Merge tag 'qcom-dt-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt
Qualcomm Device Tree Changes for v4.8
* Reverse BAM dma node reverts
* Add BAM remote control options for affected platforms
* Enable peripherals on APQ8074 dragonboard
* Enable PMA8084 pwrky
* Fix PMIC reg entries by removing unnecessary size element
* Add SCM binding and support for all currently supported boards
* Add Qualcomm WCNSS binding documentation
* Rename db600c to SD_600eval and add peripheral nodes
* Remove gpio key entry from Nexus7
* Add APQ8060 based dragonboard and associated peripherals
* Add ARMv7 PMU for IPQ4019
* Update smem state cells to match documentation
* tag 'qcom-dt-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux: (26 commits)
dts: ipq4019: support ARMv7 PMU
ARM: dts: add Qualcomm APQ8060-based Dragonboard
ARM: dts: move the fixed MMC regulator to SURF board
ARM: dts: fix the MSM8660 RTC base address
ARM: dts: add I2C block in GSBI12
ARM: dts: add L2CC and RPM with regulators for MSM8660
ARM: dts: add SDCC5 to Qualcomm MSM8660
ARM: dts: add GPIO and MPP to MSM8660 PMIC
device-tree: nexus7: Remove power gpio key entry and use pmic8xxx-pwrkey
arm: dts: qcom: Update smem state cells usage
ARM: dts: qcom: msm8974-honami: Set DMA as remotely controlled
ARM: dts: sd_600eval: Fix eMMC lockup issue
ARM: dts: apq8064: rename db600c to SD_600eval
ARM: dts: apq8064: move sdcc3 pinctrls out of baord file
ARM: dts: apq8064: move sdcc1 pinctrl nodes to soc file
dt: binding: Add Qualcomm WCNSS control binding
dts: qcom: apq8064: Add SCM firmware node
dts: qcom: msm8974: Add SCM firmware node
dts: qcom: apq8084: Add SCM firmware node
dt/bindings: firmware: Add Qualcomm SCM binding
...
Signed-off-by: Olof Johansson <olof@lixom.net>
diff --git a/Documentation/devicetree/bindings/firmware/qcom,scm.txt b/Documentation/devicetree/bindings/firmware/qcom,scm.txt
new file mode 100644
index 0000000..3b4436e
--- /dev/null
+++ b/Documentation/devicetree/bindings/firmware/qcom,scm.txt
@@ -0,0 +1,28 @@
+QCOM Secure Channel Manager (SCM)
+
+Qualcomm processors include an interface to communicate to the secure firmware.
+This interface allows for clients to request different types of actions. These
+can include CPU power up/down, HDCP requests, loading of firmware, and other
+assorted actions.
+
+Required properties:
+- compatible: must contain one of the following:
+ * "qcom,scm-apq8064" for APQ8064 platforms
+ * "qcom,scm-msm8660" for MSM8660 platforms
+ * "qcom,scm-msm8690" for MSM8690 platforms
+ * "qcom,scm" for later processors (MSM8916, APQ8084, MSM8974, etc)
+- clocks: One to three clocks may be required based on compatible.
+ * Only core clock required for "qcom,scm-apq8064", "qcom,scm-msm8660", and "qcom,scm-msm8960"
+ * Core, iface, and bus clocks required for "qcom,scm"
+- clock-names: Must contain "core" for the core clock, "iface" for the interface
+ clock and "bus" for the bus clock per the requirements of the compatible.
+
+Example for MSM8916:
+
+ firmware {
+ scm {
+ compatible = "qcom,scm";
+ clocks = <&gcc GCC_CRYPTO_CLK> , <&gcc GCC_CRYPTO_AXI_CLK>, <&gcc GCC_CRYPTO_AHB_CLK>;
+ clock-names = "core", "bus", "iface";
+ };
+ };
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,wcnss.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,wcnss.txt
new file mode 100644
index 0000000..4ea39e9
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,wcnss.txt
@@ -0,0 +1,116 @@
+Qualcomm WCNSS Binding
+
+This binding describes the Qualcomm WCNSS hardware. It consists of control
+block and a BT, WiFi and FM radio block, all using SMD as command channels.
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be: "qcom,wcnss",
+
+- qcom,smd-channel:
+ Usage: required
+ Value type: <string>
+ Definition: standard SMD property specifying the SMD channel used for
+ communication with the WiFi firmware.
+ Should be "WCNSS_CTRL".
+
+- qcom,mmio:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: reference to a node specifying the wcnss "ccu" and "dxe"
+ register blocks. The node must be compatible with one of
+ the following:
+ "qcom,riva",
+ "qcom,pronto"
+
+= SUBNODES
+The subnodes of the wcnss node are optional and describe the individual blocks in
+the WCNSS.
+
+== Bluetooth
+The following properties are defined to the bluetooth node:
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be:
+ "qcom,wcnss-bt"
+
+== WiFi
+The following properties are defined to the WiFi node:
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be one of:
+ "qcom,wcnss-wlan",
+
+- interrupts:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: should specify the "rx" and "tx" interrupts
+
+- interrupt-names:
+ Usage: required
+ Value type: <stringlist>
+ Definition: must contain "rx" and "tx"
+
+- qcom,smem-state:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: should reference the tx-enable and tx-rings-empty SMEM states
+
+- qcom,smem-state-names:
+ Usage: required
+ Value type: <stringlist>
+ Definition: must contain "tx-enable" and "tx-rings-empty"
+
+= EXAMPLE
+The following example represents a SMD node, with one edge representing the
+"pronto" subsystem, with the wcnss device and its wcn3680 BT and WiFi blocks
+described; as found on the 8974 platform.
+
+smd {
+ compatible = "qcom,smd";
+
+ pronto-edge {
+ interrupts = <0 142 1>;
+
+ qcom,ipc = <&apcs 8 17>;
+ qcom,smd-edge = <6>;
+
+ wcnss {
+ compatible = "qcom,wcnss";
+ qcom,smd-channels = "WCNSS_CTRL";
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ qcom,mmio = <&pronto>;
+
+ bt {
+ compatible = "qcom,wcnss-bt";
+ };
+
+ wlan {
+ compatible = "qcom,wcnss-wlan";
+
+ interrupts = <0 145 0>, <0 146 0>;
+ interrupt-names = "tx", "rx";
+
+ qcom,smem-state = <&apps_smsm 10>, <&apps_smsm 9>;
+ qcom,smem-state-names = "tx-enable", "tx-rings-empty";
+ };
+ };
+ };
+};
+
+soc {
+ pronto: pronto {
+ compatible = "qcom,pronto";
+
+ reg = <0xfb204000 0x2000>, <0xfb202000 0x1000>, <0xfb21b000 0x3000>;
+ reg-names = "ccu", "dxe", "pmu";
+ };
+};
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 6dfefa3..1739959 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -578,7 +578,8 @@
dtb-$(CONFIG_ARCH_OXNAS) += \
wd-mbwe.dtb
dtb-$(CONFIG_ARCH_QCOM) += \
- qcom-apq8064-arrow-db600c.dtb \
+ qcom-apq8060-dragonboard.dtb \
+ qcom-apq8064-arrow-sd-600eval.dtb \
qcom-apq8064-cm-qs600.dtb \
qcom-apq8064-ifc6410.dtb \
qcom-apq8064-sony-xperia-yuga.dtb \
diff --git a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
new file mode 100644
index 0000000..0abc93e
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
@@ -0,0 +1,626 @@
+/*
+ * Copyright 2016 Linaro Ltd
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
+ * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include "qcom-msm8660.dtsi"
+
+/ {
+ model = "Qualcomm APQ8060 Dragonboard";
+ compatible = "qcom,apq8060-dragonboard", "qcom,msm8660";
+
+ aliases {
+ serial0 = &gsbi12_serial;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ regulators {
+ compatible = "simple-bus";
+
+ /* Main power of the board: 3.7V */
+ vph: regulator-fixed {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+ regulator-name = "VPH";
+ regulator-type = "voltage";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ /* This is a levelshifter for SDCC5 */
+ dragon_vio_txb: txb0104rgyr {
+ compatible = "regulator-fixed";
+ regulator-name = "Dragon SDCC levelshifter";
+ vin-supply = <&pm8058_l14>;
+ regulator-always-on;
+ };
+ };
+
+ soc {
+ pinctrl@800000 {
+ /* eMMMC pins, all 8 data lines connected */
+ dragon_sdcc1_pins: sdcc1 {
+ mux {
+ pins = "gpio159", "gpio160", "gpio161",
+ "gpio162", "gpio163", "gpio164",
+ "gpio165", "gpio166", "gpio167",
+ "gpio168";
+ function = "sdc1";
+ };
+ clk {
+ pins = "gpio167"; /* SDC5 CLK */
+ drive-strength = <16>;
+ bias-disable;
+ };
+ cmd {
+ pins = "gpio168"; /* SDC5 CMD */
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+ data {
+ /* SDC5 D0 to D7 */
+ pins = "gpio159", "gpio160", "gpio161", "gpio162",
+ "gpio163", "gpio164", "gpio165", "gpio166";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+ };
+
+ /*
+ * The SDCC3 pins are hardcoded (non-muxable) but need some pin
+ * configuration.
+ */
+ dragon_sdcc3_pins: sdcc3 {
+ clk {
+ pins = "sdc3_clk";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ cmd {
+ pins = "sdc3_cmd";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ data {
+ pins = "sdc3_data";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+
+ /* Second SD card slot pins */
+ dragon_sdcc5_pins: sdcc5 {
+ mux {
+ pins = "gpio95", "gpio96", "gpio97",
+ "gpio98", "gpio99", "gpio100";
+ function = "sdc5";
+ };
+ clk {
+ pins = "gpio97"; /* SDC5 CLK */
+ drive-strength = <16>;
+ bias-disable;
+ };
+ cmd {
+ pins = "gpio95"; /* SDC5 CMD */
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+ data {
+ /* SDC5 D0 to D3 */
+ pins = "gpio96", "gpio98", "gpio99", "gpio100";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+ };
+
+ dragon_gsbi12_i2c_pins: gsbi12_i2c {
+ mux {
+ pins = "gpio115", "gpio116";
+ function = "gsbi12";
+ };
+ pinconf {
+ pins = "gpio115", "gpio116";
+ drive-strength = <16>;
+ /* These have external pull-up 4.7kOhm to 1.8V */
+ bias-disable;
+ };
+ };
+
+ /* Primary serial port uart 0 pins */
+ dragon_gsbi12_serial_pins: gsbi12_serial {
+ mux {
+ pins = "gpio117", "gpio118";
+ function = "gsbi12";
+ };
+ tx {
+ pins = "gpio117";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ rx {
+ pins = "gpio118";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+ };
+
+ qcom,ssbi@500000 {
+ pmic@0 {
+ keypad@148 {
+ linux,keymap = <
+ MATRIX_KEY(0, 0, KEY_MENU)
+ MATRIX_KEY(0, 2, KEY_1)
+ MATRIX_KEY(0, 3, KEY_4)
+ MATRIX_KEY(0, 4, KEY_7)
+ MATRIX_KEY(1, 0, KEY_UP)
+ MATRIX_KEY(1, 1, KEY_LEFT)
+ MATRIX_KEY(1, 2, KEY_DOWN)
+ MATRIX_KEY(1, 3, KEY_5)
+ MATRIX_KEY(1, 3, KEY_8)
+ MATRIX_KEY(2, 0, KEY_HOME)
+ MATRIX_KEY(2, 1, KEY_REPLY)
+ MATRIX_KEY(2, 2, KEY_2)
+ MATRIX_KEY(2, 3, KEY_6)
+ MATRIX_KEY(3, 0, KEY_VOLUMEUP)
+ MATRIX_KEY(3, 1, KEY_RIGHT)
+ MATRIX_KEY(3, 2, KEY_3)
+ MATRIX_KEY(3, 3, KEY_9)
+ MATRIX_KEY(3, 4, KEY_SWITCHVIDEOMODE)
+ MATRIX_KEY(4, 0, KEY_VOLUMEDOWN)
+ MATRIX_KEY(4, 1, KEY_BACK)
+ MATRIX_KEY(4, 2, KEY_CAMERA)
+ MATRIX_KEY(4, 3, KEY_KBDILLUMTOGGLE)
+ >;
+ keypad,num-rows = <6>;
+ keypad,num-columns = <5>;
+ };
+
+ gpio@150 {
+ dragon_bmp085_gpios: bmp085-gpios {
+ pinconf {
+ pins = "gpio16";
+ function = "normal";
+ input-enable;
+ bias-disable;
+ power-source = <PM8058_GPIO_S3>;
+ };
+ };
+ dragon_sdcc3_gpios: sdcc3-gpios {
+ pinconf {
+ pins = "gpio22";
+ function = "normal";
+ input-enable;
+ bias-disable;
+ power-source = <PM8058_GPIO_S3>;
+ };
+ };
+ dragon_sdcc5_gpios: sdcc5-gpios {
+ pinconf {
+ pins = "gpio26";
+ function = "normal";
+ input-enable;
+ bias-pull-up;
+ qcom,pull-up-strength = <PMIC_GPIO_PULL_UP_30>;
+ power-source = <PM8058_GPIO_S3>;
+ };
+ };
+ dragon_ak8975_gpios: ak8975-gpios {
+ pinconf {
+ pins = "gpio33";
+ function = "normal";
+ input-enable;
+ bias-disable;
+ power-source = <PM8058_GPIO_S3>;
+ };
+ };
+ };
+ };
+ };
+
+ gsbi@19c00000 {
+ status = "ok";
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+
+ serial@19c40000 {
+ status = "ok";
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_gsbi12_serial_pins>;
+ };
+
+ i2c@19c80000 {
+ status = "ok";
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_gsbi12_i2c_pins>;
+
+ ak8975@0c {
+ compatible = "asahi-kasei,ak8975";
+ reg = <0x0c>;
+ /* GPIO33 has interrupt 224 on the PM8058 */
+ interrupt-parent = <&pm8058_gpio>;
+ interrupts = <224 IRQ_TYPE_EDGE_RISING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_ak8975_gpios>;
+ vid-supply = <&pm8058_lvs0>; // 1.8V
+ vdd-supply = <&pm8058_l14>; // 2.85V
+ };
+ bmp085@77 {
+ compatible = "bosch,bmp085";
+ reg = <0x77>;
+ /* GPIO16 has interrupt 207 on the PM8058 */
+ interrupt-parent = <&pm8058_gpio>;
+ interrupts = <207 IRQ_TYPE_EDGE_RISING>;
+ reset-gpios = <&tlmm 86 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_bmp085_gpios>;
+ vddd-supply = <&pm8058_lvs0>; // 1.8V
+ vdda-supply = <&pm8058_l14>; // 2.85V
+ };
+ };
+ };
+
+ rpm@104000 {
+ /*
+ * Set up of the PMIC RPM regulators for this board
+ * PM8901 supplies "preliminary regulators" whatever
+ * that means
+ */
+ pm8901-regulators {
+ vdd_l0-supply = <&pm8901_s4>;
+ vdd_l1-supply = <&vph>;
+ vdd_l2-supply = <&vph>;
+ vdd_l3-supply = <&vph>;
+ vdd_l4-supply = <&vph>;
+ vdd_l5-supply = <&vph>;
+ vdd_l6-supply = <&vph>;
+ /* vdd_s0-supply, vdd_s1-supply: SAW regulators */
+ vdd_s2-supply = <&vph>;
+ vdd_s3-supply = <&vph>;
+ vdd_s4-supply = <&vph>;
+ lvs0_in-supply = <&pm8058_s3>;
+ lvs1_in-supply = <&pm8901_s4>;
+ lvs2_in-supply = <&pm8058_l0>;
+ lvs3_in-supply = <&pm8058_s2>;
+ mvs_in-supply = <&pm8058_s3>;
+
+ l0 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ };
+ l1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ bias-pull-down;
+ };
+ l2 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <3300000>;
+ bias-pull-down;
+ };
+ l3 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ bias-pull-down;
+ };
+ l4 {
+ regulator-min-microvolt = <2600000>;
+ regulator-max-microvolt = <2600000>;
+ bias-pull-down;
+ };
+ l5 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ bias-pull-down;
+ };
+ l6 {
+ regulator-min-microvolt = <2200000>;
+ regulator-max-microvolt = <2200000>;
+ bias-pull-down;
+ };
+
+ /* s0 and s1 are SAW regulators controlled over SPM */
+ s2 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ };
+ s3 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ };
+ s4 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ };
+
+ /* LVS0 thru 3 and mvs0 are just switches */
+ lvs0 {
+ regulator-always-on;
+ };
+ lvs1 { };
+ lvs2 { };
+ lvs3 { };
+ mvs0 {};
+
+ };
+
+ pm8058-regulators {
+ vdd_l0_l1_lvs-supply = <&pm8058_s3>;
+ vdd_l2_l11_l12-supply = <&vph>;
+ vdd_l3_l4_l5-supply = <&vph>;
+ vdd_l6_l7-supply = <&vph>;
+ vdd_l8-supply = <&vph>;
+ vdd_l9-supply = <&vph>;
+ vdd_l10-supply = <&vph>;
+ vdd_l13_l16-supply = <&pm8058_s4>;
+ vdd_l14_l15-supply = <&vph>;
+ vdd_l17_l18-supply = <&vph>;
+ vdd_l19_l20-supply = <&vph>;
+ vdd_l21-supply = <&pm8058_s3>;
+ vdd_l22-supply = <&pm8058_s3>;
+ vdd_l23_l24_l25-supply = <&pm8058_s3>;
+ vdd_s0-supply = <&vph>;
+ vdd_s1-supply = <&vph>;
+ vdd_s2-supply = <&vph>;
+ vdd_s3-supply = <&vph>;
+ vdd_s4-supply = <&vph>;
+ vdd_ncp-supply = <&vph>;
+
+ l0 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ };
+ l1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ };
+ l2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2600000>;
+ bias-pull-down;
+ };
+ l3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+ l4 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ bias-pull-down;
+ };
+ l5 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ bias-pull-down;
+ };
+ l6 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3600000>;
+ bias-pull-down;
+ };
+ l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+ l8 {
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <3050000>;
+ bias-pull-down;
+ };
+ l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+ l10 {
+ regulator-min-microvolt = <2600000>;
+ regulator-max-microvolt = <2600000>;
+ bias-pull-down;
+ };
+ l11 {
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ bias-pull-down;
+ };
+ l12 {
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ bias-pull-down;
+ };
+ l13 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ bias-pull-down;
+ };
+ l14 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+ l15 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ bias-pull-down;
+ };
+ l16 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ regulator-always-on;
+ };
+ l17 {
+ // 1.5V according to schematic
+ regulator-min-microvolt = <2600000>;
+ regulator-max-microvolt = <2600000>;
+ bias-pull-down;
+ };
+ l18 {
+ regulator-min-microvolt = <2200000>;
+ regulator-max-microvolt = <2200000>;
+ bias-pull-down;
+ };
+ l19 {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ bias-pull-down;
+ };
+ l20 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+ l21 {
+ // 1.1 V according to schematic
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ regulator-always-on;
+ };
+ l22 {
+ // 1.2 V according to schematic
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1150000>;
+ bias-pull-down;
+ };
+ l23 {
+ // Unused
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ };
+ l24 {
+ // Unused
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ };
+ l25 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ bias-pull-down;
+ };
+
+ s0 {
+ // regulator-min-microvolt = <500000>;
+ // regulator-max-microvolt = <1325000>;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ };
+ s1 {
+ // regulator-min-microvolt = <500000>;
+ // regulator-max-microvolt = <1250000>;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ };
+ s2 {
+ // 1.3 V according to schematic
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1400000>;
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+ };
+ s3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,switch-mode-frequency = <1600000>;
+ regulator-always-on;
+ bias-pull-down;
+ };
+ s4 {
+ regulator-min-microvolt = <2200000>;
+ regulator-max-microvolt = <2200000>;
+ qcom,switch-mode-frequency = <1600000>;
+ regulator-always-on;
+ bias-pull-down;
+ };
+
+ /* LVS0 and LVS1 are just switches */
+ lvs0 {
+ bias-pull-down;
+ };
+ lvs1 {
+ bias-pull-down;
+ };
+
+ ncp {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,switch-mode-frequency = <1600000>;
+ };
+ };
+ };
+ amba {
+ /* Internal 3.69 GiB eMMC */
+ sdcc@12400000 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_sdcc1_pins>;
+ vmmc-supply = <&pm8901_l5>;
+ vqmmc-supply = <&pm8901_lvs0>;
+ };
+
+ /* External micro SD card, directly connected, pulled up to 2.85 V */
+ sdcc@12180000 {
+ status = "okay";
+ /* Enable SSBI GPIO 22 as input, use for card detect */
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_sdcc3_pins>, <&dragon_sdcc3_gpios>;
+ cd-gpios = <&pm8058_gpio 22 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+ vmmc-supply = <&pm8058_l14>;
+ };
+
+ /*
+ * Second external micro SD card, using two TXB104RGYR levelshifters
+ * to lift from 1.8 V to 2.85 V
+ */
+ sdcc@12200000 {
+ status = "okay";
+ /* Enable SSBI GPIO 26 as input, use for card detect */
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_sdcc5_pins>, <&dragon_sdcc5_gpios>;
+ cd-gpios = <&pm8058_gpio 26 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&tlmm 106 GPIO_ACTIVE_HIGH>;
+ vmmc-supply = <&pm8058_l14>;
+ vqmmc-supply = <&dragon_vio_txb>;
+ };
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
similarity index 100%
rename from arch/arm/boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi
rename to arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
similarity index 95%
rename from arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts
rename to arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
index e01b27e..39ae2bc 100644
--- a/arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
@@ -1,10 +1,11 @@
#include "qcom-apq8064-v2.0.dtsi"
-#include "qcom-apq8064-arrow-db600c-pins.dtsi"
+#include "qcom-apq8064-arrow-sd-600eval-pins.dtsi"
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/qcom-rpm.h>
/ {
- model = "Arrow Electronics, APQ8064 DB600c";
- compatible = "arrow,db600c", "qcom,apq8064";
+ model = "Arrow Electronics, APQ8064 SD_600eval";
+ compatible = "arrow,sd_600eval", "qcom,apq8064";
aliases {
serial0 = &gsbi7_serial;
@@ -82,7 +83,8 @@
s4 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
- qcom,switch-mode-frequency = <3200000>;
+ qcom,switch-mode-frequency = <1600000>;
+ qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
bias-pull-down;
regulator-always-on;
};
diff --git a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
index 32fedfa..7b05f07 100644
--- a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
@@ -29,12 +29,6 @@
gpio-keys {
compatible = "gpio-keys";
- power {
- label = "Power";
- gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_POWER>;
- gpio-key,wakeup;
- };
volume_up {
label = "Volume Up";
gpios = <&pm8921_gpio 4 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/qcom-apq8064-pins.dtsi b/arch/arm/boot/dts/qcom-apq8064-pins.dtsi
index 4102a98..6b801e7 100644
--- a/arch/arm/boot/dts/qcom-apq8064-pins.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8064-pins.dtsi
@@ -7,6 +7,46 @@
};
};
+ sdcc1_pins: sdcc1-pin-active {
+ clk {
+ pins = "sdc1_clk";
+ drive-strengh = <16>;
+ bias-disable;
+ };
+
+ cmd {
+ pins = "sdc1_cmd";
+ drive-strengh = <10>;
+ bias-pull-up;
+ };
+
+ data {
+ pins = "sdc1_data";
+ drive-strengh = <10>;
+ bias-pull-up;
+ };
+ };
+
+ sdcc3_pins: sdcc3-pin-active {
+ clk {
+ pins = "sdc3_clk";
+ drive-strengh = <8>;
+ bias-disable;
+ };
+
+ cmd {
+ pins = "sdc3_cmd";
+ drive-strengh = <8>;
+ bias-pull-up;
+ };
+
+ data {
+ pins = "sdc3_data";
+ drive-strengh = <8>;
+ bias-pull-up;
+ };
+ };
+
ps_hold: ps_hold {
mux {
pins = "gpio78";
diff --git a/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts b/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts
index 06b3c76..ebd675c 100644
--- a/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts
@@ -70,45 +70,6 @@
};
};
- sdcc1_pin_a: sdcc1-pin-active {
- clk {
- pins = "sdc1_clk";
- drive-strengh = <16>;
- bias-disable;
- };
-
- cmd {
- pins = "sdc1_cmd";
- drive-strengh = <10>;
- bias-pull-up;
- };
-
- data {
- pins = "sdc1_data";
- drive-strengh = <10>;
- bias-pull-up;
- };
- };
-
- sdcc3_pin_a: sdcc3-pin-active {
- clk {
- pins = "sdc3_clk";
- drive-strengh = <8>;
- bias-disable;
- };
-
- cmd {
- pins = "sdc3_cmd";
- drive-strengh = <8>;
- bias-pull-up;
- };
-
- data {
- pins = "sdc3_data";
- drive-strengh = <8>;
- bias-pull-up;
- };
- };
sdcc3_cd_pin_a: sdcc3-cd-pin-active {
pins = "gpio26";
@@ -417,9 +378,6 @@
vmmc-supply = <&pm8921_l5>;
vqmmc-supply = <&pm8921_s4>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&sdcc1_pin_a>;
};
sdcc3: sdcc@12180000 {
@@ -429,7 +387,7 @@
cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
- pinctrl-0 = <&sdcc3_pin_a>, <&sdcc3_cd_pin_a>;
+ pinctrl-0 = <&sdcc3_pins>, <&sdcc3_cd_pin_a>;
};
};
};
diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi
index df96ccd..906bb81 100644
--- a/arch/arm/boot/dts/qcom-apq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8064.dtsi
@@ -177,7 +177,7 @@
apps_smsm: apps@0 {
reg = <0>;
- #qcom,state-cells = <1>;
+ #qcom,smem-state-cells = <1>;
};
modem_smsm: modem@1 {
@@ -213,6 +213,12 @@
};
};
+ firmware {
+ scm {
+ compatible = "qcom,scm-apq8064";
+ };
+ };
+
soc: soc {
#address-cells = <1>;
#size-cells = <1>;
@@ -853,6 +859,8 @@
sdcc1: sdcc@12400000 {
status = "disabled";
compatible = "arm,pl18x", "arm,primecell";
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdcc1_pins>;
arm,primecell-periphid = <0x00051180>;
reg = <0x12400000 0x2000>;
interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
index c0e2053..ad51df2 100644
--- a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
+++ b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
@@ -25,11 +25,23 @@
bus-width = <8>;
non-removable;
status = "ok";
+
+ vmmc-supply = <&pm8941_l20>;
+ vqmmc-supply = <&pm8941_s3>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc1_pin_a>;
};
sdhci@f98a4900 {
cd-gpios = <&msmgpio 62 0x1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
bus-width = <4>;
+ status = "ok";
+
+ vmmc-supply = <&pm8941_l21>;
+ vqmmc-supply = <&pm8941_l13>;
};
@@ -59,6 +71,42 @@
function = "blsp_spi8";
};
};
+
+ sdhc1_pin_a: sdhc1-pin-active {
+ clk {
+ pins = "sdc1_clk";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ cmd-data {
+ pins = "sdc1_cmd", "sdc1_data";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+ };
+
+ sdhc2_cd_pin_a: sdhc2-cd-pin-active {
+ pins = "gpio62";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ sdhc2_pin_a: sdhc2-pin-active {
+ clk {
+ pins = "sdc2_clk";
+ drive-strength = <10>;
+ bias-disable;
+ };
+
+ cmd-data {
+ pins = "sdc2_cmd", "sdc2_data";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+ };
};
i2c@f9967000 {
@@ -75,4 +123,203 @@
};
};
};
+
+ smd {
+ rpm {
+ rpm_requests {
+ pm8841-regulators {
+ s1 {
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <1050000>;
+ };
+
+ s2 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
+ };
+
+ s3 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
+ };
+
+ s4 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1050000>;
+ };
+ };
+
+ pm8941-regulators {
+ vdd_l1_l3-supply = <&pm8941_s1>;
+ vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+ vdd_l4_l11-supply = <&pm8941_s1>;
+ vdd_l5_l7-supply = <&pm8941_s2>;
+ vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+ vin_5vs-supply = <&pm8941_5v>;
+
+ s1 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ s2 {
+ regulator-min-microvolt = <2150000>;
+ regulator-max-microvolt = <2150000>;
+ regulator-boot-on;
+ };
+
+ s3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ l3 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ l4 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-boot-on;
+ };
+
+ l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-boot-on;
+ };
+
+ l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l9 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ l10 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ l11 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ };
+
+ l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ l13 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-boot-on;
+ };
+
+ l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ l15 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
+
+ l16 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ l17 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ l18 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ l19 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ l20 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-allow-set-load;
+ regulator-boot-on;
+ regulator-system-load = <200000>;
+ };
+
+ l21 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+
+ regulator-boot-on;
+ };
+
+ l22 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ l23 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ l24 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+
+ regulator-boot-on;
+ };
+ };
+ };
+ };
+ };
};
diff --git a/arch/arm/boot/dts/qcom-apq8084.dtsi b/arch/arm/boot/dts/qcom-apq8084.dtsi
index a33a09f..7c2df06 100644
--- a/arch/arm/boot/dts/qcom-apq8084.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8084.dtsi
@@ -86,6 +86,14 @@
};
};
+ firmware {
+ scm {
+ compatible = "qcom,scm";
+ clocks = <&gcc GCC_CE1_CLK> , <&gcc GCC_CE1_AXI_CLK>, <&gcc GCC_CE1_AHB_CLK>;
+ clock-names = "core", "bus", "iface";
+ };
+ };
+
cpu-pmu {
compatible = "qcom,krait-pmu";
interrupts = <1 7 0xf04>;
diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom-ipq4019.dtsi
index 5c08d19..a520ef5 100644
--- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi
@@ -84,6 +84,12 @@
};
};
+ pmu {
+ compatible = "arm,cortex-a7-pmu";
+ interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) |
+ IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
clocks {
sleep_clk: sleep_clk {
compatible = "fixed-clock";
diff --git a/arch/arm/boot/dts/qcom-msm8660-surf.dts b/arch/arm/boot/dts/qcom-msm8660-surf.dts
index b17f379..23de764 100644
--- a/arch/arm/boot/dts/qcom-msm8660-surf.dts
+++ b/arch/arm/boot/dts/qcom-msm8660-surf.dts
@@ -23,15 +23,26 @@
};
};
+ /* Temporary fixed regulator */
+ vsdcc_fixed: vsdcc-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "SDCC Power";
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ regulator-always-on;
+ };
+
amba {
/* eMMC */
sdcc1: sdcc@12400000 {
status = "okay";
+ vmmc-supply = <&vsdcc_fixed>;
};
/* External micro SD card */
sdcc3: sdcc@12180000 {
status = "okay";
+ vmmc-supply = <&vsdcc_fixed>;
};
};
};
diff --git a/arch/arm/boot/dts/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom-msm8660.dtsi
index cd21403..acbe71f 100644
--- a/arch/arm/boot/dts/qcom-msm8660.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8660.dtsi
@@ -122,11 +122,22 @@
compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
reg = <0x19c40000 0x1000>,
<0x19c00000 0x1000>;
- interrupts = <0 195 0x0>;
+ interrupts = <0 195 IRQ_TYPE_NONE>;
clocks = <&gcc GSBI12_UART_CLK>, <&gcc GSBI12_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
};
+
+ gsbi12_i2c: i2c@19c80000 {
+ compatible = "qcom,i2c-qup-v1.1.1";
+ reg = <0x19c80000 0x1000>;
+ interrupts = <0 196 IRQ_TYPE_NONE>;
+ clocks = <&gcc GSBI12_QUP_CLK>, <&gcc GSBI12_H_CLK>;
+ clock-names = "core", "iface";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
};
qcom,ssbi@500000 {
@@ -143,6 +154,44 @@
#address-cells = <1>;
#size-cells = <0>;
+ pm8058_gpio: gpio@150 {
+ compatible = "qcom,pm8058-gpio",
+ "qcom,ssbi-gpio";
+ reg = <0x150>;
+ interrupt-parent = <&pmicintc>;
+ interrupts = <192 1>, <193 1>, <194 1>,
+ <195 1>, <196 1>, <197 1>,
+ <198 1>, <199 1>, <200 1>,
+ <201 1>, <202 1>, <203 1>,
+ <204 1>, <205 1>, <206 1>,
+ <207 1>, <208 1>, <209 1>,
+ <210 1>, <211 1>, <212 1>,
+ <213 1>, <214 1>, <215 1>,
+ <216 1>, <217 1>, <218 1>,
+ <219 1>, <220 1>, <221 1>,
+ <222 1>, <223 1>, <224 1>,
+ <225 1>, <226 1>, <227 1>,
+ <228 1>, <229 1>, <230 1>,
+ <231 1>, <232 1>, <233 1>,
+ <234 1>, <235 1>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ };
+
+ pm8058_mpps: mpps@50 {
+ compatible = "qcom,pm8058-mpp",
+ "qcom,ssbi-mpp";
+ reg = <0x50>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&pmicintc>;
+ interrupts =
+ <128 1>, <129 1>, <130 1>, <131 1>,
+ <132 1>, <133 1>, <134 1>, <135 1>,
+ <136 1>, <137 1>, <138 1>, <139 1>;
+ };
+
pwrkey@1c {
compatible = "qcom,pm8058-pwrkey";
reg = <0x1c>;
@@ -162,11 +211,11 @@
row-hold = <91500>;
};
- rtc@11d {
+ rtc@1e8 {
compatible = "qcom,pm8058-rtc";
+ reg = <0x1e8>;
interrupt-parent = <&pmicintc>;
interrupts = <39 1>;
- reg = <0x11d>;
allow-set-time;
};
@@ -177,13 +226,93 @@
};
};
- /* Temporary fixed regulator */
- vsdcc_fixed: vsdcc-regulator {
- compatible = "regulator-fixed";
- regulator-name = "SDCC Power";
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <2700000>;
- regulator-always-on;
+ l2cc: clock-controller@2082000 {
+ compatible = "syscon";
+ reg = <0x02082000 0x1000>;
+ };
+
+ rpm: rpm@104000 {
+ compatible = "qcom,rpm-msm8660";
+ reg = <0x00104000 0x1000>;
+ qcom,ipc = <&l2cc 0x8 2>;
+
+ interrupts = <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "ack", "err", "wakeup";
+ clocks = <&gcc RPM_MSG_RAM_H_CLK>;
+ clock-names = "ram";
+
+ rpmcc: clock-controller {
+ compatible = "qcom,rpmcc-apq8660", "qcom,rpmcc";
+ #clock-cells = <1>;
+ };
+
+ pm8901-regulators {
+ compatible = "qcom,rpm-pm8901-regulators";
+
+ pm8901_l0: l0 {};
+ pm8901_l1: l1 {};
+ pm8901_l2: l2 {};
+ pm8901_l3: l3 {};
+ pm8901_l4: l4 {};
+ pm8901_l5: l5 {};
+ pm8901_l6: l6 {};
+
+ /* S0 and S1 Handled as SAW regulators by SPM */
+ pm8901_s2: s2 {};
+ pm8901_s3: s3 {};
+ pm8901_s4: s4 {};
+
+ pm8901_lvs0: lvs0 {};
+ pm8901_lvs1: lvs1 {};
+ pm8901_lvs2: lvs2 {};
+ pm8901_lvs3: lvs3 {};
+
+ pm8901_mvs: mvs {};
+ };
+
+ pm8058-regulators {
+ compatible = "qcom,rpm-pm8058-regulators";
+
+ pm8058_l0: l0 {};
+ pm8058_l1: l1 {};
+ pm8058_l2: l2 {};
+ pm8058_l3: l3 {};
+ pm8058_l4: l4 {};
+ pm8058_l5: l5 {};
+ pm8058_l6: l6 {};
+ pm8058_l7: l7 {};
+ pm8058_l8: l8 {};
+ pm8058_l9: l9 {};
+ pm8058_l10: l10 {};
+ pm8058_l11: l11 {};
+ pm8058_l12: l12 {};
+ pm8058_l13: l13 {};
+ pm8058_l14: l14 {};
+ pm8058_l15: l15 {};
+ pm8058_l16: l16 {};
+ pm8058_l17: l17 {};
+ pm8058_l18: l18 {};
+ pm8058_l19: l19 {};
+ pm8058_l20: l20 {};
+ pm8058_l21: l21 {};
+ pm8058_l22: l22 {};
+ pm8058_l23: l23 {};
+ pm8058_l24: l24 {};
+ pm8058_l25: l25 {};
+
+ pm8058_s0: s0 {};
+ pm8058_s1: s1 {};
+ pm8058_s2: s2 {};
+ pm8058_s3: s3 {};
+ pm8058_s4: s4 {};
+
+ pm8058_lvs0: lvs0 {};
+ pm8058_lvs1: lvs1 {};
+
+ pm8058_ncp: ncp {};
+ };
};
amba {
@@ -205,7 +334,6 @@
non-removable;
cap-sd-highspeed;
cap-mmc-highspeed;
- vmmc-supply = <&vsdcc_fixed>;
};
sdcc3: sdcc@12180000 {
@@ -222,7 +350,21 @@
cap-mmc-highspeed;
max-frequency = <48000000>;
no-1-8-v;
- vmmc-supply = <&vsdcc_fixed>;
+ };
+
+ sdcc5: sdcc@12200000 {
+ compatible = "arm,pl18x", "arm,primecell";
+ arm,primecell-periphid = <0x00051180>;
+ status = "disabled";
+ reg = <0x12200000 0x8000>;
+ interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "cmd_irq";
+ clocks = <&gcc SDC5_CLK>, <&gcc SDC5_H_CLK>;
+ clock-names = "mclk", "apb_pclk";
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ max-frequency = <48000000>;
};
};
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts
index a0398b6..3fb4dad 100644
--- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts
@@ -367,6 +367,10 @@
};
};
+
+ dma-controller@f9944000 {
+ qcom,controlled-remotely;
+ };
};
&spmi_bus {
diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
index 6f16426..561d4d1 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
@@ -1,6 +1,6 @@
/dts-v1/;
-#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,gcc-msm8974.h>
#include "skeleton.dtsi"
@@ -182,7 +182,7 @@
modem_smp2p_out: master-kernel {
qcom,entry-name = "master-kernel";
- #qcom,state-cells = <1>;
+ #qcom,smem-state-cells = <1>;
};
modem_smp2p_in: slave-kernel {
@@ -208,7 +208,7 @@
wcnss_smp2p_out: master-kernel {
qcom,entry-name = "master-kernel";
- #qcom,state-cells = <1>;
+ #qcom,smem-state-cells = <1>;
};
wcnss_smp2p_in: slave-kernel {
@@ -232,7 +232,7 @@
apps_smsm: apps@0 {
reg = <0>;
- #qcom,state-cells = <1>;
+ #qcom,smem-state-cells = <1>;
};
modem_smsm: modem@1 {
@@ -260,6 +260,14 @@
};
};
+ firmware {
+ scm {
+ compatible = "qcom,scm";
+ clocks = <&gcc GCC_CE1_CLK>, <&gcc GCC_CE1_AXI_CLK>, <&gcc GCC_CE1_AHB_CLK>;
+ clock-names = "core", "bus", "iface";
+ };
+ };
+
soc: soc {
#address-cells = <1>;
#size-cells = <1>;
@@ -501,6 +509,8 @@
clock-names = "core", "iface";
#address-cells = <1>;
#size-cells = <0>;
+ dmas = <&blsp2_dma 20>, <&blsp2_dma 21>;
+ dma-names = "tx", "rx";
};
spmi_bus: spmi@fc4cf000 {
@@ -518,6 +528,16 @@
interrupt-controller;
#interrupt-cells = <4>;
};
+
+ blsp2_dma: dma-controller@f9944000 {
+ compatible = "qcom,bam-v1.4.0";
+ reg = <0xf9944000 0x19000>;
+ interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP2_AHB_CLK>;
+ clock-names = "bam_clk";
+ #dma-cells = <1>;
+ qcom,ee = <0>;
+ };
};
smd {
diff --git a/arch/arm/boot/dts/qcom-pma8084.dtsi b/arch/arm/boot/dts/qcom-pma8084.dtsi
index 4e9bd3f..82d2580 100644
--- a/arch/arm/boot/dts/qcom-pma8084.dtsi
+++ b/arch/arm/boot/dts/qcom-pma8084.dtsi
@@ -12,15 +12,23 @@
rtc@6000 {
compatible = "qcom,pm8941-rtc";
- reg = <0x6000 0x100>,
- <0x6100 0x100>;
+ reg = <0x6000>,
+ <0x6100>;
reg-names = "rtc", "alarm";
interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
};
+ pwrkey@800 {
+ compatible = "qcom,pm8941-pwrkey";
+ reg = <0x800>;
+ interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
+ debounce = <15625>;
+ bias-pull-up;
+ };
+
pma8084_gpios: gpios@c000 {
compatible = "qcom,pma8084-gpio", "qcom,spmi-gpio";
- reg = <0xc000 0x1600>;
+ reg = <0xc000>;
gpio-controller;
#gpio-cells = <2>;
interrupts = <0 0xc0 0 IRQ_TYPE_NONE>,
@@ -49,7 +57,7 @@
pma8084_mpps: mpps@a000 {
compatible = "qcom,pma8084-mpp", "qcom,spmi-mpp";
- reg = <0xa000 0x800>;
+ reg = <0xa000>;
gpio-controller;
#gpio-cells = <2>;
interrupts = <0 0xa0 0 IRQ_TYPE_NONE>,
@@ -64,7 +72,7 @@
pma8084_temp: temp-alarm@2400 {
compatible = "qcom,spmi-temp-alarm";
- reg = <0x2400 0x100>;
+ reg = <0x2400>;
interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
#thermal-sensor-cells = <0>;
io-channels = <&pma8084_vadc VADC_DIE_TEMP>;
@@ -73,7 +81,7 @@
pma8084_vadc: vadc@3100 {
compatible = "qcom,spmi-vadc";
- reg = <0x3100 0x100>;
+ reg = <0x3100>;
interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
#address-cells = <1>;
#size-cells = <0>;