| /* |
| * arch/ppc/platforms/4xx/ibmstb4.h |
| * |
| * Author: Armin Kuster <akuster@mvista.com> |
| * |
| * 2001 (c) MontaVista, Software, Inc. This file is licensed under |
| * the terms of the GNU General Public License version 2. This program |
| * is licensed "as is" without any warranty of any kind, whether express |
| * or implied. |
| */ |
| |
| #ifdef __KERNEL__ |
| #ifndef __ASM_IBMSTB4_H__ |
| #define __ASM_IBMSTB4_H__ |
| |
| #include <linux/config.h> |
| |
| /* serial port defines */ |
| #define STB04xxx_IO_BASE ((uint)0xe0000000) |
| #define PPC4xx_PCI_IO_ADDR STB04xxx_IO_BASE |
| #define PPC4xx_ONB_IO_PADDR STB04xxx_IO_BASE |
| #define PPC4xx_ONB_IO_VADDR ((uint)0xe0000000) |
| #define PPC4xx_ONB_IO_SIZE ((uint)14*64*1024) |
| |
| /* |
| * map STB04xxx internal i/o address (0x400x00xx) to an address |
| * which is below the 2GB limit... |
| * |
| * 4000 000x uart1 -> 0xe000 000x |
| * 4001 00xx ppu |
| * 4002 00xx smart card |
| * 4003 000x iic |
| * 4004 000x uart0 |
| * 4005 0xxx timer |
| * 4006 00xx gpio |
| * 4007 00xx smart card |
| * 400b 000x iic |
| * 400c 000x scp |
| * 400d 000x modem |
| * 400e 000x uart2 |
| */ |
| #define STB04xxx_MAP_IO_ADDR(a) (((uint)(a)) + (STB04xxx_IO_BASE - 0x40000000)) |
| |
| #define RS_TABLE_SIZE 3 |
| #define UART0_INT 20 |
| |
| #ifdef __BOOTER__ |
| #define UART0_IO_BASE 0x40040000 |
| #else |
| #define UART0_IO_BASE 0xe0040000 |
| #endif |
| |
| #define UART1_INT 21 |
| |
| #ifdef __BOOTER__ |
| #define UART1_IO_BASE 0x40000000 |
| #else |
| #define UART1_IO_BASE 0xe0000000 |
| #endif |
| |
| #define UART2_INT 31 |
| #ifdef __BOOTER__ |
| #define UART2_IO_BASE 0x400e0000 |
| #else |
| #define UART2_IO_BASE 0xe00e0000 |
| #endif |
| |
| #define IDE0_BASE 0x400F0000 |
| #define IDE0_SIZE 0x200 |
| #define IDE0_IRQ 25 |
| #define IIC0_BASE 0x40030000 |
| #define IIC1_BASE 0x400b0000 |
| #define OPB0_BASE 0x40000000 |
| #define GPIO0_BASE 0x40060000 |
| |
| #define USB0_BASE 0x40010000 |
| #define USB0_SIZE 0xA0 |
| #define USB0_IRQ 18 |
| |
| #define IIC_NUMS 2 |
| #define UART_NUMS 3 |
| #define IIC0_IRQ 9 |
| #define IIC1_IRQ 10 |
| #define IIC_OWN 0x55 |
| #define IIC_CLOCK 50 |
| |
| #define BD_EMAC_ADDR(e,i) bi_enetaddr[i] |
| |
| #define STD_UART_OP(num) \ |
| { 0, BASE_BAUD, 0, UART##num##_INT, \ |
| (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST), \ |
| iomem_base: (u8 *)UART##num##_IO_BASE, \ |
| io_type: SERIAL_IO_MEM}, |
| |
| #if defined(CONFIG_UART0_TTYS0) |
| #define SERIAL_DEBUG_IO_BASE UART0_IO_BASE |
| #define SERIAL_PORT_DFNS \ |
| STD_UART_OP(0) \ |
| STD_UART_OP(1) \ |
| STD_UART_OP(2) |
| #endif |
| |
| #if defined(CONFIG_UART0_TTYS1) |
| #define SERIAL_DEBUG_IO_BASE UART2_IO_BASE |
| #define SERIAL_PORT_DFNS \ |
| STD_UART_OP(1) \ |
| STD_UART_OP(0) \ |
| STD_UART_OP(2) |
| #endif |
| |
| #if defined(CONFIG_UART0_TTYS2) |
| #define SERIAL_DEBUG_IO_BASE UART2_IO_BASE |
| #define SERIAL_PORT_DFNS \ |
| STD_UART_OP(2) \ |
| STD_UART_OP(0) \ |
| STD_UART_OP(1) |
| #endif |
| |
| #define DCRN_BE_BASE 0x090 |
| #define DCRN_DMA0_BASE 0x0C0 |
| #define DCRN_DMA1_BASE 0x0C8 |
| #define DCRN_DMA2_BASE 0x0D0 |
| #define DCRN_DMA3_BASE 0x0D8 |
| #define DCRNCAP_DMA_CC 1 /* have DMA chained count capability */ |
| #define DCRN_DMASR_BASE 0x0E0 |
| #define DCRN_PLB0_BASE 0x054 |
| #define DCRN_PLB1_BASE 0x064 |
| #define DCRN_POB0_BASE 0x0B0 |
| #define DCRN_SCCR_BASE 0x120 |
| #define DCRN_UIC0_BASE 0x040 |
| #define DCRN_BE_BASE 0x090 |
| #define DCRN_DMA0_BASE 0x0C0 |
| #define DCRN_DMA1_BASE 0x0C8 |
| #define DCRN_DMA2_BASE 0x0D0 |
| #define DCRN_DMA3_BASE 0x0D8 |
| #define DCRN_CIC_BASE 0x030 |
| #define DCRN_DMASR_BASE 0x0E0 |
| #define DCRN_EBIMC_BASE 0x070 |
| #define DCRN_DCRX_BASE 0x020 |
| #define DCRN_CPMFR_BASE 0x102 |
| #define DCRN_SCCR_BASE 0x120 |
| #define UIC0 DCRN_UIC0_BASE |
| |
| #define IBM_CPM_IIC0 0x80000000 /* IIC 0 interface */ |
| #define IBM_CPM_USB0 0x40000000 /* IEEE-1284 */ |
| #define IBM_CPM_IIC1 0x20000000 /* IIC 1 interface */ |
| #define IBM_CPM_CPU 0x10000000 /* PPC405B3 clock control */ |
| #define IBM_CPM_AUD 0x08000000 /* Audio Decoder */ |
| #define IBM_CPM_EBIU 0x04000000 /* External Bus Interface Unit */ |
| #define IBM_CPM_SDRAM1 0x02000000 /* SDRAM 1 memory controller */ |
| #define IBM_CPM_DMA 0x01000000 /* DMA controller */ |
| #define IBM_CPM_DMA1 0x00800000 /* reserved */ |
| #define IBM_CPM_XPT1 0x00400000 /* reserved */ |
| #define IBM_CPM_XPT2 0x00200000 /* reserved */ |
| #define IBM_CPM_UART1 0x00100000 /* Serial 1 / Infrared */ |
| #define IBM_CPM_UART0 0x00080000 /* Serial 0 / 16550 */ |
| #define IBM_CPM_EPI 0x00040000 /* DCR Extension */ |
| #define IBM_CPM_SC0 0x00020000 /* Smart Card 0 */ |
| #define IBM_CPM_VID 0x00010000 /* reserved */ |
| #define IBM_CPM_SC1 0x00008000 /* Smart Card 1 */ |
| #define IBM_CPM_USBSDRA 0x00004000 /* SDRAM 0 memory controller */ |
| #define IBM_CPM_XPT0 0x00002000 /* Transport - 54 Mhz */ |
| #define IBM_CPM_CBS 0x00001000 /* Cross Bar Switch */ |
| #define IBM_CPM_GPT 0x00000800 /* GPTPWM */ |
| #define IBM_CPM_GPIO0 0x00000400 /* General Purpose IO 0 */ |
| #define IBM_CPM_DENC 0x00000200 /* Digital video Encoder */ |
| #define IBM_CPM_TMRCLK 0x00000100 /* CPU timers */ |
| #define IBM_CPM_XPT27 0x00000080 /* Transport - 27 Mhz */ |
| #define IBM_CPM_UIC 0x00000040 /* Universal Interrupt Controller */ |
| #define IBM_CPM_SSP 0x00000010 /* Modem Serial Interface (SSP) */ |
| #define IBM_CPM_UART2 0x00000008 /* Serial Control Port */ |
| #define IBM_CPM_DDIO 0x00000004 /* Descrambler */ |
| #define IBM_CPM_VID2 0x00000002 /* Video Decoder clock domain 2 */ |
| |
| #define DFLT_IBM4xx_PM ~(IBM_CPM_CPU | IBM_CPM_EBIU | IBM_CPM_SDRAM1 \ |
| | IBM_CPM_DMA | IBM_CPM_DMA1 | IBM_CPM_CBS \ |
| | IBM_CPM_USBSDRA | IBM_CPM_XPT0 | IBM_CPM_TMRCLK \ |
| | IBM_CPM_XPT27 | IBM_CPM_UIC ) |
| |
| #define DCRN_BEAR (DCRN_BE_BASE + 0x0) /* Bus Error Address Register */ |
| #define DCRN_BESR (DCRN_BE_BASE + 0x1) /* Bus Error Syndrome Register */ |
| /* DCRN_BESR */ |
| #define BESR_DSES 0x80000000 /* Data-Side Error Status */ |
| #define BESR_DMES 0x40000000 /* DMA Error Status */ |
| #define BESR_RWS 0x20000000 /* Read/Write Status */ |
| #define BESR_ETMASK 0x1C000000 /* Error Type */ |
| #define ET_PROT 0 |
| #define ET_PARITY 1 |
| #define ET_NCFG 2 |
| #define ET_BUSERR 4 |
| #define ET_BUSTO 6 |
| |
| #define CHR1_CETE 0x00800000 /* CPU external timer enable */ |
| #define CHR1_PCIPW 0x00008000 /* PCI Int enable/Peripheral Write enable */ |
| |
| #define DCRN_CICCR (DCRN_CIC_BASE + 0x0) /* CIC Control Register */ |
| #define DCRN_DMAS1 (DCRN_CIC_BASE + 0x1) /* DMA Select1 Register */ |
| #define DCRN_DMAS2 (DCRN_CIC_BASE + 0x2) /* DMA Select2 Register */ |
| #define DCRN_CICVCR (DCRN_CIC_BASE + 0x3) /* CIC Video COntro Register */ |
| #define DCRN_CICSEL3 (DCRN_CIC_BASE + 0x5) /* CIC Select 3 Register */ |
| #define DCRN_SGPO (DCRN_CIC_BASE + 0x6) /* CIC GPIO Output Register */ |
| #define DCRN_SGPOD (DCRN_CIC_BASE + 0x7) /* CIC GPIO OD Register */ |
| #define DCRN_SGPTC (DCRN_CIC_BASE + 0x8) /* CIC GPIO Tristate Ctrl Reg */ |
| #define DCRN_SGPI (DCRN_CIC_BASE + 0x9) /* CIC GPIO Input Reg */ |
| |
| #define DCRN_DCRXICR (DCRN_DCRX_BASE + 0x0) /* Internal Control Register */ |
| #define DCRN_DCRXISR (DCRN_DCRX_BASE + 0x1) /* Internal Status Register */ |
| #define DCRN_DCRXECR (DCRN_DCRX_BASE + 0x2) /* External Control Register */ |
| #define DCRN_DCRXESR (DCRN_DCRX_BASE + 0x3) /* External Status Register */ |
| #define DCRN_DCRXTAR (DCRN_DCRX_BASE + 0x4) /* Target Address Register */ |
| #define DCRN_DCRXTDR (DCRN_DCRX_BASE + 0x5) /* Target Data Register */ |
| #define DCRN_DCRXIGR (DCRN_DCRX_BASE + 0x6) /* Interrupt Generation Register */ |
| #define DCRN_DCRXBCR (DCRN_DCRX_BASE + 0x7) /* Line Buffer Control Register */ |
| |
| #define DCRN_BRCRH0 (DCRN_EBIMC_BASE + 0x0) /* Bus Region Config High 0 */ |
| #define DCRN_BRCRH1 (DCRN_EBIMC_BASE + 0x1) /* Bus Region Config High 1 */ |
| #define DCRN_BRCRH2 (DCRN_EBIMC_BASE + 0x2) /* Bus Region Config High 2 */ |
| #define DCRN_BRCRH3 (DCRN_EBIMC_BASE + 0x3) /* Bus Region Config High 3 */ |
| #define DCRN_BRCRH4 (DCRN_EBIMC_BASE + 0x4) /* Bus Region Config High 4 */ |
| #define DCRN_BRCRH5 (DCRN_EBIMC_BASE + 0x5) /* Bus Region Config High 5 */ |
| #define DCRN_BRCRH6 (DCRN_EBIMC_BASE + 0x6) /* Bus Region Config High 6 */ |
| #define DCRN_BRCRH7 (DCRN_EBIMC_BASE + 0x7) /* Bus Region Config High 7 */ |
| #define DCRN_BRCR0 (DCRN_EBIMC_BASE + 0x10) /* BRC 0 */ |
| #define DCRN_BRCR1 (DCRN_EBIMC_BASE + 0x11) /* BRC 1 */ |
| #define DCRN_BRCR2 (DCRN_EBIMC_BASE + 0x12) /* BRC 2 */ |
| #define DCRN_BRCR3 (DCRN_EBIMC_BASE + 0x13) /* BRC 3 */ |
| #define DCRN_BRCR4 (DCRN_EBIMC_BASE + 0x14) /* BRC 4 */ |
| #define DCRN_BRCR5 (DCRN_EBIMC_BASE + 0x15) /* BRC 5 */ |
| #define DCRN_BRCR6 (DCRN_EBIMC_BASE + 0x16) /* BRC 6 */ |
| #define DCRN_BRCR7 (DCRN_EBIMC_BASE + 0x17) /* BRC 7 */ |
| #define DCRN_BEAR0 (DCRN_EBIMC_BASE + 0x20) /* Bus Error Address Register */ |
| #define DCRN_BESR0 (DCRN_EBIMC_BASE + 0x21) /* Bus Error Status Register */ |
| #define DCRN_BIUCR (DCRN_EBIMC_BASE + 0x2A) /* Bus Interfac Unit Ctrl Reg */ |
| |
| #include <asm/ibm405.h> |
| |
| #endif /* __ASM_IBMSTB4_H__ */ |
| #endif /* __KERNEL__ */ |