| /* |
| * Support for CompuLab CM-T3730 |
| */ |
| /dts-v1/; |
| |
| #include "omap36xx.dtsi" |
| #include "omap3-cm-t3x30.dtsi" |
| |
| / { |
| model = "CompuLab CM-T3730"; |
| compatible = "compulab,omap3-cm-t3730", "ti,omap36xx", "ti,omap3"; |
| |
| wl12xx_vmmc2: wl12xx_vmmc2 { |
| compatible = "regulator-fixed"; |
| regulator-name = "vw1271"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wl12xx_gpio>; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| gpio = <&gpio3 9 GPIO_ACTIVE_HIGH>; /* gpio73 */ |
| startup-delay-us = <20000>; |
| enable-active-high; |
| }; |
| |
| wl12xx_vaux2: wl12xx_vaux2 { |
| compatible = "regulator-fixed"; |
| regulator-name = "vwl1271_vaux2"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| vin-supply = <&vaux2>; |
| }; |
| }; |
| |
| &omap3_pmx_wkup { |
| dss_dpi_pins_cm_t3730: pinmux_dss_dpi_pins_cm_t3730 { |
| pinctrl-single,pins = < |
| OMAP3_WKUP_IOPAD(0x2a08, PIN_OUTPUT | MUX_MODE3) /* sys_boot0.dss_data18 */ |
| OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE3) /* sys_boot1.dss_data19 */ |
| OMAP3_WKUP_IOPAD(0x2a10, PIN_OUTPUT | MUX_MODE3) /* sys_boot3.dss_data20 */ |
| OMAP3_WKUP_IOPAD(0x2a12, PIN_OUTPUT | MUX_MODE3) /* sys_boot4.dss_data21 */ |
| OMAP3_WKUP_IOPAD(0x2a14, PIN_OUTPUT | MUX_MODE3) /* sys_boot5.dss_data22 */ |
| OMAP3_WKUP_IOPAD(0x2a16, PIN_OUTPUT | MUX_MODE3) /* sys_boot6.dss_data23 */ |
| >; |
| }; |
| }; |
| |
| &omap3_pmx_core { |
| |
| mmc2_pins: pinmux_mmc2_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ |
| OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ |
| OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ |
| OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ |
| OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ |
| OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ |
| >; |
| }; |
| |
| wl12xx_gpio: pinmux_wl12xx_gpio { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE4) /* dss_data3.gpio_73 */ |
| OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT | MUX_MODE4) /* sdmmc2_dat4.gpio_136 */ |
| >; |
| }; |
| }; |
| |
| &mmc2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mmc2_pins>; |
| vmmc-supply = <&wl12xx_vmmc2>; |
| vmmc_aux-supply = <&wl12xx_vaux2>; |
| non-removable; |
| bus-width = <4>; |
| cap-power-off-card; |
| }; |
| |
| &dss { |
| status = "ok"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = < |
| &dss_dpi_pins_common |
| &dss_dpi_pins_cm_t3730 |
| >; |
| }; |
| |