| /* |
| * New driver for Marvell Yukon 2 chipset. |
| * Based on earlier sk98lin, and skge driver. |
| * |
| * This driver intentionally does not support all the features |
| * of the original driver such as link fail-over and link management because |
| * those should be done at higher levels. |
| * |
| * Copyright (C) 2005 Stephen Hemminger <shemminger@osdl.org> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. |
| */ |
| |
| #include <linux/crc32.h> |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/netdevice.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/etherdevice.h> |
| #include <linux/ethtool.h> |
| #include <linux/pci.h> |
| #include <linux/ip.h> |
| #include <net/ip.h> |
| #include <linux/tcp.h> |
| #include <linux/in.h> |
| #include <linux/delay.h> |
| #include <linux/workqueue.h> |
| #include <linux/if_vlan.h> |
| #include <linux/prefetch.h> |
| #include <linux/debugfs.h> |
| #include <linux/mii.h> |
| |
| #include <asm/irq.h> |
| |
| #if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE) |
| #define SKY2_VLAN_TAG_USED 1 |
| #endif |
| |
| #include "sky2.h" |
| |
| #define DRV_NAME "sky2" |
| #define DRV_VERSION "1.25" |
| #define PFX DRV_NAME " " |
| |
| /* |
| * The Yukon II chipset takes 64 bit command blocks (called list elements) |
| * that are organized into three (receive, transmit, status) different rings |
| * similar to Tigon3. |
| */ |
| |
| #define RX_LE_SIZE 1024 |
| #define RX_LE_BYTES (RX_LE_SIZE*sizeof(struct sky2_rx_le)) |
| #define RX_MAX_PENDING (RX_LE_SIZE/6 - 2) |
| #define RX_DEF_PENDING RX_MAX_PENDING |
| |
| /* This is the worst case number of transmit list elements for a single skb: |
| VLAN:GSO + CKSUM + Data + skb_frags * DMA */ |
| #define MAX_SKB_TX_LE (2 + (sizeof(dma_addr_t)/sizeof(u32))*(MAX_SKB_FRAGS+1)) |
| #define TX_MIN_PENDING (MAX_SKB_TX_LE+1) |
| #define TX_MAX_PENDING 4096 |
| #define TX_DEF_PENDING 127 |
| |
| #define STATUS_RING_SIZE 2048 /* 2 ports * (TX + 2*RX) */ |
| #define STATUS_LE_BYTES (STATUS_RING_SIZE*sizeof(struct sky2_status_le)) |
| #define TX_WATCHDOG (5 * HZ) |
| #define NAPI_WEIGHT 64 |
| #define PHY_RETRIES 1000 |
| |
| #define SKY2_EEPROM_MAGIC 0x9955aabb |
| |
| |
| #define RING_NEXT(x,s) (((x)+1) & ((s)-1)) |
| |
| static const u32 default_msg = |
| NETIF_MSG_DRV | NETIF_MSG_PROBE | NETIF_MSG_LINK |
| | NETIF_MSG_TIMER | NETIF_MSG_TX_ERR | NETIF_MSG_RX_ERR |
| | NETIF_MSG_IFUP | NETIF_MSG_IFDOWN; |
| |
| static int debug = -1; /* defaults above */ |
| module_param(debug, int, 0); |
| MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)"); |
| |
| static int copybreak __read_mostly = 128; |
| module_param(copybreak, int, 0); |
| MODULE_PARM_DESC(copybreak, "Receive copy threshold"); |
| |
| static int disable_msi = 0; |
| module_param(disable_msi, int, 0); |
| MODULE_PARM_DESC(disable_msi, "Disable Message Signaled Interrupt (MSI)"); |
| |
| static DEFINE_PCI_DEVICE_TABLE(sky2_id_table) = { |
| { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9000) }, /* SK-9Sxx */ |
| { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9E00) }, /* SK-9Exx */ |
| { PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4b00) }, /* DGE-560T */ |
| { PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4001) }, /* DGE-550SX */ |
| { PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4B02) }, /* DGE-560SX */ |
| { PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4B03) }, /* DGE-550T */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4340) }, /* 88E8021 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4341) }, /* 88E8022 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4342) }, /* 88E8061 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4343) }, /* 88E8062 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4344) }, /* 88E8021 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4345) }, /* 88E8022 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4346) }, /* 88E8061 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4347) }, /* 88E8062 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4350) }, /* 88E8035 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4351) }, /* 88E8036 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4352) }, /* 88E8038 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4353) }, /* 88E8039 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4354) }, /* 88E8040 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4355) }, /* 88E8040T */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4356) }, /* 88EC033 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4357) }, /* 88E8042 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x435A) }, /* 88E8048 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4360) }, /* 88E8052 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4361) }, /* 88E8050 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4362) }, /* 88E8053 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4363) }, /* 88E8055 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4364) }, /* 88E8056 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4365) }, /* 88E8070 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4366) }, /* 88EC036 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4367) }, /* 88EC032 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4368) }, /* 88EC034 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4369) }, /* 88EC042 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x436A) }, /* 88E8058 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x436B) }, /* 88E8071 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x436C) }, /* 88E8072 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x436D) }, /* 88E8055 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4370) }, /* 88E8075 */ |
| { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4380) }, /* 88E8057 */ |
| { 0 } |
| }; |
| |
| MODULE_DEVICE_TABLE(pci, sky2_id_table); |
| |
| /* Avoid conditionals by using array */ |
| static const unsigned txqaddr[] = { Q_XA1, Q_XA2 }; |
| static const unsigned rxqaddr[] = { Q_R1, Q_R2 }; |
| static const u32 portirq_msk[] = { Y2_IS_PORT_1, Y2_IS_PORT_2 }; |
| |
| static void sky2_set_multicast(struct net_device *dev); |
| |
| /* Access to PHY via serial interconnect */ |
| static int gm_phy_write(struct sky2_hw *hw, unsigned port, u16 reg, u16 val) |
| { |
| int i; |
| |
| gma_write16(hw, port, GM_SMI_DATA, val); |
| gma_write16(hw, port, GM_SMI_CTRL, |
| GM_SMI_CT_PHY_AD(PHY_ADDR_MARV) | GM_SMI_CT_REG_AD(reg)); |
| |
| for (i = 0; i < PHY_RETRIES; i++) { |
| u16 ctrl = gma_read16(hw, port, GM_SMI_CTRL); |
| if (ctrl == 0xffff) |
| goto io_error; |
| |
| if (!(ctrl & GM_SMI_CT_BUSY)) |
| return 0; |
| |
| udelay(10); |
| } |
| |
| dev_warn(&hw->pdev->dev,"%s: phy write timeout\n", hw->dev[port]->name); |
| return -ETIMEDOUT; |
| |
| io_error: |
| dev_err(&hw->pdev->dev, "%s: phy I/O error\n", hw->dev[port]->name); |
| return -EIO; |
| } |
| |
| static int __gm_phy_read(struct sky2_hw *hw, unsigned port, u16 reg, u16 *val) |
| { |
| int i; |
| |
| gma_write16(hw, port, GM_SMI_CTRL, GM_SMI_CT_PHY_AD(PHY_ADDR_MARV) |
| | GM_SMI_CT_REG_AD(reg) | GM_SMI_CT_OP_RD); |
| |
| for (i = 0; i < PHY_RETRIES; i++) { |
| u16 ctrl = gma_read16(hw, port, GM_SMI_CTRL); |
| if (ctrl == 0xffff) |
| goto io_error; |
| |
| if (ctrl & GM_SMI_CT_RD_VAL) { |
| *val = gma_read16(hw, port, GM_SMI_DATA); |
| return 0; |
| } |
| |
| udelay(10); |
| } |
| |
| dev_warn(&hw->pdev->dev, "%s: phy read timeout\n", hw->dev[port]->name); |
| return -ETIMEDOUT; |
| io_error: |
| dev_err(&hw->pdev->dev, "%s: phy I/O error\n", hw->dev[port]->name); |
| return -EIO; |
| } |
| |
| static inline u16 gm_phy_read(struct sky2_hw *hw, unsigned port, u16 reg) |
| { |
| u16 v; |
| __gm_phy_read(hw, port, reg, &v); |
| return v; |
| } |
| |
| |
| static void sky2_power_on(struct sky2_hw *hw) |
| { |
| /* switch power to VCC (WA for VAUX problem) */ |
| sky2_write8(hw, B0_POWER_CTRL, |
| PC_VAUX_ENA | PC_VCC_ENA | PC_VAUX_OFF | PC_VCC_ON); |
| |
| /* disable Core Clock Division, */ |
| sky2_write32(hw, B2_Y2_CLK_CTRL, Y2_CLK_DIV_DIS); |
| |
| if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1) |
| /* enable bits are inverted */ |
| sky2_write8(hw, B2_Y2_CLK_GATE, |
| Y2_PCI_CLK_LNK1_DIS | Y2_COR_CLK_LNK1_DIS | |
| Y2_CLK_GAT_LNK1_DIS | Y2_PCI_CLK_LNK2_DIS | |
| Y2_COR_CLK_LNK2_DIS | Y2_CLK_GAT_LNK2_DIS); |
| else |
| sky2_write8(hw, B2_Y2_CLK_GATE, 0); |
| |
| if (hw->flags & SKY2_HW_ADV_POWER_CTL) { |
| u32 reg; |
| |
| sky2_pci_write32(hw, PCI_DEV_REG3, 0); |
| |
| reg = sky2_pci_read32(hw, PCI_DEV_REG4); |
| /* set all bits to 0 except bits 15..12 and 8 */ |
| reg &= P_ASPM_CONTROL_MSK; |
| sky2_pci_write32(hw, PCI_DEV_REG4, reg); |
| |
| reg = sky2_pci_read32(hw, PCI_DEV_REG5); |
| /* set all bits to 0 except bits 28 & 27 */ |
| reg &= P_CTL_TIM_VMAIN_AV_MSK; |
| sky2_pci_write32(hw, PCI_DEV_REG5, reg); |
| |
| sky2_pci_write32(hw, PCI_CFG_REG_1, 0); |
| |
| /* Enable workaround for dev 4.107 on Yukon-Ultra & Extreme */ |
| reg = sky2_read32(hw, B2_GP_IO); |
| reg |= GLB_GPIO_STAT_RACE_DIS; |
| sky2_write32(hw, B2_GP_IO, reg); |
| |
| sky2_read32(hw, B2_GP_IO); |
| } |
| |
| /* Turn on "driver loaded" LED */ |
| sky2_write16(hw, B0_CTST, Y2_LED_STAT_ON); |
| } |
| |
| static void sky2_power_aux(struct sky2_hw *hw) |
| { |
| if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1) |
| sky2_write8(hw, B2_Y2_CLK_GATE, 0); |
| else |
| /* enable bits are inverted */ |
| sky2_write8(hw, B2_Y2_CLK_GATE, |
| Y2_PCI_CLK_LNK1_DIS | Y2_COR_CLK_LNK1_DIS | |
| Y2_CLK_GAT_LNK1_DIS | Y2_PCI_CLK_LNK2_DIS | |
| Y2_COR_CLK_LNK2_DIS | Y2_CLK_GAT_LNK2_DIS); |
| |
| /* switch power to VAUX if supported and PME from D3cold */ |
| if ( (sky2_read32(hw, B0_CTST) & Y2_VAUX_AVAIL) && |
| pci_pme_capable(hw->pdev, PCI_D3cold)) |
| sky2_write8(hw, B0_POWER_CTRL, |
| (PC_VAUX_ENA | PC_VCC_ENA | |
| PC_VAUX_ON | PC_VCC_OFF)); |
| |
| /* turn off "driver loaded LED" */ |
| sky2_write16(hw, B0_CTST, Y2_LED_STAT_OFF); |
| } |
| |
| static void sky2_gmac_reset(struct sky2_hw *hw, unsigned port) |
| { |
| u16 reg; |
| |
| /* disable all GMAC IRQ's */ |
| sky2_write8(hw, SK_REG(port, GMAC_IRQ_MSK), 0); |
| |
| gma_write16(hw, port, GM_MC_ADDR_H1, 0); /* clear MC hash */ |
| gma_write16(hw, port, GM_MC_ADDR_H2, 0); |
| gma_write16(hw, port, GM_MC_ADDR_H3, 0); |
| gma_write16(hw, port, GM_MC_ADDR_H4, 0); |
| |
| reg = gma_read16(hw, port, GM_RX_CTRL); |
| reg |= GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA; |
| gma_write16(hw, port, GM_RX_CTRL, reg); |
| } |
| |
| /* flow control to advertise bits */ |
| static const u16 copper_fc_adv[] = { |
| [FC_NONE] = 0, |
| [FC_TX] = PHY_M_AN_ASP, |
| [FC_RX] = PHY_M_AN_PC, |
| [FC_BOTH] = PHY_M_AN_PC | PHY_M_AN_ASP, |
| }; |
| |
| /* flow control to advertise bits when using 1000BaseX */ |
| static const u16 fiber_fc_adv[] = { |
| [FC_NONE] = PHY_M_P_NO_PAUSE_X, |
| [FC_TX] = PHY_M_P_ASYM_MD_X, |
| [FC_RX] = PHY_M_P_SYM_MD_X, |
| [FC_BOTH] = PHY_M_P_BOTH_MD_X, |
| }; |
| |
| /* flow control to GMA disable bits */ |
| static const u16 gm_fc_disable[] = { |
| [FC_NONE] = GM_GPCR_FC_RX_DIS | GM_GPCR_FC_TX_DIS, |
| [FC_TX] = GM_GPCR_FC_RX_DIS, |
| [FC_RX] = GM_GPCR_FC_TX_DIS, |
| [FC_BOTH] = 0, |
| }; |
| |
| |
| static void sky2_phy_init(struct sky2_hw *hw, unsigned port) |
| { |
| struct sky2_port *sky2 = netdev_priv(hw->dev[port]); |
| u16 ctrl, ct1000, adv, pg, ledctrl, ledover, reg; |
| |
| if ( (sky2->flags & SKY2_FLAG_AUTO_SPEED) && |
| !(hw->flags & SKY2_HW_NEWER_PHY)) { |
| u16 ectrl = gm_phy_read(hw, port, PHY_MARV_EXT_CTRL); |
| |
| ectrl &= ~(PHY_M_EC_M_DSC_MSK | PHY_M_EC_S_DSC_MSK | |
| PHY_M_EC_MAC_S_MSK); |
| ectrl |= PHY_M_EC_MAC_S(MAC_TX_CLK_25_MHZ); |
| |
| /* on PHY 88E1040 Rev.D0 (and newer) downshift control changed */ |
| if (hw->chip_id == CHIP_ID_YUKON_EC) |
| /* set downshift counter to 3x and enable downshift */ |
| ectrl |= PHY_M_EC_DSC_2(2) | PHY_M_EC_DOWN_S_ENA; |
| else |
| /* set master & slave downshift counter to 1x */ |
| ectrl |= PHY_M_EC_M_DSC(0) | PHY_M_EC_S_DSC(1); |
| |
| gm_phy_write(hw, port, PHY_MARV_EXT_CTRL, ectrl); |
| } |
| |
| ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL); |
| if (sky2_is_copper(hw)) { |
| if (!(hw->flags & SKY2_HW_GIGABIT)) { |
| /* enable automatic crossover */ |
| ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO) >> 1; |
| |
| if (hw->chip_id == CHIP_ID_YUKON_FE_P && |
| hw->chip_rev == CHIP_REV_YU_FE2_A0) { |
| u16 spec; |
| |
| /* Enable Class A driver for FE+ A0 */ |
| spec = gm_phy_read(hw, port, PHY_MARV_FE_SPEC_2); |
| spec |= PHY_M_FESC_SEL_CL_A; |
| gm_phy_write(hw, port, PHY_MARV_FE_SPEC_2, spec); |
| } |
| } else { |
| /* disable energy detect */ |
| ctrl &= ~PHY_M_PC_EN_DET_MSK; |
| |
| /* enable automatic crossover */ |
| ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO); |
| |
| /* downshift on PHY 88E1112 and 88E1149 is changed */ |
| if ( (sky2->flags & SKY2_FLAG_AUTO_SPEED) |
| && (hw->flags & SKY2_HW_NEWER_PHY)) { |
| /* set downshift counter to 3x and enable downshift */ |
| ctrl &= ~PHY_M_PC_DSC_MSK; |
| ctrl |= PHY_M_PC_DSC(2) | PHY_M_PC_DOWN_S_ENA; |
| } |
| } |
| } else { |
| /* workaround for deviation #4.88 (CRC errors) */ |
| /* disable Automatic Crossover */ |
| |
| ctrl &= ~PHY_M_PC_MDIX_MSK; |
| } |
| |
| gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl); |
| |
| /* special setup for PHY 88E1112 Fiber */ |
| if (hw->chip_id == CHIP_ID_YUKON_XL && (hw->flags & SKY2_HW_FIBRE_PHY)) { |
| pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR); |
| |
| /* Fiber: select 1000BASE-X only mode MAC Specific Ctrl Reg. */ |
| gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 2); |
| ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL); |
| ctrl &= ~PHY_M_MAC_MD_MSK; |
| ctrl |= PHY_M_MAC_MODE_SEL(PHY_M_MAC_MD_1000BX); |
| gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl); |
| |
| if (hw->pmd_type == 'P') { |
| /* select page 1 to access Fiber registers */ |
| gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 1); |
| |
| /* for SFP-module set SIGDET polarity to low */ |
| ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL); |
| ctrl |= PHY_M_FIB_SIGD_POL; |
| gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl); |
| } |
| |
| gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg); |
| } |
| |
| ctrl = PHY_CT_RESET; |
| ct1000 = 0; |
| adv = PHY_AN_CSMA; |
| reg = 0; |
| |
| if (sky2->flags & SKY2_FLAG_AUTO_SPEED) { |
| if (sky2_is_copper(hw)) { |
| if (sky2->advertising & ADVERTISED_1000baseT_Full) |
| ct1000 |= PHY_M_1000C_AFD; |
| if (sky2->advertising & ADVERTISED_1000baseT_Half) |
| ct1000 |= PHY_M_1000C_AHD; |
| if (sky2->advertising & ADVERTISED_100baseT_Full) |
| adv |= PHY_M_AN_100_FD; |
| if (sky2->advertising & ADVERTISED_100baseT_Half) |
| adv |= PHY_M_AN_100_HD; |
| if (sky2->advertising & ADVERTISED_10baseT_Full) |
| adv |= PHY_M_AN_10_FD; |
| if (sky2->advertising & ADVERTISED_10baseT_Half) |
| adv |= PHY_M_AN_10_HD; |
| |
| } else { /* special defines for FIBER (88E1040S only) */ |
| if (sky2->advertising & ADVERTISED_1000baseT_Full) |
| adv |= PHY_M_AN_1000X_AFD; |
| if (sky2->advertising & ADVERTISED_1000baseT_Half) |
| adv |= PHY_M_AN_1000X_AHD; |
| } |
| |
| /* Restart Auto-negotiation */ |
| ctrl |= PHY_CT_ANE | PHY_CT_RE_CFG; |
| } else { |
| /* forced speed/duplex settings */ |
| ct1000 = PHY_M_1000C_MSE; |
| |
| /* Disable auto update for duplex flow control and duplex */ |
| reg |= GM_GPCR_AU_DUP_DIS | GM_GPCR_AU_SPD_DIS; |
| |
| switch (sky2->speed) { |
| case SPEED_1000: |
| ctrl |= PHY_CT_SP1000; |
| reg |= GM_GPCR_SPEED_1000; |
| break; |
| case SPEED_100: |
| ctrl |= PHY_CT_SP100; |
| reg |= GM_GPCR_SPEED_100; |
| break; |
| } |
| |
| if (sky2->duplex == DUPLEX_FULL) { |
| reg |= GM_GPCR_DUP_FULL; |
| ctrl |= PHY_CT_DUP_MD; |
| } else if (sky2->speed < SPEED_1000) |
| sky2->flow_mode = FC_NONE; |
| } |
| |
| if (sky2->flags & SKY2_FLAG_AUTO_PAUSE) { |
| if (sky2_is_copper(hw)) |
| adv |= copper_fc_adv[sky2->flow_mode]; |
| else |
| adv |= fiber_fc_adv[sky2->flow_mode]; |
| } else { |
| reg |= GM_GPCR_AU_FCT_DIS; |
| reg |= gm_fc_disable[sky2->flow_mode]; |
| |
| /* Forward pause packets to GMAC? */ |
| if (sky2->flow_mode & FC_RX) |
| sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_ON); |
| else |
| sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF); |
| } |
| |
| gma_write16(hw, port, GM_GP_CTRL, reg); |
| |
| if (hw->flags & SKY2_HW_GIGABIT) |
| gm_phy_write(hw, port, PHY_MARV_1000T_CTRL, ct1000); |
| |
| gm_phy_write(hw, port, PHY_MARV_AUNE_ADV, adv); |
| gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl); |
| |
| /* Setup Phy LED's */ |
| ledctrl = PHY_M_LED_PULS_DUR(PULS_170MS); |
| ledover = 0; |
| |
| switch (hw->chip_id) { |
| case CHIP_ID_YUKON_FE: |
| /* on 88E3082 these bits are at 11..9 (shifted left) */ |
| ledctrl |= PHY_M_LED_BLINK_RT(BLINK_84MS) << 1; |
| |
| ctrl = gm_phy_read(hw, port, PHY_MARV_FE_LED_PAR); |
| |
| /* delete ACT LED control bits */ |
| ctrl &= ~PHY_M_FELP_LED1_MSK; |
| /* change ACT LED control to blink mode */ |
| ctrl |= PHY_M_FELP_LED1_CTRL(LED_PAR_CTRL_ACT_BL); |
| gm_phy_write(hw, port, PHY_MARV_FE_LED_PAR, ctrl); |
| break; |
| |
| case CHIP_ID_YUKON_FE_P: |
| /* Enable Link Partner Next Page */ |
| ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL); |
| ctrl |= PHY_M_PC_ENA_LIP_NP; |
| |
| /* disable Energy Detect and enable scrambler */ |
| ctrl &= ~(PHY_M_PC_ENA_ENE_DT | PHY_M_PC_DIS_SCRAMB); |
| gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl); |
| |
| /* set LED2 -> ACT, LED1 -> LINK, LED0 -> SPEED */ |
| ctrl = PHY_M_FELP_LED2_CTRL(LED_PAR_CTRL_ACT_BL) | |
| PHY_M_FELP_LED1_CTRL(LED_PAR_CTRL_LINK) | |
| PHY_M_FELP_LED0_CTRL(LED_PAR_CTRL_SPEED); |
| |
| gm_phy_write(hw, port, PHY_MARV_FE_LED_PAR, ctrl); |
| break; |
| |
| case CHIP_ID_YUKON_XL: |
| pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR); |
| |
| /* select page 3 to access LED control register */ |
| gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3); |
| |
| /* set LED Function Control register */ |
| gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, |
| (PHY_M_LEDC_LOS_CTRL(1) | /* LINK/ACT */ |
| PHY_M_LEDC_INIT_CTRL(7) | /* 10 Mbps */ |
| PHY_M_LEDC_STA1_CTRL(7) | /* 100 Mbps */ |
| PHY_M_LEDC_STA0_CTRL(7))); /* 1000 Mbps */ |
| |
| /* set Polarity Control register */ |
| gm_phy_write(hw, port, PHY_MARV_PHY_STAT, |
| (PHY_M_POLC_LS1_P_MIX(4) | |
| PHY_M_POLC_IS0_P_MIX(4) | |
| PHY_M_POLC_LOS_CTRL(2) | |
| PHY_M_POLC_INIT_CTRL(2) | |
| PHY_M_POLC_STA1_CTRL(2) | |
| PHY_M_POLC_STA0_CTRL(2))); |
| |
| /* restore page register */ |
| gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg); |
| break; |
| |
| case CHIP_ID_YUKON_EC_U: |
| case CHIP_ID_YUKON_EX: |
| case CHIP_ID_YUKON_SUPR: |
| pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR); |
| |
| /* select page 3 to access LED control register */ |
| gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3); |
| |
| /* set LED Function Control register */ |
| gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, |
| (PHY_M_LEDC_LOS_CTRL(1) | /* LINK/ACT */ |
| PHY_M_LEDC_INIT_CTRL(8) | /* 10 Mbps */ |
| PHY_M_LEDC_STA1_CTRL(7) | /* 100 Mbps */ |
| PHY_M_LEDC_STA0_CTRL(7)));/* 1000 Mbps */ |
| |
| /* set Blink Rate in LED Timer Control Register */ |
| gm_phy_write(hw, port, PHY_MARV_INT_MASK, |
| ledctrl | PHY_M_LED_BLINK_RT(BLINK_84MS)); |
| /* restore page register */ |
| gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg); |
| break; |
| |
| default: |
| /* set Tx LED (LED_TX) to blink mode on Rx OR Tx activity */ |
| ledctrl |= PHY_M_LED_BLINK_RT(BLINK_84MS) | PHY_M_LEDC_TX_CTRL; |
| |
| /* turn off the Rx LED (LED_RX) */ |
| ledover |= PHY_M_LED_MO_RX(MO_LED_OFF); |
| } |
| |
| if (hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_UL_2) { |
| /* apply fixes in PHY AFE */ |
| gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 255); |
| |
| /* increase differential signal amplitude in 10BASE-T */ |
| gm_phy_write(hw, port, 0x18, 0xaa99); |
| gm_phy_write(hw, port, 0x17, 0x2011); |
| |
| if (hw->chip_id == CHIP_ID_YUKON_EC_U) { |
| /* fix for IEEE A/B Symmetry failure in 1000BASE-T */ |
| gm_phy_write(hw, port, 0x18, 0xa204); |
| gm_phy_write(hw, port, 0x17, 0x2002); |
| } |
| |
| /* set page register to 0 */ |
| gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0); |
| } else if (hw->chip_id == CHIP_ID_YUKON_FE_P && |
| hw->chip_rev == CHIP_REV_YU_FE2_A0) { |
| /* apply workaround for integrated resistors calibration */ |
| gm_phy_write(hw, port, PHY_MARV_PAGE_ADDR, 17); |
| gm_phy_write(hw, port, PHY_MARV_PAGE_DATA, 0x3f60); |
| } else if (hw->chip_id != CHIP_ID_YUKON_EX && |
| hw->chip_id < CHIP_ID_YUKON_SUPR) { |
| /* no effect on Yukon-XL */ |
| gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl); |
| |
| if ( !(sky2->flags & SKY2_FLAG_AUTO_SPEED) |
| || sky2->speed == SPEED_100) { |
| /* turn on 100 Mbps LED (LED_LINK100) */ |
| ledover |= PHY_M_LED_MO_100(MO_LED_ON); |
| } |
| |
| if (ledover) |
| gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover); |
| |
| } |
| |
| /* Enable phy interrupt on auto-negotiation complete (or link up) */ |
| if (sky2->flags & SKY2_FLAG_AUTO_SPEED) |
| gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_AN_COMPL); |
| else |
| gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK); |
| } |
| |
| static const u32 phy_power[] = { PCI_Y2_PHY1_POWD, PCI_Y2_PHY2_POWD }; |
| static const u32 coma_mode[] = { PCI_Y2_PHY1_COMA, PCI_Y2_PHY2_COMA }; |
| |
| static void sky2_phy_power_up(struct sky2_hw *hw, unsigned port) |
| { |
| u32 reg1; |
| |
| sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON); |
| reg1 = sky2_pci_read32(hw, PCI_DEV_REG1); |
| reg1 &= ~phy_power[port]; |
| |
| if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > 1) |
| reg1 |= coma_mode[port]; |
| |
| sky2_pci_write32(hw, PCI_DEV_REG1, reg1); |
| sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF); |
| sky2_pci_read32(hw, PCI_DEV_REG1); |
| |
| if (hw->chip_id == CHIP_ID_YUKON_FE) |
| gm_phy_write(hw, port, PHY_MARV_CTRL, PHY_CT_ANE); |
| else if (hw->flags & SKY2_HW_ADV_POWER_CTL) |
| sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_CLR); |
| } |
| |
| static void sky2_phy_power_down(struct sky2_hw *hw, unsigned port) |
| { |
| u32 reg1; |
| u16 ctrl; |
| |
| /* release GPHY Control reset */ |
| sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_CLR); |
| |
| /* release GMAC reset */ |
| sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_CLR); |
| |
| if (hw->flags & SKY2_HW_NEWER_PHY) { |
| /* select page 2 to access MAC control register */ |
| gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 2); |
| |
| ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL); |
| /* allow GMII Power Down */ |
| ctrl &= ~PHY_M_MAC_GMIF_PUP; |
| gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl); |
| |
| /* set page register back to 0 */ |
| gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0); |
| } |
| |
| /* setup General Purpose Control Register */ |
| gma_write16(hw, port, GM_GP_CTRL, |
| GM_GPCR_FL_PASS | GM_GPCR_SPEED_100 | |
| GM_GPCR_AU_DUP_DIS | GM_GPCR_AU_FCT_DIS | |
| GM_GPCR_AU_SPD_DIS); |
| |
| if (hw->chip_id != CHIP_ID_YUKON_EC) { |
| if (hw->chip_id == CHIP_ID_YUKON_EC_U) { |
| /* select page 2 to access MAC control register */ |
| gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 2); |
| |
| ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL); |
| /* enable Power Down */ |
| ctrl |= PHY_M_PC_POW_D_ENA; |
| gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl); |
| |
| /* set page register back to 0 */ |
| gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0); |
| } |
| |
| /* set IEEE compatible Power Down Mode (dev. #4.99) */ |
| gm_phy_write(hw, port, PHY_MARV_CTRL, PHY_CT_PDOWN); |
| } |
| |
| sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON); |
| reg1 = sky2_pci_read32(hw, PCI_DEV_REG1); |
| reg1 |= phy_power[port]; /* set PHY to PowerDown/COMA Mode */ |
| sky2_pci_write32(hw, PCI_DEV_REG1, reg1); |
| sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF); |
| } |
| |
| /* Force a renegotiation */ |
| static void sky2_phy_reinit(struct sky2_port *sky2) |
| { |
| spin_lock_bh(&sky2->phy_lock); |
| sky2_phy_init(sky2->hw, sky2->port); |
| spin_unlock_bh(&sky2->phy_lock); |
| } |
| |
| /* Put device in state to listen for Wake On Lan */ |
| static void sky2_wol_init(struct sky2_port *sky2) |
| { |
| struct sky2_hw *hw = sky2->hw; |
| unsigned port = sky2->port; |
| enum flow_control save_mode; |
| u16 ctrl; |
| u32 reg1; |
| |
| /* Bring hardware out of reset */ |
| sky2_write16(hw, B0_CTST, CS_RST_CLR); |
| sky2_write16(hw, SK_REG(port, GMAC_LINK_CTRL), GMLC_RST_CLR); |
| |
| sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_CLR); |
| sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_CLR); |
| |
| /* Force to 10/100 |
| * sky2_reset will re-enable on resume |
| */ |
| save_mode = sky2->flow_mode; |
| ctrl = sky2->advertising; |
| |
| sky2->advertising &= ~(ADVERTISED_1000baseT_Half|ADVERTISED_1000baseT_Full); |
| sky2->flow_mode = FC_NONE; |
| |
| spin_lock_bh(&sky2->phy_lock); |
| sky2_phy_power_up(hw, port); |
| sky2_phy_init(hw, port); |
| spin_unlock_bh(&sky2->phy_lock); |
| |
| sky2->flow_mode = save_mode; |
| sky2->advertising = ctrl; |
| |
| /* Set GMAC to no flow control and auto update for speed/duplex */ |
| gma_write16(hw, port, GM_GP_CTRL, |
| GM_GPCR_FC_TX_DIS|GM_GPCR_TX_ENA|GM_GPCR_RX_ENA| |
| GM_GPCR_DUP_FULL|GM_GPCR_FC_RX_DIS|GM_GPCR_AU_FCT_DIS); |
| |
| /* Set WOL address */ |
| memcpy_toio(hw->regs + WOL_REGS(port, WOL_MAC_ADDR), |
| sky2->netdev->dev_addr, ETH_ALEN); |
| |
| /* Turn on appropriate WOL control bits */ |
| sky2_write16(hw, WOL_REGS(port, WOL_CTRL_STAT), WOL_CTL_CLEAR_RESULT); |
| ctrl = 0; |
| if (sky2->wol & WAKE_PHY) |
| ctrl |= WOL_CTL_ENA_PME_ON_LINK_CHG|WOL_CTL_ENA_LINK_CHG_UNIT; |
| else |
| ctrl |= WOL_CTL_DIS_PME_ON_LINK_CHG|WOL_CTL_DIS_LINK_CHG_UNIT; |
| |
| if (sky2->wol & WAKE_MAGIC) |
| ctrl |= WOL_CTL_ENA_PME_ON_MAGIC_PKT|WOL_CTL_ENA_MAGIC_PKT_UNIT; |
| else |
| ctrl |= WOL_CTL_DIS_PME_ON_MAGIC_PKT|WOL_CTL_DIS_MAGIC_PKT_UNIT; |
| |
| ctrl |= WOL_CTL_DIS_PME_ON_PATTERN|WOL_CTL_DIS_PATTERN_UNIT; |
| sky2_write16(hw, WOL_REGS(port, WOL_CTRL_STAT), ctrl); |
| |
| /* Turn on legacy PCI-Express PME mode */ |
| reg1 = sky2_pci_read32(hw, PCI_DEV_REG1); |
| reg1 |= PCI_Y2_PME_LEGACY; |
| sky2_pci_write32(hw, PCI_DEV_REG1, reg1); |
| |
| /* block receiver */ |
| sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET); |
| |
| } |
| |
| static void sky2_set_tx_stfwd(struct sky2_hw *hw, unsigned port) |
| { |
| struct net_device *dev = hw->dev[port]; |
| |
| if ( (hw->chip_id == CHIP_ID_YUKON_EX && |
| hw->chip_rev != CHIP_REV_YU_EX_A0) || |
| hw->chip_id == CHIP_ID_YUKON_FE_P || |
| hw->chip_id == CHIP_ID_YUKON_SUPR) { |
| /* Yukon-Extreme B0 and further Extreme devices */ |
| /* enable Store & Forward mode for TX */ |
| |
| if (dev->mtu <= ETH_DATA_LEN) |
| sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), |
| TX_JUMBO_DIS | TX_STFW_ENA); |
| |
| else |
| sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), |
| TX_JUMBO_ENA| TX_STFW_ENA); |
| } else { |
| if (dev->mtu <= ETH_DATA_LEN) |
| sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), TX_STFW_ENA); |
| else { |
| /* set Tx GMAC FIFO Almost Empty Threshold */ |
| sky2_write32(hw, SK_REG(port, TX_GMF_AE_THR), |
| (ECU_JUMBO_WM << 16) | ECU_AE_THR); |
| |
| sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), TX_STFW_DIS); |
| |
| /* Can't do offload because of lack of store/forward */ |
| dev->features &= ~(NETIF_F_TSO | NETIF_F_SG | NETIF_F_ALL_CSUM); |
| } |
| } |
| } |
| |
| static void sky2_mac_init(struct sky2_hw *hw, unsigned port) |
| { |
| struct sky2_port *sky2 = netdev_priv(hw->dev[port]); |
| u16 reg; |
| u32 rx_reg; |
| int i; |
| const u8 *addr = hw->dev[port]->dev_addr; |
| |
| sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET); |
| sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_CLR); |
| |
| sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_CLR); |
| |
| if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0 && port == 1) { |
| /* WA DEV_472 -- looks like crossed wires on port 2 */ |
| /* clear GMAC 1 Control reset */ |
| sky2_write8(hw, SK_REG(0, GMAC_CTRL), GMC_RST_CLR); |
| do { |
| sky2_write8(hw, SK_REG(1, GMAC_CTRL), GMC_RST_SET); |
| sky2_write8(hw, SK_REG(1, GMAC_CTRL), GMC_RST_CLR); |
| } while (gm_phy_read(hw, 1, PHY_MARV_ID0) != PHY_MARV_ID0_VAL || |
| gm_phy_read(hw, 1, PHY_MARV_ID1) != PHY_MARV_ID1_Y2 || |
| gm_phy_read(hw, 1, PHY_MARV_INT_MASK) != 0); |
| } |
| |
| sky2_read16(hw, SK_REG(port, GMAC_IRQ_SRC)); |
| |
| /* Enable Transmit FIFO Underrun */ |
| sky2_write8(hw, SK_REG(port, GMAC_IRQ_MSK), GMAC_DEF_MSK); |
| |
| spin_lock_bh(&sky2->phy_lock); |
| sky2_phy_power_up(hw, port); |
| sky2_phy_init(hw, port); |
| spin_unlock_bh(&sky2->phy_lock); |
| |
| /* MIB clear */ |
| reg = gma_read16(hw, port, GM_PHY_ADDR); |
| gma_write16(hw, port, GM_PHY_ADDR, reg | GM_PAR_MIB_CLR); |
| |
| for (i = GM_MIB_CNT_BASE; i <= GM_MIB_CNT_END; i += 4) |
| gma_read16(hw, port, i); |
| gma_write16(hw, port, GM_PHY_ADDR, reg); |
| |
| /* transmit control */ |
| gma_write16(hw, port, GM_TX_CTRL, TX_COL_THR(TX_COL_DEF)); |
| |
| /* receive control reg: unicast + multicast + no FCS */ |
| gma_write16(hw, port, GM_RX_CTRL, |
| GM_RXCR_UCF_ENA | GM_RXCR_CRC_DIS | GM_RXCR_MCF_ENA); |
| |
| /* transmit flow control */ |
| gma_write16(hw, port, GM_TX_FLOW_CTRL, 0xffff); |
| |
| /* transmit parameter */ |
| gma_write16(hw, port, GM_TX_PARAM, |
| TX_JAM_LEN_VAL(TX_JAM_LEN_DEF) | |
| TX_JAM_IPG_VAL(TX_JAM_IPG_DEF) | |
| TX_IPG_JAM_DATA(TX_IPG_JAM_DEF) | |
| TX_BACK_OFF_LIM(TX_BOF_LIM_DEF)); |
| |
| /* serial mode register */ |
| reg = DATA_BLIND_VAL(DATA_BLIND_DEF) | |
| GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF); |
| |
| if (hw->dev[port]->mtu > ETH_DATA_LEN) |
| reg |= GM_SMOD_JUMBO_ENA; |
| |
| gma_write16(hw, port, GM_SERIAL_MODE, reg); |
| |
| /* virtual address for data */ |
| gma_set_addr(hw, port, GM_SRC_ADDR_2L, addr); |
| |
| /* physical address: used for pause frames */ |
| gma_set_addr(hw, port, GM_SRC_ADDR_1L, addr); |
| |
| /* ignore counter overflows */ |
| gma_write16(hw, port, GM_TX_IRQ_MSK, 0); |
| gma_write16(hw, port, GM_RX_IRQ_MSK, 0); |
| gma_write16(hw, port, GM_TR_IRQ_MSK, 0); |
| |
| /* Configure Rx MAC FIFO */ |
| sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_CLR); |
| rx_reg = GMF_OPER_ON | GMF_RX_F_FL_ON; |
| if (hw->chip_id == CHIP_ID_YUKON_EX || |
| hw->chip_id == CHIP_ID_YUKON_FE_P) |
| rx_reg |= GMF_RX_OVER_ON; |
| |
| sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T), rx_reg); |
| |
| if (hw->chip_id == CHIP_ID_YUKON_XL) { |
| /* Hardware errata - clear flush mask */ |
| sky2_write16(hw, SK_REG(port, RX_GMF_FL_MSK), 0); |
| } else { |
| /* Flush Rx MAC FIFO on any flow control or error */ |
| sky2_write16(hw, SK_REG(port, RX_GMF_FL_MSK), GMR_FS_ANY_ERR); |
| } |
| |
| /* Set threshold to 0xa (64 bytes) + 1 to workaround pause bug */ |
| reg = RX_GMF_FL_THR_DEF + 1; |
| /* Another magic mystery workaround from sk98lin */ |
| if (hw->chip_id == CHIP_ID_YUKON_FE_P && |
| hw->chip_rev == CHIP_REV_YU_FE2_A0) |
| reg = 0x178; |
| sky2_write16(hw, SK_REG(port, RX_GMF_FL_THR), reg); |
| |
| /* Configure Tx MAC FIFO */ |
| sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_CLR); |
| sky2_write16(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_OPER_ON); |
| |
| /* On chips without ram buffer, pause is controled by MAC level */ |
| if (!(hw->flags & SKY2_HW_RAM_BUFFER)) { |
| sky2_write8(hw, SK_REG(port, RX_GMF_LP_THR), 768/8); |
| sky2_write8(hw, SK_REG(port, RX_GMF_UP_THR), 1024/8); |
| |
| sky2_set_tx_stfwd(hw, port); |
| } |
| |
| if (hw->chip_id == CHIP_ID_YUKON_FE_P && |
| hw->chip_rev == CHIP_REV_YU_FE2_A0) { |
| /* disable dynamic watermark */ |
| reg = sky2_read16(hw, SK_REG(port, TX_GMF_EA)); |
| reg &= ~TX_DYN_WM_ENA; |
| sky2_write16(hw, SK_REG(port, TX_GMF_EA), reg); |
| } |
| } |
| |
| /* Assign Ram Buffer allocation to queue */ |
| static void sky2_ramset(struct sky2_hw *hw, u16 q, u32 start, u32 space) |
| { |
| u32 end; |
| |
| /* convert from K bytes to qwords used for hw register */ |
| start *= 1024/8; |
| space *= 1024/8; |
| end = start + space - 1; |
| |
| sky2_write8(hw, RB_ADDR(q, RB_CTRL), RB_RST_CLR); |
| sky2_write32(hw, RB_ADDR(q, RB_START), start); |
| sky2_write32(hw, RB_ADDR(q, RB_END), end); |
| sky2_write32(hw, RB_ADDR(q, RB_WP), start); |
| sky2_write32(hw, RB_ADDR(q, RB_RP), start); |
| |
| if (q == Q_R1 || q == Q_R2) { |
| u32 tp = space - space/4; |
| |
| /* On receive queue's set the thresholds |
| * give receiver priority when > 3/4 full |
| * send pause when down to 2K |
| */ |
| sky2_write32(hw, RB_ADDR(q, RB_RX_UTHP), tp); |
| sky2_write32(hw, RB_ADDR(q, RB_RX_LTHP), space/2); |
| |
| tp = space - 2048/8; |
| sky2_write32(hw, RB_ADDR(q, RB_RX_UTPP), tp); |
| sky2_write32(hw, RB_ADDR(q, RB_RX_LTPP), space/4); |
| } else { |
| /* Enable store & forward on Tx queue's because |
| * Tx FIFO is only 1K on Yukon |
| */ |
| sky2_write8(hw, RB_ADDR(q, RB_CTRL), RB_ENA_STFWD); |
| } |
| |
| sky2_write8(hw, RB_ADDR(q, RB_CTRL), RB_ENA_OP_MD); |
| sky2_read8(hw, RB_ADDR(q, RB_CTRL)); |
| } |
| |
| /* Setup Bus Memory Interface */ |
| static void sky2_qset(struct sky2_hw *hw, u16 q) |
| { |
| sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_CLR_RESET); |
| sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_OPER_INIT); |
| sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_FIFO_OP_ON); |
| sky2_write32(hw, Q_ADDR(q, Q_WM), BMU_WM_DEFAULT); |
| } |
| |
| /* Setup prefetch unit registers. This is the interface between |
| * hardware and driver list elements |
| */ |
| static void sky2_prefetch_init(struct sky2_hw *hw, u32 qaddr, |
| dma_addr_t addr, u32 last) |
| { |
| sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL), PREF_UNIT_RST_SET); |
| sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL), PREF_UNIT_RST_CLR); |
| sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_ADDR_HI), upper_32_bits(addr)); |
| sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_ADDR_LO), lower_32_bits(addr)); |
| sky2_write16(hw, Y2_QADDR(qaddr, PREF_UNIT_LAST_IDX), last); |
| sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL), PREF_UNIT_OP_ON); |
| |
| sky2_read32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL)); |
| } |
| |
| static inline struct sky2_tx_le *get_tx_le(struct sky2_port *sky2, u16 *slot) |
| { |
| struct sky2_tx_le *le = sky2->tx_le + *slot; |
| struct tx_ring_info *re = sky2->tx_ring + *slot; |
| |
| *slot = RING_NEXT(*slot, sky2->tx_ring_size); |
| re->flags = 0; |
| re->skb = NULL; |
| le->ctrl = 0; |
| return le; |
| } |
| |
| static void tx_init(struct sky2_port *sky2) |
| { |
| struct sky2_tx_le *le; |
| |
| sky2->tx_prod = sky2->tx_cons = 0; |
| sky2->tx_tcpsum = 0; |
| sky2->tx_last_mss = 0; |
| |
| le = get_tx_le(sky2, &sky2->tx_prod); |
| le->addr = 0; |
| le->opcode = OP_ADDR64 | HW_OWNER; |
| sky2->tx_last_upper = 0; |
| } |
| |
| /* Update chip's next pointer */ |
| static inline void sky2_put_idx(struct sky2_hw *hw, unsigned q, u16 idx) |
| { |
| /* Make sure write' to descriptors are complete before we tell hardware */ |
| wmb(); |
| sky2_write16(hw, Y2_QADDR(q, PREF_UNIT_PUT_IDX), idx); |
| |
| /* Synchronize I/O on since next processor may write to tail */ |
| mmiowb(); |
| } |
| |
| |
| static inline struct sky2_rx_le *sky2_next_rx(struct sky2_port *sky2) |
| { |
| struct sky2_rx_le *le = sky2->rx_le + sky2->rx_put; |
| sky2->rx_put = RING_NEXT(sky2->rx_put, RX_LE_SIZE); |
| le->ctrl = 0; |
| return le; |
| } |
| |
| /* Build description to hardware for one receive segment */ |
| static void sky2_rx_add(struct sky2_port *sky2, u8 op, |
| dma_addr_t map, unsigned len) |
| { |
| struct sky2_rx_le *le; |
| |
| if (sizeof(dma_addr_t) > sizeof(u32)) { |
| le = sky2_next_rx(sky2); |
| le->addr = cpu_to_le32(upper_32_bits(map)); |
| le->opcode = OP_ADDR64 | HW_OWNER; |
| } |
| |
| le = sky2_next_rx(sky2); |
| le->addr = cpu_to_le32(lower_32_bits(map)); |
| le->length = cpu_to_le16(len); |
| le->opcode = op | HW_OWNER; |
| } |
| |
| /* Build description to hardware for one possibly fragmented skb */ |
| static void sky2_rx_submit(struct sky2_port *sky2, |
| const struct rx_ring_info *re) |
| { |
| int i; |
| |
| sky2_rx_add(sky2, OP_PACKET, re->data_addr, sky2->rx_data_size); |
| |
| for (i = 0; i < skb_shinfo(re->skb)->nr_frags; i++) |
| sky2_rx_add(sky2, OP_BUFFER, re->frag_addr[i], PAGE_SIZE); |
| } |
| |
| |
| static int sky2_rx_map_skb(struct pci_dev *pdev, struct rx_ring_info *re, |
| unsigned size) |
| { |
| struct sk_buff *skb = re->skb; |
| int i; |
| |
| re->data_addr = pci_map_single(pdev, skb->data, size, PCI_DMA_FROMDEVICE); |
| if (unlikely(pci_dma_mapping_error(pdev, re->data_addr))) |
| return -EIO; |
| |
| pci_unmap_len_set(re, data_size, size); |
| |
| for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) |
| re->frag_addr[i] = pci_map_page(pdev, |
| skb_shinfo(skb)->frags[i].page, |
| skb_shinfo(skb)->frags[i].page_offset, |
| skb_shinfo(skb)->frags[i].size, |
| PCI_DMA_FROMDEVICE); |
| return 0; |
| } |
| |
| static void sky2_rx_unmap_skb(struct pci_dev *pdev, struct rx_ring_info *re) |
| { |
| struct sk_buff *skb = re->skb; |
| int i; |
| |
| pci_unmap_single(pdev, re->data_addr, pci_unmap_len(re, data_size), |
| PCI_DMA_FROMDEVICE); |
| |
| for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) |
| pci_unmap_page(pdev, re->frag_addr[i], |
| skb_shinfo(skb)->frags[i].size, |
| PCI_DMA_FROMDEVICE); |
| } |
| |
| /* Tell chip where to start receive checksum. |
| * Actually has two checksums, but set both same to avoid possible byte |
| * order problems. |
| */ |
| static void rx_set_checksum(struct sky2_port *sky2) |
| { |
| struct sky2_rx_le *le = sky2_next_rx(sky2); |
| |
| le->addr = cpu_to_le32((ETH_HLEN << 16) | ETH_HLEN); |
| le->ctrl = 0; |
| le->opcode = OP_TCPSTART | HW_OWNER; |
| |
| sky2_write32(sky2->hw, |
| Q_ADDR(rxqaddr[sky2->port], Q_CSR), |
| (sky2->flags & SKY2_FLAG_RX_CHECKSUM) |
| ? BMU_ENA_RX_CHKSUM : BMU_DIS_RX_CHKSUM); |
| } |
| |
| /* |
| * The RX Stop command will not work for Yukon-2 if the BMU does not |
| * reach the end of packet and since we can't make sure that we have |
| * incoming data, we must reset the BMU while it is not doing a DMA |
| * transfer. Since it is possible that the RX path is still active, |
| * the RX RAM buffer will be stopped first, so any possible incoming |
| * data will not trigger a DMA. After the RAM buffer is stopped, the |
| * BMU is polled until any DMA in progress is ended and only then it |
| * will be reset. |
| */ |
| static void sky2_rx_stop(struct sky2_port *sky2) |
| { |
| struct sky2_hw *hw = sky2->hw; |
| unsigned rxq = rxqaddr[sky2->port]; |
| int i; |
| |
| /* disable the RAM Buffer receive queue */ |
| sky2_write8(hw, RB_ADDR(rxq, RB_CTRL), RB_DIS_OP_MD); |
| |
| for (i = 0; i < 0xffff; i++) |
| if (sky2_read8(hw, RB_ADDR(rxq, Q_RSL)) |
| == sky2_read8(hw, RB_ADDR(rxq, Q_RL))) |
| goto stopped; |
| |
| printk(KERN_WARNING PFX "%s: receiver stop failed\n", |
| sky2->netdev->name); |
| stopped: |
| sky2_write32(hw, Q_ADDR(rxq, Q_CSR), BMU_RST_SET | BMU_FIFO_RST); |
| |
| /* reset the Rx prefetch unit */ |
| sky2_write32(hw, Y2_QADDR(rxq, PREF_UNIT_CTRL), PREF_UNIT_RST_SET); |
| mmiowb(); |
| } |
| |
| /* Clean out receive buffer area, assumes receiver hardware stopped */ |
| static void sky2_rx_clean(struct sky2_port *sky2) |
| { |
| unsigned i; |
| |
| memset(sky2->rx_le, 0, RX_LE_BYTES); |
| for (i = 0; i < sky2->rx_pending; i++) { |
| struct rx_ring_info *re = sky2->rx_ring + i; |
| |
| if (re->skb) { |
| sky2_rx_unmap_skb(sky2->hw->pdev, re); |
| kfree_skb(re->skb); |
| re->skb = NULL; |
| } |
| } |
| } |
| |
| /* Basic MII support */ |
| static int sky2_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd) |
| { |
| struct mii_ioctl_data *data = if_mii(ifr); |
| struct sky2_port *sky2 = netdev_priv(dev); |
| struct sky2_hw *hw = sky2->hw; |
| int err = -EOPNOTSUPP; |
| |
| if (!netif_running(dev)) |
| return -ENODEV; /* Phy still in reset */ |
| |
| switch (cmd) { |
| case SIOCGMIIPHY: |
| data->phy_id = PHY_ADDR_MARV; |
| |
| /* fallthru */ |
| case SIOCGMIIREG: { |
| u16 val = 0; |
| |
| spin_lock_bh(&sky2->phy_lock); |
| err = __gm_phy_read(hw, sky2->port, data->reg_num & 0x1f, &val); |
| spin_unlock_bh(&sky2->phy_lock); |
| |
| data->val_out = val; |
| break; |
| } |
| |
| case SIOCSMIIREG: |
| spin_lock_bh(&sky2->phy_lock); |
| err = gm_phy_write(hw, sky2->port, data->reg_num & 0x1f, |
| data->val_in); |
| spin_unlock_bh(&sky2->phy_lock); |
| break; |
| } |
| return err; |
| } |
| |
| #ifdef SKY2_VLAN_TAG_USED |
| static void sky2_set_vlan_mode(struct sky2_hw *hw, u16 port, bool onoff) |
| { |
| if (onoff) { |
| sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T), |
| RX_VLAN_STRIP_ON); |
| sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), |
| TX_VLAN_TAG_ON); |
| } else { |
| sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T), |
| RX_VLAN_STRIP_OFF); |
| sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), |
| TX_VLAN_TAG_OFF); |
| } |
| } |
| |
| static void sky2_vlan_rx_register(struct net_device *dev, struct vlan_group *grp) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| struct sky2_hw *hw = sky2->hw; |
| u16 port = sky2->port; |
| |
| netif_tx_lock_bh(dev); |
| napi_disable(&hw->napi); |
| |
| sky2->vlgrp = grp; |
| sky2_set_vlan_mode(hw, port, grp != NULL); |
| |
| sky2_read32(hw, B0_Y2_SP_LISR); |
| napi_enable(&hw->napi); |
| netif_tx_unlock_bh(dev); |
| } |
| #endif |
| |
| /* Amount of required worst case padding in rx buffer */ |
| static inline unsigned sky2_rx_pad(const struct sky2_hw *hw) |
| { |
| return (hw->flags & SKY2_HW_RAM_BUFFER) ? 8 : 2; |
| } |
| |
| /* |
| * Allocate an skb for receiving. If the MTU is large enough |
| * make the skb non-linear with a fragment list of pages. |
| */ |
| static struct sk_buff *sky2_rx_alloc(struct sky2_port *sky2) |
| { |
| struct sk_buff *skb; |
| int i; |
| |
| skb = netdev_alloc_skb(sky2->netdev, |
| sky2->rx_data_size + sky2_rx_pad(sky2->hw)); |
| if (!skb) |
| goto nomem; |
| |
| if (sky2->hw->flags & SKY2_HW_RAM_BUFFER) { |
| unsigned char *start; |
| /* |
| * Workaround for a bug in FIFO that cause hang |
| * if the FIFO if the receive buffer is not 64 byte aligned. |
| * The buffer returned from netdev_alloc_skb is |
| * aligned except if slab debugging is enabled. |
| */ |
| start = PTR_ALIGN(skb->data, 8); |
| skb_reserve(skb, start - skb->data); |
| } else |
| skb_reserve(skb, NET_IP_ALIGN); |
| |
| for (i = 0; i < sky2->rx_nfrags; i++) { |
| struct page *page = alloc_page(GFP_ATOMIC); |
| |
| if (!page) |
| goto free_partial; |
| skb_fill_page_desc(skb, i, page, 0, PAGE_SIZE); |
| } |
| |
| return skb; |
| free_partial: |
| kfree_skb(skb); |
| nomem: |
| return NULL; |
| } |
| |
| static inline void sky2_rx_update(struct sky2_port *sky2, unsigned rxq) |
| { |
| sky2_put_idx(sky2->hw, rxq, sky2->rx_put); |
| } |
| |
| /* |
| * Allocate and setup receiver buffer pool. |
| * Normal case this ends up creating one list element for skb |
| * in the receive ring. Worst case if using large MTU and each |
| * allocation falls on a different 64 bit region, that results |
| * in 6 list elements per ring entry. |
| * One element is used for checksum enable/disable, and one |
| * extra to avoid wrap. |
| */ |
| static int sky2_rx_start(struct sky2_port *sky2) |
| { |
| struct sky2_hw *hw = sky2->hw; |
| struct rx_ring_info *re; |
| unsigned rxq = rxqaddr[sky2->port]; |
| unsigned i, size, thresh; |
| |
| sky2->rx_put = sky2->rx_next = 0; |
| sky2_qset(hw, rxq); |
| |
| /* On PCI express lowering the watermark gives better performance */ |
| if (pci_find_capability(hw->pdev, PCI_CAP_ID_EXP)) |
| sky2_write32(hw, Q_ADDR(rxq, Q_WM), BMU_WM_PEX); |
| |
| /* These chips have no ram buffer? |
| * MAC Rx RAM Read is controlled by hardware */ |
| if (hw->chip_id == CHIP_ID_YUKON_EC_U && |
| (hw->chip_rev == CHIP_REV_YU_EC_U_A1 |
| || hw->chip_rev == CHIP_REV_YU_EC_U_B0)) |
| sky2_write32(hw, Q_ADDR(rxq, Q_TEST), F_M_RX_RAM_DIS); |
| |
| sky2_prefetch_init(hw, rxq, sky2->rx_le_map, RX_LE_SIZE - 1); |
| |
| if (!(hw->flags & SKY2_HW_NEW_LE)) |
| rx_set_checksum(sky2); |
| |
| /* Space needed for frame data + headers rounded up */ |
| size = roundup(sky2->netdev->mtu + ETH_HLEN + VLAN_HLEN, 8); |
| |
| /* Stopping point for hardware truncation */ |
| thresh = (size - 8) / sizeof(u32); |
| |
| sky2->rx_nfrags = size >> PAGE_SHIFT; |
| BUG_ON(sky2->rx_nfrags > ARRAY_SIZE(re->frag_addr)); |
| |
| /* Compute residue after pages */ |
| size -= sky2->rx_nfrags << PAGE_SHIFT; |
| |
| /* Optimize to handle small packets and headers */ |
| if (size < copybreak) |
| size = copybreak; |
| if (size < ETH_HLEN) |
| size = ETH_HLEN; |
| |
| sky2->rx_data_size = size; |
| |
| /* Fill Rx ring */ |
| for (i = 0; i < sky2->rx_pending; i++) { |
| re = sky2->rx_ring + i; |
| |
| re->skb = sky2_rx_alloc(sky2); |
| if (!re->skb) |
| goto nomem; |
| |
| if (sky2_rx_map_skb(hw->pdev, re, sky2->rx_data_size)) { |
| dev_kfree_skb(re->skb); |
| re->skb = NULL; |
| goto nomem; |
| } |
| |
| sky2_rx_submit(sky2, re); |
| } |
| |
| /* |
| * The receiver hangs if it receives frames larger than the |
| * packet buffer. As a workaround, truncate oversize frames, but |
| * the register is limited to 9 bits, so if you do frames > 2052 |
| * you better get the MTU right! |
| */ |
| if (thresh > 0x1ff) |
| sky2_write32(hw, SK_REG(sky2->port, RX_GMF_CTRL_T), RX_TRUNC_OFF); |
| else { |
| sky2_write16(hw, SK_REG(sky2->port, RX_GMF_TR_THR), thresh); |
| sky2_write32(hw, SK_REG(sky2->port, RX_GMF_CTRL_T), RX_TRUNC_ON); |
| } |
| |
| /* Tell chip about available buffers */ |
| sky2_rx_update(sky2, rxq); |
| return 0; |
| nomem: |
| sky2_rx_clean(sky2); |
| return -ENOMEM; |
| } |
| |
| static int sky2_alloc_buffers(struct sky2_port *sky2) |
| { |
| struct sky2_hw *hw = sky2->hw; |
| |
| /* must be power of 2 */ |
| sky2->tx_le = pci_alloc_consistent(hw->pdev, |
| sky2->tx_ring_size * |
| sizeof(struct sky2_tx_le), |
| &sky2->tx_le_map); |
| if (!sky2->tx_le) |
| goto nomem; |
| |
| sky2->tx_ring = kcalloc(sky2->tx_ring_size, sizeof(struct tx_ring_info), |
| GFP_KERNEL); |
| if (!sky2->tx_ring) |
| goto nomem; |
| |
| sky2->rx_le = pci_alloc_consistent(hw->pdev, RX_LE_BYTES, |
| &sky2->rx_le_map); |
| if (!sky2->rx_le) |
| goto nomem; |
| memset(sky2->rx_le, 0, RX_LE_BYTES); |
| |
| sky2->rx_ring = kcalloc(sky2->rx_pending, sizeof(struct rx_ring_info), |
| GFP_KERNEL); |
| if (!sky2->rx_ring) |
| goto nomem; |
| |
| return 0; |
| nomem: |
| return -ENOMEM; |
| } |
| |
| static void sky2_free_buffers(struct sky2_port *sky2) |
| { |
| struct sky2_hw *hw = sky2->hw; |
| |
| if (sky2->rx_le) { |
| pci_free_consistent(hw->pdev, RX_LE_BYTES, |
| sky2->rx_le, sky2->rx_le_map); |
| sky2->rx_le = NULL; |
| } |
| if (sky2->tx_le) { |
| pci_free_consistent(hw->pdev, |
| sky2->tx_ring_size * sizeof(struct sky2_tx_le), |
| sky2->tx_le, sky2->tx_le_map); |
| sky2->tx_le = NULL; |
| } |
| kfree(sky2->tx_ring); |
| kfree(sky2->rx_ring); |
| |
| sky2->tx_ring = NULL; |
| sky2->rx_ring = NULL; |
| } |
| |
| /* Bring up network interface. */ |
| static int sky2_up(struct net_device *dev) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| struct sky2_hw *hw = sky2->hw; |
| unsigned port = sky2->port; |
| u32 imask, ramsize; |
| int cap, err; |
| struct net_device *otherdev = hw->dev[sky2->port^1]; |
| |
| /* |
| * On dual port PCI-X card, there is an problem where status |
| * can be received out of order due to split transactions |
| */ |
| if (otherdev && netif_running(otherdev) && |
| (cap = pci_find_capability(hw->pdev, PCI_CAP_ID_PCIX))) { |
| u16 cmd; |
| |
| cmd = sky2_pci_read16(hw, cap + PCI_X_CMD); |
| cmd &= ~PCI_X_CMD_MAX_SPLIT; |
| sky2_pci_write16(hw, cap + PCI_X_CMD, cmd); |
| |
| } |
| |
| netif_carrier_off(dev); |
| |
| err = sky2_alloc_buffers(sky2); |
| if (err) |
| goto err_out; |
| |
| tx_init(sky2); |
| |
| sky2_mac_init(hw, port); |
| |
| /* Register is number of 4K blocks on internal RAM buffer. */ |
| ramsize = sky2_read8(hw, B2_E_0) * 4; |
| if (ramsize > 0) { |
| u32 rxspace; |
| |
| pr_debug(PFX "%s: ram buffer %dK\n", dev->name, ramsize); |
| if (ramsize < 16) |
| rxspace = ramsize / 2; |
| else |
| rxspace = 8 + (2*(ramsize - 16))/3; |
| |
| sky2_ramset(hw, rxqaddr[port], 0, rxspace); |
| sky2_ramset(hw, txqaddr[port], rxspace, ramsize - rxspace); |
| |
| /* Make sure SyncQ is disabled */ |
| sky2_write8(hw, RB_ADDR(port == 0 ? Q_XS1 : Q_XS2, RB_CTRL), |
| RB_RST_SET); |
| } |
| |
| sky2_qset(hw, txqaddr[port]); |
| |
| /* This is copied from sk98lin 10.0.5.3; no one tells me about erratta's */ |
| if (hw->chip_id == CHIP_ID_YUKON_EX && hw->chip_rev == CHIP_REV_YU_EX_B0) |
| sky2_write32(hw, Q_ADDR(txqaddr[port], Q_TEST), F_TX_CHK_AUTO_OFF); |
| |
| /* Set almost empty threshold */ |
| if (hw->chip_id == CHIP_ID_YUKON_EC_U |
| && hw->chip_rev == CHIP_REV_YU_EC_U_A0) |
| sky2_write16(hw, Q_ADDR(txqaddr[port], Q_AL), ECU_TXFF_LEV); |
| |
| sky2_prefetch_init(hw, txqaddr[port], sky2->tx_le_map, |
| sky2->tx_ring_size - 1); |
| |
| #ifdef SKY2_VLAN_TAG_USED |
| sky2_set_vlan_mode(hw, port, sky2->vlgrp != NULL); |
| #endif |
| |
| err = sky2_rx_start(sky2); |
| if (err) |
| goto err_out; |
| |
| /* Enable interrupts from phy/mac for port */ |
| imask = sky2_read32(hw, B0_IMSK); |
| imask |= portirq_msk[port]; |
| sky2_write32(hw, B0_IMSK, imask); |
| sky2_read32(hw, B0_IMSK); |
| |
| if (netif_msg_ifup(sky2)) |
| printk(KERN_INFO PFX "%s: enabling interface\n", dev->name); |
| |
| return 0; |
| |
| err_out: |
| sky2_free_buffers(sky2); |
| return err; |
| } |
| |
| /* Modular subtraction in ring */ |
| static inline int tx_inuse(const struct sky2_port *sky2) |
| { |
| return (sky2->tx_prod - sky2->tx_cons) & (sky2->tx_ring_size - 1); |
| } |
| |
| /* Number of list elements available for next tx */ |
| static inline int tx_avail(const struct sky2_port *sky2) |
| { |
| return sky2->tx_pending - tx_inuse(sky2); |
| } |
| |
| /* Estimate of number of transmit list elements required */ |
| static unsigned tx_le_req(const struct sk_buff *skb) |
| { |
| unsigned count; |
| |
| count = (skb_shinfo(skb)->nr_frags + 1) |
| * (sizeof(dma_addr_t) / sizeof(u32)); |
| |
| if (skb_is_gso(skb)) |
| ++count; |
| else if (sizeof(dma_addr_t) == sizeof(u32)) |
| ++count; /* possible vlan */ |
| |
| if (skb->ip_summed == CHECKSUM_PARTIAL) |
| ++count; |
| |
| return count; |
| } |
| |
| static void sky2_tx_unmap(struct pci_dev *pdev, |
| const struct tx_ring_info *re) |
| { |
| if (re->flags & TX_MAP_SINGLE) |
| pci_unmap_single(pdev, pci_unmap_addr(re, mapaddr), |
| pci_unmap_len(re, maplen), |
| PCI_DMA_TODEVICE); |
| else if (re->flags & TX_MAP_PAGE) |
| pci_unmap_page(pdev, pci_unmap_addr(re, mapaddr), |
| pci_unmap_len(re, maplen), |
| PCI_DMA_TODEVICE); |
| } |
| |
| /* |
| * Put one packet in ring for transmit. |
| * A single packet can generate multiple list elements, and |
| * the number of ring elements will probably be less than the number |
| * of list elements used. |
| */ |
| static netdev_tx_t sky2_xmit_frame(struct sk_buff *skb, |
| struct net_device *dev) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| struct sky2_hw *hw = sky2->hw; |
| struct sky2_tx_le *le = NULL; |
| struct tx_ring_info *re; |
| unsigned i, len; |
| dma_addr_t mapping; |
| u32 upper; |
| u16 slot; |
| u16 mss; |
| u8 ctrl; |
| |
| if (unlikely(tx_avail(sky2) < tx_le_req(skb))) |
| return NETDEV_TX_BUSY; |
| |
| len = skb_headlen(skb); |
| mapping = pci_map_single(hw->pdev, skb->data, len, PCI_DMA_TODEVICE); |
| |
| if (pci_dma_mapping_error(hw->pdev, mapping)) |
| goto mapping_error; |
| |
| slot = sky2->tx_prod; |
| if (unlikely(netif_msg_tx_queued(sky2))) |
| printk(KERN_DEBUG "%s: tx queued, slot %u, len %d\n", |
| dev->name, slot, skb->len); |
| |
| /* Send high bits if needed */ |
| upper = upper_32_bits(mapping); |
| if (upper != sky2->tx_last_upper) { |
| le = get_tx_le(sky2, &slot); |
| le->addr = cpu_to_le32(upper); |
| sky2->tx_last_upper = upper; |
| le->opcode = OP_ADDR64 | HW_OWNER; |
| } |
| |
| /* Check for TCP Segmentation Offload */ |
| mss = skb_shinfo(skb)->gso_size; |
| if (mss != 0) { |
| |
| if (!(hw->flags & SKY2_HW_NEW_LE)) |
| mss += ETH_HLEN + ip_hdrlen(skb) + tcp_hdrlen(skb); |
| |
| if (mss != sky2->tx_last_mss) { |
| le = get_tx_le(sky2, &slot); |
| le->addr = cpu_to_le32(mss); |
| |
| if (hw->flags & SKY2_HW_NEW_LE) |
| le->opcode = OP_MSS | HW_OWNER; |
| else |
| le->opcode = OP_LRGLEN | HW_OWNER; |
| sky2->tx_last_mss = mss; |
| } |
| } |
| |
| ctrl = 0; |
| #ifdef SKY2_VLAN_TAG_USED |
| /* Add VLAN tag, can piggyback on LRGLEN or ADDR64 */ |
| if (sky2->vlgrp && vlan_tx_tag_present(skb)) { |
| if (!le) { |
| le = get_tx_le(sky2, &slot); |
| le->addr = 0; |
| le->opcode = OP_VLAN|HW_OWNER; |
| } else |
| le->opcode |= OP_VLAN; |
| le->length = cpu_to_be16(vlan_tx_tag_get(skb)); |
| ctrl |= INS_VLAN; |
| } |
| #endif |
| |
| /* Handle TCP checksum offload */ |
| if (skb->ip_summed == CHECKSUM_PARTIAL) { |
| /* On Yukon EX (some versions) encoding change. */ |
| if (hw->flags & SKY2_HW_AUTO_TX_SUM) |
| ctrl |= CALSUM; /* auto checksum */ |
| else { |
| const unsigned offset = skb_transport_offset(skb); |
| u32 tcpsum; |
| |
| tcpsum = offset << 16; /* sum start */ |
| tcpsum |= offset + skb->csum_offset; /* sum write */ |
| |
| ctrl |= CALSUM | WR_SUM | INIT_SUM | LOCK_SUM; |
| if (ip_hdr(skb)->protocol == IPPROTO_UDP) |
| ctrl |= UDPTCP; |
| |
| if (tcpsum != sky2->tx_tcpsum) { |
| sky2->tx_tcpsum = tcpsum; |
| |
| le = get_tx_le(sky2, &slot); |
| le->addr = cpu_to_le32(tcpsum); |
| le->length = 0; /* initial checksum value */ |
| le->ctrl = 1; /* one packet */ |
| le->opcode = OP_TCPLISW | HW_OWNER; |
| } |
| } |
| } |
| |
| re = sky2->tx_ring + slot; |
| re->flags = TX_MAP_SINGLE; |
| pci_unmap_addr_set(re, mapaddr, mapping); |
| pci_unmap_len_set(re, maplen, len); |
| |
| le = get_tx_le(sky2, &slot); |
| le->addr = cpu_to_le32(lower_32_bits(mapping)); |
| le->length = cpu_to_le16(len); |
| le->ctrl = ctrl; |
| le->opcode = mss ? (OP_LARGESEND | HW_OWNER) : (OP_PACKET | HW_OWNER); |
| |
| |
| for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) { |
| const skb_frag_t *frag = &skb_shinfo(skb)->frags[i]; |
| |
| mapping = pci_map_page(hw->pdev, frag->page, frag->page_offset, |
| frag->size, PCI_DMA_TODEVICE); |
| |
| if (pci_dma_mapping_error(hw->pdev, mapping)) |
| goto mapping_unwind; |
| |
| upper = upper_32_bits(mapping); |
| if (upper != sky2->tx_last_upper) { |
| le = get_tx_le(sky2, &slot); |
| le->addr = cpu_to_le32(upper); |
| sky2->tx_last_upper = upper; |
| le->opcode = OP_ADDR64 | HW_OWNER; |
| } |
| |
| re = sky2->tx_ring + slot; |
| re->flags = TX_MAP_PAGE; |
| pci_unmap_addr_set(re, mapaddr, mapping); |
| pci_unmap_len_set(re, maplen, frag->size); |
| |
| le = get_tx_le(sky2, &slot); |
| le->addr = cpu_to_le32(lower_32_bits(mapping)); |
| le->length = cpu_to_le16(frag->size); |
| le->ctrl = ctrl; |
| le->opcode = OP_BUFFER | HW_OWNER; |
| } |
| |
| re->skb = skb; |
| le->ctrl |= EOP; |
| |
| sky2->tx_prod = slot; |
| |
| if (tx_avail(sky2) <= MAX_SKB_TX_LE) |
| netif_stop_queue(dev); |
| |
| sky2_put_idx(hw, txqaddr[sky2->port], sky2->tx_prod); |
| |
| return NETDEV_TX_OK; |
| |
| mapping_unwind: |
| for (i = sky2->tx_prod; i != slot; i = RING_NEXT(i, sky2->tx_ring_size)) { |
| re = sky2->tx_ring + i; |
| |
| sky2_tx_unmap(hw->pdev, re); |
| } |
| |
| mapping_error: |
| if (net_ratelimit()) |
| dev_warn(&hw->pdev->dev, "%s: tx mapping error\n", dev->name); |
| dev_kfree_skb(skb); |
| return NETDEV_TX_OK; |
| } |
| |
| /* |
| * Free ring elements from starting at tx_cons until "done" |
| * |
| * NB: |
| * 1. The hardware will tell us about partial completion of multi-part |
| * buffers so make sure not to free skb to early. |
| * 2. This may run in parallel start_xmit because the it only |
| * looks at the tail of the queue of FIFO (tx_cons), not |
| * the head (tx_prod) |
| */ |
| static void sky2_tx_complete(struct sky2_port *sky2, u16 done) |
| { |
| struct net_device *dev = sky2->netdev; |
| unsigned idx; |
| |
| BUG_ON(done >= sky2->tx_ring_size); |
| |
| for (idx = sky2->tx_cons; idx != done; |
| idx = RING_NEXT(idx, sky2->tx_ring_size)) { |
| struct tx_ring_info *re = sky2->tx_ring + idx; |
| struct sk_buff *skb = re->skb; |
| |
| sky2_tx_unmap(sky2->hw->pdev, re); |
| |
| if (skb) { |
| if (unlikely(netif_msg_tx_done(sky2))) |
| printk(KERN_DEBUG "%s: tx done %u\n", |
| dev->name, idx); |
| |
| dev->stats.tx_packets++; |
| dev->stats.tx_bytes += skb->len; |
| |
| dev_kfree_skb_any(skb); |
| |
| sky2->tx_next = RING_NEXT(idx, sky2->tx_ring_size); |
| } |
| } |
| |
| sky2->tx_cons = idx; |
| smp_mb(); |
| |
| if (tx_avail(sky2) > MAX_SKB_TX_LE + 4) |
| netif_wake_queue(dev); |
| } |
| |
| static void sky2_tx_reset(struct sky2_hw *hw, unsigned port) |
| { |
| /* Disable Force Sync bit and Enable Alloc bit */ |
| sky2_write8(hw, SK_REG(port, TXA_CTRL), |
| TXA_DIS_FSYNC | TXA_DIS_ALLOC | TXA_STOP_RC); |
| |
| /* Stop Interval Timer and Limit Counter of Tx Arbiter */ |
| sky2_write32(hw, SK_REG(port, TXA_ITI_INI), 0L); |
| sky2_write32(hw, SK_REG(port, TXA_LIM_INI), 0L); |
| |
| /* Reset the PCI FIFO of the async Tx queue */ |
| sky2_write32(hw, Q_ADDR(txqaddr[port], Q_CSR), |
| BMU_RST_SET | BMU_FIFO_RST); |
| |
| /* Reset the Tx prefetch units */ |
| sky2_write32(hw, Y2_QADDR(txqaddr[port], PREF_UNIT_CTRL), |
| PREF_UNIT_RST_SET); |
| |
| sky2_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL), RB_RST_SET); |
| sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_SET); |
| } |
| |
| /* Network shutdown */ |
| static int sky2_down(struct net_device *dev) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| struct sky2_hw *hw = sky2->hw; |
| unsigned port = sky2->port; |
| u16 ctrl; |
| u32 imask; |
| |
| /* Never really got started! */ |
| if (!sky2->tx_le) |
| return 0; |
| |
| if (netif_msg_ifdown(sky2)) |
| printk(KERN_INFO PFX "%s: disabling interface\n", dev->name); |
| |
| /* Force flow control off */ |
| sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF); |
| |
| /* Stop transmitter */ |
| sky2_write32(hw, Q_ADDR(txqaddr[port], Q_CSR), BMU_STOP); |
| sky2_read32(hw, Q_ADDR(txqaddr[port], Q_CSR)); |
| |
| sky2_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL), |
| RB_RST_SET | RB_DIS_OP_MD); |
| |
| ctrl = gma_read16(hw, port, GM_GP_CTRL); |
| ctrl &= ~(GM_GPCR_TX_ENA | GM_GPCR_RX_ENA); |
| gma_write16(hw, port, GM_GP_CTRL, ctrl); |
| |
| sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET); |
| |
| /* Workaround shared GMAC reset */ |
| if (!(hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0 |
| && port == 0 && hw->dev[1] && netif_running(hw->dev[1]))) |
| sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_SET); |
| |
| sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET); |
| |
| /* Force any delayed status interrrupt and NAPI */ |
| sky2_write32(hw, STAT_LEV_TIMER_CNT, 0); |
| sky2_write32(hw, STAT_TX_TIMER_CNT, 0); |
| sky2_write32(hw, STAT_ISR_TIMER_CNT, 0); |
| sky2_read8(hw, STAT_ISR_TIMER_CTRL); |
| |
| sky2_rx_stop(sky2); |
| |
| /* Disable port IRQ */ |
| imask = sky2_read32(hw, B0_IMSK); |
| imask &= ~portirq_msk[port]; |
| sky2_write32(hw, B0_IMSK, imask); |
| sky2_read32(hw, B0_IMSK); |
| |
| synchronize_irq(hw->pdev->irq); |
| napi_synchronize(&hw->napi); |
| |
| spin_lock_bh(&sky2->phy_lock); |
| sky2_phy_power_down(hw, port); |
| spin_unlock_bh(&sky2->phy_lock); |
| |
| sky2_tx_reset(hw, port); |
| |
| /* Free any pending frames stuck in HW queue */ |
| sky2_tx_complete(sky2, sky2->tx_prod); |
| |
| sky2_rx_clean(sky2); |
| |
| sky2_free_buffers(sky2); |
| |
| return 0; |
| } |
| |
| static u16 sky2_phy_speed(const struct sky2_hw *hw, u16 aux) |
| { |
| if (hw->flags & SKY2_HW_FIBRE_PHY) |
| return SPEED_1000; |
| |
| if (!(hw->flags & SKY2_HW_GIGABIT)) { |
| if (aux & PHY_M_PS_SPEED_100) |
| return SPEED_100; |
| else |
| return SPEED_10; |
| } |
| |
| switch (aux & PHY_M_PS_SPEED_MSK) { |
| case PHY_M_PS_SPEED_1000: |
| return SPEED_1000; |
| case PHY_M_PS_SPEED_100: |
| return SPEED_100; |
| default: |
| return SPEED_10; |
| } |
| } |
| |
| static void sky2_link_up(struct sky2_port *sky2) |
| { |
| struct sky2_hw *hw = sky2->hw; |
| unsigned port = sky2->port; |
| u16 reg; |
| static const char *fc_name[] = { |
| [FC_NONE] = "none", |
| [FC_TX] = "tx", |
| [FC_RX] = "rx", |
| [FC_BOTH] = "both", |
| }; |
| |
| /* enable Rx/Tx */ |
| reg = gma_read16(hw, port, GM_GP_CTRL); |
| reg |= GM_GPCR_RX_ENA | GM_GPCR_TX_ENA; |
| gma_write16(hw, port, GM_GP_CTRL, reg); |
| |
| gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK); |
| |
| netif_carrier_on(sky2->netdev); |
| |
| mod_timer(&hw->watchdog_timer, jiffies + 1); |
| |
| /* Turn on link LED */ |
| sky2_write8(hw, SK_REG(port, LNK_LED_REG), |
| LINKLED_ON | LINKLED_BLINK_OFF | LINKLED_LINKSYNC_OFF); |
| |
| if (netif_msg_link(sky2)) |
| printk(KERN_INFO PFX |
| "%s: Link is up at %d Mbps, %s duplex, flow control %s\n", |
| sky2->netdev->name, sky2->speed, |
| sky2->duplex == DUPLEX_FULL ? "full" : "half", |
| fc_name[sky2->flow_status]); |
| } |
| |
| static void sky2_link_down(struct sky2_port *sky2) |
| { |
| struct sky2_hw *hw = sky2->hw; |
| unsigned port = sky2->port; |
| u16 reg; |
| |
| gm_phy_write(hw, port, PHY_MARV_INT_MASK, 0); |
| |
| reg = gma_read16(hw, port, GM_GP_CTRL); |
| reg &= ~(GM_GPCR_RX_ENA | GM_GPCR_TX_ENA); |
| gma_write16(hw, port, GM_GP_CTRL, reg); |
| |
| netif_carrier_off(sky2->netdev); |
| |
| /* Turn on link LED */ |
| sky2_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_OFF); |
| |
| if (netif_msg_link(sky2)) |
| printk(KERN_INFO PFX "%s: Link is down.\n", sky2->netdev->name); |
| |
| sky2_phy_init(hw, port); |
| } |
| |
| static enum flow_control sky2_flow(int rx, int tx) |
| { |
| if (rx) |
| return tx ? FC_BOTH : FC_RX; |
| else |
| return tx ? FC_TX : FC_NONE; |
| } |
| |
| static int sky2_autoneg_done(struct sky2_port *sky2, u16 aux) |
| { |
| struct sky2_hw *hw = sky2->hw; |
| unsigned port = sky2->port; |
| u16 advert, lpa; |
| |
| advert = gm_phy_read(hw, port, PHY_MARV_AUNE_ADV); |
| lpa = gm_phy_read(hw, port, PHY_MARV_AUNE_LP); |
| if (lpa & PHY_M_AN_RF) { |
| printk(KERN_ERR PFX "%s: remote fault", sky2->netdev->name); |
| return -1; |
| } |
| |
| if (!(aux & PHY_M_PS_SPDUP_RES)) { |
| printk(KERN_ERR PFX "%s: speed/duplex mismatch", |
| sky2->netdev->name); |
| return -1; |
| } |
| |
| sky2->speed = sky2_phy_speed(hw, aux); |
| sky2->duplex = (aux & PHY_M_PS_FULL_DUP) ? DUPLEX_FULL : DUPLEX_HALF; |
| |
| /* Since the pause result bits seem to in different positions on |
| * different chips. look at registers. |
| */ |
| if (hw->flags & SKY2_HW_FIBRE_PHY) { |
| /* Shift for bits in fiber PHY */ |
| advert &= ~(ADVERTISE_PAUSE_CAP|ADVERTISE_PAUSE_ASYM); |
| lpa &= ~(LPA_PAUSE_CAP|LPA_PAUSE_ASYM); |
| |
| if (advert & ADVERTISE_1000XPAUSE) |
| advert |= ADVERTISE_PAUSE_CAP; |
| if (advert & ADVERTISE_1000XPSE_ASYM) |
| advert |= ADVERTISE_PAUSE_ASYM; |
| if (lpa & LPA_1000XPAUSE) |
| lpa |= LPA_PAUSE_CAP; |
| if (lpa & LPA_1000XPAUSE_ASYM) |
| lpa |= LPA_PAUSE_ASYM; |
| } |
| |
| sky2->flow_status = FC_NONE; |
| if (advert & ADVERTISE_PAUSE_CAP) { |
| if (lpa & LPA_PAUSE_CAP) |
| sky2->flow_status = FC_BOTH; |
| else if (advert & ADVERTISE_PAUSE_ASYM) |
| sky2->flow_status = FC_RX; |
| } else if (advert & ADVERTISE_PAUSE_ASYM) { |
| if ((lpa & LPA_PAUSE_CAP) && (lpa & LPA_PAUSE_ASYM)) |
| sky2->flow_status = FC_TX; |
| } |
| |
| if (sky2->duplex == DUPLEX_HALF && sky2->speed < SPEED_1000 |
| && !(hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX)) |
| sky2->flow_status = FC_NONE; |
| |
| if (sky2->flow_status & FC_TX) |
| sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_ON); |
| else |
| sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF); |
| |
| return 0; |
| } |
| |
| /* Interrupt from PHY */ |
| static void sky2_phy_intr(struct sky2_hw *hw, unsigned port) |
| { |
| struct net_device *dev = hw->dev[port]; |
| struct sky2_port *sky2 = netdev_priv(dev); |
| u16 istatus, phystat; |
| |
| if (!netif_running(dev)) |
| return; |
| |
| spin_lock(&sky2->phy_lock); |
| istatus = gm_phy_read(hw, port, PHY_MARV_INT_STAT); |
| phystat = gm_phy_read(hw, port, PHY_MARV_PHY_STAT); |
| |
| if (netif_msg_intr(sky2)) |
| printk(KERN_INFO PFX "%s: phy interrupt status 0x%x 0x%x\n", |
| sky2->netdev->name, istatus, phystat); |
| |
| if (istatus & PHY_M_IS_AN_COMPL) { |
| if (sky2_autoneg_done(sky2, phystat) == 0) |
| sky2_link_up(sky2); |
| goto out; |
| } |
| |
| if (istatus & PHY_M_IS_LSP_CHANGE) |
| sky2->speed = sky2_phy_speed(hw, phystat); |
| |
| if (istatus & PHY_M_IS_DUP_CHANGE) |
| sky2->duplex = |
| (phystat & PHY_M_PS_FULL_DUP) ? DUPLEX_FULL : DUPLEX_HALF; |
| |
| if (istatus & PHY_M_IS_LST_CHANGE) { |
| if (phystat & PHY_M_PS_LINK_UP) |
| sky2_link_up(sky2); |
| else |
| sky2_link_down(sky2); |
| } |
| out: |
| spin_unlock(&sky2->phy_lock); |
| } |
| |
| /* Transmit timeout is only called if we are running, carrier is up |
| * and tx queue is full (stopped). |
| */ |
| static void sky2_tx_timeout(struct net_device *dev) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| struct sky2_hw *hw = sky2->hw; |
| |
| if (netif_msg_timer(sky2)) |
| printk(KERN_ERR PFX "%s: tx timeout\n", dev->name); |
| |
| printk(KERN_DEBUG PFX "%s: transmit ring %u .. %u report=%u done=%u\n", |
| dev->name, sky2->tx_cons, sky2->tx_prod, |
| sky2_read16(hw, sky2->port == 0 ? STAT_TXA1_RIDX : STAT_TXA2_RIDX), |
| sky2_read16(hw, Q_ADDR(txqaddr[sky2->port], Q_DONE))); |
| |
| /* can't restart safely under softirq */ |
| schedule_work(&hw->restart_work); |
| } |
| |
| static int sky2_change_mtu(struct net_device *dev, int new_mtu) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| struct sky2_hw *hw = sky2->hw; |
| unsigned port = sky2->port; |
| int err; |
| u16 ctl, mode; |
| u32 imask; |
| |
| if (new_mtu < ETH_ZLEN || new_mtu > ETH_JUMBO_MTU) |
| return -EINVAL; |
| |
| if (new_mtu > ETH_DATA_LEN && |
| (hw->chip_id == CHIP_ID_YUKON_FE || |
| hw->chip_id == CHIP_ID_YUKON_FE_P)) |
| return -EINVAL; |
| |
| if (!netif_running(dev)) { |
| dev->mtu = new_mtu; |
| return 0; |
| } |
| |
| imask = sky2_read32(hw, B0_IMSK); |
| sky2_write32(hw, B0_IMSK, 0); |
| |
| dev->trans_start = jiffies; /* prevent tx timeout */ |
| netif_stop_queue(dev); |
| napi_disable(&hw->napi); |
| |
| synchronize_irq(hw->pdev->irq); |
| |
| if (!(hw->flags & SKY2_HW_RAM_BUFFER)) |
| sky2_set_tx_stfwd(hw, port); |
| |
| ctl = gma_read16(hw, port, GM_GP_CTRL); |
| gma_write16(hw, port, GM_GP_CTRL, ctl & ~GM_GPCR_RX_ENA); |
| sky2_rx_stop(sky2); |
| sky2_rx_clean(sky2); |
| |
| dev->mtu = new_mtu; |
| |
| mode = DATA_BLIND_VAL(DATA_BLIND_DEF) | |
| GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF); |
| |
| if (dev->mtu > ETH_DATA_LEN) |
| mode |= GM_SMOD_JUMBO_ENA; |
| |
| gma_write16(hw, port, GM_SERIAL_MODE, mode); |
| |
| sky2_write8(hw, RB_ADDR(rxqaddr[port], RB_CTRL), RB_ENA_OP_MD); |
| |
| err = sky2_rx_start(sky2); |
| sky2_write32(hw, B0_IMSK, imask); |
| |
| sky2_read32(hw, B0_Y2_SP_LISR); |
| napi_enable(&hw->napi); |
| |
| if (err) |
| dev_close(dev); |
| else { |
| gma_write16(hw, port, GM_GP_CTRL, ctl); |
| |
| netif_wake_queue(dev); |
| } |
| |
| return err; |
| } |
| |
| /* For small just reuse existing skb for next receive */ |
| static struct sk_buff *receive_copy(struct sky2_port *sky2, |
| const struct rx_ring_info *re, |
| unsigned length) |
| { |
| struct sk_buff *skb; |
| |
| skb = netdev_alloc_skb_ip_align(sky2->netdev, length); |
| if (likely(skb)) { |
| pci_dma_sync_single_for_cpu(sky2->hw->pdev, re->data_addr, |
| length, PCI_DMA_FROMDEVICE); |
| skb_copy_from_linear_data(re->skb, skb->data, length); |
| skb->ip_summed = re->skb->ip_summed; |
| skb->csum = re->skb->csum; |
| pci_dma_sync_single_for_device(sky2->hw->pdev, re->data_addr, |
| length, PCI_DMA_FROMDEVICE); |
| re->skb->ip_summed = CHECKSUM_NONE; |
| skb_put(skb, length); |
| } |
| return skb; |
| } |
| |
| /* Adjust length of skb with fragments to match received data */ |
| static void skb_put_frags(struct sk_buff *skb, unsigned int hdr_space, |
| unsigned int length) |
| { |
| int i, num_frags; |
| unsigned int size; |
| |
| /* put header into skb */ |
| size = min(length, hdr_space); |
| skb->tail += size; |
| skb->len += size; |
| length -= size; |
| |
| num_frags = skb_shinfo(skb)->nr_frags; |
| for (i = 0; i < num_frags; i++) { |
| skb_frag_t *frag = &skb_shinfo(skb)->frags[i]; |
| |
| if (length == 0) { |
| /* don't need this page */ |
| __free_page(frag->page); |
| --skb_shinfo(skb)->nr_frags; |
| } else { |
| size = min(length, (unsigned) PAGE_SIZE); |
| |
| frag->size = size; |
| skb->data_len += size; |
| skb->truesize += size; |
| skb->len += size; |
| length -= size; |
| } |
| } |
| } |
| |
| /* Normal packet - take skb from ring element and put in a new one */ |
| static struct sk_buff *receive_new(struct sky2_port *sky2, |
| struct rx_ring_info *re, |
| unsigned int length) |
| { |
| struct sk_buff *skb, *nskb; |
| unsigned hdr_space = sky2->rx_data_size; |
| |
| /* Don't be tricky about reusing pages (yet) */ |
| nskb = sky2_rx_alloc(sky2); |
| if (unlikely(!nskb)) |
| return NULL; |
| |
| skb = re->skb; |
| sky2_rx_unmap_skb(sky2->hw->pdev, re); |
| |
| prefetch(skb->data); |
| re->skb = nskb; |
| if (sky2_rx_map_skb(sky2->hw->pdev, re, hdr_space)) { |
| dev_kfree_skb(nskb); |
| re->skb = skb; |
| return NULL; |
| } |
| |
| if (skb_shinfo(skb)->nr_frags) |
| skb_put_frags(skb, hdr_space, length); |
| else |
| skb_put(skb, length); |
| return skb; |
| } |
| |
| /* |
| * Receive one packet. |
| * For larger packets, get new buffer. |
| */ |
| static struct sk_buff *sky2_receive(struct net_device *dev, |
| u16 length, u32 status) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| struct rx_ring_info *re = sky2->rx_ring + sky2->rx_next; |
| struct sk_buff *skb = NULL; |
| u16 count = (status & GMR_FS_LEN) >> 16; |
| |
| #ifdef SKY2_VLAN_TAG_USED |
| /* Account for vlan tag */ |
| if (sky2->vlgrp && (status & GMR_FS_VLAN)) |
| count -= VLAN_HLEN; |
| #endif |
| |
| if (unlikely(netif_msg_rx_status(sky2))) |
| printk(KERN_DEBUG PFX "%s: rx slot %u status 0x%x len %d\n", |
| dev->name, sky2->rx_next, status, length); |
| |
| sky2->rx_next = (sky2->rx_next + 1) % sky2->rx_pending; |
| prefetch(sky2->rx_ring + sky2->rx_next); |
| |
| /* This chip has hardware problems that generates bogus status. |
| * So do only marginal checking and expect higher level protocols |
| * to handle crap frames. |
| */ |
| if (sky2->hw->chip_id == CHIP_ID_YUKON_FE_P && |
| sky2->hw->chip_rev == CHIP_REV_YU_FE2_A0 && |
| length != count) |
| goto okay; |
| |
| if (status & GMR_FS_ANY_ERR) |
| goto error; |
| |
| if (!(status & GMR_FS_RX_OK)) |
| goto resubmit; |
| |
| /* if length reported by DMA does not match PHY, packet was truncated */ |
| if (length != count) |
| goto len_error; |
| |
| okay: |
| if (length < copybreak) |
| skb = receive_copy(sky2, re, length); |
| else |
| skb = receive_new(sky2, re, length); |
| resubmit: |
| sky2_rx_submit(sky2, re); |
| |
| return skb; |
| |
| len_error: |
| /* Truncation of overlength packets |
| causes PHY length to not match MAC length */ |
| ++dev->stats.rx_length_errors; |
| if (netif_msg_rx_err(sky2) && net_ratelimit()) |
| pr_info(PFX "%s: rx length error: status %#x length %d\n", |
| dev->name, status, length); |
| goto resubmit; |
| |
| error: |
| ++dev->stats.rx_errors; |
| if (status & GMR_FS_RX_FF_OV) { |
| dev->stats.rx_over_errors++; |
| goto resubmit; |
| } |
| |
| if (netif_msg_rx_err(sky2) && net_ratelimit()) |
| printk(KERN_INFO PFX "%s: rx error, status 0x%x length %d\n", |
| dev->name, status, length); |
| |
| if (status & (GMR_FS_LONG_ERR | GMR_FS_UN_SIZE)) |
| dev->stats.rx_length_errors++; |
| if (status & GMR_FS_FRAGMENT) |
| dev->stats.rx_frame_errors++; |
| if (status & GMR_FS_CRC_ERR) |
| dev->stats.rx_crc_errors++; |
| |
| goto resubmit; |
| } |
| |
| /* Transmit complete */ |
| static inline void sky2_tx_done(struct net_device *dev, u16 last) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| |
| if (netif_running(dev)) |
| sky2_tx_complete(sky2, last); |
| } |
| |
| static inline void sky2_skb_rx(const struct sky2_port *sky2, |
| u32 status, struct sk_buff *skb) |
| { |
| #ifdef SKY2_VLAN_TAG_USED |
| u16 vlan_tag = be16_to_cpu(sky2->rx_tag); |
| if (sky2->vlgrp && (status & GMR_FS_VLAN)) { |
| if (skb->ip_summed == CHECKSUM_NONE) |
| vlan_hwaccel_receive_skb(skb, sky2->vlgrp, vlan_tag); |
| else |
| vlan_gro_receive(&sky2->hw->napi, sky2->vlgrp, |
| vlan_tag, skb); |
| return; |
| } |
| #endif |
| if (skb->ip_summed == CHECKSUM_NONE) |
| netif_receive_skb(skb); |
| else |
| napi_gro_receive(&sky2->hw->napi, skb); |
| } |
| |
| static inline void sky2_rx_done(struct sky2_hw *hw, unsigned port, |
| unsigned packets, unsigned bytes) |
| { |
| if (packets) { |
| struct net_device *dev = hw->dev[port]; |
| |
| dev->stats.rx_packets += packets; |
| dev->stats.rx_bytes += bytes; |
| dev->last_rx = jiffies; |
| sky2_rx_update(netdev_priv(dev), rxqaddr[port]); |
| } |
| } |
| |
| /* Process status response ring */ |
| static int sky2_status_intr(struct sky2_hw *hw, int to_do, u16 idx) |
| { |
| int work_done = 0; |
| unsigned int total_bytes[2] = { 0 }; |
| unsigned int total_packets[2] = { 0 }; |
| |
| rmb(); |
| do { |
| struct sky2_port *sky2; |
| struct sky2_status_le *le = hw->st_le + hw->st_idx; |
| unsigned port; |
| struct net_device *dev; |
| struct sk_buff *skb; |
| u32 status; |
| u16 length; |
| u8 opcode = le->opcode; |
| |
| if (!(opcode & HW_OWNER)) |
| break; |
| |
| hw->st_idx = RING_NEXT(hw->st_idx, STATUS_RING_SIZE); |
| |
| port = le->css & CSS_LINK_BIT; |
| dev = hw->dev[port]; |
| sky2 = netdev_priv(dev); |
| length = le16_to_cpu(le->length); |
| status = le32_to_cpu(le->status); |
| |
| le->opcode = 0; |
| switch (opcode & ~HW_OWNER) { |
| case OP_RXSTAT: |
| total_packets[port]++; |
| total_bytes[port] += length; |
| skb = sky2_receive(dev, length, status); |
| if (unlikely(!skb)) { |
| dev->stats.rx_dropped++; |
| break; |
| } |
| |
| /* This chip reports checksum status differently */ |
| if (hw->flags & SKY2_HW_NEW_LE) { |
| if ((sky2->flags & SKY2_FLAG_RX_CHECKSUM) && |
| (le->css & (CSS_ISIPV4 | CSS_ISIPV6)) && |
| (le->css & CSS_TCPUDPCSOK)) |
| skb->ip_summed = CHECKSUM_UNNECESSARY; |
| else |
| skb->ip_summed = CHECKSUM_NONE; |
| } |
| |
| skb->protocol = eth_type_trans(skb, dev); |
| |
| sky2_skb_rx(sky2, status, skb); |
| |
| /* Stop after net poll weight */ |
| if (++work_done >= to_do) |
| goto exit_loop; |
| break; |
| |
| #ifdef SKY2_VLAN_TAG_USED |
| case OP_RXVLAN: |
| sky2->rx_tag = length; |
| break; |
| |
| case OP_RXCHKSVLAN: |
| sky2->rx_tag = length; |
| /* fall through */ |
| #endif |
| case OP_RXCHKS: |
| if (!(sky2->flags & SKY2_FLAG_RX_CHECKSUM)) |
| break; |
| |
| /* If this happens then driver assuming wrong format */ |
| if (unlikely(hw->flags & SKY2_HW_NEW_LE)) { |
| if (net_ratelimit()) |
| printk(KERN_NOTICE "%s: unexpected" |
| " checksum status\n", |
| dev->name); |
| break; |
| } |
| |
| /* Both checksum counters are programmed to start at |
| * the same offset, so unless there is a problem they |
| * should match. This failure is an early indication that |
| * hardware receive checksumming won't work. |
| */ |
| if (likely(status >> 16 == (status & 0xffff))) { |
| skb = sky2->rx_ring[sky2->rx_next].skb; |
| skb->ip_summed = CHECKSUM_COMPLETE; |
| skb->csum = le16_to_cpu(status); |
| } else { |
| printk(KERN_NOTICE PFX "%s: hardware receive " |
| "checksum problem (status = %#x)\n", |
| dev->name, status); |
| sky2->flags &= ~SKY2_FLAG_RX_CHECKSUM; |
| |
| sky2_write32(sky2->hw, |
| Q_ADDR(rxqaddr[port], Q_CSR), |
| BMU_DIS_RX_CHKSUM); |
| } |
| break; |
| |
| case OP_TXINDEXLE: |
| /* TX index reports status for both ports */ |
| sky2_tx_done(hw->dev[0], status & 0xfff); |
| if (hw->dev[1]) |
| sky2_tx_done(hw->dev[1], |
| ((status >> 24) & 0xff) |
| | (u16)(length & 0xf) << 8); |
| break; |
| |
| default: |
| if (net_ratelimit()) |
| printk(KERN_WARNING PFX |
| "unknown status opcode 0x%x\n", opcode); |
| } |
| } while (hw->st_idx != idx); |
| |
| /* Fully processed status ring so clear irq */ |
| sky2_write32(hw, STAT_CTRL, SC_STAT_CLR_IRQ); |
| |
| exit_loop: |
| sky2_rx_done(hw, 0, total_packets[0], total_bytes[0]); |
| sky2_rx_done(hw, 1, total_packets[1], total_bytes[1]); |
| |
| return work_done; |
| } |
| |
| static void sky2_hw_error(struct sky2_hw *hw, unsigned port, u32 status) |
| { |
| struct net_device *dev = hw->dev[port]; |
| |
| if (net_ratelimit()) |
| printk(KERN_INFO PFX "%s: hw error interrupt status 0x%x\n", |
| dev->name, status); |
| |
| if (status & Y2_IS_PAR_RD1) { |
| if (net_ratelimit()) |
| printk(KERN_ERR PFX "%s: ram data read parity error\n", |
| dev->name); |
| /* Clear IRQ */ |
| sky2_write16(hw, RAM_BUFFER(port, B3_RI_CTRL), RI_CLR_RD_PERR); |
| } |
| |
| if (status & Y2_IS_PAR_WR1) { |
| if (net_ratelimit()) |
| printk(KERN_ERR PFX "%s: ram data write parity error\n", |
| dev->name); |
| |
| sky2_write16(hw, RAM_BUFFER(port, B3_RI_CTRL), RI_CLR_WR_PERR); |
| } |
| |
| if (status & Y2_IS_PAR_MAC1) { |
| if (net_ratelimit()) |
| printk(KERN_ERR PFX "%s: MAC parity error\n", dev->name); |
| sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_CLI_TX_PE); |
| } |
| |
| if (status & Y2_IS_PAR_RX1) { |
| if (net_ratelimit()) |
| printk(KERN_ERR PFX "%s: RX parity error\n", dev->name); |
| sky2_write32(hw, Q_ADDR(rxqaddr[port], Q_CSR), BMU_CLR_IRQ_PAR); |
| } |
| |
| if (status & Y2_IS_TCP_TXA1) { |
| if (net_ratelimit()) |
| printk(KERN_ERR PFX "%s: TCP segmentation error\n", |
| dev->name); |
| sky2_write32(hw, Q_ADDR(txqaddr[port], Q_CSR), BMU_CLR_IRQ_TCP); |
| } |
| } |
| |
| static void sky2_hw_intr(struct sky2_hw *hw) |
| { |
| struct pci_dev *pdev = hw->pdev; |
| u32 status = sky2_read32(hw, B0_HWE_ISRC); |
| u32 hwmsk = sky2_read32(hw, B0_HWE_IMSK); |
| |
| status &= hwmsk; |
| |
| if (status & Y2_IS_TIST_OV) |
| sky2_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_CLR_IRQ); |
| |
| if (status & (Y2_IS_MST_ERR | Y2_IS_IRQ_STAT)) { |
| u16 pci_err; |
| |
| sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON); |
| pci_err = sky2_pci_read16(hw, PCI_STATUS); |
| if (net_ratelimit()) |
| dev_err(&pdev->dev, "PCI hardware error (0x%x)\n", |
| pci_err); |
| |
| sky2_pci_write16(hw, PCI_STATUS, |
| pci_err | PCI_STATUS_ERROR_BITS); |
| sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF); |
| } |
| |
| if (status & Y2_IS_PCI_EXP) { |
| /* PCI-Express uncorrectable Error occurred */ |
| u32 err; |
| |
| sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON); |
| err = sky2_read32(hw, Y2_CFG_AER + PCI_ERR_UNCOR_STATUS); |
| sky2_write32(hw, Y2_CFG_AER + PCI_ERR_UNCOR_STATUS, |
| 0xfffffffful); |
| if (net_ratelimit()) |
| dev_err(&pdev->dev, "PCI Express error (0x%x)\n", err); |
| |
| sky2_read32(hw, Y2_CFG_AER + PCI_ERR_UNCOR_STATUS); |
| sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF); |
| } |
| |
| if (status & Y2_HWE_L1_MASK) |
| sky2_hw_error(hw, 0, status); |
| status >>= 8; |
| if (status & Y2_HWE_L1_MASK) |
| sky2_hw_error(hw, 1, status); |
| } |
| |
| static void sky2_mac_intr(struct sky2_hw *hw, unsigned port) |
| { |
| struct net_device *dev = hw->dev[port]; |
| struct sky2_port *sky2 = netdev_priv(dev); |
| u8 status = sky2_read8(hw, SK_REG(port, GMAC_IRQ_SRC)); |
| |
| if (netif_msg_intr(sky2)) |
| printk(KERN_INFO PFX "%s: mac interrupt status 0x%x\n", |
| dev->name, status); |
| |
| if (status & GM_IS_RX_CO_OV) |
| gma_read16(hw, port, GM_RX_IRQ_SRC); |
| |
| if (status & GM_IS_TX_CO_OV) |
| gma_read16(hw, port, GM_TX_IRQ_SRC); |
| |
| if (status & GM_IS_RX_FF_OR) { |
| ++dev->stats.rx_fifo_errors; |
| sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_CLI_RX_FO); |
| } |
| |
| if (status & GM_IS_TX_FF_UR) { |
| ++dev->stats.tx_fifo_errors; |
| sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_CLI_TX_FU); |
| } |
| } |
| |
| /* This should never happen it is a bug. */ |
| static void sky2_le_error(struct sky2_hw *hw, unsigned port, u16 q) |
| { |
| struct net_device *dev = hw->dev[port]; |
| u16 idx = sky2_read16(hw, Y2_QADDR(q, PREF_UNIT_GET_IDX)); |
| |
| dev_err(&hw->pdev->dev, PFX |
| "%s: descriptor error q=%#x get=%u put=%u\n", |
| dev->name, (unsigned) q, (unsigned) idx, |
| (unsigned) sky2_read16(hw, Y2_QADDR(q, PREF_UNIT_PUT_IDX))); |
| |
| sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_CLR_IRQ_CHK); |
| } |
| |
| static int sky2_rx_hung(struct net_device *dev) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| struct sky2_hw *hw = sky2->hw; |
| unsigned port = sky2->port; |
| unsigned rxq = rxqaddr[port]; |
| u32 mac_rp = sky2_read32(hw, SK_REG(port, RX_GMF_RP)); |
| u8 mac_lev = sky2_read8(hw, SK_REG(port, RX_GMF_RLEV)); |
| u8 fifo_rp = sky2_read8(hw, Q_ADDR(rxq, Q_RP)); |
| u8 fifo_lev = sky2_read8(hw, Q_ADDR(rxq, Q_RL)); |
| |
| /* If idle and MAC or PCI is stuck */ |
| if (sky2->check.last == dev->last_rx && |
| ((mac_rp == sky2->check.mac_rp && |
| mac_lev != 0 && mac_lev >= sky2->check.mac_lev) || |
| /* Check if the PCI RX hang */ |
| (fifo_rp == sky2->check.fifo_rp && |
| fifo_lev != 0 && fifo_lev >= sky2->check.fifo_lev))) { |
| printk(KERN_DEBUG PFX "%s: hung mac %d:%d fifo %d (%d:%d)\n", |
| dev->name, mac_lev, mac_rp, fifo_lev, fifo_rp, |
| sky2_read8(hw, Q_ADDR(rxq, Q_WP))); |
| return 1; |
| } else { |
| sky2->check.last = dev->last_rx; |
| sky2->check.mac_rp = mac_rp; |
| sky2->check.mac_lev = mac_lev; |
| sky2->check.fifo_rp = fifo_rp; |
| sky2->check.fifo_lev = fifo_lev; |
| return 0; |
| } |
| } |
| |
| static void sky2_watchdog(unsigned long arg) |
| { |
| struct sky2_hw *hw = (struct sky2_hw *) arg; |
| |
| /* Check for lost IRQ once a second */ |
| if (sky2_read32(hw, B0_ISRC)) { |
| napi_schedule(&hw->napi); |
| } else { |
| int i, active = 0; |
| |
| for (i = 0; i < hw->ports; i++) { |
| struct net_device *dev = hw->dev[i]; |
| if (!netif_running(dev)) |
| continue; |
| ++active; |
| |
| /* For chips with Rx FIFO, check if stuck */ |
| if ((hw->flags & SKY2_HW_RAM_BUFFER) && |
| sky2_rx_hung(dev)) { |
| pr_info(PFX "%s: receiver hang detected\n", |
| dev->name); |
| schedule_work(&hw->restart_work); |
| return; |
| } |
| } |
| |
| if (active == 0) |
| return; |
| } |
| |
| mod_timer(&hw->watchdog_timer, round_jiffies(jiffies + HZ)); |
| } |
| |
| /* Hardware/software error handling */ |
| static void sky2_err_intr(struct sky2_hw *hw, u32 status) |
| { |
| if (net_ratelimit()) |
| dev_warn(&hw->pdev->dev, "error interrupt status=%#x\n", status); |
| |
| if (status & Y2_IS_HW_ERR) |
| sky2_hw_intr(hw); |
| |
| if (status & Y2_IS_IRQ_MAC1) |
| sky2_mac_intr(hw, 0); |
| |
| if (status & Y2_IS_IRQ_MAC2) |
| sky2_mac_intr(hw, 1); |
| |
| if (status & Y2_IS_CHK_RX1) |
| sky2_le_error(hw, 0, Q_R1); |
| |
| if (status & Y2_IS_CHK_RX2) |
| sky2_le_error(hw, 1, Q_R2); |
| |
| if (status & Y2_IS_CHK_TXA1) |
| sky2_le_error(hw, 0, Q_XA1); |
| |
| if (status & Y2_IS_CHK_TXA2) |
| sky2_le_error(hw, 1, Q_XA2); |
| } |
| |
| static int sky2_poll(struct napi_struct *napi, int work_limit) |
| { |
| struct sky2_hw *hw = container_of(napi, struct sky2_hw, napi); |
| u32 status = sky2_read32(hw, B0_Y2_SP_EISR); |
| int work_done = 0; |
| u16 idx; |
| |
| if (unlikely(status & Y2_IS_ERROR)) |
| sky2_err_intr(hw, status); |
| |
| if (status & Y2_IS_IRQ_PHY1) |
| sky2_phy_intr(hw, 0); |
| |
| if (status & Y2_IS_IRQ_PHY2) |
| sky2_phy_intr(hw, 1); |
| |
| while ((idx = sky2_read16(hw, STAT_PUT_IDX)) != hw->st_idx) { |
| work_done += sky2_status_intr(hw, work_limit - work_done, idx); |
| |
| if (work_done >= work_limit) |
| goto done; |
| } |
| |
| napi_complete(napi); |
| sky2_read32(hw, B0_Y2_SP_LISR); |
| done: |
| |
| return work_done; |
| } |
| |
| static irqreturn_t sky2_intr(int irq, void *dev_id) |
| { |
| struct sky2_hw *hw = dev_id; |
| u32 status; |
| |
| /* Reading this mask interrupts as side effect */ |
| status = sky2_read32(hw, B0_Y2_SP_ISRC2); |
| if (status == 0 || status == ~0) |
| return IRQ_NONE; |
| |
| prefetch(&hw->st_le[hw->st_idx]); |
| |
| napi_schedule(&hw->napi); |
| |
| return IRQ_HANDLED; |
| } |
| |
| #ifdef CONFIG_NET_POLL_CONTROLLER |
| static void sky2_netpoll(struct net_device *dev) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| |
| napi_schedule(&sky2->hw->napi); |
| } |
| #endif |
| |
| /* Chip internal frequency for clock calculations */ |
| static u32 sky2_mhz(const struct sky2_hw *hw) |
| { |
| switch (hw->chip_id) { |
| case CHIP_ID_YUKON_EC: |
| case CHIP_ID_YUKON_EC_U: |
| case CHIP_ID_YUKON_EX: |
| case CHIP_ID_YUKON_SUPR: |
| case CHIP_ID_YUKON_UL_2: |
| return 125; |
| |
| case CHIP_ID_YUKON_FE: |
| return 100; |
| |
| case CHIP_ID_YUKON_FE_P: |
| return 50; |
| |
| case CHIP_ID_YUKON_XL: |
| return 156; |
| |
| default: |
| BUG(); |
| } |
| } |
| |
| static inline u32 sky2_us2clk(const struct sky2_hw *hw, u32 us) |
| { |
| return sky2_mhz(hw) * us; |
| } |
| |
| static inline u32 sky2_clk2us(const struct sky2_hw *hw, u32 clk) |
| { |
| return clk / sky2_mhz(hw); |
| } |
| |
| |
| static int __devinit sky2_init(struct sky2_hw *hw) |
| { |
| u8 t8; |
| |
| /* Enable all clocks and check for bad PCI access */ |
| sky2_pci_write32(hw, PCI_DEV_REG3, 0); |
| |
| sky2_write8(hw, B0_CTST, CS_RST_CLR); |
| |
| hw->chip_id = sky2_read8(hw, B2_CHIP_ID); |
| hw->chip_rev = (sky2_read8(hw, B2_MAC_CFG) & CFG_CHIP_R_MSK) >> 4; |
| |
| switch(hw->chip_id) { |
| case CHIP_ID_YUKON_XL: |
| hw->flags = SKY2_HW_GIGABIT | SKY2_HW_NEWER_PHY; |
| break; |
| |
| case CHIP_ID_YUKON_EC_U: |
| hw->flags = SKY2_HW_GIGABIT |
| | SKY2_HW_NEWER_PHY |
| | SKY2_HW_ADV_POWER_CTL; |
| break; |
| |
| case CHIP_ID_YUKON_EX: |
| hw->flags = SKY2_HW_GIGABIT |
| | SKY2_HW_NEWER_PHY |
| | SKY2_HW_NEW_LE |
| | SKY2_HW_ADV_POWER_CTL; |
| |
| /* New transmit checksum */ |
| if (hw->chip_rev != CHIP_REV_YU_EX_B0) |
| hw->flags |= SKY2_HW_AUTO_TX_SUM; |
| break; |
| |
| case CHIP_ID_YUKON_EC: |
| /* This rev is really old, and requires untested workarounds */ |
| if (hw->chip_rev == CHIP_REV_YU_EC_A1) { |
| dev_err(&hw->pdev->dev, "unsupported revision Yukon-EC rev A1\n"); |
| return -EOPNOTSUPP; |
| } |
| hw->flags = SKY2_HW_GIGABIT; |
| break; |
| |
| case CHIP_ID_YUKON_FE: |
| break; |
| |
| case CHIP_ID_YUKON_FE_P: |
| hw->flags = SKY2_HW_NEWER_PHY |
| | SKY2_HW_NEW_LE |
| | SKY2_HW_AUTO_TX_SUM |
| | SKY2_HW_ADV_POWER_CTL; |
| break; |
| |
| case CHIP_ID_YUKON_SUPR: |
| hw->flags = SKY2_HW_GIGABIT |
| | SKY2_HW_NEWER_PHY |
| | SKY2_HW_NEW_LE |
| | SKY2_HW_AUTO_TX_SUM |
| | SKY2_HW_ADV_POWER_CTL; |
| break; |
| |
| case CHIP_ID_YUKON_UL_2: |
| hw->flags = SKY2_HW_GIGABIT |
| | SKY2_HW_ADV_POWER_CTL; |
| break; |
| |
| default: |
| dev_err(&hw->pdev->dev, "unsupported chip type 0x%x\n", |
| hw->chip_id); |
| return -EOPNOTSUPP; |
| } |
| |
| hw->pmd_type = sky2_read8(hw, B2_PMD_TYP); |
| if (hw->pmd_type == 'L' || hw->pmd_type == 'S' || hw->pmd_type == 'P') |
| hw->flags |= SKY2_HW_FIBRE_PHY; |
| |
| hw->ports = 1; |
| t8 = sky2_read8(hw, B2_Y2_HW_RES); |
| if ((t8 & CFG_DUAL_MAC_MSK) == CFG_DUAL_MAC_MSK) { |
| if (!(sky2_read8(hw, B2_Y2_CLK_GATE) & Y2_STATUS_LNK2_INAC)) |
| ++hw->ports; |
| } |
| |
| if (sky2_read8(hw, B2_E_0)) |
| hw->flags |= SKY2_HW_RAM_BUFFER; |
| |
| return 0; |
| } |
| |
| static void sky2_reset(struct sky2_hw *hw) |
| { |
| struct pci_dev *pdev = hw->pdev; |
| u16 status; |
| int i, cap; |
| u32 hwe_mask = Y2_HWE_ALL_MASK; |
| |
| /* disable ASF */ |
| if (hw->chip_id == CHIP_ID_YUKON_EX) { |
| status = sky2_read16(hw, HCU_CCSR); |
| status &= ~(HCU_CCSR_AHB_RST | HCU_CCSR_CPU_RST_MODE | |
| HCU_CCSR_UC_STATE_MSK); |
| sky2_write16(hw, HCU_CCSR, status); |
| } else |
| sky2_write8(hw, B28_Y2_ASF_STAT_CMD, Y2_ASF_RESET); |
| sky2_write16(hw, B0_CTST, Y2_ASF_DISABLE); |
| |
| /* do a SW reset */ |
| sky2_write8(hw, B0_CTST, CS_RST_SET); |
| sky2_write8(hw, B0_CTST, CS_RST_CLR); |
| |
| /* allow writes to PCI config */ |
| sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON); |
| |
| /* clear PCI errors, if any */ |
| status = sky2_pci_read16(hw, PCI_STATUS); |
| status |= PCI_STATUS_ERROR_BITS; |
| sky2_pci_write16(hw, PCI_STATUS, status); |
| |
| sky2_write8(hw, B0_CTST, CS_MRST_CLR); |
| |
| cap = pci_find_capability(pdev, PCI_CAP_ID_EXP); |
| if (cap) { |
| sky2_write32(hw, Y2_CFG_AER + PCI_ERR_UNCOR_STATUS, |
| 0xfffffffful); |
| |
| /* If error bit is stuck on ignore it */ |
| if (sky2_read32(hw, B0_HWE_ISRC) & Y2_IS_PCI_EXP) |
| dev_info(&pdev->dev, "ignoring stuck error report bit\n"); |
| else |
| hwe_mask |= Y2_IS_PCI_EXP; |
| } |
| |
| sky2_power_on(hw); |
| sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF); |
| |
| for (i = 0; i < hw->ports; i++) { |
| sky2_write8(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_SET); |
| sky2_write8(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_CLR); |
| |
| if (hw->chip_id == CHIP_ID_YUKON_EX || |
| hw->chip_id == CHIP_ID_YUKON_SUPR) |
| sky2_write16(hw, SK_REG(i, GMAC_CTRL), |
| GMC_BYP_MACSECRX_ON | GMC_BYP_MACSECTX_ON |
| | GMC_BYP_RETR_ON); |
| } |
| |
| /* Clear I2C IRQ noise */ |
| sky2_write32(hw, B2_I2C_IRQ, 1); |
| |
| /* turn off hardware timer (unused) */ |
| sky2_write8(hw, B2_TI_CTRL, TIM_STOP); |
| sky2_write8(hw, B2_TI_CTRL, TIM_CLR_IRQ); |
| |
| /* Turn off descriptor polling */ |
| sky2_write32(hw, B28_DPT_CTRL, DPT_STOP); |
| |
| /* Turn off receive timestamp */ |
| sky2_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_STOP); |
| sky2_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_CLR_IRQ); |
| |
| /* enable the Tx Arbiters */ |
| for (i = 0; i < hw->ports; i++) |
| sky2_write8(hw, SK_REG(i, TXA_CTRL), TXA_ENA_ARB); |
| |
| /* Initialize ram interface */ |
| for (i = 0; i < hw->ports; i++) { |
| sky2_write8(hw, RAM_BUFFER(i, B3_RI_CTRL), RI_RST_CLR); |
| |
| sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_R1), SK_RI_TO_53); |
| sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XA1), SK_RI_TO_53); |
| sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XS1), SK_RI_TO_53); |
| sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_R1), SK_RI_TO_53); |
| sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XA1), SK_RI_TO_53); |
| sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XS1), SK_RI_TO_53); |
| sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_R2), SK_RI_TO_53); |
| sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XA2), SK_RI_TO_53); |
| sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XS2), SK_RI_TO_53); |
| sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_R2), SK_RI_TO_53); |
| sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XA2), SK_RI_TO_53); |
| sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XS2), SK_RI_TO_53); |
| } |
| |
| sky2_write32(hw, B0_HWE_IMSK, hwe_mask); |
| |
| for (i = 0; i < hw->ports; i++) |
| sky2_gmac_reset(hw, i); |
| |
| memset(hw->st_le, 0, STATUS_LE_BYTES); |
| hw->st_idx = 0; |
| |
| sky2_write32(hw, STAT_CTRL, SC_STAT_RST_SET); |
| sky2_write32(hw, STAT_CTRL, SC_STAT_RST_CLR); |
| |
| sky2_write32(hw, STAT_LIST_ADDR_LO, hw->st_dma); |
| sky2_write32(hw, STAT_LIST_ADDR_HI, (u64) hw->st_dma >> 32); |
| |
| /* Set the list last index */ |
| sky2_write16(hw, STAT_LAST_IDX, STATUS_RING_SIZE - 1); |
| |
| sky2_write16(hw, STAT_TX_IDX_TH, 10); |
| sky2_write8(hw, STAT_FIFO_WM, 16); |
| |
| /* set Status-FIFO ISR watermark */ |
| if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0) |
| sky2_write8(hw, STAT_FIFO_ISR_WM, 4); |
| else |
| sky2_write8(hw, STAT_FIFO_ISR_WM, 16); |
| |
| sky2_write32(hw, STAT_TX_TIMER_INI, sky2_us2clk(hw, 1000)); |
| sky2_write32(hw, STAT_ISR_TIMER_INI, sky2_us2clk(hw, 20)); |
| sky2_write32(hw, STAT_LEV_TIMER_INI, sky2_us2clk(hw, 100)); |
| |
| /* enable status unit */ |
| sky2_write32(hw, STAT_CTRL, SC_STAT_OP_ON); |
| |
| sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START); |
| sky2_write8(hw, STAT_LEV_TIMER_CTRL, TIM_START); |
| sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_START); |
| } |
| |
| /* Take device down (offline). |
| * Equivalent to doing dev_stop() but this does not |
| * inform upper layers of the transistion. |
| */ |
| static void sky2_detach(struct net_device *dev) |
| { |
| if (netif_running(dev)) { |
| netif_device_detach(dev); /* stop txq */ |
| sky2_down(dev); |
| } |
| } |
| |
| /* Bring device back after doing sky2_detach */ |
| static int sky2_reattach(struct net_device *dev) |
| { |
| int err = 0; |
| |
| if (netif_running(dev)) { |
| err = sky2_up(dev); |
| if (err) { |
| printk(KERN_INFO PFX "%s: could not restart %d\n", |
| dev->name, err); |
| dev_close(dev); |
| } else { |
| netif_device_attach(dev); |
| sky2_set_multicast(dev); |
| } |
| } |
| |
| return err; |
| } |
| |
| static void sky2_restart(struct work_struct *work) |
| { |
| struct sky2_hw *hw = container_of(work, struct sky2_hw, restart_work); |
| int i; |
| |
| rtnl_lock(); |
| for (i = 0; i < hw->ports; i++) |
| sky2_detach(hw->dev[i]); |
| |
| napi_disable(&hw->napi); |
| sky2_write32(hw, B0_IMSK, 0); |
| sky2_reset(hw); |
| sky2_write32(hw, B0_IMSK, Y2_IS_BASE); |
| napi_enable(&hw->napi); |
| |
| for (i = 0; i < hw->ports; i++) |
| sky2_reattach(hw->dev[i]); |
| |
| rtnl_unlock(); |
| } |
| |
| static inline u8 sky2_wol_supported(const struct sky2_hw *hw) |
| { |
| return sky2_is_copper(hw) ? (WAKE_PHY | WAKE_MAGIC) : 0; |
| } |
| |
| static void sky2_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol) |
| { |
| const struct sky2_port *sky2 = netdev_priv(dev); |
| |
| wol->supported = sky2_wol_supported(sky2->hw); |
| wol->wolopts = sky2->wol; |
| } |
| |
| static int sky2_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| struct sky2_hw *hw = sky2->hw; |
| |
| if ((wol->wolopts & ~sky2_wol_supported(sky2->hw)) |
| || !device_can_wakeup(&hw->pdev->dev)) |
| return -EOPNOTSUPP; |
| |
| sky2->wol = wol->wolopts; |
| |
| if (hw->chip_id == CHIP_ID_YUKON_EC_U || |
| hw->chip_id == CHIP_ID_YUKON_EX || |
| hw->chip_id == CHIP_ID_YUKON_FE_P) |
| sky2_write32(hw, B0_CTST, sky2->wol |
| ? Y2_HW_WOL_ON : Y2_HW_WOL_OFF); |
| |
| device_set_wakeup_enable(&hw->pdev->dev, sky2->wol); |
| |
| if (!netif_running(dev)) |
| sky2_wol_init(sky2); |
| return 0; |
| } |
| |
| static u32 sky2_supported_modes(const struct sky2_hw *hw) |
| { |
| if (sky2_is_copper(hw)) { |
| u32 modes = SUPPORTED_10baseT_Half |
| | SUPPORTED_10baseT_Full |
| | SUPPORTED_100baseT_Half |
| | SUPPORTED_100baseT_Full |
| | SUPPORTED_Autoneg | SUPPORTED_TP; |
| |
| if (hw->flags & SKY2_HW_GIGABIT) |
| modes |= SUPPORTED_1000baseT_Half |
| | SUPPORTED_1000baseT_Full; |
| return modes; |
| } else |
| return SUPPORTED_1000baseT_Half |
| | SUPPORTED_1000baseT_Full |
| | SUPPORTED_Autoneg |
| | SUPPORTED_FIBRE; |
| } |
| |
| static int sky2_get_settings(struct net_device *dev, struct ethtool_cmd *ecmd) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| struct sky2_hw *hw = sky2->hw; |
| |
| ecmd->transceiver = XCVR_INTERNAL; |
| ecmd->supported = sky2_supported_modes(hw); |
| ecmd->phy_address = PHY_ADDR_MARV; |
| if (sky2_is_copper(hw)) { |
| ecmd->port = PORT_TP; |
| ecmd->speed = sky2->speed; |
| } else { |
| ecmd->speed = SPEED_1000; |
| ecmd->port = PORT_FIBRE; |
| } |
| |
| ecmd->advertising = sky2->advertising; |
| ecmd->autoneg = (sky2->flags & SKY2_FLAG_AUTO_SPEED) |
| ? AUTONEG_ENABLE : AUTONEG_DISABLE; |
| ecmd->duplex = sky2->duplex; |
| return 0; |
| } |
| |
| static int sky2_set_settings(struct net_device *dev, struct ethtool_cmd *ecmd) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| const struct sky2_hw *hw = sky2->hw; |
| u32 supported = sky2_supported_modes(hw); |
| |
| if (ecmd->autoneg == AUTONEG_ENABLE) { |
| sky2->flags |= SKY2_FLAG_AUTO_SPEED; |
| ecmd->advertising = supported; |
| sky2->duplex = -1; |
| sky2->speed = -1; |
| } else { |
| u32 setting; |
| |
| switch (ecmd->speed) { |
| case SPEED_1000: |
| if (ecmd->duplex == DUPLEX_FULL) |
| setting = SUPPORTED_1000baseT_Full; |
| else if (ecmd->duplex == DUPLEX_HALF) |
| setting = SUPPORTED_1000baseT_Half; |
| else |
| return -EINVAL; |
| break; |
| case SPEED_100: |
| if (ecmd->duplex == DUPLEX_FULL) |
| setting = SUPPORTED_100baseT_Full; |
| else if (ecmd->duplex == DUPLEX_HALF) |
| setting = SUPPORTED_100baseT_Half; |
| else |
| return -EINVAL; |
| break; |
| |
| case SPEED_10: |
| if (ecmd->duplex == DUPLEX_FULL) |
| setting = SUPPORTED_10baseT_Full; |
| else if (ecmd->duplex == DUPLEX_HALF) |
| setting = SUPPORTED_10baseT_Half; |
| else |
| return -EINVAL; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| if ((setting & supported) == 0) |
| return -EINVAL; |
| |
| sky2->speed = ecmd->speed; |
| sky2->duplex = ecmd->duplex; |
| sky2->flags &= ~SKY2_FLAG_AUTO_SPEED; |
| } |
| |
| sky2->advertising = ecmd->advertising; |
| |
| if (netif_running(dev)) { |
| sky2_phy_reinit(sky2); |
| sky2_set_multicast(dev); |
| } |
| |
| return 0; |
| } |
| |
| static void sky2_get_drvinfo(struct net_device *dev, |
| struct ethtool_drvinfo *info) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| |
| strcpy(info->driver, DRV_NAME); |
| strcpy(info->version, DRV_VERSION); |
| strcpy(info->fw_version, "N/A"); |
| strcpy(info->bus_info, pci_name(sky2->hw->pdev)); |
| } |
| |
| static const struct sky2_stat { |
| char name[ETH_GSTRING_LEN]; |
| u16 offset; |
| } sky2_stats[] = { |
| { "tx_bytes", GM_TXO_OK_HI }, |
| { "rx_bytes", GM_RXO_OK_HI }, |
| { "tx_broadcast", GM_TXF_BC_OK }, |
| { "rx_broadcast", GM_RXF_BC_OK }, |
| { "tx_multicast", GM_TXF_MC_OK }, |
| { "rx_multicast", GM_RXF_MC_OK }, |
| { "tx_unicast", GM_TXF_UC_OK }, |
| { "rx_unicast", GM_RXF_UC_OK }, |
| { "tx_mac_pause", GM_TXF_MPAUSE }, |
| { "rx_mac_pause", GM_RXF_MPAUSE }, |
| { "collisions", GM_TXF_COL }, |
| { "late_collision",GM_TXF_LAT_COL }, |
| { "aborted", GM_TXF_ABO_COL }, |
| { "single_collisions", GM_TXF_SNG_COL }, |
| { "multi_collisions", GM_TXF_MUL_COL }, |
| |
| { "rx_short", GM_RXF_SHT }, |
| { "rx_runt", GM_RXE_FRAG }, |
| { "rx_64_byte_packets", GM_RXF_64B }, |
| { "rx_65_to_127_byte_packets", GM_RXF_127B }, |
| { "rx_128_to_255_byte_packets", GM_RXF_255B }, |
| { "rx_256_to_511_byte_packets", GM_RXF_511B }, |
| { "rx_512_to_1023_byte_packets", GM_RXF_1023B }, |
| { "rx_1024_to_1518_byte_packets", GM_RXF_1518B }, |
| { "rx_1518_to_max_byte_packets", GM_RXF_MAX_SZ }, |
| { "rx_too_long", GM_RXF_LNG_ERR }, |
| { "rx_fifo_overflow", GM_RXE_FIFO_OV }, |
| { "rx_jabber", GM_RXF_JAB_PKT }, |
| { "rx_fcs_error", GM_RXF_FCS_ERR }, |
| |
| { "tx_64_byte_packets", GM_TXF_64B }, |
| { "tx_65_to_127_byte_packets", GM_TXF_127B }, |
| { "tx_128_to_255_byte_packets", GM_TXF_255B }, |
| { "tx_256_to_511_byte_packets", GM_TXF_511B }, |
| { "tx_512_to_1023_byte_packets", GM_TXF_1023B }, |
| { "tx_1024_to_1518_byte_packets", GM_TXF_1518B }, |
| { "tx_1519_to_max_byte_packets", GM_TXF_MAX_SZ }, |
| { "tx_fifo_underrun", GM_TXE_FIFO_UR }, |
| }; |
| |
| static u32 sky2_get_rx_csum(struct net_device *dev) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| |
| return !!(sky2->flags & SKY2_FLAG_RX_CHECKSUM); |
| } |
| |
| static int sky2_set_rx_csum(struct net_device *dev, u32 data) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| |
| if (data) |
| sky2->flags |= SKY2_FLAG_RX_CHECKSUM; |
| else |
| sky2->flags &= ~SKY2_FLAG_RX_CHECKSUM; |
| |
| sky2_write32(sky2->hw, Q_ADDR(rxqaddr[sky2->port], Q_CSR), |
| data ? BMU_ENA_RX_CHKSUM : BMU_DIS_RX_CHKSUM); |
| |
| return 0; |
| } |
| |
| static u32 sky2_get_msglevel(struct net_device *netdev) |
| { |
| struct sky2_port *sky2 = netdev_priv(netdev); |
| return sky2->msg_enable; |
| } |
| |
| static int sky2_nway_reset(struct net_device *dev) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| |
| if (!netif_running(dev) || !(sky2->flags & SKY2_FLAG_AUTO_SPEED)) |
| return -EINVAL; |
| |
| sky2_phy_reinit(sky2); |
| sky2_set_multicast(dev); |
| |
| return 0; |
| } |
| |
| static void sky2_phy_stats(struct sky2_port *sky2, u64 * data, unsigned count) |
| { |
| struct sky2_hw *hw = sky2->hw; |
| unsigned port = sky2->port; |
| int i; |
| |
| data[0] = (u64) gma_read32(hw, port, GM_TXO_OK_HI) << 32 |
| | (u64) gma_read32(hw, port, GM_TXO_OK_LO); |
| data[1] = (u64) gma_read32(hw, port, GM_RXO_OK_HI) << 32 |
| | (u64) gma_read32(hw, port, GM_RXO_OK_LO); |
| |
| for (i = 2; i < count; i++) |
| data[i] = (u64) gma_read32(hw, port, sky2_stats[i].offset); |
| } |
| |
| static void sky2_set_msglevel(struct net_device *netdev, u32 value) |
| { |
| struct sky2_port *sky2 = netdev_priv(netdev); |
| sky2->msg_enable = value; |
| } |
| |
| static int sky2_get_sset_count(struct net_device *dev, int sset) |
| { |
| switch (sset) { |
| case ETH_SS_STATS: |
| return ARRAY_SIZE(sky2_stats); |
| default: |
| return -EOPNOTSUPP; |
| } |
| } |
| |
| static void sky2_get_ethtool_stats(struct net_device *dev, |
| struct ethtool_stats *stats, u64 * data) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| |
| sky2_phy_stats(sky2, data, ARRAY_SIZE(sky2_stats)); |
| } |
| |
| static void sky2_get_strings(struct net_device *dev, u32 stringset, u8 * data) |
| { |
| int i; |
| |
| switch (stringset) { |
| case ETH_SS_STATS: |
| for (i = 0; i < ARRAY_SIZE(sky2_stats); i++) |
| memcpy(data + i * ETH_GSTRING_LEN, |
| sky2_stats[i].name, ETH_GSTRING_LEN); |
| break; |
| } |
| } |
| |
| static int sky2_set_mac_address(struct net_device *dev, void *p) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| struct sky2_hw *hw = sky2->hw; |
| unsigned port = sky2->port; |
| const struct sockaddr *addr = p; |
| |
| if (!is_valid_ether_addr(addr->sa_data)) |
| return -EADDRNOTAVAIL; |
| |
| memcpy(dev->dev_addr, addr->sa_data, ETH_ALEN); |
| memcpy_toio(hw->regs + B2_MAC_1 + port * 8, |
| dev->dev_addr, ETH_ALEN); |
| memcpy_toio(hw->regs + B2_MAC_2 + port * 8, |
| dev->dev_addr, ETH_ALEN); |
| |
| /* virtual address for data */ |
| gma_set_addr(hw, port, GM_SRC_ADDR_2L, dev->dev_addr); |
| |
| /* physical address: used for pause frames */ |
| gma_set_addr(hw, port, GM_SRC_ADDR_1L, dev->dev_addr); |
| |
| return 0; |
| } |
| |
| static void inline sky2_add_filter(u8 filter[8], const u8 *addr) |
| { |
| u32 bit; |
| |
| bit = ether_crc(ETH_ALEN, addr) & 63; |
| filter[bit >> 3] |= 1 << (bit & 7); |
| } |
| |
| static void sky2_set_multicast(struct net_device *dev) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| struct sky2_hw *hw = sky2->hw; |
| unsigned port = sky2->port; |
| struct dev_mc_list *list = dev->mc_list; |
| u16 reg; |
| u8 filter[8]; |
| int rx_pause; |
| static const u8 pause_mc_addr[ETH_ALEN] = { 0x1, 0x80, 0xc2, 0x0, 0x0, 0x1 }; |
| |
| rx_pause = (sky2->flow_status == FC_RX || sky2->flow_status == FC_BOTH); |
| memset(filter, 0, sizeof(filter)); |
| |
| reg = gma_read16(hw, port, GM_RX_CTRL); |
| reg |= GM_RXCR_UCF_ENA; |
| |
| if (dev->flags & IFF_PROMISC) /* promiscuous */ |
| reg &= ~(GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA); |
| else if (dev->flags & IFF_ALLMULTI) |
| memset(filter, 0xff, sizeof(filter)); |
| else if (dev->mc_count == 0 && !rx_pause) |
| reg &= ~GM_RXCR_MCF_ENA; |
| else { |
| int i; |
| reg |= GM_RXCR_MCF_ENA; |
| |
| if (rx_pause) |
| sky2_add_filter(filter, pause_mc_addr); |
| |
| for (i = 0; list && i < dev->mc_count; i++, list = list->next) |
| sky2_add_filter(filter, list->dmi_addr); |
| } |
| |
| gma_write16(hw, port, GM_MC_ADDR_H1, |
| (u16) filter[0] | ((u16) filter[1] << 8)); |
| gma_write16(hw, port, GM_MC_ADDR_H2, |
| (u16) filter[2] | ((u16) filter[3] << 8)); |
| gma_write16(hw, port, GM_MC_ADDR_H3, |
| (u16) filter[4] | ((u16) filter[5] << 8)); |
| gma_write16(hw, port, GM_MC_ADDR_H4, |
| (u16) filter[6] | ((u16) filter[7] << 8)); |
| |
| gma_write16(hw, port, GM_RX_CTRL, reg); |
| } |
| |
| /* Can have one global because blinking is controlled by |
| * ethtool and that is always under RTNL mutex |
| */ |
| static void sky2_led(struct sky2_port *sky2, enum led_mode mode) |
| { |
| struct sky2_hw *hw = sky2->hw; |
| unsigned port = sky2->port; |
| |
| spin_lock_bh(&sky2->phy_lock); |
| if (hw->chip_id == CHIP_ID_YUKON_EC_U || |
| hw->chip_id == CHIP_ID_YUKON_EX || |
| hw->chip_id == CHIP_ID_YUKON_SUPR) { |
| u16 pg; |
| pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR); |
| gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3); |
| |
| switch (mode) { |
| case MO_LED_OFF: |
| gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, |
| PHY_M_LEDC_LOS_CTRL(8) | |
| PHY_M_LEDC_INIT_CTRL(8) | |
| PHY_M_LEDC_STA1_CTRL(8) | |
| PHY_M_LEDC_STA0_CTRL(8)); |
| break; |
| case MO_LED_ON: |
| gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, |
| PHY_M_LEDC_LOS_CTRL(9) | |
| PHY_M_LEDC_INIT_CTRL(9) | |
| PHY_M_LEDC_STA1_CTRL(9) | |
| PHY_M_LEDC_STA0_CTRL(9)); |
| break; |
| case MO_LED_BLINK: |
| gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, |
| PHY_M_LEDC_LOS_CTRL(0xa) | |
| PHY_M_LEDC_INIT_CTRL(0xa) | |
| PHY_M_LEDC_STA1_CTRL(0xa) | |
| PHY_M_LEDC_STA0_CTRL(0xa)); |
| break; |
| case MO_LED_NORM: |
| gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, |
| PHY_M_LEDC_LOS_CTRL(1) | |
| PHY_M_LEDC_INIT_CTRL(8) | |
| PHY_M_LEDC_STA1_CTRL(7) | |
| PHY_M_LEDC_STA0_CTRL(7)); |
| } |
| |
| gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg); |
| } else |
| gm_phy_write(hw, port, PHY_MARV_LED_OVER, |
| PHY_M_LED_MO_DUP(mode) | |
| PHY_M_LED_MO_10(mode) | |
| PHY_M_LED_MO_100(mode) | |
| PHY_M_LED_MO_1000(mode) | |
| PHY_M_LED_MO_RX(mode) | |
| PHY_M_LED_MO_TX(mode)); |
| |
| spin_unlock_bh(&sky2->phy_lock); |
| } |
| |
| /* blink LED's for finding board */ |
| static int sky2_phys_id(struct net_device *dev, u32 data) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| unsigned int i; |
| |
| if (data == 0) |
| data = UINT_MAX; |
| |
| for (i = 0; i < data; i++) { |
| sky2_led(sky2, MO_LED_ON); |
| if (msleep_interruptible(500)) |
| break; |
| sky2_led(sky2, MO_LED_OFF); |
| if (msleep_interruptible(500)) |
| break; |
| } |
| sky2_led(sky2, MO_LED_NORM); |
| |
| return 0; |
| } |
| |
| static void sky2_get_pauseparam(struct net_device *dev, |
| struct ethtool_pauseparam *ecmd) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| |
| switch (sky2->flow_mode) { |
| case FC_NONE: |
| ecmd->tx_pause = ecmd->rx_pause = 0; |
| break; |
| case FC_TX: |
| ecmd->tx_pause = 1, ecmd->rx_pause = 0; |
| break; |
| case FC_RX: |
| ecmd->tx_pause = 0, ecmd->rx_pause = 1; |
| break; |
| case FC_BOTH: |
| ecmd->tx_pause = ecmd->rx_pause = 1; |
| } |
| |
| ecmd->autoneg = (sky2->flags & SKY2_FLAG_AUTO_PAUSE) |
| ? AUTONEG_ENABLE : AUTONEG_DISABLE; |
| } |
| |
| static int sky2_set_pauseparam(struct net_device *dev, |
| struct ethtool_pauseparam *ecmd) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| |
| if (ecmd->autoneg == AUTONEG_ENABLE) |
| sky2->flags |= SKY2_FLAG_AUTO_PAUSE; |
| else |
| sky2->flags &= ~SKY2_FLAG_AUTO_PAUSE; |
| |
| sky2->flow_mode = sky2_flow(ecmd->rx_pause, ecmd->tx_pause); |
| |
| if (netif_running(dev)) |
| sky2_phy_reinit(sky2); |
| |
| return 0; |
| } |
| |
| static int sky2_get_coalesce(struct net_device *dev, |
| struct ethtool_coalesce *ecmd) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| struct sky2_hw *hw = sky2->hw; |
| |
| if (sky2_read8(hw, STAT_TX_TIMER_CTRL) == TIM_STOP) |
| ecmd->tx_coalesce_usecs = 0; |
| else { |
| u32 clks = sky2_read32(hw, STAT_TX_TIMER_INI); |
| ecmd->tx_coalesce_usecs = sky2_clk2us(hw, clks); |
| } |
| ecmd->tx_max_coalesced_frames = sky2_read16(hw, STAT_TX_IDX_TH); |
| |
| if (sky2_read8(hw, STAT_LEV_TIMER_CTRL) == TIM_STOP) |
| ecmd->rx_coalesce_usecs = 0; |
| else { |
| u32 clks = sky2_read32(hw, STAT_LEV_TIMER_INI); |
| ecmd->rx_coalesce_usecs = sky2_clk2us(hw, clks); |
| } |
| ecmd->rx_max_coalesced_frames = sky2_read8(hw, STAT_FIFO_WM); |
| |
| if (sky2_read8(hw, STAT_ISR_TIMER_CTRL) == TIM_STOP) |
| ecmd->rx_coalesce_usecs_irq = 0; |
| else { |
| u32 clks = sky2_read32(hw, STAT_ISR_TIMER_INI); |
| ecmd->rx_coalesce_usecs_irq = sky2_clk2us(hw, clks); |
| } |
| |
| ecmd->rx_max_coalesced_frames_irq = sky2_read8(hw, STAT_FIFO_ISR_WM); |
| |
| return 0; |
| } |
| |
| /* Note: this affect both ports */ |
| static int sky2_set_coalesce(struct net_device *dev, |
| struct ethtool_coalesce *ecmd) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| struct sky2_hw *hw = sky2->hw; |
| const u32 tmax = sky2_clk2us(hw, 0x0ffffff); |
| |
| if (ecmd->tx_coalesce_usecs > tmax || |
| ecmd->rx_coalesce_usecs > tmax || |
| ecmd->rx_coalesce_usecs_irq > tmax) |
| return -EINVAL; |
| |
| if (ecmd->tx_max_coalesced_frames >= sky2->tx_ring_size-1) |
| return -EINVAL; |
| if (ecmd->rx_max_coalesced_frames > RX_MAX_PENDING) |
| return -EINVAL; |
| if (ecmd->rx_max_coalesced_frames_irq >RX_MAX_PENDING) |
| return -EINVAL; |
| |
| if (ecmd->tx_coalesce_usecs == 0) |
| sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_STOP); |
| else { |
| sky2_write32(hw, STAT_TX_TIMER_INI, |
| sky2_us2clk(hw, ecmd->tx_coalesce_usecs)); |
| sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START); |
| } |
| sky2_write16(hw, STAT_TX_IDX_TH, ecmd->tx_max_coalesced_frames); |
| |
| if (ecmd->rx_coalesce_usecs == 0) |
| sky2_write8(hw, STAT_LEV_TIMER_CTRL, TIM_STOP); |
| else { |
| sky2_write32(hw, STAT_LEV_TIMER_INI, |
| sky2_us2clk(hw, ecmd->rx_coalesce_usecs)); |
| sky2_write8(hw, STAT_LEV_TIMER_CTRL, TIM_START); |
| } |
| sky2_write8(hw, STAT_FIFO_WM, ecmd->rx_max_coalesced_frames); |
| |
| if (ecmd->rx_coalesce_usecs_irq == 0) |
| sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_STOP); |
| else { |
| sky2_write32(hw, STAT_ISR_TIMER_INI, |
| sky2_us2clk(hw, ecmd->rx_coalesce_usecs_irq)); |
| sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_START); |
| } |
| sky2_write8(hw, STAT_FIFO_ISR_WM, ecmd->rx_max_coalesced_frames_irq); |
| return 0; |
| } |
| |
| static void sky2_get_ringparam(struct net_device *dev, |
| struct ethtool_ringparam *ering) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| |
| ering->rx_max_pending = RX_MAX_PENDING; |
| ering->rx_mini_max_pending = 0; |
| ering->rx_jumbo_max_pending = 0; |
| ering->tx_max_pending = TX_MAX_PENDING; |
| |
| ering->rx_pending = sky2->rx_pending; |
| ering->rx_mini_pending = 0; |
| ering->rx_jumbo_pending = 0; |
| ering->tx_pending = sky2->tx_pending; |
| } |
| |
| static int sky2_set_ringparam(struct net_device *dev, |
| struct ethtool_ringparam *ering) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| |
| if (ering->rx_pending > RX_MAX_PENDING || |
| ering->rx_pending < 8 || |
| ering->tx_pending < TX_MIN_PENDING || |
| ering->tx_pending > TX_MAX_PENDING) |
| return -EINVAL; |
| |
| sky2_detach(dev); |
| |
| sky2->rx_pending = ering->rx_pending; |
| sky2->tx_pending = ering->tx_pending; |
| sky2->tx_ring_size = roundup_pow_of_two(sky2->tx_pending+1); |
| |
| return sky2_reattach(dev); |
| } |
| |
| static int sky2_get_regs_len(struct net_device *dev) |
| { |
| return 0x4000; |
| } |
| |
| /* |
| * Returns copy of control register region |
| * Note: ethtool_get_regs always provides full size (16k) buffer |
| */ |
| static void sky2_get_regs(struct net_device *dev, struct ethtool_regs *regs, |
| void *p) |
| { |
| const struct sky2_port *sky2 = netdev_priv(dev); |
| const void __iomem *io = sky2->hw->regs; |
| unsigned int b; |
| |
| regs->version = 1; |
| |
| for (b = 0; b < 128; b++) { |
| /* This complicated switch statement is to make sure and |
| * only access regions that are unreserved. |
| * Some blocks are only valid on dual port cards. |
| * and block 3 has some special diagnostic registers that |
| * are poison. |
| */ |
| switch (b) { |
| case 3: |
| /* skip diagnostic ram region */ |
| memcpy_fromio(p + 0x10, io + 0x10, 128 - 0x10); |
| break; |
| |
| /* dual port cards only */ |
| case 5: /* Tx Arbiter 2 */ |
| case 9: /* RX2 */ |
| case 14 ... 15: /* TX2 */ |
| case 17: case 19: /* Ram Buffer 2 */ |
| case 22 ... 23: /* Tx Ram Buffer 2 */ |
| case 25: /* Rx MAC Fifo 1 */ |
| case 27: /* Tx MAC Fifo 2 */ |
| case 31: /* GPHY 2 */ |
| case 40 ... 47: /* Pattern Ram 2 */ |
| case 52: case 54: /* TCP Segmentation 2 */ |
| case 112 ... 116: /* GMAC 2 */ |
| if (sky2->hw->ports == 1) |
| goto reserved; |
| /* fall through */ |
| case 0: /* Control */ |
| case 2: /* Mac address */ |
| case 4: /* Tx Arbiter 1 */ |
| case 7: /* PCI express reg */ |
| case 8: /* RX1 */ |
| case 12 ... 13: /* TX1 */ |
| case 16: case 18:/* Rx Ram Buffer 1 */ |
| case 20 ... 21: /* Tx Ram Buffer 1 */ |
| case 24: /* Rx MAC Fifo 1 */ |
| case 26: /* Tx MAC Fifo 1 */ |
| case 28 ... 29: /* Descriptor and status unit */ |
| case 30: /* GPHY 1*/ |
| case 32 ... 39: /* Pattern Ram 1 */ |
| case 48: case 50: /* TCP Segmentation 1 */ |
| case 56 ... 60: /* PCI space */ |
| case 80 ... 84: /* GMAC 1 */ |
| memcpy_fromio(p, io, 128); |
| break; |
| default: |
| reserved: |
| memset(p, 0, 128); |
| } |
| |
| p += 128; |
| io += 128; |
| } |
| } |
| |
| /* In order to do Jumbo packets on these chips, need to turn off the |
| * transmit store/forward. Therefore checksum offload won't work. |
| */ |
| static int no_tx_offload(struct net_device *dev) |
| { |
| const struct sky2_port *sky2 = netdev_priv(dev); |
| const struct sky2_hw *hw = sky2->hw; |
| |
| return dev->mtu > ETH_DATA_LEN && hw->chip_id == CHIP_ID_YUKON_EC_U; |
| } |
| |
| static int sky2_set_tx_csum(struct net_device *dev, u32 data) |
| { |
| if (data && no_tx_offload(dev)) |
| return -EINVAL; |
| |
| return ethtool_op_set_tx_csum(dev, data); |
| } |
| |
| |
| static int sky2_set_tso(struct net_device *dev, u32 data) |
| { |
| if (data && no_tx_offload(dev)) |
| return -EINVAL; |
| |
| return ethtool_op_set_tso(dev, data); |
| } |
| |
| static int sky2_get_eeprom_len(struct net_device *dev) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| struct sky2_hw *hw = sky2->hw; |
| u16 reg2; |
| |
| reg2 = sky2_pci_read16(hw, PCI_DEV_REG2); |
| return 1 << ( ((reg2 & PCI_VPD_ROM_SZ) >> 14) + 8); |
| } |
| |
| static int sky2_vpd_wait(const struct sky2_hw *hw, int cap, u16 busy) |
| { |
| unsigned long start = jiffies; |
| |
| while ( (sky2_pci_read16(hw, cap + PCI_VPD_ADDR) & PCI_VPD_ADDR_F) == busy) { |
| /* Can take up to 10.6 ms for write */ |
| if (time_after(jiffies, start + HZ/4)) { |
| dev_err(&hw->pdev->dev, PFX "VPD cycle timed out"); |
| return -ETIMEDOUT; |
| } |
| mdelay(1); |
| } |
| |
| return 0; |
| } |
| |
| static int sky2_vpd_read(struct sky2_hw *hw, int cap, void *data, |
| u16 offset, size_t length) |
| { |
| int rc = 0; |
| |
| while (length > 0) { |
| u32 val; |
| |
| sky2_pci_write16(hw, cap + PCI_VPD_ADDR, offset); |
| rc = sky2_vpd_wait(hw, cap, 0); |
| if (rc) |
| break; |
| |
| val = sky2_pci_read32(hw, cap + PCI_VPD_DATA); |
| |
| memcpy(data, &val, min(sizeof(val), length)); |
| offset += sizeof(u32); |
| data += sizeof(u32); |
| length -= sizeof(u32); |
| } |
| |
| return rc; |
| } |
| |
| static int sky2_vpd_write(struct sky2_hw *hw, int cap, const void *data, |
| u16 offset, unsigned int length) |
| { |
| unsigned int i; |
| int rc = 0; |
| |
| for (i = 0; i < length; i += sizeof(u32)) { |
| u32 val = *(u32 *)(data + i); |
| |
| sky2_pci_write32(hw, cap + PCI_VPD_DATA, val); |
| sky2_pci_write32(hw, cap + PCI_VPD_ADDR, offset | PCI_VPD_ADDR_F); |
| |
| rc = sky2_vpd_wait(hw, cap, PCI_VPD_ADDR_F); |
| if (rc) |
| break; |
| } |
| return rc; |
| } |
| |
| static int sky2_get_eeprom(struct net_device *dev, struct ethtool_eeprom *eeprom, |
| u8 *data) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| int cap = pci_find_capability(sky2->hw->pdev, PCI_CAP_ID_VPD); |
| |
| if (!cap) |
| return -EINVAL; |
| |
| eeprom->magic = SKY2_EEPROM_MAGIC; |
| |
| return sky2_vpd_read(sky2->hw, cap, data, eeprom->offset, eeprom->len); |
| } |
| |
| static int sky2_set_eeprom(struct net_device *dev, struct ethtool_eeprom *eeprom, |
| u8 *data) |
| { |
| struct sky2_port *sky2 = netdev_priv(dev); |
| int cap = pci_find_capability(sky2->hw->pdev, PCI_CAP_ID_VPD); |
| |
| if (!cap) |
| return -EINVAL; |
| |
| if (eeprom->magic != SKY2_EEPROM_MAGIC) |
| return -EINVAL; |
| |
| /* Partial writes not supported */ |
| if ((eeprom->offset & 3) || (eeprom->len & 3)) |
| return -EINVAL; |
| |
| return sky2_vpd_write(sky2->hw, cap, data, eeprom->offset, eeprom->len); |
| } |
| |
| |
| static const struct ethtool_ops sky2_ethtool_ops = { |
| .get_settings = sky2_get_settings, |
| .set_settings = sky2_set_settings, |
| .get_drvinfo = sky2_get_drvinfo, |
| .get_wol = sky2_get_wol, |
| .set_wol = sky2_set_wol, |
| .get_msglevel = sky2_get_msglevel, |
| .set_msglevel = sky2_set_msglevel, |
| .nway_reset = sky2_nway_reset, |
| .get_regs_len = sky2_get_regs_len, |
| .get_regs = sky2_get_regs, |
| .get_link = ethtool_op_get_link, |
| .get_eeprom_len = sky2_get_eeprom_len, |
| .get_eeprom = sky2_get_eeprom, |
| .set_eeprom = sky2_set_eeprom, |
| .set_sg = ethtool_op_set_sg, |
| .set_tx_csum = sky2_set_tx_csum, |
| .set_tso = sky2_set_tso, |
| .get_rx_csum = sky2_get_rx_csum, |
| .set_rx_csum = sky2_set_rx_csum, |
| .get_strings = sky2_get_strings, |
| .get_coalesce = sky2_get_coalesce, |
| .set_coalesce = sky2_set_coalesce, |
| .get_ringparam = sky2_get_ringparam, |
| .set_ringparam = sky2_set_ringparam, |
| .get_pauseparam = sky2_get_pauseparam, |
| .set_pauseparam = sky2_set_pauseparam, |
| .phys_id = sky2_phys_id, |
| .get_sset_count = sky2_get_sset_count, |
| .get_ethtool_stats = sky2_get_ethtool_stats, |
| }; |
| |
| #ifdef CONFIG_SKY2_DEBUG |
| |
| static struct dentry *sky2_debug; |
| |
| |
| /* |
| * Read and parse the first part of Vital Product Data |
| */ |
| #define VPD_SIZE 128 |
| #define VPD_MAGIC 0x82 |
| |
| static const struct vpd_tag { |
| char tag[2]; |
| char *label; |
| } vpd_tags[] = { |
| { "PN", "Part Number" }, |
| { "EC", "Engineering Level" }, |
| { "MN", "Manufacturer" }, |
| { "SN", "Serial Number" }, |
| { "YA", "Asset Tag" }, |
| { "VL", "First Error Log Message" }, |
| { "VF", "Second Error Log Message" }, |
| { "VB", "Boot Agent ROM Configuration" }, |
| { "VE", "EFI UNDI Configuration" }, |
| }; |
| |
| static void sky2_show_vpd(struct seq_file *seq, struct sky2_hw *hw) |
| { |
| size_t vpd_size; |
| loff_t offs; |
| u8 len; |
| unsigned char *buf; |
| u16 reg2; |
| |
| reg2 = sky2_pci_read16(hw, PCI_DEV_REG2); |
| vpd_size = 1 << ( ((reg2 & PCI_VPD_ROM_SZ) >> 14) + 8); |
| |
| seq_printf(seq, "%s Product Data\n", pci_name(hw->pdev)); |
| buf = kmalloc(vpd_size, GFP_KERNEL); |
| if (!buf) { |
| seq_puts(seq, "no memory!\n"); |
| return; |
| } |
| |
| if (pci_read_vpd(hw->pdev, 0, vpd_size, buf) < 0) { |
| seq_puts(seq, "VPD read failed\n"); |
| goto out; |
| } |
| |
| if (buf[0] != VPD_MAGIC) { |
| seq_printf(seq, "VPD tag mismatch: %#x\n", buf[0]); |
| goto out; |
| } |
| len = buf[1]; |
| if (len == 0 || len > vpd_size - 4) { |
| seq_printf(seq, "Invalid id length: %d\n", len); |
| goto out; |
| } |
| |
| seq_printf(seq, "%.*s\n", len, buf + 3); |
| offs = len + 3; |
| |
| while (offs < vpd_size - 4) { |
| int i; |
| |
| if (!memcmp("RW", buf + offs, 2)) /* end marker */ |
| break; |
| len = buf[offs + 2]; |
| if (offs + len + 3 >= vpd_size) |
| break; |
| |
| for (i = 0; i < ARRAY_SIZE(vpd_tags); i++) { |
| if (!memcmp(vpd_tags[i].tag, buf + offs, 2)) { |
| seq_printf(seq, " %s: %.*s\n", |
| vpd_tags[i].label, len, buf + offs + 3); |
| break; |
| } |
| } |
| offs += len + 3; |
| } |
| out: |
| kfree(buf); |
| } |
| |
| static int sky2_debug_show(struct seq_file *seq, void *v) |
| { |
| struct net_device *dev = seq->private; |
| const struct sky2_port *sky2 = netdev_priv(dev); |
| struct sky2_hw *hw = sky2->hw; |
| unsigned port = sky2->port; |
| unsigned idx, last; |
| int sop; |
| |
| sky2_show_vpd(seq, hw); |
| |
| seq_printf(seq, "\nIRQ src=%x mask=%x control=%x\n", |
| sky2_read32(hw, B0_ISRC), |
| sky2_read32(hw, B0_IMSK), |
| sky2_read32(hw, B0_Y2_SP_ICR)); |
| |
| if (!netif_running(dev)) { |
| seq_printf(seq, "network not running\n"); |
| return 0; |
| } |
| |
| napi_disable(&hw->napi); |
| last = sky2_read16(hw, STAT_PUT_IDX); |
| |
| if (hw->st_idx == last) |
| seq_puts(seq, "Status ring (empty)\n"); |
| else { |
| seq_puts(seq, "Status ring\n"); |
| for (idx = hw->st_idx; idx != last && idx < STATUS_RING_SIZE; |
| idx = RING_NEXT(idx, STATUS_RING_SIZE)) { |
| const struct sky2_status_le *le = hw->st_le + idx; |
| seq_printf(seq, "[%d] %#x %d %#x\n", |
| idx, le->opcode, le->length, le->status); |
| } |
| seq_puts(seq, "\n"); |
| } |
| |
| seq_printf(seq, "Tx ring pending=%u...%u report=%d done=%d\n", |
| sky2->tx_cons, sky2->tx_prod, |
| sky2_read16(hw, port == 0 ? STAT_TXA1_RIDX : STAT_TXA2_RIDX), |
| sky2_read16(hw, Q_ADDR(txqaddr[port], Q_DONE))); |
| |
| /* Dump contents of tx ring */ |
| sop = 1; |
| for (idx = sky2->tx_next; idx != sky2->tx_prod && idx < sky2->tx_ring_size; |
| idx = RING_NEXT(idx, sky2->tx_ring_size)) { |
| const struct sky2_tx_le *le = sky2->tx_le + idx; |
| u32 a = le32_to_cpu(le->addr); |
| |
| if (sop) |
| seq_printf(seq, "%u:", idx); |
| sop = 0; |
| |
| switch(le->opcode & ~HW_OWNER) { |
| case OP_ADDR64: |
| seq_printf(seq, " %#x:", a); |
| break; |
| case OP_LRGLEN: |
| seq_printf(seq, " mtu=%d", a); |
| break; |
| case OP_VLAN: |
| seq_printf(seq, " vlan=%d", be16_to_cpu(le->length)); |
| break; |
| case OP_TCPLISW: |
| seq_printf(seq, " csum=%#x", a); |
| break; |
| case OP_LARGESEND: |
| seq_printf(seq, " tso=%#x(%d)", a, le16_to_cpu(le->length)); |
| break; |
| case OP_PACKET: |
| seq_printf(seq, " %#x(%d)", a, le16_to_cpu(le->length)); |
| break; |
| case OP_BUFFER: |
| seq_printf(seq, " frag=%#x(%d)", a, le16_to_cpu(le->length)); |
| break; |
| default: |
| seq_printf(seq, " op=%#x,%#x(%d)", le->opcode, |
| a, le16_to_cpu(le->length)); |
| } |
| |
| if (le->ctrl & EOP) { |
| seq_putc(seq, '\n'); |
| sop = 1; |
| } |
| } |
| |
| seq_printf(seq, "\nRx ring hw get=%d put=%d last=%d\n", |
| sky2_read16(hw, Y2_QADDR(rxqaddr[port], PREF_UNIT_GET_IDX)), |
| sky2_read16(hw, Y2_QADDR(rxqaddr[port], PREF_UNIT_PUT_IDX)), |
| sky2_read16(hw, Y2_QADDR(rxqaddr[port], PREF_UNIT_LAST_IDX))); |
| |
| sky2_read32(hw, B0_Y2_SP_LISR); |
| napi_enable(&hw->napi); |
| return 0; |
| } |
| |
| static int sky2_debug_open(struct inode *inode, struct file *file) |
| { |
| return single_open(file, sky2_debug_show, inode->i_private); |
| } |
| |
| static const struct file_operations sky2_debug_fops = { |
| .owner = THIS_MODULE, |
| .open = sky2_debug_open, |
| .read = seq_read, |
| .llseek = seq_lseek, |
| .release = single_release, |
| }; |
| |
| /* |
| * Use network device events to create/remove/rename |
| * debugfs file entries |
| */ |
| static int sky2_device_event(struct notifier_block *unused, |
| unsigned long event, void *ptr) |
| { |
| struct net_device *dev = ptr; |
| struct sky2_port *sky2 = netdev_priv(dev); |
| |
| if (dev->netdev_ops->ndo_open != sky2_up || !sky2_debug) |
| return NOTIFY_DONE; |
| |
| switch(event) { |
| case NETDEV_CHANGENAME: |
| if (sky2->debugfs) { |
| sky2->debugfs = debugfs_rename(sky2_debug, sky2->debugfs, |
| sky2_debug, dev->name); |
| } |
| break; |
| |
| case NETDEV_GOING_DOWN: |
| if (sky2->debugfs) { |
| printk(KERN_DEBUG PFX "%s: remove debugfs\n", |
| dev->name); |
| debugfs_remove(sky2->debugfs); |
| sky2->debugfs = NULL; |
| } |
| break; |
| |
| case NETDEV_UP: |
| sky2->debugfs = debugfs_create_file(dev->name, S_IRUGO, |
| sky2_debug, dev, |
| &sky2_debug_fops); |
| if (IS_ERR(sky2->debugfs)) |
| sky2->debugfs = NULL; |
| } |
| |
| return NOTIFY_DONE; |
| } |
| |
| static struct notifier_block sky2_notifier = { |
| .notifier_call = sky2_device_event, |
| }; |
| |
| |
| static __init void sky2_debug_init(void) |
| { |
| struct dentry *ent; |
| |
| ent = debugfs_create_dir("sky2", NULL); |
| if (!ent || IS_ERR(ent)) |
| return; |
| |
| sky2_debug = ent; |
| register_netdevice_notifier(&sky2_notifier); |
| } |
| |
| static __exit void sky2_debug_cleanup(void) |
| { |
| if (sky2_debug) { |
| unregister_netdevice_notifier(&sky2_notifier); |
| debugfs_remove(sky2_debug); |
| sky2_debug = NULL; |
| } |
| } |
| |
| #else |
| #define sky2_debug_init() |
| #define sky2_debug_cleanup() |
| #endif |
| |
| /* Two copies of network device operations to handle special case of |
| not allowing netpoll on second port */ |
| static const struct net_device_ops sky2_netdev_ops[2] = { |
| { |
| .ndo_open = sky2_up, |
| .ndo_stop = sky2_down, |
| .ndo_start_xmit = sky2_xmit_frame, |
| .ndo_do_ioctl = sky2_ioctl, |
| .ndo_validate_addr = eth_validate_addr, |
| .ndo_set_mac_address = sky2_set_mac_address, |
| .ndo_set_multicast_list = sky2_set_multicast, |
| .ndo_change_mtu = sky2_change_mtu, |
| .ndo_tx_timeout = sky2_tx_timeout, |
| #ifdef SKY2_VLAN_TAG_USED |
| .ndo_vlan_rx_register = sky2_vlan_rx_register, |
| #endif |
| #ifdef CONFIG_NET_POLL_CONTROLLER |
| .ndo_poll_controller = sky2_netpoll, |
| #endif |
| }, |
| { |
| .ndo_open = sky2_up, |
| .ndo_stop = sky2_down, |
| .ndo_start_xmit = sky2_xmit_frame, |
| .ndo_do_ioctl = sky2_ioctl, |
| .ndo_validate_addr = eth_validate_addr, |
| .ndo_set_mac_address = sky2_set_mac_address, |
| .ndo_set_multicast_list = sky2_set_multicast, |
| .ndo_change_mtu = sky2_change_mtu, |
| .ndo_tx_timeout = sky2_tx_timeout, |
| #ifdef SKY2_VLAN_TAG_USED |
| .ndo_vlan_rx_register = sky2_vlan_rx_register, |
| #endif |
| }, |
| }; |
| |
| /* Initialize network device */ |
| static __devinit struct net_device *sky2_init_netdev(struct sky2_hw *hw, |
| unsigned port, |
| int highmem, int wol) |
| { |
| struct sky2_port *sky2; |
| struct net_device *dev = alloc_etherdev(sizeof(*sky2)); |
| |
| if (!dev) { |
| dev_err(&hw->pdev->dev, "etherdev alloc failed\n"); |
| return NULL; |
| } |
| |
| SET_NETDEV_DEV(dev, &hw->pdev->dev); |
| dev->irq = hw->pdev->irq; |
| SET_ETHTOOL_OPS(dev, &sky2_ethtool_ops); |
| dev->watchdog_timeo = TX_WATCHDOG; |
| dev->netdev_ops = &sky2_netdev_ops[port]; |
| |
| sky2 = netdev_priv(dev); |
| sky2->netdev = dev; |
| sky2->hw = hw; |
| sky2->msg_enable = netif_msg_init(debug, default_msg); |
| |
| /* Auto speed and flow control */ |
| sky2->flags = SKY2_FLAG_AUTO_SPEED | SKY2_FLAG_AUTO_PAUSE; |
| if (hw->chip_id != CHIP_ID_YUKON_XL) |
| sky2->flags |= SKY2_FLAG_RX_CHECKSUM; |
| |
| sky2->flow_mode = FC_BOTH; |
| |
| sky2->duplex = -1; |
| sky2->speed = -1; |
| sky2->advertising = sky2_supported_modes(hw); |
| sky2->wol = wol; |
| |
| spin_lock_init(&sky2->phy_lock); |
| |
| sky2->tx_pending = TX_DEF_PENDING; |
| sky2->tx_ring_size = roundup_pow_of_two(TX_DEF_PENDING+1); |
| sky2->rx_pending = RX_DEF_PENDING; |
| |
| hw->dev[port] = dev; |
| |
| sky2->port = port; |
| |
| dev->features |= NETIF_F_TSO | NETIF_F_IP_CSUM | NETIF_F_SG; |
| if (highmem) |
| dev->features |= NETIF_F_HIGHDMA; |
| |
| #ifdef SKY2_VLAN_TAG_USED |
| /* The workaround for FE+ status conflicts with VLAN tag detection. */ |
| if (!(sky2->hw->chip_id == CHIP_ID_YUKON_FE_P && |
| sky2->hw->chip_rev == CHIP_REV_YU_FE2_A0)) { |
| dev->features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX; |
| } |
| #endif |
| |
| /* read the mac address */ |
| memcpy_fromio(dev->dev_addr, hw->regs + B2_MAC_1 + port * 8, ETH_ALEN); |
| memcpy(dev->perm_addr, dev->dev_addr, dev->addr_len); |
| |
| return dev; |
| } |
| |
| static void __devinit sky2_show_addr(struct net_device *dev) |
| { |
| const struct sky2_port *sky2 = netdev_priv(dev); |
| |
| if (netif_msg_probe(sky2)) |
| printk(KERN_INFO PFX "%s: addr %pM\n", |
| dev->name, dev->dev_addr); |
| } |
| |
| /* Handle software interrupt used during MSI test */ |
| static irqreturn_t __devinit sky2_test_intr(int irq, void *dev_id) |
| { |
| struct sky2_hw *hw = dev_id; |
| u32 status = sky2_read32(hw, B0_Y2_SP_ISRC2); |
| |
| if (status == 0) |
| return IRQ_NONE; |
| |
| if (status & Y2_IS_IRQ_SW) { |
| hw->flags |= SKY2_HW_USE_MSI; |
| wake_up(&hw->msi_wait); |
| sky2_write8(hw, B0_CTST, CS_CL_SW_IRQ); |
| } |
| sky2_write32(hw, B0_Y2_SP_ICR, 2); |
| |
| return IRQ_HANDLED; |
| } |
| |
| /* Test interrupt path by forcing a a software IRQ */ |
| static int __devinit sky2_test_msi(struct sky2_hw *hw) |
| { |
| struct pci_dev *pdev = hw->pdev; |
| int err; |
| |
| init_waitqueue_head (&hw->msi_wait); |
| |
| sky2_write32(hw, B0_IMSK, Y2_IS_IRQ_SW); |
| |
| err = request_irq(pdev->irq, sky2_test_intr, 0, DRV_NAME, hw); |
| if (err) { |
| dev_err(&pdev->dev, "cannot assign irq %d\n", pdev->irq); |
| return err; |
| } |
| |
| sky2_write8(hw, B0_CTST, CS_ST_SW_IRQ); |
| sky2_read8(hw, B0_CTST); |
| |
| wait_event_timeout(hw->msi_wait, (hw->flags & SKY2_HW_USE_MSI), HZ/10); |
| |
| if (!(hw->flags & SKY2_HW_USE_MSI)) { |
| /* MSI test failed, go back to INTx mode */ |
| dev_info(&pdev->dev, "No interrupt generated using MSI, " |
| "switching to INTx mode.\n"); |
| |
| err = -EOPNOTSUPP; |
| sky2_write8(hw, B0_CTST, CS_CL_SW_IRQ); |
| } |
| |
| sky2_write32(hw, B0_IMSK, 0); |
| sky2_read32(hw, B0_IMSK); |
| |
| free_irq(pdev->irq, hw); |
| |
| return err; |
| } |
| |
| /* This driver supports yukon2 chipset only */ |
| static const char *sky2_name(u8 chipid, char *buf, int sz) |
| { |
| const char *name[] = { |
| "XL", /* 0xb3 */ |
| "EC Ultra", /* 0xb4 */ |
| "Extreme", /* 0xb5 */ |
| "EC", /* 0xb6 */ |
| "FE", /* 0xb7 */ |
| "FE+", /* 0xb8 */ |
| "Supreme", /* 0xb9 */ |
| "UL 2", /* 0xba */ |
| }; |
| |
| if (chipid >= CHIP_ID_YUKON_XL && chipid < CHIP_ID_YUKON_UL_2) |
| strncpy(buf, name[chipid - CHIP_ID_YUKON_XL], sz); |
| else |
| snprintf(buf, sz, "(chip %#x)", chipid); |
| return buf; |
| } |
| |
| static int __devinit sky2_probe(struct pci_dev *pdev, |
| const struct pci_device_id *ent) |
| { |
| struct net_device *dev; |
| struct sky2_hw *hw; |
| int err, using_dac = 0, wol_default; |
| u32 reg; |
| char buf1[16]; |
| |
| err = pci_enable_device(pdev); |
| if (err) { |
| dev_err(&pdev->dev, "cannot enable PCI device\n"); |
| goto err_out; |
| } |
| |
| /* Get configuration information |
| * Note: only regular PCI config access once to test for HW issues |
| * other PCI access through shared memory for speed and to |
| * avoid MMCONFIG problems. |
| */ |
| err = pci_read_config_dword(pdev, PCI_DEV_REG2, ®); |
| if (err) { |
| dev_err(&pdev->dev, "PCI read config failed\n"); |
| goto err_out; |
| } |
| |
| if (~reg == 0) { |
| dev_err(&pdev->dev, "PCI configuration read error\n"); |
| goto err_out; |
| } |
| |
| err = pci_request_regions(pdev, DRV_NAME); |
| if (err) { |
| dev_err(&pdev->dev, "cannot obtain PCI resources\n"); |
| goto err_out_disable; |
| } |
| |
| pci_set_master(pdev); |
| |
| if (sizeof(dma_addr_t) > sizeof(u32) && |
| !(err = pci_set_dma_mask(pdev, DMA_BIT_MASK(64)))) { |
| using_dac = 1; |
| err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64)); |
| if (err < 0) { |
| dev_err(&pdev->dev, "unable to obtain 64 bit DMA " |
| "for consistent allocations\n"); |
| goto err_out_free_regions; |
| } |
| } else { |
| err = pci_set_dma_mask(pdev, DMA_BIT_MASK(32)); |
| if (err) { |
| dev_err(&pdev->dev, "no usable DMA configuration\n"); |
| goto err_out_free_regions; |
| } |
| } |
| |
| |
| #ifdef __BIG_ENDIAN |
| /* The sk98lin vendor driver uses hardware byte swapping but |
| * this driver uses software swapping. |
| */ |
| reg &= ~PCI_REV_DESC; |
| err = pci_write_config_dword(pdev,PCI_DEV_REG2, reg); |
| if (err) { |
| dev_err(&pdev->dev, "PCI write config failed\n"); |
| goto err_out_free_regions; |
| } |
| #endif |
| |
| wol_default = device_may_wakeup(&pdev->dev) ? WAKE_MAGIC : 0; |
| |
| err = -ENOMEM; |
| |
| hw = kzalloc(sizeof(*hw) + strlen(DRV_NAME "@pci:") |
| + strlen(pci_name(pdev)) + 1, GFP_KERNEL); |
| if (!hw) { |
| dev_err(&pdev->dev, "cannot allocate hardware struct\n"); |
| goto err_out_free_regions; |
| } |
| |
| hw->pdev = pdev; |
| sprintf(hw->irq_name, DRV_NAME "@pci:%s", pci_name(pdev)); |
| |
| hw->regs = ioremap_nocache(pci_resource_start(pdev, 0), 0x4000); |
| if (!hw->regs) { |
| dev_err(&pdev->dev, "cannot map device registers\n"); |
| goto err_out_free_hw; |
| } |
| |
| /* ring for status responses */ |
| hw->st_le = pci_alloc_consistent(pdev, STATUS_LE_BYTES, &hw->st_dma); |
| if (!hw->st_le) |
| goto err_out_iounmap; |
| |
| err = sky2_init(hw); |
| if (err) |
| goto err_out_iounmap; |
| |
| dev_info(&pdev->dev, "Yukon-2 %s chip revision %d\n", |
| sky2_name(hw->chip_id, buf1, sizeof(buf1)), hw->chip_rev); |
| |
| sky2_reset(hw); |
| |
| dev = sky2_init_netdev(hw, 0, using_dac, wol_default); |
| if (!dev) { |
| err = -ENOMEM; |
| goto err_out_free_pci; |
| } |
| |
| if (!disable_msi && pci_enable_msi(pdev) == 0) { |
| err = sky2_test_msi(hw); |
| if (err == -EOPNOTSUPP) |
| pci_disable_msi(pdev); |
| else if (err) |
| goto err_out_free_netdev; |
| } |
| |
| err = register_netdev(dev); |
| if (err) { |
| dev_err(&pdev->dev, "cannot register net device\n"); |
| goto err_out_free_netdev; |
| } |
| |
| netif_napi_add(dev, &hw->napi, sky2_poll, NAPI_WEIGHT); |
| |
| err = request_irq(pdev->irq, sky2_intr, |
| (hw->flags & SKY2_HW_USE_MSI) ? 0 : IRQF_SHARED, |
| hw->irq_name, hw); |
| if (err) { |
| dev_err(&pdev->dev, "cannot assign irq %d\n", pdev->irq); |
| goto err_out_unregister; |
| } |
| sky2_write32(hw, B0_IMSK, Y2_IS_BASE); |
| napi_enable(&hw->napi); |
| |
| sky2_show_addr(dev); |
| |
| if (hw->ports > 1) { |
| struct net_device *dev1; |
| |
| err = -ENOMEM; |
| dev1 = sky2_init_netdev(hw, 1, using_dac, wol_default); |
| if (dev1 && (err = register_netdev(dev1)) == 0) |
| sky2_show_addr(dev1); |
| else { |
| dev_warn(&pdev->dev, |
| "register of second port failed (%d)\n", err); |
| hw->dev[1] = NULL; |
| hw->ports = 1; |
| if (dev1) |
| free_netdev(dev1); |
| } |
| } |
| |
| setup_timer(&hw->watchdog_timer, sky2_watchdog, (unsigned long) hw); |
| INIT_WORK(&hw->restart_work, sky2_restart); |
| |
| pci_set_drvdata(pdev, hw); |
| |
| return 0; |
| |
| err_out_unregister: |
| if (hw->flags & SKY2_HW_USE_MSI) |
| pci_disable_msi(pdev); |
| unregister_netdev(dev); |
| err_out_free_netdev: |
| free_netdev(dev); |
| err_out_free_pci: |
| sky2_write8(hw, B0_CTST, CS_RST_SET); |
| pci_free_consistent(pdev, STATUS_LE_BYTES, hw->st_le, hw->st_dma); |
| err_out_iounmap: |
| iounmap(hw->regs); |
| err_out_free_hw: |
| kfree(hw); |
| err_out_free_regions: |
| pci_release_regions(pdev); |
| err_out_disable: |
| pci_disable_device(pdev); |
| err_out: |
| pci_set_drvdata(pdev, NULL); |
| return err; |
| } |
| |
| static void __devexit sky2_remove(struct pci_dev *pdev) |
| { |
| struct sky2_hw *hw = pci_get_drvdata(pdev); |
| int i; |
| |
| if (!hw) |
| return; |
| |
| del_timer_sync(&hw->watchdog_timer); |
| cancel_work_sync(&hw->restart_work); |
| |
| for (i = hw->ports-1; i >= 0; --i) |
| unregister_netdev(hw->dev[i]); |
| |
| sky2_write32(hw, B0_IMSK, 0); |
| |
| sky2_power_aux(hw); |
| |
| sky2_write8(hw, B0_CTST, CS_RST_SET); |
| sky2_read8(hw, B0_CTST); |
| |
| free_irq(pdev->irq, hw); |
| if (hw->flags & SKY2_HW_USE_MSI) |
| pci_disable_msi(pdev); |
| pci_free_consistent(pdev, STATUS_LE_BYTES, hw->st_le, hw->st_dma); |
| pci_release_regions(pdev); |
| pci_disable_device(pdev); |
| |
| for (i = hw->ports-1; i >= 0; --i) |
| free_netdev(hw->dev[i]); |
| |
| iounmap(hw->regs); |
| kfree(hw); |
| |
| pci_set_drvdata(pdev, NULL); |
| } |
| |
| #ifdef CONFIG_PM |
| static int sky2_suspend(struct pci_dev *pdev, pm_message_t state) |
| { |
| struct sky2_hw *hw = pci_get_drvdata(pdev); |
| int i, wol = 0; |
| |
| if (!hw) |
| return 0; |
| |
| del_timer_sync(&hw->watchdog_timer); |
| cancel_work_sync(&hw->restart_work); |
| |
| rtnl_lock(); |
| for (i = 0; i < hw->ports; i++) { |
| struct net_device *dev = hw->dev[i]; |
| struct sky2_port *sky2 = netdev_priv(dev); |
| |
| sky2_detach(dev); |
| |
| if (sky2->wol) |
| sky2_wol_init(sky2); |
| |
| wol |= sky2->wol; |
| } |
| |
| sky2_write32(hw, B0_IMSK, 0); |
| napi_disable(&hw->napi); |
| sky2_power_aux(hw); |
| rtnl_unlock(); |
| |
| pci_save_state(pdev); |
| pci_enable_wake(pdev, pci_choose_state(pdev, state), wol); |
| pci_set_power_state(pdev, pci_choose_state(pdev, state)); |
| |
| return 0; |
| } |
| |
| static int sky2_resume(struct pci_dev *pdev) |
| { |
| struct sky2_hw *hw = pci_get_drvdata(pdev); |
| int i, err; |
| |
| if (!hw) |
| return 0; |
| |
| err = pci_set_power_state(pdev, PCI_D0); |
| if (err) |
| goto out; |
| |
| err = pci_restore_state(pdev); |
| if (err) |
| goto out; |
| |
| pci_enable_wake(pdev, PCI_D0, 0); |
| |
| /* Re-enable all clocks */ |
| if (hw->chip_id == CHIP_ID_YUKON_EX || |
| hw->chip_id == CHIP_ID_YUKON_EC_U || |
| hw->chip_id == CHIP_ID_YUKON_FE_P) |
| sky2_pci_write32(hw, PCI_DEV_REG3, 0); |
| |
| sky2_reset(hw); |
| sky2_write32(hw, B0_IMSK, Y2_IS_BASE); |
| napi_enable(&hw->napi); |
| |
| rtnl_lock(); |
| for (i = 0; i < hw->ports; i++) { |
| err = sky2_reattach(hw->dev[i]); |
| if (err) |
| goto out; |
| } |
| rtnl_unlock(); |
| |
| return 0; |
| out: |
| rtnl_unlock(); |
| |
| dev_err(&pdev->dev, "resume failed (%d)\n", err); |
| pci_disable_device(pdev); |
| return err; |
| } |
| #endif |
| |
| static void sky2_shutdown(struct pci_dev *pdev) |
| { |
| struct sky2_hw *hw = pci_get_drvdata(pdev); |
| int i, wol = 0; |
| |
| if (!hw) |
| return; |
| |
| rtnl_lock(); |
| del_timer_sync(&hw->watchdog_timer); |
| |
| for (i = 0; i < hw->ports; i++) { |
| struct net_device *dev = hw->dev[i]; |
| struct sky2_port *sky2 = netdev_priv(dev); |
| |
| if (sky2->wol) { |
| wol = 1; |
| sky2_wol_init(sky2); |
| } |
| } |
| |
| if (wol) |
| sky2_power_aux(hw); |
| rtnl_unlock(); |
| |
| pci_enable_wake(pdev, PCI_D3hot, wol); |
| pci_enable_wake(pdev, PCI_D3cold, wol); |
| |
| pci_disable_device(pdev); |
| pci_set_power_state(pdev, PCI_D3hot); |
| } |
| |
| static struct pci_driver sky2_driver = { |
| .name = DRV_NAME, |
| .id_table = sky2_id_table, |
| .probe = sky2_probe, |
| .remove = __devexit_p(sky2_remove), |
| #ifdef CONFIG_PM |
| .suspend = sky2_suspend, |
| .resume = sky2_resume, |
| #endif |
| .shutdown = sky2_shutdown, |
| }; |
| |
| static int __init sky2_init_module(void) |
| { |
| pr_info(PFX "driver version " DRV_VERSION "\n"); |
| |
| sky2_debug_init(); |
| return pci_register_driver(&sky2_driver); |
| } |
| |
| static void __exit sky2_cleanup_module(void) |
| { |
| pci_unregister_driver(&sky2_driver); |
| sky2_debug_cleanup(); |
| } |
| |
| module_init(sky2_init_module); |
| module_exit(sky2_cleanup_module); |
| |
| MODULE_DESCRIPTION("Marvell Yukon 2 Gigabit Ethernet driver"); |
| MODULE_AUTHOR("Stephen Hemminger <shemminger@linux-foundation.org>"); |
| MODULE_LICENSE("GPL"); |
| MODULE_VERSION(DRV_VERSION); |