Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/drivers/scsi/dc395x.h b/drivers/scsi/dc395x.h
new file mode 100644
index 0000000..b38360e
--- /dev/null
+++ b/drivers/scsi/dc395x.h
@@ -0,0 +1,648 @@
+/************************************************************************/
+/* */
+/* dc395x.h */
+/* */
+/* Device Driver for Tekram DC395(U/UW/F), DC315(U) */
+/* PCI SCSI Bus Master Host Adapter */
+/* (SCSI chip set used Tekram ASIC TRM-S1040) */
+/* */
+/************************************************************************/
+#ifndef DC395x_H
+#define DC395x_H
+
+/************************************************************************/
+/* */
+/* Initial values */
+/* */
+/************************************************************************/
+#define DC395x_MAX_CMD_QUEUE 32
+/* #define DC395x_MAX_QTAGS 32 */
+#define DC395x_MAX_QTAGS 16
+#define DC395x_MAX_SCSI_ID 16
+#define DC395x_MAX_CMD_PER_LUN DC395x_MAX_QTAGS
+#define DC395x_MAX_SG_TABLESIZE 64 /* HW limitation */
+#define DC395x_MAX_SG_LISTENTRY 64 /* Must be equal or lower to previous */
+ /* item */
+#define DC395x_MAX_SRB_CNT 63
+/* #define DC395x_MAX_CAN_QUEUE 7 * DC395x_MAX_QTAGS */
+#define DC395x_MAX_CAN_QUEUE DC395x_MAX_SRB_CNT
+#define DC395x_END_SCAN 2
+#define DC395x_SEL_TIMEOUT 153 /* 250 ms selection timeout (@ 40 MHz) */
+#define DC395x_MAX_RETRIES 3
+
+#if 0
+#define SYNC_FIRST
+#endif
+
+#define NORM_REC_LVL 0
+
+/************************************************************************/
+/* */
+/* Various definitions */
+/* */
+/************************************************************************/
+#define BIT31 0x80000000
+#define BIT30 0x40000000
+#define BIT29 0x20000000
+#define BIT28 0x10000000
+#define BIT27 0x08000000
+#define BIT26 0x04000000
+#define BIT25 0x02000000
+#define BIT24 0x01000000
+#define BIT23 0x00800000
+#define BIT22 0x00400000
+#define BIT21 0x00200000
+#define BIT20 0x00100000
+#define BIT19 0x00080000
+#define BIT18 0x00040000
+#define BIT17 0x00020000
+#define BIT16 0x00010000
+#define BIT15 0x00008000
+#define BIT14 0x00004000
+#define BIT13 0x00002000
+#define BIT12 0x00001000
+#define BIT11 0x00000800
+#define BIT10 0x00000400
+#define BIT9 0x00000200
+#define BIT8 0x00000100
+#define BIT7 0x00000080
+#define BIT6 0x00000040
+#define BIT5 0x00000020
+#define BIT4 0x00000010
+#define BIT3 0x00000008
+#define BIT2 0x00000004
+#define BIT1 0x00000002
+#define BIT0 0x00000001
+
+/* UnitCtrlFlag */
+#define UNIT_ALLOCATED BIT0
+#define UNIT_INFO_CHANGED BIT1
+#define FORMATING_MEDIA BIT2
+#define UNIT_RETRY BIT3
+
+/* UnitFlags */
+#define DASD_SUPPORT BIT0
+#define SCSI_SUPPORT BIT1
+#define ASPI_SUPPORT BIT2
+
+/* SRBState machine definition */
+#define SRB_FREE 0x0000
+#define SRB_WAIT 0x0001
+#define SRB_READY 0x0002
+#define SRB_MSGOUT 0x0004 /* arbitration+msg_out 1st byte */
+#define SRB_MSGIN 0x0008
+#define SRB_EXTEND_MSGIN 0x0010
+#define SRB_COMMAND 0x0020
+#define SRB_START_ 0x0040 /* arbitration+msg_out+command_out */
+#define SRB_DISCONNECT 0x0080
+#define SRB_DATA_XFER 0x0100
+#define SRB_XFERPAD 0x0200
+#define SRB_STATUS 0x0400
+#define SRB_COMPLETED 0x0800
+#define SRB_ABORT_SENT 0x1000
+#define SRB_DO_SYNC_NEGO 0x2000
+#define SRB_DO_WIDE_NEGO 0x4000
+#define SRB_UNEXPECT_RESEL 0x8000
+
+/************************************************************************/
+/* */
+/* ACB Config */
+/* */
+/************************************************************************/
+#define HCC_WIDE_CARD 0x20
+#define HCC_SCSI_RESET 0x10
+#define HCC_PARITY 0x08
+#define HCC_AUTOTERM 0x04
+#define HCC_LOW8TERM 0x02
+#define HCC_UP8TERM 0x01
+
+/* ACBFlag */
+#define RESET_DEV BIT0
+#define RESET_DETECT BIT1
+#define RESET_DONE BIT2
+
+/* DCBFlag */
+#define ABORT_DEV_ BIT0
+
+/* SRBstatus */
+#define SRB_OK BIT0
+#define ABORTION BIT1
+#define OVER_RUN BIT2
+#define UNDER_RUN BIT3
+#define PARITY_ERROR BIT4
+#define SRB_ERROR BIT5
+
+/* SRBFlag */
+#define DATAOUT BIT7
+#define DATAIN BIT6
+#define RESIDUAL_VALID BIT5
+#define ENABLE_TIMER BIT4
+#define RESET_DEV0 BIT2
+#define ABORT_DEV BIT1
+#define AUTO_REQSENSE BIT0
+
+/* Adapter status */
+#define H_STATUS_GOOD 0
+#define H_SEL_TIMEOUT 0x11
+#define H_OVER_UNDER_RUN 0x12
+#define H_UNEXP_BUS_FREE 0x13
+#define H_TARGET_PHASE_F 0x14
+#define H_INVALID_CCB_OP 0x16
+#define H_LINK_CCB_BAD 0x17
+#define H_BAD_TARGET_DIR 0x18
+#define H_DUPLICATE_CCB 0x19
+#define H_BAD_CCB_OR_SG 0x1A
+#define H_ABORT 0x0FF
+
+/* SCSI BUS Status byte codes */
+#define SCSI_STAT_GOOD 0x0 /* Good status */
+#define SCSI_STAT_CHECKCOND 0x02 /* SCSI Check Condition */
+#define SCSI_STAT_CONDMET 0x04 /* Condition Met */
+#define SCSI_STAT_BUSY 0x08 /* Target busy status */
+#define SCSI_STAT_INTER 0x10 /* Intermediate status */
+#define SCSI_STAT_INTERCONDMET 0x14 /* Intermediate condition met */
+#define SCSI_STAT_RESCONFLICT 0x18 /* Reservation conflict */
+#define SCSI_STAT_CMDTERM 0x22 /* Command Terminated */
+#define SCSI_STAT_QUEUEFULL 0x28 /* Queue Full */
+#define SCSI_STAT_UNEXP_BUS_F 0xFD /* Unexpect Bus Free */
+#define SCSI_STAT_BUS_RST_DETECT 0xFE /* Scsi Bus Reset detected */
+#define SCSI_STAT_SEL_TIMEOUT 0xFF /* Selection Time out */
+
+/* Sync_Mode */
+#define SYNC_WIDE_TAG_ATNT_DISABLE 0
+#define SYNC_NEGO_ENABLE BIT0
+#define SYNC_NEGO_DONE BIT1
+#define WIDE_NEGO_ENABLE BIT2
+#define WIDE_NEGO_DONE BIT3
+#define WIDE_NEGO_STATE BIT4
+#define EN_TAG_QUEUEING BIT5
+#define EN_ATN_STOP BIT6
+
+#define SYNC_NEGO_OFFSET 15
+
+/* SCSI MSG BYTE */
+#define MSG_COMPLETE 0x00
+#define MSG_EXTENDED 0x01
+#define MSG_SAVE_PTR 0x02
+#define MSG_RESTORE_PTR 0x03
+#define MSG_DISCONNECT 0x04
+#define MSG_INITIATOR_ERROR 0x05
+#define MSG_ABORT 0x06
+#define MSG_REJECT_ 0x07
+#define MSG_NOP 0x08
+#define MSG_PARITY_ERROR 0x09
+#define MSG_LINK_CMD_COMPL 0x0A
+#define MSG_LINK_CMD_COMPL_FLG 0x0B
+#define MSG_BUS_RESET 0x0C
+#define MSG_ABORT_TAG 0x0D
+#define MSG_SIMPLE_QTAG 0x20
+#define MSG_HEAD_QTAG 0x21
+#define MSG_ORDER_QTAG 0x22
+#define MSG_IGNOREWIDE 0x23
+#define MSG_IDENTIFY 0x80
+#define MSG_HOST_ID 0xC0
+
+/* SCSI STATUS BYTE */
+#define STATUS_GOOD 0x00
+#define CHECK_CONDITION_ 0x02
+#define STATUS_BUSY 0x08
+#define STATUS_INTERMEDIATE 0x10
+#define RESERVE_CONFLICT 0x18
+
+/* cmd->result */
+#define STATUS_MASK_ 0xFF
+#define MSG_MASK 0xFF00
+#define RETURN_MASK 0xFF0000
+
+/************************************************************************/
+/* */
+/* Inquiry Data format */
+/* */
+/************************************************************************/
+struct ScsiInqData
+{ /* INQ */
+ u8 DevType; /* Periph Qualifier & Periph Dev Type */
+ u8 RMB_TypeMod; /* rem media bit & Dev Type Modifier */
+ u8 Vers; /* ISO, ECMA, & ANSI versions */
+ u8 RDF; /* AEN, TRMIOP, & response data format */
+ u8 AddLen; /* length of additional data */
+ u8 Res1; /* reserved */
+ u8 Res2; /* reserved */
+ u8 Flags; /* RelADr, Wbus32, Wbus16, Sync, etc. */
+ u8 VendorID[8]; /* Vendor Identification */
+ u8 ProductID[16]; /* Product Identification */
+ u8 ProductRev[4]; /* Product Revision */
+};
+
+ /* Inquiry byte 0 masks */
+#define SCSI_DEVTYPE 0x1F /* Peripheral Device Type */
+#define SCSI_PERIPHQUAL 0xE0 /* Peripheral Qualifier */
+ /* Inquiry byte 1 mask */
+#define SCSI_REMOVABLE_MEDIA 0x80 /* Removable Media bit (1=removable) */
+ /* Peripheral Device Type definitions */
+ /* See include/scsi/scsi.h */
+#define TYPE_NODEV SCSI_DEVTYPE /* Unknown or no device type */
+#ifndef TYPE_PRINTER /* */
+# define TYPE_PRINTER 0x02 /* Printer device */
+#endif /* */
+#ifndef TYPE_COMM /* */
+# define TYPE_COMM 0x09 /* Communications device */
+#endif
+
+/************************************************************************/
+/* */
+/* Inquiry flag definitions (Inq data byte 7) */
+/* */
+/************************************************************************/
+#define SCSI_INQ_RELADR 0x80 /* device supports relative addressing */
+#define SCSI_INQ_WBUS32 0x40 /* device supports 32 bit data xfers */
+#define SCSI_INQ_WBUS16 0x20 /* device supports 16 bit data xfers */
+#define SCSI_INQ_SYNC 0x10 /* device supports synchronous xfer */
+#define SCSI_INQ_LINKED 0x08 /* device supports linked commands */
+#define SCSI_INQ_CMDQUEUE 0x02 /* device supports command queueing */
+#define SCSI_INQ_SFTRE 0x01 /* device supports soft resets */
+
+#define ENABLE_CE 1
+#define DISABLE_CE 0
+#define EEPROM_READ 0x80
+
+/************************************************************************/
+/* */
+/* The PCI configuration register offset for TRM_S1040 */
+/* */
+/************************************************************************/
+#define TRM_S1040_ID 0x00 /* Vendor and Device ID */
+#define TRM_S1040_COMMAND 0x04 /* PCI command register */
+#define TRM_S1040_IOBASE 0x10 /* I/O Space base address */
+#define TRM_S1040_ROMBASE 0x30 /* Expansion ROM Base Address */
+#define TRM_S1040_INTLINE 0x3C /* Interrupt line */
+
+/************************************************************************/
+/* */
+/* The SCSI register offset for TRM_S1040 */
+/* */
+/************************************************************************/
+#define TRM_S1040_SCSI_STATUS 0x80 /* SCSI Status (R) */
+#define COMMANDPHASEDONE 0x2000 /* SCSI command phase done */
+#define SCSIXFERDONE 0x0800 /* SCSI SCSI transfer done */
+#define SCSIXFERCNT_2_ZERO 0x0100 /* SCSI SCSI transfer count to zero */
+#define SCSIINTERRUPT 0x0080 /* SCSI interrupt pending */
+#define COMMANDABORT 0x0040 /* SCSI command abort */
+#define SEQUENCERACTIVE 0x0020 /* SCSI sequencer active */
+#define PHASEMISMATCH 0x0010 /* SCSI phase mismatch */
+#define PARITYERROR 0x0008 /* SCSI parity error */
+
+#define PHASEMASK 0x0007 /* Phase MSG/CD/IO */
+#define PH_DATA_OUT 0x00 /* Data out phase */
+#define PH_DATA_IN 0x01 /* Data in phase */
+#define PH_COMMAND 0x02 /* Command phase */
+#define PH_STATUS 0x03 /* Status phase */
+#define PH_BUS_FREE 0x05 /* Invalid phase used as bus free */
+#define PH_MSG_OUT 0x06 /* Message out phase */
+#define PH_MSG_IN 0x07 /* Message in phase */
+
+#define TRM_S1040_SCSI_CONTROL 0x80 /* SCSI Control (W) */
+#define DO_CLRATN 0x0400 /* Clear ATN */
+#define DO_SETATN 0x0200 /* Set ATN */
+#define DO_CMDABORT 0x0100 /* Abort SCSI command */
+#define DO_RSTMODULE 0x0010 /* Reset SCSI chip */
+#define DO_RSTSCSI 0x0008 /* Reset SCSI bus */
+#define DO_CLRFIFO 0x0004 /* Clear SCSI transfer FIFO */
+#define DO_DATALATCH 0x0002 /* Enable SCSI bus data input (latched) */
+/* #define DO_DATALATCH 0x0000 */ /* KG: DISable SCSI bus data latch */
+#define DO_HWRESELECT 0x0001 /* Enable hardware reselection */
+
+#define TRM_S1040_SCSI_FIFOCNT 0x82 /* SCSI FIFO Counter 5bits(R) */
+#define TRM_S1040_SCSI_SIGNAL 0x83 /* SCSI low level signal (R/W) */
+
+#define TRM_S1040_SCSI_INTSTATUS 0x84 /* SCSI Interrupt Status (R) */
+#define INT_SCAM 0x80 /* SCAM selection interrupt */
+#define INT_SELECT 0x40 /* Selection interrupt */
+#define INT_SELTIMEOUT 0x20 /* Selection timeout interrupt */
+#define INT_DISCONNECT 0x10 /* Bus disconnected interrupt */
+#define INT_RESELECTED 0x08 /* Reselected interrupt */
+#define INT_SCSIRESET 0x04 /* SCSI reset detected interrupt */
+#define INT_BUSSERVICE 0x02 /* Bus service interrupt */
+#define INT_CMDDONE 0x01 /* SCSI command done interrupt */
+
+#define TRM_S1040_SCSI_OFFSET 0x84 /* SCSI Offset Count (W) */
+
+/************************************************************************/
+/* */
+/* Bit Name Definition */
+/* --------- ------------- ---------------------------- */
+/* 07-05 0 RSVD Reversed. Always 0. */
+/* 04 0 OFFSET4 Reversed for LVDS. Always 0. */
+/* 03-00 0 OFFSET[03:00] Offset number from 0 to 15 */
+/* */
+/************************************************************************/
+
+#define TRM_S1040_SCSI_SYNC 0x85 /* SCSI Synchronous Control (R/W) */
+#define LVDS_SYNC 0x20 /* Enable LVDS synchronous */
+#define WIDE_SYNC 0x10 /* Enable WIDE synchronous */
+#define ALT_SYNC 0x08 /* Enable Fast-20 alternate synchronous */
+
+/************************************************************************/
+/* */
+/* SYNCM 7 6 5 4 3 2 1 0 */
+/* Name RSVD RSVD LVDS WIDE ALTPERD PERIOD2 PERIOD1 PERIOD0 */
+/* Default 0 0 0 0 0 0 0 0 */
+/* */
+/* Bit Name Definition */
+/* --------- ------------- --------------------------- */
+/* 07-06 0 RSVD Reversed. Always read 0 */
+/* 05 0 LVDS Reversed. Always read 0 */
+/* 04 0 WIDE/WSCSI Enable wide (16-bits) SCSI */
+/* transfer. */
+/* 03 0 ALTPERD/ALTPD Alternate (Sync./Period) mode. */
+/* */
+/* @@ When this bit is set, */
+/* the synchronous period bits 2:0 */
+/* in the Synchronous Mode register */
+/* are used to transfer data */
+/* at the Fast-20 rate. */
+/* @@ When this bit is unset, */
+/* the synchronous period bits 2:0 */
+/* in the Synchronous Mode Register */
+/* are used to transfer data */
+/* at the Fast-10 rate (or Fast-40 w/ LVDS). */
+/* */
+/* 02-00 0 PERIOD[2:0]/ Synchronous SCSI Transfer Rate. */
+/* SXPD[02:00] These 3 bits specify */
+/* the Synchronous SCSI Transfer */
+/* Rate for Fast-20 and Fast-10. */
+/* These bits are also reset */
+/* by a SCSI Bus reset. */
+/* */
+/* For Fast-10 bit ALTPD = 0 and LVDS = 0 */
+/* and bit2,bit1,bit0 is defined as follows : */
+/* */
+/* 000 100ns, 10.0 MHz */
+/* 001 150ns, 6.6 MHz */
+/* 010 200ns, 5.0 MHz */
+/* 011 250ns, 4.0 MHz */
+/* 100 300ns, 3.3 MHz */
+/* 101 350ns, 2.8 MHz */
+/* 110 400ns, 2.5 MHz */
+/* 111 450ns, 2.2 MHz */
+/* */
+/* For Fast-20 bit ALTPD = 1 and LVDS = 0 */
+/* and bit2,bit1,bit0 is defined as follows : */
+/* */
+/* 000 50ns, 20.0 MHz */
+/* 001 75ns, 13.3 MHz */
+/* 010 100ns, 10.0 MHz */
+/* 011 125ns, 8.0 MHz */
+/* 100 150ns, 6.6 MHz */
+/* 101 175ns, 5.7 MHz */
+/* 110 200ns, 5.0 MHz */
+/* 111 250ns, 4.0 MHz KG: Maybe 225ns, 4.4 MHz */
+/* */
+/* For Fast-40 bit ALTPD = 0 and LVDS = 1 */
+/* and bit2,bit1,bit0 is defined as follows : */
+/* */
+/* 000 25ns, 40.0 MHz */
+/* 001 50ns, 20.0 MHz */
+/* 010 75ns, 13.3 MHz */
+/* 011 100ns, 10.0 MHz */
+/* 100 125ns, 8.0 MHz */
+/* 101 150ns, 6.6 MHz */
+/* 110 175ns, 5.7 MHz */
+/* 111 200ns, 5.0 MHz */
+/* */
+/************************************************************************/
+
+#define TRM_S1040_SCSI_TARGETID 0x86 /* SCSI Target ID (R/W) */
+#define TRM_S1040_SCSI_IDMSG 0x87 /* SCSI Identify Message (R) */
+#define TRM_S1040_SCSI_HOSTID 0x87 /* SCSI Host ID (W) */
+#define TRM_S1040_SCSI_COUNTER 0x88 /* SCSI Transfer Counter 24bits(R/W) */
+
+#define TRM_S1040_SCSI_INTEN 0x8C /* SCSI Interrupt Enable (R/W) */
+#define EN_SCAM 0x80 /* Enable SCAM selection interrupt */
+#define EN_SELECT 0x40 /* Enable selection interrupt */
+#define EN_SELTIMEOUT 0x20 /* Enable selection timeout interrupt */
+#define EN_DISCONNECT 0x10 /* Enable bus disconnected interrupt */
+#define EN_RESELECTED 0x08 /* Enable reselected interrupt */
+#define EN_SCSIRESET 0x04 /* Enable SCSI reset detected interrupt */
+#define EN_BUSSERVICE 0x02 /* Enable bus service interrupt */
+#define EN_CMDDONE 0x01 /* Enable SCSI command done interrupt */
+
+#define TRM_S1040_SCSI_CONFIG0 0x8D /* SCSI Configuration 0 (R/W) */
+#define PHASELATCH 0x40 /* Enable phase latch */
+#define INITIATOR 0x20 /* Enable initiator mode */
+#define PARITYCHECK 0x10 /* Enable parity check */
+#define BLOCKRST 0x01 /* Disable SCSI reset1 */
+
+#define TRM_S1040_SCSI_CONFIG1 0x8E /* SCSI Configuration 1 (R/W) */
+#define ACTIVE_NEGPLUS 0x10 /* Enhance active negation */
+#define FILTER_DISABLE 0x08 /* Disable SCSI data filter */
+#define FAST_FILTER 0x04 /* ? */
+#define ACTIVE_NEG 0x02 /* Enable active negation */
+
+#define TRM_S1040_SCSI_CONFIG2 0x8F /* SCSI Configuration 2 (R/W) */
+#define CFG2_WIDEFIFO 0x02 /* */
+
+#define TRM_S1040_SCSI_COMMAND 0x90 /* SCSI Command (R/W) */
+#define SCMD_COMP 0x12 /* Command complete */
+#define SCMD_SEL_ATN 0x60 /* Selection with ATN */
+#define SCMD_SEL_ATN3 0x64 /* Selection with ATN3 */
+#define SCMD_SEL_ATNSTOP 0xB8 /* Selection with ATN and Stop */
+#define SCMD_FIFO_OUT 0xC0 /* SCSI FIFO transfer out */
+#define SCMD_DMA_OUT 0xC1 /* SCSI DMA transfer out */
+#define SCMD_FIFO_IN 0xC2 /* SCSI FIFO transfer in */
+#define SCMD_DMA_IN 0xC3 /* SCSI DMA transfer in */
+#define SCMD_MSGACCEPT 0xD8 /* Message accept */
+
+/************************************************************************/
+/* */
+/* Code Command Description */
+/* ---- ---------------------------------------- */
+/* 02 Enable reselection with FIFO */
+/* 40 Select without ATN with FIFO */
+/* 60 Select with ATN with FIFO */
+/* 64 Select with ATN3 with FIFO */
+/* A0 Select with ATN and stop with FIFO */
+/* C0 Transfer information out with FIFO */
+/* C1 Transfer information out with DMA */
+/* C2 Transfer information in with FIFO */
+/* C3 Transfer information in with DMA */
+/* 12 Initiator command complete with FIFO */
+/* 50 Initiator transfer information out sequence without ATN */
+/* with FIFO */
+/* 70 Initiator transfer information out sequence with ATN */
+/* with FIFO */
+/* 74 Initiator transfer information out sequence with ATN3 */
+/* with FIFO */
+/* 52 Initiator transfer information in sequence without ATN */
+/* with FIFO */
+/* 72 Initiator transfer information in sequence with ATN */
+/* with FIFO */
+/* 76 Initiator transfer information in sequence with ATN3 */
+/* with FIFO */
+/* 90 Initiator transfer information out command complete */
+/* with FIFO */
+/* 92 Initiator transfer information in command complete */
+/* with FIFO */
+/* D2 Enable selection */
+/* 08 Reselection */
+/* 48 Disconnect command with FIFO */
+/* 88 Terminate command with FIFO */
+/* C8 Target command complete with FIFO */
+/* 18 SCAM Arbitration/ Selection */
+/* 5A Enable reselection */
+/* 98 Select without ATN with FIFO */
+/* B8 Select with ATN with FIFO */
+/* D8 Message Accepted */
+/* 58 NOP */
+/* */
+/************************************************************************/
+
+#define TRM_S1040_SCSI_TIMEOUT 0x91 /* SCSI Time Out Value (R/W) */
+#define TRM_S1040_SCSI_FIFO 0x98 /* SCSI FIFO (R/W) */
+
+#define TRM_S1040_SCSI_TCR0 0x9C /* SCSI Target Control 0 (R/W) */
+#define TCR0_WIDE_NEGO_DONE 0x8000 /* Wide nego done */
+#define TCR0_SYNC_NEGO_DONE 0x4000 /* Synchronous nego done */
+#define TCR0_ENABLE_LVDS 0x2000 /* Enable LVDS synchronous */
+#define TCR0_ENABLE_WIDE 0x1000 /* Enable WIDE synchronous */
+#define TCR0_ENABLE_ALT 0x0800 /* Enable alternate synchronous */
+#define TCR0_PERIOD_MASK 0x0700 /* Transfer rate */
+
+#define TCR0_DO_WIDE_NEGO 0x0080 /* Do wide NEGO */
+#define TCR0_DO_SYNC_NEGO 0x0040 /* Do sync NEGO */
+#define TCR0_DISCONNECT_EN 0x0020 /* Disconnection enable */
+#define TCR0_OFFSET_MASK 0x001F /* Offset number */
+
+#define TRM_S1040_SCSI_TCR1 0x9E /* SCSI Target Control 1 (R/W) */
+#define MAXTAG_MASK 0x7F00 /* Maximum tags (127) */
+#define NON_TAG_BUSY 0x0080 /* Non tag command active */
+#define ACTTAG_MASK 0x007F /* Active tags */
+
+/************************************************************************/
+/* */
+/* The DMA register offset for TRM_S1040 */
+/* */
+/************************************************************************/
+#define TRM_S1040_DMA_COMMAND 0xA0 /* DMA Command (R/W) */
+#define DMACMD_SG 0x02 /* Enable HW S/G support */
+#define DMACMD_DIR 0x01 /* 1 = read from SCSI write to Host */
+#define XFERDATAIN_SG 0x0103 /* Transfer data in w/ SG */
+#define XFERDATAOUT_SG 0x0102 /* Transfer data out w/ SG */
+#define XFERDATAIN 0x0101 /* Transfer data in w/o SG */
+#define XFERDATAOUT 0x0100 /* Transfer data out w/o SG */
+
+#define TRM_S1040_DMA_FIFOCNT 0xA1 /* DMA FIFO Counter (R) */
+
+#define TRM_S1040_DMA_CONTROL 0xA1 /* DMA Control (W) */
+#define DMARESETMODULE 0x10 /* Reset PCI/DMA module */
+#define STOPDMAXFER 0x08 /* Stop DMA transfer */
+#define ABORTXFER 0x04 /* Abort DMA transfer */
+#define CLRXFIFO 0x02 /* Clear DMA transfer FIFO */
+#define STARTDMAXFER 0x01 /* Start DMA transfer */
+
+#define TRM_S1040_DMA_FIFOSTAT 0xA2 /* DMA FIFO Status (R) */
+
+#define TRM_S1040_DMA_STATUS 0xA3 /* DMA Interrupt Status (R/W) */
+#define XFERPENDING 0x80 /* Transfer pending */
+#define SCSIBUSY 0x40 /* SCSI busy */
+#define GLOBALINT 0x20 /* DMA_INTEN bit 0-4 set */
+#define FORCEDMACOMP 0x10 /* Force DMA transfer complete */
+#define DMAXFERERROR 0x08 /* DMA transfer error */
+#define DMAXFERABORT 0x04 /* DMA transfer abort */
+#define DMAXFERCOMP 0x02 /* Bus Master XFER Complete status */
+#define SCSICOMP 0x01 /* SCSI complete interrupt */
+
+#define TRM_S1040_DMA_INTEN 0xA4 /* DMA Interrupt Enable (R/W) */
+#define EN_FORCEDMACOMP 0x10 /* Force DMA transfer complete */
+#define EN_DMAXFERERROR 0x08 /* DMA transfer error */
+#define EN_DMAXFERABORT 0x04 /* DMA transfer abort */
+#define EN_DMAXFERCOMP 0x02 /* Bus Master XFER Complete status */
+#define EN_SCSIINTR 0x01 /* Enable SCSI complete interrupt */
+
+#define TRM_S1040_DMA_CONFIG 0xA6 /* DMA Configuration (R/W) */
+#define DMA_ENHANCE 0x8000 /* Enable DMA enhance feature (SG?) */
+#define DMA_PCI_DUAL_ADDR 0x4000 /* */
+#define DMA_CFG_RES 0x2000 /* Always 1 */
+#define DMA_AUTO_CLR_FIFO 0x1000 /* DISable DMA auto clear FIFO */
+#define DMA_MEM_MULTI_READ 0x0800 /* */
+#define DMA_MEM_WRITE_INVAL 0x0400 /* Memory write and invalidate */
+#define DMA_FIFO_CTRL 0x0300 /* Control FIFO operation with DMA */
+#define DMA_FIFO_HALF_HALF 0x0200 /* Keep half filled on both read/write */
+
+#define TRM_S1040_DMA_XCNT 0xA8 /* DMA Transfer Counter (R/W), 24bits */
+#define TRM_S1040_DMA_CXCNT 0xAC /* DMA Current Transfer Counter (R) */
+#define TRM_S1040_DMA_XLOWADDR 0xB0 /* DMA Transfer Physical Low Address */
+#define TRM_S1040_DMA_XHIGHADDR 0xB4 /* DMA Transfer Physical High Address */
+
+/************************************************************************/
+/* */
+/* The general register offset for TRM_S1040 */
+/* */
+/************************************************************************/
+#define TRM_S1040_GEN_CONTROL 0xD4 /* Global Control */
+#define CTRL_LED 0x80 /* Control onboard LED */
+#define EN_EEPROM 0x10 /* Enable EEPROM programming */
+#define DIS_TERM 0x08 /* Disable onboard termination */
+#define AUTOTERM 0x04 /* Enable Auto SCSI terminator */
+#define LOW8TERM 0x02 /* Enable Lower 8 bit SCSI terminator */
+#define UP8TERM 0x01 /* Enable Upper 8 bit SCSI terminator */
+
+#define TRM_S1040_GEN_STATUS 0xD5 /* Global Status */
+#define GTIMEOUT 0x80 /* Global timer reach 0 */
+#define EXT68HIGH 0x40 /* Higher 8 bit connected externally */
+#define INT68HIGH 0x20 /* Higher 8 bit connected internally */
+#define CON5068 0x10 /* External 50/68 pin connected (low) */
+#define CON68 0x08 /* Internal 68 pin connected (low) */
+#define CON50 0x04 /* Internal 50 pin connected (low!) */
+#define WIDESCSI 0x02 /* Wide SCSI card */
+#define STATUS_LOAD_DEFAULT 0x01 /* */
+
+#define TRM_S1040_GEN_NVRAM 0xD6 /* Serial NON-VOLATILE RAM port */
+#define NVR_BITOUT 0x08 /* Serial data out */
+#define NVR_BITIN 0x04 /* Serial data in */
+#define NVR_CLOCK 0x02 /* Serial clock */
+#define NVR_SELECT 0x01 /* Serial select */
+
+#define TRM_S1040_GEN_EDATA 0xD7 /* Parallel EEPROM data port */
+#define TRM_S1040_GEN_EADDRESS 0xD8 /* Parallel EEPROM address */
+#define TRM_S1040_GEN_TIMER 0xDB /* Global timer */
+
+/************************************************************************/
+/* */
+/* NvmTarCfg0: Target configuration byte 0 :..pDCB->DevMode */
+/* */
+/************************************************************************/
+#define NTC_DO_WIDE_NEGO 0x20 /* Wide negotiate */
+#define NTC_DO_TAG_QUEUEING 0x10 /* Enable SCSI tag queuing */
+#define NTC_DO_SEND_START 0x08 /* Send start command SPINUP */
+#define NTC_DO_DISCONNECT 0x04 /* Enable SCSI disconnect */
+#define NTC_DO_SYNC_NEGO 0x02 /* Sync negotiation */
+#define NTC_DO_PARITY_CHK 0x01 /* (it sould define at NAC) */
+ /* Parity check enable */
+
+/************************************************************************/
+/* */
+/* Nvram Initiater bits definition */
+/* */
+/************************************************************************/
+#if 0
+#define MORE2_DRV BIT0
+#define GREATER_1G BIT1
+#define RST_SCSI_BUS BIT2
+#define ACTIVE_NEGATION BIT3
+#define NO_SEEK BIT4
+#define LUN_CHECK BIT5
+#endif
+
+/************************************************************************/
+/* */
+/* Nvram Adapter Cfg bits definition */
+/* */
+/************************************************************************/
+#define NAC_SCANLUN 0x20 /* Include LUN as BIOS device */
+#define NAC_POWERON_SCSI_RESET 0x04 /* Power on reset enable */
+#define NAC_GREATER_1G 0x02 /* > 1G support enable */
+#define NAC_GT2DRIVES 0x01 /* Support more than 2 drives */
+/* #define NAC_DO_PARITY_CHK 0x08 */ /* Parity check enable */
+
+#endif