| # Copyright 2008 Openmoko, Inc. |
| # Simtec Electronics, Ben Dooks <ben@simtec.co.uk> |
| # |
| # Licensed under GPLv2 |
| |
| # temporary until we can eliminate all drivers using it. |
| config PLAT_S3C64XX |
| bool |
| depends on ARCH_S3C64XX |
| select SAMSUNG_WAKEMASK |
| default y |
| help |
| Base platform code for any Samsung S3C64XX device |
| |
| |
| # Configuration options for the S3C6410 CPU |
| |
| config CPU_S3C6400 |
| bool |
| help |
| Enable S3C6400 CPU support |
| |
| config CPU_S3C6410 |
| bool |
| help |
| Enable S3C6410 CPU support |
| |
| config S3C64XX_DMA |
| bool "S3C64XX DMA" |
| select S3C_DMA |
| |
| config S3C64XX_SETUP_SDHCI |
| select S3C64XX_SETUP_SDHCI_GPIO |
| bool |
| help |
| Internal configuration for default SDHCI setup for S3C6400 and |
| S3C6410 SoCs. |
| |
| config S3C64XX_DEV_ONENAND1 |
| bool |
| help |
| Compile in platform device definition for OneNAND1 controller |
| |
| # platform specific device setup |
| |
| config S3C64XX_SETUP_I2C0 |
| bool |
| default y |
| help |
| Common setup code for i2c bus 0. |
| |
| Note, currently since i2c0 is always compiled, this setup helper |
| is always compiled with it. |
| |
| config S3C64XX_SETUP_I2C1 |
| bool |
| help |
| Common setup code for i2c bus 1. |
| |
| config S3C64XX_SETUP_IDE |
| bool |
| help |
| Common setup code for S3C64XX IDE. |
| |
| config S3C64XX_SETUP_FB_24BPP |
| bool |
| help |
| Common setup code for S3C64XX with an 24bpp RGB display helper. |
| |
| config S3C64XX_SETUP_KEYPAD |
| bool |
| help |
| Common setup code for S3C64XX KEYPAD GPIO configurations |
| |
| config S3C64XX_SETUP_SDHCI_GPIO |
| bool |
| help |
| Common setup code for S3C64XX SDHCI GPIO configurations |
| |
| # S36400 Macchine support |
| |
| config MACH_SMDK6400 |
| bool "SMDK6400" |
| select CPU_S3C6400 |
| select S3C_DEV_HSMMC |
| select S3C_DEV_NAND |
| select S3C64XX_SETUP_SDHCI |
| help |
| Machine support for the Samsung SMDK6400 |
| |
| # S3C6410 machine support |
| |
| config MACH_ANW6410 |
| bool "A&W6410" |
| select CPU_S3C6410 |
| select S3C_DEV_FB |
| select S3C64XX_SETUP_FB_24BPP |
| help |
| Machine support for the A&W6410 |
| |
| config MACH_REAL6410 |
| bool "REAL6410" |
| select CPU_S3C6410 |
| select S3C_DEV_HSMMC |
| select S3C_DEV_HSMMC1 |
| select S3C64XX_SETUP_SDHCI |
| help |
| Machine support for the CoreWind REAL6410 |
| |
| config MACH_SMDK6410 |
| bool "SMDK6410" |
| select CPU_S3C6410 |
| select SAMSUNG_DEV_ADC |
| select S3C_DEV_HSMMC |
| select S3C_DEV_HSMMC1 |
| select S3C_DEV_I2C1 |
| select SAMSUNG_DEV_IDE |
| select S3C_DEV_FB |
| select S3C_DEV_RTC |
| select SAMSUNG_DEV_TS |
| select S3C_DEV_USB_HOST |
| select S3C_DEV_USB_HSOTG |
| select S3C_DEV_WDT |
| select SAMSUNG_DEV_KEYPAD |
| select HAVE_S3C2410_WATCHDOG |
| select S3C64XX_SETUP_SDHCI |
| select S3C64XX_SETUP_I2C1 |
| select S3C64XX_SETUP_IDE |
| select S3C64XX_SETUP_FB_24BPP |
| select S3C64XX_SETUP_KEYPAD |
| help |
| Machine support for the Samsung SMDK6410 |
| |
| # At least some of the SMDK6410s were shipped with the card detect |
| # for the MMC/SD slots connected to the same input. This means that |
| # either the boards need to be altered to have channel0 to an alternate |
| # configuration or that only one slot can be used. |
| |
| choice |
| prompt "SMDK6410 MMC/SD slot setup" |
| depends on MACH_SMDK6410 |
| |
| config SMDK6410_SD_CH0 |
| bool "Use channel 0 only" |
| depends on MACH_SMDK6410 |
| help |
| Select CON7 (channel 0) as the MMC/SD slot, as |
| at least some SMDK6410 boards come with the |
| resistors fitted so that the card detects for |
| channels 0 and 1 are the same. |
| |
| config SMDK6410_SD_CH1 |
| bool "Use channel 1 only" |
| depends on MACH_SMDK6410 |
| help |
| Select CON6 (channel 1) as the MMC/SD slot, as |
| at least some SMDK6410 boards come with the |
| resistors fitted so that the card detects for |
| channels 0 and 1 are the same. |
| |
| endchoice |
| |
| config SMDK6410_WM1190_EV1 |
| bool "Support Wolfson Microelectronics 1190-EV1 PMIC card" |
| depends on MACH_SMDK6410 |
| select REGULATOR |
| select REGULATOR_WM8350 |
| select S3C24XX_GPIO_EXTRA64 |
| select MFD_WM8350_I2C |
| select MFD_WM8350_CONFIG_MODE_0 |
| select MFD_WM8350_CONFIG_MODE_3 |
| select MFD_WM8352_CONFIG_MODE_0 |
| help |
| The Wolfson Microelectronics 1190-EV1 is a WM835x based PMIC |
| and audio daughtercard for the Samsung SMDK6410 reference |
| platform. Enabling this option will build support for this |
| module into the kernel. The presence of the module will be |
| detected at runtime so the the resulting kernel can be used |
| with or without the 1190-EV1 fitted. |
| |
| config SMDK6410_WM1192_EV1 |
| bool "Support Wolfson Microelectronics 1192-EV1 PMIC card" |
| depends on MACH_SMDK6410 |
| select REGULATOR |
| select REGULATOR_WM831X |
| select S3C24XX_GPIO_EXTRA64 |
| select MFD_WM831X |
| select MFD_WM831X_I2C |
| help |
| The Wolfson Microelectronics 1192-EV1 is a WM831x based PMIC |
| daughtercard for the Samsung SMDK6410 reference platform. |
| Enabling this option will build support for this module into |
| the kernel. The presence of the daughtercard will be |
| detected at runtime so the the resulting kernel can be used |
| with or without the 1192-EV1 fitted. |
| |
| config MACH_NCP |
| bool "NCP" |
| select CPU_S3C6410 |
| select S3C_DEV_I2C1 |
| select S3C_DEV_HSMMC1 |
| select S3C64XX_SETUP_I2C1 |
| help |
| Machine support for the Samsung NCP |
| |
| config MACH_HMT |
| bool "Airgoo HMT" |
| select CPU_S3C6410 |
| select S3C_DEV_FB |
| select S3C_DEV_NAND |
| select S3C_DEV_USB_HOST |
| select S3C64XX_SETUP_FB_24BPP |
| select HAVE_PWM |
| help |
| Machine support for the Airgoo HMT |
| |
| config MACH_SMARTQ |
| bool |
| select CPU_S3C6410 |
| select S3C_DEV_HSMMC |
| select S3C_DEV_HSMMC1 |
| select S3C_DEV_HSMMC2 |
| select S3C_DEV_FB |
| select S3C_DEV_HWMON |
| select S3C_DEV_RTC |
| select S3C_DEV_USB_HSOTG |
| select S3C_DEV_USB_HOST |
| select S3C64XX_SETUP_SDHCI |
| select S3C64XX_SETUP_FB_24BPP |
| select SAMSUNG_DEV_ADC |
| select SAMSUNG_DEV_TS |
| select HAVE_PWM |
| help |
| Shared machine support for SmartQ 5/7 |
| |
| config MACH_SMARTQ5 |
| bool "SmartQ 5" |
| select MACH_SMARTQ |
| help |
| Machine support for the SmartQ 5 |
| |
| config MACH_SMARTQ7 |
| bool "SmartQ 7" |
| select MACH_SMARTQ |
| help |
| Machine support for the SmartQ 7 |