| /* |
| * Copyright (C) Freescale Semicondutor, Inc. 2006-2010. All rights reserved. |
| * |
| * Author: Andy Fleming <afleming@freescale.com> |
| * |
| * Based on 83xx/mpc8360e_pb.c by: |
| * Li Yang <LeoLi@freescale.com> |
| * Yin Olivia <Hong-hua.Yin@freescale.com> |
| * |
| * Description: |
| * MPC85xx MDS board specific routines. |
| * |
| * This program is free software; you can redistribute it and/or modify it |
| * under the terms of the GNU General Public License as published by the |
| * Free Software Foundation; either version 2 of the License, or (at your |
| * option) any later version. |
| */ |
| |
| #include <linux/stddef.h> |
| #include <linux/kernel.h> |
| #include <linux/init.h> |
| #include <linux/errno.h> |
| #include <linux/reboot.h> |
| #include <linux/pci.h> |
| #include <linux/kdev_t.h> |
| #include <linux/major.h> |
| #include <linux/console.h> |
| #include <linux/delay.h> |
| #include <linux/seq_file.h> |
| #include <linux/initrd.h> |
| #include <linux/module.h> |
| #include <linux/fsl_devices.h> |
| #include <linux/of_platform.h> |
| #include <linux/of_device.h> |
| #include <linux/phy.h> |
| #include <linux/memblock.h> |
| |
| #include <asm/system.h> |
| #include <asm/atomic.h> |
| #include <asm/time.h> |
| #include <asm/io.h> |
| #include <asm/machdep.h> |
| #include <asm/pci-bridge.h> |
| #include <asm/irq.h> |
| #include <mm/mmu_decl.h> |
| #include <asm/prom.h> |
| #include <asm/udbg.h> |
| #include <sysdev/fsl_soc.h> |
| #include <sysdev/fsl_pci.h> |
| #include <sysdev/simple_gpio.h> |
| #include <asm/qe.h> |
| #include <asm/qe_ic.h> |
| #include <asm/mpic.h> |
| #include <asm/swiotlb.h> |
| |
| #undef DEBUG |
| #ifdef DEBUG |
| #define DBG(fmt...) udbg_printf(fmt) |
| #else |
| #define DBG(fmt...) |
| #endif |
| |
| #define MV88E1111_SCR 0x10 |
| #define MV88E1111_SCR_125CLK 0x0010 |
| static int mpc8568_fixup_125_clock(struct phy_device *phydev) |
| { |
| int scr; |
| int err; |
| |
| /* Workaround for the 125 CLK Toggle */ |
| scr = phy_read(phydev, MV88E1111_SCR); |
| |
| if (scr < 0) |
| return scr; |
| |
| err = phy_write(phydev, MV88E1111_SCR, scr & ~(MV88E1111_SCR_125CLK)); |
| |
| if (err) |
| return err; |
| |
| err = phy_write(phydev, MII_BMCR, BMCR_RESET); |
| |
| if (err) |
| return err; |
| |
| scr = phy_read(phydev, MV88E1111_SCR); |
| |
| if (scr < 0) |
| return scr; |
| |
| err = phy_write(phydev, MV88E1111_SCR, scr | 0x0008); |
| |
| return err; |
| } |
| |
| static int mpc8568_mds_phy_fixups(struct phy_device *phydev) |
| { |
| int temp; |
| int err; |
| |
| /* Errata */ |
| err = phy_write(phydev,29, 0x0006); |
| |
| if (err) |
| return err; |
| |
| temp = phy_read(phydev, 30); |
| |
| if (temp < 0) |
| return temp; |
| |
| temp = (temp & (~0x8000)) | 0x4000; |
| err = phy_write(phydev,30, temp); |
| |
| if (err) |
| return err; |
| |
| err = phy_write(phydev,29, 0x000a); |
| |
| if (err) |
| return err; |
| |
| temp = phy_read(phydev, 30); |
| |
| if (temp < 0) |
| return temp; |
| |
| temp = phy_read(phydev, 30); |
| |
| if (temp < 0) |
| return temp; |
| |
| temp &= ~0x0020; |
| |
| err = phy_write(phydev,30,temp); |
| |
| if (err) |
| return err; |
| |
| /* Disable automatic MDI/MDIX selection */ |
| temp = phy_read(phydev, 16); |
| |
| if (temp < 0) |
| return temp; |
| |
| temp &= ~0x0060; |
| err = phy_write(phydev,16,temp); |
| |
| return err; |
| } |
| |
| /* ************************************************************************ |
| * |
| * Setup the architecture |
| * |
| */ |
| #ifdef CONFIG_SMP |
| extern void __init mpc85xx_smp_init(void); |
| #endif |
| |
| #ifdef CONFIG_QUICC_ENGINE |
| static struct of_device_id mpc85xx_qe_ids[] __initdata = { |
| { .type = "qe", }, |
| { .compatible = "fsl,qe", }, |
| { }, |
| }; |
| |
| static void __init mpc85xx_publish_qe_devices(void) |
| { |
| struct device_node *np; |
| |
| np = of_find_compatible_node(NULL, NULL, "fsl,qe"); |
| if (!of_device_is_available(np)) { |
| of_node_put(np); |
| return; |
| } |
| |
| of_platform_bus_probe(NULL, mpc85xx_qe_ids, NULL); |
| } |
| |
| static void __init mpc85xx_mds_reset_ucc_phys(void) |
| { |
| struct device_node *np; |
| static u8 __iomem *bcsr_regs; |
| |
| /* Map BCSR area */ |
| np = of_find_node_by_name(NULL, "bcsr"); |
| if (!np) |
| return; |
| |
| bcsr_regs = of_iomap(np, 0); |
| of_node_put(np); |
| if (!bcsr_regs) |
| return; |
| |
| if (machine_is(mpc8568_mds)) { |
| #define BCSR_UCC1_GETH_EN (0x1 << 7) |
| #define BCSR_UCC2_GETH_EN (0x1 << 7) |
| #define BCSR_UCC1_MODE_MSK (0x3 << 4) |
| #define BCSR_UCC2_MODE_MSK (0x3 << 0) |
| |
| /* Turn off UCC1 & UCC2 */ |
| clrbits8(&bcsr_regs[8], BCSR_UCC1_GETH_EN); |
| clrbits8(&bcsr_regs[9], BCSR_UCC2_GETH_EN); |
| |
| /* Mode is RGMII, all bits clear */ |
| clrbits8(&bcsr_regs[11], BCSR_UCC1_MODE_MSK | |
| BCSR_UCC2_MODE_MSK); |
| |
| /* Turn UCC1 & UCC2 on */ |
| setbits8(&bcsr_regs[8], BCSR_UCC1_GETH_EN); |
| setbits8(&bcsr_regs[9], BCSR_UCC2_GETH_EN); |
| } else if (machine_is(mpc8569_mds)) { |
| #define BCSR7_UCC12_GETHnRST (0x1 << 2) |
| #define BCSR8_UEM_MARVELL_RST (0x1 << 1) |
| #define BCSR_UCC_RGMII (0x1 << 6) |
| #define BCSR_UCC_RTBI (0x1 << 5) |
| /* |
| * U-Boot mangles interrupt polarity for Marvell PHYs, |
| * so reset built-in and UEM Marvell PHYs, this puts |
| * the PHYs into their normal state. |
| */ |
| clrbits8(&bcsr_regs[7], BCSR7_UCC12_GETHnRST); |
| setbits8(&bcsr_regs[8], BCSR8_UEM_MARVELL_RST); |
| |
| setbits8(&bcsr_regs[7], BCSR7_UCC12_GETHnRST); |
| clrbits8(&bcsr_regs[8], BCSR8_UEM_MARVELL_RST); |
| |
| for (np = NULL; (np = of_find_compatible_node(np, |
| "network", |
| "ucc_geth")) != NULL;) { |
| const unsigned int *prop; |
| int ucc_num; |
| |
| prop = of_get_property(np, "cell-index", NULL); |
| if (prop == NULL) |
| continue; |
| |
| ucc_num = *prop - 1; |
| |
| prop = of_get_property(np, "phy-connection-type", NULL); |
| if (prop == NULL) |
| continue; |
| |
| if (strcmp("rtbi", (const char *)prop) == 0) |
| clrsetbits_8(&bcsr_regs[7 + ucc_num], |
| BCSR_UCC_RGMII, BCSR_UCC_RTBI); |
| } |
| } else if (machine_is(p1021_mds)) { |
| #define BCSR11_ENET_MICRST (0x1 << 5) |
| /* Reset Micrel PHY */ |
| clrbits8(&bcsr_regs[11], BCSR11_ENET_MICRST); |
| setbits8(&bcsr_regs[11], BCSR11_ENET_MICRST); |
| } |
| |
| iounmap(bcsr_regs); |
| } |
| |
| static void __init mpc85xx_mds_qe_init(void) |
| { |
| struct device_node *np; |
| |
| np = of_find_compatible_node(NULL, NULL, "fsl,qe"); |
| if (!np) { |
| np = of_find_node_by_name(NULL, "qe"); |
| if (!np) |
| return; |
| } |
| |
| if (!of_device_is_available(np)) { |
| of_node_put(np); |
| return; |
| } |
| |
| qe_reset(); |
| of_node_put(np); |
| |
| np = of_find_node_by_name(NULL, "par_io"); |
| if (np) { |
| struct device_node *ucc; |
| |
| par_io_init(np); |
| of_node_put(np); |
| |
| for_each_node_by_name(ucc, "ucc") |
| par_io_of_config(ucc); |
| } |
| |
| mpc85xx_mds_reset_ucc_phys(); |
| |
| if (machine_is(p1021_mds)) { |
| #define MPC85xx_PMUXCR_OFFSET 0x60 |
| #define MPC85xx_PMUXCR_QE0 0x00008000 |
| #define MPC85xx_PMUXCR_QE3 0x00001000 |
| #define MPC85xx_PMUXCR_QE9 0x00000040 |
| #define MPC85xx_PMUXCR_QE12 0x00000008 |
| static __be32 __iomem *pmuxcr; |
| |
| np = of_find_node_by_name(NULL, "global-utilities"); |
| |
| if (np) { |
| pmuxcr = of_iomap(np, 0) + MPC85xx_PMUXCR_OFFSET; |
| |
| if (!pmuxcr) |
| printk(KERN_EMERG "Error: Alternate function" |
| " signal multiplex control register not" |
| " mapped!\n"); |
| else |
| /* P1021 has pins muxed for QE and other functions. To |
| * enable QE UEC mode, we need to set bit QE0 for UCC1 |
| * in Eth mode, QE0 and QE3 for UCC5 in Eth mode, QE9 |
| * and QE12 for QE MII management signals in PMUXCR |
| * register. |
| */ |
| setbits32(pmuxcr, MPC85xx_PMUXCR_QE0 | |
| MPC85xx_PMUXCR_QE3 | |
| MPC85xx_PMUXCR_QE9 | |
| MPC85xx_PMUXCR_QE12); |
| |
| of_node_put(np); |
| } |
| |
| } |
| } |
| |
| static void __init mpc85xx_mds_qeic_init(void) |
| { |
| struct device_node *np; |
| |
| np = of_find_compatible_node(NULL, NULL, "fsl,qe"); |
| if (!of_device_is_available(np)) { |
| of_node_put(np); |
| return; |
| } |
| |
| np = of_find_compatible_node(NULL, NULL, "fsl,qe-ic"); |
| if (!np) { |
| np = of_find_node_by_type(NULL, "qeic"); |
| if (!np) |
| return; |
| } |
| |
| if (machine_is(p1021_mds)) |
| qe_ic_init(np, 0, qe_ic_cascade_low_mpic, |
| qe_ic_cascade_high_mpic); |
| else |
| qe_ic_init(np, 0, qe_ic_cascade_muxed_mpic, NULL); |
| of_node_put(np); |
| } |
| #else |
| static void __init mpc85xx_publish_qe_devices(void) { } |
| static void __init mpc85xx_mds_qe_init(void) { } |
| static void __init mpc85xx_mds_qeic_init(void) { } |
| #endif /* CONFIG_QUICC_ENGINE */ |
| |
| static void __init mpc85xx_mds_setup_arch(void) |
| { |
| #ifdef CONFIG_PCI |
| struct pci_controller *hose; |
| struct device_node *np; |
| #endif |
| dma_addr_t max = 0xffffffff; |
| |
| if (ppc_md.progress) |
| ppc_md.progress("mpc85xx_mds_setup_arch()", 0); |
| |
| #ifdef CONFIG_PCI |
| for_each_node_by_type(np, "pci") { |
| if (of_device_is_compatible(np, "fsl,mpc8540-pci") || |
| of_device_is_compatible(np, "fsl,mpc8548-pcie")) { |
| struct resource rsrc; |
| of_address_to_resource(np, 0, &rsrc); |
| if ((rsrc.start & 0xfffff) == 0x8000) |
| fsl_add_bridge(np, 1); |
| else |
| fsl_add_bridge(np, 0); |
| |
| hose = pci_find_hose_for_OF_device(np); |
| max = min(max, hose->dma_window_base_cur + |
| hose->dma_window_size); |
| } |
| } |
| #endif |
| |
| #ifdef CONFIG_SMP |
| mpc85xx_smp_init(); |
| #endif |
| |
| mpc85xx_mds_qe_init(); |
| |
| #ifdef CONFIG_SWIOTLB |
| if (memblock_end_of_DRAM() > max) { |
| ppc_swiotlb_enable = 1; |
| set_pci_dma_ops(&swiotlb_dma_ops); |
| ppc_md.pci_dma_dev_setup = pci_dma_dev_setup_swiotlb; |
| } |
| #endif |
| } |
| |
| |
| static int __init board_fixups(void) |
| { |
| char phy_id[20]; |
| char *compstrs[2] = {"fsl,gianfar-mdio", "fsl,ucc-mdio"}; |
| struct device_node *mdio; |
| struct resource res; |
| int i; |
| |
| for (i = 0; i < ARRAY_SIZE(compstrs); i++) { |
| mdio = of_find_compatible_node(NULL, NULL, compstrs[i]); |
| |
| of_address_to_resource(mdio, 0, &res); |
| snprintf(phy_id, sizeof(phy_id), "%llx:%02x", |
| (unsigned long long)res.start, 1); |
| |
| phy_register_fixup_for_id(phy_id, mpc8568_fixup_125_clock); |
| phy_register_fixup_for_id(phy_id, mpc8568_mds_phy_fixups); |
| |
| /* Register a workaround for errata */ |
| snprintf(phy_id, sizeof(phy_id), "%llx:%02x", |
| (unsigned long long)res.start, 7); |
| phy_register_fixup_for_id(phy_id, mpc8568_mds_phy_fixups); |
| |
| of_node_put(mdio); |
| } |
| |
| return 0; |
| } |
| machine_arch_initcall(mpc8568_mds, board_fixups); |
| machine_arch_initcall(mpc8569_mds, board_fixups); |
| |
| static struct of_device_id mpc85xx_ids[] = { |
| { .type = "soc", }, |
| { .compatible = "soc", }, |
| { .compatible = "simple-bus", }, |
| { .compatible = "gianfar", }, |
| { .compatible = "fsl,rapidio-delta", }, |
| { .compatible = "fsl,mpc8548-guts", }, |
| { .compatible = "gpio-leds", }, |
| {}, |
| }; |
| |
| static struct of_device_id p1021_ids[] = { |
| { .type = "soc", }, |
| { .compatible = "soc", }, |
| { .compatible = "simple-bus", }, |
| { .compatible = "gianfar", }, |
| {}, |
| }; |
| |
| static int __init mpc85xx_publish_devices(void) |
| { |
| if (machine_is(mpc8568_mds)) |
| simple_gpiochip_init("fsl,mpc8568mds-bcsr-gpio"); |
| if (machine_is(mpc8569_mds)) |
| simple_gpiochip_init("fsl,mpc8569mds-bcsr-gpio"); |
| |
| of_platform_bus_probe(NULL, mpc85xx_ids, NULL); |
| mpc85xx_publish_qe_devices(); |
| |
| return 0; |
| } |
| |
| static int __init p1021_publish_devices(void) |
| { |
| of_platform_bus_probe(NULL, p1021_ids, NULL); |
| mpc85xx_publish_qe_devices(); |
| |
| return 0; |
| } |
| |
| machine_device_initcall(mpc8568_mds, mpc85xx_publish_devices); |
| machine_device_initcall(mpc8569_mds, mpc85xx_publish_devices); |
| machine_device_initcall(p1021_mds, p1021_publish_devices); |
| |
| machine_arch_initcall(mpc8568_mds, swiotlb_setup_bus_notifier); |
| machine_arch_initcall(mpc8569_mds, swiotlb_setup_bus_notifier); |
| machine_arch_initcall(p1021_mds, swiotlb_setup_bus_notifier); |
| |
| static void __init mpc85xx_mds_pic_init(void) |
| { |
| struct mpic *mpic; |
| struct resource r; |
| struct device_node *np = NULL; |
| |
| np = of_find_node_by_type(NULL, "open-pic"); |
| if (!np) |
| return; |
| |
| if (of_address_to_resource(np, 0, &r)) { |
| printk(KERN_ERR "Failed to map mpic register space\n"); |
| of_node_put(np); |
| return; |
| } |
| |
| mpic = mpic_alloc(np, r.start, |
| MPIC_PRIMARY | MPIC_WANTS_RESET | MPIC_BIG_ENDIAN | |
| MPIC_BROKEN_FRR_NIRQS | MPIC_SINGLE_DEST_CPU, |
| 0, 256, " OpenPIC "); |
| BUG_ON(mpic == NULL); |
| of_node_put(np); |
| |
| mpic_init(mpic); |
| mpc85xx_mds_qeic_init(); |
| } |
| |
| static int __init mpc85xx_mds_probe(void) |
| { |
| unsigned long root = of_get_flat_dt_root(); |
| |
| return of_flat_dt_is_compatible(root, "MPC85xxMDS"); |
| } |
| |
| define_machine(mpc8568_mds) { |
| .name = "MPC8568 MDS", |
| .probe = mpc85xx_mds_probe, |
| .setup_arch = mpc85xx_mds_setup_arch, |
| .init_IRQ = mpc85xx_mds_pic_init, |
| .get_irq = mpic_get_irq, |
| .restart = fsl_rstcr_restart, |
| .calibrate_decr = generic_calibrate_decr, |
| .progress = udbg_progress, |
| #ifdef CONFIG_PCI |
| .pcibios_fixup_bus = fsl_pcibios_fixup_bus, |
| #endif |
| }; |
| |
| static int __init mpc8569_mds_probe(void) |
| { |
| unsigned long root = of_get_flat_dt_root(); |
| |
| return of_flat_dt_is_compatible(root, "fsl,MPC8569EMDS"); |
| } |
| |
| define_machine(mpc8569_mds) { |
| .name = "MPC8569 MDS", |
| .probe = mpc8569_mds_probe, |
| .setup_arch = mpc85xx_mds_setup_arch, |
| .init_IRQ = mpc85xx_mds_pic_init, |
| .get_irq = mpic_get_irq, |
| .restart = fsl_rstcr_restart, |
| .calibrate_decr = generic_calibrate_decr, |
| .progress = udbg_progress, |
| #ifdef CONFIG_PCI |
| .pcibios_fixup_bus = fsl_pcibios_fixup_bus, |
| #endif |
| }; |
| |
| static int __init p1021_mds_probe(void) |
| { |
| unsigned long root = of_get_flat_dt_root(); |
| |
| return of_flat_dt_is_compatible(root, "fsl,P1021MDS"); |
| |
| } |
| |
| define_machine(p1021_mds) { |
| .name = "P1021 MDS", |
| .probe = p1021_mds_probe, |
| .setup_arch = mpc85xx_mds_setup_arch, |
| .init_IRQ = mpc85xx_mds_pic_init, |
| .get_irq = mpic_get_irq, |
| .restart = fsl_rstcr_restart, |
| .calibrate_decr = generic_calibrate_decr, |
| .progress = udbg_progress, |
| #ifdef CONFIG_PCI |
| .pcibios_fixup_bus = fsl_pcibios_fixup_bus, |
| #endif |
| }; |
| |