ide: use ATA_* defines instead of *_STAT and *_ERR ones
* ERR_STAT -> ATA_ERR
* INDEX_STAT -> ATA_IDX
* ECC_STAT -> ATA_CORR
* DRQ_STAT -> ATA_DRQ
* SEEK_STAT -> ATA_DSC
* WRERR_STAT -> ATA_DF
* READY_STAT -> ATA_DRDY
* BUSY_STAT -> ATA_BUSY
* MARK_ERR -> ATA_AMNF
* TRK0_ERR -> ATA_TRK0NF
* ABRT_ERR -> ATA_ABORTED
* MCR_ERR -> ATA_MCR
* ID_ERR -> ATA_IDNF
* MC_ERR -> ATA_MC
* ECC_ERR -> ATA_UNC
* ICRC_ERR -> ATA_ICRC
* BBD_ERR -> ATA_BBK
Also:
* ILI_ERR -> ATAPI_ILI
* EOM_ERR -> ATAPI_EOM
* LFS_ERR -> ATAPI_LFS
* CD -> ATAPI_COD
* IO -> ATAPI_IO
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
diff --git a/drivers/ide/ide-iops.c b/drivers/ide/ide-iops.c
index 21647a2..8cfa612 100644
--- a/drivers/ide/ide-iops.c
+++ b/drivers/ide/ide-iops.c
@@ -473,7 +473,7 @@
/* Note: this may clear a pending IRQ!! */
stat = hwif->tp_ops->read_status(hwif);
- if (stat & BUSY_STAT)
+ if (stat & ATA_BUSY)
/* drive busy: definitely not interrupting */
return 0;
@@ -505,10 +505,10 @@
udelay(1); /* spec allows drive 400ns to assert "BUSY" */
stat = tp_ops->read_status(hwif);
- if (stat & BUSY_STAT) {
+ if (stat & ATA_BUSY) {
local_irq_set(flags);
timeout += jiffies;
- while ((stat = tp_ops->read_status(hwif)) & BUSY_STAT) {
+ while ((stat = tp_ops->read_status(hwif)) & ATA_BUSY) {
if (time_after(jiffies, timeout)) {
/*
* One last read after the timeout in case
@@ -516,7 +516,7 @@
* progress during the timeout..
*/
stat = tp_ops->read_status(hwif);
- if (!(stat & BUSY_STAT))
+ if ((stat & ATA_BUSY) == 0)
break;
local_irq_restore(flags);
@@ -685,12 +685,12 @@
msleep(50); /* give drive a breather */
stat = tp_ops->read_altstatus(hwif);
- } while (stat & BUSY_STAT);
+ } while (stat & ATA_BUSY);
- msleep(50); /* wait for IRQ and DRQ_STAT */
+ msleep(50); /* wait for IRQ and ATA_DRQ */
stat = tp_ops->read_status(hwif);
- if (!OK_STAT(stat, DRQ_STAT, BAD_R_STAT)) {
+ if (!OK_STAT(stat, ATA_DRQ, BAD_R_STAT)) {
SELECT_MASK(drive, 0);
printk("%s: CHECK for good STATUS\n", drive->name);
return 0;
@@ -776,7 +776,7 @@
tp_ops->set_irq(hwif, 1);
error = __ide_wait_stat(drive, drive->ready_stat,
- BUSY_STAT|DRQ_STAT|ERR_STAT,
+ ATA_BUSY | ATA_DRQ | ATA_ERR,
WAIT_CMD, &stat);
SELECT_MASK(drive, 0);
@@ -923,7 +923,7 @@
udelay (10);
stat = hwif->tp_ops->read_status(hwif);
- if (OK_STAT(stat, 0, BUSY_STAT))
+ if (OK_STAT(stat, 0, ATA_BUSY))
printk("%s: ATAPI reset complete\n", drive->name);
else {
if (time_before(jiffies, hwgroup->poll_timeout)) {
@@ -969,7 +969,7 @@
tmp = hwif->tp_ops->read_status(hwif);
- if (!OK_STAT(tmp, 0, BUSY_STAT)) {
+ if (!OK_STAT(tmp, 0, ATA_BUSY)) {
if (time_before(jiffies, hwgroup->poll_timeout)) {
ide_set_handler(drive, &reset_pollfunc, HZ/20, NULL);
/* continue polling */
@@ -1183,7 +1183,7 @@
*/
mdelay(1);
stat = hwif->tp_ops->read_status(hwif);
- if ((stat & BUSY_STAT) == 0)
+ if ((stat & ATA_BUSY) == 0)
return 0;
/*
* Assume a value of 0xff means nothing is connected to