Merge branch 'pinmux-dt' of git://gitorious.org/sirfprima2-kernel/sirfprima2-kernel into next/dt
This branch enables device tree bindings for the CSR Prima pin control
subsystem. All patches acked by Linus W (pinctrl maintainer).
* 'pinmux-dt' of git://gitorious.org/sirfprima2-kernel/sirfprima2-kernel:
pinctrl: sirf: add DT-binding pinmux mapping support
ARM: PRIMA2: rename prima2-cb.dts to prima2.dtsi as it only has SoC features
ARM: PRIMA2: add missing interrupts property for pinctrl node
+ sync to Linux 3.6-rc4
diff --git a/Documentation/devicetree/bindings/arm/mrvl/tauros2.txt b/Documentation/devicetree/bindings/arm/mrvl/tauros2.txt
new file mode 100644
index 0000000..31af1cbb
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/mrvl/tauros2.txt
@@ -0,0 +1,17 @@
+* Marvell Tauros2 Cache
+
+Required properties:
+- compatible : Should be "marvell,tauros2-cache".
+- marvell,tauros2-cache-features : Specify the features supported for the
+ tauros2 cache.
+ The features including
+ CACHE_TAUROS2_PREFETCH_ON (1 << 0)
+ CACHE_TAUROS2_LINEFILL_BURST8 (1 << 1)
+ The definition can be found at
+ arch/arm/include/asm/hardware/cache-tauros2.h
+
+Example:
+ L2: l2-cache {
+ compatible = "marvell,tauros2-cache";
+ marvell,tauros2-cache-features = <0x3>;
+ };
diff --git a/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt b/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt
new file mode 100644
index 0000000..f1421e2
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt
@@ -0,0 +1,31 @@
+PXA3xx NAND DT bindings
+
+Required properties:
+
+ - compatible: Should be "marvell,pxa3xx-nand"
+ - reg: The register base for the controller
+ - interrupts: The interrupt to map
+ - #address-cells: Set to <1> if the node includes partitions
+
+Optional properties:
+
+ - marvell,nand-enable-arbiter: Set to enable the bus arbiter
+ - marvell,nand-keep-config: Set to keep the NAND controller config as set
+ by the bootloader
+ - num-cs: Number of chipselect lines to usw
+
+Example:
+
+ nand0: nand@43100000 {
+ compatible = "marvell,pxa3xx-nand";
+ reg = <0x43100000 90>;
+ interrupts = <45>;
+ #address-cells = <1>;
+
+ marvell,nand-enable-arbiter;
+ marvell,nand-keep-config;
+ num-cs = <1>;
+
+ /* partitions (optional) */
+ };
+
diff --git a/Documentation/devicetree/bindings/rtc/pxa-rtc.txt b/Documentation/devicetree/bindings/rtc/pxa-rtc.txt
new file mode 100644
index 0000000..8c6672a
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/pxa-rtc.txt
@@ -0,0 +1,14 @@
+* PXA RTC
+
+PXA specific RTC driver.
+
+Required properties:
+- compatible : Should be "marvell,pxa-rtc"
+
+Examples:
+
+rtc@40900000 {
+ compatible = "marvell,pxa-rtc";
+ reg = <0x40900000 0x3c>;
+ interrupts = <30 31>;
+};
diff --git a/arch/arm/boot/dts/mmp2.dtsi b/arch/arm/boot/dts/mmp2.dtsi
index 80f74e2..0514fb4 100644
--- a/arch/arm/boot/dts/mmp2.dtsi
+++ b/arch/arm/boot/dts/mmp2.dtsi
@@ -26,6 +26,11 @@
interrupt-parent = <&intc>;
ranges;
+ L2: l2-cache {
+ compatible = "marvell,tauros2-cache";
+ marvell,tauros2-cache-features = <0x3>;
+ };
+
axi@d4200000 { /* AXI */
compatible = "mrvl,axi-bus", "simple-bus";
#address-cells = <1>;
diff --git a/arch/arm/boot/dts/pxa27x.dtsi b/arch/arm/boot/dts/pxa27x.dtsi
new file mode 100644
index 0000000..d7c5d72
--- /dev/null
+++ b/arch/arm/boot/dts/pxa27x.dtsi
@@ -0,0 +1,14 @@
+/* The pxa3xx skeleton simply augments the 2xx version */
+/include/ "pxa2xx.dtsi"
+
+/ {
+ model = "Marvell PXA27x familiy SoC";
+ compatible = "marvell,pxa27x";
+
+ pxabus {
+ pxairq: interrupt-controller@40d00000 {
+ marvell,intc-priority;
+ marvell,intc-nr-irqs = <34>;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/pxa2xx.dtsi b/arch/arm/boot/dts/pxa2xx.dtsi
new file mode 100644
index 0000000..f18aad3
--- /dev/null
+++ b/arch/arm/boot/dts/pxa2xx.dtsi
@@ -0,0 +1,132 @@
+/*
+ * pxa2xx.dtsi - Device Tree Include file for Marvell PXA2xx family SoC
+ *
+ * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/include/ "skeleton.dtsi"
+
+/ {
+ model = "Marvell PXA2xx family SoC";
+ compatible = "marvell,pxa2xx";
+ interrupt-parent = <&pxairq>;
+
+ aliases {
+ serial0 = &ffuart;
+ serial1 = &btuart;
+ serial2 = &stuart;
+ serial3 = &hwuart;
+ i2c0 = &pwri2c;
+ i2c1 = &pxai2c1;
+ };
+
+ cpus {
+ cpu@0 {
+ compatible = "arm,xscale";
+ };
+ };
+
+ pxabus {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ pxairq: interrupt-controller@40d00000 {
+ #interrupt-cells = <1>;
+ compatible = "marvell,pxa-intc";
+ interrupt-controller;
+ interrupt-parent;
+ marvell,intc-nr-irqs = <32>;
+ reg = <0x40d00000 0xd0>;
+ };
+
+ gpio: gpio@40e00000 {
+ compatible = "mrvl,pxa-gpio";
+ #address-cells = <0x1>;
+ #size-cells = <0x1>;
+ reg = <0x40e00000 0x10000>;
+ gpio-controller;
+ #gpio-cells = <0x2>;
+ interrupts = <10>;
+ interrupt-names = "gpio_mux";
+ interrupt-controller;
+ #interrupt-cells = <0x2>;
+ ranges;
+
+ gcb0: gpio@40e00000 {
+ reg = <0x40e00000 0x4>;
+ };
+
+ gcb1: gpio@40e00004 {
+ reg = <0x40e00004 0x4>;
+ };
+
+ gcb2: gpio@40e00008 {
+ reg = <0x40e00008 0x4>;
+ };
+ gcb3: gpio@40e0000c {
+ reg = <0x40e0000c 0x4>;
+ };
+ };
+
+ ffuart: uart@40100000 {
+ compatible = "mrvl,pxa-uart";
+ reg = <0x40100000 0x30>;
+ interrupts = <22>;
+ status = "disabled";
+ };
+
+ btuart: uart@40200000 {
+ compatible = "mrvl,pxa-uart";
+ reg = <0x40200000 0x30>;
+ interrupts = <21>;
+ status = "disabled";
+ };
+
+ stuart: uart@40700000 {
+ compatible = "mrvl,pxa-uart";
+ reg = <0x40700000 0x30>;
+ interrupts = <20>;
+ status = "disabled";
+ };
+
+ hwuart: uart@41100000 {
+ compatible = "mrvl,pxa-uart";
+ reg = <0x41100000 0x30>;
+ interrupts = <7>;
+ status = "disabled";
+ };
+
+ pxai2c1: i2c@40301680 {
+ compatible = "mrvl,pxa-i2c";
+ reg = <0x40301680 0x30>;
+ interrupts = <18>;
+ #address-cells = <0x1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ usb0: ohci@4c000000 {
+ compatible = "mrvl,pxa-ohci";
+ reg = <0x4c000000 0x10000>;
+ interrupts = <3>;
+ status = "disabled";
+ };
+
+ mmc0: mmc@41100000 {
+ compatible = "mrvl,pxa-mmc";
+ reg = <0x41100000 0x1000>;
+ interrupts = <23>;
+ status = "disabled";
+ };
+
+ rtc@40900000 {
+ compatible = "marvell,pxa-rtc";
+ reg = <0x40900000 0x3c>;
+ interrupts = <30 31>;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/pxa3xx.dtsi b/arch/arm/boot/dts/pxa3xx.dtsi
new file mode 100644
index 0000000..f9d92da
--- /dev/null
+++ b/arch/arm/boot/dts/pxa3xx.dtsi
@@ -0,0 +1,32 @@
+/* The pxa3xx skeleton simply augments the 2xx version */
+/include/ "pxa2xx.dtsi"
+
+/ {
+ model = "Marvell PXA3xx familiy SoC";
+ compatible = "marvell,pxa3xx";
+
+ pxabus {
+ pwri2c: i2c@40f500c0 {
+ compatible = "mrvl,pwri2c";
+ reg = <0x40f500c0 0x30>;
+ interrupts = <6>;
+ #address-cells = <0x1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ nand0: nand@43100000 {
+ compatible = "marvell,pxa3xx-nand";
+ reg = <0x43100000 90>;
+ interrupts = <45>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ status = "disabled";
+ };
+
+ pxairq: interrupt-controller@40d00000 {
+ marvell,intc-priority;
+ marvell,intc-nr-irqs = <56>;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/pxa910.dtsi b/arch/arm/boot/dts/pxa910.dtsi
index aebf32d..a3be44d8 100644
--- a/arch/arm/boot/dts/pxa910.dtsi
+++ b/arch/arm/boot/dts/pxa910.dtsi
@@ -25,6 +25,11 @@
interrupt-parent = <&intc>;
ranges;
+ L2: l2-cache {
+ compatible = "marvell,tauros2-cache";
+ marvell,tauros2-cache-features = <0x3>;
+ };
+
axi@d4200000 { /* AXI */
compatible = "mrvl,axi-bus", "simple-bus";
#address-cells = <1>;
diff --git a/arch/arm/include/asm/hardware/cache-tauros2.h b/arch/arm/include/asm/hardware/cache-tauros2.h
index 538f17c..295e2e4 100644
--- a/arch/arm/include/asm/hardware/cache-tauros2.h
+++ b/arch/arm/include/asm/hardware/cache-tauros2.h
@@ -8,4 +8,7 @@
* warranty of any kind, whether express or implied.
*/
-extern void __init tauros2_init(void);
+#define CACHE_TAUROS2_PREFETCH_ON (1 << 0)
+#define CACHE_TAUROS2_LINEFILL_BURST8 (1 << 1)
+
+extern void __init tauros2_init(unsigned int features);
diff --git a/arch/arm/mach-dove/common.c b/arch/arm/mach-dove/common.c
index 6321567..e5a97d9 100644
--- a/arch/arm/mach-dove/common.c
+++ b/arch/arm/mach-dove/common.c
@@ -289,7 +289,7 @@
printk(KERN_INFO "TCLK = %dMHz\n", (get_tclk() + 499999) / 1000000);
#ifdef CONFIG_CACHE_TAUROS2
- tauros2_init();
+ tauros2_init(0);
#endif
dove_setup_cpu_mbus();
diff --git a/arch/arm/mach-mmp/mmp2.c b/arch/arm/mach-mmp/mmp2.c
index c709a24..c2bb95c 100644
--- a/arch/arm/mach-mmp/mmp2.c
+++ b/arch/arm/mach-mmp/mmp2.c
@@ -163,7 +163,7 @@
{
if (cpu_is_mmp2()) {
#ifdef CONFIG_CACHE_TAUROS2
- tauros2_init();
+ tauros2_init(0);
#endif
mfp_init_base(MFPR_VIRT_BASE);
mfp_init_addr(mmp2_addr_map);
diff --git a/arch/arm/mach-mmp/pxa910.c b/arch/arm/mach-mmp/pxa910.c
index 6da52e9..51ac8d1 100644
--- a/arch/arm/mach-mmp/pxa910.c
+++ b/arch/arm/mach-mmp/pxa910.c
@@ -14,6 +14,7 @@
#include <linux/io.h>
#include <linux/platform_device.h>
+#include <asm/hardware/cache-tauros2.h>
#include <asm/mach/time.h>
#include <mach/addr-map.h>
#include <mach/regs-apbc.h>
@@ -116,6 +117,9 @@
static int __init pxa910_init(void)
{
if (cpu_is_pxa910()) {
+#ifdef CONFIG_CACHE_TAUROS2
+ tauros2_init(0);
+#endif
mfp_init_base(MFPR_VIRT_BASE);
mfp_init_addr(pxa910_mfp_addr_map);
pxa_init_dma(IRQ_PXA910_DMA_INT0, 32);
diff --git a/arch/arm/mach-pxa/Kconfig b/arch/arm/mach-pxa/Kconfig
index fe2d1f8..8e6288d 100644
--- a/arch/arm/mach-pxa/Kconfig
+++ b/arch/arm/mach-pxa/Kconfig
@@ -25,6 +25,18 @@
if !ARCH_PXA_V7
comment "Intel/Marvell Dev Platforms (sorted by hardware release time)"
+config MACH_PXA3XX_DT
+ bool "Support PXA3xx platforms from device tree"
+ select PXA3xx
+ select CPU_PXA300
+ select POWER_SUPPLY
+ select HAVE_PWM
+ select USE_OF
+ help
+ Include support for Marvell PXA3xx based platforms using
+ the device tree. Needn't select any other machine while
+ MACH_PXA3XX_DT is enabled.
+
config ARCH_LUBBOCK
bool "Intel DBPXA250 Development Platform (aka Lubbock)"
select PXA25x
diff --git a/arch/arm/mach-pxa/Makefile b/arch/arm/mach-pxa/Makefile
index be0f7df..2bedc9e 100644
--- a/arch/arm/mach-pxa/Makefile
+++ b/arch/arm/mach-pxa/Makefile
@@ -26,6 +26,9 @@
# NOTE: keep the order of boards in accordance to their order in Kconfig
+# Device Tree support
+obj-$(CONFIG_MACH_PXA3XX_DT) += pxa-dt.o
+
# Intel/Marvell Dev Platforms
obj-$(CONFIG_ARCH_LUBBOCK) += lubbock.o
obj-$(CONFIG_MACH_MAINSTONE) += mainstone.o
diff --git a/arch/arm/mach-pxa/clock-pxa3xx.c b/arch/arm/mach-pxa/clock-pxa3xx.c
index 2a37a9a..d4e9499 100644
--- a/arch/arm/mach-pxa/clock-pxa3xx.c
+++ b/arch/arm/mach-pxa/clock-pxa3xx.c
@@ -127,8 +127,10 @@
if (clk->cken < 32)
CKENA |= mask;
- else
+ else if (clk->cken < 64)
CKENB |= mask;
+ else
+ CKENC |= mask;
}
void clk_pxa3xx_cken_disable(struct clk *clk)
@@ -137,8 +139,10 @@
if (clk->cken < 32)
CKENA &= ~mask;
- else
+ else if (clk->cken < 64)
CKENB &= ~mask;
+ else
+ CKENC &= ~mask;
}
const struct clkops clk_pxa3xx_cken_ops = {
diff --git a/arch/arm/mach-pxa/include/mach/pxa3xx-regs.h b/arch/arm/mach-pxa/include/mach/pxa3xx-regs.h
index 207ecb4..f4d48d2 100644
--- a/arch/arm/mach-pxa/include/mach/pxa3xx-regs.h
+++ b/arch/arm/mach-pxa/include/mach/pxa3xx-regs.h
@@ -131,6 +131,7 @@
#define AICSR __REG(0x41340008) /* Application Subsystem Interrupt Control/Status Register */
#define CKENA __REG(0x4134000C) /* A Clock Enable Register */
#define CKENB __REG(0x41340010) /* B Clock Enable Register */
+#define CKENC __REG(0x41340024) /* C Clock Enable Register */
#define AC97_DIV __REG(0x41340014) /* AC97 clock divisor value register */
#define ACCR_XPDIS (1 << 31) /* Core PLL Output Disable */
diff --git a/arch/arm/mach-pxa/irq.c b/arch/arm/mach-pxa/irq.c
index 5dae15e..b6cc181 100644
--- a/arch/arm/mach-pxa/irq.c
+++ b/arch/arm/mach-pxa/irq.c
@@ -17,6 +17,8 @@
#include <linux/syscore_ops.h>
#include <linux/io.h>
#include <linux/irq.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
#include <asm/exception.h>
@@ -25,8 +27,6 @@
#include "generic.h"
-#define IRQ_BASE io_p2v(0x40d00000)
-
#define ICIP (0x000)
#define ICMR (0x004)
#define ICLR (0x008)
@@ -48,22 +48,19 @@
* This is for peripheral IRQs internal to the PXA chip.
*/
+static void __iomem *pxa_irq_base;
static int pxa_internal_irq_nr;
-
-static inline int cpu_has_ipr(void)
-{
- return !cpu_is_pxa25x();
-}
+static bool cpu_has_ipr;
static inline void __iomem *irq_base(int i)
{
- static unsigned long phys_base[] = {
- 0x40d00000,
- 0x40d0009c,
- 0x40d00130,
+ static unsigned long phys_base_offset[] = {
+ 0x0,
+ 0x9c,
+ 0x130,
};
- return io_p2v(phys_base[i]);
+ return pxa_irq_base + phys_base_offset[i];
}
void pxa_mask_irq(struct irq_data *d)
@@ -96,8 +93,8 @@
uint32_t icip, icmr, mask;
do {
- icip = __raw_readl(IRQ_BASE + ICIP);
- icmr = __raw_readl(IRQ_BASE + ICMR);
+ icip = __raw_readl(pxa_irq_base + ICIP);
+ icmr = __raw_readl(pxa_irq_base + ICMR);
mask = icip & icmr;
if (mask == 0)
@@ -128,6 +125,8 @@
BUG_ON(irq_nr > MAX_INTERNAL_IRQS);
pxa_internal_irq_nr = irq_nr;
+ cpu_has_ipr = !cpu_is_pxa25x();
+ pxa_irq_base = io_p2v(0x40d00000);
for (n = 0; n < irq_nr; n += 32) {
void __iomem *base = irq_base(n >> 5);
@@ -136,8 +135,8 @@
__raw_writel(0, base + ICLR); /* all IRQs are IRQ, not FIQ */
for (i = n; (i < (n + 32)) && (i < irq_nr); i++) {
/* initialize interrupt priority */
- if (cpu_has_ipr())
- __raw_writel(i | IPR_VALID, IRQ_BASE + IPR(i));
+ if (cpu_has_ipr)
+ __raw_writel(i | IPR_VALID, pxa_irq_base + IPR(i));
irq = PXA_IRQ(i);
irq_set_chip_and_handler(irq, &pxa_internal_irq_chip,
@@ -168,9 +167,9 @@
__raw_writel(0, base + ICMR);
}
- if (cpu_has_ipr()) {
+ if (cpu_has_ipr) {
for (i = 0; i < pxa_internal_irq_nr; i++)
- saved_ipr[i] = __raw_readl(IRQ_BASE + IPR(i));
+ saved_ipr[i] = __raw_readl(pxa_irq_base + IPR(i));
}
return 0;
@@ -187,11 +186,11 @@
__raw_writel(0, base + ICLR);
}
- if (cpu_has_ipr())
+ if (cpu_has_ipr)
for (i = 0; i < pxa_internal_irq_nr; i++)
- __raw_writel(saved_ipr[i], IRQ_BASE + IPR(i));
+ __raw_writel(saved_ipr[i], pxa_irq_base + IPR(i));
- __raw_writel(1, IRQ_BASE + ICCR);
+ __raw_writel(1, pxa_irq_base + ICCR);
}
#else
#define pxa_irq_suspend NULL
@@ -202,3 +201,93 @@
.suspend = pxa_irq_suspend,
.resume = pxa_irq_resume,
};
+
+#ifdef CONFIG_OF
+static struct irq_domain *pxa_irq_domain;
+
+static int pxa_irq_map(struct irq_domain *h, unsigned int virq,
+ irq_hw_number_t hw)
+{
+ void __iomem *base = irq_base(hw / 32);
+
+ /* initialize interrupt priority */
+ if (cpu_has_ipr)
+ __raw_writel(hw | IPR_VALID, pxa_irq_base + IPR(hw));
+
+ irq_set_chip_and_handler(hw, &pxa_internal_irq_chip,
+ handle_level_irq);
+ irq_set_chip_data(hw, base);
+ set_irq_flags(hw, IRQF_VALID);
+
+ return 0;
+}
+
+static struct irq_domain_ops pxa_irq_ops = {
+ .map = pxa_irq_map,
+ .xlate = irq_domain_xlate_onecell,
+};
+
+static const struct of_device_id intc_ids[] __initconst = {
+ { .compatible = "marvell,pxa-intc", },
+ {}
+};
+
+void __init pxa_dt_irq_init(int (*fn)(struct irq_data *, unsigned int))
+{
+ struct device_node *node;
+ const struct of_device_id *of_id;
+ struct pxa_intc_conf *conf;
+ struct resource res;
+ int n, ret;
+
+ node = of_find_matching_node(NULL, intc_ids);
+ if (!node) {
+ pr_err("Failed to find interrupt controller in arch-pxa\n");
+ return;
+ }
+ of_id = of_match_node(intc_ids, node);
+ conf = of_id->data;
+
+ ret = of_property_read_u32(node, "marvell,intc-nr-irqs",
+ &pxa_internal_irq_nr);
+ if (ret) {
+ pr_err("Not found marvell,intc-nr-irqs property\n");
+ return;
+ }
+
+ ret = of_address_to_resource(node, 0, &res);
+ if (ret < 0) {
+ pr_err("No registers defined for node\n");
+ return;
+ }
+ pxa_irq_base = io_p2v(res.start);
+
+ if (of_find_property(node, "marvell,intc-priority", NULL))
+ cpu_has_ipr = 1;
+
+ ret = irq_alloc_descs(-1, 0, pxa_internal_irq_nr, 0);
+ if (ret < 0) {
+ pr_err("Failed to allocate IRQ numbers\n");
+ return;
+ }
+
+ pxa_irq_domain = irq_domain_add_legacy(node, pxa_internal_irq_nr, 0, 0,
+ &pxa_irq_ops, NULL);
+ if (!pxa_irq_domain)
+ panic("Unable to add PXA IRQ domain\n");
+
+ irq_set_default_host(pxa_irq_domain);
+
+ for (n = 0; n < pxa_internal_irq_nr; n += 32) {
+ void __iomem *base = irq_base(n >> 5);
+
+ __raw_writel(0, base + ICMR); /* disable all IRQs */
+ __raw_writel(0, base + ICLR); /* all IRQs are IRQ, not FIQ */
+ }
+
+ /* only unmasked interrupts kick us out of idle */
+ __raw_writel(1, irq_base(0) + ICCR);
+
+ pxa_internal_irq_chip.irq_set_wake = fn;
+}
+#endif /* CONFIG_OF */
diff --git a/arch/arm/mach-pxa/pxa-dt.c b/arch/arm/mach-pxa/pxa-dt.c
new file mode 100644
index 0000000..c9192ce
--- /dev/null
+++ b/arch/arm/mach-pxa/pxa-dt.c
@@ -0,0 +1,63 @@
+/*
+ * linux/arch/arm/mach-pxa/pxa-dt.c
+ *
+ * Copyright (C) 2012 Daniel Mack
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * publishhed by the Free Software Foundation.
+ */
+
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/time.h>
+#include <mach/irqs.h>
+#include <mach/pxa3xx.h>
+
+#include "generic.h"
+
+#ifdef CONFIG_PXA3xx
+extern void __init pxa3xx_dt_init_irq(void);
+
+static const struct of_dev_auxdata pxa3xx_auxdata_lookup[] __initconst = {
+ OF_DEV_AUXDATA("mrvl,pxa-uart", 0x40100000, "pxa2xx-uart.0", NULL),
+ OF_DEV_AUXDATA("mrvl,pxa-uart", 0x40200000, "pxa2xx-uart.1", NULL),
+ OF_DEV_AUXDATA("mrvl,pxa-uart", 0x40700000, "pxa2xx-uart.2", NULL),
+ OF_DEV_AUXDATA("mrvl,pxa-uart", 0x41600000, "pxa2xx-uart.3", NULL),
+ OF_DEV_AUXDATA("marvell,pxa-mmc", 0x41100000, "pxa2xx-mci.0", NULL),
+ OF_DEV_AUXDATA("mrvl,pxa-gpio", 0x40e00000, "pxa-gpio", NULL),
+ OF_DEV_AUXDATA("marvell,pxa-ohci", 0x4c000000, "pxa27x-ohci", NULL),
+ OF_DEV_AUXDATA("mrvl,pxa-i2c", 0x40301680, "pxa2xx-i2c.0", NULL),
+ OF_DEV_AUXDATA("mrvl,pwri2c", 0x40f500c0, "pxa3xx-i2c.1", NULL),
+ OF_DEV_AUXDATA("marvell,pxa3xx-nand", 0x43100000, "pxa3xx-nand", NULL),
+ {}
+};
+
+static void __init pxa3xx_dt_init(void)
+{
+ of_platform_populate(NULL, of_default_bus_match_table,
+ pxa3xx_auxdata_lookup, NULL);
+}
+
+static const char *pxa3xx_dt_board_compat[] __initdata = {
+ "marvell,pxa300",
+ "marvell,pxa310",
+ "marvell,pxa320",
+ NULL,
+};
+#endif
+
+#ifdef CONFIG_PXA3xx
+DT_MACHINE_START(PXA_DT, "Marvell PXA3xx (Device Tree Support)")
+ .map_io = pxa3xx_map_io,
+ .init_irq = pxa3xx_dt_init_irq,
+ .handle_irq = pxa3xx_handle_irq,
+ .timer = &pxa_timer,
+ .restart = pxa_restart,
+ .init_machine = pxa3xx_dt_init,
+ .dt_compat = pxa3xx_dt_board_compat,
+MACHINE_END
+#endif
diff --git a/arch/arm/mach-pxa/pxa3xx.c b/arch/arm/mach-pxa/pxa3xx.c
index dffb7e8..ff9c957 100644
--- a/arch/arm/mach-pxa/pxa3xx.c
+++ b/arch/arm/mach-pxa/pxa3xx.c
@@ -19,6 +19,7 @@
#include <linux/platform_device.h>
#include <linux/irq.h>
#include <linux/io.h>
+#include <linux/of.h>
#include <linux/syscore_ops.h>
#include <linux/i2c/pxa-i2c.h>
@@ -40,6 +41,8 @@
#define PECR_IE(n) ((1 << ((n) * 2)) << 28)
#define PECR_IS(n) ((1 << ((n) * 2)) << 29)
+extern void __init pxa_dt_irq_init(int (*fn)(struct irq_data *, unsigned int));
+
static DEFINE_PXA3_CKEN(pxa3xx_ffuart, FFUART, 14857000, 1);
static DEFINE_PXA3_CKEN(pxa3xx_btuart, BTUART, 14857000, 1);
static DEFINE_PXA3_CKEN(pxa3xx_stuart, STUART, 14857000, 1);
@@ -382,7 +385,7 @@
pxa_ext_wakeup_chip.irq_set_wake = fn;
}
-void __init pxa3xx_init_irq(void)
+static void __init __pxa3xx_init_irq(void)
{
/* enable CP6 access */
u32 value;
@@ -390,10 +393,23 @@
value |= (1 << 6);
__asm__ __volatile__("mcr p15, 0, %0, c15, c1, 0\n": :"r"(value));
- pxa_init_irq(56, pxa3xx_set_wake);
pxa_init_ext_wakeup_irq(pxa3xx_set_wake);
}
+void __init pxa3xx_init_irq(void)
+{
+ __pxa3xx_init_irq();
+ pxa_init_irq(56, pxa3xx_set_wake);
+}
+
+#ifdef CONFIG_OF
+void __init pxa3xx_dt_init_irq(void)
+{
+ __pxa3xx_init_irq();
+ pxa_dt_irq_init(pxa3xx_set_wake);
+}
+#endif /* CONFIG_OF */
+
static struct map_desc pxa3xx_io_desc[] __initdata = {
{ /* Mem Ctl */
.virtual = (unsigned long)SMEMC_VIRT,
@@ -466,7 +482,8 @@
register_syscore_ops(&pxa3xx_mfp_syscore_ops);
register_syscore_ops(&pxa3xx_clock_syscore_ops);
- ret = platform_add_devices(devices, ARRAY_SIZE(devices));
+ if (!of_have_populated_dt())
+ ret = platform_add_devices(devices, ARRAY_SIZE(devices));
}
return ret;
diff --git a/arch/arm/mach-shmobile/Makefile.boot b/arch/arm/mach-shmobile/Makefile.boot
index 498efd9..5e41019 100644
--- a/arch/arm/mach-shmobile/Makefile.boot
+++ b/arch/arm/mach-shmobile/Makefile.boot
@@ -7,3 +7,7 @@
#
#params_phys-y (Instead: Pass atags pointer in r2)
#initrd_phys-y (Instead: Use compiled-in initramfs)
+
+dtb-$(CONFIG_MACH_KZM9G) += sh73a0-kzm9g.dtb
+dtb-$(CONFIG_MACH_KZM9D) += emev2-kzm9d.dtb
+dtb-$(CONFIG_MACH_ARMADILLO800EVA) += r8a7740-armadillo800eva.dtb
diff --git a/arch/arm/mm/cache-tauros2.c b/arch/arm/mm/cache-tauros2.c
index 23a7643..1be0f4e 100644
--- a/arch/arm/mm/cache-tauros2.c
+++ b/arch/arm/mm/cache-tauros2.c
@@ -15,8 +15,11 @@
*/
#include <linux/init.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
#include <asm/cacheflush.h>
#include <asm/cp15.h>
+#include <asm/cputype.h>
#include <asm/hardware/cache-tauros2.h>
@@ -144,25 +147,8 @@
__asm__("mcr p15, 1, %0, c15, c1, 0" : : "r" (u));
}
-static void __init disable_l2_prefetch(void)
-{
- u32 u;
-
- /*
- * Read the CPU Extra Features register and verify that the
- * Disable L2 Prefetch bit is set.
- */
- u = read_extra_features();
- if (!(u & 0x01000000)) {
- printk(KERN_INFO "Tauros2: Disabling L2 prefetch.\n");
- write_extra_features(u | 0x01000000);
- }
-}
-
static inline int __init cpuid_scheme(void)
{
- extern int processor_id;
-
return !!((processor_id & 0x000f0000) == 0x000f0000);
}
@@ -189,12 +175,36 @@
__asm__("mcr p15, 0, %0, c1, c0, 1\n" : : "r" (actlr));
}
-void __init tauros2_init(void)
+static void enable_extra_feature(unsigned int features)
{
- extern int processor_id;
- char *mode;
+ u32 u;
- disable_l2_prefetch();
+ u = read_extra_features();
+
+ if (features & CACHE_TAUROS2_PREFETCH_ON)
+ u &= ~0x01000000;
+ else
+ u |= 0x01000000;
+ printk(KERN_INFO "Tauros2: %s L2 prefetch.\n",
+ (features & CACHE_TAUROS2_PREFETCH_ON)
+ ? "Enabling" : "Disabling");
+
+ if (features & CACHE_TAUROS2_LINEFILL_BURST8)
+ u |= 0x00100000;
+ else
+ u &= ~0x00100000;
+ printk(KERN_INFO "Tauros2: %s line fill burt8.\n",
+ (features & CACHE_TAUROS2_LINEFILL_BURST8)
+ ? "Enabling" : "Disabling");
+
+ write_extra_features(u);
+}
+
+static void __init tauros2_internal_init(unsigned int features)
+{
+ char *mode = NULL;
+
+ enable_extra_feature(features);
#ifdef CONFIG_CPU_32v5
if ((processor_id & 0xff0f0000) == 0x56050000) {
@@ -286,3 +296,34 @@
printk(KERN_INFO "Tauros2: L2 cache support initialised "
"in %s mode.\n", mode);
}
+
+#ifdef CONFIG_OF
+static const struct of_device_id tauros2_ids[] __initconst = {
+ { .compatible = "marvell,tauros2-cache"},
+ {}
+};
+#endif
+
+void __init tauros2_init(unsigned int features)
+{
+#ifdef CONFIG_OF
+ struct device_node *node;
+ int ret;
+ unsigned int f;
+
+ node = of_find_matching_node(NULL, tauros2_ids);
+ if (!node) {
+ pr_info("Not found marvell,tauros2-cache, disable it\n");
+ return;
+ }
+
+ ret = of_property_read_u32(node, "marvell,tauros2-cache-features", &f);
+ if (ret) {
+ pr_info("Not found marvell,tauros-cache-features property, "
+ "disable extra features\n");
+ features = 0;
+ } else
+ features = f;
+#endif
+ tauros2_internal_init(features);
+}
diff --git a/drivers/gpio/gpio-pxa.c b/drivers/gpio/gpio-pxa.c
index 9cac88a..9528779 100644
--- a/drivers/gpio/gpio-pxa.c
+++ b/drivers/gpio/gpio-pxa.c
@@ -26,6 +26,8 @@
#include <linux/syscore_ops.h>
#include <linux/slab.h>
+#include <asm/mach/irq.h>
+
#include <mach/irqs.h>
/*
@@ -59,6 +61,7 @@
#define BANK_OFF(n) (((n) < 3) ? (n) << 2 : 0x100 + (((n) - 3) << 2))
int pxa_last_gpio;
+static int irq_base;
#ifdef CONFIG_OF
static struct irq_domain *domain;
@@ -167,63 +170,14 @@
return ret;
}
-#ifdef CONFIG_ARCH_PXA
-static inline int __pxa_gpio_to_irq(int gpio)
-{
- if (gpio_is_pxa_type(gpio_type))
- return PXA_GPIO_TO_IRQ(gpio);
- return -1;
-}
-
-static inline int __pxa_irq_to_gpio(int irq)
-{
- if (gpio_is_pxa_type(gpio_type))
- return irq - PXA_GPIO_TO_IRQ(0);
- return -1;
-}
-#else
-static inline int __pxa_gpio_to_irq(int gpio) { return -1; }
-static inline int __pxa_irq_to_gpio(int irq) { return -1; }
-#endif
-
-#ifdef CONFIG_ARCH_MMP
-static inline int __mmp_gpio_to_irq(int gpio)
-{
- if (gpio_is_mmp_type(gpio_type))
- return MMP_GPIO_TO_IRQ(gpio);
- return -1;
-}
-
-static inline int __mmp_irq_to_gpio(int irq)
-{
- if (gpio_is_mmp_type(gpio_type))
- return irq - MMP_GPIO_TO_IRQ(0);
- return -1;
-}
-#else
-static inline int __mmp_gpio_to_irq(int gpio) { return -1; }
-static inline int __mmp_irq_to_gpio(int irq) { return -1; }
-#endif
-
static int pxa_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
{
- int gpio, ret;
-
- gpio = chip->base + offset;
- ret = __pxa_gpio_to_irq(gpio);
- if (ret >= 0)
- return ret;
- return __mmp_gpio_to_irq(gpio);
+ return chip->base + offset + irq_base;
}
int pxa_irq_to_gpio(int irq)
{
- int ret;
-
- ret = __pxa_irq_to_gpio(irq);
- if (ret >= 0)
- return ret;
- return __mmp_irq_to_gpio(irq);
+ return irq - irq_base;
}
static int pxa_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
@@ -403,6 +357,9 @@
struct pxa_gpio_chip *c;
int loop, gpio, gpio_base, n;
unsigned long gedr;
+ struct irq_chip *chip = irq_desc_get_chip(desc);
+
+ chained_irq_enter(chip, desc);
do {
loop = 0;
@@ -422,6 +379,8 @@
}
}
} while (loop);
+
+ chained_irq_exit(chip, desc);
}
static void pxa_ack_muxed_gpio(struct irq_data *d)
@@ -535,7 +494,7 @@
static int __devinit pxa_gpio_probe_dt(struct platform_device *pdev)
{
- int ret, nr_banks, nr_gpios, irq_base;
+ int ret, nr_banks, nr_gpios;
struct device_node *prev, *next, *np = pdev->dev.of_node;
const struct of_device_id *of_id =
of_match_device(pxa_gpio_dt_ids, &pdev->dev);
@@ -590,10 +549,20 @@
int irq0 = 0, irq1 = 0, irq_mux, gpio_offset = 0;
ret = pxa_gpio_probe_dt(pdev);
- if (ret < 0)
+ if (ret < 0) {
pxa_last_gpio = pxa_gpio_nums();
- else
+#ifdef CONFIG_ARCH_PXA
+ if (gpio_is_pxa_type(gpio_type))
+ irq_base = PXA_GPIO_TO_IRQ(0);
+#endif
+#ifdef CONFIG_ARCH_MMP
+ if (gpio_is_mmp_type(gpio_type))
+ irq_base = MMP_GPIO_TO_IRQ(0);
+#endif
+ } else {
use_of = 1;
+ }
+
if (!pxa_last_gpio)
return -EINVAL;
diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index 252aaef..d944d6e 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -22,6 +22,8 @@
#include <linux/io.h>
#include <linux/irq.h>
#include <linux/slab.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
#include <mach/dma.h>
#include <plat/pxa3xx_nand.h>
@@ -1032,7 +1034,7 @@
struct pxa3xx_nand_platform_data *pdata;
struct pxa3xx_nand_info *info;
struct pxa3xx_nand_host *host;
- struct nand_chip *chip;
+ struct nand_chip *chip = NULL;
struct mtd_info *mtd;
struct resource *r;
int ret, irq, cs;
@@ -1081,21 +1083,31 @@
}
clk_enable(info->clk);
- r = platform_get_resource(pdev, IORESOURCE_DMA, 0);
- if (r == NULL) {
- dev_err(&pdev->dev, "no resource defined for data DMA\n");
- ret = -ENXIO;
- goto fail_put_clk;
- }
- info->drcmr_dat = r->start;
+ /*
+ * This is a dirty hack to make this driver work from devicetree
+ * bindings. It can be removed once we have a prober DMA controller
+ * framework for DT.
+ */
+ if (pdev->dev.of_node && cpu_is_pxa3xx()) {
+ info->drcmr_dat = 97;
+ info->drcmr_cmd = 99;
+ } else {
+ r = platform_get_resource(pdev, IORESOURCE_DMA, 0);
+ if (r == NULL) {
+ dev_err(&pdev->dev, "no resource defined for data DMA\n");
+ ret = -ENXIO;
+ goto fail_put_clk;
+ }
+ info->drcmr_dat = r->start;
- r = platform_get_resource(pdev, IORESOURCE_DMA, 1);
- if (r == NULL) {
- dev_err(&pdev->dev, "no resource defined for command DMA\n");
- ret = -ENXIO;
- goto fail_put_clk;
+ r = platform_get_resource(pdev, IORESOURCE_DMA, 1);
+ if (r == NULL) {
+ dev_err(&pdev->dev, "no resource defined for command DMA\n");
+ ret = -ENXIO;
+ goto fail_put_clk;
+ }
+ info->drcmr_cmd = r->start;
}
- info->drcmr_cmd = r->start;
irq = platform_get_irq(pdev, 0);
if (irq < 0) {
@@ -1200,12 +1212,55 @@
return 0;
}
+#ifdef CONFIG_OF
+static struct of_device_id pxa3xx_nand_dt_ids[] = {
+ { .compatible = "marvell,pxa3xx-nand" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, i2c_pxa_dt_ids);
+
+static int pxa3xx_nand_probe_dt(struct platform_device *pdev)
+{
+ struct pxa3xx_nand_platform_data *pdata;
+ struct device_node *np = pdev->dev.of_node;
+ const struct of_device_id *of_id =
+ of_match_device(pxa3xx_nand_dt_ids, &pdev->dev);
+
+ if (!of_id)
+ return 0;
+
+ pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
+ if (!pdata)
+ return -ENOMEM;
+
+ if (of_get_property(np, "marvell,nand-enable-arbiter", NULL))
+ pdata->enable_arbiter = 1;
+ if (of_get_property(np, "marvell,nand-keep-config", NULL))
+ pdata->keep_config = 1;
+ of_property_read_u32(np, "num-cs", &pdata->num_cs);
+
+ pdev->dev.platform_data = pdata;
+
+ return 0;
+}
+#else
+static inline int pxa3xx_nand_probe_dt(struct platform_device *pdev)
+{
+ return 0;
+}
+#endif
+
static int pxa3xx_nand_probe(struct platform_device *pdev)
{
struct pxa3xx_nand_platform_data *pdata;
+ struct mtd_part_parser_data ppdata = {};
struct pxa3xx_nand_info *info;
int ret, cs, probe_success;
+ ret = pxa3xx_nand_probe_dt(pdev);
+ if (ret)
+ return ret;
+
pdata = pdev->dev.platform_data;
if (!pdata) {
dev_err(&pdev->dev, "no platform data defined\n");
@@ -1229,8 +1284,9 @@
continue;
}
+ ppdata.of_node = pdev->dev.of_node;
ret = mtd_device_parse_register(info->host[cs]->mtd, NULL,
- NULL, pdata->parts[cs],
+ &ppdata, pdata->parts[cs],
pdata->nr_parts[cs]);
if (!ret)
probe_success = 1;
@@ -1306,6 +1362,7 @@
static struct platform_driver pxa3xx_nand_driver = {
.driver = {
.name = "pxa3xx-nand",
+ .of_match_table = of_match_ptr(pxa3xx_nand_dt_ids),
},
.probe = pxa3xx_nand_probe,
.remove = pxa3xx_nand_remove,
diff --git a/drivers/rtc/rtc-pxa.c b/drivers/rtc/rtc-pxa.c
index 0075c8f..f771b2e 100644
--- a/drivers/rtc/rtc-pxa.c
+++ b/drivers/rtc/rtc-pxa.c
@@ -27,6 +27,8 @@
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/slab.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
#include <mach/hardware.h>
@@ -396,6 +398,14 @@
return 0;
}
+#ifdef CONFIG_OF
+static struct of_device_id pxa_rtc_dt_ids[] = {
+ { .compatible = "marvell,pxa-rtc" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, pxa_rtc_dt_ids);
+#endif
+
#ifdef CONFIG_PM
static int pxa_rtc_suspend(struct device *dev)
{
@@ -425,6 +435,7 @@
.remove = __exit_p(pxa_rtc_remove),
.driver = {
.name = "pxa-rtc",
+ .of_match_table = of_match_ptr(pxa_rtc_dt_ids),
#ifdef CONFIG_PM
.pm = &pxa_rtc_pm_ops,
#endif