m68knommu: platform support for i2c devices on ColdFire SoC
These changes based on work by Steven King <sfking@fdwdc.com> to support
the i2c hardware modules on ColdFire SoC family devices.
This is the per SoC hardware support. Contains a common platform device
setup. Each of the SoC family members tends to have some minor local
setup required to initialize the module. But all ColdFire family members
use the same i2c hardware module.
This i2c hardware module is the same as used in the Freescale iMX ARM
based family of SoC devices. Steven's original patches were based on using
a new and different i2c-coldfire.c driver. But this is not neccessary as
we can use the existing Linux i2c-imx.c driver with no change required to
it. And this patch is now based on using the existing i2c-imx driver.
This patch only contains the ColdFire platform changes.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Tested-by: Angelo Dureghello <angelo@sysam.it>
diff --git a/arch/m68k/coldfire/m53xx.c b/arch/m68k/coldfire/m53xx.c
index 2502f63..cf19179 100644
--- a/arch/m68k/coldfire/m53xx.c
+++ b/arch/m68k/coldfire/m53xx.c
@@ -38,7 +38,7 @@
DEFINE_CLK(0, "intc.0", 18, MCF_CLK);
DEFINE_CLK(0, "intc.1", 19, MCF_CLK);
DEFINE_CLK(0, "iack.0", 21, MCF_CLK);
-DEFINE_CLK(0, "mcfi2c.0", 22, MCF_CLK);
+DEFINE_CLK(0, "imx1-i2c.0", 22, MCF_CLK);
DEFINE_CLK(0, "mcfqspi.0", 23, MCF_CLK);
DEFINE_CLK(0, "mcfuart.0", 24, MCF_BUSCLK);
DEFINE_CLK(0, "mcfuart.1", 25, MCF_BUSCLK);
@@ -77,7 +77,7 @@
&__clk_0_18, /* intc.0 */
&__clk_0_19, /* intc.1 */
&__clk_0_21, /* iack.0 */
- &__clk_0_22, /* mcfi2c.0 */
+ &__clk_0_22, /* imx1-i2c.0 */
&__clk_0_23, /* mcfqspi.0 */
&__clk_0_24, /* mcfuart.0 */
&__clk_0_25, /* mcfuart.1 */
@@ -133,7 +133,7 @@
&__clk_0_8, /* mcfcan.0 */
&__clk_0_12, /* fec.0 */
&__clk_0_17, /* edma */
- &__clk_0_22, /* mcfi2c.0 */
+ &__clk_0_22, /* imx1-i2c.0 */
&__clk_0_23, /* mcfqspi.0 */
&__clk_0_30, /* mcftmr.2 */
&__clk_0_31, /* mcftmr.3 */
@@ -176,6 +176,19 @@
/***************************************************************************/
+static void __init m53xx_i2c_init(void)
+{
+#if IS_ENABLED(CONFIG_I2C_IMX)
+ /* setup Port AS Pin Assignment Register for I2C */
+ /* set PASPA0 to SCL and PASPA1 to SDA */
+ u8 r = readb(MCFGPIO_PAR_FECI2C);
+ r |= 0x0f;
+ writeb(r, MCFGPIO_PAR_FECI2C);
+#endif /* IS_ENABLED(CONFIG_I2C_IMX) */
+}
+
+/***************************************************************************/
+
static void __init m53xx_uarts_init(void)
{
/* UART GPIO initialization */
@@ -218,6 +231,7 @@
m53xx_uarts_init();
m53xx_fec_init();
m53xx_qspi_init();
+ m53xx_i2c_init();
#ifdef CONFIG_BDM_DISABLE
/*