan_watchdog()\n", dev->name);
+#endif
+}
+
+/********************* CONFIGURATION CALLBACKS *********************/
+/*
+ * Here are the functions called by the Linux networking code (NET3)
+ * for initialization, configuration and deinstallations of the
+ * WaveLAN ISA hardware.
+ */
+
+/*------------------------------------------------------------------*/
+/*
+ * Configure and start up the WaveLAN PCMCIA adaptor.
+ * Called by NET3 when it "opens" the device.
+ */
+static int wavelan_open(struct net_device * dev)
+{
+ net_local * lp = (net_local *)dev->priv;
+ unsigned long flags;
+
+#ifdef DEBUG_CALLBACK_TRACE
+ printk(KERN_DEBUG "%s: ->wavelan_open(dev=0x%x)\n", dev->name,
+ (unsigned int) dev);
+#endif
+
+ /* Check irq */
+ if (dev->irq == 0) {
+#ifdef DEBUG_CONFIG_ERROR
+ printk(KERN_WARNING "%s: wavelan_open(): no IRQ\n",
+ dev->name);
+#endif
+ return -ENXIO;
+ }
+
+ if (request_irq(dev->irq, &wavelan_interrupt, 0, "WaveLAN", dev) != 0)
+ {
+#ifdef DEBUG_CONFIG_ERROR
+ printk(KERN_WARNING "%s: wavelan_open(): invalid IRQ\n",
+ dev->name);
+#endif
+ return -EAGAIN;
+ }
+
+ spin_lock_irqsave(&lp->spinlock, flags);
+
+ if (wv_hw_reset(dev) != -1) {
+ netif_start_queue(dev);
+ } else {
+ free_irq(dev->irq, dev);
+#ifdef DEBUG_CONFIG_ERROR
+ printk(KERN_INFO
+ "%s: wavelan_open(): impossible to start the card\n",
+ dev->name);
+#endif
+ spin_unlock_irqrestore(&lp->spinlock, flags);
+ return -EAGAIN;
+ }
+ spin_unlock_irqrestore(&lp->spinlock, flags);
+
+#ifdef DEBUG_CALLBACK_TRACE
+ printk(KERN_DEBUG "%s: <-wavelan_open()\n", dev->name);
+#endif
+ return 0;
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Shut down the WaveLAN ISA card.
+ * Called by NET3 when it "closes" the device.
+ */
+static int wavelan_close(struct net_device * dev)
+{
+ net_local *lp = (net_local *) dev->priv;
+ unsigned long flags;
+
+#ifdef DEBUG_CALLBACK_TRACE
+ printk(KERN_DEBUG "%s: ->wavelan_close(dev=0x%x)\n", dev->name,
+ (unsigned int) dev);
+#endif
+
+ netif_stop_queue(dev);
+
+ /*
+ * Flush the Tx and disable Rx.
+ */
+ spin_lock_irqsave(&lp->spinlock, flags);
+ wv_82586_stop(dev);
+ spin_unlock_irqrestore(&lp->spinlock, flags);
+
+ free_irq(dev->irq, dev);
+
+#ifdef DEBUG_CALLBACK_TRACE
+ printk(KERN_DEBUG "%s: <-wavelan_close()\n", dev->name);
+#endif
+ return 0;
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Probe an I/O address, and if the WaveLAN is there configure the
+ * device structure
+ * (called by wavelan_probe() and via init_module()).
+ */
+static int __init wavelan_config(struct net_device *dev, unsigned short ioaddr)
+{
+ u8 irq_mask;
+ int irq;
+ net_local *lp;
+ mac_addr mac;
+ int err;
+
+ if (!request_region(ioaddr, sizeof(ha_t), "wavelan"))
+ return -EADDRINUSE;
+
+ err = wv_check_ioaddr(ioaddr, mac);
+ if (err)
+ goto out;
+
+ memcpy(dev->dev_addr, mac, 6);
+
+ dev->base_addr = ioaddr;
+
+#ifdef DEBUG_CALLBACK_TRACE
+ printk(KERN_DEBUG "%s: ->wavelan_config(dev=0x%x, ioaddr=0x%lx)\n",
+ dev->name, (unsigned int) dev, ioaddr);
+#endif
+
+ /* Check IRQ argument on command line. */
+ if (dev->irq != 0) {
+ irq_mask = wv_irq_to_psa(dev->irq);
+
+ if (irq_mask == 0) {
+#ifdef DEBUG_CONFIG_ERROR
+ printk(KERN_WARNING
+ "%s: wavelan_config(): invalid IRQ %d ignored.\n",
+ dev->name, dev->irq);
+#endif
+ dev->irq = 0;
+ } else {
+#ifdef DEBUG_CONFIG_INFO
+ printk(KERN_DEBUG
+ "%s: wavelan_config(): changing IRQ to %d\n",
+ dev->name, dev->irq);
+#endif
+ psa_write(ioaddr, HACR_DEFAULT,
+ psaoff(0, psa_int_req_no), &irq_mask, 1);
+ /* update the Wavelan checksum */
+ update_psa_checksum(dev, ioaddr, HACR_DEFAULT);
+ wv_hacr_reset(ioaddr);
+ }
+ }
+
+ psa_read(ioaddr, HACR_DEFAULT, psaoff(0, psa_int_req_no),
+ &irq_mask, 1);
+ if ((irq = wv_psa_to_irq(irq_mask)) == -1) {
+#ifdef DEBUG_CONFIG_ERROR
+ printk(KERN_INFO
+ "%s: wavelan_config(): could not wavelan_map_irq(%d).\n",
+ dev->name, irq_mask);
+#endif
+ err = -EAGAIN;
+ goto out;
+ }
+
+ dev->irq = irq;
+
+ dev->mem_start = 0x0000;
+ dev->mem_end = 0x0000;
+ dev->if_port = 0;
+
+ /* Initialize device structures */
+ memset(dev->priv, 0, sizeof(net_local));
+ lp = (net_local *) dev->priv;
+
+ /* Back link to the device structure. */
+ lp->dev = dev;
+ /* Add the device at the beginning of the linked list. */
+ lp->next = wavelan_list;
+ wavelan_list = lp;
+
+ lp->hacr = HACR_DEFAULT;
+
+ /* Multicast stuff */
+ lp->promiscuous = 0;
+ lp->mc_count = 0;
+
+ /* Init spinlock */
+ spin_lock_init(&lp->spinlock);
+
+ SET_MODULE_OWNER(dev);
+ dev->open = wavelan_open;
+ dev->stop = wavelan_close;
+ dev->hard_start_xmit = wavelan_packet_xmit;
+ dev->get_stats = wavelan_get_stats;
+ dev->set_multicast_list = &wavelan_set_multicast_list;
+ dev->tx_timeout = &wavelan_watchdog;
+ dev->watchdog_timeo = WATCHDOG_JIFFIES;
+#ifdef SET_MAC_ADDRESS
+ dev->set_mac_address = &wavelan_set_mac_address;
+#endif /* SET_MAC_ADDRESS */
+
+#ifdef WIRELESS_EXT /* if wireless extension exists in the kernel */
+ dev->wireless_handlers = &wavelan_handler_def;
+ lp->wireless_data.spy_data = &lp->spy_data;
+ dev->wireless_data = &lp->wireless_data;
+#endif
+
+ dev->mtu = WAVELAN_MTU;
+
+ /* Display nice information. */
+ wv_init_info(dev);
+
+#ifdef DEBUG_CALLBACK_TRACE
+ printk(KERN_DEBUG "%s: <-wavelan_config()\n", dev->name);
+#endif
+ return 0;
+out:
+ release_region(ioaddr, sizeof(ha_t));
+ return err;
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Check for a network adaptor of this type. Return '0' iff one
+ * exists. There seem to be different interpretations of
+ * the initial value of dev->base_addr.
+ * We follow the example in drivers/net/ne.c.
+ * (called in "Space.c")
+ */
+struct net_device * __init wavelan_probe(int unit)
+{
+ struct net_device *dev;
+ short base_addr;
+ int def_irq;
+ int i;
+ int r = 0;
+
+#ifdef STRUCT_CHECK
+ if (wv_struct_check() != (char *) NULL) {
+ printk(KERN_WARNING
+ "%s: wavelan_probe(): structure/compiler botch: \"%s\"\n",
+ dev->name, wv_struct_check());
+ return -ENODEV;
+ }
+#endif /* STRUCT_CHECK */
+
+ dev = alloc_etherdev(sizeof(net_local));
+ if (!dev)
+ return ERR_PTR(-ENOMEM);
+
+ sprintf(dev->name, "eth%d", unit);
+ netdev_boot_setup_check(dev);
+ base_addr = dev->base_addr;
+ def_irq = dev->irq;
+
+#ifdef DEBUG_CALLBACK_TRACE
+ printk(KERN_DEBUG
+ "%s: ->wavelan_probe(dev=%p (base_addr=0x%x))\n",
+ dev->name, dev, (unsigned int) dev->base_addr);
+#endif
+
+ /* Don't probe at all. */
+ if (base_addr < 0) {
+#ifdef DEBUG_CONFIG_ERROR
+ printk(KERN_WARNING
+ "%s: wavelan_probe(): invalid base address\n",
+ dev->name);
+#endif
+ r = -ENXIO;
+ } else if (base_addr > 0x100) { /* Check a single specified location. */
+ r = wavelan_config(dev, base_addr);
+#ifdef DEBUG_CONFIG_INFO
+ if (r != 0)
+ printk(KERN_DEBUG
+ "%s: wavelan_probe(): no device at specified base address (0x%X) or address already in use\n",
+ dev->name, base_addr);
+#endif
+
+#ifdef DEBUG_CALLBACK_TRACE
+ printk(KERN_DEBUG "%s: <-wavelan_probe()\n", dev->name);
+#endif
+ } else { /* Scan all possible addresses of the WaveLAN hardware. */
+ for (i = 0; i < NELS(iobase); i++) {
+ dev->irq = def_irq;
+ if (wavelan_config(dev, iobase[i]) == 0) {
+#ifdef DEBUG_CALLBACK_TRACE
+ printk(KERN_DEBUG
+ "%s: <-wavelan_probe()\n",
+ dev->name);
+#endif
+ break;
+ }
+ }
+ if (i == NELS(iobase))
+ r = -ENODEV;
+ }
+ if (r)
+ goto out;
+ r = register_netdev(dev);
+ if (r)
+ goto out1;
+ return dev;
+out1:
+ release_region(dev->base_addr, sizeof(ha_t));
+ wavelan_list = wavelan_list->next;
+out:
+ free_netdev(dev);
+ return ERR_PTR(r);
+}
+
+/****************************** MODULE ******************************/
+/*
+ * Module entry point: insertion and removal
+ */
+
+#ifdef MODULE
+/*------------------------------------------------------------------*/
+/*
+ * Insertion of the module
+ * I'm now quite proud of the multi-device support.
+ */
+int init_module(void)
+{
+ int ret = -EIO; /* Return error if no cards found */
+ int i;
+
+#ifdef DEBUG_MODULE_TRACE
+ printk(KERN_DEBUG "-> init_module()\n");
+#endif
+
+ /* If probing is asked */
+ if (io[0] == 0) {
+#ifdef DEBUG_CONFIG_ERROR
+ printk(KERN_WARNING
+ "WaveLAN init_module(): doing device probing (bad !)\n");
+ printk(KERN_WARNING
+ "Specify base addresses while loading module to correct the problem\n");
+#endif
+
+ /* Copy the basic set of address to be probed. */
+ for (i = 0; i < NELS(iobase); i++)
+ io[i] = iobase[i];
+ }
+
+
+ /* Loop on all possible base addresses. */
+ i = -1;
+ while ((io[++i] != 0) && (i < NELS(io))) {
+ struct net_device *dev = alloc_etherdev(sizeof(net_local));
+ if (!dev)
+ break;
+ if (name[i])
+ strcpy(dev->name, name[i]); /* Copy name */
+ dev->base_addr = io[i];
+ dev->irq = irq[i];
+
+ /* Check if there is something at this base address. */
+ if (wavelan_config(dev, io[i]) == 0) {
+ if (register_netdev(dev) != 0) {
+ release_region(dev->base_addr, sizeof(ha_t));
+ wavelan_list = wavelan_list->next;
+ } else {
+ ret = 0;
+ continue;
+ }
+ }
+ free_netdev(dev);
+ }
+
+#ifdef DEBUG_CONFIG_ERROR
+ if (!wavelan_list)
+ printk(KERN_WARNING
+ "WaveLAN init_module(): no device found\n");
+#endif
+
+#ifdef DEBUG_MODULE_TRACE
+ printk(KERN_DEBUG "<- init_module()\n");
+#endif
+ return ret;
+}
+
+/*------------------------------------------------------------------*/
+/*
+ * Removal of the module
+ */
+void cleanup_module(void)
+{
+#ifdef DEBUG_MODULE_TRACE
+ printk(KERN_DEBUG "-> cleanup_module()\n");
+#endif
+
+ /* Loop on all devices and release them. */
+ while (wavelan_list) {
+ struct net_device *dev = wavelan_list->dev;
+
+#ifdef DEBUG_CONFIG_INFO
+ printk(KERN_DEBUG
+ "%s: cleanup_module(): removing device at 0x%x\n",
+ dev->name, (unsigned int) dev);
+#endif
+ unregister_netdev(dev);
+
+ release_region(dev->base_addr, sizeof(ha_t));
+ wavelan_list = wavelan_list->next;
+
+ free_netdev(dev);
+ }
+
+#ifdef DEBUG_MODULE_TRACE
+ printk(KERN_DEBUG "<- cleanup_module()\n");
+#endif
+}
+#endif /* MODULE */
+MODULE_LICENSE("GPL");
+
+/*
+ * This software may only be used and distributed
+ * according to the terms of the GNU General Public License.
+ *
+ * This software was developed as a component of the
+ * Linux operating system.
+ * It is based on other device drivers and information
+ * either written or supplied by:
+ * Ajay Bakre (bakre@paul.rutgers.edu),
+ * Donald Becker (becker@scyld.com),
+ * Loeke Brederveld (Loeke.Brederveld@Utrecht.NCR.com),
+ * Anders Klemets (klemets@it.kth.se),
+ * Vladimir V. Kolpakov (w@stier.koenig.ru),
+ * Marc Meertens (Marc.Meertens@Utrecht.NCR.com),
+ * Pauline Middelink (middelin@polyware.iaf.nl),
+ * Robert Morris (rtm@das.harvard.edu),
+ * Jean Tourrilhes (jt@hplb.hpl.hp.com),
+ * Girish Welling (welling@paul.rutgers.edu),
+ *
+ * Thanks go also to:
+ * James Ashton (jaa101@syseng.anu.edu.au),
+ * Alan Cox (alan@redhat.com),
+ * Allan Creighton (allanc@cs.usyd.edu.au),
+ * Matthew Geier (matthew@cs.usyd.edu.au),
+ * Remo di Giovanni (remo@cs.usyd.edu.au),
+ * Eckhard Grah (grah@wrcs1.urz.uni-wuppertal.de),
+ * Vipul Gupta (vgupta@cs.binghamton.edu),
+ * Mark Hagan (mhagan@wtcpost.daytonoh.NCR.COM),
+ * Tim Nicholson (tim@cs.usyd.edu.au),
+ * Ian Parkin (ian@cs.usyd.edu.au),
+ * John Rosenberg (johnr@cs.usyd.edu.au),
+ * George Rossi (george@phm.gov.au),
+ * Arthur Scott (arthur@cs.usyd.edu.au),
+ * Peter Storey,
+ * for their assistance and advice.
+ *
+ * Please send bug reports, updates, comments to:
+ *
+ * Bruce Janson Email: bruce@cs.usyd.edu.au
+ * Basser Department of Computer Science Phone: +61-2-9351-3423
+ * University of Sydney, N.S.W., 2006, AUSTRALIA Fax: +61-2-9351-3838
+ */