Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/include/asm-sparc/sunbpp.h b/include/asm-sparc/sunbpp.h
new file mode 100644
index 0000000..568db79
--- /dev/null
+++ b/include/asm-sparc/sunbpp.h
@@ -0,0 +1,80 @@
+/* $Id: sunbpp.h,v 1.1 1999/08/08 14:09:49 shadow Exp $
+ * include/asm-sparc/sunbpp.h
+ */
+
+#ifndef _ASM_SPARC_SUNBPP_H
+#define _ASM_SPARC_SUNBPP_H
+
+struct bpp_regs {
+ /* DMA registers */
+ __volatile__ __u32 p_csr; /* DMA Control/Status Register */
+ __volatile__ __u32 p_addr; /* Address Register */
+ __volatile__ __u32 p_bcnt; /* Byte Count Register */
+ __volatile__ __u32 p_tst_csr; /* Test Control/Status (DMA2 only) */
+ /* Parallel Port registers */
+ __volatile__ __u16 p_hcr; /* Hardware Configuration Register */
+ __volatile__ __u16 p_ocr; /* Operation Configuration Register */
+ __volatile__ __u8 p_dr; /* Parallel Data Register */
+ __volatile__ __u8 p_tcr; /* Transfer Control Register */
+ __volatile__ __u8 p_or; /* Output Register */
+ __volatile__ __u8 p_ir; /* Input Register */
+ __volatile__ __u16 p_icr; /* Interrupt Control Register */
+};
+
+/* P_HCR. Time is in increments of SBus clock. */
+#define P_HCR_TEST 0x8000 /* Allows buried counters to be read */
+#define P_HCR_DSW 0x7f00 /* Data strobe width (in ticks) */
+#define P_HCR_DDS 0x007f /* Data setup before strobe (in ticks) */
+
+/* P_OCR. */
+#define P_OCR_MEM_CLR 0x8000
+#define P_OCR_DATA_SRC 0x4000 /* ) */
+#define P_OCR_DS_DSEL 0x2000 /* ) Bidirectional */
+#define P_OCR_BUSY_DSEL 0x1000 /* ) selects */
+#define P_OCR_ACK_DSEL 0x0800 /* ) */
+#define P_OCR_EN_DIAG 0x0400
+#define P_OCR_BUSY_OP 0x0200 /* Busy operation */
+#define P_OCR_ACK_OP 0x0100 /* Ack operation */
+#define P_OCR_SRST 0x0080 /* Reset state machines. Not selfcleaning. */
+#define P_OCR_IDLE 0x0008 /* PP data transfer state machine is idle */
+#define P_OCR_V_ILCK 0x0002 /* Versatec faded. Zebra only. */
+#define P_OCR_EN_VER 0x0001 /* Enable Versatec (0 - enable). Zebra only. */
+
+/* P_TCR */
+#define P_TCR_DIR 0x08
+#define P_TCR_BUSY 0x04
+#define P_TCR_ACK 0x02
+#define P_TCR_DS 0x01 /* Strobe */
+
+/* P_OR */
+#define P_OR_V3 0x20 /* ) */
+#define P_OR_V2 0x10 /* ) on Zebra only */
+#define P_OR_V1 0x08 /* ) */
+#define P_OR_INIT 0x04
+#define P_OR_AFXN 0x02 /* Auto Feed */
+#define P_OR_SLCT_IN 0x01
+
+/* P_IR */
+#define P_IR_PE 0x04
+#define P_IR_SLCT 0x02
+#define P_IR_ERR 0x01
+
+/* P_ICR */
+#define P_DS_IRQ 0x8000 /* RW1 */
+#define P_ACK_IRQ 0x4000 /* RW1 */
+#define P_BUSY_IRQ 0x2000 /* RW1 */
+#define P_PE_IRQ 0x1000 /* RW1 */
+#define P_SLCT_IRQ 0x0800 /* RW1 */
+#define P_ERR_IRQ 0x0400 /* RW1 */
+#define P_DS_IRQ_EN 0x0200 /* RW Always on rising edge */
+#define P_ACK_IRQ_EN 0x0100 /* RW Always on rising edge */
+#define P_BUSY_IRP 0x0080 /* RW 1= rising edge */
+#define P_BUSY_IRQ_EN 0x0040 /* RW */
+#define P_PE_IRP 0x0020 /* RW 1= rising edge */
+#define P_PE_IRQ_EN 0x0010 /* RW */
+#define P_SLCT_IRP 0x0008 /* RW 1= rising edge */
+#define P_SLCT_IRQ_EN 0x0004 /* RW */
+#define P_ERR_IRP 0x0002 /* RW1 1= rising edge */
+#define P_ERR_IRQ_EN 0x0001 /* RW */
+
+#endif /* !(_ASM_SPARC_SUNBPP_H) */