[media] staging: lirc: lirc_serial: use dynamic debugs
Replace custom debug macro dprintk() with pr_debug() or
dev_dbg(). Remove unused module param `debug`.
This removes the following checkpatch warning:
WARNING: Prefer [subsystem eg: netdev]_dbg([subsystem]dev, ... then dev_dbg(dev, ... then pr_debug(... to printk(KERN_DEBUG ...
+ printk(KERN_DEBUG LIRC_DRIVER_NAME ": " \
Signed-off-by: Maciek Borzecki <maciek.borzecki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
diff --git a/drivers/staging/media/lirc/lirc_serial.c b/drivers/staging/media/lirc/lirc_serial.c
index 465796a..64a7b2f 100644
--- a/drivers/staging/media/lirc/lirc_serial.c
+++ b/drivers/staging/media/lirc/lirc_serial.c
@@ -109,17 +109,9 @@
static int ioshift;
static bool softcarrier = true;
static bool share_irq;
-static bool debug;
static int sense = -1; /* -1 = auto, 0 = active high, 1 = active low */
static bool txsense; /* 0 = active high, 1 = active low */
-#define dprintk(fmt, args...) \
- do { \
- if (debug) \
- printk(KERN_DEBUG LIRC_DRIVER_NAME ": " \
- fmt, ## args); \
- } while (0)
-
/* forward declarations */
static long send_pulse_irdeo(unsigned long length);
static long send_pulse_homebrew(unsigned long length);
@@ -352,10 +344,9 @@
/* Derive pulse and space from the period */
pulse_width = period * duty_cycle / 100;
space_width = period - pulse_width;
- dprintk("in init_timing_params, freq=%d, duty_cycle=%d, "
- "clk/jiffy=%ld, pulse=%ld, space=%ld\n",
- freq, duty_cycle, __this_cpu_read(cpu_info.loops_per_jiffy),
- pulse_width, space_width);
+ pr_debug("in init_timing_params, freq=%d, duty_cycle=%d, clk/jiffy=%ld, pulse=%ld, space=%ld, conv_us_to_clocks=%ld\n",
+ freq, duty_cycle, __this_cpu_read(cpu_info.loops_per_jiffy),
+ pulse_width, space_width, conv_us_to_clocks);
return 0;
}
#else /* ! USE_RDTSC */
@@ -377,8 +368,8 @@
period = 256 * 1000000L / freq;
pulse_width = period * duty_cycle / 100;
space_width = period - pulse_width;
- dprintk("in init_timing_params, freq=%d pulse=%ld, space=%ld\n",
- freq, pulse_width, space_width);
+ pr_debug("in init_timing_params, freq=%d pulse=%ld, space=%ld\n",
+ freq, pulse_width, space_width);
return 0;
}
#endif /* USE_RDTSC */
@@ -500,7 +491,7 @@
{
if (lirc_buffer_full(&rbuf)) {
/* no new signals will be accepted */
- dprintk("Buffer overrun\n");
+ pr_debug("Buffer overrun\n");
return;
}
lirc_buffer_write(&rbuf, (void *)&l);
@@ -790,7 +781,7 @@
dev_info(&dev->dev, "Manually using active %s receiver\n",
sense ? "low" : "high");
- dprintk("Interrupt %d, port %04x obtained\n", irq, io);
+ dev_dbg(&dev->dev, "Interrupt %d, port %04x obtained\n", irq, io);
return 0;
}
@@ -895,7 +886,7 @@
return -ENOIOCTLCMD;
case LIRC_SET_SEND_DUTY_CYCLE:
- dprintk("SET_SEND_DUTY_CYCLE\n");
+ pr_debug("SET_SEND_DUTY_CYCLE\n");
if (!(hardware[type].features&LIRC_CAN_SET_SEND_DUTY_CYCLE))
return -ENOIOCTLCMD;
@@ -907,7 +898,7 @@
return init_timing_params(value, freq);
case LIRC_SET_SEND_CARRIER:
- dprintk("SET_SEND_CARRIER\n");
+ pr_debug("SET_SEND_CARRIER\n");
if (!(hardware[type].features&LIRC_CAN_SET_SEND_CARRIER))
return -ENOIOCTLCMD;
@@ -1102,7 +1093,7 @@
{
lirc_unregister_driver(driver.minor);
lirc_serial_exit();
- dprintk("cleaned up module\n");
+ pr_debug("cleaned up module\n");
}
@@ -1153,6 +1144,3 @@
module_param(softcarrier, bool, S_IRUGO);
MODULE_PARM_DESC(softcarrier, "Software carrier (0 = off, 1 = on, default on)");
-
-module_param(debug, bool, S_IRUGO | S_IWUSR);
-MODULE_PARM_DESC(debug, "Enable debugging messages");