irqchip: crossbar: Introduce ti, max-crossbar-sources to identify valid crossbar mapping
Currently we attempt to map any crossbar value to an IRQ, however,
this is not correct from hardware perspective. There is a max crossbar
event number upto which hardware supports. So describe the same in
device tree using 'ti,max-crossbar-sources' property and use it to
validate requests.
[ jac - remove MAX_SOURCES from binding doc, use integer because we
shouldn't put implementation details in the binding docs ]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-14-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
diff --git a/Documentation/devicetree/bindings/arm/omap/crossbar.txt b/Documentation/devicetree/bindings/arm/omap/crossbar.txt
index 5f45c78..a6e462f 100644
--- a/Documentation/devicetree/bindings/arm/omap/crossbar.txt
+++ b/Documentation/devicetree/bindings/arm/omap/crossbar.txt
@@ -10,6 +10,7 @@
- compatible : Should be "ti,irq-crossbar"
- reg: Base address and the size of the crossbar registers.
- ti,max-irqs: Total number of irqs available at the interrupt controller.
+- ti,max-crossbar-sources: Maximum number of crossbar sources that can be routed.
- ti,reg-size: Size of a individual register in bytes. Every individual
register is assumed to be of same size. Valid sizes are 1, 2, 4.
- ti,irqs-reserved: List of the reserved irq lines that are not muxed using
@@ -30,6 +31,7 @@
compatible = "ti,irq-crossbar";
reg = <0x4a002a48 0x130>;
ti,max-irqs = <160>;
+ ti,max-crossbar-sources = <400>;
ti,reg-size = <2>;
ti,irqs-reserved = <0 1 2 3 5 6 131 132 139 140>;
ti,irqs-skip = <10 133 139 140>;
diff --git a/drivers/irqchip/irq-crossbar.c b/drivers/irqchip/irq-crossbar.c
index 518d712..c9f068c 100644
--- a/drivers/irqchip/irq-crossbar.c
+++ b/drivers/irqchip/irq-crossbar.c
@@ -26,6 +26,7 @@
* struct crossbar_device - crossbar device description
* @int_max: maximum number of supported interrupts
* @safe_map: safe default value to initialize the crossbar
+ * @max_crossbar_sources: Maximum number of crossbar sources
* @irq_map: array of interrupts to crossbar number mapping
* @crossbar_base: crossbar base address
* @register_offsets: offsets for each irq number
@@ -34,6 +35,7 @@
struct crossbar_device {
uint int_max;
uint safe_map;
+ uint max_crossbar_sources;
uint *irq_map;
void __iomem *crossbar_base;
int *register_offsets;
@@ -117,12 +119,19 @@
unsigned int *out_type)
{
int ret;
+ int req_num = intspec[1];
- ret = get_prev_map_irq(intspec[1]);
+ if (req_num >= cb->max_crossbar_sources) {
+ pr_err("%s: requested crossbar number %d > max %d\n",
+ __func__, req_num, cb->max_crossbar_sources);
+ return -EINVAL;
+ }
+
+ ret = get_prev_map_irq(req_num);
if (ret >= 0)
goto found;
- ret = allocate_free_irq(intspec[1]);
+ ret = allocate_free_irq(req_num);
if (ret < 0)
return ret;
@@ -153,6 +162,14 @@
if (!cb->crossbar_base)
goto err_cb;
+ of_property_read_u32(node, "ti,max-crossbar-sources",
+ &cb->max_crossbar_sources);
+ if (!cb->max_crossbar_sources) {
+ pr_err("missing 'ti,max-crossbar-sources' property\n");
+ ret = -EINVAL;
+ goto err_base;
+ }
+
of_property_read_u32(node, "ti,max-irqs", &max);
if (!max) {
pr_err("missing 'ti,max-irqs' property\n");