powerpc/powernv: Reserve the correct PE number
We're assigning PE numbers after the completion of PCI probe. During
the PCI probe, we had PE#0 as the super container to encompass all
PCI devices. However, that's inappropriate since PELTM has ascending
order of priority on search on P7IOC. So we need PE#127 takes the
role that PE#0 has previously. For PHB3, we still have PE#0 as the
reserved PE.
The patch supposes that the underly firmware has built the RID to
PE# mapping after resetting IODA tables: all PELTM entries except
last one has invalid mapping on P7IOC, but all RTEs have binding
to PE#0. The reserved PE# is being exported by firmware by device
tree.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
diff --git a/arch/powerpc/platforms/powernv/pci-ioda.c b/arch/powerpc/platforms/powernv/pci-ioda.c
index 198566e..084cdfa 100644
--- a/arch/powerpc/platforms/powernv/pci-ioda.c
+++ b/arch/powerpc/platforms/powernv/pci-ioda.c
@@ -1209,12 +1209,13 @@
pr_err(" Failed to map registers !\n");
/* Initialize more IODA stuff */
+ phb->ioda.total_pe = 1;
prop32 = of_get_property(np, "ibm,opal-num-pes", NULL);
- if (!prop32)
- phb->ioda.total_pe = 1;
- else
+ if (prop32)
phb->ioda.total_pe = be32_to_cpup(prop32);
-
+ prop32 = of_get_property(np, "ibm,opal-reserved-pe", NULL);
+ if (prop32)
+ phb->ioda.reserved_pe = be32_to_cpup(prop32);
phb->ioda.m32_size = resource_size(&hose->mem_resources[0]);
/* FW Has already off top 64k of M32 space (MSI space) */
phb->ioda.m32_size += 0x10000;
@@ -1243,7 +1244,7 @@
if (phb->type == PNV_PHB_IODA1)
phb->ioda.io_segmap = aux + iomap_off;
phb->ioda.pe_array = aux + pemap_off;
- set_bit(0, phb->ioda.pe_alloc);
+ set_bit(phb->ioda.reserved_pe, phb->ioda.pe_alloc);
INIT_LIST_HEAD(&phb->ioda.pe_dma_list);
INIT_LIST_HEAD(&phb->ioda.pe_list);
@@ -1268,8 +1269,10 @@
segment_size);
#endif
- pr_info(" %d PE's M32: 0x%x [segment=0x%x] IO: 0x%x [segment=0x%x]\n",
+ pr_info(" %d (%d) PE's M32: 0x%x [segment=0x%x]"
+ " IO: 0x%x [segment=0x%x]\n",
phb->ioda.total_pe,
+ phb->ioda.reserved_pe,
phb->ioda.m32_size, phb->ioda.m32_segsize,
phb->ioda.io_size, phb->ioda.io_segsize);
@@ -1306,13 +1309,6 @@
rc = opal_pci_reset(phb_id, OPAL_PCI_IODA_TABLE_RESET, OPAL_ASSERT_RESET);
if (rc)
pr_warning(" OPAL Error %ld performing IODA table reset !\n", rc);
-
- /*
- * On IODA1 map everything to PE#0, on IODA2 we assume the IODA reset
- * has cleared the RTT which has the same effect
- */
- if (ioda_type == PNV_PHB_IODA1)
- opal_pci_set_pe(phb_id, 0, 0, 7, 1, 1 , OPAL_MAP_PE);
}
void __init pnv_pci_init_ioda2_phb(struct device_node *np)