[SCSI] hpsa: Use kernel provided PCI state save and restore functions
and use the doorbell reset method if available (which doesn't
lock up the controller if you properly save and restore all
the PCI registers that you're supposed to.)
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
diff --git a/drivers/scsi/hpsa.c b/drivers/scsi/hpsa.c
index cfd30ad..82b94e2 100644
--- a/drivers/scsi/hpsa.c
+++ b/drivers/scsi/hpsa.c
@@ -3053,38 +3053,6 @@
#define hpsa_soft_reset_controller(p) hpsa_message(p, 1, 0)
#define hpsa_noop(p) hpsa_message(p, 3, 0)
-static __devinit int hpsa_reset_msi(struct pci_dev *pdev)
-{
-/* the #defines are stolen from drivers/pci/msi.h. */
-#define msi_control_reg(base) (base + PCI_MSI_FLAGS)
-#define PCI_MSIX_FLAGS_ENABLE (1 << 15)
-
- int pos;
- u16 control = 0;
-
- pos = pci_find_capability(pdev, PCI_CAP_ID_MSI);
- if (pos) {
- pci_read_config_word(pdev, msi_control_reg(pos), &control);
- if (control & PCI_MSI_FLAGS_ENABLE) {
- dev_info(&pdev->dev, "resetting MSI\n");
- pci_write_config_word(pdev, msi_control_reg(pos),
- control & ~PCI_MSI_FLAGS_ENABLE);
- }
- }
-
- pos = pci_find_capability(pdev, PCI_CAP_ID_MSIX);
- if (pos) {
- pci_read_config_word(pdev, msi_control_reg(pos), &control);
- if (control & PCI_MSIX_FLAGS_ENABLE) {
- dev_info(&pdev->dev, "resetting MSI-X\n");
- pci_write_config_word(pdev, msi_control_reg(pos),
- control & ~PCI_MSIX_FLAGS_ENABLE);
- }
- }
-
- return 0;
-}
-
static int hpsa_controller_hard_reset(struct pci_dev *pdev,
void * __iomem vaddr, bool use_doorbell)
{
@@ -3140,17 +3108,17 @@
*/
static __devinit int hpsa_kdump_hard_reset_controller(struct pci_dev *pdev)
{
- u16 saved_config_space[32];
u64 cfg_offset;
u32 cfg_base_addr;
u64 cfg_base_addr_index;
void __iomem *vaddr;
unsigned long paddr;
u32 misc_fw_support, active_transport;
- int rc, i;
+ int rc;
struct CfgTable __iomem *cfgtable;
bool use_doorbell;
u32 board_id;
+ u16 command_register;
/* For controllers as old as the P600, this is very nearly
* the same thing as
@@ -3160,14 +3128,6 @@
* pci_set_power_state(pci_dev, PCI_D0);
* pci_restore_state(pci_dev);
*
- * but we can't use these nice canned kernel routines on
- * kexec, because they also check the MSI/MSI-X state in PCI
- * configuration space and do the wrong thing when it is
- * set/cleared. Also, the pci_save/restore_state functions
- * violate the ordering requirements for restoring the
- * configuration space from the CCISS document (see the
- * comment below). So we roll our own ....
- *
* For controllers newer than the P600, the pci power state
* method of resetting doesn't work so we have another way
* using the doorbell register.
@@ -3184,9 +3144,13 @@
if (board_id == 0x409C0E11 || board_id == 0x409D0E11)
return -ENOTSUPP;
- for (i = 0; i < 32; i++)
- pci_read_config_word(pdev, 2*i, &saved_config_space[i]);
-
+ /* Save the PCI command register */
+ pci_read_config_word(pdev, 4, &command_register);
+ /* Turn the board off. This is so that later pci_restore_state()
+ * won't turn the board on before the rest of config space is ready.
+ */
+ pci_disable_device(pdev);
+ pci_save_state(pdev);
/* find the first memory BAR, so we can find the cfg table */
rc = hpsa_pci_find_memory_BAR(pdev, &paddr);
@@ -3212,30 +3176,17 @@
misc_fw_support = readl(&cfgtable->misc_fw_support);
use_doorbell = misc_fw_support & MISC_FW_DOORBELL_RESET;
- /* The doorbell reset seems to cause lockups on some Smart
- * Arrays (e.g. P410, P410i, maybe others). Until this is
- * fixed or at least isolated, avoid the doorbell reset.
- */
- use_doorbell = 0;
-
rc = hpsa_controller_hard_reset(pdev, vaddr, use_doorbell);
if (rc)
goto unmap_cfgtable;
- /* Restore the PCI configuration space. The Open CISS
- * Specification says, "Restore the PCI Configuration
- * Registers, offsets 00h through 60h. It is important to
- * restore the command register, 16-bits at offset 04h,
- * last. Do not restore the configuration status register,
- * 16-bits at offset 06h." Note that the offset is 2*i.
- */
- for (i = 0; i < 32; i++) {
- if (i == 2 || i == 3)
- continue;
- pci_write_config_word(pdev, 2*i, saved_config_space[i]);
+ pci_restore_state(pdev);
+ rc = pci_enable_device(pdev);
+ if (rc) {
+ dev_warn(&pdev->dev, "failed to enable device.\n");
+ goto unmap_cfgtable;
}
- wmb();
- pci_write_config_word(pdev, 4, saved_config_space[2]);
+ pci_write_config_word(pdev, 4, command_register);
/* Some devices (notably the HP Smart Array 5i Controller)
need a little pause here */
@@ -3732,8 +3683,6 @@
return 0; /* just try to do the kdump anyhow. */
if (rc)
return -ENODEV;
- if (hpsa_reset_msi(pdev))
- return -ENODEV;
/* Now try to get the controller to respond to a no-op */
for (i = 0; i < HPSA_POST_RESET_NOOP_RETRIES; i++) {