| /* |
| * w83795.c - Linux kernel driver for hardware monitoring |
| * Copyright (C) 2008 Nuvoton Technology Corp. |
| * Wei Song |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation - version 2. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA |
| * 02110-1301 USA. |
| * |
| * Supports following chips: |
| * |
| * Chip #vin #fanin #pwm #temp #dts wchipid vendid i2c ISA |
| * w83795g 21 14 8 6 8 0x79 0x5ca3 yes no |
| * w83795adg 18 14 2 6 8 0x79 0x5ca3 yes no |
| */ |
| |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/init.h> |
| #include <linux/slab.h> |
| #include <linux/i2c.h> |
| #include <linux/hwmon.h> |
| #include <linux/hwmon-sysfs.h> |
| #include <linux/err.h> |
| #include <linux/mutex.h> |
| #include <linux/delay.h> |
| |
| /* Addresses to scan */ |
| static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f, I2C_CLIENT_END }; |
| |
| enum chips { w83795 }; |
| |
| |
| static int reset; |
| module_param(reset, bool, 0); |
| MODULE_PARM_DESC(reset, "Set to 1 to reset chip, not recommended"); |
| |
| |
| #define W83795_REG_BANKSEL 0x00 |
| #define W83795_REG_VENDORID 0xfd |
| #define W83795_REG_CHIPID 0xfe |
| #define W83795_REG_DEVICEID 0xfb |
| |
| #define W83795_REG_I2C_ADDR 0xfc |
| #define W83795_REG_CONFIG 0x01 |
| #define W83795_REG_CONFIG_CONFIG48 0x04 |
| |
| /* Multi-Function Pin Ctrl Registers */ |
| #define W83795_REG_VOLT_CTRL1 0x02 |
| #define W83795_REG_VOLT_CTRL2 0x03 |
| #define W83795_REG_TEMP_CTRL1 0x04 |
| #define W83795_REG_TEMP_CTRL2 0x05 |
| #define W83795_REG_FANIN_CTRL1 0x06 |
| #define W83795_REG_FANIN_CTRL2 0x07 |
| #define W83795_REG_VMIGB_CTRL 0x08 |
| |
| #define TEMP_CTRL_DISABLE 0 |
| #define TEMP_CTRL_TD 1 |
| #define TEMP_CTRL_VSEN 2 |
| #define TEMP_CTRL_TR 3 |
| #define TEMP_CTRL_SHIFT 4 |
| #define TEMP_CTRL_HASIN_SHIFT 5 |
| /* temp mode may effect VSEN17-12 (in20-15) */ |
| static u16 W83795_REG_TEMP_CTRL[][6] = { |
| /* Disable, TD, VSEN, TR, register shift value, has_in shift num */ |
| {0x00, 0x01, 0x02, 0x03, 0, 17}, /* TR1 */ |
| {0x00, 0x04, 0x08, 0x0C, 2, 18}, /* TR2 */ |
| {0x00, 0x10, 0x20, 0x30, 4, 19}, /* TR3 */ |
| {0x00, 0x40, 0x80, 0xC0, 6, 20}, /* TR4 */ |
| {0x00, 0x00, 0x02, 0x03, 0, 15}, /* TR5 */ |
| {0x00, 0x00, 0x08, 0x0C, 2, 16}, /* TR6 */ |
| }; |
| |
| #define TEMP_READ 0 |
| #define TEMP_CRIT 1 |
| #define TEMP_CRIT_HYST 2 |
| #define TEMP_WARN 3 |
| #define TEMP_WARN_HYST 4 |
| /* only crit and crit_hyst affect real-time alarm status |
| * current crit crit_hyst warn warn_hyst */ |
| static u16 W83795_REG_TEMP[][5] = { |
| {0x21, 0x96, 0x97, 0x98, 0x99}, /* TD1/TR1 */ |
| {0x22, 0x9a, 0x9b, 0x9c, 0x9d}, /* TD2/TR2 */ |
| {0x23, 0x9e, 0x9f, 0xa0, 0xa1}, /* TD3/TR3 */ |
| {0x24, 0xa2, 0xa3, 0xa4, 0xa5}, /* TD4/TR4 */ |
| {0x1f, 0xa6, 0xa7, 0xa8, 0xa9}, /* TR5 */ |
| {0x20, 0xaa, 0xab, 0xac, 0xad}, /* TR6 */ |
| }; |
| |
| #define IN_READ 0 |
| #define IN_MAX 1 |
| #define IN_LOW 2 |
| static const u16 W83795_REG_IN[][3] = { |
| /* Current, HL, LL */ |
| {0x10, 0x70, 0x71}, /* VSEN1 */ |
| {0x11, 0x72, 0x73}, /* VSEN2 */ |
| {0x12, 0x74, 0x75}, /* VSEN3 */ |
| {0x13, 0x76, 0x77}, /* VSEN4 */ |
| {0x14, 0x78, 0x79}, /* VSEN5 */ |
| {0x15, 0x7a, 0x7b}, /* VSEN6 */ |
| {0x16, 0x7c, 0x7d}, /* VSEN7 */ |
| {0x17, 0x7e, 0x7f}, /* VSEN8 */ |
| {0x18, 0x80, 0x81}, /* VSEN9 */ |
| {0x19, 0x82, 0x83}, /* VSEN10 */ |
| {0x1A, 0x84, 0x85}, /* VSEN11 */ |
| {0x1B, 0x86, 0x87}, /* VTT */ |
| {0x1C, 0x88, 0x89}, /* 3VDD */ |
| {0x1D, 0x8a, 0x8b}, /* 3VSB */ |
| {0x1E, 0x8c, 0x8d}, /* VBAT */ |
| {0x1F, 0xa6, 0xa7}, /* VSEN12 */ |
| {0x20, 0xaa, 0xab}, /* VSEN13 */ |
| {0x21, 0x96, 0x97}, /* VSEN14 */ |
| {0x22, 0x9a, 0x9b}, /* VSEN15 */ |
| {0x23, 0x9e, 0x9f}, /* VSEN16 */ |
| {0x24, 0xa2, 0xa3}, /* VSEN17 */ |
| }; |
| #define W83795_REG_VRLSB 0x3C |
| #define VRLSB_SHIFT 6 |
| |
| static const u8 W83795_REG_IN_HL_LSB[] = { |
| 0x8e, /* VSEN1-4 */ |
| 0x90, /* VSEN5-8 */ |
| 0x92, /* VSEN9-11 */ |
| 0x94, /* VTT, 3VDD, 3VSB, 3VBAT */ |
| 0xa8, /* VSEN12 */ |
| 0xac, /* VSEN13 */ |
| 0x98, /* VSEN14 */ |
| 0x9c, /* VSEN15 */ |
| 0xa0, /* VSEN16 */ |
| 0xa4, /* VSEN17 */ |
| }; |
| |
| #define IN_LSB_REG(index, type) \ |
| (((type) == 1) ? W83795_REG_IN_HL_LSB[(index)] \ |
| : (W83795_REG_IN_HL_LSB[(index)] + 1)) |
| |
| #define IN_LSB_REG_NUM 10 |
| |
| #define IN_LSB_SHIFT 0 |
| #define IN_LSB_IDX 1 |
| static const u8 IN_LSB_SHIFT_IDX[][2] = { |
| /* High/Low LSB shift, LSB No. */ |
| {0x00, 0x00}, /* VSEN1 */ |
| {0x02, 0x00}, /* VSEN2 */ |
| {0x04, 0x00}, /* VSEN3 */ |
| {0x06, 0x00}, /* VSEN4 */ |
| {0x00, 0x01}, /* VSEN5 */ |
| {0x02, 0x01}, /* VSEN6 */ |
| {0x04, 0x01}, /* VSEN7 */ |
| {0x06, 0x01}, /* VSEN8 */ |
| {0x00, 0x02}, /* VSEN9 */ |
| {0x02, 0x02}, /* VSEN10 */ |
| {0x04, 0x02}, /* VSEN11 */ |
| {0x00, 0x03}, /* VTT */ |
| {0x02, 0x03}, /* 3VDD */ |
| {0x04, 0x03}, /* 3VSB */ |
| {0x06, 0x03}, /* VBAT */ |
| {0x06, 0x04}, /* VSEN12 */ |
| {0x06, 0x05}, /* VSEN13 */ |
| {0x06, 0x06}, /* VSEN14 */ |
| {0x06, 0x07}, /* VSEN15 */ |
| {0x06, 0x08}, /* VSEN16 */ |
| {0x06, 0x09}, /* VSEN17 */ |
| }; |
| |
| |
| /* 3VDD, 3VSB, VBAT * 0.006 */ |
| #define REST_VLT_BEGIN 12 /* the 13th volt to 15th */ |
| #define REST_VLT_END 14 /* the 13th volt to 15th */ |
| |
| #define W83795_REG_FAN(index) (0x2E + (index)) |
| #define W83795_REG_FAN_MIN_HL(index) (0xB6 + (index)) |
| #define W83795_REG_FAN_MIN_LSB(index) (0xC4 + (index) / 2) |
| #define W83795_REG_FAN_MIN_LSB_SHIFT(index) \ |
| (((index) % 1) ? 4 : 0) |
| |
| #define W83795_REG_VID_CTRL 0x6A |
| |
| #define ALARM_BEEP_REG_NUM 6 |
| #define W83795_REG_ALARM(index) (0x41 + (index)) |
| #define W83795_REG_BEEP(index) (0x50 + (index)) |
| |
| #define W83795_REG_CLR_CHASSIS 0x4D |
| |
| |
| #define W83795_REG_TEMP_NUM 6 |
| #define W83795_REG_FCMS1 0x201 |
| #define W83795_REG_FCMS2 0x208 |
| #define W83795_REG_TFMR(index) (0x202 + (index)) |
| #define W83795_REG_FOMC 0x20F |
| #define W83795_REG_FOPFP(index) (0x218 + (index)) |
| |
| #define W83795_REG_TSS(index) (0x209 + (index)) |
| |
| #define PWM_OUTPUT 0 |
| #define PWM_START 1 |
| #define PWM_NONSTOP 2 |
| #define PWM_STOP_TIME 3 |
| #define PWM_DIV 4 |
| #define W83795_REG_PWM(index, nr) \ |
| (((nr) == 0 ? 0x210 : \ |
| (nr) == 1 ? 0x220 : \ |
| (nr) == 2 ? 0x228 : \ |
| (nr) == 3 ? 0x230 : 0x218) + (index)) |
| |
| #define W83795_REG_FOPFP_DIV(index) \ |
| (((index) < 8) ? ((index) + 1) : \ |
| ((index) == 8) ? 12 : \ |
| (16 << ((index) - 9))) |
| |
| #define W83795_REG_FTSH(index) (0x240 + (index) * 2) |
| #define W83795_REG_FTSL(index) (0x241 + (index) * 2) |
| #define W83795_REG_TFTS 0x250 |
| |
| #define TEMP_PWM_TTTI 0 |
| #define TEMP_PWM_CTFS 1 |
| #define TEMP_PWM_HCT 2 |
| #define TEMP_PWM_HOT 3 |
| #define W83795_REG_TTTI(index) (0x260 + (index)) |
| #define W83795_REG_CTFS(index) (0x268 + (index)) |
| #define W83795_REG_HT(index) (0x270 + (index)) |
| |
| #define SF4_TEMP 0 |
| #define SF4_PWM 1 |
| #define W83795_REG_SF4_TEMP(temp_num, index) \ |
| (0x280 + 0x10 * (temp_num) + (index)) |
| #define W83795_REG_SF4_PWM(temp_num, index) \ |
| (0x288 + 0x10 * (temp_num) + (index)) |
| |
| #define W83795_REG_DTSC 0x301 |
| #define W83795_REG_DTSE 0x302 |
| #define W83795_REG_DTS(index) (0x26 + (index)) |
| |
| #define DTS_CRIT 0 |
| #define DTS_CRIT_HYST 1 |
| #define DTS_WARN 2 |
| #define DTS_WARN_HYST 3 |
| #define W83795_REG_DTS_EXT(index) (0xB2 + (index)) |
| |
| #define SETUP_PWM_DEFAULT 0 |
| #define SETUP_PWM_UPTIME 1 |
| #define SETUP_PWM_DOWNTIME 2 |
| #define W83795_REG_SETUP_PWM(index) (0x20C + (index)) |
| |
| static inline u16 in_from_reg(u8 index, u16 val) |
| { |
| if ((index >= REST_VLT_BEGIN) && (index <= REST_VLT_END)) |
| return val * 6; |
| else |
| return val * 2; |
| } |
| |
| static inline u16 in_to_reg(u8 index, u16 val) |
| { |
| if ((index >= REST_VLT_BEGIN) && (index <= REST_VLT_END)) |
| return val / 6; |
| else |
| return val / 2; |
| } |
| |
| static inline unsigned long fan_from_reg(u16 val) |
| { |
| if ((val >= 0xff0) || (val == 0)) |
| return 0; |
| return 1350000UL / val; |
| } |
| |
| static inline u16 fan_to_reg(long rpm) |
| { |
| if (rpm <= 0) |
| return 0x0fff; |
| return SENSORS_LIMIT((1350000 + (rpm >> 1)) / rpm, 1, 0xffe); |
| } |
| |
| static inline unsigned long time_from_reg(u8 reg) |
| { |
| return reg * 100; |
| } |
| |
| static inline u8 time_to_reg(unsigned long val) |
| { |
| return SENSORS_LIMIT((val + 50) / 100, 0, 0xff); |
| } |
| |
| static inline long temp_from_reg(s8 reg) |
| { |
| return reg * 1000; |
| } |
| |
| static inline s8 temp_to_reg(long val, s8 min, s8 max) |
| { |
| return SENSORS_LIMIT((val < 0 ? -val : val) / 1000, min, max); |
| } |
| |
| |
| enum chip_types {w83795g, w83795adg}; |
| |
| struct w83795_data { |
| struct device *hwmon_dev; |
| struct mutex update_lock; |
| unsigned long last_updated; /* In jiffies */ |
| enum chip_types chip_type; |
| |
| u8 bank; |
| |
| u32 has_in; /* Enable monitor VIN or not */ |
| u16 in[21][3]; /* Register value, read/high/low */ |
| u8 in_lsb[10][3]; /* LSB Register value, high/low */ |
| u8 has_gain; /* has gain: in17-20 * 8 */ |
| |
| u16 has_fan; /* Enable fan14-1 or not */ |
| u16 fan[14]; /* Register value combine */ |
| u16 fan_min[14]; /* Register value combine */ |
| |
| u8 has_temp; /* Enable monitor temp6-1 or not */ |
| u8 temp[6][5]; /* current, crit, crit_hyst, warn, warn_hyst */ |
| u8 temp_read_vrlsb[6]; |
| u8 temp_mode; /* bit 0: TR mode, bit 1: TD mode */ |
| u8 temp_src[3]; /* Register value */ |
| |
| u8 enable_dts; /* Enable PECI and SB-TSI, |
| * bit 0: =1 enable, =0 disable, |
| * bit 1: =1 AMD SB-TSI, =0 Intel PECI */ |
| u8 has_dts; /* Enable monitor DTS temp */ |
| u8 dts[8]; /* Register value */ |
| u8 dts_read_vrlsb[8]; /* Register value */ |
| u8 dts_ext[4]; /* Register value */ |
| |
| u8 has_pwm; /* 795g supports 8 pwm, 795adg only supports 2, |
| * no config register, only affected by chip |
| * type */ |
| u8 pwm[8][5]; /* Register value, output, start, non stop, stop |
| * time, div */ |
| u8 pwm_fcms[2]; /* Register value */ |
| u8 pwm_tfmr[6]; /* Register value */ |
| u8 pwm_fomc; /* Register value */ |
| |
| u16 target_speed[8]; /* Register value, target speed for speed |
| * cruise */ |
| u8 tol_speed; /* tolerance of target speed */ |
| u8 pwm_temp[6][4]; /* TTTI, CTFS, HCT, HOT */ |
| u8 sf4_reg[6][2][7]; /* 6 temp, temp/dcpwm, 7 registers */ |
| |
| u8 setup_pwm[3]; /* Register value */ |
| |
| u8 alarms[6]; /* Register value */ |
| u8 beeps[6]; /* Register value */ |
| u8 beep_enable; |
| |
| char valid; |
| }; |
| |
| /* |
| * Hardware access |
| */ |
| |
| /* Ignore the possibility that somebody change bank outside the driver |
| * Must be called with data->update_lock held, except during initialization */ |
| static u8 w83795_read(struct i2c_client *client, u16 reg) |
| { |
| struct w83795_data *data = i2c_get_clientdata(client); |
| u8 res = 0xff; |
| u8 new_bank = reg >> 8; |
| |
| new_bank |= data->bank & 0xfc; |
| if (data->bank != new_bank) { |
| if (i2c_smbus_write_byte_data |
| (client, W83795_REG_BANKSEL, new_bank) >= 0) |
| data->bank = new_bank; |
| else { |
| dev_err(&client->dev, |
| "set bank to %d failed, fall back " |
| "to bank %d, read reg 0x%x error\n", |
| new_bank, data->bank, reg); |
| res = 0x0; /* read 0x0 from the chip */ |
| goto END; |
| } |
| } |
| res = i2c_smbus_read_byte_data(client, reg & 0xff); |
| END: |
| return res; |
| } |
| |
| /* Must be called with data->update_lock held, except during initialization */ |
| static int w83795_write(struct i2c_client *client, u16 reg, u8 value) |
| { |
| struct w83795_data *data = i2c_get_clientdata(client); |
| int res; |
| u8 new_bank = reg >> 8; |
| |
| new_bank |= data->bank & 0xfc; |
| if (data->bank != new_bank) { |
| res = i2c_smbus_write_byte_data(client, W83795_REG_BANKSEL, |
| new_bank); |
| if (res >= 0) |
| data->bank = new_bank; |
| else { |
| dev_err(&client->dev, |
| "set bank to %d failed, fall back " |
| "to bank %d, write reg 0x%x error\n", |
| new_bank, data->bank, reg); |
| goto END; |
| } |
| } |
| |
| res = i2c_smbus_write_byte_data(client, reg & 0xff, value); |
| END: |
| return res; |
| } |
| |
| static struct w83795_data *w83795_update_device(struct device *dev) |
| { |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| u16 tmp; |
| int i; |
| |
| mutex_lock(&data->update_lock); |
| |
| if (!(time_after(jiffies, data->last_updated + HZ * 2) |
| || !data->valid)) |
| goto END; |
| |
| /* Update the voltages value */ |
| for (i = 0; i < ARRAY_SIZE(data->in); i++) { |
| if (!(data->has_in & (1 << i))) |
| continue; |
| tmp = w83795_read(client, W83795_REG_IN[i][IN_READ]) << 2; |
| tmp |= (w83795_read(client, W83795_REG_VRLSB) |
| >> VRLSB_SHIFT) & 0x03; |
| data->in[i][IN_READ] = tmp; |
| } |
| |
| /* Update fan */ |
| for (i = 0; i < ARRAY_SIZE(data->fan); i++) { |
| if (!(data->has_fan & (1 << i))) |
| continue; |
| data->fan[i] = w83795_read(client, W83795_REG_FAN(i)) << 4; |
| data->fan[i] |= |
| (w83795_read(client, W83795_REG_VRLSB >> 4)) & 0x0F; |
| } |
| |
| /* Update temperature */ |
| for (i = 0; i < ARRAY_SIZE(data->temp); i++) { |
| /* even stop monitor, register still keep value, just read out |
| * it */ |
| if (!(data->has_temp & (1 << i))) { |
| data->temp[i][TEMP_READ] = 0; |
| data->temp_read_vrlsb[i] = 0; |
| continue; |
| } |
| data->temp[i][TEMP_READ] = |
| w83795_read(client, W83795_REG_TEMP[i][TEMP_READ]); |
| data->temp_read_vrlsb[i] = |
| w83795_read(client, W83795_REG_VRLSB); |
| } |
| |
| /* Update dts temperature */ |
| if (data->enable_dts != 0) { |
| for (i = 0; i < ARRAY_SIZE(data->dts); i++) { |
| if (!(data->has_dts & (1 << i))) |
| continue; |
| data->dts[i] = |
| w83795_read(client, W83795_REG_DTS(i)); |
| data->dts_read_vrlsb[i] = |
| w83795_read(client, W83795_REG_VRLSB); |
| } |
| } |
| |
| /* Update pwm output */ |
| for (i = 0; i < data->has_pwm; i++) { |
| data->pwm[i][PWM_OUTPUT] = |
| w83795_read(client, W83795_REG_PWM(i, PWM_OUTPUT)); |
| } |
| |
| /* update alarm */ |
| for (i = 0; i < ALARM_BEEP_REG_NUM; i++) |
| data->alarms[i] = w83795_read(client, W83795_REG_ALARM(i)); |
| |
| data->last_updated = jiffies; |
| data->valid = 1; |
| |
| END: |
| mutex_unlock(&data->update_lock); |
| return data; |
| } |
| |
| /* |
| * Sysfs attributes |
| */ |
| |
| #define ALARM_STATUS 0 |
| #define BEEP_ENABLE 1 |
| static ssize_t |
| show_alarm_beep(struct device *dev, struct device_attribute *attr, char *buf) |
| { |
| struct w83795_data *data = w83795_update_device(dev); |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int nr = sensor_attr->nr; |
| int index = sensor_attr->index >> 3; |
| int bit = sensor_attr->index & 0x07; |
| u8 val; |
| |
| if (ALARM_STATUS == nr) { |
| val = (data->alarms[index] >> (bit)) & 1; |
| } else { /* BEEP_ENABLE */ |
| val = (data->beeps[index] >> (bit)) & 1; |
| } |
| |
| return sprintf(buf, "%u\n", val); |
| } |
| |
| static ssize_t |
| store_beep(struct device *dev, struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int index = sensor_attr->index >> 3; |
| int shift = sensor_attr->index & 0x07; |
| u8 beep_bit = 1 << shift; |
| unsigned long val; |
| |
| if (strict_strtoul(buf, 10, &val) < 0) |
| return -EINVAL; |
| if (val != 0 && val != 1) |
| return -EINVAL; |
| |
| mutex_lock(&data->update_lock); |
| data->beeps[index] = w83795_read(client, W83795_REG_BEEP(index)); |
| data->beeps[index] &= ~beep_bit; |
| data->beeps[index] |= val << shift; |
| w83795_write(client, W83795_REG_BEEP(index), data->beeps[index]); |
| mutex_unlock(&data->update_lock); |
| |
| return count; |
| } |
| |
| static ssize_t |
| show_beep_enable(struct device *dev, struct device_attribute *attr, char *buf) |
| { |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| return sprintf(buf, "%u\n", data->beep_enable); |
| } |
| |
| static ssize_t |
| store_beep_enable(struct device *dev, struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| unsigned long val; |
| u8 tmp; |
| |
| if (strict_strtoul(buf, 10, &val) < 0) |
| return -EINVAL; |
| if (val != 0 && val != 1) |
| return -EINVAL; |
| |
| mutex_lock(&data->update_lock); |
| data->beep_enable = val; |
| tmp = w83795_read(client, W83795_REG_BEEP(5)); |
| tmp &= 0x7f; |
| tmp |= val << 7; |
| w83795_write(client, W83795_REG_BEEP(5), tmp); |
| mutex_unlock(&data->update_lock); |
| |
| return count; |
| } |
| |
| /* Write any value to clear chassis alarm */ |
| static ssize_t |
| store_chassis_clear(struct device *dev, |
| struct device_attribute *attr, const char *buf, |
| size_t count) |
| { |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| u8 val; |
| |
| mutex_lock(&data->update_lock); |
| val = w83795_read(client, W83795_REG_CLR_CHASSIS); |
| val |= 0x80; |
| w83795_write(client, W83795_REG_CLR_CHASSIS, val); |
| mutex_unlock(&data->update_lock); |
| return count; |
| } |
| |
| #define FAN_INPUT 0 |
| #define FAN_MIN 1 |
| static ssize_t |
| show_fan(struct device *dev, struct device_attribute *attr, char *buf) |
| { |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int nr = sensor_attr->nr; |
| int index = sensor_attr->index; |
| struct w83795_data *data = w83795_update_device(dev); |
| u16 val; |
| |
| if (FAN_INPUT == nr) |
| val = data->fan[index] & 0x0fff; |
| else |
| val = data->fan_min[index] & 0x0fff; |
| |
| return sprintf(buf, "%lu\n", fan_from_reg(val)); |
| } |
| |
| static ssize_t |
| store_fan_min(struct device *dev, struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int index = sensor_attr->index; |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| unsigned long val; |
| |
| if (strict_strtoul(buf, 10, &val)) |
| return -EINVAL; |
| val = fan_to_reg(val); |
| |
| mutex_lock(&data->update_lock); |
| data->fan_min[index] = val; |
| w83795_write(client, W83795_REG_FAN_MIN_HL(index), (val >> 4) & 0xff); |
| val &= 0x0f; |
| if (index % 1) { |
| val <<= 4; |
| val |= w83795_read(client, W83795_REG_FAN_MIN_LSB(index)) |
| & 0x0f; |
| } else { |
| val |= w83795_read(client, W83795_REG_FAN_MIN_LSB(index)) |
| & 0xf0; |
| } |
| w83795_write(client, W83795_REG_FAN_MIN_LSB(index), val & 0xff); |
| mutex_unlock(&data->update_lock); |
| |
| return count; |
| } |
| |
| static ssize_t |
| show_pwm(struct device *dev, struct device_attribute *attr, char *buf) |
| { |
| struct w83795_data *data = w83795_update_device(dev); |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int nr = sensor_attr->nr; |
| int index = sensor_attr->index; |
| u16 val; |
| |
| switch (nr) { |
| case PWM_STOP_TIME: |
| val = time_from_reg(data->pwm[index][nr]); |
| break; |
| case PWM_DIV: |
| val = W83795_REG_FOPFP_DIV(data->pwm[index][nr] & 0x0f); |
| break; |
| default: |
| val = data->pwm[index][nr]; |
| break; |
| } |
| |
| return sprintf(buf, "%u\n", val); |
| } |
| |
| static ssize_t |
| store_pwm(struct device *dev, struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int nr = sensor_attr->nr; |
| int index = sensor_attr->index; |
| unsigned long val; |
| int i; |
| |
| if (strict_strtoul(buf, 10, &val) < 0) |
| return -EINVAL; |
| |
| mutex_lock(&data->update_lock); |
| switch (nr) { |
| case PWM_STOP_TIME: |
| val = time_to_reg(val); |
| break; |
| case PWM_DIV: |
| for (i = 0; i < 16; i++) { |
| if (W83795_REG_FOPFP_DIV(i) == val) { |
| val = i; |
| break; |
| } |
| } |
| if (i >= 16) |
| goto err_end; |
| val |= w83795_read(client, W83795_REG_PWM(index, nr)) & 0x80; |
| break; |
| default: |
| val = SENSORS_LIMIT(val, 0, 0xff); |
| break; |
| } |
| w83795_write(client, W83795_REG_PWM(index, nr), val); |
| data->pwm[index][nr] = val & 0xff; |
| mutex_unlock(&data->update_lock); |
| return count; |
| err_end: |
| mutex_unlock(&data->update_lock); |
| return -EINVAL; |
| } |
| |
| static ssize_t |
| show_pwm_enable(struct device *dev, struct device_attribute *attr, char *buf) |
| { |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| int index = sensor_attr->index; |
| u8 tmp; |
| |
| if (1 == (data->pwm_fcms[0] & (1 << index))) { |
| tmp = 2; |
| goto out; |
| } |
| for (tmp = 0; tmp < 6; tmp++) { |
| if (data->pwm_tfmr[tmp] & (1 << index)) { |
| tmp = 3; |
| goto out; |
| } |
| } |
| if (data->pwm_fomc & (1 << index)) |
| tmp = 0; |
| else |
| tmp = 1; |
| |
| out: |
| return sprintf(buf, "%u\n", tmp); |
| } |
| |
| static ssize_t |
| store_pwm_enable(struct device *dev, struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int index = sensor_attr->index; |
| unsigned long val; |
| int i; |
| |
| if (strict_strtoul(buf, 10, &val) < 0) |
| return -EINVAL; |
| if (val > 2) |
| return -EINVAL; |
| |
| mutex_lock(&data->update_lock); |
| switch (val) { |
| case 0: |
| case 1: |
| data->pwm_fcms[0] &= ~(1 << index); |
| w83795_write(client, W83795_REG_FCMS1, data->pwm_fcms[0]); |
| for (i = 0; i < 6; i++) { |
| data->pwm_tfmr[i] &= ~(1 << index); |
| w83795_write(client, W83795_REG_TFMR(i), |
| data->pwm_tfmr[i]); |
| } |
| data->pwm_fomc |= 1 << index; |
| data->pwm_fomc ^= val << index; |
| w83795_write(client, W83795_REG_FOMC, data->pwm_fomc); |
| break; |
| case 2: |
| data->pwm_fcms[0] |= (1 << index); |
| w83795_write(client, W83795_REG_FCMS1, data->pwm_fcms[0]); |
| break; |
| } |
| mutex_unlock(&data->update_lock); |
| return count; |
| } |
| |
| static ssize_t |
| show_temp_src(struct device *dev, struct device_attribute *attr, char *buf) |
| { |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| int index = sensor_attr->index; |
| u8 val = index / 2; |
| u8 tmp = data->temp_src[val]; |
| |
| if (index % 1) |
| val = 4; |
| else |
| val = 0; |
| tmp >>= val; |
| tmp &= 0x0f; |
| |
| return sprintf(buf, "%u\n", tmp); |
| } |
| |
| static ssize_t |
| store_temp_src(struct device *dev, struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int index = sensor_attr->index; |
| unsigned long tmp; |
| u8 val = index / 2; |
| |
| if (strict_strtoul(buf, 10, &tmp) < 0) |
| return -EINVAL; |
| tmp = SENSORS_LIMIT(tmp, 0, 15); |
| |
| mutex_lock(&data->update_lock); |
| if (index % 1) { |
| tmp <<= 4; |
| data->temp_src[val] &= 0x0f; |
| } else { |
| data->temp_src[val] &= 0xf0; |
| } |
| data->temp_src[val] |= tmp; |
| w83795_write(client, W83795_REG_TSS(val), data->temp_src[val]); |
| mutex_unlock(&data->update_lock); |
| |
| return count; |
| } |
| |
| #define TEMP_PWM_ENABLE 0 |
| #define TEMP_PWM_FAN_MAP 1 |
| static ssize_t |
| show_temp_pwm_enable(struct device *dev, struct device_attribute *attr, |
| char *buf) |
| { |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int nr = sensor_attr->nr; |
| int index = sensor_attr->index; |
| u8 tmp = 0xff; |
| |
| switch (nr) { |
| case TEMP_PWM_ENABLE: |
| tmp = (data->pwm_fcms[1] >> index) & 1; |
| if (tmp) |
| tmp = 4; |
| else |
| tmp = 3; |
| break; |
| case TEMP_PWM_FAN_MAP: |
| tmp = data->pwm_tfmr[index]; |
| break; |
| } |
| |
| return sprintf(buf, "%u\n", tmp); |
| } |
| |
| static ssize_t |
| store_temp_pwm_enable(struct device *dev, struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int nr = sensor_attr->nr; |
| int index = sensor_attr->index; |
| unsigned long tmp; |
| |
| if (strict_strtoul(buf, 10, &tmp) < 0) |
| return -EINVAL; |
| |
| switch (nr) { |
| case TEMP_PWM_ENABLE: |
| if ((tmp != 3) && (tmp != 4)) |
| return -EINVAL; |
| tmp -= 3; |
| mutex_lock(&data->update_lock); |
| data->pwm_fcms[1] &= ~(1 << index); |
| data->pwm_fcms[1] |= tmp << index; |
| w83795_write(client, W83795_REG_FCMS2, data->pwm_fcms[1]); |
| mutex_unlock(&data->update_lock); |
| break; |
| case TEMP_PWM_FAN_MAP: |
| mutex_lock(&data->update_lock); |
| tmp = SENSORS_LIMIT(tmp, 0, 0xff); |
| w83795_write(client, W83795_REG_TFMR(index), tmp); |
| data->pwm_tfmr[index] = tmp; |
| mutex_unlock(&data->update_lock); |
| break; |
| } |
| return count; |
| } |
| |
| #define FANIN_TARGET 0 |
| #define FANIN_TOL 1 |
| static ssize_t |
| show_fanin(struct device *dev, struct device_attribute *attr, char *buf) |
| { |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int nr = sensor_attr->nr; |
| int index = sensor_attr->index; |
| u16 tmp = 0; |
| |
| switch (nr) { |
| case FANIN_TARGET: |
| tmp = fan_from_reg(data->target_speed[index]); |
| break; |
| case FANIN_TOL: |
| tmp = data->tol_speed; |
| break; |
| } |
| |
| return sprintf(buf, "%u\n", tmp); |
| } |
| |
| static ssize_t |
| store_fanin(struct device *dev, struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int nr = sensor_attr->nr; |
| int index = sensor_attr->index; |
| unsigned long val; |
| |
| if (strict_strtoul(buf, 10, &val) < 0) |
| return -EINVAL; |
| |
| mutex_lock(&data->update_lock); |
| switch (nr) { |
| case FANIN_TARGET: |
| val = fan_to_reg(SENSORS_LIMIT(val, 0, 0xfff)); |
| w83795_write(client, W83795_REG_FTSH(index), (val >> 4) & 0xff); |
| w83795_write(client, W83795_REG_FTSL(index), (val << 4) & 0xf0); |
| data->target_speed[index] = val; |
| break; |
| case FANIN_TOL: |
| val = SENSORS_LIMIT(val, 0, 0x3f); |
| w83795_write(client, W83795_REG_TFTS, val); |
| data->tol_speed = val; |
| break; |
| } |
| mutex_unlock(&data->update_lock); |
| |
| return count; |
| } |
| |
| |
| static ssize_t |
| show_temp_pwm(struct device *dev, struct device_attribute *attr, char *buf) |
| { |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int nr = sensor_attr->nr; |
| int index = sensor_attr->index; |
| long tmp = temp_from_reg(data->pwm_temp[index][nr]); |
| |
| return sprintf(buf, "%ld\n", tmp); |
| } |
| |
| static ssize_t |
| store_temp_pwm(struct device *dev, struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int nr = sensor_attr->nr; |
| int index = sensor_attr->index; |
| unsigned long val; |
| u8 tmp; |
| |
| if (strict_strtoul(buf, 10, &val) < 0) |
| return -EINVAL; |
| val /= 1000; |
| |
| mutex_lock(&data->update_lock); |
| switch (nr) { |
| case TEMP_PWM_TTTI: |
| val = SENSORS_LIMIT(val, 0, 0x7f); |
| w83795_write(client, W83795_REG_TTTI(index), val); |
| break; |
| case TEMP_PWM_CTFS: |
| val = SENSORS_LIMIT(val, 0, 0x7f); |
| w83795_write(client, W83795_REG_CTFS(index), val); |
| break; |
| case TEMP_PWM_HCT: |
| val = SENSORS_LIMIT(val, 0, 0x0f); |
| tmp = w83795_read(client, W83795_REG_HT(index)); |
| tmp &= 0x0f; |
| tmp |= (val << 4) & 0xf0; |
| w83795_write(client, W83795_REG_HT(index), tmp); |
| break; |
| case TEMP_PWM_HOT: |
| val = SENSORS_LIMIT(val, 0, 0x0f); |
| tmp = w83795_read(client, W83795_REG_HT(index)); |
| tmp &= 0xf0; |
| tmp |= val & 0x0f; |
| w83795_write(client, W83795_REG_HT(index), tmp); |
| break; |
| } |
| data->pwm_temp[index][nr] = val; |
| mutex_unlock(&data->update_lock); |
| |
| return count; |
| } |
| |
| static ssize_t |
| show_sf4_pwm(struct device *dev, struct device_attribute *attr, char *buf) |
| { |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int nr = sensor_attr->nr; |
| int index = sensor_attr->index; |
| |
| return sprintf(buf, "%u\n", data->sf4_reg[index][SF4_PWM][nr]); |
| } |
| |
| static ssize_t |
| store_sf4_pwm(struct device *dev, struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int nr = sensor_attr->nr; |
| int index = sensor_attr->index; |
| unsigned long val; |
| |
| if (strict_strtoul(buf, 10, &val) < 0) |
| return -EINVAL; |
| |
| mutex_lock(&data->update_lock); |
| w83795_write(client, W83795_REG_SF4_PWM(index, nr), val); |
| data->sf4_reg[index][SF4_PWM][nr] = val; |
| mutex_unlock(&data->update_lock); |
| |
| return count; |
| } |
| |
| static ssize_t |
| show_sf4_temp(struct device *dev, struct device_attribute *attr, char *buf) |
| { |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int nr = sensor_attr->nr; |
| int index = sensor_attr->index; |
| |
| return sprintf(buf, "%u\n", |
| (data->sf4_reg[index][SF4_TEMP][nr]) * 1000); |
| } |
| |
| static ssize_t |
| store_sf4_temp(struct device *dev, struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int nr = sensor_attr->nr; |
| int index = sensor_attr->index; |
| unsigned long val; |
| |
| if (strict_strtoul(buf, 10, &val) < 0) |
| return -EINVAL; |
| val /= 1000; |
| |
| mutex_lock(&data->update_lock); |
| w83795_write(client, W83795_REG_SF4_TEMP(index, nr), val); |
| data->sf4_reg[index][SF4_TEMP][nr] = val; |
| mutex_unlock(&data->update_lock); |
| |
| return count; |
| } |
| |
| |
| static ssize_t |
| show_temp(struct device *dev, struct device_attribute *attr, char *buf) |
| { |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int nr = sensor_attr->nr; |
| int index = sensor_attr->index; |
| struct w83795_data *data = w83795_update_device(dev); |
| long temp = temp_from_reg(data->temp[index][nr] & 0x7f); |
| |
| if (TEMP_READ == nr) |
| temp += ((data->temp_read_vrlsb[index] >> VRLSB_SHIFT) & 0x03) |
| * 250; |
| if (data->temp[index][nr] & 0x80) |
| temp = -temp; |
| return sprintf(buf, "%ld\n", temp); |
| } |
| |
| static ssize_t |
| store_temp(struct device *dev, struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int nr = sensor_attr->nr; |
| int index = sensor_attr->index; |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| long tmp; |
| |
| if (strict_strtol(buf, 10, &tmp) < 0) |
| return -EINVAL; |
| |
| mutex_lock(&data->update_lock); |
| data->temp[index][nr] = temp_to_reg(tmp, -128, 127); |
| w83795_write(client, W83795_REG_TEMP[index][nr], data->temp[index][nr]); |
| mutex_unlock(&data->update_lock); |
| return count; |
| } |
| |
| |
| static ssize_t |
| show_dts_mode(struct device *dev, struct device_attribute *attr, char *buf) |
| { |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int index = sensor_attr->index; |
| u8 tmp; |
| |
| if (data->enable_dts == 0) |
| return sprintf(buf, "%d\n", 0); |
| |
| if ((data->has_dts >> index) & 0x01) { |
| if (data->enable_dts & 2) |
| tmp = 5; |
| else |
| tmp = 6; |
| } else { |
| tmp = 0; |
| } |
| |
| return sprintf(buf, "%d\n", tmp); |
| } |
| |
| static ssize_t |
| show_dts(struct device *dev, struct device_attribute *attr, char *buf) |
| { |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int index = sensor_attr->index; |
| struct w83795_data *data = w83795_update_device(dev); |
| long temp = temp_from_reg(data->dts[index] & 0x7f); |
| |
| temp += ((data->dts_read_vrlsb[index] >> VRLSB_SHIFT) & 0x03) * 250; |
| if (data->dts[index] & 0x80) |
| temp = -temp; |
| return sprintf(buf, "%ld\n", temp); |
| } |
| |
| static ssize_t |
| show_dts_ext(struct device *dev, struct device_attribute *attr, char *buf) |
| { |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int nr = sensor_attr->nr; |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| long temp = temp_from_reg(data->dts_ext[nr] & 0x7f); |
| |
| if (data->dts_ext[nr] & 0x80) |
| temp = -temp; |
| return sprintf(buf, "%ld\n", temp); |
| } |
| |
| static ssize_t |
| store_dts_ext(struct device *dev, struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int nr = sensor_attr->nr; |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| long tmp; |
| |
| if (strict_strtol(buf, 10, &tmp) < 0) |
| return -EINVAL; |
| |
| mutex_lock(&data->update_lock); |
| data->dts_ext[nr] = temp_to_reg(tmp, -128, 127); |
| w83795_write(client, W83795_REG_DTS_EXT(nr), data->dts_ext[nr]); |
| mutex_unlock(&data->update_lock); |
| return count; |
| } |
| |
| |
| /* |
| Type 3: Thermal diode |
| Type 4: Thermistor |
| |
| Temp5-6, default TR |
| Temp1-4, default TD |
| */ |
| |
| static ssize_t |
| show_temp_mode(struct device *dev, struct device_attribute *attr, char *buf) |
| { |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int index = sensor_attr->index; |
| u8 tmp; |
| |
| if (data->has_temp >> index & 0x01) { |
| if (data->temp_mode >> index & 0x01) |
| tmp = 3; |
| else |
| tmp = 4; |
| } else { |
| tmp = 0; |
| } |
| |
| return sprintf(buf, "%d\n", tmp); |
| } |
| |
| static ssize_t |
| store_temp_mode(struct device *dev, struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int index = sensor_attr->index; |
| unsigned long val; |
| u8 tmp; |
| u32 mask; |
| |
| if (strict_strtoul(buf, 10, &val) < 0) |
| return -EINVAL; |
| if ((val != 4) && (val != 3)) |
| return -EINVAL; |
| if ((index > 3) && (val == 3)) |
| return -EINVAL; |
| |
| mutex_lock(&data->update_lock); |
| if (val == 3) { |
| val = TEMP_CTRL_TD; |
| data->has_temp |= 1 << index; |
| data->temp_mode |= 1 << index; |
| } else if (val == 4) { |
| val = TEMP_CTRL_TR; |
| data->has_temp |= 1 << index; |
| tmp = 1 << index; |
| data->temp_mode &= ~tmp; |
| } |
| |
| if (index > 3) |
| tmp = w83795_read(client, W83795_REG_TEMP_CTRL1); |
| else |
| tmp = w83795_read(client, W83795_REG_TEMP_CTRL2); |
| |
| mask = 0x03 << W83795_REG_TEMP_CTRL[index][TEMP_CTRL_SHIFT]; |
| tmp &= ~mask; |
| tmp |= W83795_REG_TEMP_CTRL[index][val]; |
| |
| mask = 1 << W83795_REG_TEMP_CTRL[index][TEMP_CTRL_HASIN_SHIFT]; |
| data->has_in &= ~mask; |
| |
| if (index > 3) |
| w83795_write(client, W83795_REG_TEMP_CTRL1, tmp); |
| else |
| w83795_write(client, W83795_REG_TEMP_CTRL2, tmp); |
| |
| mutex_unlock(&data->update_lock); |
| return count; |
| } |
| |
| |
| /* show/store VIN */ |
| static ssize_t |
| show_in(struct device *dev, struct device_attribute *attr, char *buf) |
| { |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int nr = sensor_attr->nr; |
| int index = sensor_attr->index; |
| struct w83795_data *data = w83795_update_device(dev); |
| u16 val = data->in[index][nr]; |
| u8 lsb_idx; |
| |
| switch (nr) { |
| case IN_READ: |
| /* calculate this value again by sensors as sensors3.conf */ |
| if ((index >= 17) && |
| ((data->has_gain >> (index - 17)) & 1)) |
| val *= 8; |
| break; |
| case IN_MAX: |
| case IN_LOW: |
| lsb_idx = IN_LSB_SHIFT_IDX[index][IN_LSB_IDX]; |
| val <<= 2; |
| val |= (data->in_lsb[lsb_idx][nr] >> |
| IN_LSB_SHIFT_IDX[lsb_idx][IN_LSB_SHIFT]) & 0x03; |
| if ((index >= 17) && |
| ((data->has_gain >> (index - 17)) & 1)) |
| val *= 8; |
| break; |
| } |
| val = in_from_reg(index, val); |
| |
| return sprintf(buf, "%d\n", val); |
| } |
| |
| static ssize_t |
| store_in(struct device *dev, struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int nr = sensor_attr->nr; |
| int index = sensor_attr->index; |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| unsigned long val; |
| u8 tmp; |
| u8 lsb_idx; |
| |
| if (strict_strtoul(buf, 10, &val) < 0) |
| return -EINVAL; |
| val = in_to_reg(index, val); |
| |
| if ((index >= 17) && |
| ((data->has_gain >> (index - 17)) & 1)) |
| val /= 8; |
| val = SENSORS_LIMIT(val, 0, 0x3FF); |
| mutex_lock(&data->update_lock); |
| |
| lsb_idx = IN_LSB_SHIFT_IDX[index][IN_LSB_IDX]; |
| tmp = w83795_read(client, IN_LSB_REG(lsb_idx, nr)); |
| tmp &= ~(0x03 << IN_LSB_SHIFT_IDX[index][IN_LSB_SHIFT]); |
| tmp |= (val & 0x03) << IN_LSB_SHIFT_IDX[index][IN_LSB_SHIFT]; |
| w83795_write(client, IN_LSB_REG(lsb_idx, nr), tmp); |
| data->in_lsb[lsb_idx][nr] = tmp; |
| |
| tmp = (val >> 2) & 0xff; |
| w83795_write(client, W83795_REG_IN[index][nr], tmp); |
| data->in[index][nr] = tmp; |
| |
| mutex_unlock(&data->update_lock); |
| return count; |
| } |
| |
| |
| static ssize_t |
| show_sf_setup(struct device *dev, struct device_attribute *attr, char *buf) |
| { |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int nr = sensor_attr->nr; |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| u16 val = data->setup_pwm[nr]; |
| |
| switch (nr) { |
| case SETUP_PWM_UPTIME: |
| case SETUP_PWM_DOWNTIME: |
| val = time_from_reg(val); |
| break; |
| } |
| |
| return sprintf(buf, "%d\n", val); |
| } |
| |
| static ssize_t |
| store_sf_setup(struct device *dev, struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct sensor_device_attribute_2 *sensor_attr = |
| to_sensor_dev_attr_2(attr); |
| int nr = sensor_attr->nr; |
| struct i2c_client *client = to_i2c_client(dev); |
| struct w83795_data *data = i2c_get_clientdata(client); |
| unsigned long val; |
| |
| if (strict_strtoul(buf, 10, &val) < 0) |
| return -EINVAL; |
| |
| switch (nr) { |
| case SETUP_PWM_DEFAULT: |
| val = SENSORS_LIMIT(val, 0, 0xff); |
| break; |
| case SETUP_PWM_UPTIME: |
| case SETUP_PWM_DOWNTIME: |
| val = time_to_reg(val); |
| if (val == 0) |
| return -EINVAL; |
| break; |
| } |
| |
| mutex_lock(&data->update_lock); |
| data->setup_pwm[nr] = val; |
| w83795_write(client, W83795_REG_SETUP_PWM(nr), val); |
| mutex_unlock(&data->update_lock); |
| return count; |
| } |
| |
| |
| #define NOT_USED -1 |
| |
| #define SENSOR_ATTR_IN(index) \ |
| SENSOR_ATTR_2(in##index##_input, S_IRUGO, show_in, NULL, \ |
| IN_READ, index), \ |
| SENSOR_ATTR_2(in##index##_max, S_IRUGO | S_IWUSR, show_in, \ |
| store_in, IN_MAX, index), \ |
| SENSOR_ATTR_2(in##index##_min, S_IRUGO | S_IWUSR, show_in, \ |
| store_in, IN_LOW, index), \ |
| SENSOR_ATTR_2(in##index##_alarm, S_IRUGO, show_alarm_beep, \ |
| NULL, ALARM_STATUS, index + ((index > 14) ? 1 : 0)), \ |
| SENSOR_ATTR_2(in##index##_beep, S_IWUSR | S_IRUGO, \ |
| show_alarm_beep, store_beep, BEEP_ENABLE, \ |
| index + ((index > 14) ? 1 : 0)) |
| |
| #define SENSOR_ATTR_FAN(index) \ |
| SENSOR_ATTR_2(fan##index##_input, S_IRUGO, show_fan, \ |
| NULL, FAN_INPUT, index - 1), \ |
| SENSOR_ATTR_2(fan##index##_min, S_IWUSR | S_IRUGO, \ |
| show_fan, store_fan_min, FAN_MIN, index - 1), \ |
| SENSOR_ATTR_2(fan##index##_alarm, S_IRUGO, show_alarm_beep, \ |
| NULL, ALARM_STATUS, index + 31), \ |
| SENSOR_ATTR_2(fan##index##_beep, S_IWUSR | S_IRUGO, \ |
| show_alarm_beep, store_beep, BEEP_ENABLE, index + 31) |
| |
| #define SENSOR_ATTR_PWM(index) \ |
| SENSOR_ATTR_2(pwm##index, S_IWUSR | S_IRUGO, show_pwm, \ |
| store_pwm, PWM_OUTPUT, index - 1), \ |
| SENSOR_ATTR_2(pwm##index##_nonstop, S_IWUSR | S_IRUGO, \ |
| show_pwm, store_pwm, PWM_NONSTOP, index - 1), \ |
| SENSOR_ATTR_2(pwm##index##_start, S_IWUSR | S_IRUGO, \ |
| show_pwm, store_pwm, PWM_START, index - 1), \ |
| SENSOR_ATTR_2(pwm##index##_stop_time, S_IWUSR | S_IRUGO, \ |
| show_pwm, store_pwm, PWM_STOP_TIME, index - 1), \ |
| SENSOR_ATTR_2(fan##index##_div, S_IWUSR | S_IRUGO, \ |
| show_pwm, store_pwm, PWM_DIV, index - 1), \ |
| SENSOR_ATTR_2(pwm##index##_enable, S_IWUSR | S_IRUGO, \ |
| show_pwm_enable, store_pwm_enable, NOT_USED, index - 1) |
| |
| #define SENSOR_ATTR_FANIN_TARGET(index) \ |
| SENSOR_ATTR_2(speed_cruise##index##_target, S_IWUSR | S_IRUGO, \ |
| show_fanin, store_fanin, FANIN_TARGET, index - 1) |
| |
| #define SENSOR_ATTR_DTS(index) \ |
| SENSOR_ATTR_2(temp##index##_type, S_IRUGO , \ |
| show_dts_mode, NULL, NOT_USED, index - 7), \ |
| SENSOR_ATTR_2(temp##index##_input, S_IRUGO, show_dts, \ |
| NULL, NOT_USED, index - 7), \ |
| SENSOR_ATTR_2(temp##index##_max, S_IRUGO | S_IWUSR, show_dts_ext, \ |
| store_dts_ext, DTS_CRIT, NOT_USED), \ |
| SENSOR_ATTR_2(temp##index##_max_hyst, S_IRUGO | S_IWUSR, \ |
| show_dts_ext, store_dts_ext, DTS_CRIT_HYST, NOT_USED), \ |
| SENSOR_ATTR_2(temp##index##_warn, S_IRUGO | S_IWUSR, show_dts_ext, \ |
| store_dts_ext, DTS_WARN, NOT_USED), \ |
| SENSOR_ATTR_2(temp##index##_warn_hyst, S_IRUGO | S_IWUSR, \ |
| show_dts_ext, store_dts_ext, DTS_WARN_HYST, NOT_USED), \ |
| SENSOR_ATTR_2(temp##index##_alarm, S_IRUGO, \ |
| show_alarm_beep, NULL, ALARM_STATUS, index + 17), \ |
| SENSOR_ATTR_2(temp##index##_beep, S_IWUSR | S_IRUGO, \ |
| show_alarm_beep, store_beep, BEEP_ENABLE, index + 17) |
| |
| #define SENSOR_ATTR_TEMP(index) \ |
| SENSOR_ATTR_2(temp##index##_type, S_IRUGO | S_IWUSR, \ |
| show_temp_mode, store_temp_mode, NOT_USED, index - 1), \ |
| SENSOR_ATTR_2(temp##index##_input, S_IRUGO, show_temp, \ |
| NULL, TEMP_READ, index - 1), \ |
| SENSOR_ATTR_2(temp##index##_max, S_IRUGO | S_IWUSR, show_temp, \ |
| store_temp, TEMP_CRIT, index - 1), \ |
| SENSOR_ATTR_2(temp##index##_max_hyst, S_IRUGO | S_IWUSR, \ |
| show_temp, store_temp, TEMP_CRIT_HYST, index - 1), \ |
| SENSOR_ATTR_2(temp##index##_warn, S_IRUGO | S_IWUSR, show_temp, \ |
| store_temp, TEMP_WARN, index - 1), \ |
| SENSOR_ATTR_2(temp##index##_warn_hyst, S_IRUGO | S_IWUSR, \ |
| show_temp, store_temp, TEMP_WARN_HYST, index - 1), \ |
| SENSOR_ATTR_2(temp##index##_alarm, S_IRUGO, \ |
| show_alarm_beep, NULL, ALARM_STATUS, \ |
| index + (index > 4 ? 11 : 17)), \ |
| SENSOR_ATTR_2(temp##index##_beep, S_IWUSR | S_IRUGO, \ |
| show_alarm_beep, store_beep, BEEP_ENABLE, \ |
| index + (index > 4 ? 11 : 17)), \ |
| SENSOR_ATTR_2(temp##index##_source_sel, S_IWUSR | S_IRUGO, \ |
| show_temp_src, store_temp_src, NOT_USED, index - 1), \ |
| SENSOR_ATTR_2(temp##index##_pwm_enable, S_IWUSR | S_IRUGO, \ |
| show_temp_pwm_enable, store_temp_pwm_enable, \ |
| TEMP_PWM_ENABLE, index - 1), \ |
| SENSOR_ATTR_2(temp##index##_auto_channels_pwm, S_IWUSR | S_IRUGO, \ |
| show_temp_pwm_enable, store_temp_pwm_enable, \ |
| TEMP_PWM_FAN_MAP, index - 1), \ |
| SENSOR_ATTR_2(thermal_cruise##index, S_IWUSR | S_IRUGO, \ |
| show_temp_pwm, store_temp_pwm, TEMP_PWM_TTTI, index - 1), \ |
| SENSOR_ATTR_2(temp##index##_crit, S_IWUSR | S_IRUGO, \ |
| show_temp_pwm, store_temp_pwm, TEMP_PWM_CTFS, index - 1), \ |
| SENSOR_ATTR_2(temp##index##_crit_hyst, S_IWUSR | S_IRUGO, \ |
| show_temp_pwm, store_temp_pwm, TEMP_PWM_HCT, index - 1), \ |
| SENSOR_ATTR_2(temp##index##_operation_hyst, S_IWUSR | S_IRUGO, \ |
| show_temp_pwm, store_temp_pwm, TEMP_PWM_HOT, index - 1), \ |
| SENSOR_ATTR_2(temp##index##_auto_point1_pwm, S_IRUGO | S_IWUSR, \ |
| show_sf4_pwm, store_sf4_pwm, 0, index - 1), \ |
| SENSOR_ATTR_2(temp##index##_auto_point2_pwm, S_IRUGO | S_IWUSR, \ |
| show_sf4_pwm, store_sf4_pwm, 1, index - 1), \ |
| SENSOR_ATTR_2(temp##index##_auto_point3_pwm, S_IRUGO | S_IWUSR, \ |
| show_sf4_pwm, store_sf4_pwm, 2, index - 1), \ |
| SENSOR_ATTR_2(temp##index##_auto_point4_pwm, S_IRUGO | S_IWUSR, \ |
| show_sf4_pwm, store_sf4_pwm, 3, index - 1), \ |
| SENSOR_ATTR_2(temp##index##_auto_point5_pwm, S_IRUGO | S_IWUSR, \ |
| show_sf4_pwm, store_sf4_pwm, 4, index - 1), \ |
| SENSOR_ATTR_2(temp##index##_auto_point6_pwm, S_IRUGO | S_IWUSR, \ |
| show_sf4_pwm, store_sf4_pwm, 5, index - 1), \ |
| SENSOR_ATTR_2(temp##index##_auto_point7_pwm, S_IRUGO | S_IWUSR, \ |
| show_sf4_pwm, store_sf4_pwm, 6, index - 1), \ |
| SENSOR_ATTR_2(temp##index##_auto_point1_temp, S_IRUGO | S_IWUSR,\ |
| show_sf4_temp, store_sf4_temp, 0, index - 1), \ |
| SENSOR_ATTR_2(temp##index##_auto_point2_temp, S_IRUGO | S_IWUSR,\ |
| show_sf4_temp, store_sf4_temp, 1, index - 1), \ |
| SENSOR_ATTR_2(temp##index##_auto_point3_temp, S_IRUGO | S_IWUSR,\ |
| show_sf4_temp, store_sf4_temp, 2, index - 1), \ |
| SENSOR_ATTR_2(temp##index##_auto_point4_temp, S_IRUGO | S_IWUSR,\ |
| show_sf4_temp, store_sf4_temp, 3, index - 1), \ |
| SENSOR_ATTR_2(temp##index##_auto_point5_temp, S_IRUGO | S_IWUSR,\ |
| show_sf4_temp, store_sf4_temp, 4, index - 1), \ |
| SENSOR_ATTR_2(temp##index##_auto_point6_temp, S_IRUGO | S_IWUSR,\ |
| show_sf4_temp, store_sf4_temp, 5, index - 1), \ |
| SENSOR_ATTR_2(temp##index##_auto_point7_temp, S_IRUGO | S_IWUSR,\ |
| show_sf4_temp, store_sf4_temp, 6, index - 1) |
| |
| |
| static struct sensor_device_attribute_2 w83795_in[] = { |
| SENSOR_ATTR_IN(0), |
| SENSOR_ATTR_IN(1), |
| SENSOR_ATTR_IN(2), |
| SENSOR_ATTR_IN(3), |
| SENSOR_ATTR_IN(4), |
| SENSOR_ATTR_IN(5), |
| SENSOR_ATTR_IN(6), |
| SENSOR_ATTR_IN(7), |
| SENSOR_ATTR_IN(8), |
| SENSOR_ATTR_IN(9), |
| SENSOR_ATTR_IN(10), |
| SENSOR_ATTR_IN(11), |
| SENSOR_ATTR_IN(12), |
| SENSOR_ATTR_IN(13), |
| SENSOR_ATTR_IN(14), |
| SENSOR_ATTR_IN(15), |
| SENSOR_ATTR_IN(16), |
| SENSOR_ATTR_IN(17), |
| SENSOR_ATTR_IN(18), |
| SENSOR_ATTR_IN(19), |
| SENSOR_ATTR_IN(20), |
| }; |
| |
| static struct sensor_device_attribute_2 w83795_fan[] = { |
| SENSOR_ATTR_FAN(1), |
| SENSOR_ATTR_FAN(2), |
| SENSOR_ATTR_FAN(3), |
| SENSOR_ATTR_FAN(4), |
| SENSOR_ATTR_FAN(5), |
| SENSOR_ATTR_FAN(6), |
| SENSOR_ATTR_FAN(7), |
| SENSOR_ATTR_FAN(8), |
| SENSOR_ATTR_FAN(9), |
| SENSOR_ATTR_FAN(10), |
| SENSOR_ATTR_FAN(11), |
| SENSOR_ATTR_FAN(12), |
| SENSOR_ATTR_FAN(13), |
| SENSOR_ATTR_FAN(14), |
| }; |
| |
| static struct sensor_device_attribute_2 w83795_temp[] = { |
| SENSOR_ATTR_TEMP(1), |
| SENSOR_ATTR_TEMP(2), |
| SENSOR_ATTR_TEMP(3), |
| SENSOR_ATTR_TEMP(4), |
| SENSOR_ATTR_TEMP(5), |
| SENSOR_ATTR_TEMP(6), |
| }; |
| |
| static struct sensor_device_attribute_2 w83795_dts[] = { |
| SENSOR_ATTR_DTS(7), |
| SENSOR_ATTR_DTS(8), |
| SENSOR_ATTR_DTS(9), |
| SENSOR_ATTR_DTS(10), |
| SENSOR_ATTR_DTS(11), |
| SENSOR_ATTR_DTS(12), |
| SENSOR_ATTR_DTS(13), |
| SENSOR_ATTR_DTS(14), |
| }; |
| |
| static struct sensor_device_attribute_2 w83795_static[] = { |
| SENSOR_ATTR_FANIN_TARGET(1), |
| SENSOR_ATTR_FANIN_TARGET(2), |
| SENSOR_ATTR_FANIN_TARGET(3), |
| SENSOR_ATTR_FANIN_TARGET(4), |
| SENSOR_ATTR_FANIN_TARGET(5), |
| SENSOR_ATTR_FANIN_TARGET(6), |
| SENSOR_ATTR_FANIN_TARGET(7), |
| SENSOR_ATTR_FANIN_TARGET(8), |
| SENSOR_ATTR_PWM(1), |
| SENSOR_ATTR_PWM(2), |
| }; |
| |
| /* all registers existed in 795g than 795adg, |
| * like PWM3 - PWM8 */ |
| static struct sensor_device_attribute_2 w83795_left_reg[] = { |
| SENSOR_ATTR_PWM(3), |
| SENSOR_ATTR_PWM(4), |
| SENSOR_ATTR_PWM(5), |
| SENSOR_ATTR_PWM(6), |
| SENSOR_ATTR_PWM(7), |
| SENSOR_ATTR_PWM(8), |
| }; |
| |
| static struct sensor_device_attribute_2 sda_single_files[] = { |
| SENSOR_ATTR_2(chassis, S_IWUSR | S_IRUGO, show_alarm_beep, |
| store_chassis_clear, ALARM_STATUS, 46), |
| SENSOR_ATTR_2(beep_enable, S_IWUSR | S_IRUGO, show_beep_enable, |
| store_beep_enable, NOT_USED, NOT_USED), |
| SENSOR_ATTR_2(speed_cruise_tolerance, S_IWUSR | S_IRUGO, show_fanin, |
| store_fanin, FANIN_TOL, NOT_USED), |
| SENSOR_ATTR_2(pwm_default, S_IWUSR | S_IRUGO, show_sf_setup, |
| store_sf_setup, SETUP_PWM_DEFAULT, NOT_USED), |
| SENSOR_ATTR_2(pwm_uptime, S_IWUSR | S_IRUGO, show_sf_setup, |
| store_sf_setup, SETUP_PWM_UPTIME, NOT_USED), |
| SENSOR_ATTR_2(pwm_downtime, S_IWUSR | S_IRUGO, show_sf_setup, |
| store_sf_setup, SETUP_PWM_DOWNTIME, NOT_USED), |
| }; |
| |
| /* |
| * Driver interface |
| */ |
| |
| static void w83795_init_client(struct i2c_client *client) |
| { |
| if (reset) |
| w83795_write(client, W83795_REG_CONFIG, 0x80); |
| |
| /* Start monitoring */ |
| w83795_write(client, W83795_REG_CONFIG, |
| w83795_read(client, W83795_REG_CONFIG) | 0x01); |
| } |
| |
| /* Return 0 if detection is successful, -ENODEV otherwise */ |
| static int w83795_detect(struct i2c_client *client, |
| struct i2c_board_info *info) |
| { |
| u8 tmp, bank; |
| struct i2c_adapter *adapter = client->adapter; |
| unsigned short address = client->addr; |
| |
| if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) |
| return -ENODEV; |
| bank = i2c_smbus_read_byte_data(client, W83795_REG_BANKSEL); |
| |
| tmp = bank & 0x80 ? 0x5c : 0xa3; |
| /* Check Nuvoton vendor ID */ |
| if (tmp != i2c_smbus_read_byte_data(client, |
| W83795_REG_VENDORID)) { |
| pr_debug("w83795: Detection failed at check " |
| "vendor id\n"); |
| return -ENODEV; |
| } |
| |
| /* If Nuvoton chip, address of chip and W83795_REG_I2C_ADDR |
| should match */ |
| if ((bank & 0x07) == 0 |
| && (i2c_smbus_read_byte_data(client, W83795_REG_I2C_ADDR) & 0x7f) != |
| address) { |
| pr_debug("w83795: Detection failed at check " |
| "i2c addr\n"); |
| return -ENODEV; |
| } |
| |
| /* Determine the chip type now */ |
| if (0x79 != i2c_smbus_read_byte_data(client, |
| W83795_REG_CHIPID)) { |
| pr_debug("w83795: Detection failed at check " |
| "chip id\n"); |
| return -ENODEV; |
| } |
| |
| #if 0 |
| /* Check 795 chip type: 795G or 795ADG */ |
| if (W83795_REG_CONFIG_CONFIG48 & |
| w83795_read(client, W83795_REG_CONFIG)) { |
| data->chip_type = w83795adg; |
| } else { |
| data->chip_type = w83795g; |
| } |
| #endif |
| |
| /* Fill in the remaining client fields and put into the global list */ |
| strlcpy(info->type, "w83795", I2C_NAME_SIZE); |
| |
| return 0; |
| } |
| |
| static int w83795_probe(struct i2c_client *client, |
| const struct i2c_device_id *id) |
| { |
| int i; |
| u8 tmp; |
| struct device *dev = &client->dev; |
| struct w83795_data *data; |
| int err = 0; |
| |
| data = kzalloc(sizeof(struct w83795_data), GFP_KERNEL); |
| if (!data) { |
| err = -ENOMEM; |
| goto exit; |
| } |
| |
| i2c_set_clientdata(client, data); |
| data->bank = i2c_smbus_read_byte_data(client, W83795_REG_BANKSEL); |
| mutex_init(&data->update_lock); |
| |
| /* Initialize the chip */ |
| w83795_init_client(client); |
| |
| /* Check 795 chip type: 795G or 795ADG */ |
| if (W83795_REG_CONFIG_CONFIG48 & |
| w83795_read(client, W83795_REG_CONFIG)) { |
| data->chip_type = w83795adg; |
| } else { |
| data->chip_type = w83795g; |
| } |
| |
| data->has_in = w83795_read(client, W83795_REG_VOLT_CTRL1); |
| data->has_in |= w83795_read(client, W83795_REG_VOLT_CTRL2) << 8; |
| /* VSEN11-9 not for 795adg */ |
| if (data->chip_type == w83795adg) |
| data->has_in &= 0xf8ff; |
| data->has_fan = w83795_read(client, W83795_REG_FANIN_CTRL1); |
| data->has_fan |= w83795_read(client, W83795_REG_FANIN_CTRL2) << 8; |
| |
| /* VDSEN12-17 and TR1-6, TD1-4 use same register */ |
| tmp = w83795_read(client, W83795_REG_TEMP_CTRL1); |
| if (tmp & 0x20) |
| data->enable_dts = 1; |
| else |
| data->enable_dts = 0; |
| data->has_temp = 0; |
| data->temp_mode = 0; |
| if (tmp & 0x08) { |
| if (tmp & 0x04) |
| data->has_temp |= 0x20; |
| else |
| data->has_in |= 0x10000; |
| } |
| if (tmp & 0x02) { |
| if (tmp & 0x01) |
| data->has_temp |= 0x10; |
| else |
| data->has_in |= 0x8000; |
| } |
| tmp = w83795_read(client, W83795_REG_TEMP_CTRL2); |
| if (tmp & 0x40) { |
| data->has_temp |= 0x08; |
| if (!(tmp & 0x80)) |
| data->temp_mode |= 0x08; |
| } else if (tmp & 0x80) { |
| data->has_in |= 0x100000; |
| } |
| if (tmp & 0x10) { |
| data->has_temp |= 0x04; |
| if (!(tmp & 0x20)) |
| data->temp_mode |= 0x04; |
| } else if (tmp & 0x20) { |
| data->has_in |= 0x80000; |
| } |
| if (tmp & 0x04) { |
| data->has_temp |= 0x02; |
| if (!(tmp & 0x08)) |
| data->temp_mode |= 0x02; |
| } else if (tmp & 0x08) { |
| data->has_in |= 0x40000; |
| } |
| if (tmp & 0x01) { |
| data->has_temp |= 0x01; |
| if (!(tmp & 0x02)) |
| data->temp_mode |= 0x01; |
| } else if (tmp & 0x02) { |
| data->has_in |= 0x20000; |
| } |
| |
| /* Check DTS enable status */ |
| if (data->enable_dts == 0) { |
| data->has_dts = 0; |
| } else { |
| if (1 & w83795_read(client, W83795_REG_DTSC)) |
| data->enable_dts |= 2; |
| data->has_dts = w83795_read(client, W83795_REG_DTSE); |
| } |
| |
| /* First update the voltages measured value and limits */ |
| for (i = 0; i < ARRAY_SIZE(data->in); i++) { |
| if (!(data->has_in & (1 << i))) |
| continue; |
| data->in[i][IN_MAX] = |
| w83795_read(client, W83795_REG_IN[i][IN_MAX]); |
| data->in[i][IN_LOW] = |
| w83795_read(client, W83795_REG_IN[i][IN_LOW]); |
| tmp = w83795_read(client, W83795_REG_IN[i][IN_READ]) << 2; |
| tmp |= (w83795_read(client, W83795_REG_VRLSB) |
| >> VRLSB_SHIFT) & 0x03; |
| data->in[i][IN_READ] = tmp; |
| } |
| for (i = 0; i < IN_LSB_REG_NUM; i++) { |
| data->in_lsb[i][IN_MAX] = |
| w83795_read(client, IN_LSB_REG(i, IN_MAX)); |
| data->in_lsb[i][IN_LOW] = |
| w83795_read(client, IN_LSB_REG(i, IN_LOW)); |
| } |
| data->has_gain = w83795_read(client, W83795_REG_VMIGB_CTRL) & 0x0f; |
| |
| /* First update fan and limits */ |
| for (i = 0; i < ARRAY_SIZE(data->fan); i++) { |
| if (!(data->has_fan & (1 << i))) |
| continue; |
| data->fan_min[i] = |
| w83795_read(client, W83795_REG_FAN_MIN_HL(i)) << 4; |
| data->fan_min[i] |= |
| (w83795_read(client, W83795_REG_FAN_MIN_LSB(i) >> |
| W83795_REG_FAN_MIN_LSB_SHIFT(i))) & 0x0F; |
| data->fan[i] = w83795_read(client, W83795_REG_FAN(i)) << 4; |
| data->fan[i] |= |
| (w83795_read(client, W83795_REG_VRLSB >> 4)) & 0x0F; |
| } |
| |
| /* temperature and limits */ |
| for (i = 0; i < ARRAY_SIZE(data->temp); i++) { |
| if (!(data->has_temp & (1 << i))) |
| continue; |
| data->temp[i][TEMP_CRIT] = |
| w83795_read(client, W83795_REG_TEMP[i][TEMP_CRIT]); |
| data->temp[i][TEMP_CRIT_HYST] = |
| w83795_read(client, W83795_REG_TEMP[i][TEMP_CRIT_HYST]); |
| data->temp[i][TEMP_WARN] = |
| w83795_read(client, W83795_REG_TEMP[i][TEMP_WARN]); |
| data->temp[i][TEMP_WARN_HYST] = |
| w83795_read(client, W83795_REG_TEMP[i][TEMP_WARN_HYST]); |
| data->temp[i][TEMP_READ] = |
| w83795_read(client, W83795_REG_TEMP[i][TEMP_READ]); |
| data->temp_read_vrlsb[i] = |
| w83795_read(client, W83795_REG_VRLSB); |
| } |
| |
| /* dts temperature and limits */ |
| if (data->enable_dts != 0) { |
| data->dts_ext[DTS_CRIT] = |
| w83795_read(client, W83795_REG_DTS_EXT(DTS_CRIT)); |
| data->dts_ext[DTS_CRIT_HYST] = |
| w83795_read(client, W83795_REG_DTS_EXT(DTS_CRIT_HYST)); |
| data->dts_ext[DTS_WARN] = |
| w83795_read(client, W83795_REG_DTS_EXT(DTS_WARN)); |
| data->dts_ext[DTS_WARN_HYST] = |
| w83795_read(client, W83795_REG_DTS_EXT(DTS_WARN_HYST)); |
| for (i = 0; i < ARRAY_SIZE(data->dts); i++) { |
| if (!(data->has_dts & (1 << i))) |
| continue; |
| data->dts[i] = w83795_read(client, W83795_REG_DTS(i)); |
| data->dts_read_vrlsb[i] = |
| w83795_read(client, W83795_REG_VRLSB); |
| } |
| } |
| |
| /* First update temp source selction */ |
| for (i = 0; i < 3; i++) |
| data->temp_src[i] = w83795_read(client, W83795_REG_TSS(i)); |
| |
| /* pwm and smart fan */ |
| if (data->chip_type == w83795g) |
| data->has_pwm = 8; |
| else |
| data->has_pwm = 2; |
| data->pwm_fcms[0] = w83795_read(client, W83795_REG_FCMS1); |
| data->pwm_fcms[1] = w83795_read(client, W83795_REG_FCMS2); |
| /* w83795adg only support pwm2-0 */ |
| for (i = 0; i < W83795_REG_TEMP_NUM; i++) |
| data->pwm_tfmr[i] = w83795_read(client, W83795_REG_TFMR(i)); |
| data->pwm_fomc = w83795_read(client, W83795_REG_FOMC); |
| for (i = 0; i < data->has_pwm; i++) { |
| for (tmp = 0; tmp < 5; tmp++) { |
| data->pwm[i][tmp] = |
| w83795_read(client, W83795_REG_PWM(i, tmp)); |
| } |
| } |
| for (i = 0; i < 8; i++) { |
| data->target_speed[i] = |
| w83795_read(client, W83795_REG_FTSH(i)) << 4; |
| data->target_speed[i] |= |
| w83795_read(client, W83795_REG_FTSL(i)) >> 4; |
| } |
| data->tol_speed = w83795_read(client, W83795_REG_TFTS) & 0x3f; |
| |
| for (i = 0; i < W83795_REG_TEMP_NUM; i++) { |
| data->pwm_temp[i][TEMP_PWM_TTTI] = |
| w83795_read(client, W83795_REG_TTTI(i)) & 0x7f; |
| data->pwm_temp[i][TEMP_PWM_CTFS] = |
| w83795_read(client, W83795_REG_CTFS(i)); |
| tmp = w83795_read(client, W83795_REG_HT(i)); |
| data->pwm_temp[i][TEMP_PWM_HCT] = (tmp >> 4) & 0x0f; |
| data->pwm_temp[i][TEMP_PWM_HOT] = tmp & 0x0f; |
| } |
| for (i = 0; i < W83795_REG_TEMP_NUM; i++) { |
| for (tmp = 0; tmp < 7; tmp++) { |
| data->sf4_reg[i][SF4_TEMP][tmp] = |
| w83795_read(client, |
| W83795_REG_SF4_TEMP(i, tmp)); |
| data->sf4_reg[i][SF4_PWM][tmp] = |
| w83795_read(client, W83795_REG_SF4_PWM(i, tmp)); |
| } |
| } |
| |
| /* Setup PWM Register */ |
| for (i = 0; i < 3; i++) { |
| data->setup_pwm[i] = |
| w83795_read(client, W83795_REG_SETUP_PWM(i)); |
| } |
| |
| /* alarm and beep */ |
| for (i = 0; i < ALARM_BEEP_REG_NUM; i++) { |
| data->alarms[i] = w83795_read(client, W83795_REG_ALARM(i)); |
| data->beeps[i] = w83795_read(client, W83795_REG_BEEP(i)); |
| } |
| data->beep_enable = |
| (w83795_read(client, W83795_REG_BEEP(5)) >> 7) & 0x01; |
| |
| /* Register sysfs hooks */ |
| for (i = 0; i < ARRAY_SIZE(w83795_in); i++) { |
| if (!(data->has_in & (1 << (i / 6)))) |
| continue; |
| err = device_create_file(dev, &w83795_in[i].dev_attr); |
| if (err) |
| goto exit_remove; |
| } |
| |
| for (i = 0; i < ARRAY_SIZE(w83795_fan); i++) { |
| if (!(data->has_fan & (1 << (i / 5)))) |
| continue; |
| err = device_create_file(dev, &w83795_fan[i].dev_attr); |
| if (err) |
| goto exit_remove; |
| } |
| |
| for (i = 0; i < ARRAY_SIZE(sda_single_files); i++) { |
| err = device_create_file(dev, &sda_single_files[i].dev_attr); |
| if (err) |
| goto exit_remove; |
| } |
| |
| for (i = 0; i < ARRAY_SIZE(w83795_temp); i++) { |
| if (!(data->has_temp & (1 << (i / 29)))) |
| continue; |
| err = device_create_file(dev, &w83795_temp[i].dev_attr); |
| if (err) |
| goto exit_remove; |
| } |
| |
| if (data->enable_dts != 0) { |
| for (i = 0; i < ARRAY_SIZE(w83795_dts); i++) { |
| if (!(data->has_dts & (1 << (i / 8)))) |
| continue; |
| err = device_create_file(dev, &w83795_dts[i].dev_attr); |
| if (err) |
| goto exit_remove; |
| } |
| } |
| |
| if (data->chip_type == w83795g) { |
| for (i = 0; i < ARRAY_SIZE(w83795_left_reg); i++) { |
| err = device_create_file(dev, |
| &w83795_left_reg[i].dev_attr); |
| if (err) |
| goto exit_remove; |
| } |
| } |
| |
| for (i = 0; i < ARRAY_SIZE(w83795_static); i++) { |
| err = device_create_file(dev, &w83795_static[i].dev_attr); |
| if (err) |
| goto exit_remove; |
| } |
| |
| data->hwmon_dev = hwmon_device_register(dev); |
| if (IS_ERR(data->hwmon_dev)) { |
| err = PTR_ERR(data->hwmon_dev); |
| goto exit_remove; |
| } |
| |
| return 0; |
| |
| /* Unregister sysfs hooks */ |
| exit_remove: |
| for (i = 0; i < ARRAY_SIZE(w83795_in); i++) |
| device_remove_file(dev, &w83795_in[i].dev_attr); |
| |
| for (i = 0; i < ARRAY_SIZE(w83795_fan); i++) |
| device_remove_file(dev, &w83795_fan[i].dev_attr); |
| |
| for (i = 0; i < ARRAY_SIZE(sda_single_files); i++) |
| device_remove_file(dev, &sda_single_files[i].dev_attr); |
| |
| if (data->chip_type == w83795g) { |
| for (i = 0; i < ARRAY_SIZE(w83795_left_reg); i++) |
| device_remove_file(dev, &w83795_left_reg[i].dev_attr); |
| } |
| |
| for (i = 0; i < ARRAY_SIZE(w83795_temp); i++) |
| device_remove_file(dev, &w83795_temp[i].dev_attr); |
| |
| for (i = 0; i < ARRAY_SIZE(w83795_dts); i++) |
| device_remove_file(dev, &w83795_dts[i].dev_attr); |
| |
| for (i = 0; i < ARRAY_SIZE(w83795_static); i++) |
| device_remove_file(dev, &w83795_static[i].dev_attr); |
| |
| kfree(data); |
| exit: |
| return err; |
| } |
| |
| static int w83795_remove(struct i2c_client *client) |
| { |
| struct w83795_data *data = i2c_get_clientdata(client); |
| struct device *dev = &client->dev; |
| int i; |
| |
| hwmon_device_unregister(data->hwmon_dev); |
| |
| for (i = 0; i < ARRAY_SIZE(w83795_in); i++) |
| device_remove_file(dev, &w83795_in[i].dev_attr); |
| |
| for (i = 0; i < ARRAY_SIZE(w83795_fan); i++) |
| device_remove_file(dev, &w83795_fan[i].dev_attr); |
| |
| for (i = 0; i < ARRAY_SIZE(sda_single_files); i++) |
| device_remove_file(dev, &sda_single_files[i].dev_attr); |
| |
| if (data->chip_type == w83795g) { |
| for (i = 0; i < ARRAY_SIZE(w83795_left_reg); i++) |
| device_remove_file(dev, &w83795_left_reg[i].dev_attr); |
| } |
| |
| for (i = 0; i < ARRAY_SIZE(w83795_temp); i++) |
| device_remove_file(dev, &w83795_temp[i].dev_attr); |
| |
| for (i = 0; i < ARRAY_SIZE(w83795_dts); i++) |
| device_remove_file(dev, &w83795_dts[i].dev_attr); |
| |
| for (i = 0; i < ARRAY_SIZE(w83795_static); i++) |
| device_remove_file(dev, &w83795_static[i].dev_attr); |
| |
| kfree(data); |
| |
| return 0; |
| } |
| |
| |
| static const struct i2c_device_id w83795_id[] = { |
| { "w83795", w83795 }, |
| { } |
| }; |
| MODULE_DEVICE_TABLE(i2c, w83795_id); |
| |
| static struct i2c_driver w83795_driver = { |
| .driver = { |
| .name = "w83795", |
| }, |
| .probe = w83795_probe, |
| .remove = w83795_remove, |
| .id_table = w83795_id, |
| |
| .class = I2C_CLASS_HWMON, |
| .detect = w83795_detect, |
| .address_list = normal_i2c, |
| }; |
| |
| static int __init sensors_w83795_init(void) |
| { |
| return i2c_add_driver(&w83795_driver); |
| } |
| |
| static void __exit sensors_w83795_exit(void) |
| { |
| i2c_del_driver(&w83795_driver); |
| } |
| |
| MODULE_AUTHOR("Wei Song"); |
| MODULE_DESCRIPTION("W83795G/ADG hardware monitoring driver"); |
| MODULE_LICENSE("GPL"); |
| |
| module_init(sensors_w83795_init); |
| module_exit(sensors_w83795_exit); |