ab8500_bm: Skip first CCEOC irq for instant current
When enabling the CCEOC irq we might get false interrupt
from ab8500-driver due to the latched value will be saved
and interpreted as an IRQ when enabled
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Johan Bjornstedt <johan.bjornstedt@stericsson.com>
Signed-off-by: Henrik Solver <henrik.solver@stericsson.com>
Reviewed-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
diff --git a/drivers/power/ab8500_btemp.c b/drivers/power/ab8500_btemp.c
index e1d2803..4a570b6 100644
--- a/drivers/power/ab8500_btemp.c
+++ b/drivers/power/ab8500_btemp.c
@@ -374,13 +374,10 @@
return ret;
}
- /*
- * Since there is no interrupt when current measurement is done,
- * loop for over 250ms (250ms is one sample conversion time
- * with 32.768 Khz RTC clock). Note that a stop time must be set
- * since the ab8500_btemp_read_batctrl_voltage call can block and
- * take an unknown amount of time to complete.
- */
+ do {
+ msleep(20);
+ } while (!ab8500_fg_inst_curr_started(di->fg));
+
i = 0;
do {
diff --git a/drivers/power/ab8500_fg.c b/drivers/power/ab8500_fg.c
index 3d05c73..0f40c96 100644
--- a/drivers/power/ab8500_fg.c
+++ b/drivers/power/ab8500_fg.c
@@ -160,6 +160,7 @@
* @recovery_cnt: Counter for recovery mode
* @high_curr_cnt: Counter for high current mode
* @init_cnt: Counter for init mode
+ * @nbr_cceoc_irq_cnt Counter for number of CCEOC irqs received since enabled
* @recovery_needed: Indicate if recovery is needed
* @high_curr_mode: Indicate if we're in high current mode
* @init_capacity: Indicate if initial capacity measuring should be done
@@ -167,6 +168,7 @@
* @calib_state State during offset calibration
* @discharge_state: Current discharge state
* @charge_state: Current charge state
+ * @ab8500_fg_started Completion struct used for the instant current start
* @ab8500_fg_complete Completion struct used for the instant current reading
* @flags: Structure for information about events triggered
* @bat_cap: Structure for battery capacity specific parameters
@@ -199,6 +201,7 @@
int recovery_cnt;
int high_curr_cnt;
int init_cnt;
+ int nbr_cceoc_irq_cnt;
bool recovery_needed;
bool high_curr_mode;
bool init_capacity;
@@ -206,6 +209,7 @@
enum ab8500_fg_calibration_state calib_state;
enum ab8500_fg_discharge_state discharge_state;
enum ab8500_fg_charge_state charge_state;
+ struct completion ab8500_fg_started;
struct completion ab8500_fg_complete;
struct ab8500_fg_flags flags;
struct ab8500_fg_battery_capacity bat_cap;
@@ -524,13 +528,14 @@
* Note: This is part "one" and has to be called before
* ab8500_fg_inst_curr_finalize()
*/
- int ab8500_fg_inst_curr_start(struct ab8500_fg *di)
+int ab8500_fg_inst_curr_start(struct ab8500_fg *di)
{
u8 reg_val;
int ret;
mutex_lock(&di->cc_lock);
+ di->nbr_cceoc_irq_cnt = 0;
ret = abx500_get_register_interruptible(di->dev, AB8500_RTC,
AB8500_RTC_CC_CONF_REG, ®_val);
if (ret < 0)
@@ -558,6 +563,7 @@
}
/* Return and WFI */
+ INIT_COMPLETION(di->ab8500_fg_started);
INIT_COMPLETION(di->ab8500_fg_complete);
enable_irq(di->irq);
@@ -569,6 +575,17 @@
}
/**
+ * ab8500_fg_inst_curr_started() - check if fg conversion has started
+ * @di: pointer to the ab8500_fg structure
+ *
+ * Returns 1 if conversion started, 0 if still waiting
+ */
+int ab8500_fg_inst_curr_started(struct ab8500_fg *di)
+{
+ return completion_done(&di->ab8500_fg_started);
+}
+
+/**
* ab8500_fg_inst_curr_done() - check if fg conversion is done
* @di: pointer to the ab8500_fg structure
*
@@ -596,13 +613,15 @@
int timeout;
if (!completion_done(&di->ab8500_fg_complete)) {
- timeout = wait_for_completion_timeout(&di->ab8500_fg_complete,
+ timeout = wait_for_completion_timeout(
+ &di->ab8500_fg_complete,
INS_CURR_TIMEOUT);
dev_dbg(di->dev, "Finalize time: %d ms\n",
((INS_CURR_TIMEOUT - timeout) * 1000) / HZ);
if (!timeout) {
ret = -ETIME;
disable_irq(di->irq);
+ di->nbr_cceoc_irq_cnt = 0;
dev_err(di->dev, "completion timed out [%d]\n",
__LINE__);
goto fail;
@@ -610,6 +629,7 @@
}
disable_irq(di->irq);
+ di->nbr_cceoc_irq_cnt = 0;
ret = abx500_mask_and_set_register_interruptible(di->dev,
AB8500_GAS_GAUGE, AB8500_GASG_CC_CTRL_REG,
@@ -684,6 +704,7 @@
int ab8500_fg_inst_curr_blocking(struct ab8500_fg *di)
{
int ret;
+ int timeout;
int res = 0;
ret = ab8500_fg_inst_curr_start(di);
@@ -692,13 +713,32 @@
return 0;
}
+ /* Wait for CC to actually start */
+ if (!completion_done(&di->ab8500_fg_started)) {
+ timeout = wait_for_completion_timeout(
+ &di->ab8500_fg_started,
+ INS_CURR_TIMEOUT);
+ dev_dbg(di->dev, "Start time: %d ms\n",
+ ((INS_CURR_TIMEOUT - timeout) * 1000) / HZ);
+ if (!timeout) {
+ ret = -ETIME;
+ dev_err(di->dev, "completion timed out [%d]\n",
+ __LINE__);
+ goto fail;
+ }
+ }
+
ret = ab8500_fg_inst_curr_finalize(di, &res);
if (ret) {
dev_err(di->dev, "Failed to finalize fg_inst\n");
return 0;
}
+ dev_dbg(di->dev, "%s instant current: %d", __func__, res);
return res;
+fail:
+ mutex_unlock(&di->cc_lock);
+ return ret;
}
/**
@@ -1523,8 +1563,6 @@
case AB8500_FG_DISCHARGE_WAKEUP:
ab8500_fg_coulomb_counter(di, true);
- di->inst_curr = ab8500_fg_inst_curr_blocking(di);
-
ab8500_fg_calc_cap_discharge_voltage(di, true);
di->fg_samples = SEC_TO_SAMPLE(
@@ -1641,8 +1679,6 @@
fg_periodic_work.work);
if (di->init_capacity) {
- /* A dummy read that will return 0 */
- di->inst_curr = ab8500_fg_inst_curr_blocking(di);
/* Get an initial capacity calculation */
ab8500_fg_calc_cap_discharge_voltage(di, true);
ab8500_fg_check_capacity_limits(di, true);
@@ -1828,7 +1864,13 @@
static irqreturn_t ab8500_fg_cc_data_end_handler(int irq, void *_di)
{
struct ab8500_fg *di = _di;
- complete(&di->ab8500_fg_complete);
+ if (!di->nbr_cceoc_irq_cnt) {
+ di->nbr_cceoc_irq_cnt++;
+ complete(&di->ab8500_fg_started);
+ } else {
+ di->nbr_cceoc_irq_cnt = 0;
+ complete(&di->ab8500_fg_complete);
+ }
return IRQ_HANDLED;
}
@@ -2551,7 +2593,11 @@
di->fg_samples = SEC_TO_SAMPLE(di->bm->fg_params->init_timer);
ab8500_fg_coulomb_counter(di, true);
- /* Initialize completion used to notify completion of inst current */
+ /*
+ * Initialize completion used to notify completion and start
+ * of inst current
+ */
+ init_completion(&di->ab8500_fg_started);
init_completion(&di->ab8500_fg_complete);
/* Register interrupts */
@@ -2571,6 +2617,7 @@
}
di->irq = platform_get_irq_byname(pdev, "CCEOC");
disable_irq(di->irq);
+ di->nbr_cceoc_irq_cnt = 0;
platform_set_drvdata(pdev, di);