ide: add ide_set{_max}_pio() (take 4)
* Add IDE_HFLAG_ABUSE_{PREFETCH,FAST_DEVSEL,DMA_MODES} flags
and set them in ht6560, cmd640, cmd64x and sc1200 host drivers.
* Add set_pio_mode_abuse() for checking if host driver has a non-standard
->tuneproc() implementation and use it in do_special().
* Add ide_set_pio() for setting PIO mode (it uses hwif->pio_mask to find
the maximum PIO mode supported by the host), also add ide_set_max_pio()
wrapper for ide_set_pio() to use for auto-tuning. Convert users of
->tuneproc to use ide_set{_max}_pio() where possible. This leaves only
do_special(), set_using_pio(), ide_hwif_restore() and ide_set_pio() as
a direct users of ->tuneproc.
* Remove no longer needed ide_get_best_pio_mode() calls and printk-s
reporting PIO mode selected from ->tuneproc implementations.
* Rename ->tuneproc hook to ->set_pio_mode and make 'pio' argument const.
* Remove stale comment from ide_config_drive_speed().
v2:
* Fix "ata_" prefix (Noticed by Jeff).
v3:
* Minor cleanups/fixups per Sergei's suggestions.
v4:
* Fix compile problem in drivers/ide/pci/cmd640.c
(Noticed by Andrew Morton).
* Improve some ->set_pio_mode comments.
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
diff --git a/drivers/ide/pci/sc1200.c b/drivers/ide/pci/sc1200.c
index 059071c..f9f5ed9 100644
--- a/drivers/ide/pci/sc1200.c
+++ b/drivers/ide/pci/sc1200.c
@@ -272,19 +272,20 @@
}
/*
- * sc1200_tuneproc() handles selection/setting of PIO modes
+ * sc1200_set_pio_mode() handles setting of PIO modes
* for both the chipset and drive.
*
* All existing BIOSs for this chipset guarantee that all drives
* will have valid default PIO timings set up before we get here.
*/
-static void sc1200_tuneproc (ide_drive_t *drive, byte pio) /* mode=255 means "autotune" */
+
+static void sc1200_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
ide_hwif_t *hwif = HWIF(drive);
int mode = -1;
/*
- * bad abuse of ->tuneproc interface
+ * bad abuse of ->set_pio_mode interface
*/
switch (pio) {
case 200: mode = XFER_UDMA_0; break;
@@ -302,9 +303,6 @@
return;
}
- pio = ide_get_best_pio_mode(drive, pio, 4);
- printk("SC1200: %s: setting PIO mode%d\n", drive->name, pio);
-
if (sc1200_set_xfer_mode(drive, XFER_PIO_0 + pio) == 0)
sc1200_tunepio(drive, pio);
}
@@ -420,7 +418,8 @@
hwif->ide_dma_end = &sc1200_ide_dma_end;
if (!noautodma)
hwif->autodma = 1;
- hwif->tuneproc = &sc1200_tuneproc;
+
+ hwif->set_pio_mode = &sc1200_set_pio_mode;
hwif->speedproc = &sc1200_tune_chipset;
}
hwif->atapi_dma = 1;
@@ -436,6 +435,7 @@
.init_hwif = init_hwif_sc1200,
.autodma = AUTODMA,
.bootable = ON_BOARD,
+ .host_flags = IDE_HFLAG_ABUSE_DMA_MODES,
.pio_mask = ATA_PIO4,
};