Merge branch 'omap-for-v4.6/dt-gpmc' into omap-for-v4.6/dt
diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
index a2bd593..739bc48 100644
--- a/Documentation/devicetree/bindings/arm/omap/omap.txt
+++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
@@ -154,7 +154,7 @@
compatible = "compulab,am437x-sbc-t43", "compulab,am437x-cm-t43", "ti,am4372", "ti,am43"
- AM43x EPOS EVM
- compatible = "ti,am43x-epos-evm", "ti,am4372", "ti,am43"
+ compatible = "ti,am43x-epos-evm", "ti,am43", "ti,am438x"
- AM437x GP EVM
compatible = "ti,am437x-gp-evm", "ti,am4372", "ti,am43"
diff --git a/arch/arm/boot/dts/am335x-cm-t335.dts b/arch/arm/boot/dts/am335x-cm-t335.dts
index 7e77ce1..e835644 100644
--- a/arch/arm/boot/dts/am335x-cm-t335.dts
+++ b/arch/arm/boot/dts/am335x-cm-t335.dts
@@ -41,12 +41,51 @@
regulator-max-microvolt = <3300000>;
};
+ /* Regulator for WiFi */
+ vwlan_fixed: fixedregulator@2 {
+ compatible = "regulator-fixed";
+ regulator-name = "vwlan_fixed";
+ gpio = <&gpio0 20 GPIO_ACTIVE_HIGH>; /* gpio0_20 */
+ enable-active-high;
+ regulator-boot-off;
+ };
+
backlight {
compatible = "pwm-backlight";
pwms = <&ecap0 0 50000 0>;
brightness-levels = <0 51 53 56 62 75 101 152 255>;
default-brightness-level = <8>;
};
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "cm-t335";
+
+ simple-audio-card,widgets =
+ "Microphone", "Mic Jack",
+ "Line", "Line In",
+ "Headphone", "Headphone Jack";
+
+ simple-audio-card,routing =
+ "Headphone Jack", "LHPOUT",
+ "Headphone Jack", "RHPOUT",
+ "LLINEIN", "Line In",
+ "RLINEIN", "Line In",
+ "MICIN", "Mic Jack";
+
+ simple-audio-card,format = "i2s";
+ simple-audio-card,bitclock-master = <&sound_master>;
+ simple-audio-card,frame-master = <&sound_master>;
+
+ simple-audio-card,cpu {
+ sound-dai = <&mcasp1>;
+ };
+
+ sound_master: simple-audio-card,codec {
+ sound-dai = <&tlv320aic23>;
+ system-clock-frequency = <12000000>;
+ };
+ };
};
&am33xx_pinmux {
@@ -135,6 +174,24 @@
>;
};
+ dcan0_pins: pinmux_dcan0_pins {
+ pinctrl-single,pins = <
+ /* uart1_ctsn.dcan0_tx */
+ AM33XX_IOPAD(0x978, PIN_OUTPUT | MUX_MODE2)
+ /* uart1_rtsn.dcan0_rx */
+ AM33XX_IOPAD(0x97C, PIN_INPUT | MUX_MODE2)
+ >;
+ };
+
+ dcan1_pins: pinmux_dcan1_pins {
+ pinctrl-single,pins = <
+ /* uart1_rxd.dcan1_tx */
+ AM33XX_IOPAD(0x980, PIN_OUTPUT | MUX_MODE2)
+ /* uart1_txd.dcan1_rx */
+ AM33XX_IOPAD(0x984, PIN_INPUT | MUX_MODE2)
+ >;
+ };
+
ecap0_pins: pinmux_ecap0_pins {
pinctrl-single,pins = <
/* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */
@@ -224,6 +281,21 @@
>;
};
+ spi0_pins: pinmux_spi0_pins {
+ pinctrl-single,pins = <
+ /* spi0_sclk.spi0_sclk */
+ AM33XX_IOPAD(0x950, PIN_INPUT | MUX_MODE0)
+ /* spi0_d0.spi0_d0 */
+ AM33XX_IOPAD(0x954, PIN_OUTPUT_PULLUP | MUX_MODE0)
+ /* spi0_d1.spi0_d1 */
+ AM33XX_IOPAD(0x958, PIN_INPUT | MUX_MODE0)
+ /* spi0_cs0.spi0_cs0 */
+ AM33XX_IOPAD(0x95C, PIN_OUTPUT | MUX_MODE0)
+ /* spi0_cs1.spi0_cs1 */
+ AM33XX_IOPAD(0x960, PIN_OUTPUT | MUX_MODE0)
+ >;
+ };
+
/* wl1271 bluetooth */
bluetooth_pins: pinmux_bluetooth_pins {
pinctrl-single,pins = <
@@ -231,6 +303,30 @@
AM33XX_IOPAD(0x9b0, PIN_OUTPUT_PULLUP | MUX_MODE7)
>;
};
+
+ /* TLV320AIC23B codec */
+ mcasp1_pins: pinmux_mcasp1_pins {
+ pinctrl-single,pins = <
+ /* MII1_CRS.mcasp1_aclkx */
+ AM33XX_IOPAD(0x90c, PIN_INPUT_PULLDOWN | MUX_MODE4)
+ /* MII1_RX_ER.mcasp1_fsx */
+ AM33XX_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE4)
+ /* MII1_COL.mcasp1_axr2 */
+ AM33XX_IOPAD(0x908, PIN_INPUT_PULLDOWN | MUX_MODE4)
+ /* RMII1_REF_CLK.mcasp1_axr3 */
+ AM33XX_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE4)
+ >;
+ };
+
+ /* wl1271 WiFi */
+ wifi_pins: pinmux_wifi_pins {
+ pinctrl-single,pins = <
+ /* EMU1.gpio3_8 - WiFi IRQ */
+ AM33XX_IOPAD(0x9e8, PIN_INPUT_PULLUP | MUX_MODE7)
+ /* XDMA_EVENT_INTR1.gpio0_20 - WiFi enable */
+ AM33XX_IOPAD(0x9b4, PIN_OUTPUT | MUX_MODE7)
+ >;
+ };
};
&uart0 {
@@ -265,6 +361,13 @@
compatible = "emmicro,em3027";
reg = <0x56>;
};
+ /* Audio codec */
+ tlv320aic23: codec@1a {
+ compatible = "ti,tlv320aic23";
+ reg = <0x1a>;
+ #sound-dai-cells= <0>;
+ status = "okay";
+ };
};
&usb {
@@ -396,3 +499,70 @@
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
};
+
+&dcan0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&dcan0_pins>;
+};
+
+&dcan1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&dcan1_pins>;
+};
+
+/* Touschscreen and analog digital converter */
+&tscadc {
+ status = "okay";
+ tsc {
+ ti,wires = <4>;
+ ti,x-plate-resistance = <200>;
+ ti,coordinate-readouts = <5>;
+ ti,wire-config = <0x01 0x10 0x23 0x32>;
+ ti,charge-delay = <0x400>;
+ };
+
+ adc {
+ ti,adc-channels = <4 5 6 7>;
+ };
+};
+
+/* CPU audio */
+&mcasp1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcasp1_pins>;
+
+ op-mode = <0>; /* MCASP_IIS_MODE */
+ tdm-slots = <2>;
+ /* 16 serializers */
+ num-serializer = <16>;
+ serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
+ 0 0 2 1 0 0 0 0 0 0 0 0 0 0 0 0
+ >;
+ tx-num-evt = <1>;
+ rx-num-evt = <1>;
+
+ #sound-dai-cells= <0>;
+ status = "okay";
+};
+
+&spi0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins>;
+ ti,pindir-d0-out-d1-in = <1>;
+ /* WLS1271 WiFi */
+ wlcore: wlcore@1 {
+ compatible = "ti,wl1271";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_pins>;
+ reg = <1>;
+ spi-max-frequency = <48000000>;
+ clock-xtal;
+ ref-clock-frequency = <38400000>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+ vwlan-supply = <&vwlan_fixed>;
+ };
+};
diff --git a/arch/arm/boot/dts/am335x-sl50.dts b/arch/arm/boot/dts/am335x-sl50.dts
index d38edfa..a676869 100644
--- a/arch/arm/boot/dts/am335x-sl50.dts
+++ b/arch/arm/boot/dts/am335x-sl50.dts
@@ -19,6 +19,10 @@
};
};
+ chosen {
+ stdout-path = &uart0;
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
@@ -63,12 +67,28 @@
default-brightness-level = <6>;
};
+ clocks {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* audio external oscillator */
+ tlv320aic3x_mclk: oscillator@0 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24576000>; /* 24.576MHz */
+ };
+ };
+
sound {
compatible = "ti,da830-evm-audio";
ti,model = "AM335x-SL50";
ti,audio-codec = <&audio_codec>;
ti,mcasp-controller = <&mcasp0>;
- ti,codec-clock-rate = <12000000>;
+
+ clocks = <&tlv320aic3x_mclk>;
+ clock-names = "mclk";
+
ti,audio-routing =
"Headphone Jack", "HPLOUT",
"Headphone Jack", "HPROUT",
@@ -226,7 +246,7 @@
AM33XX_IOPAD(0x994, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp0_fsx.mcasp0_fsx */
AM33XX_IOPAD(0x990, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp0_aclkx.mcasp0_aclkx */
AM33XX_IOPAD(0x998, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp0_axr0.mcasp0_axr0 */
- AM33XX_IOPAD(0x99c, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mcasp0_ahclkr.mcasp0_axr2*/
+ AM33XX_IOPAD(0x99c, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mcasp0_ahclkr.mcasp0_axr2 */
>;
};
diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi
index 7957bd4..3993777 100644
--- a/arch/arm/boot/dts/am4372.dtsi
+++ b/arch/arm/boot/dts/am4372.dtsi
@@ -898,18 +898,6 @@
status = "disabled";
};
- am43xx_control_usb2phy1: control-phy@44e10620 {
- compatible = "ti,control-phy-usb2-am437";
- reg = <0x44e10620 0x4>;
- reg-names = "power";
- };
-
- am43xx_control_usb2phy2: control-phy@0x44e10628 {
- compatible = "ti,control-phy-usb2-am437";
- reg = <0x44e10628 0x4>;
- reg-names = "power";
- };
-
ocp2scp0: ocp2scp@483a8000 {
compatible = "ti,am437x-ocp2scp", "ti,omap-ocp2scp";
#address-cells = <1>;
@@ -920,7 +908,7 @@
usb2_phy1: phy@483a8000 {
compatible = "ti,am437x-usb2";
reg = <0x483a8000 0x8000>;
- ctrl-module = <&am43xx_control_usb2phy1>;
+ syscon-phy-power = <&scm_conf 0x620>;
clocks = <&usb_phy0_always_on_clk32k>,
<&usb_otg_ss0_refclk960m>;
clock-names = "wkupclk", "refclk";
@@ -939,7 +927,7 @@
usb2_phy2: phy@483e8000 {
compatible = "ti,am437x-usb2";
reg = <0x483e8000 0x8000>;
- ctrl-module = <&am43xx_control_usb2phy2>;
+ syscon-phy-power = <&scm_conf 0x628>;
clocks = <&usb_phy1_always_on_clk32k>,
<&usb_otg_ss1_refclk960m>;
clock-names = "wkupclk", "refclk";
diff --git a/arch/arm/boot/dts/am43x-epos-evm.dts b/arch/arm/boot/dts/am43x-epos-evm.dts
index b1f2bd6..948fb29 100644
--- a/arch/arm/boot/dts/am43x-epos-evm.dts
+++ b/arch/arm/boot/dts/am43x-epos-evm.dts
@@ -18,7 +18,7 @@
/ {
model = "TI AM43x EPOS EVM";
- compatible = "ti,am43x-epos-evm","ti,am4372","ti,am43";
+ compatible = "ti,am43x-epos-evm","ti,am438x","ti,am43";
aliases {
display0 = &lcd0;
diff --git a/arch/arm/boot/dts/am57xx-beagle-x15.dts b/arch/arm/boot/dts/am57xx-beagle-x15.dts
index 36c0fa6..50312f8 100644
--- a/arch/arm/boot/dts/am57xx-beagle-x15.dts
+++ b/arch/arm/boot/dts/am57xx-beagle-x15.dts
@@ -591,6 +591,11 @@
DRVDD-supply = <&vdd_3v3>;
DVDD-supply = <&aic_dvdd>;
};
+
+ eeprom: eeprom@50 {
+ compatible = "at,24c32";
+ reg = <0x50>;
+ };
};
&i2c3 {
diff --git a/arch/arm/boot/dts/dm8148-evm.dts b/arch/arm/boot/dts/dm8148-evm.dts
index e070862..862977f 100644
--- a/arch/arm/boot/dts/dm8148-evm.dts
+++ b/arch/arm/boot/dts/dm8148-evm.dts
@@ -35,6 +35,62 @@
phy-mode = "rgmii";
};
+&gpmc {
+ ranges = <0 0 0x04000000 0x01000000>; /* CS0: 16MB for NAND */
+
+ nand@0,0 {
+ linux,mtd-name= "micron,mt29f2g16aadwp";
+ reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ti,nand-ecc-opt = "bch8";
+ nand-bus-width = <16>;
+ gpmc,device-width = <2>;
+ gpmc,sync-clk-ps = <0>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <44>;
+ gpmc,cs-wr-off-ns = <44>;
+ gpmc,adv-on-ns = <6>;
+ gpmc,adv-rd-off-ns = <34>;
+ gpmc,adv-wr-off-ns = <44>;
+ gpmc,we-on-ns = <0>;
+ gpmc,we-off-ns = <40>;
+ gpmc,oe-on-ns = <0>;
+ gpmc,oe-off-ns = <54>;
+ gpmc,access-ns = <64>;
+ gpmc,rd-cycle-ns = <82>;
+ gpmc,wr-cycle-ns = <82>;
+ gpmc,wait-on-read = "true";
+ gpmc,wait-on-write = "true";
+ gpmc,bus-turnaround-ns = <0>;
+ gpmc,cycle2cycle-delay-ns = <0>;
+ gpmc,clk-activation-ns = <0>;
+ gpmc,wait-monitoring-ns = <0>;
+ gpmc,wr-access-ns = <40>;
+ gpmc,wr-data-mux-bus-ns = <0>;
+ partition@0 {
+ label = "X-Loader";
+ reg = <0 0x80000>;
+ };
+ partition@0x80000 {
+ label = "U-Boot";
+ reg = <0x80000 0x1c0000>;
+ };
+ partition@0x1c0000 {
+ label = "Environment";
+ reg = <0x240000 0x40000>;
+ };
+ partition@0x280000 {
+ label = "Kernel";
+ reg = <0x280000 0x500000>;
+ };
+ partition@0x780000 {
+ label = "Filesystem";
+ reg = <0x780000 0xf880000>;
+ };
+ };
+};
+
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&sd1_pins>;
diff --git a/arch/arm/boot/dts/dm814x-clocks.dtsi b/arch/arm/boot/dts/dm814x-clocks.dtsi
index 2600158..e0ea6a9 100644
--- a/arch/arm/boot/dts/dm814x-clocks.dtsi
+++ b/arch/arm/boot/dts/dm814x-clocks.dtsi
@@ -41,11 +41,11 @@
reg = <0x0040>;
};
- /* Optional auxosc, 20 - 30 MHz range, assume 27 MHz by default */
+ /* Optional auxosc, 20 - 30 MHz range, assume 22.5729 MHz by default */
auxosc_ck: auxosc_ck {
#clock-cells = <0>;
compatible = "fixed-clock";
- clock-frequency = <27000000>;
+ clock-frequency = <22572900>;
};
/* Optional 32768Hz crystal or clock on RTCOSC pins */
diff --git a/arch/arm/boot/dts/dm814x.dtsi b/arch/arm/boot/dts/dm814x.dtsi
index a25cd51..3fe68b1 100644
--- a/arch/arm/boot/dts/dm814x.dtsi
+++ b/arch/arm/boot/dts/dm814x.dtsi
@@ -548,6 +548,18 @@
reg-names = "gmii-sel";
};
};
+
+ gpmc: gpmc@50000000 {
+ compatible = "ti,am3352-gpmc";
+ ti,hwmods = "gpmc";
+ ti,no-idle-on-init;
+ reg = <0x50000000 0x2000>;
+ interrupts = <100>;
+ gpmc,num-cs = <7>;
+ gpmc,num-waitpins = <2>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ };
};
};
diff --git a/arch/arm/boot/dts/dra62x-j5eco-evm.dts b/arch/arm/boot/dts/dra62x-j5eco-evm.dts
index 7900806..3937a58 100644
--- a/arch/arm/boot/dts/dra62x-j5eco-evm.dts
+++ b/arch/arm/boot/dts/dra62x-j5eco-evm.dts
@@ -35,6 +35,62 @@
phy-mode = "rgmii";
};
+&gpmc {
+ ranges = <0 0 0x04000000 0x01000000>; /* CS0: 16MB for NAND */
+
+ nand@0,0 {
+ linux,mtd-name= "micron,mt29f2g16aadwp";
+ reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ti,nand-ecc-opt = "bch8";
+ nand-bus-width = <16>;
+ gpmc,device-width = <2>;
+ gpmc,sync-clk-ps = <0>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <44>;
+ gpmc,cs-wr-off-ns = <44>;
+ gpmc,adv-on-ns = <6>;
+ gpmc,adv-rd-off-ns = <34>;
+ gpmc,adv-wr-off-ns = <44>;
+ gpmc,we-on-ns = <0>;
+ gpmc,we-off-ns = <40>;
+ gpmc,oe-on-ns = <0>;
+ gpmc,oe-off-ns = <54>;
+ gpmc,access-ns = <64>;
+ gpmc,rd-cycle-ns = <82>;
+ gpmc,wr-cycle-ns = <82>;
+ gpmc,wait-on-read = "true";
+ gpmc,wait-on-write = "true";
+ gpmc,bus-turnaround-ns = <0>;
+ gpmc,cycle2cycle-delay-ns = <0>;
+ gpmc,clk-activation-ns = <0>;
+ gpmc,wait-monitoring-ns = <0>;
+ gpmc,wr-access-ns = <40>;
+ gpmc,wr-data-mux-bus-ns = <0>;
+ partition@0 {
+ label = "X-Loader";
+ reg = <0 0x80000>;
+ };
+ partition@0x80000 {
+ label = "U-Boot";
+ reg = <0x80000 0x1c0000>;
+ };
+ partition@0x1c0000 {
+ label = "Environment";
+ reg = <0x240000 0x40000>;
+ };
+ partition@0x280000 {
+ label = "Kernel";
+ reg = <0x280000 0x500000>;
+ };
+ partition@0x780000 {
+ label = "Filesystem";
+ reg = <0x780000 0xf880000>;
+ };
+ };
+};
+
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&sd1_pins>;
diff --git a/arch/arm/boot/dts/dra7-dspeve-thermal.dtsi b/arch/arm/boot/dts/dra7-dspeve-thermal.dtsi
new file mode 100644
index 0000000..1c39a84
--- /dev/null
+++ b/arch/arm/boot/dts/dra7-dspeve-thermal.dtsi
@@ -0,0 +1,27 @@
+/*
+ * Device Tree Source for DRA7x SoC DSPEVE thermal
+ *
+ * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <dt-bindings/thermal/thermal.h>
+
+dspeve_thermal: dspeve_thermal {
+ polling-delay-passive = <250>; /* milliseconds */
+ polling-delay = <500>; /* milliseconds */
+
+ /* sensor ID */
+ thermal-sensors = <&bandgap 3>;
+
+ trips {
+ dspeve_crit: dspeve_crit {
+ temperature = <125000>; /* milliCelsius */
+ hysteresis = <2000>; /* milliCelsius */
+ type = "critical";
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/dra7-iva-thermal.dtsi b/arch/arm/boot/dts/dra7-iva-thermal.dtsi
new file mode 100644
index 0000000..dd74a53
--- /dev/null
+++ b/arch/arm/boot/dts/dra7-iva-thermal.dtsi
@@ -0,0 +1,27 @@
+/*
+ * Device Tree Source for DRA7x SoC IVA thermal
+ *
+ * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <dt-bindings/thermal/thermal.h>
+
+iva_thermal: iva_thermal {
+ polling-delay-passive = <250>; /* milliseconds */
+ polling-delay = <500>; /* milliseconds */
+
+ /* sensor ID */
+ thermal-sensors = <&bandgap 4>;
+
+ trips {
+ iva_crit: iva_crit {
+ temperature = <125000>; /* milliCelsius */
+ hysteresis = <2000>; /* milliCelsius */
+ type = "critical";
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index 51ddc98..54f9cd8 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -156,6 +156,11 @@
compatible = "syscon";
reg = <0x1c04 0x0020>;
};
+
+ scm_conf_pcie: scm_conf@1c24 {
+ compatible = "syscon";
+ reg = <0x1c24 0x0024>;
+ };
};
cm_core_aon: cm_core_aon@5000 {
@@ -1168,14 +1173,6 @@
status = "disabled";
};
- omap_control_sata: control-phy@4a002374 {
- compatible = "ti,control-phy-pipe3";
- reg = <0x4a002374 0x4>;
- reg-names = "power";
- clocks = <&sys_clkin1>;
- clock-names = "sysclk";
- };
-
/* OCP2SCP3 */
ocp2scp@4a090000 {
compatible = "ti,omap-ocp2scp";
@@ -1190,7 +1187,7 @@
<0x4A096400 0x64>, /* phy_tx */
<0x4A096800 0x40>; /* pll_ctrl */
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
- ctrl-module = <&omap_control_sata>;
+ syscon-phy-power = <&scm_conf 0x374>;
clocks = <&sys_clkin1>, <&sata_ref_clk>;
clock-names = "sysclk", "refclk";
syscon-pllreset = <&scm_conf 0x3fc>;
@@ -1202,16 +1199,18 @@
reg = <0x4a094000 0x80>, /* phy_rx */
<0x4a094400 0x64>; /* phy_tx */
reg-names = "phy_rx", "phy_tx";
- ctrl-module = <&omap_control_pcie1phy>;
+ syscon-phy-power = <&scm_conf_pcie 0x1c>;
+ syscon-pcs = <&scm_conf_pcie 0x10>;
clocks = <&dpll_pcie_ref_ck>,
<&dpll_pcie_ref_m2ldo_ck>,
<&optfclk_pciephy1_32khz>,
<&optfclk_pciephy1_clk>,
<&optfclk_pciephy1_div_clk>,
- <&optfclk_pciephy_div>;
+ <&optfclk_pciephy_div>,
+ <&sys_clkin1>;
clock-names = "dpll_ref", "dpll_ref_m2",
"wkupclk", "refclk",
- "div-clk", "phy-div";
+ "div-clk", "phy-div", "sysclk";
#phy-cells = <0>;
};
@@ -1220,16 +1219,18 @@
reg = <0x4a095000 0x80>, /* phy_rx */
<0x4a095400 0x64>; /* phy_tx */
reg-names = "phy_rx", "phy_tx";
- ctrl-module = <&omap_control_pcie2phy>;
+ syscon-phy-power = <&scm_conf_pcie 0x20>;
+ syscon-pcs = <&scm_conf_pcie 0x10>;
clocks = <&dpll_pcie_ref_ck>,
<&dpll_pcie_ref_m2ldo_ck>,
<&optfclk_pciephy2_32khz>,
<&optfclk_pciephy2_clk>,
<&optfclk_pciephy2_div_clk>,
- <&optfclk_pciephy_div>;
+ <&optfclk_pciephy_div>,
+ <&sys_clkin1>;
clock-names = "dpll_ref", "dpll_ref_m2",
"wkupclk", "refclk",
- "div-clk", "phy-div";
+ "div-clk", "phy-div", "sysclk";
#phy-cells = <0>;
status = "disabled";
};
@@ -1245,23 +1246,6 @@
ti,hwmods = "sata";
};
- omap_control_pcie1phy: control-phy@0x4a003c40 {
- compatible = "ti,control-phy-pcie";
- reg = <0x4a003c40 0x4>, <0x4a003c14 0x4>, <0x4a003c34 0x4>;
- reg-names = "power", "control_sma", "pcie_pcs";
- clocks = <&sys_clkin1>;
- clock-names = "sysclk";
- };
-
- omap_control_pcie2phy: control-pcie@0x4a003c44 {
- compatible = "ti,control-phy-pcie";
- reg = <0x4a003c44 0x4>, <0x4a003c14 0x4>, <0x4a003c34 0x4>;
- reg-names = "power", "control_sma", "pcie_pcs";
- clocks = <&sys_clkin1>;
- clock-names = "sysclk";
- status = "disabled";
- };
-
rtc: rtc@48838000 {
compatible = "ti,am3352-rtc";
reg = <0x48838000 0x100>;
@@ -1271,24 +1255,6 @@
clocks = <&sys_32k_ck>;
};
- omap_control_usb2phy1: control-phy@4a002300 {
- compatible = "ti,control-phy-usb2";
- reg = <0x4a002300 0x4>;
- reg-names = "power";
- };
-
- omap_control_usb3phy1: control-phy@4a002370 {
- compatible = "ti,control-phy-pipe3";
- reg = <0x4a002370 0x4>;
- reg-names = "power";
- };
-
- omap_control_usb2phy2: control-phy@0x4a002e74 {
- compatible = "ti,control-phy-usb2-dra7";
- reg = <0x4a002e74 0x4>;
- reg-names = "power";
- };
-
/* OCP2SCP1 */
ocp2scp@4a080000 {
compatible = "ti,omap-ocp2scp";
@@ -1301,7 +1267,7 @@
usb2_phy1: phy@4a084000 {
compatible = "ti,omap-usb2";
reg = <0x4a084000 0x400>;
- ctrl-module = <&omap_control_usb2phy1>;
+ syscon-phy-power = <&scm_conf 0x300>;
clocks = <&usb_phy1_always_on_clk32k>,
<&usb_otg_ss1_refclk960m>;
clock-names = "wkupclk",
@@ -1310,9 +1276,10 @@
};
usb2_phy2: phy@4a085000 {
- compatible = "ti,omap-usb2";
+ compatible = "ti,dra7x-usb2-phy2",
+ "ti,omap-usb2";
reg = <0x4a085000 0x400>;
- ctrl-module = <&omap_control_usb2phy2>;
+ syscon-phy-power = <&scm_conf 0xe74>;
clocks = <&usb_phy2_always_on_clk32k>,
<&usb_otg_ss2_refclk960m>;
clock-names = "wkupclk",
@@ -1326,7 +1293,7 @@
<0x4a084800 0x64>,
<0x4a084c00 0x40>;
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
- ctrl-module = <&omap_control_usb3phy1>;
+ syscon-phy-power = <&scm_conf 0x370>;
clocks = <&usb_phy3_always_on_clk32k>,
<&sys_clkin1>,
<&usb_otg_ss1_refclk960m>;
@@ -1357,7 +1324,6 @@
"otg";
phys = <&usb2_phy1>, <&usb3_phy1>;
phy-names = "usb2-phy", "usb3-phy";
- tx-fifo-resize;
maximum-speed = "super-speed";
dr_mode = "otg";
snps,dis_u3_susphy_quirk;
@@ -1385,7 +1351,6 @@
"otg";
phys = <&usb2_phy2>;
phy-names = "usb2-phy";
- tx-fifo-resize;
maximum-speed = "high-speed";
dr_mode = "otg";
snps,dis_u3_susphy_quirk;
@@ -1413,7 +1378,6 @@
interrupt-names = "peripheral",
"host",
"otg";
- tx-fifo-resize;
maximum-speed = "high-speed";
dr_mode = "otg";
snps,dis_u3_susphy_quirk;
@@ -1605,6 +1569,8 @@
#include "omap4-cpu-thermal.dtsi"
#include "omap5-gpu-thermal.dtsi"
#include "omap5-core-thermal.dtsi"
+ #include "dra7-dspeve-thermal.dtsi"
+ #include "dra7-iva-thermal.dtsi"
};
};
diff --git a/arch/arm/boot/dts/dra74x.dtsi b/arch/arm/boot/dts/dra74x.dtsi
index 8bcc47d..4220eef 100644
--- a/arch/arm/boot/dts/dra74x.dtsi
+++ b/arch/arm/boot/dts/dra74x.dtsi
@@ -76,7 +76,6 @@
interrupt-names = "peripheral",
"host",
"otg";
- tx-fifo-resize;
maximum-speed = "high-speed";
dr_mode = "otg";
};
diff --git a/arch/arm/boot/dts/logicpd-som-lv-37xx-devkit.dts b/arch/arm/boot/dts/logicpd-som-lv-37xx-devkit.dts
new file mode 100644
index 0000000..da85984
--- /dev/null
+++ b/arch/arm/boot/dts/logicpd-som-lv-37xx-devkit.dts
@@ -0,0 +1,268 @@
+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include "omap36xx.dtsi"
+#include "logicpd-som-lv.dtsi"
+#include "omap-gpmc-smsc9221.dtsi"
+
+/ {
+ model = "LogicPD Zoom DM3730 SOM-LV Development Kit";
+ compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3630", "ti,omap3";
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_key_pins>;
+
+ sysboot2 {
+ label = "gpio3";
+ gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* gpio_111 / uP_GPIO_3 */
+ linux,code = <BTN_0>;
+ wakeup-source;
+ };
+ };
+
+ sound {
+ compatible = "ti,omap-twl4030";
+ ti,model = "omap3logic";
+ ti,mcbsp = <&mcbsp2>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins &led_pins_wkup>;
+
+ led1 {
+ label = "led1";
+ gpios = <&gpio5 5 GPIO_ACTIVE_LOW>; /* gpio133 */
+ linux,default-trigger = "cpu0";
+ };
+
+ led2 {
+ label = "led2";
+ gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; /* gpio11 */
+ linux,default-trigger = "none";
+ };
+ };
+};
+
+&vaux1 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+};
+
+&vaux4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+};
+
+&mcbsp2 {
+ status = "okay";
+};
+
+&charger {
+ ti,bb-uvolt = <3200000>;
+ ti,bb-uamp = <150>;
+};
+
+&gpmc {
+ ranges = <1 0 0x08000000 0x1000000>; /* CS1: 16MB for LAN9221 */
+
+ ethernet@gpmc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lan9221_pins>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <24 IRQ_TYPE_LEVEL_LOW>; /* gpio_152 */
+ reg = <1 0 0xff>;
+ };
+};
+
+&vpll2 {
+ regulator-always-on;
+};
+
+&dss {
+ status = "ok";
+ vdds_dsi-supply = <&vpll2>;
+ vdda_video-supply = <&video_reg>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&dss_dpi_pins1>;
+ port {
+ dpi_out: endpoint {
+ remote-endpoint = <&lcd_in>;
+ data-lines = <16>;
+ };
+ };
+};
+
+/ {
+ aliases {
+ display0 = &lcd0;
+ };
+
+ video_reg: video_reg {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-supply";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ lcd0: display@0 {
+ compatible = "panel-dpi";
+ label = "28";
+ status = "okay";
+ /* default-on; */
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_enable_pin>;
+ enable-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd INI */
+ port {
+ lcd_in: endpoint {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+
+ panel-timing {
+ clock-frequency = <9000000>;
+ hactive = <480>;
+ vactive = <272>;
+ hfront-porch = <3>;
+ hback-porch = <2>;
+ hsync-len = <42>;
+ vback-porch = <3>;
+ vfront-porch = <2>;
+ vsync-len = <11>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+
+ bl: backlight {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&backlight_pins>;
+ pwms = <&twl_pwm 0 5000000>;
+ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <7>;
+ enable-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; /* gpio_8 */
+ };
+};
+
+&mmc1 {
+ interrupts-extended = <&intc 83 &omap3_pmx_core 0x11a>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins &mmc1_cd>;
+ wp-gpios = <&gpio4 30 GPIO_ACTIVE_HIGH>; /* gpio_126 */
+ cd-gpios = <&gpio4 14 IRQ_TYPE_LEVEL_LOW>; /* gpio_110 */
+ vmmc-supply = <&vmmc1>;
+ bus-width = <4>;
+ cap-power-off-card;
+};
+
+&omap3_pmx_core {
+ gpio_key_pins: pinmux_gpio_key_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x212e, PIN_INPUT_PULLUP | MUX_MODE4) /* cam_xclkb.gpio_111 / uP_GPIO_3*/
+ >;
+ };
+
+ led_pins: pinmux_led_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x215e, PIN_OUTPUT_PULLUP | MUX_MODE4) /* sdmmc2_dat1.gpio_133 / uP_GPIO_0 */
+ >;
+ };
+
+ lan9221_pins: pinmux_lan9221_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */
+ >;
+ };
+
+ mmc1_pins: pinmux_mmc1_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */
+ OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */
+ OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */
+ OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */
+ OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */
+ OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
+ OMAP3_CORE1_IOPAD(0x2132, PIN_INPUT_PULLUP | MUX_MODE4) /* cam_strobe.gpio_126 sdmmc1_wp*/
+ >;
+ };
+
+ lcd_enable_pin: pinmux_lcd_enable_pin {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* mcbsp4_fs.gpio_155 */
+ >;
+ };
+
+ dss_dpi_pins1: pinmux_dss_dpi_pins1 {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_pclk.dss_pclk */
+ OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_hsync.dss_hsync */
+ OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_vsync.dss_vsync */
+ OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_acbias.dss_acbias */
+
+ OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data0.dss_data0 */
+ OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data1.dss_data1 */
+ OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data2.dss_data2 */
+ OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data3.dss_data3 */
+ OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data4.dss_data4 */
+ OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data5.dss_data5 */
+ OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data6.dss_data6 */
+ OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data7.dss_data7 */
+ OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data8.dss_data8 */
+ OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data9.dss_data9 */
+ OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data10.dss_data10 */
+ OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data11.dss_data11 */
+ OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data12.dss_data12 */
+ OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data13.dss_data13 */
+ OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data14.dss_data14 */
+ OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data15.dss_data15 */
+ >;
+ };
+};
+
+&omap3_pmx_wkup {
+ led_pins_wkup: pinmux_led_pins_wkup {
+ pinctrl-single,pins = <
+ OMAP3_WKUP_IOPAD(0x2a24, PIN_OUTPUT_PULLUP | MUX_MODE4) /* jtag_emu0.gpio_11 / uP_GPIO_1 */
+ >;
+ };
+
+ backlight_pins: pinmux_backlight_pins {
+ pinctrl-single,pins = <
+ OMAP3_WKUP_IOPAD(0x2a16, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* sys_boot6.gpio_8 */
+ >;
+ };
+
+ mmc1_cd: pinmux_mmc1_cd {
+ pinctrl-single,pins = <
+ OMAP3_WKUP_IOPAD(0x212c, PIN_INPUT_PULLUP | MUX_MODE4) /* cam_d11.gpio_110 */
+ >;
+ };
+};
+
+
+&uart1 {
+ interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>;
+};
+
+/* Wired to the tps65950 on the SOM, only the USB connector is on the devkit */
+&usb_otg_hs {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hsusb_otg_pins>;
+ interface-type = <0>;
+ usb-phy = <&usb2_phy>;
+ phys = <&usb2_phy>;
+ phy-names = "usb2-phy";
+ mode = <3>;
+ power = <50>;
+};
diff --git a/arch/arm/boot/dts/logicpd-som-lv.dtsi b/arch/arm/boot/dts/logicpd-som-lv.dtsi
new file mode 100644
index 0000000..365f39ff
--- /dev/null
+++ b/arch/arm/boot/dts/logicpd-som-lv.dtsi
@@ -0,0 +1,265 @@
+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <dt-bindings/input/input.h>
+
+/ {
+ cpus {
+ cpu@0 {
+ cpu0-supply = <&vcc>;
+ };
+ };
+
+ wl12xx_vmmc: wl12xx_vmmc {
+ compatible = "regulator-fixed";
+ regulator-name = "vwl1271";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&gpio1 3 0>; /* gpio_3 */
+ startup-delay-us = <70000>;
+ enable-active-high;
+ vin-supply = <&vmmc2>;
+ };
+
+ /* HS USB Host PHY on PORT 1 */
+ hsusb2_phy: hsusb2_phy {
+ compatible = "usb-nop-xceiv";
+ reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */
+ };
+};
+
+&gpmc {
+ ranges = <0 0 0x00000000 0x1000000>; /* CS0: 16MB for NAND */
+
+ nand@0,0 {
+ linux,mtd-name = "micron,mt29f4g16abbda3w";
+ reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+ nand-bus-width = <16>;
+ ti,nand-ecc-opt = "bch8";
+ gpmc,sync-clk-ps = <0>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <44>;
+ gpmc,cs-wr-off-ns = <44>;
+ gpmc,adv-on-ns = <6>;
+ gpmc,adv-rd-off-ns = <34>;
+ gpmc,adv-wr-off-ns = <44>;
+ gpmc,we-off-ns = <40>;
+ gpmc,oe-off-ns = <54>;
+ gpmc,access-ns = <64>;
+ gpmc,rd-cycle-ns = <82>;
+ gpmc,wr-cycle-ns = <82>;
+ gpmc,wr-access-ns = <40>;
+ gpmc,wr-data-mux-bus-ns = <0>;
+ gpmc,device-width = <2>;
+
+ gpmc,page-burst-access-ns = <5>;
+ gpmc,cycle2cycle-delay-ns = <50>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /* u-boot uses mtdparts=omap2-nand.0:512k(x-loader),1920k(u-boot),128k(u-boot-env),4m(kernel),-(fs) */
+
+ x-loader@0 {
+ label = "x-loader";
+ reg = <0 0x80000>;
+ };
+
+ bootloaders@80000 {
+ label = "u-boot";
+ reg = <0x80000 0x1e0000>;
+ };
+
+ bootloaders_env@260000 {
+ label = "u-boot-env";
+ reg = <0x260000 0x20000>;
+ };
+
+ kernel@280000 {
+ label = "kernel";
+ reg = <0x280000 0x400000>;
+ };
+
+ filesystem@680000 {
+ label = "fs";
+ reg = <0x680000 0>; /* 0 = MTDPART_SIZ_FULL */
+ };
+ };
+};
+
+&i2c1 {
+ clock-frequency = <2600000>;
+
+ twl: twl@48 {
+ reg = <0x48>;
+ interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+ interrupt-parent = <&intc>;
+ twl_audio: audio {
+ compatible = "ti,twl4030-audio";
+ codec {
+ };
+ };
+ };
+};
+
+&i2c2 {
+ clock-frequency = <400000>;
+};
+
+&i2c3 {
+ clock-frequency = <400000>;
+};
+
+&mmc3 {
+ interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>;
+ pinctrl-0 = <&mmc3_pins>;
+ pinctrl-names = "default";
+ vmmc-supply = <&wl12xx_vmmc>;
+ non-removable;
+ bus-width = <4>;
+ cap-power-off-card;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ wlcore: wlcore@2 {
+ compatible = "ti,wl1273";
+ reg = <2>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */
+ ref-clock-frequency = <26000000>;
+ };
+};
+
+&usbhshost {
+ port2-mode = "ehci-phy";
+};
+
+&usbhsehci {
+ phys = <0 &hsusb2_phy>;
+};
+
+
+&omap3_pmx_core {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hsusb2_pins>;
+
+ mmc3_pins: pinmux_mm3_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */
+ OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */
+ OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */
+ OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */
+ OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */
+ OMAP3_CORE1_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4) /* sys_boot1.gpio_3 */
+ OMAP3_CORE1_IOPAD(0x21d0, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs1.sdmmc3_cmd */
+ OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs2.sdmmc_clk */
+ >;
+ };
+ mcbsp2_pins: pinmux_mcbsp2_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx */
+ OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0) /* mcbsp2_clkx */
+ OMAP3_CORE1_IOPAD(0x2140, PIN_INPUT | MUX_MODE0) /* mcbsp2_dr */
+ OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0) /* mcbsp2_dx */
+ >;
+ };
+ uart2_pins: pinmux_uart2_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0) /* uart2_cts.uart2_cts */
+ OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0) /* uart2_rts .uart2_rts*/
+ OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */
+ OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */
+ OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4) /* GPIO_162,BT_EN */
+ >;
+ };
+ mcspi1_pins: pinmux_mcspi1_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */
+ OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */
+ OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */
+ OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */
+ >;
+ };
+
+ hsusb2_pins: pinmux_hsusb2_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */
+ OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */
+ OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */
+ OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */
+ OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */
+ OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */
+ >;
+ };
+
+ hsusb_otg_pins: pinmux_hsusb_otg_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */
+ OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */
+ OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */
+ OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */
+ OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT | MUX_MODE0) /* hsusb0_data0.hsusb0_data0 */
+ OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */
+ OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */
+ OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT | MUX_MODE0) /* hsusb0_data3.hsusb0_data3 */
+ OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT | MUX_MODE0) /* hsusb0_data4.hsusb0_data4 */
+ OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT | MUX_MODE0) /* hsusb0_data5.hsusb0_data5 */
+ OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT | MUX_MODE0) /* hsusb0_data6.hsusb0_data6 */
+ OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */
+ >;
+ };
+
+
+};
+
+&omap3_pmx_wkup {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hsusb2_reset_pin>;
+ hsusb2_reset_pin: pinmux_hsusb1_reset_pin {
+ pinctrl-single,pins = <
+ OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4) /* sys_boot2.gpio_4 */
+ >;
+ };
+};
+
+&omap3_pmx_core2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hsusb2_2_pins>;
+ hsusb2_2_pins: pinmux_hsusb2_2_pins {
+ pinctrl-single,pins = <
+ OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */
+ OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */
+ OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */
+ OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */
+ OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */
+ OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */
+ >;
+ };
+};
+
+&uart2 {
+ interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+};
+
+&mcspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcspi1_pins>;
+};
+
+#include "twl4030.dtsi"
+#include "twl4030_omap3.dtsi"
+
+&twl {
+ twl_power: power {
+ compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle";
+ ti,use_poweroff;
+ };
+};
+
+&twl_gpio {
+ ti,use-leds;
+};
diff --git a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts
index d0211fc..3f91b60 100644
--- a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts
+++ b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts
@@ -71,6 +71,15 @@
linux,default-trigger = "none";
};
};
+
+ pwm10: dmtimer-pwm@10 {
+ compatible = "ti,omap-dmtimer-pwm";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm_pins>;
+ ti,timers = <&timer10>;
+ #pwm-cells = <3>;
+ };
+
};
&vaux1 {
@@ -112,6 +121,7 @@
&dss {
status = "ok";
vdds_dsi-supply = <&vpll2>;
+ vdda_video-supply = <&video_reg>;
pinctrl-names = "default";
pinctrl-0 = <&dss_dpi_pins1>;
port {
@@ -127,13 +137,22 @@
display0 = &lcd0;
};
+ video_reg: video_reg {
+ pinctrl-names = "default";
+ pinctrl-0 = <&panel_pwr_pins>;
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-supply";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd INI */
+ };
+
lcd0: display@0 {
compatible = "panel-dpi";
label = "15";
status = "okay";
/* default-on; */
pinctrl-names = "default";
- enable-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>; /* gpio155, lcd INI */
port {
lcd_in: endpoint {
@@ -159,13 +178,13 @@
};
bl: backlight {
- compatible = "gpio-backlight";
+ compatible = "pwm-backlight";
pinctrl-names = "default";
pinctrl-0 = <&backlight_pins>;
-
- gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>, /* gpio_56 */
- <&gpio5 26 GPIO_ACTIVE_HIGH>; /* gpio_154 */
- default-on;
+ pwms = <&pwm10 0 5000000 0>;
+ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <7>;
+ enable-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH>; /* gpio_154 */
};
};
@@ -187,6 +206,12 @@
>;
};
+ pwm_pins: pinmux_pwm_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x20B8, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* gpmc_ncs5.gpt_10_pwm_evt */
+ >;
+ };
+
led_pins: pinmux_led_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x21d8, PIN_OUTPUT | MUX_MODE4) /* gpio_179 */
@@ -213,37 +238,60 @@
backlight_pins: pinmux_backlight_pins {
pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x20B8, PIN_OUTPUT | MUX_MODE4) /* gpmc_ncs5.gpio_56 */
- OMAP3_CORE1_IOPAD(0x2188, PIN_OUTPUT | MUX_MODE4) /* mcbsp4_dx.gpio_154 */
+ OMAP3_CORE1_IOPAD(0x2188, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* mcbsp4_dx.gpio_154 */
+ >;
+ };
+
+ isp_pins: pinmux_isp_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x210c, PIN_INPUT | MUX_MODE0) /* cam_hs.cam_hs */
+ OMAP3_CORE1_IOPAD(0x210e, PIN_INPUT | MUX_MODE0) /* cam_vs.cam_vs */
+ OMAP3_CORE1_IOPAD(0x2110, PIN_INPUT | MUX_MODE0) /* cam_xclka.cam_xclka */
+ OMAP3_CORE1_IOPAD(0x2112, PIN_INPUT | MUX_MODE0) /* cam_pclk.cam_pclk */
+
+ OMAP3_CORE1_IOPAD(0x2114, PIN_INPUT | MUX_MODE0) /* cam_d0.cam_d0 */
+ OMAP3_CORE1_IOPAD(0x2116, PIN_INPUT | MUX_MODE0) /* cam_d1.cam_d1 */
+ OMAP3_CORE1_IOPAD(0x2118, PIN_INPUT | MUX_MODE0) /* cam_d2.cam_d2 */
+ OMAP3_CORE1_IOPAD(0x211c, PIN_INPUT | MUX_MODE0) /* cam_d3.cam_d3 */
+ OMAP3_CORE1_IOPAD(0x211e, PIN_INPUT | MUX_MODE0) /* cam_d4.cam_d4 */
+ OMAP3_CORE1_IOPAD(0x2120, PIN_INPUT | MUX_MODE0) /* cam_d5.cam_d5 */
+ OMAP3_CORE1_IOPAD(0x2122, PIN_INPUT | MUX_MODE0) /* cam_d6.cam_d6 */
+ OMAP3_CORE1_IOPAD(0x2124, PIN_INPUT | MUX_MODE0) /* cam_d7.cam_d7 */
+ >;
+ };
+
+ panel_pwr_pins: pinmux_panel_pwr_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | PIN_OFF_OUTPUT_LOW | MUX_MODE4) /* mcbsp4_fs.gpio_155 */
>;
};
dss_dpi_pins1: pinmux_dss_dpi_pins1 {
pinctrl-single,pins = <
- OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */
- OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */
- OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */
- OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */
+ OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_pclk.dss_pclk */
+ OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_hsync.dss_hsync */
+ OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_vsync.dss_vsync */
+ OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_acbias.dss_acbias */
- OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */
- OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */
- OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */
- OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */
- OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */
- OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */
- OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */
- OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */
- OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */
- OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */
- OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */
- OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */
+ OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data6.dss_data6 */
+ OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data7.dss_data7 */
+ OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data8.dss_data8 */
+ OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data9.dss_data9 */
+ OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data10.dss_data10 */
+ OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data11.dss_data11 */
+ OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data12.dss_data12 */
+ OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data13.dss_data13 */
+ OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data14.dss_data14 */
+ OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data15.dss_data15 */
+ OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data16.dss_data16 */
+ OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE0) /* dss_data17.dss_data17 */
- OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE3) /* dss_data18.dss_data0 */
- OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE3) /* dss_data19.dss_data1 */
- OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE3) /* dss_data20.dss_data2 */
- OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE3) /* dss_data21.dss_data3 */
- OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE3) /* dss_data22.dss_data4 */
- OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE3) /* dss_data23.dss_data5 */
+ OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data18.dss_data0 */
+ OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data19.dss_data1 */
+ OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data20.dss_data2 */
+ OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data21.dss_data3 */
+ OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data22.dss_data4 */
+ OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT_PULLDOWN | PIN_OFF_OUTPUT_LOW | MUX_MODE3) /* dss_data23.dss_data5 */
>;
};
};
@@ -269,6 +317,24 @@
};
};
+&i2c2 {
+ mt9p031@48 {
+ compatible = "aptina,mt9p031";
+ reg = <0x48>;
+ clocks = <&isp 0>;
+ vaa-supply = <&vaux4>;
+ vdd-supply = <&vaux4>;
+ vdd_io-supply = <&vaux4>;
+ port {
+ mt9p031_out: endpoint {
+ input-clock-frequency = <24000000>;
+ pixel-clock-frequency = <72000000>;
+ remote-endpoint = <&ccdc_ep>;
+ };
+ };
+ };
+};
+
&i2c3 {
touchscreen: tsc2004@48 {
compatible = "ti,tsc2004";
@@ -290,12 +356,45 @@
};
};
+&mcspi1 {
+ at25@0 {
+ compatible = "atmel,at25";
+ reg = <0>;
+ spi-max-frequency = <5000000>;
+ spi-cpha;
+ spi-cpol;
+
+ pagesize = <64>;
+ size = <32768>;
+ address-width = <16>;
+ };
+};
+
+&isp {
+ pinctrl-names = "default";
+ pinctrl-0 = <&isp_pins>;
+ ports {
+ port@0 {
+ reg = <0>;
+ ccdc_ep: endpoint {
+ remote-endpoint = <&mt9p031_out>;
+ bus-width = <8>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ pclk-sample = <0>;
+ };
+ };
+ };
+};
+
&uart1 {
interrupts-extended = <&intc 72 &omap3_pmx_core OMAP3_UART1_RX>;
};
/* Wired to the tps65950 on the SOM, only the USB connector is on the devkit */
&usb_otg_hs {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hsusb_otg_pins>;
interface-type = <0>;
usb-phy = <&usb2_phy>;
phys = <&usb2_phy>;
diff --git a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi
index b46789a..ed8a62a 100644
--- a/arch/arm/boot/dts/logicpd-torpedo-som.dtsi
+++ b/arch/arm/boot/dts/logicpd-torpedo-som.dtsi
@@ -122,6 +122,11 @@
&i2c3 {
clock-frequency = <400000>;
+ at24@50 {
+ compatible = "at24,24c02";
+ readonly;
+ reg = <0x50>;
+ };
};
/*
@@ -178,6 +183,31 @@
OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4) /* GPIO_162,BT_EN */
>;
};
+ mcspi1_pins: pinmux_mcspi1_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */
+ OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */
+ OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */
+ OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */
+ >;
+ };
+ hsusb_otg_pins: pinmux_hsusb_otg_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */
+ OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */
+ OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */
+ OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */
+
+ OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT | MUX_MODE0) /* hsusb0_data0.hsusb0_data0 */
+ OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */
+ OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */
+ OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT | MUX_MODE0) /* hsusb0_data3.hsusb0_data3 */
+ OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT | MUX_MODE0) /* hsusb0_data4.hsusb0_data4 */
+ OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT | MUX_MODE0) /* hsusb0_data5.hsusb0_data5 */
+ OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT | MUX_MODE0) /* hsusb0_data6.hsusb0_data6 */
+ OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */
+ >;
+ };
};
&uart2 {
@@ -186,6 +216,11 @@
pinctrl-0 = <&uart2_pins>;
};
+&mcspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcspi1_pins>;
+};
+
&omap3_pmx_core2 {
mmc3_core2_pins: pinmux_mmc3_core2_pins {
pinctrl-single,pins = <
diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi
index 81aec99..41f5d38 100644
--- a/arch/arm/boot/dts/omap3-igep.dtsi
+++ b/arch/arm/boot/dts/omap3-igep.dtsi
@@ -18,6 +18,10 @@
reg = <0x80000000 0x20000000>; /* 512 MB */
};
+ chosen {
+ stdout-path = &uart3;
+ };
+
sound {
compatible = "ti,omap-twl4030";
ti,model = "igep2";
diff --git a/arch/arm/boot/dts/omap3-igep0030-common.dtsi b/arch/arm/boot/dts/omap3-igep0030-common.dtsi
index cd91ef0..e94d942 100644
--- a/arch/arm/boot/dts/omap3-igep0030-common.dtsi
+++ b/arch/arm/boot/dts/omap3-igep0030-common.dtsi
@@ -33,9 +33,28 @@
default-state = "off";
};
};
+
+ hsusb2_phy: hsusb2_phy {
+ compatible = "usb-nop-xceiv";
+ reset-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>; /* gpio_54 */
+ };
};
&omap3_pmx_core {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hsusb2_pins>;
+
+ hsusb2_pins: pinmux_hsusb2_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */
+ OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */
+ OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */
+ OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */
+ OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */
+ OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */
+ >;
+ };
+
uart2_pins: pinmux_uart2_pins {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x216c, PIN_INPUT | MUX_MODE1) /* mcbsp3_dx.uart2_cts */
@@ -47,6 +66,20 @@
};
&omap3_pmx_core2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hsusb2_core2_pins>;
+
+ hsusb2_core2_pins: pinmux_hsusb2_core2_pins {
+ pinctrl-single,pins = <
+ OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */
+ OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */
+ OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */
+ OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */
+ OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */
+ OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */
+ >;
+ };
+
leds_core2_pins: pinmux_leds_core2_pins {
pinctrl-single,pins = <
OMAP3630_CORE2_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE4) /* etk_d2.gpio_16 */
@@ -54,6 +87,14 @@
};
};
+&usbhshost {
+ port2-mode = "ehci-phy";
+};
+
+&usbhsehci {
+ phys = <0 &hsusb2_phy>;
+};
+
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&uart2_pins>;
diff --git a/arch/arm/boot/dts/omap3-n9.dts b/arch/arm/boot/dts/omap3-n9.dts
index f2e2139..5c67429 100644
--- a/arch/arm/boot/dts/omap3-n9.dts
+++ b/arch/arm/boot/dts/omap3-n9.dts
@@ -53,3 +53,7 @@
};
};
};
+
+&modem {
+ compatible = "nokia,n9-modem";
+};
diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts
index 74d8f7eb..152511b 100644
--- a/arch/arm/boot/dts/omap3-n900.dts
+++ b/arch/arm/boot/dts/omap3-n900.dts
@@ -65,45 +65,46 @@
camera_lens_cover {
label = "Camera Lens Cover";
gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; /* 110 */
- linux,input-type = <5>; /* EV_SW */
- linux,code = <0x09>; /* SW_CAMERA_LENS_COVER */
- wakeup-source;
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_CAMERA_LENS_COVER>;
+ linux,can-disable;
};
camera_focus {
label = "Camera Focus";
gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; /* 68 */
- linux,code = <0x210>; /* KEY_CAMERA_FOCUS */
- wakeup-source;
+ linux,code = <KEY_CAMERA_FOCUS>;
+ linux,can-disable;
};
camera_capture {
label = "Camera Capture";
gpios = <&gpio3 5 GPIO_ACTIVE_LOW>; /* 69 */
- linux,code = <0xd4>; /* KEY_CAMERA */
- wakeup-source;
+ linux,code = <KEY_CAMERA>;
+ linux,can-disable;
};
lock_button {
label = "Lock Button";
gpios = <&gpio4 17 GPIO_ACTIVE_LOW>; /* 113 */
- linux,code = <0x98>; /* KEY_SCREENLOCK */
- wakeup-source;
+ linux,code = <KEY_SCREENLOCK>;
+ linux,can-disable;
};
keypad_slide {
label = "Keypad Slide";
gpios = <&gpio3 7 GPIO_ACTIVE_LOW>; /* 71 */
- linux,input-type = <5>; /* EV_SW */
- linux,code = <0x0a>; /* SW_KEYPAD_SLIDE */
- wakeup-source;
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_KEYPAD_SLIDE>;
+ linux,can-disable;
};
proximity_sensor {
label = "Proximity Sensor";
gpios = <&gpio3 25 GPIO_ACTIVE_HIGH>; /* 89 */
- linux,input-type = <5>; /* EV_SW */
- linux,code = <0x0b>; /* SW_FRONT_PROXIMITY */
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_FRONT_PROXIMITY>;
+ linux,can-disable;
};
};
@@ -522,6 +523,21 @@
amstaos,cover-comp-gain = <16>;
};
+ adp1653: led-controller@30 {
+ compatible = "adi,adp1653";
+ reg = <0x30>;
+ enable-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>; /* 88 */
+
+ flash {
+ flash-timeout-us = <500000>;
+ flash-max-microamp = <320000>;
+ led-max-microamp = <50000>;
+ };
+ indicator {
+ led-max-microamp = <17500>;
+ };
+ };
+
lp5523: lp5523@32 {
compatible = "national,lp5523";
reg = <0x32>;
diff --git a/arch/arm/boot/dts/omap3-n950-n9.dtsi b/arch/arm/boot/dts/omap3-n950-n9.dtsi
index a2c2b8d..858a250 100644
--- a/arch/arm/boot/dts/omap3-n950-n9.dtsi
+++ b/arch/arm/boot/dts/omap3-n950-n9.dtsi
@@ -31,6 +31,14 @@
startup-delay-us = <150>;
enable-active-high;
};
+
+ vwlan_fixed: fixedregulator@2 {
+ compatible = "regulator-fixed";
+ regulator-name = "VWLAN";
+ gpio = <&gpio2 3 GPIO_ACTIVE_HIGH>; /* gpio 35 */
+ enable-active-high;
+ regulator-boot-off;
+ };
};
&omap3_pmx_core {
@@ -44,6 +52,55 @@
OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3 */
>;
};
+
+ wlan_pins: pinmux_wlan_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x207c, PIN_OUTPUT | MUX_MODE4) /* gpio 35 - wlan enable */
+ OMAP3_CORE1_IOPAD(0x208a, PIN_INPUT | MUX_MODE4) /* gpio 42 - wlan irq */
+ >;
+ };
+
+ ssi_pins: pinmux_ssi_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE1) /* ssi1_dat_tx */
+ OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE1) /* ssi1_flag_tx */
+ OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT_PULLUP | MUX_MODE1) /* ssi1_rdy_tx */
+ OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | WAKEUP_EN | MUX_MODE4) /* ssi1_wake_tx (cawake) */
+ OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT | MUX_MODE1) /* ssi1_dat_rx */
+ OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE1) /* ssi1_flag_rx */
+ OMAP3_CORE1_IOPAD(0x2188, PIN_OUTPUT | MUX_MODE1) /* ssi1_rdy_rx */
+ OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | MUX_MODE1) /* ssi1_wake */
+ >;
+ };
+
+ ssi_pins_idle: pinmux_ssi_pins_idle {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE7) /* ssi1_dat_tx */
+ OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE7) /* ssi1_flag_tx */
+ OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT_PULLDOWN | MUX_MODE7) /* ssi1_rdy_tx */
+ OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | WAKEUP_EN | MUX_MODE4) /* ssi1_wake_tx (cawake) */
+ OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT | MUX_MODE7) /* ssi1_dat_rx */
+ OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE7) /* ssi1_flag_rx */
+ OMAP3_CORE1_IOPAD(0x2188, PIN_OUTPUT | MUX_MODE4) /* ssi1_rdy_rx */
+ OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | MUX_MODE7) /* ssi1_wake */
+ >;
+ };
+
+ modem_pins1: pinmux_modem_core1_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x207a, PIN_INPUT | WAKEUP_EN | MUX_MODE4) /* gpio_34 (ape_rst_rq) */
+ OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE4) /* gpio_88 (cmt_rst_rq) */
+ OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE4) /* gpio_93 (cmt_apeslpx) */
+ >;
+ };
+};
+
+&omap3_pmx_core2 {
+ modem_pins2: pinmux_modem_core2_pins {
+ pinctrl-single,pins = <
+ OMAP3630_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4) /* gpio_23 (cmt_en) */
+ >;
+ };
};
&i2c1 {
@@ -191,3 +248,39 @@
};
};
};
+
+&ssi_port1 {
+ pinctrl-names = "default", "idle";
+ pinctrl-0 = <&ssi_pins>;
+ pinctrl-1 = <&ssi_pins_idle>;
+
+ ti,ssi-cawake-gpio = <&gpio5 23 GPIO_ACTIVE_HIGH>; /* 151 */
+
+ modem: hsi-client {
+ pinctrl-names = "default";
+ pinctrl-0 = <&modem_pins1 &modem_pins2>;
+
+ hsi-channel-ids = <0>, <1>, <2>, <3>;
+ hsi-channel-names = "mcsaab-control",
+ "speech-control",
+ "speech-data",
+ "mcsaab-data";
+ hsi-speed-kbps = <96000>;
+ hsi-mode = "frame";
+ hsi-flow = "synchronized";
+ hsi-arb-mode = "round-robin";
+
+ interrupts-extended = <&gpio2 2 IRQ_TYPE_EDGE_RISING>; /* gpio 34 */
+
+ gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>, /* gpio 93 */
+ <&gpio3 24 GPIO_ACTIVE_HIGH>, /* gpio 88 */
+ <&gpio1 23 GPIO_ACTIVE_HIGH>; /* gpio 23 */
+ gpio-names = "cmt_apeslpx",
+ "cmt_rst_rq",
+ "cmt_en";
+ };
+};
+
+&ssi_port2 {
+ status = "disabled";
+};
diff --git a/arch/arm/boot/dts/omap3-n950.dts b/arch/arm/boot/dts/omap3-n950.dts
index 0885b34..7f219a9 100644
--- a/arch/arm/boot/dts/omap3-n950.dts
+++ b/arch/arm/boot/dts/omap3-n950.dts
@@ -17,6 +17,17 @@
compatible = "nokia,omap3-n950", "ti,omap36xx", "ti,omap3";
};
+&omap3_pmx_core {
+ spi4_pins: pinmux_spi4_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x218c, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mcspi4_clk */
+ OMAP3_CORE1_IOPAD(0x2190, PIN_OUTPUT | MUX_MODE1) /* mcspi4_simo */
+ OMAP3_CORE1_IOPAD(0x2192, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mcspi4_somi */
+ OMAP3_CORE1_IOPAD(0x2196, PIN_OUTPUT | MUX_MODE1) /* mcspi4_cs0 */
+ >;
+ };
+};
+
&i2c2 {
smia_1: camera@10 {
compatible = "nokia,smia";
@@ -53,3 +64,25 @@
};
};
};
+
+&mcspi4 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi4_pins>;
+
+ wlcore: wlcore@0 {
+ compatible = "ti,wl1271";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlan_pins>;
+ reg = <0>;
+ spi-max-frequency = <48000000>;
+ clock-xtal;
+ ref-clock-frequency = <38400000>;
+ interrupts-extended = <&gpio2 10 IRQ_TYPE_LEVEL_HIGH>; /* gpio 42 */
+ vwlan-supply = <&vwlan_fixed>;
+ };
+};
+
+&modem {
+ compatible = "nokia,n950-modem";
+};
diff --git a/arch/arm/boot/dts/omap34xx.dtsi b/arch/arm/boot/dts/omap34xx.dtsi
index 4f6b2d5..387dc31 100644
--- a/arch/arm/boot/dts/omap34xx.dtsi
+++ b/arch/arm/boot/dts/omap34xx.dtsi
@@ -54,6 +54,12 @@
#size-cells = <0>;
};
};
+
+ bandgap {
+ reg = <0x48002524 0x4>;
+ compatible = "ti,omap34xx-bandgap";
+ #thermal-sensor-cells = <0>;
+ };
};
};
diff --git a/arch/arm/boot/dts/omap36xx.dtsi b/arch/arm/boot/dts/omap36xx.dtsi
index 86253de..f19c87b 100644
--- a/arch/arm/boot/dts/omap36xx.dtsi
+++ b/arch/arm/boot/dts/omap36xx.dtsi
@@ -86,6 +86,12 @@
#size-cells = <0>;
};
};
+
+ bandgap {
+ reg = <0x48002524 0x4>;
+ compatible = "ti,omap36xx-bandgap";
+ #thermal-sensor-cells = <0>;
+ };
};
};
diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
index ca3c17f..38805eb 100644
--- a/arch/arm/boot/dts/omap5.dtsi
+++ b/arch/arm/boot/dts/omap5.dtsi
@@ -852,18 +852,6 @@
hw-caps-temp-alert;
};
- omap_control_usb2phy: control-phy@4a002300 {
- compatible = "ti,control-phy-usb2";
- reg = <0x4a002300 0x4>;
- reg-names = "power";
- };
-
- omap_control_usb3phy: control-phy@4a002370 {
- compatible = "ti,control-phy-pipe3";
- reg = <0x4a002370 0x4>;
- reg-names = "power";
- };
-
usb3: omap_dwc3@4a020000 {
compatible = "ti,dwc3";
ti,hwmods = "usb_otg_ss";
@@ -885,7 +873,6 @@
phys = <&usb2_phy>, <&usb3_phy>;
phy-names = "usb2-phy", "usb3-phy";
dr_mode = "peripheral";
- tx-fifo-resize;
};
};
@@ -899,7 +886,7 @@
usb2_phy: usb2phy@4a084000 {
compatible = "ti,omap-usb2";
reg = <0x4a084000 0x7c>;
- ctrl-module = <&omap_control_usb2phy>;
+ syscon-phy-power = <&scm_conf 0x300>;
clocks = <&usb_phy_cm_clk32k>, <&usb_otg_ss_refclk960m>;
clock-names = "wkupclk", "refclk";
#phy-cells = <0>;
@@ -911,7 +898,7 @@
<0x4a084800 0x64>,
<0x4a084c00 0x40>;
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
- ctrl-module = <&omap_control_usb3phy>;
+ syscon-phy-power = <&scm_conf 0x370>;
clocks = <&usb_phy_cm_clk32k>,
<&sys_clkin>,
<&usb_otg_ss_refclk960m>;
@@ -967,14 +954,6 @@
#thermal-sensor-cells = <1>;
};
- omap_control_sata: control-phy@4a002374 {
- compatible = "ti,control-phy-pipe3";
- reg = <0x4a002374 0x4>;
- reg-names = "power";
- clocks = <&sys_clkin>;
- clock-names = "sysclk";
- };
-
/* OCP2SCP3 */
ocp2scp@4a090000 {
compatible = "ti,omap-ocp2scp";
@@ -989,7 +968,7 @@
<0x4A096400 0x64>, /* phy_tx */
<0x4A096800 0x40>; /* pll_ctrl */
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
- ctrl-module = <&omap_control_sata>;
+ syscon-phy-power = <&scm_conf 0x374>;
clocks = <&sys_clkin>, <&sata_ref_clk>;
clock-names = "sysclk", "refclk";
#phy-cells = <0>;