| /* |
| * linux/arch/arm/plat-omap/gpio.c |
| * |
| * Support functions for OMAP GPIO |
| * |
| * Copyright (C) 2003-2005 Nokia Corporation |
| * Written by Juha Yrjölä <juha.yrjola@nokia.com> |
| * |
| * Copyright (C) 2009 Texas Instruments |
| * Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar@ti.com> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| |
| #include <linux/init.h> |
| #include <linux/module.h> |
| #include <linux/interrupt.h> |
| #include <linux/sysdev.h> |
| #include <linux/err.h> |
| #include <linux/clk.h> |
| #include <linux/io.h> |
| |
| #include <mach/hardware.h> |
| #include <asm/irq.h> |
| #include <mach/irqs.h> |
| #include <mach/gpio.h> |
| #include <asm/mach/irq.h> |
| #include <plat/powerdomain.h> |
| |
| /* |
| * OMAP1510 GPIO registers |
| */ |
| #define OMAP1510_GPIO_BASE 0xfffce000 |
| #define OMAP1510_GPIO_DATA_INPUT 0x00 |
| #define OMAP1510_GPIO_DATA_OUTPUT 0x04 |
| #define OMAP1510_GPIO_DIR_CONTROL 0x08 |
| #define OMAP1510_GPIO_INT_CONTROL 0x0c |
| #define OMAP1510_GPIO_INT_MASK 0x10 |
| #define OMAP1510_GPIO_INT_STATUS 0x14 |
| #define OMAP1510_GPIO_PIN_CONTROL 0x18 |
| |
| #define OMAP1510_IH_GPIO_BASE 64 |
| |
| /* |
| * OMAP1610 specific GPIO registers |
| */ |
| #define OMAP1610_GPIO1_BASE 0xfffbe400 |
| #define OMAP1610_GPIO2_BASE 0xfffbec00 |
| #define OMAP1610_GPIO3_BASE 0xfffbb400 |
| #define OMAP1610_GPIO4_BASE 0xfffbbc00 |
| #define OMAP1610_GPIO_REVISION 0x0000 |
| #define OMAP1610_GPIO_SYSCONFIG 0x0010 |
| #define OMAP1610_GPIO_SYSSTATUS 0x0014 |
| #define OMAP1610_GPIO_IRQSTATUS1 0x0018 |
| #define OMAP1610_GPIO_IRQENABLE1 0x001c |
| #define OMAP1610_GPIO_WAKEUPENABLE 0x0028 |
| #define OMAP1610_GPIO_DATAIN 0x002c |
| #define OMAP1610_GPIO_DATAOUT 0x0030 |
| #define OMAP1610_GPIO_DIRECTION 0x0034 |
| #define OMAP1610_GPIO_EDGE_CTRL1 0x0038 |
| #define OMAP1610_GPIO_EDGE_CTRL2 0x003c |
| #define OMAP1610_GPIO_CLEAR_IRQENABLE1 0x009c |
| #define OMAP1610_GPIO_CLEAR_WAKEUPENA 0x00a8 |
| #define OMAP1610_GPIO_CLEAR_DATAOUT 0x00b0 |
| #define OMAP1610_GPIO_SET_IRQENABLE1 0x00dc |
| #define OMAP1610_GPIO_SET_WAKEUPENA 0x00e8 |
| #define OMAP1610_GPIO_SET_DATAOUT 0x00f0 |
| |
| /* |
| * OMAP7XX specific GPIO registers |
| */ |
| #define OMAP7XX_GPIO1_BASE 0xfffbc000 |
| #define OMAP7XX_GPIO2_BASE 0xfffbc800 |
| #define OMAP7XX_GPIO3_BASE 0xfffbd000 |
| #define OMAP7XX_GPIO4_BASE 0xfffbd800 |
| #define OMAP7XX_GPIO5_BASE 0xfffbe000 |
| #define OMAP7XX_GPIO6_BASE 0xfffbe800 |
| #define OMAP7XX_GPIO_DATA_INPUT 0x00 |
| #define OMAP7XX_GPIO_DATA_OUTPUT 0x04 |
| #define OMAP7XX_GPIO_DIR_CONTROL 0x08 |
| #define OMAP7XX_GPIO_INT_CONTROL 0x0c |
| #define OMAP7XX_GPIO_INT_MASK 0x10 |
| #define OMAP7XX_GPIO_INT_STATUS 0x14 |
| |
| #define OMAP1_MPUIO_VBASE OMAP1_MPUIO_BASE |
| |
| /* |
| * omap24xx specific GPIO registers |
| */ |
| #define OMAP242X_GPIO1_BASE 0x48018000 |
| #define OMAP242X_GPIO2_BASE 0x4801a000 |
| #define OMAP242X_GPIO3_BASE 0x4801c000 |
| #define OMAP242X_GPIO4_BASE 0x4801e000 |
| |
| #define OMAP243X_GPIO1_BASE 0x4900C000 |
| #define OMAP243X_GPIO2_BASE 0x4900E000 |
| #define OMAP243X_GPIO3_BASE 0x49010000 |
| #define OMAP243X_GPIO4_BASE 0x49012000 |
| #define OMAP243X_GPIO5_BASE 0x480B6000 |
| |
| #define OMAP24XX_GPIO_REVISION 0x0000 |
| #define OMAP24XX_GPIO_SYSCONFIG 0x0010 |
| #define OMAP24XX_GPIO_SYSSTATUS 0x0014 |
| #define OMAP24XX_GPIO_IRQSTATUS1 0x0018 |
| #define OMAP24XX_GPIO_IRQSTATUS2 0x0028 |
| #define OMAP24XX_GPIO_IRQENABLE2 0x002c |
| #define OMAP24XX_GPIO_IRQENABLE1 0x001c |
| #define OMAP24XX_GPIO_WAKE_EN 0x0020 |
| #define OMAP24XX_GPIO_CTRL 0x0030 |
| #define OMAP24XX_GPIO_OE 0x0034 |
| #define OMAP24XX_GPIO_DATAIN 0x0038 |
| #define OMAP24XX_GPIO_DATAOUT 0x003c |
| #define OMAP24XX_GPIO_LEVELDETECT0 0x0040 |
| #define OMAP24XX_GPIO_LEVELDETECT1 0x0044 |
| #define OMAP24XX_GPIO_RISINGDETECT 0x0048 |
| #define OMAP24XX_GPIO_FALLINGDETECT 0x004c |
| #define OMAP24XX_GPIO_DEBOUNCE_EN 0x0050 |
| #define OMAP24XX_GPIO_DEBOUNCE_VAL 0x0054 |
| #define OMAP24XX_GPIO_CLEARIRQENABLE1 0x0060 |
| #define OMAP24XX_GPIO_SETIRQENABLE1 0x0064 |
| #define OMAP24XX_GPIO_CLEARWKUENA 0x0080 |
| #define OMAP24XX_GPIO_SETWKUENA 0x0084 |
| #define OMAP24XX_GPIO_CLEARDATAOUT 0x0090 |
| #define OMAP24XX_GPIO_SETDATAOUT 0x0094 |
| |
| #define OMAP4_GPIO_REVISION 0x0000 |
| #define OMAP4_GPIO_SYSCONFIG 0x0010 |
| #define OMAP4_GPIO_EOI 0x0020 |
| #define OMAP4_GPIO_IRQSTATUSRAW0 0x0024 |
| #define OMAP4_GPIO_IRQSTATUSRAW1 0x0028 |
| #define OMAP4_GPIO_IRQSTATUS0 0x002c |
| #define OMAP4_GPIO_IRQSTATUS1 0x0030 |
| #define OMAP4_GPIO_IRQSTATUSSET0 0x0034 |
| #define OMAP4_GPIO_IRQSTATUSSET1 0x0038 |
| #define OMAP4_GPIO_IRQSTATUSCLR0 0x003c |
| #define OMAP4_GPIO_IRQSTATUSCLR1 0x0040 |
| #define OMAP4_GPIO_IRQWAKEN0 0x0044 |
| #define OMAP4_GPIO_IRQWAKEN1 0x0048 |
| #define OMAP4_GPIO_SYSSTATUS 0x0114 |
| #define OMAP4_GPIO_IRQENABLE1 0x011c |
| #define OMAP4_GPIO_WAKE_EN 0x0120 |
| #define OMAP4_GPIO_IRQSTATUS2 0x0128 |
| #define OMAP4_GPIO_IRQENABLE2 0x012c |
| #define OMAP4_GPIO_CTRL 0x0130 |
| #define OMAP4_GPIO_OE 0x0134 |
| #define OMAP4_GPIO_DATAIN 0x0138 |
| #define OMAP4_GPIO_DATAOUT 0x013c |
| #define OMAP4_GPIO_LEVELDETECT0 0x0140 |
| #define OMAP4_GPIO_LEVELDETECT1 0x0144 |
| #define OMAP4_GPIO_RISINGDETECT 0x0148 |
| #define OMAP4_GPIO_FALLINGDETECT 0x014c |
| #define OMAP4_GPIO_DEBOUNCENABLE 0x0150 |
| #define OMAP4_GPIO_DEBOUNCINGTIME 0x0154 |
| #define OMAP4_GPIO_CLEARIRQENABLE1 0x0160 |
| #define OMAP4_GPIO_SETIRQENABLE1 0x0164 |
| #define OMAP4_GPIO_CLEARWKUENA 0x0180 |
| #define OMAP4_GPIO_SETWKUENA 0x0184 |
| #define OMAP4_GPIO_CLEARDATAOUT 0x0190 |
| #define OMAP4_GPIO_SETDATAOUT 0x0194 |
| /* |
| * omap34xx specific GPIO registers |
| */ |
| |
| #define OMAP34XX_GPIO1_BASE 0x48310000 |
| #define OMAP34XX_GPIO2_BASE 0x49050000 |
| #define OMAP34XX_GPIO3_BASE 0x49052000 |
| #define OMAP34XX_GPIO4_BASE 0x49054000 |
| #define OMAP34XX_GPIO5_BASE 0x49056000 |
| #define OMAP34XX_GPIO6_BASE 0x49058000 |
| |
| /* |
| * OMAP44XX specific GPIO registers |
| */ |
| #define OMAP44XX_GPIO1_BASE 0x4a310000 |
| #define OMAP44XX_GPIO2_BASE 0x48055000 |
| #define OMAP44XX_GPIO3_BASE 0x48057000 |
| #define OMAP44XX_GPIO4_BASE 0x48059000 |
| #define OMAP44XX_GPIO5_BASE 0x4805B000 |
| #define OMAP44XX_GPIO6_BASE 0x4805D000 |
| |
| struct gpio_bank { |
| unsigned long pbase; |
| void __iomem *base; |
| u16 irq; |
| u16 virtual_irq_start; |
| int method; |
| #if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP2PLUS) |
| u32 suspend_wakeup; |
| u32 saved_wakeup; |
| #endif |
| #ifdef CONFIG_ARCH_OMAP2PLUS |
| u32 non_wakeup_gpios; |
| u32 enabled_non_wakeup_gpios; |
| |
| u32 saved_datain; |
| u32 saved_fallingdetect; |
| u32 saved_risingdetect; |
| #endif |
| u32 level_mask; |
| u32 toggle_mask; |
| spinlock_t lock; |
| struct gpio_chip chip; |
| struct clk *dbck; |
| u32 mod_usage; |
| u32 dbck_enable_mask; |
| }; |
| |
| #define METHOD_MPUIO 0 |
| #define METHOD_GPIO_1510 1 |
| #define METHOD_GPIO_1610 2 |
| #define METHOD_GPIO_7XX 3 |
| #define METHOD_GPIO_24XX 5 |
| #define METHOD_GPIO_44XX 6 |
| |
| #ifdef CONFIG_ARCH_OMAP16XX |
| static struct gpio_bank gpio_bank_1610[5] = { |
| { OMAP1_MPUIO_VBASE, NULL, INT_MPUIO, IH_MPUIO_BASE, |
| METHOD_MPUIO }, |
| { OMAP1610_GPIO1_BASE, NULL, INT_GPIO_BANK1, IH_GPIO_BASE, |
| METHOD_GPIO_1610 }, |
| { OMAP1610_GPIO2_BASE, NULL, INT_1610_GPIO_BANK2, IH_GPIO_BASE + 16, |
| METHOD_GPIO_1610 }, |
| { OMAP1610_GPIO3_BASE, NULL, INT_1610_GPIO_BANK3, IH_GPIO_BASE + 32, |
| METHOD_GPIO_1610 }, |
| { OMAP1610_GPIO4_BASE, NULL, INT_1610_GPIO_BANK4, IH_GPIO_BASE + 48, |
| METHOD_GPIO_1610 }, |
| }; |
| #endif |
| |
| #ifdef CONFIG_ARCH_OMAP15XX |
| static struct gpio_bank gpio_bank_1510[2] = { |
| { OMAP1_MPUIO_VBASE, NULL, INT_MPUIO, IH_MPUIO_BASE, |
| METHOD_MPUIO }, |
| { OMAP1510_GPIO_BASE, NULL, INT_GPIO_BANK1, IH_GPIO_BASE, |
| METHOD_GPIO_1510 } |
| }; |
| #endif |
| |
| #if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850) |
| static struct gpio_bank gpio_bank_7xx[7] = { |
| { OMAP1_MPUIO_VBASE, NULL, INT_7XX_MPUIO, IH_MPUIO_BASE, |
| METHOD_MPUIO }, |
| { OMAP7XX_GPIO1_BASE, NULL, INT_7XX_GPIO_BANK1, IH_GPIO_BASE, |
| METHOD_GPIO_7XX }, |
| { OMAP7XX_GPIO2_BASE, NULL, INT_7XX_GPIO_BANK2, IH_GPIO_BASE + 32, |
| METHOD_GPIO_7XX }, |
| { OMAP7XX_GPIO3_BASE, NULL, INT_7XX_GPIO_BANK3, IH_GPIO_BASE + 64, |
| METHOD_GPIO_7XX }, |
| { OMAP7XX_GPIO4_BASE, NULL, INT_7XX_GPIO_BANK4, IH_GPIO_BASE + 96, |
| METHOD_GPIO_7XX }, |
| { OMAP7XX_GPIO5_BASE, NULL, INT_7XX_GPIO_BANK5, IH_GPIO_BASE + 128, |
| METHOD_GPIO_7XX }, |
| { OMAP7XX_GPIO6_BASE, NULL, INT_7XX_GPIO_BANK6, IH_GPIO_BASE + 160, |
| METHOD_GPIO_7XX }, |
| }; |
| #endif |
| |
| #ifdef CONFIG_ARCH_OMAP2 |
| |
| static struct gpio_bank gpio_bank_242x[4] = { |
| { OMAP242X_GPIO1_BASE, NULL, INT_24XX_GPIO_BANK1, IH_GPIO_BASE, |
| METHOD_GPIO_24XX }, |
| { OMAP242X_GPIO2_BASE, NULL, INT_24XX_GPIO_BANK2, IH_GPIO_BASE + 32, |
| METHOD_GPIO_24XX }, |
| { OMAP242X_GPIO3_BASE, NULL, INT_24XX_GPIO_BANK3, IH_GPIO_BASE + 64, |
| METHOD_GPIO_24XX }, |
| { OMAP242X_GPIO4_BASE, NULL, INT_24XX_GPIO_BANK4, IH_GPIO_BASE + 96, |
| METHOD_GPIO_24XX }, |
| }; |
| |
| static struct gpio_bank gpio_bank_243x[5] = { |
| { OMAP243X_GPIO1_BASE, NULL, INT_24XX_GPIO_BANK1, IH_GPIO_BASE, |
| METHOD_GPIO_24XX }, |
| { OMAP243X_GPIO2_BASE, NULL, INT_24XX_GPIO_BANK2, IH_GPIO_BASE + 32, |
| METHOD_GPIO_24XX }, |
| { OMAP243X_GPIO3_BASE, NULL, INT_24XX_GPIO_BANK3, IH_GPIO_BASE + 64, |
| METHOD_GPIO_24XX }, |
| { OMAP243X_GPIO4_BASE, NULL, INT_24XX_GPIO_BANK4, IH_GPIO_BASE + 96, |
| METHOD_GPIO_24XX }, |
| { OMAP243X_GPIO5_BASE, NULL, INT_24XX_GPIO_BANK5, IH_GPIO_BASE + 128, |
| METHOD_GPIO_24XX }, |
| }; |
| |
| #endif |
| |
| #ifdef CONFIG_ARCH_OMAP3 |
| static struct gpio_bank gpio_bank_34xx[6] = { |
| { OMAP34XX_GPIO1_BASE, NULL, INT_34XX_GPIO_BANK1, IH_GPIO_BASE, |
| METHOD_GPIO_24XX }, |
| { OMAP34XX_GPIO2_BASE, NULL, INT_34XX_GPIO_BANK2, IH_GPIO_BASE + 32, |
| METHOD_GPIO_24XX }, |
| { OMAP34XX_GPIO3_BASE, NULL, INT_34XX_GPIO_BANK3, IH_GPIO_BASE + 64, |
| METHOD_GPIO_24XX }, |
| { OMAP34XX_GPIO4_BASE, NULL, INT_34XX_GPIO_BANK4, IH_GPIO_BASE + 96, |
| METHOD_GPIO_24XX }, |
| { OMAP34XX_GPIO5_BASE, NULL, INT_34XX_GPIO_BANK5, IH_GPIO_BASE + 128, |
| METHOD_GPIO_24XX }, |
| { OMAP34XX_GPIO6_BASE, NULL, INT_34XX_GPIO_BANK6, IH_GPIO_BASE + 160, |
| METHOD_GPIO_24XX }, |
| }; |
| |
| struct omap3_gpio_regs { |
| u32 sysconfig; |
| u32 irqenable1; |
| u32 irqenable2; |
| u32 wake_en; |
| u32 ctrl; |
| u32 oe; |
| u32 leveldetect0; |
| u32 leveldetect1; |
| u32 risingdetect; |
| u32 fallingdetect; |
| u32 dataout; |
| }; |
| |
| static struct omap3_gpio_regs gpio_context[OMAP34XX_NR_GPIOS]; |
| #endif |
| |
| #ifdef CONFIG_ARCH_OMAP4 |
| static struct gpio_bank gpio_bank_44xx[6] = { |
| { OMAP44XX_GPIO1_BASE, NULL, OMAP44XX_IRQ_GPIO1, IH_GPIO_BASE, |
| METHOD_GPIO_44XX }, |
| { OMAP44XX_GPIO2_BASE, NULL, OMAP44XX_IRQ_GPIO2, IH_GPIO_BASE + 32, |
| METHOD_GPIO_44XX }, |
| { OMAP44XX_GPIO3_BASE, NULL, OMAP44XX_IRQ_GPIO3, IH_GPIO_BASE + 64, |
| METHOD_GPIO_44XX }, |
| { OMAP44XX_GPIO4_BASE, NULL, OMAP44XX_IRQ_GPIO4, IH_GPIO_BASE + 96, |
| METHOD_GPIO_44XX }, |
| { OMAP44XX_GPIO5_BASE, NULL, OMAP44XX_IRQ_GPIO5, IH_GPIO_BASE + 128, |
| METHOD_GPIO_44XX }, |
| { OMAP44XX_GPIO6_BASE, NULL, OMAP44XX_IRQ_GPIO6, IH_GPIO_BASE + 160, |
| METHOD_GPIO_44XX }, |
| }; |
| |
| #endif |
| |
| static struct gpio_bank *gpio_bank; |
| static int gpio_bank_count; |
| |
| static inline struct gpio_bank *get_gpio_bank(int gpio) |
| { |
| if (cpu_is_omap15xx()) { |
| if (OMAP_GPIO_IS_MPUIO(gpio)) |
| return &gpio_bank[0]; |
| return &gpio_bank[1]; |
| } |
| if (cpu_is_omap16xx()) { |
| if (OMAP_GPIO_IS_MPUIO(gpio)) |
| return &gpio_bank[0]; |
| return &gpio_bank[1 + (gpio >> 4)]; |
| } |
| if (cpu_is_omap7xx()) { |
| if (OMAP_GPIO_IS_MPUIO(gpio)) |
| return &gpio_bank[0]; |
| return &gpio_bank[1 + (gpio >> 5)]; |
| } |
| if (cpu_is_omap24xx()) |
| return &gpio_bank[gpio >> 5]; |
| if (cpu_is_omap34xx() || cpu_is_omap44xx()) |
| return &gpio_bank[gpio >> 5]; |
| BUG(); |
| return NULL; |
| } |
| |
| static inline int get_gpio_index(int gpio) |
| { |
| if (cpu_is_omap7xx()) |
| return gpio & 0x1f; |
| if (cpu_is_omap24xx()) |
| return gpio & 0x1f; |
| if (cpu_is_omap34xx() || cpu_is_omap44xx()) |
| return gpio & 0x1f; |
| return gpio & 0x0f; |
| } |
| |
| static inline int gpio_valid(int gpio) |
| { |
| if (gpio < 0) |
| return -1; |
| if (cpu_class_is_omap1() && OMAP_GPIO_IS_MPUIO(gpio)) { |
| if (gpio >= OMAP_MAX_GPIO_LINES + 16) |
| return -1; |
| return 0; |
| } |
| if (cpu_is_omap15xx() && gpio < 16) |
| return 0; |
| if ((cpu_is_omap16xx()) && gpio < 64) |
| return 0; |
| if (cpu_is_omap7xx() && gpio < 192) |
| return 0; |
| if (cpu_is_omap24xx() && gpio < 128) |
| return 0; |
| if ((cpu_is_omap34xx() || cpu_is_omap44xx()) && gpio < 192) |
| return 0; |
| return -1; |
| } |
| |
| static int check_gpio(int gpio) |
| { |
| if (unlikely(gpio_valid(gpio) < 0)) { |
| printk(KERN_ERR "omap-gpio: invalid GPIO %d\n", gpio); |
| dump_stack(); |
| return -1; |
| } |
| return 0; |
| } |
| |
| static void _set_gpio_direction(struct gpio_bank *bank, int gpio, int is_input) |
| { |
| void __iomem *reg = bank->base; |
| u32 l; |
| |
| switch (bank->method) { |
| #ifdef CONFIG_ARCH_OMAP1 |
| case METHOD_MPUIO: |
| reg += OMAP_MPUIO_IO_CNTL; |
| break; |
| #endif |
| #ifdef CONFIG_ARCH_OMAP15XX |
| case METHOD_GPIO_1510: |
| reg += OMAP1510_GPIO_DIR_CONTROL; |
| break; |
| #endif |
| #ifdef CONFIG_ARCH_OMAP16XX |
| case METHOD_GPIO_1610: |
| reg += OMAP1610_GPIO_DIRECTION; |
| break; |
| #endif |
| #if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850) |
| case METHOD_GPIO_7XX: |
| reg += OMAP7XX_GPIO_DIR_CONTROL; |
| break; |
| #endif |
| #if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) |
| case METHOD_GPIO_24XX: |
| reg += OMAP24XX_GPIO_OE; |
| break; |
| #endif |
| #if defined(CONFIG_ARCH_OMAP4) |
| case METHOD_GPIO_44XX: |
| reg += OMAP4_GPIO_OE; |
| break; |
| #endif |
| default: |
| WARN_ON(1); |
| return; |
| } |
| l = __raw_readl(reg); |
| if (is_input) |
| l |= 1 << gpio; |
| else |
| l &= ~(1 << gpio); |
| __raw_writel(l, reg); |
| } |
| |
| static void _set_gpio_dataout(struct gpio_bank *bank, int gpio, int enable) |
| { |
| void __iomem *reg = bank->base; |
| u32 l = 0; |
| |
| switch (bank->method) { |
| #ifdef CONFIG_ARCH_OMAP1 |
| case METHOD_MPUIO: |
| reg += OMAP_MPUIO_OUTPUT; |
| l = __raw_readl(reg); |
| if (enable) |
| l |= 1 << gpio; |
| else |
| l &= ~(1 << gpio); |
| break; |
| #endif |
| #ifdef CONFIG_ARCH_OMAP15XX |
| case METHOD_GPIO_1510: |
| reg += OMAP1510_GPIO_DATA_OUTPUT; |
| l = __raw_readl(reg); |
| if (enable) |
| l |= 1 << gpio; |
| else |
| l &= ~(1 << gpio); |
| break; |
| #endif |
| #ifdef CONFIG_ARCH_OMAP16XX |
| case METHOD_GPIO_1610: |
| if (enable) |
| reg += OMAP1610_GPIO_SET_DATAOUT; |
| else |
| reg += OMAP1610_GPIO_CLEAR_DATAOUT; |
| l = 1 << gpio; |
| break; |
| #endif |
| #if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850) |
| case METHOD_GPIO_7XX: |
| reg += OMAP7XX_GPIO_DATA_OUTPUT; |
| l = __raw_readl(reg); |
| if (enable) |
| l |= 1 << gpio; |
| else |
| l &= ~(1 << gpio); |
| break; |
| #endif |
| #if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) |
| case METHOD_GPIO_24XX: |
| if (enable) |
| reg += OMAP24XX_GPIO_SETDATAOUT; |
| else |
| reg += OMAP24XX_GPIO_CLEARDATAOUT; |
| l = 1 << gpio; |
| break; |
| #endif |
| #ifdef CONFIG_ARCH_OMAP4 |
| case METHOD_GPIO_44XX: |
| if (enable) |
| reg += OMAP4_GPIO_SETDATAOUT; |
| else |
| reg += OMAP4_GPIO_CLEARDATAOUT; |
| l = 1 << gpio; |
| break; |
| #endif |
| default: |
| WARN_ON(1); |
| return; |
| } |
| __raw_writel(l, reg); |
| } |
| |
| static int _get_gpio_datain(struct gpio_bank *bank, int gpio) |
| { |
| void __iomem *reg; |
| |
| if (check_gpio(gpio) < 0) |
| return -EINVAL; |
| reg = bank->base; |
| switch (bank->method) { |
| #ifdef CONFIG_ARCH_OMAP1 |
| case METHOD_MPUIO: |
| reg += OMAP_MPUIO_INPUT_LATCH; |
| break; |
| #endif |
| #ifdef CONFIG_ARCH_OMAP15XX |
| case METHOD_GPIO_1510: |
| reg += OMAP1510_GPIO_DATA_INPUT; |
| break; |
| #endif |
| #ifdef CONFIG_ARCH_OMAP16XX |
| case METHOD_GPIO_1610: |
| reg += OMAP1610_GPIO_DATAIN; |
| break; |
| #endif |
| #if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850) |
| case METHOD_GPIO_7XX: |
| reg += OMAP7XX_GPIO_DATA_INPUT; |
| break; |
| #endif |
| #if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) |
| case METHOD_GPIO_24XX: |
| reg += OMAP24XX_GPIO_DATAIN; |
| break; |
| #endif |
| #ifdef CONFIG_ARCH_OMAP4 |
| case METHOD_GPIO_44XX: |
| reg += OMAP4_GPIO_DATAIN; |
| break; |
| #endif |
| default: |
| return -EINVAL; |
| } |
| return (__raw_readl(reg) |
| & (1 << get_gpio_index(gpio))) != 0; |
| } |
| |
| static int _get_gpio_dataout(struct gpio_bank *bank, int gpio) |
| { |
| void __iomem *reg; |
| |
| if (check_gpio(gpio) < 0) |
| return -EINVAL; |
| reg = bank->base; |
| |
| switch (bank->method) { |
| #ifdef CONFIG_ARCH_OMAP1 |
| case METHOD_MPUIO: |
| reg += OMAP_MPUIO_OUTPUT; |
| break; |
| #endif |
| #ifdef CONFIG_ARCH_OMAP15XX |
| case METHOD_GPIO_1510: |
| reg += OMAP1510_GPIO_DATA_OUTPUT; |
| break; |
| #endif |
| #ifdef CONFIG_ARCH_OMAP16XX |
| case METHOD_GPIO_1610: |
| reg += OMAP1610_GPIO_DATAOUT; |
| break; |
| #endif |
| #if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850) |
| case METHOD_GPIO_7XX: |
| reg += OMAP7XX_GPIO_DATA_OUTPUT; |
| break; |
| #endif |
| #if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) |
| case METHOD_GPIO_24XX: |
| reg += OMAP24XX_GPIO_DATAOUT; |
| break; |
| #endif |
| #ifdef CONFIG_ARCH_OMAP4 |
| case METHOD_GPIO_44XX: |
| reg += OMAP4_GPIO_DATAOUT; |
| break; |
| #endif |
| default: |
| return -EINVAL; |
| } |
| |
| return (__raw_readl(reg) & (1 << get_gpio_index(gpio))) != 0; |
| } |
| |
| #define MOD_REG_BIT(reg, bit_mask, set) \ |
| do { \ |
| int l = __raw_readl(base + reg); \ |
| if (set) l |= bit_mask; \ |
| else l &= ~bit_mask; \ |
| __raw_writel(l, base + reg); \ |
| } while(0) |
| |
| /** |
| * _set_gpio_debounce - low level gpio debounce time |
| * @bank: the gpio bank we're acting upon |
| * @gpio: the gpio number on this @gpio |
| * @debounce: debounce time to use |
| * |
| * OMAP's debounce time is in 31us steps so we need |
| * to convert and round up to the closest unit. |
| */ |
| static void _set_gpio_debounce(struct gpio_bank *bank, unsigned gpio, |
| unsigned debounce) |
| { |
| void __iomem *reg = bank->base; |
| u32 val; |
| u32 l; |
| |
| if (debounce < 32) |
| debounce = 0x01; |
| else if (debounce > 7936) |
| debounce = 0xff; |
| else |
| debounce = (debounce / 0x1f) - 1; |
| |
| l = 1 << get_gpio_index(gpio); |
| |
| if (cpu_is_omap44xx()) |
| reg += OMAP4_GPIO_DEBOUNCINGTIME; |
| else |
| reg += OMAP24XX_GPIO_DEBOUNCE_VAL; |
| |
| __raw_writel(debounce, reg); |
| |
| reg = bank->base; |
| if (cpu_is_omap44xx()) |
| reg += OMAP4_GPIO_DEBOUNCENABLE; |
| else |
| reg += OMAP24XX_GPIO_DEBOUNCE_EN; |
| |
| val = __raw_readl(reg); |
| |
| if (debounce) { |
| val |= l; |
| if (cpu_is_omap34xx() || cpu_is_omap44xx()) |
| clk_enable(bank->dbck); |
| } else { |
| val &= ~l; |
| if (cpu_is_omap34xx() || cpu_is_omap44xx()) |
| clk_disable(bank->dbck); |
| } |
| |
| __raw_writel(val, reg); |
| } |
| |
| void omap_set_gpio_debounce(int gpio, int enable) |
| { |
| struct gpio_bank *bank; |
| void __iomem *reg; |
| unsigned long flags; |
| u32 val, l = 1 << get_gpio_index(gpio); |
| |
| if (cpu_class_is_omap1()) |
| return; |
| |
| bank = get_gpio_bank(gpio); |
| reg = bank->base; |
| |
| if (cpu_is_omap44xx()) |
| reg += OMAP4_GPIO_DEBOUNCENABLE; |
| else |
| reg += OMAP24XX_GPIO_DEBOUNCE_EN; |
| |
| if (!(bank->mod_usage & l)) { |
| printk(KERN_ERR "GPIO %d not requested\n", gpio); |
| return; |
| } |
| |
| spin_lock_irqsave(&bank->lock, flags); |
| val = __raw_readl(reg); |
| |
| if (enable && !(val & l)) |
| val |= l; |
| else if (!enable && (val & l)) |
| val &= ~l; |
| else |
| goto done; |
| |
| if (cpu_is_omap34xx() || cpu_is_omap44xx()) { |
| bank->dbck_enable_mask = val; |
| if (enable) |
| clk_enable(bank->dbck); |
| else |
| clk_disable(bank->dbck); |
| } |
| |
| __raw_writel(val, reg); |
| done: |
| spin_unlock_irqrestore(&bank->lock, flags); |
| } |
| EXPORT_SYMBOL(omap_set_gpio_debounce); |
| |
| void omap_set_gpio_debounce_time(int gpio, int enc_time) |
| { |
| struct gpio_bank *bank; |
| void __iomem *reg; |
| |
| if (cpu_class_is_omap1()) |
| return; |
| |
| bank = get_gpio_bank(gpio); |
| reg = bank->base; |
| |
| if (!bank->mod_usage) { |
| printk(KERN_ERR "GPIO not requested\n"); |
| return; |
| } |
| |
| enc_time &= 0xff; |
| |
| if (cpu_is_omap44xx()) |
| reg += OMAP4_GPIO_DEBOUNCINGTIME; |
| else |
| reg += OMAP24XX_GPIO_DEBOUNCE_VAL; |
| |
| __raw_writel(enc_time, reg); |
| } |
| EXPORT_SYMBOL(omap_set_gpio_debounce_time); |
| |
| #ifdef CONFIG_ARCH_OMAP2PLUS |
| static inline void set_24xx_gpio_triggering(struct gpio_bank *bank, int gpio, |
| int trigger) |
| { |
| void __iomem *base = bank->base; |
| u32 gpio_bit = 1 << gpio; |
| u32 val; |
| |
| if (cpu_is_omap44xx()) { |
| MOD_REG_BIT(OMAP4_GPIO_LEVELDETECT0, gpio_bit, |
| trigger & IRQ_TYPE_LEVEL_LOW); |
| MOD_REG_BIT(OMAP4_GPIO_LEVELDETECT1, gpio_bit, |
| trigger & IRQ_TYPE_LEVEL_HIGH); |
| MOD_REG_BIT(OMAP4_GPIO_RISINGDETECT, gpio_bit, |
| trigger & IRQ_TYPE_EDGE_RISING); |
| MOD_REG_BIT(OMAP4_GPIO_FALLINGDETECT, gpio_bit, |
| trigger & IRQ_TYPE_EDGE_FALLING); |
| } else { |
| MOD_REG_BIT(OMAP24XX_GPIO_LEVELDETECT0, gpio_bit, |
| trigger & IRQ_TYPE_LEVEL_LOW); |
| MOD_REG_BIT(OMAP24XX_GPIO_LEVELDETECT1, gpio_bit, |
| trigger & IRQ_TYPE_LEVEL_HIGH); |
| MOD_REG_BIT(OMAP24XX_GPIO_RISINGDETECT, gpio_bit, |
| trigger & IRQ_TYPE_EDGE_RISING); |
| MOD_REG_BIT(OMAP24XX_GPIO_FALLINGDETECT, gpio_bit, |
| trigger & IRQ_TYPE_EDGE_FALLING); |
| } |
| if (likely(!(bank->non_wakeup_gpios & gpio_bit))) { |
| if (cpu_is_omap44xx()) { |
| if (trigger != 0) |
| __raw_writel(1 << gpio, bank->base+ |
| OMAP4_GPIO_IRQWAKEN0); |
| else { |
| val = __raw_readl(bank->base + |
| OMAP4_GPIO_IRQWAKEN0); |
| __raw_writel(val & (~(1 << gpio)), bank->base + |
| OMAP4_GPIO_IRQWAKEN0); |
| } |
| } else { |
| /* |
| * GPIO wakeup request can only be generated on edge |
| * transitions |
| */ |
| if (trigger & IRQ_TYPE_EDGE_BOTH) |
| __raw_writel(1 << gpio, bank->base |
| + OMAP24XX_GPIO_SETWKUENA); |
| else |
| __raw_writel(1 << gpio, bank->base |
| + OMAP24XX_GPIO_CLEARWKUENA); |
| } |
| } |
| /* This part needs to be executed always for OMAP34xx */ |
| if (cpu_is_omap34xx() || (bank->non_wakeup_gpios & gpio_bit)) { |
| /* |
| * Log the edge gpio and manually trigger the IRQ |
| * after resume if the input level changes |
| * to avoid irq lost during PER RET/OFF mode |
| * Applies for omap2 non-wakeup gpio and all omap3 gpios |
| */ |
| if (trigger & IRQ_TYPE_EDGE_BOTH) |
| bank->enabled_non_wakeup_gpios |= gpio_bit; |
| else |
| bank->enabled_non_wakeup_gpios &= ~gpio_bit; |
| } |
| |
| if (cpu_is_omap44xx()) { |
| bank->level_mask = |
| __raw_readl(bank->base + OMAP4_GPIO_LEVELDETECT0) | |
| __raw_readl(bank->base + OMAP4_GPIO_LEVELDETECT1); |
| } else { |
| bank->level_mask = |
| __raw_readl(bank->base + OMAP24XX_GPIO_LEVELDETECT0) | |
| __raw_readl(bank->base + OMAP24XX_GPIO_LEVELDETECT1); |
| } |
| } |
| #endif |
| |
| #ifdef CONFIG_ARCH_OMAP1 |
| /* |
| * This only applies to chips that can't do both rising and falling edge |
| * detection at once. For all other chips, this function is a noop. |
| */ |
| static void _toggle_gpio_edge_triggering(struct gpio_bank *bank, int gpio) |
| { |
| void __iomem *reg = bank->base; |
| u32 l = 0; |
| |
| switch (bank->method) { |
| case METHOD_MPUIO: |
| reg += OMAP_MPUIO_GPIO_INT_EDGE; |
| break; |
| #ifdef CONFIG_ARCH_OMAP15XX |
| case METHOD_GPIO_1510: |
| reg += OMAP1510_GPIO_INT_CONTROL; |
| break; |
| #endif |
| #if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850) |
| case METHOD_GPIO_7XX: |
| reg += OMAP7XX_GPIO_INT_CONTROL; |
| break; |
| #endif |
| default: |
| return; |
| } |
| |
| l = __raw_readl(reg); |
| if ((l >> gpio) & 1) |
| l &= ~(1 << gpio); |
| else |
| l |= 1 << gpio; |
| |
| __raw_writel(l, reg); |
| } |
| #endif |
| |
| static int _set_gpio_triggering(struct gpio_bank *bank, int gpio, int trigger) |
| { |
| void __iomem *reg = bank->base; |
| u32 l = 0; |
| |
| switch (bank->method) { |
| #ifdef CONFIG_ARCH_OMAP1 |
| case METHOD_MPUIO: |
| reg += OMAP_MPUIO_GPIO_INT_EDGE; |
| l = __raw_readl(reg); |
| if ((trigger & IRQ_TYPE_SENSE_MASK) == IRQ_TYPE_EDGE_BOTH) |
| bank->toggle_mask |= 1 << gpio; |
| if (trigger & IRQ_TYPE_EDGE_RISING) |
| l |= 1 << gpio; |
| else if (trigger & IRQ_TYPE_EDGE_FALLING) |
| l &= ~(1 << gpio); |
| else |
| goto bad; |
| break; |
| #endif |
| #ifdef CONFIG_ARCH_OMAP15XX |
| case METHOD_GPIO_1510: |
| reg += OMAP1510_GPIO_INT_CONTROL; |
| l = __raw_readl(reg); |
| if ((trigger & IRQ_TYPE_SENSE_MASK) == IRQ_TYPE_EDGE_BOTH) |
| bank->toggle_mask |= 1 << gpio; |
| if (trigger & IRQ_TYPE_EDGE_RISING) |
| l |= 1 << gpio; |
| else if (trigger & IRQ_TYPE_EDGE_FALLING) |
| l &= ~(1 << gpio); |
| else |
| goto bad; |
| break; |
| #endif |
| #ifdef CONFIG_ARCH_OMAP16XX |
| case METHOD_GPIO_1610: |
| if (gpio & 0x08) |
| reg += OMAP1610_GPIO_EDGE_CTRL2; |
| else |
| reg += OMAP1610_GPIO_EDGE_CTRL1; |
| gpio &= 0x07; |
| l = __raw_readl(reg); |
| l &= ~(3 << (gpio << 1)); |
| if (trigger & IRQ_TYPE_EDGE_RISING) |
| l |= 2 << (gpio << 1); |
| if (trigger & IRQ_TYPE_EDGE_FALLING) |
| l |= 1 << (gpio << 1); |
| if (trigger) |
| /* Enable wake-up during idle for dynamic tick */ |
| __raw_writel(1 << gpio, bank->base + OMAP1610_GPIO_SET_WAKEUPENA); |
| else |
| __raw_writel(1 << gpio, bank->base + OMAP1610_GPIO_CLEAR_WAKEUPENA); |
| break; |
| #endif |
| #if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850) |
| case METHOD_GPIO_7XX: |
| reg += OMAP7XX_GPIO_INT_CONTROL; |
| l = __raw_readl(reg); |
| if ((trigger & IRQ_TYPE_SENSE_MASK) == IRQ_TYPE_EDGE_BOTH) |
| bank->toggle_mask |= 1 << gpio; |
| if (trigger & IRQ_TYPE_EDGE_RISING) |
| l |= 1 << gpio; |
| else if (trigger & IRQ_TYPE_EDGE_FALLING) |
| l &= ~(1 << gpio); |
| else |
| goto bad; |
| break; |
| #endif |
| #ifdef CONFIG_ARCH_OMAP2PLUS |
| case METHOD_GPIO_24XX: |
| case METHOD_GPIO_44XX: |
| set_24xx_gpio_triggering(bank, gpio, trigger); |
| break; |
| #endif |
| default: |
| goto bad; |
| } |
| __raw_writel(l, reg); |
| return 0; |
| bad: |
| return -EINVAL; |
| } |
| |
| static int gpio_irq_type(unsigned irq, unsigned type) |
| { |
| struct gpio_bank *bank; |
| unsigned gpio; |
| int retval; |
| unsigned long flags; |
| |
| if (!cpu_class_is_omap2() && irq > IH_MPUIO_BASE) |
| gpio = OMAP_MPUIO(irq - IH_MPUIO_BASE); |
| else |
| gpio = irq - IH_GPIO_BASE; |
| |
| if (check_gpio(gpio) < 0) |
| return -EINVAL; |
| |
| if (type & ~IRQ_TYPE_SENSE_MASK) |
| return -EINVAL; |
| |
| /* OMAP1 allows only only edge triggering */ |
| if (!cpu_class_is_omap2() |
| && (type & (IRQ_TYPE_LEVEL_LOW|IRQ_TYPE_LEVEL_HIGH))) |
| return -EINVAL; |
| |
| bank = get_irq_chip_data(irq); |
| spin_lock_irqsave(&bank->lock, flags); |
| retval = _set_gpio_triggering(bank, get_gpio_index(gpio), type); |
| if (retval == 0) { |
| irq_desc[irq].status &= ~IRQ_TYPE_SENSE_MASK; |
| irq_desc[irq].status |= type; |
| } |
| spin_unlock_irqrestore(&bank->lock, flags); |
| |
| if (type & (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_LEVEL_HIGH)) |
| __set_irq_handler_unlocked(irq, handle_level_irq); |
| else if (type & (IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_EDGE_RISING)) |
| __set_irq_handler_unlocked(irq, handle_edge_irq); |
| |
| return retval; |
| } |
| |
| static void _clear_gpio_irqbank(struct gpio_bank *bank, int gpio_mask) |
| { |
| void __iomem *reg = bank->base; |
| |
| switch (bank->method) { |
| #ifdef CONFIG_ARCH_OMAP1 |
| case METHOD_MPUIO: |
| /* MPUIO irqstatus is reset by reading the status register, |
| * so do nothing here */ |
| return; |
| #endif |
| #ifdef CONFIG_ARCH_OMAP15XX |
| case METHOD_GPIO_1510: |
| reg += OMAP1510_GPIO_INT_STATUS; |
| break; |
| #endif |
| #ifdef CONFIG_ARCH_OMAP16XX |
| case METHOD_GPIO_1610: |
| reg += OMAP1610_GPIO_IRQSTATUS1; |
| break; |
| #endif |
| #if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850) |
| case METHOD_GPIO_7XX: |
| reg += OMAP7XX_GPIO_INT_STATUS; |
| break; |
| #endif |
| #if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) |
| case METHOD_GPIO_24XX: |
| reg += OMAP24XX_GPIO_IRQSTATUS1; |
| break; |
| #endif |
| #if defined(CONFIG_ARCH_OMAP4) |
| case METHOD_GPIO_44XX: |
| reg += OMAP4_GPIO_IRQSTATUS0; |
| break; |
| #endif |
| default: |
| WARN_ON(1); |
| return; |
| } |
| __raw_writel(gpio_mask, reg); |
| |
| /* Workaround for clearing DSP GPIO interrupts to allow retention */ |
| if (cpu_is_omap24xx() || cpu_is_omap34xx()) |
| reg = bank->base + OMAP24XX_GPIO_IRQSTATUS2; |
| else if (cpu_is_omap44xx()) |
| reg = bank->base + OMAP4_GPIO_IRQSTATUS1; |
| |
| if (cpu_is_omap24xx() || cpu_is_omap34xx() || cpu_is_omap44xx()) { |
| __raw_writel(gpio_mask, reg); |
| |
| /* Flush posted write for the irq status to avoid spurious interrupts */ |
| __raw_readl(reg); |
| } |
| } |
| |
| static inline void _clear_gpio_irqstatus(struct gpio_bank *bank, int gpio) |
| { |
| _clear_gpio_irqbank(bank, 1 << get_gpio_index(gpio)); |
| } |
| |
| static u32 _get_gpio_irqbank_mask(struct gpio_bank *bank) |
| { |
| void __iomem *reg = bank->base; |
| int inv = 0; |
| u32 l; |
| u32 mask; |
| |
| switch (bank->method) { |
| #ifdef CONFIG_ARCH_OMAP1 |
| case METHOD_MPUIO: |
| reg += OMAP_MPUIO_GPIO_MASKIT; |
| mask = 0xffff; |
| inv = 1; |
| break; |
| #endif |
| #ifdef CONFIG_ARCH_OMAP15XX |
| case METHOD_GPIO_1510: |
| reg += OMAP1510_GPIO_INT_MASK; |
| mask = 0xffff; |
| inv = 1; |
| break; |
| #endif |
| #ifdef CONFIG_ARCH_OMAP16XX |
| case METHOD_GPIO_1610: |
| reg += OMAP1610_GPIO_IRQENABLE1; |
| mask = 0xffff; |
| break; |
| #endif |
| #if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850) |
| case METHOD_GPIO_7XX: |
| reg += OMAP7XX_GPIO_INT_MASK; |
| mask = 0xffffffff; |
| inv = 1; |
| break; |
| #endif |
| #if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) |
| case METHOD_GPIO_24XX: |
| reg += OMAP24XX_GPIO_IRQENABLE1; |
| mask = 0xffffffff; |
| break; |
| #endif |
| #if defined(CONFIG_ARCH_OMAP4) |
| case METHOD_GPIO_44XX: |
| reg += OMAP4_GPIO_IRQSTATUSSET0; |
| mask = 0xffffffff; |
| break; |
| #endif |
| default: |
| WARN_ON(1); |
| return 0; |
| } |
| |
| l = __raw_readl(reg); |
| if (inv) |
| l = ~l; |
| l &= mask; |
| return l; |
| } |
| |
| static void _enable_gpio_irqbank(struct gpio_bank *bank, int gpio_mask, int enable) |
| { |
| void __iomem *reg = bank->base; |
| u32 l; |
| |
| switch (bank->method) { |
| #ifdef CONFIG_ARCH_OMAP1 |
| case METHOD_MPUIO: |
| reg += OMAP_MPUIO_GPIO_MASKIT; |
| l = __raw_readl(reg); |
| if (enable) |
| l &= ~(gpio_mask); |
| else |
| l |= gpio_mask; |
| break; |
| #endif |
| #ifdef CONFIG_ARCH_OMAP15XX |
| case METHOD_GPIO_1510: |
| reg += OMAP1510_GPIO_INT_MASK; |
| l = __raw_readl(reg); |
| if (enable) |
| l &= ~(gpio_mask); |
| else |
| l |= gpio_mask; |
| break; |
| #endif |
| #ifdef CONFIG_ARCH_OMAP16XX |
| case METHOD_GPIO_1610: |
| if (enable) |
| reg += OMAP1610_GPIO_SET_IRQENABLE1; |
| else |
| reg += OMAP1610_GPIO_CLEAR_IRQENABLE1; |
| l = gpio_mask; |
| break; |
| #endif |
| #if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850) |
| case METHOD_GPIO_7XX: |
| reg += OMAP7XX_GPIO_INT_MASK; |
| l = __raw_readl(reg); |
| if (enable) |
| l &= ~(gpio_mask); |
| else |
| l |= gpio_mask; |
| break; |
| #endif |
| #if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) |
| case METHOD_GPIO_24XX: |
| if (enable) |
| reg += OMAP24XX_GPIO_SETIRQENABLE1; |
| else |
| reg += OMAP24XX_GPIO_CLEARIRQENABLE1; |
| l = gpio_mask; |
| break; |
| #endif |
| #ifdef CONFIG_ARCH_OMAP4 |
| case METHOD_GPIO_44XX: |
| if (enable) |
| reg += OMAP4_GPIO_IRQSTATUSSET0; |
| else |
| reg += OMAP4_GPIO_IRQSTATUSCLR0; |
| l = gpio_mask; |
| break; |
| #endif |
| default: |
| WARN_ON(1); |
| return; |
| } |
| __raw_writel(l, reg); |
| } |
| |
| static inline void _set_gpio_irqenable(struct gpio_bank *bank, int gpio, int enable) |
| { |
| _enable_gpio_irqbank(bank, 1 << get_gpio_index(gpio), enable); |
| } |
| |
| /* |
| * Note that ENAWAKEUP needs to be enabled in GPIO_SYSCONFIG register. |
| * 1510 does not seem to have a wake-up register. If JTAG is connected |
| * to the target, system will wake up always on GPIO events. While |
| * system is running all registered GPIO interrupts need to have wake-up |
| * enabled. When system is suspended, only selected GPIO interrupts need |
| * to have wake-up enabled. |
| */ |
| static int _set_gpio_wakeup(struct gpio_bank *bank, int gpio, int enable) |
| { |
| unsigned long uninitialized_var(flags); |
| |
| switch (bank->method) { |
| #ifdef CONFIG_ARCH_OMAP16XX |
| case METHOD_MPUIO: |
| case METHOD_GPIO_1610: |
| spin_lock_irqsave(&bank->lock, flags); |
| if (enable) |
| bank->suspend_wakeup |= (1 << gpio); |
| else |
| bank->suspend_wakeup &= ~(1 << gpio); |
| spin_unlock_irqrestore(&bank->lock, flags); |
| return 0; |
| #endif |
| #ifdef CONFIG_ARCH_OMAP2PLUS |
| case METHOD_GPIO_24XX: |
| case METHOD_GPIO_44XX: |
| if (bank->non_wakeup_gpios & (1 << gpio)) { |
| printk(KERN_ERR "Unable to modify wakeup on " |
| "non-wakeup GPIO%d\n", |
| (bank - gpio_bank) * 32 + gpio); |
| return -EINVAL; |
| } |
| spin_lock_irqsave(&bank->lock, flags); |
| if (enable) |
| bank->suspend_wakeup |= (1 << gpio); |
| else |
| bank->suspend_wakeup &= ~(1 << gpio); |
| spin_unlock_irqrestore(&bank->lock, flags); |
| return 0; |
| #endif |
| default: |
| printk(KERN_ERR "Can't enable GPIO wakeup for method %i\n", |
| bank->method); |
| return -EINVAL; |
| } |
| } |
| |
| static void _reset_gpio(struct gpio_bank *bank, int gpio) |
| { |
| _set_gpio_direction(bank, get_gpio_index(gpio), 1); |
| _set_gpio_irqenable(bank, gpio, 0); |
| _clear_gpio_irqstatus(bank, gpio); |
| _set_gpio_triggering(bank, get_gpio_index(gpio), IRQ_TYPE_NONE); |
| } |
| |
| /* Use disable_irq_wake() and enable_irq_wake() functions from drivers */ |
| static int gpio_wake_enable(unsigned int irq, unsigned int enable) |
| { |
| unsigned int gpio = irq - IH_GPIO_BASE; |
| struct gpio_bank *bank; |
| int retval; |
| |
| if (check_gpio(gpio) < 0) |
| return -ENODEV; |
| bank = get_irq_chip_data(irq); |
| retval = _set_gpio_wakeup(bank, get_gpio_index(gpio), enable); |
| |
| return retval; |
| } |
| |
| static int omap_gpio_request(struct gpio_chip *chip, unsigned offset) |
| { |
| struct gpio_bank *bank = container_of(chip, struct gpio_bank, chip); |
| unsigned long flags; |
| |
| spin_lock_irqsave(&bank->lock, flags); |
| |
| /* Set trigger to none. You need to enable the desired trigger with |
| * request_irq() or set_irq_type(). |
| */ |
| _set_gpio_triggering(bank, offset, IRQ_TYPE_NONE); |
| |
| #ifdef CONFIG_ARCH_OMAP15XX |
| if (bank->method == METHOD_GPIO_1510) { |
| void __iomem *reg; |
| |
| /* Claim the pin for MPU */ |
| reg = bank->base + OMAP1510_GPIO_PIN_CONTROL; |
| __raw_writel(__raw_readl(reg) | (1 << offset), reg); |
| } |
| #endif |
| if (!cpu_class_is_omap1()) { |
| if (!bank->mod_usage) { |
| void __iomem *reg = bank->base; |
| u32 ctrl; |
| |
| if (cpu_is_omap24xx() || cpu_is_omap34xx()) |
| reg += OMAP24XX_GPIO_CTRL; |
| else if (cpu_is_omap44xx()) |
| reg += OMAP4_GPIO_CTRL; |
| ctrl = __raw_readl(reg); |
| /* Module is enabled, clocks are not gated */ |
| ctrl &= 0xFFFFFFFE; |
| __raw_writel(ctrl, reg); |
| } |
| bank->mod_usage |= 1 << offset; |
| } |
| spin_unlock_irqrestore(&bank->lock, flags); |
| |
| return 0; |
| } |
| |
| static void omap_gpio_free(struct gpio_chip *chip, unsigned offset) |
| { |
| struct gpio_bank *bank = container_of(chip, struct gpio_bank, chip); |
| unsigned long flags; |
| |
| spin_lock_irqsave(&bank->lock, flags); |
| #ifdef CONFIG_ARCH_OMAP16XX |
| if (bank->method == METHOD_GPIO_1610) { |
| /* Disable wake-up during idle for dynamic tick */ |
| void __iomem *reg = bank->base + OMAP1610_GPIO_CLEAR_WAKEUPENA; |
| __raw_writel(1 << offset, reg); |
| } |
| #endif |
| #if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) |
| if (bank->method == METHOD_GPIO_24XX) { |
| /* Disable wake-up during idle for dynamic tick */ |
| void __iomem *reg = bank->base + OMAP24XX_GPIO_CLEARWKUENA; |
| __raw_writel(1 << offset, reg); |
| } |
| #endif |
| #ifdef CONFIG_ARCH_OMAP4 |
| if (bank->method == METHOD_GPIO_44XX) { |
| /* Disable wake-up during idle for dynamic tick */ |
| void __iomem *reg = bank->base + OMAP4_GPIO_IRQWAKEN0; |
| __raw_writel(1 << offset, reg); |
| } |
| #endif |
| if (!cpu_class_is_omap1()) { |
| bank->mod_usage &= ~(1 << offset); |
| if (!bank->mod_usage) { |
| void __iomem *reg = bank->base; |
| u32 ctrl; |
| |
| if (cpu_is_omap24xx() || cpu_is_omap34xx()) |
| reg += OMAP24XX_GPIO_CTRL; |
| else if (cpu_is_omap44xx()) |
| reg += OMAP4_GPIO_CTRL; |
| ctrl = __raw_readl(reg); |
| /* Module is disabled, clocks are gated */ |
| ctrl |= 1; |
| __raw_writel(ctrl, reg); |
| } |
| } |
| _reset_gpio(bank, bank->chip.base + offset); |
| spin_unlock_irqrestore(&bank->lock, flags); |
| } |
| |
| /* |
| * We need to unmask the GPIO bank interrupt as soon as possible to |
| * avoid missing GPIO interrupts for other lines in the bank. |
| * Then we need to mask-read-clear-unmask the triggered GPIO lines |
| * in the bank to avoid missing nested interrupts for a GPIO line. |
| * If we wait to unmask individual GPIO lines in the bank after the |
| * line's interrupt handler has been run, we may miss some nested |
| * interrupts. |
| */ |
| static void gpio_irq_handler(unsigned int irq, struct irq_desc *desc) |
| { |
| void __iomem *isr_reg = NULL; |
| u32 isr; |
| unsigned int gpio_irq, gpio_index; |
| struct gpio_bank *bank; |
| u32 retrigger = 0; |
| int unmasked = 0; |
| |
| desc->chip->ack(irq); |
| |
| bank = get_irq_data(irq); |
| #ifdef CONFIG_ARCH_OMAP1 |
| if (bank->method == METHOD_MPUIO) |
| isr_reg = bank->base + OMAP_MPUIO_GPIO_INT; |
| #endif |
| #ifdef CONFIG_ARCH_OMAP15XX |
| if (bank->method == METHOD_GPIO_1510) |
| isr_reg = bank->base + OMAP1510_GPIO_INT_STATUS; |
| #endif |
| #if defined(CONFIG_ARCH_OMAP16XX) |
| if (bank->method == METHOD_GPIO_1610) |
| isr_reg = bank->base + OMAP1610_GPIO_IRQSTATUS1; |
| #endif |
| #if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850) |
| if (bank->method == METHOD_GPIO_7XX) |
| isr_reg = bank->base + OMAP7XX_GPIO_INT_STATUS; |
| #endif |
| #if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) |
| if (bank->method == METHOD_GPIO_24XX) |
| isr_reg = bank->base + OMAP24XX_GPIO_IRQSTATUS1; |
| #endif |
| #if defined(CONFIG_ARCH_OMAP4) |
| if (bank->method == METHOD_GPIO_44XX) |
| isr_reg = bank->base + OMAP4_GPIO_IRQSTATUS0; |
| #endif |
| while(1) { |
| u32 isr_saved, level_mask = 0; |
| u32 enabled; |
| |
| enabled = _get_gpio_irqbank_mask(bank); |
| isr_saved = isr = __raw_readl(isr_reg) & enabled; |
| |
| if (cpu_is_omap15xx() && (bank->method == METHOD_MPUIO)) |
| isr &= 0x0000ffff; |
| |
| if (cpu_class_is_omap2()) { |
| level_mask = bank->level_mask & enabled; |
| } |
| |
| /* clear edge sensitive interrupts before handler(s) are |
| called so that we don't miss any interrupt occurred while |
| executing them */ |
| _enable_gpio_irqbank(bank, isr_saved & ~level_mask, 0); |
| _clear_gpio_irqbank(bank, isr_saved & ~level_mask); |
| _enable_gpio_irqbank(bank, isr_saved & ~level_mask, 1); |
| |
| /* if there is only edge sensitive GPIO pin interrupts |
| configured, we could unmask GPIO bank interrupt immediately */ |
| if (!level_mask && !unmasked) { |
| unmasked = 1; |
| desc->chip->unmask(irq); |
| } |
| |
| isr |= retrigger; |
| retrigger = 0; |
| if (!isr) |
| break; |
| |
| gpio_irq = bank->virtual_irq_start; |
| for (; isr != 0; isr >>= 1, gpio_irq++) { |
| gpio_index = get_gpio_index(irq_to_gpio(gpio_irq)); |
| |
| if (!(isr & 1)) |
| continue; |
| |
| #ifdef CONFIG_ARCH_OMAP1 |
| /* |
| * Some chips can't respond to both rising and falling |
| * at the same time. If this irq was requested with |
| * both flags, we need to flip the ICR data for the IRQ |
| * to respond to the IRQ for the opposite direction. |
| * This will be indicated in the bank toggle_mask. |
| */ |
| if (bank->toggle_mask & (1 << gpio_index)) |
| _toggle_gpio_edge_triggering(bank, gpio_index); |
| #endif |
| |
| generic_handle_irq(gpio_irq); |
| } |
| } |
| /* if bank has any level sensitive GPIO pin interrupt |
| configured, we must unmask the bank interrupt only after |
| handler(s) are executed in order to avoid spurious bank |
| interrupt */ |
| if (!unmasked) |
| desc->chip->unmask(irq); |
| |
| } |
| |
| static void gpio_irq_shutdown(unsigned int irq) |
| { |
| unsigned int gpio = irq - IH_GPIO_BASE; |
| struct gpio_bank *bank = get_irq_chip_data(irq); |
| |
| _reset_gpio(bank, gpio); |
| } |
| |
| static void gpio_ack_irq(unsigned int irq) |
| { |
| unsigned int gpio = irq - IH_GPIO_BASE; |
| struct gpio_bank *bank = get_irq_chip_data(irq); |
| |
| _clear_gpio_irqstatus(bank, gpio); |
| } |
| |
| static void gpio_mask_irq(unsigned int irq) |
| { |
| unsigned int gpio = irq - IH_GPIO_BASE; |
| struct gpio_bank *bank = get_irq_chip_data(irq); |
| |
| _set_gpio_irqenable(bank, gpio, 0); |
| _set_gpio_triggering(bank, get_gpio_index(gpio), IRQ_TYPE_NONE); |
| } |
| |
| static void gpio_unmask_irq(unsigned int irq) |
| { |
| unsigned int gpio = irq - IH_GPIO_BASE; |
| struct gpio_bank *bank = get_irq_chip_data(irq); |
| unsigned int irq_mask = 1 << get_gpio_index(gpio); |
| struct irq_desc *desc = irq_to_desc(irq); |
| u32 trigger = desc->status & IRQ_TYPE_SENSE_MASK; |
| |
| if (trigger) |
| _set_gpio_triggering(bank, get_gpio_index(gpio), trigger); |
| |
| /* For level-triggered GPIOs, the clearing must be done after |
| * the HW source is cleared, thus after the handler has run */ |
| if (bank->level_mask & irq_mask) { |
| _set_gpio_irqenable(bank, gpio, 0); |
| _clear_gpio_irqstatus(bank, gpio); |
| } |
| |
| _set_gpio_irqenable(bank, gpio, 1); |
| } |
| |
| static struct irq_chip gpio_irq_chip = { |
| .name = "GPIO", |
| .shutdown = gpio_irq_shutdown, |
| .ack = gpio_ack_irq, |
| .mask = gpio_mask_irq, |
| .unmask = gpio_unmask_irq, |
| .set_type = gpio_irq_type, |
| .set_wake = gpio_wake_enable, |
| }; |
| |
| /*---------------------------------------------------------------------*/ |
| |
| #ifdef CONFIG_ARCH_OMAP1 |
| |
| /* MPUIO uses the always-on 32k clock */ |
| |
| static void mpuio_ack_irq(unsigned int irq) |
| { |
| /* The ISR is reset automatically, so do nothing here. */ |
| } |
| |
| static void mpuio_mask_irq(unsigned int irq) |
| { |
| unsigned int gpio = OMAP_MPUIO(irq - IH_MPUIO_BASE); |
| struct gpio_bank *bank = get_irq_chip_data(irq); |
| |
| _set_gpio_irqenable(bank, gpio, 0); |
| } |
| |
| static void mpuio_unmask_irq(unsigned int irq) |
| { |
| unsigned int gpio = OMAP_MPUIO(irq - IH_MPUIO_BASE); |
| struct gpio_bank *bank = get_irq_chip_data(irq); |
| |
| _set_gpio_irqenable(bank, gpio, 1); |
| } |
| |
| static struct irq_chip mpuio_irq_chip = { |
| .name = "MPUIO", |
| .ack = mpuio_ack_irq, |
| .mask = mpuio_mask_irq, |
| .unmask = mpuio_unmask_irq, |
| .set_type = gpio_irq_type, |
| #ifdef CONFIG_ARCH_OMAP16XX |
| /* REVISIT: assuming only 16xx supports MPUIO wake events */ |
| .set_wake = gpio_wake_enable, |
| #endif |
| }; |
| |
| |
| #define bank_is_mpuio(bank) ((bank)->method == METHOD_MPUIO) |
| |
| |
| #ifdef CONFIG_ARCH_OMAP16XX |
| |
| #include <linux/platform_device.h> |
| |
| static int omap_mpuio_suspend_noirq(struct device *dev) |
| { |
| struct platform_device *pdev = to_platform_device(dev); |
| struct gpio_bank *bank = platform_get_drvdata(pdev); |
| void __iomem *mask_reg = bank->base + OMAP_MPUIO_GPIO_MASKIT; |
| unsigned long flags; |
| |
| spin_lock_irqsave(&bank->lock, flags); |
| bank->saved_wakeup = __raw_readl(mask_reg); |
| __raw_writel(0xffff & ~bank->suspend_wakeup, mask_reg); |
| spin_unlock_irqrestore(&bank->lock, flags); |
| |
| return 0; |
| } |
| |
| static int omap_mpuio_resume_noirq(struct device *dev) |
| { |
| struct platform_device *pdev = to_platform_device(dev); |
| struct gpio_bank *bank = platform_get_drvdata(pdev); |
| void __iomem *mask_reg = bank->base + OMAP_MPUIO_GPIO_MASKIT; |
| unsigned long flags; |
| |
| spin_lock_irqsave(&bank->lock, flags); |
| __raw_writel(bank->saved_wakeup, mask_reg); |
| spin_unlock_irqrestore(&bank->lock, flags); |
| |
| return 0; |
| } |
| |
| static const struct dev_pm_ops omap_mpuio_dev_pm_ops = { |
| .suspend_noirq = omap_mpuio_suspend_noirq, |
| .resume_noirq = omap_mpuio_resume_noirq, |
| }; |
| |
| /* use platform_driver for this, now that there's no longer any |
| * point to sys_device (other than not disturbing old code). |
| */ |
| static struct platform_driver omap_mpuio_driver = { |
| .driver = { |
| .name = "mpuio", |
| .pm = &omap_mpuio_dev_pm_ops, |
| }, |
| }; |
| |
| static struct platform_device omap_mpuio_device = { |
| .name = "mpuio", |
| .id = -1, |
| .dev = { |
| .driver = &omap_mpuio_driver.driver, |
| } |
| /* could list the /proc/iomem resources */ |
| }; |
| |
| static inline void mpuio_init(void) |
| { |
| platform_set_drvdata(&omap_mpuio_device, &gpio_bank_1610[0]); |
| |
| if (platform_driver_register(&omap_mpuio_driver) == 0) |
| (void) platform_device_register(&omap_mpuio_device); |
| } |
| |
| #else |
| static inline void mpuio_init(void) {} |
| #endif /* 16xx */ |
| |
| #else |
| |
| extern struct irq_chip mpuio_irq_chip; |
| |
| #define bank_is_mpuio(bank) 0 |
| static inline void mpuio_init(void) {} |
| |
| #endif |
| |
| /*---------------------------------------------------------------------*/ |
| |
| /* REVISIT these are stupid implementations! replace by ones that |
| * don't switch on METHOD_* and which mostly avoid spinlocks |
| */ |
| |
| static int gpio_input(struct gpio_chip *chip, unsigned offset) |
| { |
| struct gpio_bank *bank; |
| unsigned long flags; |
| |
| bank = container_of(chip, struct gpio_bank, chip); |
| spin_lock_irqsave(&bank->lock, flags); |
| _set_gpio_direction(bank, offset, 1); |
| spin_unlock_irqrestore(&bank->lock, flags); |
| return 0; |
| } |
| |
| static int gpio_is_input(struct gpio_bank *bank, int mask) |
| { |
| void __iomem *reg = bank->base; |
| |
| switch (bank->method) { |
| case METHOD_MPUIO: |
| reg += OMAP_MPUIO_IO_CNTL; |
| break; |
| case METHOD_GPIO_1510: |
| reg += OMAP1510_GPIO_DIR_CONTROL; |
| break; |
| case METHOD_GPIO_1610: |
| reg += OMAP1610_GPIO_DIRECTION; |
| break; |
| case METHOD_GPIO_7XX: |
| reg += OMAP7XX_GPIO_DIR_CONTROL; |
| break; |
| case METHOD_GPIO_24XX: |
| reg += OMAP24XX_GPIO_OE; |
| break; |
| case METHOD_GPIO_44XX: |
| reg += OMAP4_GPIO_OE; |
| break; |
| default: |
| WARN_ONCE(1, "gpio_is_input: incorrect OMAP GPIO method"); |
| return -EINVAL; |
| } |
| return __raw_readl(reg) & mask; |
| } |
| |
| static int gpio_get(struct gpio_chip *chip, unsigned offset) |
| { |
| struct gpio_bank *bank; |
| void __iomem *reg; |
| int gpio; |
| u32 mask; |
| |
| gpio = chip->base + offset; |
| bank = get_gpio_bank(gpio); |
| reg = bank->base; |
| mask = 1 << get_gpio_index(gpio); |
| |
| if (gpio_is_input(bank, mask)) |
| return _get_gpio_datain(bank, gpio); |
| else |
| return _get_gpio_dataout(bank, gpio); |
| } |
| |
| static int gpio_output(struct gpio_chip *chip, unsigned offset, int value) |
| { |
| struct gpio_bank *bank; |
| unsigned long flags; |
| |
| bank = container_of(chip, struct gpio_bank, chip); |
| spin_lock_irqsave(&bank->lock, flags); |
| _set_gpio_dataout(bank, offset, value); |
| _set_gpio_direction(bank, offset, 0); |
| spin_unlock_irqrestore(&bank->lock, flags); |
| return 0; |
| } |
| |
| static int gpio_debounce(struct gpio_chip *chip, unsigned offset, |
| unsigned debounce) |
| { |
| struct gpio_bank *bank; |
| unsigned long flags; |
| |
| bank = container_of(chip, struct gpio_bank, chip); |
| spin_lock_irqsave(&bank->lock, flags); |
| _set_gpio_debounce(bank, offset, debounce); |
| spin_unlock_irqrestore(&bank->lock, flags); |
| |
| return 0; |
| } |
| |
| static void gpio_set(struct gpio_chip *chip, unsigned offset, int value) |
| { |
| struct gpio_bank *bank; |
| unsigned long flags; |
| |
| bank = container_of(chip, struct gpio_bank, chip); |
| spin_lock_irqsave(&bank->lock, flags); |
| _set_gpio_dataout(bank, offset, value); |
| spin_unlock_irqrestore(&bank->lock, flags); |
| } |
| |
| static int gpio_2irq(struct gpio_chip *chip, unsigned offset) |
| { |
| struct gpio_bank *bank; |
| |
| bank = container_of(chip, struct gpio_bank, chip); |
| return bank->virtual_irq_start + offset; |
| } |
| |
| /*---------------------------------------------------------------------*/ |
| |
| static int initialized; |
| #if defined(CONFIG_ARCH_OMAP1) || defined(CONFIG_ARCH_OMAP2) |
| static struct clk * gpio_ick; |
| #endif |
| |
| #if defined(CONFIG_ARCH_OMAP2) |
| static struct clk * gpio_fck; |
| #endif |
| |
| #if defined(CONFIG_ARCH_OMAP2430) |
| static struct clk * gpio5_ick; |
| static struct clk * gpio5_fck; |
| #endif |
| |
| #if defined(CONFIG_ARCH_OMAP3) || defined(CONFIG_ARCH_OMAP4) |
| static struct clk *gpio_iclks[OMAP34XX_NR_GPIOS]; |
| #endif |
| |
| static void __init omap_gpio_show_rev(void) |
| { |
| u32 rev; |
| |
| if (cpu_is_omap16xx()) |
| rev = __raw_readw(gpio_bank[1].base + OMAP1610_GPIO_REVISION); |
| else if (cpu_is_omap24xx() || cpu_is_omap34xx()) |
| rev = __raw_readl(gpio_bank[0].base + OMAP24XX_GPIO_REVISION); |
| else if (cpu_is_omap44xx()) |
| rev = __raw_readl(gpio_bank[0].base + OMAP4_GPIO_REVISION); |
| else |
| return; |
| |
| printk(KERN_INFO "OMAP GPIO hardware version %d.%d\n", |
| (rev >> 4) & 0x0f, rev & 0x0f); |
| } |
| |
| /* This lock class tells lockdep that GPIO irqs are in a different |
| * category than their parents, so it won't report false recursion. |
| */ |
| static struct lock_class_key gpio_lock_class; |
| |
| static int __init _omap_gpio_init(void) |
| { |
| int i; |
| int gpio = 0; |
| struct gpio_bank *bank; |
| int bank_size = SZ_8K; /* Module 4KB + L4 4KB except on omap1 */ |
| char clk_name[11]; |
| |
| initialized = 1; |
| |
| #if defined(CONFIG_ARCH_OMAP1) |
| if (cpu_is_omap15xx()) { |
| gpio_ick = clk_get(NULL, "arm_gpio_ck"); |
| if (IS_ERR(gpio_ick)) |
| printk("Could not get arm_gpio_ck\n"); |
| else |
| clk_enable(gpio_ick); |
| } |
| #endif |
| #if defined(CONFIG_ARCH_OMAP2) |
| if (cpu_class_is_omap2()) { |
| gpio_ick = clk_get(NULL, "gpios_ick"); |
| if (IS_ERR(gpio_ick)) |
| printk("Could not get gpios_ick\n"); |
| else |
| clk_enable(gpio_ick); |
| gpio_fck = clk_get(NULL, "gpios_fck"); |
| if (IS_ERR(gpio_fck)) |
| printk("Could not get gpios_fck\n"); |
| else |
| clk_enable(gpio_fck); |
| |
| /* |
| * On 2430 & 3430 GPIO 5 uses CORE L4 ICLK |
| */ |
| #if defined(CONFIG_ARCH_OMAP2430) |
| if (cpu_is_omap2430()) { |
| gpio5_ick = clk_get(NULL, "gpio5_ick"); |
| if (IS_ERR(gpio5_ick)) |
| printk("Could not get gpio5_ick\n"); |
| else |
| clk_enable(gpio5_ick); |
| gpio5_fck = clk_get(NULL, "gpio5_fck"); |
| if (IS_ERR(gpio5_fck)) |
| printk("Could not get gpio5_fck\n"); |
| else |
| clk_enable(gpio5_fck); |
| } |
| #endif |
| } |
| #endif |
| |
| #if defined(CONFIG_ARCH_OMAP3) || defined(CONFIG_ARCH_OMAP4) |
| if (cpu_is_omap34xx() || cpu_is_omap44xx()) { |
| for (i = 0; i < OMAP34XX_NR_GPIOS; i++) { |
| sprintf(clk_name, "gpio%d_ick", i + 1); |
| gpio_iclks[i] = clk_get(NULL, clk_name); |
| if (IS_ERR(gpio_iclks[i])) |
| printk(KERN_ERR "Could not get %s\n", clk_name); |
| else |
| clk_enable(gpio_iclks[i]); |
| } |
| } |
| #endif |
| |
| |
| #ifdef CONFIG_ARCH_OMAP15XX |
| if (cpu_is_omap15xx()) { |
| gpio_bank_count = 2; |
| gpio_bank = gpio_bank_1510; |
| bank_size = SZ_2K; |
| } |
| #endif |
| #if defined(CONFIG_ARCH_OMAP16XX) |
| if (cpu_is_omap16xx()) { |
| gpio_bank_count = 5; |
| gpio_bank = gpio_bank_1610; |
| bank_size = SZ_2K; |
| } |
| #endif |
| #if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850) |
| if (cpu_is_omap7xx()) { |
| gpio_bank_count = 7; |
| gpio_bank = gpio_bank_7xx; |
| bank_size = SZ_2K; |
| } |
| #endif |
| #ifdef CONFIG_ARCH_OMAP2 |
| if (cpu_is_omap242x()) { |
| gpio_bank_count = 4; |
| gpio_bank = gpio_bank_242x; |
| } |
| if (cpu_is_omap243x()) { |
| gpio_bank_count = 5; |
| gpio_bank = gpio_bank_243x; |
| } |
| #endif |
| #ifdef CONFIG_ARCH_OMAP3 |
| if (cpu_is_omap34xx()) { |
| gpio_bank_count = OMAP34XX_NR_GPIOS; |
| gpio_bank = gpio_bank_34xx; |
| } |
| #endif |
| #ifdef CONFIG_ARCH_OMAP4 |
| if (cpu_is_omap44xx()) { |
| gpio_bank_count = OMAP34XX_NR_GPIOS; |
| gpio_bank = gpio_bank_44xx; |
| } |
| #endif |
| for (i = 0; i < gpio_bank_count; i++) { |
| int j, gpio_count = 16; |
| |
| bank = &gpio_bank[i]; |
| spin_lock_init(&bank->lock); |
| |
| /* Static mapping, never released */ |
| bank->base = ioremap(bank->pbase, bank_size); |
| if (!bank->base) { |
| printk(KERN_ERR "Could not ioremap gpio bank%i\n", i); |
| continue; |
| } |
| |
| if (bank_is_mpuio(bank)) |
| __raw_writew(0xffff, bank->base + OMAP_MPUIO_GPIO_MASKIT); |
| if (cpu_is_omap15xx() && bank->method == METHOD_GPIO_1510) { |
| __raw_writew(0xffff, bank->base + OMAP1510_GPIO_INT_MASK); |
| __raw_writew(0x0000, bank->base + OMAP1510_GPIO_INT_STATUS); |
| } |
| if (cpu_is_omap16xx() && bank->method == METHOD_GPIO_1610) { |
| __raw_writew(0x0000, bank->base + OMAP1610_GPIO_IRQENABLE1); |
| __raw_writew(0xffff, bank->base + OMAP1610_GPIO_IRQSTATUS1); |
| __raw_writew(0x0014, bank->base + OMAP1610_GPIO_SYSCONFIG); |
| } |
| if (cpu_is_omap7xx() && bank->method == METHOD_GPIO_7XX) { |
| __raw_writel(0xffffffff, bank->base + OMAP7XX_GPIO_INT_MASK); |
| __raw_writel(0x00000000, bank->base + OMAP7XX_GPIO_INT_STATUS); |
| |
| gpio_count = 32; /* 7xx has 32-bit GPIOs */ |
| } |
| |
| #ifdef CONFIG_ARCH_OMAP2PLUS |
| if ((bank->method == METHOD_GPIO_24XX) || |
| (bank->method == METHOD_GPIO_44XX)) { |
| static const u32 non_wakeup_gpios[] = { |
| 0xe203ffc0, 0x08700040 |
| }; |
| |
| if (cpu_is_omap44xx()) { |
| __raw_writel(0xffffffff, bank->base + |
| OMAP4_GPIO_IRQSTATUSCLR0); |
| __raw_writew(0x0015, bank->base + |
| OMAP4_GPIO_SYSCONFIG); |
| __raw_writel(0x00000000, bank->base + |
| OMAP4_GPIO_DEBOUNCENABLE); |
| /* |
| * Initialize interface clock ungated, |
| * module enabled |
| */ |
| __raw_writel(0, bank->base + OMAP4_GPIO_CTRL); |
| } else { |
| __raw_writel(0x00000000, bank->base + |
| OMAP24XX_GPIO_IRQENABLE1); |
| __raw_writel(0xffffffff, bank->base + |
| OMAP24XX_GPIO_IRQSTATUS1); |
| __raw_writew(0x0015, bank->base + |
| OMAP24XX_GPIO_SYSCONFIG); |
| __raw_writel(0x00000000, bank->base + |
| OMAP24XX_GPIO_DEBOUNCE_EN); |
| |
| /* |
| * Initialize interface clock ungated, |
| * module enabled |
| */ |
| __raw_writel(0, bank->base + |
| OMAP24XX_GPIO_CTRL); |
| } |
| if (cpu_is_omap24xx() && |
| i < ARRAY_SIZE(non_wakeup_gpios)) |
| bank->non_wakeup_gpios = non_wakeup_gpios[i]; |
| gpio_count = 32; |
| } |
| #endif |
| |
| bank->mod_usage = 0; |
| /* REVISIT eventually switch from OMAP-specific gpio structs |
| * over to the generic ones |
| */ |
| bank->chip.request = omap_gpio_request; |
| bank->chip.free = omap_gpio_free; |
| bank->chip.direction_input = gpio_input; |
| bank->chip.get = gpio_get; |
| bank->chip.direction_output = gpio_output; |
| bank->chip.set_debounce = gpio_debounce; |
| bank->chip.set = gpio_set; |
| bank->chip.to_irq = gpio_2irq; |
| if (bank_is_mpuio(bank)) { |
| bank->chip.label = "mpuio"; |
| #ifdef CONFIG_ARCH_OMAP16XX |
| bank->chip.dev = &omap_mpuio_device.dev; |
| #endif |
| bank->chip.base = OMAP_MPUIO(0); |
| } else { |
| bank->chip.label = "gpio"; |
| bank->chip.base = gpio; |
| gpio += gpio_count; |
| } |
| bank->chip.ngpio = gpio_count; |
| |
| gpiochip_add(&bank->chip); |
| |
| for (j = bank->virtual_irq_start; |
| j < bank->virtual_irq_start + gpio_count; j++) { |
| lockdep_set_class(&irq_desc[j].lock, &gpio_lock_class); |
| set_irq_chip_data(j, bank); |
| if (bank_is_mpuio(bank)) |
| set_irq_chip(j, &mpuio_irq_chip); |
| else |
| set_irq_chip(j, &gpio_irq_chip); |
| set_irq_handler(j, handle_simple_irq); |
| set_irq_flags(j, IRQF_VALID); |
| } |
| set_irq_chained_handler(bank->irq, gpio_irq_handler); |
| set_irq_data(bank->irq, bank); |
| |
| if (cpu_is_omap34xx() || cpu_is_omap44xx()) { |
| sprintf(clk_name, "gpio%d_dbck", i + 1); |
| bank->dbck = clk_get(NULL, clk_name); |
| if (IS_ERR(bank->dbck)) |
| printk(KERN_ERR "Could not get %s\n", clk_name); |
| } |
| } |
| |
| /* Enable system clock for GPIO module. |
| * The CAM_CLK_CTRL *is* really the right place. */ |
| if (cpu_is_omap16xx()) |
| omap_writel(omap_readl(ULPD_CAM_CLK_CTRL) | 0x04, ULPD_CAM_CLK_CTRL); |
| |
| /* Enable autoidle for the OCP interface */ |
| if (cpu_is_omap24xx()) |
| omap_writel(1 << 0, 0x48019010); |
| if (cpu_is_omap34xx()) |
| omap_writel(1 << 0, 0x48306814); |
| |
| omap_gpio_show_rev(); |
| |
| return 0; |
| } |
| |
| #if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP2PLUS) |
| static int omap_gpio_suspend(struct sys_device *dev, pm_message_t mesg) |
| { |
| int i; |
| |
| if (!cpu_class_is_omap2() && !cpu_is_omap16xx()) |
| return 0; |
| |
| for (i = 0; i < gpio_bank_count; i++) { |
| struct gpio_bank *bank = &gpio_bank[i]; |
| void __iomem *wake_status; |
| void __iomem *wake_clear; |
| void __iomem *wake_set; |
| unsigned long flags; |
| |
| switch (bank->method) { |
| #ifdef CONFIG_ARCH_OMAP16XX |
| case METHOD_GPIO_1610: |
| wake_status = bank->base + OMAP1610_GPIO_WAKEUPENABLE; |
| wake_clear = bank->base + OMAP1610_GPIO_CLEAR_WAKEUPENA; |
| wake_set = bank->base + OMAP1610_GPIO_SET_WAKEUPENA; |
| break; |
| #endif |
| #if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) |
| case METHOD_GPIO_24XX: |
| wake_status = bank->base + OMAP24XX_GPIO_WAKE_EN; |
| wake_clear = bank->base + OMAP24XX_GPIO_CLEARWKUENA; |
| wake_set = bank->base + OMAP24XX_GPIO_SETWKUENA; |
| break; |
| #endif |
| #ifdef CONFIG_ARCH_OMAP4 |
| case METHOD_GPIO_44XX: |
| wake_status = bank->base + OMAP4_GPIO_IRQWAKEN0; |
| wake_clear = bank->base + OMAP4_GPIO_IRQWAKEN0; |
| wake_set = bank->base + OMAP4_GPIO_IRQWAKEN0; |
| break; |
| #endif |
| default: |
| continue; |
| } |
| |
| spin_lock_irqsave(&bank->lock, flags); |
| bank->saved_wakeup = __raw_readl(wake_status); |
| __raw_writel(0xffffffff, wake_clear); |
| __raw_writel(bank->suspend_wakeup, wake_set); |
| spin_unlock_irqrestore(&bank->lock, flags); |
| } |
| |
| return 0; |
| } |
| |
| static int omap_gpio_resume(struct sys_device *dev) |
| { |
| int i; |
| |
| if (!cpu_class_is_omap2() && !cpu_is_omap16xx()) |
| return 0; |
| |
| for (i = 0; i < gpio_bank_count; i++) { |
| struct gpio_bank *bank = &gpio_bank[i]; |
| void __iomem *wake_clear; |
| void __iomem *wake_set; |
| unsigned long flags; |
| |
| switch (bank->method) { |
| #ifdef CONFIG_ARCH_OMAP16XX |
| case METHOD_GPIO_1610: |
| wake_clear = bank->base + OMAP1610_GPIO_CLEAR_WAKEUPENA; |
| wake_set = bank->base + OMAP1610_GPIO_SET_WAKEUPENA; |
| break; |
| #endif |
| #if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) |
| case METHOD_GPIO_24XX: |
| wake_clear = bank->base + OMAP24XX_GPIO_CLEARWKUENA; |
| wake_set = bank->base + OMAP24XX_GPIO_SETWKUENA; |
| break; |
| #endif |
| #ifdef CONFIG_ARCH_OMAP4 |
| case METHOD_GPIO_44XX: |
| wake_clear = bank->base + OMAP4_GPIO_IRQWAKEN0; |
| wake_set = bank->base + OMAP4_GPIO_IRQWAKEN0; |
| break; |
| #endif |
| default: |
| continue; |
| } |
| |
| spin_lock_irqsave(&bank->lock, flags); |
| __raw_writel(0xffffffff, wake_clear); |
| __raw_writel(bank->saved_wakeup, wake_set); |
| spin_unlock_irqrestore(&bank->lock, flags); |
| } |
| |
| return 0; |
| } |
| |
| static struct sysdev_class omap_gpio_sysclass = { |
| .name = "gpio", |
| .suspend = omap_gpio_suspend, |
| .resume = omap_gpio_resume, |
| }; |
| |
| static struct sys_device omap_gpio_device = { |
| .id = 0, |
| .cls = &omap_gpio_sysclass, |
| }; |
| |
| #endif |
| |
| #ifdef CONFIG_ARCH_OMAP2PLUS |
| |
| static int workaround_enabled; |
| |
| void omap2_gpio_prepare_for_idle(int power_state) |
| { |
| int i, c = 0; |
| int min = 0; |
| |
| if (cpu_is_omap34xx()) |
| min = 1; |
| |
| for (i = min; i < gpio_bank_count; i++) { |
| struct gpio_bank *bank = &gpio_bank[i]; |
| u32 l1, l2; |
| |
| if (bank->dbck_enable_mask) |
| clk_disable(bank->dbck); |
| |
| if (power_state > PWRDM_POWER_OFF) |
| continue; |
| |
| /* If going to OFF, remove triggering for all |
| * non-wakeup GPIOs. Otherwise spurious IRQs will be |
| * generated. See OMAP2420 Errata item 1.101. */ |
| if (!(bank->enabled_non_wakeup_gpios)) |
| continue; |
| |
| if (cpu_is_omap24xx() || cpu_is_omap34xx()) { |
| bank->saved_datain = __raw_readl(bank->base + |
| OMAP24XX_GPIO_DATAIN); |
| l1 = __raw_readl(bank->base + |
| OMAP24XX_GPIO_FALLINGDETECT); |
| l2 = __raw_readl(bank->base + |
| OMAP24XX_GPIO_RISINGDETECT); |
| } |
| |
| if (cpu_is_omap44xx()) { |
| bank->saved_datain = __raw_readl(bank->base + |
| OMAP4_GPIO_DATAIN); |
| l1 = __raw_readl(bank->base + |
| OMAP4_GPIO_FALLINGDETECT); |
| l2 = __raw_readl(bank->base + |
| OMAP4_GPIO_RISINGDETECT); |
| } |
| |
| bank->saved_fallingdetect = l1; |
| bank->saved_risingdetect = l2; |
| l1 &= ~bank->enabled_non_wakeup_gpios; |
| l2 &= ~bank->enabled_non_wakeup_gpios; |
| |
| if (cpu_is_omap24xx() || cpu_is_omap34xx()) { |
| __raw_writel(l1, bank->base + |
| OMAP24XX_GPIO_FALLINGDETECT); |
| __raw_writel(l2, bank->base + |
| OMAP24XX_GPIO_RISINGDETECT); |
| } |
| |
| if (cpu_is_omap44xx()) { |
| __raw_writel(l1, bank->base + OMAP4_GPIO_FALLINGDETECT); |
| __raw_writel(l2, bank->base + OMAP4_GPIO_RISINGDETECT); |
| } |
| |
| c++; |
| } |
| if (!c) { |
| workaround_enabled = 0; |
| return; |
| } |
| workaround_enabled = 1; |
| } |
| |
| void omap2_gpio_resume_after_idle(void) |
| { |
| int i; |
| int min = 0; |
| |
| if (cpu_is_omap34xx()) |
| min = 1; |
| for (i = min; i < gpio_bank_count; i++) { |
| struct gpio_bank *bank = &gpio_bank[i]; |
| u32 l, gen, gen0, gen1; |
| |
| if (bank->dbck_enable_mask) |
| clk_enable(bank->dbck); |
| |
| if (!workaround_enabled) |
| continue; |
| |
| if (!(bank->enabled_non_wakeup_gpios)) |
| continue; |
| |
| if (cpu_is_omap24xx() || cpu_is_omap34xx()) { |
| __raw_writel(bank->saved_fallingdetect, |
| bank->base + OMAP24XX_GPIO_FALLINGDETECT); |
| __raw_writel(bank->saved_risingdetect, |
| bank->base + OMAP24XX_GPIO_RISINGDETECT); |
| l = __raw_readl(bank->base + OMAP24XX_GPIO_DATAIN); |
| } |
| |
| if (cpu_is_omap44xx()) { |
| __raw_writel(bank->saved_fallingdetect, |
| bank->base + OMAP4_GPIO_FALLINGDETECT); |
| __raw_writel(bank->saved_risingdetect, |
| bank->base + OMAP4_GPIO_RISINGDETECT); |
| l = __raw_readl(bank->base + OMAP4_GPIO_DATAIN); |
| } |
| |
| /* Check if any of the non-wakeup interrupt GPIOs have changed |
| * state. If so, generate an IRQ by software. This is |
| * horribly racy, but it's the best we can do to work around |
| * this silicon bug. */ |
| l ^= bank->saved_datain; |
| l &= bank->enabled_non_wakeup_gpios; |
| |
| /* |
| * No need to generate IRQs for the rising edge for gpio IRQs |
| * configured with falling edge only; and vice versa. |
| */ |
| gen0 = l & bank->saved_fallingdetect; |
| gen0 &= bank->saved_datain; |
| |
| gen1 = l & bank->saved_risingdetect; |
| gen1 &= ~(bank->saved_datain); |
| |
| /* FIXME: Consider GPIO IRQs with level detections properly! */ |
| gen = l & (~(bank->saved_fallingdetect) & |
| ~(bank->saved_risingdetect)); |
| /* Consider all GPIO IRQs needed to be updated */ |
| gen |= gen0 | gen1; |
| |
| if (gen) { |
| u32 old0, old1; |
| |
| if (cpu_is_omap24xx() || cpu_is_omap34xx()) { |
| old0 = __raw_readl(bank->base + |
| OMAP24XX_GPIO_LEVELDETECT0); |
| old1 = __raw_readl(bank->base + |
| OMAP24XX_GPIO_LEVELDETECT1); |
| __raw_writel(old0 | gen, bank->base + |
| OMAP24XX_GPIO_LEVELDETECT0); |
| __raw_writel(old1 | gen, bank->base + |
| OMAP24XX_GPIO_LEVELDETECT1); |
| __raw_writel(old0, bank->base + |
| OMAP24XX_GPIO_LEVELDETECT0); |
| __raw_writel(old1, bank->base + |
| OMAP24XX_GPIO_LEVELDETECT1); |
| } |
| |
| if (cpu_is_omap44xx()) { |
| old0 = __raw_readl(bank->base + |
| OMAP4_GPIO_LEVELDETECT0); |
| old1 = __raw_readl(bank->base + |
| OMAP4_GPIO_LEVELDETECT1); |
| __raw_writel(old0 | l, bank->base + |
| OMAP4_GPIO_LEVELDETECT0); |
| __raw_writel(old1 | l, bank->base + |
| OMAP4_GPIO_LEVELDETECT1); |
| __raw_writel(old0, bank->base + |
| OMAP4_GPIO_LEVELDETECT0); |
| __raw_writel(old1, bank->base + |
| OMAP4_GPIO_LEVELDETECT1); |
| } |
| } |
| } |
| |
| } |
| |
| #endif |
| |
| #ifdef CONFIG_ARCH_OMAP3 |
| /* save the registers of bank 2-6 */ |
| void omap_gpio_save_context(void) |
| { |
| int i; |
| |
| /* saving banks from 2-6 only since GPIO1 is in WKUP */ |
| for (i = 1; i < gpio_bank_count; i++) { |
| struct gpio_bank *bank = &gpio_bank[i]; |
| gpio_context[i].sysconfig = |
| __raw_readl(bank->base + OMAP24XX_GPIO_SYSCONFIG); |
| gpio_context[i].irqenable1 = |
| __raw_readl(bank->base + OMAP24XX_GPIO_IRQENABLE1); |
| gpio_context[i].irqenable2 = |
| __raw_readl(bank->base + OMAP24XX_GPIO_IRQENABLE2); |
| gpio_context[i].wake_en = |
| __raw_readl(bank->base + OMAP24XX_GPIO_WAKE_EN); |
| gpio_context[i].ctrl = |
| __raw_readl(bank->base + OMAP24XX_GPIO_CTRL); |
| gpio_context[i].oe = |
| __raw_readl(bank->base + OMAP24XX_GPIO_OE); |
| gpio_context[i].leveldetect0 = |
| __raw_readl(bank->base + OMAP24XX_GPIO_LEVELDETECT0); |
| gpio_context[i].leveldetect1 = |
| __raw_readl(bank->base + OMAP24XX_GPIO_LEVELDETECT1); |
| gpio_context[i].risingdetect = |
| __raw_readl(bank->base + OMAP24XX_GPIO_RISINGDETECT); |
| gpio_context[i].fallingdetect = |
| __raw_readl(bank->base + OMAP24XX_GPIO_FALLINGDETECT); |
| gpio_context[i].dataout = |
| __raw_readl(bank->base + OMAP24XX_GPIO_DATAOUT); |
| } |
| } |
| |
| /* restore the required registers of bank 2-6 */ |
| void omap_gpio_restore_context(void) |
| { |
| int i; |
| |
| for (i = 1; i < gpio_bank_count; i++) { |
| struct gpio_bank *bank = &gpio_bank[i]; |
| __raw_writel(gpio_context[i].sysconfig, |
| bank->base + OMAP24XX_GPIO_SYSCONFIG); |
| __raw_writel(gpio_context[i].irqenable1, |
| bank->base + OMAP24XX_GPIO_IRQENABLE1); |
| __raw_writel(gpio_context[i].irqenable2, |
| bank->base + OMAP24XX_GPIO_IRQENABLE2); |
| __raw_writel(gpio_context[i].wake_en, |
| bank->base + OMAP24XX_GPIO_WAKE_EN); |
| __raw_writel(gpio_context[i].ctrl, |
| bank->base + OMAP24XX_GPIO_CTRL); |
| __raw_writel(gpio_context[i].oe, |
| bank->base + OMAP24XX_GPIO_OE); |
| __raw_writel(gpio_context[i].leveldetect0, |
| bank->base + OMAP24XX_GPIO_LEVELDETECT0); |
| __raw_writel(gpio_context[i].leveldetect1, |
| bank->base + OMAP24XX_GPIO_LEVELDETECT1); |
| __raw_writel(gpio_context[i].risingdetect, |
| bank->base + OMAP24XX_GPIO_RISINGDETECT); |
| __raw_writel(gpio_context[i].fallingdetect, |
| bank->base + OMAP24XX_GPIO_FALLINGDETECT); |
| __raw_writel(gpio_context[i].dataout, |
| bank->base + OMAP24XX_GPIO_DATAOUT); |
| } |
| } |
| #endif |
| |
| /* |
| * This may get called early from board specific init |
| * for boards that have interrupts routed via FPGA. |
| */ |
| int __init omap_gpio_init(void) |
| { |
| if (!initialized) |
| return _omap_gpio_init(); |
| else |
| return 0; |
| } |
| |
| static int __init omap_gpio_sysinit(void) |
| { |
| int ret = 0; |
| |
| if (!initialized) |
| ret = _omap_gpio_init(); |
| |
| mpuio_init(); |
| |
| #if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP2PLUS) |
| if (cpu_is_omap16xx() || cpu_class_is_omap2()) { |
| if (ret == 0) { |
| ret = sysdev_class_register(&omap_gpio_sysclass); |
| if (ret == 0) |
| ret = sysdev_register(&omap_gpio_device); |
| } |
| } |
| #endif |
| |
| return ret; |
| } |
| |
| arch_initcall(omap_gpio_sysinit); |