[media] cx23885: Add si2165 support for HVR-5500
The same card entry is used for HVR-4400 and HVR-5500.
Only HVR-5500 has been tested.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
diff --git a/drivers/media/pci/cx23885/cx23885-dvb.c b/drivers/media/pci/cx23885/cx23885-dvb.c
index 6968706..968fecc 100644
--- a/drivers/media/pci/cx23885/cx23885-dvb.c
+++ b/drivers/media/pci/cx23885/cx23885-dvb.c
@@ -72,6 +72,7 @@
#include "tda10071.h"
#include "a8293.h"
#include "mb86a20s.h"
+#include "si2165.h"
static unsigned int debug;
@@ -303,6 +304,11 @@
.output_opt = TDA18271_OUTPUT_LT_OFF,
};
+static struct tda18271_config hauppauge_hvr4400_tuner_config = {
+ .gate = TDA18271_GATE_DIGITAL,
+ .output_opt = TDA18271_OUTPUT_LT_OFF,
+};
+
static struct tda18271_std_map hauppauge_hvr127x_std_map = {
.atsc_6 = { .if_freq = 3250, .agc_mode = 3, .std = 4,
.if_lvl = 1, .rfagc_top = 0x58 },
@@ -703,6 +709,12 @@
.i2c_addr = 0x0b,
};
+static const struct si2165_config hauppauge_hvr4400_si2165_config = {
+ .i2c_addr = 0x64,
+ .chip_mode = SI2165_MODE_PLL_XTAL,
+ .ref_freq_Hz = 16000000,
+};
+
static int netup_altera_fpga_rw(void *device, int flag, int data, int read)
{
struct cx23885_dev *dev = (struct cx23885_dev *)device;
@@ -1459,13 +1471,34 @@
break;
case CX23885_BOARD_HAUPPAUGE_HVR4400:
i2c_bus = &dev->i2c_bus[0];
- fe0->dvb.frontend = dvb_attach(tda10071_attach,
+ i2c_bus2 = &dev->i2c_bus[1];
+ switch (port->nr) {
+ /* port b */
+ case 1:
+ fe0->dvb.frontend = dvb_attach(tda10071_attach,
&hauppauge_tda10071_config,
&i2c_bus->i2c_adap);
- if (fe0->dvb.frontend != NULL) {
- dvb_attach(a8293_attach, fe0->dvb.frontend,
- &i2c_bus->i2c_adap,
- &hauppauge_a8293_config);
+ if (fe0->dvb.frontend != NULL) {
+ if (!dvb_attach(a8293_attach, fe0->dvb.frontend,
+ &i2c_bus->i2c_adap,
+ &hauppauge_a8293_config))
+ goto frontend_detach;
+ }
+ break;
+ /* port c */
+ case 2:
+ fe0->dvb.frontend = dvb_attach(si2165_attach,
+ &hauppauge_hvr4400_si2165_config,
+ &i2c_bus->i2c_adap);
+ if (fe0->dvb.frontend != NULL) {
+ fe0->dvb.frontend->ops.i2c_gate_ctrl = 0;
+ if (!dvb_attach(tda18271_attach,
+ fe0->dvb.frontend,
+ 0x60, &i2c_bus2->i2c_adap,
+ &hauppauge_hvr4400_tuner_config))
+ goto frontend_detach;
+ }
+ break;
}
break;
default: