| /* |
| * Copyright 2012 Sascha Hauer, Pengutronix |
| * |
| * The code contained herein is licensed under the GNU General Public |
| * License. You may obtain a copy of the GNU General Public License |
| * Version 2 or later at the following locations: |
| * |
| * http://www.opensource.org/licenses/gpl-license.html |
| * http://www.gnu.org/copyleft/gpl.html |
| */ |
| |
| #include "skeleton.dtsi" |
| |
| / { |
| aliases { |
| gpio0 = &gpio1; |
| gpio1 = &gpio2; |
| gpio2 = &gpio3; |
| gpio3 = &gpio4; |
| gpio4 = &gpio5; |
| gpio5 = &gpio6; |
| i2c0 = &i2c1; |
| i2c1 = &i2c2; |
| serial0 = &uart1; |
| serial1 = &uart2; |
| serial2 = &uart3; |
| serial3 = &uart4; |
| serial4 = &uart5; |
| serial5 = &uart6; |
| spi0 = &cspi1; |
| spi1 = &cspi2; |
| spi2 = &cspi3; |
| }; |
| |
| aitc: aitc-interrupt-controller@e0000000 { |
| compatible = "fsl,imx27-aitc", "fsl,avic"; |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| reg = <0x10040000 0x1000>; |
| }; |
| |
| clocks { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| osc26m { |
| compatible = "fsl,imx-osc26m", "fixed-clock"; |
| clock-frequency = <26000000>; |
| }; |
| }; |
| |
| cpus { |
| #size-cells = <0>; |
| #address-cells = <1>; |
| |
| cpu: cpu@0 { |
| device_type = "cpu"; |
| compatible = "arm,arm926ej-s"; |
| operating-points = < |
| /* kHz uV */ |
| 266000 1300000 |
| 399000 1450000 |
| >; |
| clock-latency = <62500>; |
| clocks = <&clks 18>; |
| voltage-tolerance = <5>; |
| }; |
| }; |
| |
| soc { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "simple-bus"; |
| interrupt-parent = <&aitc>; |
| ranges; |
| |
| aipi@10000000 { /* AIPI1 */ |
| compatible = "fsl,aipi-bus", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x10000000 0x20000>; |
| ranges; |
| |
| dma: dma@10001000 { |
| compatible = "fsl,imx27-dma"; |
| reg = <0x10001000 0x1000>; |
| interrupts = <32>; |
| clocks = <&clks 50>, <&clks 70>; |
| clock-names = "ipg", "ahb"; |
| #dma-cells = <1>; |
| #dma-channels = <16>; |
| }; |
| |
| wdog: wdog@10002000 { |
| compatible = "fsl,imx27-wdt", "fsl,imx21-wdt"; |
| reg = <0x10002000 0x1000>; |
| interrupts = <27>; |
| clocks = <&clks 74>; |
| }; |
| |
| gpt1: timer@10003000 { |
| compatible = "fsl,imx27-gpt", "fsl,imx1-gpt"; |
| reg = <0x10003000 0x1000>; |
| interrupts = <26>; |
| clocks = <&clks 46>, <&clks 61>; |
| clock-names = "ipg", "per"; |
| }; |
| |
| gpt2: timer@10004000 { |
| compatible = "fsl,imx27-gpt", "fsl,imx1-gpt"; |
| reg = <0x10004000 0x1000>; |
| interrupts = <25>; |
| clocks = <&clks 45>, <&clks 61>; |
| clock-names = "ipg", "per"; |
| }; |
| |
| gpt3: timer@10005000 { |
| compatible = "fsl,imx27-gpt", "fsl,imx1-gpt"; |
| reg = <0x10005000 0x1000>; |
| interrupts = <24>; |
| clocks = <&clks 44>, <&clks 61>; |
| clock-names = "ipg", "per"; |
| }; |
| |
| pwm: pwm@10006000 { |
| compatible = "fsl,imx27-pwm"; |
| reg = <0x10006000 0x1000>; |
| interrupts = <23>; |
| clocks = <&clks 34>, <&clks 61>; |
| clock-names = "ipg", "per"; |
| }; |
| |
| kpp: kpp@10008000 { |
| compatible = "fsl,imx27-kpp", "fsl,imx21-kpp"; |
| reg = <0x10008000 0x1000>; |
| interrupts = <21>; |
| clocks = <&clks 37>; |
| status = "disabled"; |
| }; |
| |
| owire: owire@10009000 { |
| compatible = "fsl,imx27-owire", "fsl,imx21-owire"; |
| reg = <0x10009000 0x1000>; |
| clocks = <&clks 35>; |
| status = "disabled"; |
| }; |
| |
| uart1: serial@1000a000 { |
| compatible = "fsl,imx27-uart", "fsl,imx21-uart"; |
| reg = <0x1000a000 0x1000>; |
| interrupts = <20>; |
| clocks = <&clks 81>, <&clks 61>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| uart2: serial@1000b000 { |
| compatible = "fsl,imx27-uart", "fsl,imx21-uart"; |
| reg = <0x1000b000 0x1000>; |
| interrupts = <19>; |
| clocks = <&clks 80>, <&clks 61>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| uart3: serial@1000c000 { |
| compatible = "fsl,imx27-uart", "fsl,imx21-uart"; |
| reg = <0x1000c000 0x1000>; |
| interrupts = <18>; |
| clocks = <&clks 79>, <&clks 61>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| uart4: serial@1000d000 { |
| compatible = "fsl,imx27-uart", "fsl,imx21-uart"; |
| reg = <0x1000d000 0x1000>; |
| interrupts = <17>; |
| clocks = <&clks 78>, <&clks 61>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| cspi1: cspi@1000e000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx27-cspi"; |
| reg = <0x1000e000 0x1000>; |
| interrupts = <16>; |
| clocks = <&clks 53>, <&clks 60>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| cspi2: cspi@1000f000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx27-cspi"; |
| reg = <0x1000f000 0x1000>; |
| interrupts = <15>; |
| clocks = <&clks 52>, <&clks 60>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| i2c1: i2c@10012000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx27-i2c", "fsl,imx21-i2c"; |
| reg = <0x10012000 0x1000>; |
| interrupts = <12>; |
| clocks = <&clks 40>; |
| status = "disabled"; |
| }; |
| |
| sdhci1: sdhci@10013000 { |
| compatible = "fsl,imx27-mmc", "fsl,imx21-mmc"; |
| reg = <0x10013000 0x1000>; |
| interrupts = <11>; |
| clocks = <&clks 30>, <&clks 60>; |
| clock-names = "ipg", "per"; |
| dmas = <&dma 7>; |
| dma-names = "rx-tx"; |
| status = "disabled"; |
| }; |
| |
| sdhci2: sdhci@10014000 { |
| compatible = "fsl,imx27-mmc", "fsl,imx21-mmc"; |
| reg = <0x10014000 0x1000>; |
| interrupts = <10>; |
| clocks = <&clks 29>, <&clks 60>; |
| clock-names = "ipg", "per"; |
| dmas = <&dma 6>; |
| dma-names = "rx-tx"; |
| status = "disabled"; |
| }; |
| |
| gpio1: gpio@10015000 { |
| compatible = "fsl,imx27-gpio", "fsl,imx21-gpio"; |
| reg = <0x10015000 0x100>; |
| interrupts = <8>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio2: gpio@10015100 { |
| compatible = "fsl,imx27-gpio", "fsl,imx21-gpio"; |
| reg = <0x10015100 0x100>; |
| interrupts = <8>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio3: gpio@10015200 { |
| compatible = "fsl,imx27-gpio", "fsl,imx21-gpio"; |
| reg = <0x10015200 0x100>; |
| interrupts = <8>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio4: gpio@10015300 { |
| compatible = "fsl,imx27-gpio", "fsl,imx21-gpio"; |
| reg = <0x10015300 0x100>; |
| interrupts = <8>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio5: gpio@10015400 { |
| compatible = "fsl,imx27-gpio", "fsl,imx21-gpio"; |
| reg = <0x10015400 0x100>; |
| interrupts = <8>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio6: gpio@10015500 { |
| compatible = "fsl,imx27-gpio", "fsl,imx21-gpio"; |
| reg = <0x10015500 0x100>; |
| interrupts = <8>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| audmux: audmux@10016000 { |
| compatible = "fsl,imx27-audmux", "fsl,imx21-audmux"; |
| reg = <0x10016000 0x1000>; |
| clocks = <&clks 0>; |
| clock-names = "audmux"; |
| status = "disabled"; |
| }; |
| |
| cspi3: cspi@10017000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx27-cspi"; |
| reg = <0x10017000 0x1000>; |
| interrupts = <6>; |
| clocks = <&clks 51>, <&clks 60>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| gpt4: timer@10019000 { |
| compatible = "fsl,imx27-gpt", "fsl,imx1-gpt"; |
| reg = <0x10019000 0x1000>; |
| interrupts = <4>; |
| clocks = <&clks 43>, <&clks 61>; |
| clock-names = "ipg", "per"; |
| }; |
| |
| gpt5: timer@1001a000 { |
| compatible = "fsl,imx27-gpt", "fsl,imx1-gpt"; |
| reg = <0x1001a000 0x1000>; |
| interrupts = <3>; |
| clocks = <&clks 42>, <&clks 61>; |
| clock-names = "ipg", "per"; |
| }; |
| |
| uart5: serial@1001b000 { |
| compatible = "fsl,imx27-uart", "fsl,imx21-uart"; |
| reg = <0x1001b000 0x1000>; |
| interrupts = <49>; |
| clocks = <&clks 77>, <&clks 61>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| uart6: serial@1001c000 { |
| compatible = "fsl,imx27-uart", "fsl,imx21-uart"; |
| reg = <0x1001c000 0x1000>; |
| interrupts = <48>; |
| clocks = <&clks 78>, <&clks 61>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| i2c2: i2c@1001d000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx27-i2c", "fsl,imx21-i2c"; |
| reg = <0x1001d000 0x1000>; |
| interrupts = <1>; |
| clocks = <&clks 39>; |
| status = "disabled"; |
| }; |
| |
| sdhci3: sdhci@1001e000 { |
| compatible = "fsl,imx27-mmc", "fsl,imx21-mmc"; |
| reg = <0x1001e000 0x1000>; |
| interrupts = <9>; |
| clocks = <&clks 28>, <&clks 60>; |
| clock-names = "ipg", "per"; |
| dmas = <&dma 36>; |
| dma-names = "rx-tx"; |
| status = "disabled"; |
| }; |
| |
| gpt6: timer@1001f000 { |
| compatible = "fsl,imx27-gpt", "fsl,imx1-gpt"; |
| reg = <0x1001f000 0x1000>; |
| interrupts = <2>; |
| clocks = <&clks 41>, <&clks 61>; |
| clock-names = "ipg", "per"; |
| }; |
| }; |
| |
| aipi@10020000 { /* AIPI2 */ |
| compatible = "fsl,aipi-bus", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x10020000 0x20000>; |
| ranges; |
| |
| fb: fb@10021000 { |
| compatible = "fsl,imx27-fb", "fsl,imx21-fb"; |
| interrupts = <61>; |
| reg = <0x10021000 0x1000>; |
| clocks = <&clks 36>, <&clks 65>, <&clks 59>; |
| clock-names = "ipg", "ahb", "per"; |
| status = "disabled"; |
| }; |
| |
| coda: coda@10023000 { |
| compatible = "fsl,imx27-vpu"; |
| reg = <0x10023000 0x0200>; |
| interrupts = <53>; |
| clocks = <&clks 57>, <&clks 66>; |
| clock-names = "per", "ahb"; |
| iram = <&iram>; |
| }; |
| |
| sahara2: sahara@10025000 { |
| compatible = "fsl,imx27-sahara"; |
| reg = <0x10025000 0x1000>; |
| interrupts = <59>; |
| clocks = <&clks 32>, <&clks 64>; |
| clock-names = "ipg", "ahb"; |
| }; |
| |
| clks: ccm@10027000{ |
| compatible = "fsl,imx27-ccm"; |
| reg = <0x10027000 0x1000>; |
| #clock-cells = <1>; |
| }; |
| |
| iim: iim@10028000 { |
| compatible = "fsl,imx27-iim"; |
| reg = <0x10028000 0x1000>; |
| interrupts = <62>; |
| clocks = <&clks 38>; |
| }; |
| |
| fec: ethernet@1002b000 { |
| compatible = "fsl,imx27-fec"; |
| reg = <0x1002b000 0x4000>; |
| interrupts = <50>; |
| clocks = <&clks 48>, <&clks 67>; |
| clock-names = "ipg", "ahb"; |
| status = "disabled"; |
| }; |
| }; |
| |
| nfc: nand@d8000000 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "fsl,imx27-nand"; |
| reg = <0xd8000000 0x1000>; |
| interrupts = <29>; |
| clocks = <&clks 54>; |
| status = "disabled"; |
| }; |
| |
| weim: weim@d8002000 { |
| #address-cells = <2>; |
| #size-cells = <1>; |
| compatible = "fsl,imx27-weim"; |
| reg = <0xd8002000 0x1000>; |
| clocks = <&clks 0>; |
| ranges = < |
| 0 0 0xc0000000 0x08000000 |
| 1 0 0xc8000000 0x08000000 |
| 2 0 0xd0000000 0x02000000 |
| 3 0 0xd2000000 0x02000000 |
| 4 0 0xd4000000 0x02000000 |
| 5 0 0xd6000000 0x02000000 |
| >; |
| status = "disabled"; |
| }; |
| |
| iram: iram@ffff4c00 { |
| compatible = "mmio-sram"; |
| reg = <0xffff4c00 0xb400>; |
| }; |
| }; |
| }; |