[POWERPC] mpc5200: make dts files conform to generic names recommended practice

Modify mpc5200 dts files to match Open Firmware's Generic Names recommended
practice.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
diff --git a/arch/powerpc/boot/dts/cm5200.dts b/arch/powerpc/boot/dts/cm5200.dts
index 2b88a58..30737ea 100644
--- a/arch/powerpc/boot/dts/cm5200.dts
+++ b/arch/powerpc/boot/dts/cm5200.dts
@@ -47,17 +47,14 @@
 	soc5200@f0000000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		model = "fsl,mpc5200b";
-		compatible = "fsl,mpc5200b";
-		revision = "";			// from bootloader
-		device_type = "soc";
+		compatible = "fsl,mpc5200b-immr";
 		ranges = <0 f0000000 0000c000>;
 		reg = <f0000000 00000100>;
 		bus-frequency = <0>;		// from bootloader
 		system-frequency = <0>;		// from bootloader
 
 		cdm@200 {
-			compatible = "mpc5200b-cdm","mpc5200-cdm";
+			compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm";
 			reg = <200 38>;
 		};
 
@@ -65,11 +62,11 @@
 			// 5200 interrupts are encoded into two levels;
 			interrupt-controller;
 			#interrupt-cells = <3>;
-			compatible = "mpc5200b-pic","mpc5200-pic";
+			compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic";
 			reg = <500 80>;
 		};
 
-		gpt@600 {	// General Purpose Timer
+		timer@600 {	// General Purpose Timer
 			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
 			reg = <600 10>;
 			interrupts = <1 9 0>;
@@ -77,49 +74,49 @@
 			fsl,has-wdt;
 		};
 
-		gpt@610 {	// General Purpose Timer
+		timer@610 {	// General Purpose Timer
 			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
 			reg = <610 10>;
 			interrupts = <1 a 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		gpt@620 {	// General Purpose Timer
+		timer@620 {	// General Purpose Timer
 			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
 			reg = <620 10>;
 			interrupts = <1 b 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		gpt@630 {	// General Purpose Timer
+		timer@630 {	// General Purpose Timer
 			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
 			reg = <630 10>;
 			interrupts = <1 c 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		gpt@640 {	// General Purpose Timer
+		timer@640 {	// General Purpose Timer
 			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
 			reg = <640 10>;
 			interrupts = <1 d 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		gpt@650 {	// General Purpose Timer
+		timer@650 {	// General Purpose Timer
 			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
 			reg = <650 10>;
 			interrupts = <1 e 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		gpt@660 {	// General Purpose Timer
+		timer@660 {	// General Purpose Timer
 			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
 			reg = <660 10>;
 			interrupts = <1 f 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		gpt@670 {	// General Purpose Timer
+		timer@670 {	// General Purpose Timer
 			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
 			reg = <670 10>;
 			interrupts = <1 10 0>;
@@ -127,43 +124,42 @@
 		};
 
 		rtc@800 {	// Real time clock
-			compatible = "mpc5200b-rtc","mpc5200-rtc";
+			compatible = "fsl,mpc5200b-rtc","fsl,mpc5200-rtc";
 			reg = <800 100>;
 			interrupts = <1 5 0 1 6 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
 		gpio@b00 {
-			compatible = "mpc5200b-gpio","mpc5200-gpio";
+			compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio";
 			reg = <b00 40>;
 			interrupts = <1 7 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		gpio-wkup@c00 {
-			compatible = "mpc5200b-gpio-wkup","mpc5200-gpio-wkup";
+		gpio@c00 {
+			compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup";
 			reg = <c00 40>;
 			interrupts = <1 8 0 0 3 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
 		spi@f00 {
-			compatible = "mpc5200b-spi","mpc5200-spi";
+			compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
 			reg = <f00 20>;
 			interrupts = <2 d 0 2 e 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
 		usb@1000 {
-			device_type = "usb-ohci-be";
-			compatible = "mpc5200b-ohci","mpc5200-ohci","ohci-be";
+			compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be";
 			reg = <1000 ff>;
 			interrupts = <2 6 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
 		dma-controller@1200 {
-			compatible = "mpc5200b-bestcomm","mpc5200-bestcomm";
+			compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm";
 			reg = <1200 80>;
 			interrupts = <3 0 0  3 1 0  3 2 0  3 3 0
 			              3 4 0  3 5 0  3 6 0  3 7 0
@@ -173,13 +169,13 @@
 		};
 
 		xlb@1f00 {
-			compatible = "mpc5200b-xlb","mpc5200-xlb";
+			compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb";
 			reg = <1f00 100>;
 		};
 
 		serial@2000 {		// PSC1
 			device_type = "serial";
-			compatible = "mpc5200b-psc-uart","mpc5200-psc-uart";
+			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
 			port-number = <0>;  // Logical port assignment
 			reg = <2000 100>;
 			interrupts = <2 1 0>;
@@ -188,7 +184,7 @@
 
 		serial@2200 {		// PSC2
 			device_type = "serial";
-			compatible = "mpc5200-psc-uart";
+			compatible = "fsl,mpc5200-psc-uart";
 			port-number = <1>;  // Logical port assignment
 			reg = <2200 100>;
 			interrupts = <2 2 0>;
@@ -197,7 +193,7 @@
 
 		serial@2400 {		// PSC3
 			device_type = "serial";
-			compatible = "mpc5200-psc-uart";
+			compatible = "fsl,mpc5200-psc-uart";
 			port-number = <2>;  // Logical port assignment
 			reg = <2400 100>;
 			interrupts = <2 3 0>;
@@ -206,7 +202,7 @@
 
 		serial@2c00 {		// PSC6
 			device_type = "serial";
-			compatible = "mpc5200b-psc-uart","mpc5200-psc-uart";
+			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
 			port-number = <5>;  // Logical port assignment
 			reg = <2c00 100>;
 			interrupts = <2 4 0>;
@@ -215,15 +211,15 @@
 
 		ethernet@3000 {
 			device_type = "network";
-			compatible = "mpc5200b-fec","mpc5200-fec";
+			compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
 			reg = <3000 800>;
-			local-mac-address = [ 00 00 00 00 00 00 ]; /* Filled in by U-Boot */
+			local-mac-address = [ 00 00 00 00 00 00 ];
 			interrupts = <2 5 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
 		i2c@3d40 {
-			compatible = "mpc5200b-i2c","mpc5200-i2c","fsl-i2c";
+			compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
 			reg = <3d40 40>;
 			interrupts = <2 10 0>;
 			interrupt-parent = <&mpc5200_pic>;
@@ -231,7 +227,7 @@
 		};
 
 		sram@8000 {
-			compatible = "mpc5200b-sram","mpc5200-sram";
+			compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram";
 			reg = <8000 4000>;
 		};
 	};
diff --git a/arch/powerpc/boot/dts/lite5200.dts b/arch/powerpc/boot/dts/lite5200.dts
index 7de3d21..0d701c1 100644
--- a/arch/powerpc/boot/dts/lite5200.dts
+++ b/arch/powerpc/boot/dts/lite5200.dts
@@ -10,15 +10,8 @@
  * option) any later version.
  */
 
-/*
- * WARNING: Do not depend on this tree layout remaining static just yet.
- * The MPC5200 device tree conventions are still in flux
- * Keep an eye on the linuxppc-dev mailing list for more details
- */
-
 / {
 	model = "fsl,lite5200";
-	// revision = "1.0";
 	compatible = "fsl,lite5200";
 	#address-cells = <1>;
 	#size-cells = <1>;
@@ -48,30 +41,27 @@
 	soc5200@f0000000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		model = "fsl,mpc5200";
-		compatible = "mpc5200";
-		revision = "";			// from bootloader
-		device_type = "soc";
+		compatible = "fsl,mpc5200-immr";
 		ranges = <0 f0000000 0000c000>;
 		reg = <f0000000 00000100>;
 		bus-frequency = <0>;		// from bootloader
 		system-frequency = <0>;		// from bootloader
 
 		cdm@200 {
-			compatible = "mpc5200-cdm";
+			compatible = "fsl,mpc5200-cdm";
 			reg = <200 38>;
 		};
 
-		mpc5200_pic: pic@500 {
+		mpc5200_pic: interrupt-controller@500 {
 			// 5200 interrupts are encoded into two levels;
 			interrupt-controller;
 			#interrupt-cells = <3>;
 			device_type = "interrupt-controller";
-			compatible = "mpc5200-pic";
+			compatible = "fsl,mpc5200-pic";
 			reg = <500 80>;
 		};
 
-		gpt@600 {	// General Purpose Timer
+		timer@600 {	// General Purpose Timer
 			compatible = "fsl,mpc5200-gpt";
 			cell-index = <0>;
 			reg = <600 10>;
@@ -80,7 +70,7 @@
 			fsl,has-wdt;
 		};
 
-		gpt@610 {	// General Purpose Timer
+		timer@610 {	// General Purpose Timer
 			compatible = "fsl,mpc5200-gpt";
 			cell-index = <1>;
 			reg = <610 10>;
@@ -88,7 +78,7 @@
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		gpt@620 {	// General Purpose Timer
+		timer@620 {	// General Purpose Timer
 			compatible = "fsl,mpc5200-gpt";
 			cell-index = <2>;
 			reg = <620 10>;
@@ -96,7 +86,7 @@
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		gpt@630 {	// General Purpose Timer
+		timer@630 {	// General Purpose Timer
 			compatible = "fsl,mpc5200-gpt";
 			cell-index = <3>;
 			reg = <630 10>;
@@ -104,7 +94,7 @@
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		gpt@640 {	// General Purpose Timer
+		timer@640 {	// General Purpose Timer
 			compatible = "fsl,mpc5200-gpt";
 			cell-index = <4>;
 			reg = <640 10>;
@@ -112,7 +102,7 @@
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		gpt@650 {	// General Purpose Timer
+		timer@650 {	// General Purpose Timer
 			compatible = "fsl,mpc5200-gpt";
 			cell-index = <5>;
 			reg = <650 10>;
@@ -120,7 +110,7 @@
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		gpt@660 {	// General Purpose Timer
+		timer@660 {	// General Purpose Timer
 			compatible = "fsl,mpc5200-gpt";
 			cell-index = <6>;
 			reg = <660 10>;
@@ -128,7 +118,7 @@
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		gpt@670 {	// General Purpose Timer
+		timer@670 {	// General Purpose Timer
 			compatible = "fsl,mpc5200-gpt";
 			cell-index = <7>;
 			reg = <670 10>;
@@ -137,25 +127,23 @@
 		};
 
 		rtc@800 {	// Real time clock
-			compatible = "mpc5200-rtc";
+			compatible = "fsl,mpc5200-rtc";
 			device_type = "rtc";
 			reg = <800 100>;
 			interrupts = <1 5 0 1 6 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		mscan@900 {
-			device_type = "mscan";
-			compatible = "mpc5200-mscan";
+		can@900 {
+			compatible = "fsl,mpc5200-mscan";
 			cell-index = <0>;
 			interrupts = <2 11 0>;
 			interrupt-parent = <&mpc5200_pic>;
 			reg = <900 80>;
 		};
 
-		mscan@980 {
-			device_type = "mscan";
-			compatible = "mpc5200-mscan";
+		can@980 {
+			compatible = "fsl,mpc5200-mscan";
 			cell-index = <1>;
 			interrupts = <2 12 0>;
 			interrupt-parent = <&mpc5200_pic>;
@@ -163,38 +151,36 @@
 		};
 
 		gpio@b00 {
-			compatible = "mpc5200-gpio";
+			compatible = "fsl,mpc5200-gpio";
 			reg = <b00 40>;
 			interrupts = <1 7 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		gpio-wkup@c00 {
-			compatible = "mpc5200-gpio-wkup";
+		gpio@c00 {
+			compatible = "fsl,mpc5200-gpio-wkup";
 			reg = <c00 40>;
 			interrupts = <1 8 0 0 3 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
 		spi@f00 {
-			device_type = "spi";
-			compatible = "mpc5200-spi";
+			compatible = "fsl,mpc5200-spi";
 			reg = <f00 20>;
 			interrupts = <2 d 0 2 e 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
 		usb@1000 {
-			device_type = "usb-ohci-be";
-			compatible = "mpc5200-ohci","ohci-be";
+			compatible = "fsl,mpc5200-ohci","ohci-be";
 			reg = <1000 ff>;
 			interrupts = <2 6 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		bestcomm@1200 {
+		dma-controller@1200 {
 			device_type = "dma-controller";
-			compatible = "mpc5200-bestcomm";
+			compatible = "fsl,mpc5200-bestcomm";
 			reg = <1200 80>;
 			interrupts = <3 0 0  3 1 0  3 2 0  3 3 0
 			              3 4 0  3 5 0  3 6 0  3 7 0
@@ -204,13 +190,13 @@
 		};
 
 		xlb@1f00 {
-			compatible = "mpc5200-xlb";
+			compatible = "fsl,mpc5200-xlb";
 			reg = <1f00 100>;
 		};
 
 		serial@2000 {		// PSC1
 			device_type = "serial";
-			compatible = "mpc5200-psc-uart";
+			compatible = "fsl,mpc5200-psc-uart";
 			port-number = <0>;  // Logical port assignment
 			cell-index = <0>;
 			reg = <2000 100>;
@@ -220,8 +206,7 @@
 
 		// PSC2 in ac97 mode example
 		//ac97@2200 {		// PSC2
-		//	device_type = "sound";
-		//	compatible = "mpc5200-psc-ac97";
+		//	compatible = "fsl,mpc5200-psc-ac97";
 		//	cell-index = <1>;
 		//	reg = <2200 100>;
 		//	interrupts = <2 2 0>;
@@ -230,8 +215,7 @@
 
 		// PSC3 in CODEC mode example
 		//i2s@2400 {		// PSC3
-		//	device_type = "sound";
-		//	compatible = "mpc5200-psc-i2s";
+		//	compatible = "fsl,mpc5200-psc-i2s";
 		//	cell-index = <2>;
 		//	reg = <2400 100>;
 		//	interrupts = <2 3 0>;
@@ -241,7 +225,7 @@
 		// PSC4 in uart mode example
 		//serial@2600 {		// PSC4
 		//	device_type = "serial";
-		//	compatible = "mpc5200-psc-uart";
+		//	compatible = "fsl,mpc5200-psc-uart";
 		//	cell-index = <3>;
 		//	reg = <2600 100>;
 		//	interrupts = <2 b 0>;
@@ -251,7 +235,7 @@
 		// PSC5 in uart mode example
 		//serial@2800 {		// PSC5
 		//	device_type = "serial";
-		//	compatible = "mpc5200-psc-uart";
+		//	compatible = "fsl,mpc5200-psc-uart";
 		//	cell-index = <4>;
 		//	reg = <2800 100>;
 		//	interrupts = <2 c 0>;
@@ -260,8 +244,7 @@
 
 		// PSC6 in spi mode example
 		//spi@2c00 {		// PSC6
-		//	device_type = "spi";
-		//	compatible = "mpc5200-psc-spi";
+		//	compatible = "fsl,mpc5200-psc-spi";
 		//	cell-index = <5>;
 		//	reg = <2c00 100>;
 		//	interrupts = <2 4 0>;
@@ -270,16 +253,16 @@
 
 		ethernet@3000 {
 			device_type = "network";
-			compatible = "mpc5200-fec";
+			compatible = "fsl,mpc5200-fec";
 			reg = <3000 800>;
-			mac-address = [ 02 03 04 05 06 07 ]; // Bad!
+			local-mac-address = [ 00 00 00 00 00 00 ];
 			interrupts = <2 5 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
 		ata@3a00 {
 			device_type = "ata";
-			compatible = "mpc5200-ata";
+			compatible = "fsl,mpc5200-ata";
 			reg = <3a00 100>;
 			interrupts = <2 7 0>;
 			interrupt-parent = <&mpc5200_pic>;
@@ -288,7 +271,7 @@
 		i2c@3d00 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "mpc5200-i2c","fsl-i2c";
+			compatible = "fsl,mpc5200-i2c","fsl-i2c";
 			cell-index = <0>;
 			reg = <3d00 40>;
 			interrupts = <2 f 0>;
@@ -299,7 +282,7 @@
 		i2c@3d40 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "mpc5200-i2c","fsl-i2c";
+			compatible = "fsl,mpc5200-i2c","fsl-i2c";
 			cell-index = <1>;
 			reg = <3d40 40>;
 			interrupts = <2 10 0>;
@@ -307,8 +290,7 @@
 			fsl5200-clocking;
 		};
 		sram@8000 {
-			device_type = "sram";
-			compatible = "mpc5200-sram","sram";
+			compatible = "fsl,mpc5200-sram","sram";
 			reg = <8000 4000>;
 		};
 	};
@@ -318,7 +300,7 @@
 		#size-cells = <2>;
 		#address-cells = <3>;
 		device_type = "pci";
-		compatible = "mpc5200-pci";
+		compatible = "fsl,mpc5200-pci";
 		reg = <f0000d00 100>;
 		interrupt-map-mask = <f800 0 0 7>;
 		interrupt-map = <c000 0 0 1 &mpc5200_pic 0 0 3
diff --git a/arch/powerpc/boot/dts/lite5200b.dts b/arch/powerpc/boot/dts/lite5200b.dts
index dd2c4fd..571ba02 100644
--- a/arch/powerpc/boot/dts/lite5200b.dts
+++ b/arch/powerpc/boot/dts/lite5200b.dts
@@ -18,7 +18,6 @@
 
 / {
 	model = "fsl,lite5200b";
-	// revision = "1.0";
 	compatible = "fsl,lite5200b";
 	#address-cells = <1>;
 	#size-cells = <1>;
@@ -48,30 +47,27 @@
 	soc5200@f0000000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		model = "fsl,mpc5200b";
-		compatible = "mpc5200";
-		revision = "";			// from bootloader
-		device_type = "soc";
+		compatible = "fsl,mpc5200b-immr";
 		ranges = <0 f0000000 0000c000>;
 		reg = <f0000000 00000100>;
 		bus-frequency = <0>;		// from bootloader
 		system-frequency = <0>;		// from bootloader
 
 		cdm@200 {
-			compatible = "mpc5200b-cdm","mpc5200-cdm";
+			compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm";
 			reg = <200 38>;
 		};
 
-		mpc5200_pic: pic@500 {
+		mpc5200_pic: interrupt-controller@500 {
 			// 5200 interrupts are encoded into two levels;
 			interrupt-controller;
 			#interrupt-cells = <3>;
 			device_type = "interrupt-controller";
-			compatible = "mpc5200b-pic","mpc5200-pic";
+			compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic";
 			reg = <500 80>;
 		};
 
-		gpt@600 {	// General Purpose Timer
+		timer@600 {	// General Purpose Timer
 			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
 			cell-index = <0>;
 			reg = <600 10>;
@@ -80,7 +76,7 @@
 			fsl,has-wdt;
 		};
 
-		gpt@610 {	// General Purpose Timer
+		timer@610 {	// General Purpose Timer
 			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
 			cell-index = <1>;
 			reg = <610 10>;
@@ -88,7 +84,7 @@
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		gpt@620 {	// General Purpose Timer
+		timer@620 {	// General Purpose Timer
 			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
 			cell-index = <2>;
 			reg = <620 10>;
@@ -96,7 +92,7 @@
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		gpt@630 {	// General Purpose Timer
+		timer@630 {	// General Purpose Timer
 			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
 			cell-index = <3>;
 			reg = <630 10>;
@@ -104,7 +100,7 @@
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		gpt@640 {	// General Purpose Timer
+		timer@640 {	// General Purpose Timer
 			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
 			cell-index = <4>;
 			reg = <640 10>;
@@ -112,7 +108,7 @@
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		gpt@650 {	// General Purpose Timer
+		timer@650 {	// General Purpose Timer
 			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
 			cell-index = <5>;
 			reg = <650 10>;
@@ -120,7 +116,7 @@
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		gpt@660 {	// General Purpose Timer
+		timer@660 {	// General Purpose Timer
 			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
 			cell-index = <6>;
 			reg = <660 10>;
@@ -128,7 +124,7 @@
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		gpt@670 {	// General Purpose Timer
+		timer@670 {	// General Purpose Timer
 			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
 			cell-index = <7>;
 			reg = <670 10>;
@@ -137,25 +133,23 @@
 		};
 
 		rtc@800 {	// Real time clock
-			compatible = "mpc5200b-rtc","mpc5200-rtc";
+			compatible = "fsl,mpc5200b-rtc","fsl,mpc5200-rtc";
 			device_type = "rtc";
 			reg = <800 100>;
 			interrupts = <1 5 0 1 6 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		mscan@900 {
-			device_type = "mscan";
-			compatible = "mpc5200b-mscan","mpc5200-mscan";
+		can@900 {
+			compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan";
 			cell-index = <0>;
 			interrupts = <2 11 0>;
 			interrupt-parent = <&mpc5200_pic>;
 			reg = <900 80>;
 		};
 
-		mscan@980 {
-			device_type = "mscan";
-			compatible = "mpc5200b-mscan","mpc5200-mscan";
+		can@980 {
+			compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan";
 			cell-index = <1>;
 			interrupts = <2 12 0>;
 			interrupt-parent = <&mpc5200_pic>;
@@ -163,38 +157,36 @@
 		};
 
 		gpio@b00 {
-			compatible = "mpc5200b-gpio","mpc5200-gpio";
+			compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio";
 			reg = <b00 40>;
 			interrupts = <1 7 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		gpio-wkup@c00 {
-			compatible = "mpc5200b-gpio-wkup","mpc5200-gpio-wkup";
+		gpio@c00 {
+			compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup";
 			reg = <c00 40>;
 			interrupts = <1 8 0 0 3 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
 		spi@f00 {
-			device_type = "spi";
-			compatible = "mpc5200b-spi","mpc5200-spi";
+			compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
 			reg = <f00 20>;
 			interrupts = <2 d 0 2 e 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
 		usb@1000 {
-			device_type = "usb-ohci-be";
-			compatible = "mpc5200b-ohci","mpc5200-ohci","ohci-be";
+			compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be";
 			reg = <1000 ff>;
 			interrupts = <2 6 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		bestcomm@1200 {
+		dma-controller@1200 {
 			device_type = "dma-controller";
-			compatible = "mpc5200b-bestcomm","mpc5200-bestcomm";
+			compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm";
 			reg = <1200 80>;
 			interrupts = <3 0 0  3 1 0  3 2 0  3 3 0
 			              3 4 0  3 5 0  3 6 0  3 7 0
@@ -204,13 +196,13 @@
 		};
 
 		xlb@1f00 {
-			compatible = "mpc5200b-xlb","mpc5200-xlb";
+			compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb";
 			reg = <1f00 100>;
 		};
 
 		serial@2000 {		// PSC1
 			device_type = "serial";
-			compatible = "mpc5200b-psc-uart","mpc5200-psc-uart";
+			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
 			port-number = <0>;  // Logical port assignment
 			cell-index = <0>;
 			reg = <2000 100>;
@@ -220,8 +212,7 @@
 
 		// PSC2 in ac97 mode example
 		//ac97@2200 {		// PSC2
-		//	device_type = "sound";
-		//	compatible = "mpc5200b-psc-ac97","mpc5200-psc-ac97";
+		//	compatible = "fsl,mpc5200b-psc-ac97","fsl,mpc5200-psc-ac97";
 		//	cell-index = <1>;
 		//	reg = <2200 100>;
 		//	interrupts = <2 2 0>;
@@ -230,8 +221,7 @@
 
 		// PSC3 in CODEC mode example
 		//i2s@2400 {		// PSC3
-		//	device_type = "sound";
-		//	compatible = "mpc5200b-psc-i2s"; //not 5200 compatible
+		//	compatible = "fsl,mpc5200b-psc-i2s"; //not 5200 compatible
 		//	cell-index = <2>;
 		//	reg = <2400 100>;
 		//	interrupts = <2 3 0>;
@@ -241,7 +231,7 @@
 		// PSC4 in uart mode example
 		//serial@2600 {		// PSC4
 		//	device_type = "serial";
-		//	compatible = "mpc5200b-psc-uart","mpc5200-psc-uart";
+		//	compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
 		//	cell-index = <3>;
 		//	reg = <2600 100>;
 		//	interrupts = <2 b 0>;
@@ -251,7 +241,7 @@
 		// PSC5 in uart mode example
 		//serial@2800 {		// PSC5
 		//	device_type = "serial";
-		//	compatible = "mpc5200b-psc-uart","mpc5200-psc-uart";
+		//	compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
 		//	cell-index = <4>;
 		//	reg = <2800 100>;
 		//	interrupts = <2 c 0>;
@@ -260,8 +250,7 @@
 
 		// PSC6 in spi mode example
 		//spi@2c00 {		// PSC6
-		//	device_type = "spi";
-		//	compatible = "mpc5200b-psc-spi","mpc5200-psc-spi";
+		//	compatible = "fsl,mpc5200b-psc-spi","fsl,mpc5200-psc-spi";
 		//	cell-index = <5>;
 		//	reg = <2c00 100>;
 		//	interrupts = <2 4 0>;
@@ -270,9 +259,9 @@
 
 		ethernet@3000 {
 			device_type = "network";
-			compatible = "mpc5200b-fec","mpc5200-fec";
+			compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
 			reg = <3000 400>;
-			mac-address = [ 02 03 04 05 06 07 ]; // Bad!
+			local-mac-address = [ 00 00 00 00 00 00 ];
 			interrupts = <2 5 0>;
 			interrupt-parent = <&mpc5200_pic>;
 			phy-handle = <&phy0>;
@@ -281,8 +270,7 @@
 		mdio@3000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			device_type = "mdio";
-			compatible = "mpc5200b-fec-phy";
+			compatible = "fsl,mpc5200b-mdio";
 			reg = <3000 400>;	// fec range, since we need to setup fec interrupts
 			interrupts = <2 5 0>;	// these are for "mii command finished", not link changes & co.
 			interrupt-parent = <&mpc5200_pic>;
@@ -295,7 +283,7 @@
 
 		ata@3a00 {
 			device_type = "ata";
-			compatible = "mpc5200b-ata","mpc5200-ata";
+			compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata";
 			reg = <3a00 100>;
 			interrupts = <2 7 0>;
 			interrupt-parent = <&mpc5200_pic>;
@@ -304,7 +292,7 @@
 		i2c@3d00 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "mpc5200b-i2c","mpc5200-i2c","fsl-i2c";
+			compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
 			cell-index = <0>;
 			reg = <3d00 40>;
 			interrupts = <2 f 0>;
@@ -315,7 +303,7 @@
 		i2c@3d40 {
 			#address-cells = <1>;
 			#size-cells = <0>;
-			compatible = "mpc5200b-i2c","mpc5200-i2c","fsl-i2c";
+			compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
 			cell-index = <1>;
 			reg = <3d40 40>;
 			interrupts = <2 10 0>;
@@ -323,8 +311,7 @@
 			fsl5200-clocking;
 		};
 		sram@8000 {
-			device_type = "sram";
-			compatible = "mpc5200b-sram","mpc5200-sram","sram";
+			compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram","sram";
 			reg = <8000 4000>;
 		};
 	};
@@ -334,7 +321,7 @@
 		#size-cells = <2>;
 		#address-cells = <3>;
 		device_type = "pci";
-		compatible = "mpc5200b-pci","mpc5200-pci";
+		compatible = "fsl,mpc5200b-pci","fsl,mpc5200-pci";
 		reg = <f0000d00 100>;
 		interrupt-map-mask = <f800 0 0 7>;
 		interrupt-map = <c000 0 0 1 &mpc5200_pic 0 0 3 // 1st slot
diff --git a/arch/powerpc/boot/dts/motionpro.dts b/arch/powerpc/boot/dts/motionpro.dts
index ee30805..76951ab 100644
--- a/arch/powerpc/boot/dts/motionpro.dts
+++ b/arch/powerpc/boot/dts/motionpro.dts
@@ -10,12 +10,6 @@
  * option) any later version.
  */
 
-/*
- * WARNING: Do not depend on this tree layout remaining static just yet.
- * The MPC5200 device tree conventions are still in flux
- * Keep an eye on the linuxppc-dev mailing list for more details
- */
-
 / {
 	model = "promess,motionpro";
 	compatible = "promess,motionpro";
@@ -47,29 +41,26 @@
 	soc5200@f0000000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		model = "fsl,mpc5200b";
-		compatible = "fsl,mpc5200b";
-		revision = "";			// from bootloader
-		device_type = "soc";
+		compatible = "fsl,mpc5200b-immr";
 		ranges = <0 f0000000 0000c000>;
 		reg = <f0000000 00000100>;
 		bus-frequency = <0>;		// from bootloader
 		system-frequency = <0>;		// from bootloader
 
 		cdm@200 {
-			compatible = "mpc5200b-cdm","mpc5200-cdm";
+			compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm";
 			reg = <200 38>;
 		};
 
-		mpc5200_pic: pic@500 {
+		mpc5200_pic: interrupt-controller@500 {
 			// 5200 interrupts are encoded into two levels;
 			interrupt-controller;
 			#interrupt-cells = <3>;
-			compatible = "mpc5200b-pic","mpc5200-pic";
+			compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic";
 			reg = <500 80>;
 		};
 
-		gpt@600 {	// General Purpose Timer
+		timer@600 {	// General Purpose Timer
 			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
 			reg = <600 10>;
 			interrupts = <1 9 0>;
@@ -77,35 +68,35 @@
 			fsl,has-wdt;
 		};
 
-		gpt@610 {	// General Purpose Timer
+		timer@610 {	// General Purpose Timer
 			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
 			reg = <610 10>;
 			interrupts = <1 a 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		gpt@620 {	// General Purpose Timer
+		timer@620 {	// General Purpose Timer
 			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
 			reg = <620 10>;
 			interrupts = <1 b 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		gpt@630 {	// General Purpose Timer
+		timer@630 {	// General Purpose Timer
 			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
 			reg = <630 10>;
 			interrupts = <1 c 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		gpt@640 {	// General Purpose Timer
+		timer@640 {	// General Purpose Timer
 			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
 			reg = <640 10>;
 			interrupts = <1 d 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		gpt@650 {	// General Purpose Timer
+		timer@650 {	// General Purpose Timer
 			compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
 			reg = <650 10>;
 			interrupts = <1 e 0>;
@@ -130,28 +121,28 @@
 		};
 
 		rtc@800 {	// Real time clock
-			compatible = "mpc5200b-rtc","mpc5200-rtc";
+			compatible = "fsl,mpc5200b-rtc","fsl,mpc5200-rtc";
 			reg = <800 100>;
 			interrupts = <1 5 0 1 6 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
 		mscan@980 {
-			compatible = "mpc5200b-mscan","mpc5200-mscan";
+			compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan";
 			interrupts = <2 12 0>;
 			interrupt-parent = <&mpc5200_pic>;
 			reg = <980 80>;
 		};
 
 		gpio@b00 {
-			compatible = "mpc5200b-gpio","mpc5200-gpio";
+			compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio";
 			reg = <b00 40>;
 			interrupts = <1 7 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
-		gpio-wkup@c00 {
-			compatible = "mpc5200b-gpio-wkup","mpc5200-gpio-wkup";
+		gpio@c00 {
+			compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup";
 			reg = <c00 40>;
 			interrupts = <1 8 0 0 3 0>;
 			interrupt-parent = <&mpc5200_pic>;
@@ -159,21 +150,21 @@
 
 
 		spi@f00 {
-			compatible = "mpc5200b-spi","mpc5200-spi";
+			compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
 			reg = <f00 20>;
 			interrupts = <2 d 0 2 e 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
 		usb@1000 {
-			compatible = "mpc5200b-ohci","mpc5200-ohci","ohci-be";
+			compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be";
 			reg = <1000 ff>;
 			interrupts = <2 6 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
 		dma-controller@1200 {
-			compatible = "mpc5200b-bestcomm","mpc5200-bestcomm";
+			compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm";
 			reg = <1200 80>;
 			interrupts = <3 0 0  3 1 0  3 2 0  3 3 0
 			              3 4 0  3 5 0  3 6 0  3 7 0
@@ -183,13 +174,13 @@
 		};
 
 		xlb@1f00 {
-			compatible = "mpc5200b-xlb","mpc5200-xlb";
+			compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb";
 			reg = <1f00 100>;
 		};
 
 		serial@2000 {		// PSC1
 			device_type = "serial";
-			compatible = "mpc5200b-psc-uart","mpc5200-psc-uart";
+			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
 			port-number = <0>;  // Logical port assignment
 			reg = <2000 100>;
 			interrupts = <2 1 0>;
@@ -198,7 +189,7 @@
 
 		// PSC2 in spi master mode 
 		spi@2200 {		// PSC2
-			compatible = "mpc5200b-psc-spi","mpc5200-psc-spi";
+			compatible = "fsl,mpc5200b-psc-spi","fsl,mpc5200-psc-spi";
 			cell-index = <1>;
 			reg = <2200 100>;
 			interrupts = <2 2 0>;
@@ -208,7 +199,7 @@
 		// PSC5 in uart mode
 		serial@2800 {		// PSC5
 			device_type = "serial";
-			compatible = "mpc5200b-psc-uart","mpc5200-psc-uart";
+			compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
 			port-number = <4>;  // Logical port assignment
 			reg = <2800 100>;
 			interrupts = <2 c 0>;
@@ -217,22 +208,22 @@
 
 		ethernet@3000 {
 			device_type = "network";
-			compatible = "mpc5200b-fec","mpc5200-fec";
+			compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
 			reg = <3000 800>;
-			local-mac-address = [ 00 00 00 00 00 00 ]; /* Filled in by U-Boot */
+			local-mac-address = [ 00 00 00 00 00 00 ];
 			interrupts = <2 5 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
 		ata@3a00 {
-			compatible = "mpc5200b-ata","mpc5200-ata";
+			compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata";
 			reg = <3a00 100>;
 			interrupts = <2 7 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
 		i2c@3d40 {
-			compatible = "mpc5200b-i2c","mpc5200-i2c","fsl-i2c";
+			compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
 			reg = <3d40 40>;
 			interrupts = <2 10 0>;
 			interrupt-parent = <&mpc5200_pic>;
@@ -240,13 +231,12 @@
 		};
 
 		sram@8000 {
-			compatible = "mpc5200b-sram","mpc5200-sram";
+			compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram";
 			reg = <8000 4000>;
 		};
 	};
 
 	lpb {
-		model = "fsl,lpb";
 		compatible = "fsl,lpb";
 		#address-cells = <2>;
 		#size-cells = <1>;
@@ -288,7 +278,7 @@
 		#size-cells = <2>;
 		#address-cells = <3>;
 		device_type = "pci";
-		compatible = "mpc5200b-pci","mpc5200-pci";
+		compatible = "fsl,mpc5200b-pci","fsl,mpc5200-pci";
 		reg = <f0000d00 100>;
 		interrupt-map-mask = <f800 0 0 7>;
 		interrupt-map = <c000 0 0 1 &mpc5200_pic 0 0 3 // 1st slot
diff --git a/arch/powerpc/boot/dts/tqm5200.dts b/arch/powerpc/boot/dts/tqm5200.dts
index 58c9799..c86464f 100644
--- a/arch/powerpc/boot/dts/tqm5200.dts
+++ b/arch/powerpc/boot/dts/tqm5200.dts
@@ -10,12 +10,6 @@
  * option) any later version.
  */
 
-/*
- * WARNING: Do not depend on this tree layout remaining static just yet.
- * The MPC5200 device tree conventions are still in flux
- * Keep an eye on the linuxppc-dev mailing list for more details
- */
-
 / {
 	model = "tqc,tqm5200";
 	compatible = "tqc,tqm5200";
@@ -47,29 +41,26 @@
 	soc5200@f0000000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		model = "fsl,mpc5200";
-		compatible = "fsl,mpc5200";
-		revision = "";			// from bootloader
-		device_type = "soc";
+		compatible = "fsl,mpc5200-immr";
 		ranges = <0 f0000000 0000c000>;
 		reg = <f0000000 00000100>;
 		bus-frequency = <0>;		// from bootloader
 		system-frequency = <0>;		// from bootloader
 
 		cdm@200 {
-			compatible = "mpc5200-cdm";
+			compatible = "fsl,mpc5200-cdm";
 			reg = <200 38>;
 		};
 
-		mpc5200_pic: pic@500 {
+		mpc5200_pic: interrupt-controller@500 {
 			// 5200 interrupts are encoded into two levels;
 			interrupt-controller;
 			#interrupt-cells = <3>;
-			compatible = "mpc5200-pic";
+			compatible = "fsl,mpc5200-pic";
 			reg = <500 80>;
 		};
 
-		gpt@600 {	// General Purpose Timer
+		timer@600 {	// General Purpose Timer
 			compatible = "fsl,mpc5200-gpt";
 			reg = <600 10>;
 			interrupts = <1 9 0>;
@@ -78,21 +69,21 @@
 		};
 
 		gpio@b00 {
-			compatible = "mpc5200-gpio";
+			compatible = "fsl,mpc5200-gpio";
 			reg = <b00 40>;
 			interrupts = <1 7 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
 		usb@1000 {
-			compatible = "mpc5200-ohci","ohci-be";
+			compatible = "fsl,mpc5200-ohci","ohci-be";
 			reg = <1000 ff>;
 			interrupts = <2 6 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
 		dma-controller@1200 {
-			compatible = "mpc5200-bestcomm";
+			compatible = "fsl,mpc5200-bestcomm";
 			reg = <1200 80>;
 			interrupts = <3 0 0  3 1 0  3 2 0  3 3 0
 			              3 4 0  3 5 0  3 6 0  3 7 0
@@ -102,13 +93,13 @@
 		};
 
 		xlb@1f00 {
-			compatible = "mpc5200-xlb";
+			compatible = "fsl,mpc5200-xlb";
 			reg = <1f00 100>;
 		};
 
 		serial@2000 {		// PSC1
 			device_type = "serial";
-			compatible = "mpc5200-psc-uart";
+			compatible = "fsl,mpc5200-psc-uart";
 			port-number = <0>;  // Logical port assignment
 			reg = <2000 100>;
 			interrupts = <2 1 0>;
@@ -117,7 +108,7 @@
 
 		serial@2200 {		// PSC2
 			device_type = "serial";
-			compatible = "mpc5200-psc-uart";
+			compatible = "fsl,mpc5200-psc-uart";
 			port-number = <1>;  // Logical port assignment
 			reg = <2200 100>;
 			interrupts = <2 2 0>;
@@ -126,7 +117,7 @@
 
 		serial@2400 {		// PSC3
 			device_type = "serial";
-			compatible = "mpc5200-psc-uart";
+			compatible = "fsl,mpc5200-psc-uart";
 			port-number = <2>;  // Logical port assignment
 			reg = <2400 100>;
 			interrupts = <2 3 0>;
@@ -135,22 +126,22 @@
 
 		ethernet@3000 {
 			device_type = "network";
-			compatible = "mpc5200-fec";
+			compatible = "fsl,mpc5200-fec";
 			reg = <3000 800>;
-			local-mac-address = [ 00 00 00 00 00 00 ]; /* Filled in by U-Boot */
+			local-mac-address = [ 00 00 00 00 00 00 ];
 			interrupts = <2 5 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
 		ata@3a00 {
-			compatible = "mpc5200-ata";
+			compatible = "fsl,mpc5200-ata";
 			reg = <3a00 100>;
 			interrupts = <2 7 0>;
 			interrupt-parent = <&mpc5200_pic>;
 		};
 
 		i2c@3d40 {
-			compatible = "mpc5200-i2c","fsl-i2c";
+			compatible = "fsl,mpc5200-i2c","fsl-i2c";
 			reg = <3d40 40>;
 			interrupts = <2 10 0>;
 			interrupt-parent = <&mpc5200_pic>;
@@ -158,7 +149,7 @@
 		};
 
 		sram@8000 {
-			compatible = "mpc5200-sram";
+			compatible = "fsl,mpc5200-sram";
 			reg = <8000 4000>;
 		};
 	};
diff --git a/arch/powerpc/boot/serial.c b/arch/powerpc/boot/serial.c
index b6c68ef..9960421 100644
--- a/arch/powerpc/boot/serial.c
+++ b/arch/powerpc/boot/serial.c
@@ -126,7 +126,7 @@
 	         dt_is_compatible(devp, "fsl,cpm2-scc-uart") ||
 	         dt_is_compatible(devp, "fsl,cpm2-smc-uart"))
 		rc = cpm_console_init(devp, &serial_cd);
-	else if (dt_is_compatible(devp, "mpc5200-psc-uart"))
+	else if (dt_is_compatible(devp, "fsl,mpc5200-psc-uart"))
 		rc = mpc5200_psc_console_init(devp, &serial_cd);
 	else if (dt_is_compatible(devp, "xlnx,opb-uartlite-1.00.b") ||
 		 dt_is_compatible(devp, "xlnx,xps-uartlite-1.00.a"))