diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 5065842..45cb291 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -379,12 +379,6 @@
 	help
 	  SPI driver for CSR SiRFprimaII SoCs
 
-config SPI_STMP3XXX
-	tristate "Freescale STMP37xx/378x SPI/SSP controller"
-	depends on ARCH_STMP3XXX
-	help
-	  SPI driver for Freescale STMP37xx/378x SoC SSP interface
-
 config SPI_MXS
 	tristate "Freescale MXS SPI controller"
 	depends on ARCH_MXS
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index e0fca55..64e970b 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -60,7 +60,6 @@
 obj-$(CONFIG_SPI_SH_MSIOF)		+= spi-sh-msiof.o
 obj-$(CONFIG_SPI_SH_SCI)		+= spi-sh-sci.o
 obj-$(CONFIG_SPI_SIRF)		+= spi-sirf.o
-obj-$(CONFIG_SPI_STMP3XXX)		+= spi-stmp.o
 obj-$(CONFIG_SPI_TEGRA20_SFLASH)	+= spi-tegra20-sflash.o
 obj-$(CONFIG_SPI_TEGRA20_SLINK)		+= spi-tegra20-slink.o
 obj-$(CONFIG_SPI_TI_SSP)		+= spi-ti-ssp.o
diff --git a/drivers/spi/spi-stmp.c b/drivers/spi/spi-stmp.c
deleted file mode 100644
index 911e904..0000000
--- a/drivers/spi/spi-stmp.c
+++ /dev/null
@@ -1,664 +0,0 @@
-/*
- * Freescale STMP378X SPI master driver
- *
- * Author: dmitry pervushin <dimka@embeddedalley.com>
- *
- * Copyright 2008 Freescale Semiconductor, Inc. All Rights Reserved.
- * Copyright 2008 Embedded Alley Solutions, Inc All Rights Reserved.
- */
-
-/*
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/dma-mapping.h>
-#include <linux/delay.h>
-
-#include <mach/platform.h>
-#include <mach/stmp3xxx.h>
-#include <mach/dma.h>
-#include <mach/regs-ssp.h>
-#include <mach/regs-apbh.h>
-
-
-/* 0 means DMA mode(recommended, default), !0 - PIO mode */
-static int pio;
-static int clock;
-
-/* default timeout for busy waits is 2 seconds */
-#define STMP_SPI_TIMEOUT	(2 * HZ)
-
-struct stmp_spi {
-	int		id;
-
-	void *  __iomem regs;	/* vaddr of the control registers */
-
-	int		irq, err_irq;
-	u32		dma;
-	struct stmp3xxx_dma_descriptor d;
-
-	u32		speed_khz;
-	u32		saved_timings;
-	u32		divider;
-
-	struct clk	*clk;
-	struct device	*master_dev;
-
-	struct work_struct work;
-	struct workqueue_struct *workqueue;
-
-	/* lock protects queue access */
-	spinlock_t lock;
-	struct list_head queue;
-
-	struct completion done;
-};
-
-#define busy_wait(cond)							\
-	({								\
-	unsigned long end_jiffies = jiffies + STMP_SPI_TIMEOUT;		\
-	bool succeeded = false;						\
-	do {								\
-		if (cond) {						\
-			succeeded = true;				\
-			break;						\
-		}							\
-		cpu_relax();						\
-	} while (time_before(jiffies, end_jiffies));			\
-	succeeded;							\
-	})
-
-/**
- * stmp_spi_init_hw
- * Initialize the SSP port
- */
-static int stmp_spi_init_hw(struct stmp_spi *ss)
-{
-	int err = 0;
-	void *pins = ss->master_dev->platform_data;
-
-	err = stmp3xxx_request_pin_group(pins, dev_name(ss->master_dev));
-	if (err)
-		goto out;
-
-	ss->clk = clk_get(NULL, "ssp");
-	if (IS_ERR(ss->clk)) {
-		err = PTR_ERR(ss->clk);
-		goto out_free_pins;
-	}
-	clk_enable(ss->clk);
-
-	stmp3xxx_reset_block(ss->regs, false);
-	stmp3xxx_dma_reset_channel(ss->dma);
-
-	return 0;
-
-out_free_pins:
-	stmp3xxx_release_pin_group(pins, dev_name(ss->master_dev));
-out:
-	return err;
-}
-
-static void stmp_spi_release_hw(struct stmp_spi *ss)
-{
-	void *pins = ss->master_dev->platform_data;
-
-	if (ss->clk && !IS_ERR(ss->clk)) {
-		clk_disable(ss->clk);
-		clk_put(ss->clk);
-	}
-	stmp3xxx_release_pin_group(pins, dev_name(ss->master_dev));
-}
-
-static int stmp_spi_setup_transfer(struct spi_device *spi,
-		struct spi_transfer *t)
-{
-	u8 bits_per_word;
-	u32 hz;
-	struct stmp_spi *ss = spi_master_get_devdata(spi->master);
-	u16 rate;
-
-	bits_per_word = spi->bits_per_word;
-	if (t && t->bits_per_word)
-		bits_per_word = t->bits_per_word;
-
-	/*
-	 * Calculate speed:
-	 *	- by default, use maximum speed from ssp clk
-	 *	- if device overrides it, use it
-	 *	- if transfer specifies other speed, use transfer's one
-	 */
-	hz = 1000 * ss->speed_khz / ss->divider;
-	if (spi->max_speed_hz)
-		hz = min(hz, spi->max_speed_hz);
-	if (t && t->speed_hz)
-		hz = min(hz, t->speed_hz);
-
-	if (hz == 0) {
-		dev_err(&spi->dev, "Cannot continue with zero clock\n");
-		return -EINVAL;
-	}
-
-	if (bits_per_word != 8) {
-		dev_err(&spi->dev, "%s, unsupported bits_per_word=%d\n",
-			__func__, bits_per_word);
-		return -EINVAL;
-	}
-
-	dev_dbg(&spi->dev, "Requested clk rate = %uHz, max = %uHz/%d = %uHz\n",
-		hz, ss->speed_khz, ss->divider,
-		ss->speed_khz * 1000 / ss->divider);
-
-	if (ss->speed_khz * 1000 / ss->divider < hz) {
-		dev_err(&spi->dev, "%s, unsupported clock rate %uHz\n",
-			__func__, hz);
-		return -EINVAL;
-	}
-
-	rate = 1000 * ss->speed_khz/ss->divider/hz;
-
-	writel(BF(ss->divider, SSP_TIMING_CLOCK_DIVIDE)		|
-	       BF(rate - 1, SSP_TIMING_CLOCK_RATE),
-	       HW_SSP_TIMING + ss->regs);
-
-	writel(BF(1 /* mode SPI */, SSP_CTRL1_SSP_MODE)		|
-	       BF(4 /* 8 bits   */, SSP_CTRL1_WORD_LENGTH)	|
-	       ((spi->mode & SPI_CPOL) ? BM_SSP_CTRL1_POLARITY : 0) |
-	       ((spi->mode & SPI_CPHA) ? BM_SSP_CTRL1_PHASE : 0) |
-	       (pio ? 0 : BM_SSP_CTRL1_DMA_ENABLE),
-	       ss->regs + HW_SSP_CTRL1);
-
-	return 0;
-}
-
-static int stmp_spi_setup(struct spi_device *spi)
-{
-	/* spi_setup() does basic checks,
-	 * stmp_spi_setup_transfer() does more later
-	 */
-	if (spi->bits_per_word != 8) {
-		dev_err(&spi->dev, "%s, unsupported bits_per_word=%d\n",
-			__func__, spi->bits_per_word);
-		return -EINVAL;
-	}
-	return 0;
-}
-
-static inline u32 stmp_spi_cs(unsigned cs)
-{
-	return  ((cs & 1) ? BM_SSP_CTRL0_WAIT_FOR_CMD : 0) |
-		((cs & 2) ? BM_SSP_CTRL0_WAIT_FOR_IRQ : 0);
-}
-
-static int stmp_spi_txrx_dma(struct stmp_spi *ss, int cs,
-		unsigned char *buf, dma_addr_t dma_buf, int len,
-		int first, int last, bool write)
-{
-	u32 c0 = 0;
-	dma_addr_t spi_buf_dma = dma_buf;
-	int status = 0;
-	enum dma_data_direction dir = write ? DMA_TO_DEVICE : DMA_FROM_DEVICE;
-
-	c0 |= (first ? BM_SSP_CTRL0_LOCK_CS : 0);
-	c0 |= (last ? BM_SSP_CTRL0_IGNORE_CRC : 0);
-	c0 |= (write ? 0 : BM_SSP_CTRL0_READ);
-	c0 |= BM_SSP_CTRL0_DATA_XFER;
-
-	c0 |= stmp_spi_cs(cs);
-
-	c0 |= BF(len, SSP_CTRL0_XFER_COUNT);
-
-	if (!dma_buf)
-		spi_buf_dma = dma_map_single(ss->master_dev, buf, len, dir);
-
-	ss->d.command->cmd =
-		BF(len, APBH_CHn_CMD_XFER_COUNT)	|
-		BF(1, APBH_CHn_CMD_CMDWORDS)		|
-		BM_APBH_CHn_CMD_WAIT4ENDCMD		|
-		BM_APBH_CHn_CMD_IRQONCMPLT		|
-		BF(write ? BV_APBH_CHn_CMD_COMMAND__DMA_READ :
-			   BV_APBH_CHn_CMD_COMMAND__DMA_WRITE,
-		   APBH_CHn_CMD_COMMAND);
-	ss->d.command->pio_words[0] = c0;
-	ss->d.command->buf_ptr = spi_buf_dma;
-
-	stmp3xxx_dma_reset_channel(ss->dma);
-	stmp3xxx_dma_clear_interrupt(ss->dma);
-	stmp3xxx_dma_enable_interrupt(ss->dma);
-	init_completion(&ss->done);
-	stmp3xxx_dma_go(ss->dma, &ss->d, 1);
-	wait_for_completion(&ss->done);
-
-	if (!busy_wait(readl(ss->regs + HW_SSP_CTRL0) & BM_SSP_CTRL0_RUN))
-		status = -ETIMEDOUT;
-
-	if (!dma_buf)
-		dma_unmap_single(ss->master_dev, spi_buf_dma, len, dir);
-
-	return status;
-}
-
-static inline void stmp_spi_enable(struct stmp_spi *ss)
-{
-	stmp3xxx_setl(BM_SSP_CTRL0_LOCK_CS, ss->regs + HW_SSP_CTRL0);
-	stmp3xxx_clearl(BM_SSP_CTRL0_IGNORE_CRC, ss->regs + HW_SSP_CTRL0);
-}
-
-static inline void stmp_spi_disable(struct stmp_spi *ss)
-{
-	stmp3xxx_clearl(BM_SSP_CTRL0_LOCK_CS, ss->regs + HW_SSP_CTRL0);
-	stmp3xxx_setl(BM_SSP_CTRL0_IGNORE_CRC, ss->regs + HW_SSP_CTRL0);
-}
-
-static int stmp_spi_txrx_pio(struct stmp_spi *ss, int cs,
-		unsigned char *buf, int len,
-		bool first, bool last, bool write)
-{
-	if (first)
-		stmp_spi_enable(ss);
-
-	stmp3xxx_setl(stmp_spi_cs(cs), ss->regs + HW_SSP_CTRL0);
-
-	while (len--) {
-		if (last && len <= 0)
-			stmp_spi_disable(ss);
-
-		stmp3xxx_clearl(BM_SSP_CTRL0_XFER_COUNT,
-				ss->regs + HW_SSP_CTRL0);
-		stmp3xxx_setl(1, ss->regs + HW_SSP_CTRL0);
-
-		if (write)
-			stmp3xxx_clearl(BM_SSP_CTRL0_READ,
-					ss->regs + HW_SSP_CTRL0);
-		else
-			stmp3xxx_setl(BM_SSP_CTRL0_READ,
-					ss->regs + HW_SSP_CTRL0);
-
-		/* Run! */
-		stmp3xxx_setl(BM_SSP_CTRL0_RUN, ss->regs + HW_SSP_CTRL0);
-
-		if (!busy_wait(readl(ss->regs + HW_SSP_CTRL0) &
-				BM_SSP_CTRL0_RUN))
-			break;
-
-		if (write)
-			writel(*buf, ss->regs + HW_SSP_DATA);
-
-		/* Set TRANSFER */
-		stmp3xxx_setl(BM_SSP_CTRL0_DATA_XFER, ss->regs + HW_SSP_CTRL0);
-
-		if (!write) {
-			if (busy_wait((readl(ss->regs + HW_SSP_STATUS) &
-					BM_SSP_STATUS_FIFO_EMPTY)))
-				break;
-			*buf = readl(ss->regs + HW_SSP_DATA) & 0xFF;
-		}
-
-		if (!busy_wait(readl(ss->regs + HW_SSP_CTRL0) &
-					BM_SSP_CTRL0_RUN))
-			break;
-
-		/* advance to the next byte */
-		buf++;
-	}
-
-	return len < 0 ? 0 : -ETIMEDOUT;
-}
-
-static int stmp_spi_handle_message(struct stmp_spi *ss, struct spi_message *m)
-{
-	bool first, last;
-	struct spi_transfer *t, *tmp_t;
-	int status = 0;
-	int cs;
-
-	cs = m->spi->chip_select;
-
-	list_for_each_entry_safe(t, tmp_t, &m->transfers, transfer_list) {
-
-		first = (&t->transfer_list == m->transfers.next);
-		last = (&t->transfer_list == m->transfers.prev);
-
-		if (first || t->speed_hz || t->bits_per_word)
-			stmp_spi_setup_transfer(m->spi, t);
-
-		/* reject "not last" transfers which request to change cs */
-		if (t->cs_change && !last) {
-			dev_err(&m->spi->dev,
-				"Message with t->cs_change has been skipped\n");
-			continue;
-		}
-
-		if (t->tx_buf) {
-			status = pio ?
-			   stmp_spi_txrx_pio(ss, cs, (void *)t->tx_buf,
-				   t->len, first, last, true) :
-			   stmp_spi_txrx_dma(ss, cs, (void *)t->tx_buf,
-				   t->tx_dma, t->len, first, last, true);
-#ifdef DEBUG
-			if (t->len < 0x10)
-				print_hex_dump_bytes("Tx ",
-					DUMP_PREFIX_OFFSET,
-					t->tx_buf, t->len);
-			else
-				pr_debug("Tx: %d bytes\n", t->len);
-#endif
-		}
-		if (t->rx_buf) {
-			status = pio ?
-			   stmp_spi_txrx_pio(ss, cs, t->rx_buf,
-				   t->len, first, last, false) :
-			   stmp_spi_txrx_dma(ss, cs, t->rx_buf,
-				   t->rx_dma, t->len, first, last, false);
-#ifdef DEBUG
-			if (t->len < 0x10)
-				print_hex_dump_bytes("Rx ",
-					DUMP_PREFIX_OFFSET,
-					t->rx_buf, t->len);
-			else
-				pr_debug("Rx: %d bytes\n", t->len);
-#endif
-		}
-
-		if (t->delay_usecs)
-			udelay(t->delay_usecs);
-
-		if (status)
-			break;
-
-	}
-	return status;
-}
-
-/**
- * stmp_spi_handle - handle messages from the queue
- */
-static void stmp_spi_handle(struct work_struct *w)
-{
-	struct stmp_spi *ss = container_of(w, struct stmp_spi, work);
-	unsigned long flags;
-	struct spi_message *m;
-
-	spin_lock_irqsave(&ss->lock, flags);
-	while (!list_empty(&ss->queue)) {
-		m = list_entry(ss->queue.next, struct spi_message, queue);
-		list_del_init(&m->queue);
-		spin_unlock_irqrestore(&ss->lock, flags);
-
-		m->status = stmp_spi_handle_message(ss, m);
-		m->complete(m->context);
-
-		spin_lock_irqsave(&ss->lock, flags);
-	}
-	spin_unlock_irqrestore(&ss->lock, flags);
-
-	return;
-}
-
-/**
- * stmp_spi_transfer - perform message transfer.
- * Called indirectly from spi_async, queues all the messages to
- * spi_handle_message.
- * @spi: spi device
- * @m: message to be queued
- */
-static int stmp_spi_transfer(struct spi_device *spi, struct spi_message *m)
-{
-	struct stmp_spi *ss = spi_master_get_devdata(spi->master);
-	unsigned long flags;
-
-	m->status = -EINPROGRESS;
-	spin_lock_irqsave(&ss->lock, flags);
-	list_add_tail(&m->queue, &ss->queue);
-	queue_work(ss->workqueue, &ss->work);
-	spin_unlock_irqrestore(&ss->lock, flags);
-	return 0;
-}
-
-static irqreturn_t stmp_spi_irq(int irq, void *dev_id)
-{
-	struct stmp_spi *ss = dev_id;
-
-	stmp3xxx_dma_clear_interrupt(ss->dma);
-	complete(&ss->done);
-	return IRQ_HANDLED;
-}
-
-static irqreturn_t stmp_spi_irq_err(int irq, void *dev_id)
-{
-	struct stmp_spi *ss = dev_id;
-	u32 c1, st;
-
-	c1 = readl(ss->regs + HW_SSP_CTRL1);
-	st = readl(ss->regs + HW_SSP_STATUS);
-	dev_err(ss->master_dev, "%s: status = 0x%08X, c1 = 0x%08X\n",
-		__func__, st, c1);
-	stmp3xxx_clearl(c1 & 0xCCCC0000, ss->regs + HW_SSP_CTRL1);
-
-	return IRQ_HANDLED;
-}
-
-static int __devinit stmp_spi_probe(struct platform_device *dev)
-{
-	int err = 0;
-	struct spi_master *master;
-	struct stmp_spi *ss;
-	struct resource *r;
-
-	master = spi_alloc_master(&dev->dev, sizeof(struct stmp_spi));
-	if (master == NULL) {
-		err = -ENOMEM;
-		goto out0;
-	}
-	master->flags = SPI_MASTER_HALF_DUPLEX;
-
-	ss = spi_master_get_devdata(master);
-	platform_set_drvdata(dev, master);
-
-	/* Get resources(memory, IRQ) associated with the device */
-	r = platform_get_resource(dev, IORESOURCE_MEM, 0);
-	if (r == NULL) {
-		err = -ENODEV;
-		goto out_put_master;
-	}
-	ss->regs = ioremap(r->start, resource_size(r));
-	if (!ss->regs) {
-		err = -EINVAL;
-		goto out_put_master;
-	}
-
-	ss->master_dev = &dev->dev;
-	ss->id = dev->id;
-
-	INIT_WORK(&ss->work, stmp_spi_handle);
-	INIT_LIST_HEAD(&ss->queue);
-	spin_lock_init(&ss->lock);
-
-	ss->workqueue = create_singlethread_workqueue(dev_name(&dev->dev));
-	if (!ss->workqueue) {
-		err = -ENXIO;
-		goto out_put_master;
-	}
-	master->transfer = stmp_spi_transfer;
-	master->setup = stmp_spi_setup;
-
-	/* the spi->mode bits understood by this driver: */
-	master->mode_bits = SPI_CPOL | SPI_CPHA;
-
-	ss->irq = platform_get_irq(dev, 0);
-	if (ss->irq < 0) {
-		err = ss->irq;
-		goto out_put_master;
-	}
-	ss->err_irq = platform_get_irq(dev, 1);
-	if (ss->err_irq < 0) {
-		err = ss->err_irq;
-		goto out_put_master;
-	}
-
-	r = platform_get_resource(dev, IORESOURCE_DMA, 0);
-	if (r == NULL) {
-		err = -ENODEV;
-		goto out_put_master;
-	}
-
-	ss->dma = r->start;
-	err = stmp3xxx_dma_request(ss->dma, &dev->dev, dev_name(&dev->dev));
-	if (err)
-		goto out_put_master;
-
-	err = stmp3xxx_dma_allocate_command(ss->dma, &ss->d);
-	if (err)
-		goto out_free_dma;
-
-	master->bus_num = dev->id;
-	master->num_chipselect = 1;
-
-	/* SPI controller initializations */
-	err = stmp_spi_init_hw(ss);
-	if (err) {
-		dev_dbg(&dev->dev, "cannot initialize hardware\n");
-		goto out_free_dma_desc;
-	}
-
-	if (clock) {
-		dev_info(&dev->dev, "clock rate forced to %d\n", clock);
-		clk_set_rate(ss->clk, clock);
-	}
-	ss->speed_khz = clk_get_rate(ss->clk);
-	ss->divider = 2;
-	dev_info(&dev->dev, "max possible speed %d = %ld/%d kHz\n",
-		ss->speed_khz, clk_get_rate(ss->clk), ss->divider);
-
-	/* Register for SPI interrupt */
-	err = request_irq(ss->irq, stmp_spi_irq, 0,
-			  dev_name(&dev->dev), ss);
-	if (err) {
-		dev_dbg(&dev->dev, "request_irq failed, %d\n", err);
-		goto out_release_hw;
-	}
-
-	/* ..and shared interrupt for all SSP controllers */
-	err = request_irq(ss->err_irq, stmp_spi_irq_err, IRQF_SHARED,
-			  dev_name(&dev->dev), ss);
-	if (err) {
-		dev_dbg(&dev->dev, "request_irq(error) failed, %d\n", err);
-		goto out_free_irq;
-	}
-
-	err = spi_register_master(master);
-	if (err) {
-		dev_dbg(&dev->dev, "cannot register spi master, %d\n", err);
-		goto out_free_irq_2;
-	}
-	dev_info(&dev->dev, "at (mapped) 0x%08X, irq=%d, bus %d, %s mode\n",
-			(u32)ss->regs, ss->irq, master->bus_num,
-			pio ? "PIO" : "DMA");
-	return 0;
-
-out_free_irq_2:
-	free_irq(ss->err_irq, ss);
-out_free_irq:
-	free_irq(ss->irq, ss);
-out_free_dma_desc:
-	stmp3xxx_dma_free_command(ss->dma, &ss->d);
-out_free_dma:
-	stmp3xxx_dma_release(ss->dma);
-out_release_hw:
-	stmp_spi_release_hw(ss);
-out_put_master:
-	if (ss->workqueue)
-		destroy_workqueue(ss->workqueue);
-	if (ss->regs)
-		iounmap(ss->regs);
-	platform_set_drvdata(dev, NULL);
-	spi_master_put(master);
-out0:
-	return err;
-}
-
-static int __devexit stmp_spi_remove(struct platform_device *dev)
-{
-	struct stmp_spi *ss;
-	struct spi_master *master;
-
-	master = spi_master_get(platform_get_drvdata(dev));
-	ss = spi_master_get_devdata(master);
-
-	spi_unregister_master(master);
-
-	free_irq(ss->err_irq, ss);
-	free_irq(ss->irq, ss);
-	stmp3xxx_dma_free_command(ss->dma, &ss->d);
-	stmp3xxx_dma_release(ss->dma);
-	stmp_spi_release_hw(ss);
-	destroy_workqueue(ss->workqueue);
-	iounmap(ss->regs);
-	spi_master_put(master);
-	return 0;
-}
-
-#ifdef CONFIG_PM
-static int stmp_spi_suspend(struct platform_device *pdev, pm_message_t pmsg)
-{
-	struct stmp_spi *ss;
-	struct spi_master *master;
-
-	master = platform_get_drvdata(pdev);
-	ss = spi_master_get_devdata(master);
-
-	ss->saved_timings = readl(HW_SSP_TIMING + ss->regs);
-	clk_disable(ss->clk);
-
-	return 0;
-}
-
-static int stmp_spi_resume(struct platform_device *pdev)
-{
-	struct stmp_spi *ss;
-	struct spi_master *master;
-
-	master = platform_get_drvdata(pdev);
-	ss = spi_master_get_devdata(master);
-
-	clk_enable(ss->clk);
-	stmp3xxx_reset_block(ss->regs, false);
-	writel(ss->saved_timings, ss->regs + HW_SSP_TIMING);
-
-	return 0;
-}
-
-#else
-#define stmp_spi_suspend NULL
-#define stmp_spi_resume  NULL
-#endif
-
-static struct platform_driver stmp_spi_driver = {
-	.probe	= stmp_spi_probe,
-	.remove	= __devexit_p(stmp_spi_remove),
-	.driver = {
-		.name = "stmp3xxx_ssp",
-		.owner = THIS_MODULE,
-	},
-	.suspend = stmp_spi_suspend,
-	.resume  = stmp_spi_resume,
-};
-module_platform_driver(stmp_spi_driver);
-
-module_param(pio, int, S_IRUGO);
-module_param(clock, int, S_IRUGO);
-MODULE_AUTHOR("dmitry pervushin <dpervushin@embeddedalley.com>");
-MODULE_DESCRIPTION("STMP3xxx SPI/SSP driver");
-MODULE_LICENSE("GPL");