brcmfmac: assure device is ready for download after brcmf_chip_attach()
Make the brcmf_chip_attach() function responsible for putting the
device in a state where it is accessible for firmware download.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
diff --git a/drivers/net/wireless/brcm80211/brcmfmac/chip.c b/drivers/net/wireless/brcm80211/brcmfmac/chip.c
index d68e37d..c11137e 100644
--- a/drivers/net/wireless/brcm80211/brcmfmac/chip.c
+++ b/drivers/net/wireless/brcm80211/brcmfmac/chip.c
@@ -786,12 +786,6 @@
if (chip->ops->setup)
ret = chip->ops->setup(chip->ctx, pub);
- /*
- * Make sure any on-chip ARM is off (in case strapping is wrong),
- * or downloaded code was already running.
- */
- brcmf_chip_disable_arm(chip, BCMA_CORE_ARM_CM3);
- brcmf_chip_disable_arm(chip, BCMA_CORE_ARM_CR4);
return ret;
}
@@ -833,6 +827,8 @@
if (err < 0)
goto fail;
+ /* assure chip is passive for download */
+ brcmf_chip_set_passive(&chip->pub);
return &chip->pub;
fail:
diff --git a/drivers/net/wireless/brcm80211/brcmfmac/pcie.c b/drivers/net/wireless/brcm80211/brcmfmac/pcie.c
index 81e544f..aa7a4df 100644
--- a/drivers/net/wireless/brcm80211/brcmfmac/pcie.c
+++ b/drivers/net/wireless/brcm80211/brcmfmac/pcie.c
@@ -509,8 +509,6 @@
static int brcmf_pcie_enter_download_state(struct brcmf_pciedev_info *devinfo)
{
- brcmf_chip_set_passive(devinfo->ci);
-
if (devinfo->ci->chip == BRCM_CC_43602_CHIP_ID) {
brcmf_pcie_select_core(devinfo, BCMA_CORE_ARM_CR4);
brcmf_pcie_write_reg32(devinfo, BRCMF_PCIE_ARMCR4REG_BANKIDX,
diff --git a/drivers/net/wireless/brcm80211/brcmfmac/sdio.c b/drivers/net/wireless/brcm80211/brcmfmac/sdio.c
index fff3b26..c783c25 100644
--- a/drivers/net/wireless/brcm80211/brcmfmac/sdio.c
+++ b/drivers/net/wireless/brcm80211/brcmfmac/sdio.c
@@ -3356,9 +3356,6 @@
sdio_claim_host(bus->sdiodev->func[1]);
brcmf_sdio_clkctl(bus, CLK_AVAIL, false);
- /* Keep arm in reset */
- brcmf_chip_set_passive(bus->ci);
-
rstvec = get_unaligned_le32(fw->data);
brcmf_dbg(SDIO, "firmware rstvec: %x\n", rstvec);