bnx2x: Supporting BCM8727 PHY
Adding support for BCM8727 - a dual port SFP+ PHY. That includes verification of
the optic module vendor and part number - the list of approved modules resides
on the nvram and the module is verified by the FW. Since not all users would
like to use this verification feature, it can be disabled. The default behavior
is to issue a warning if the module is not approved, but still allow using it -
but it is also possible to disable the link if the module is not approved.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/bnx2x_hsi.h b/drivers/net/bnx2x_hsi.h
index 41c6dcb..7de83c4 100644
--- a/drivers/net/bnx2x_hsi.h
+++ b/drivers/net/bnx2x_hsi.h
@@ -248,6 +248,8 @@
#define PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726 0x00000600
#define PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481 0x00000700
#define PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101 0x00000800
+#define PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727 0x00000900
+#define PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727_NOC 0x00000a00
#define PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE 0x0000fd00
#define PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN 0x0000ff00
@@ -358,10 +360,16 @@
#define PORT_FEATURE_MBA_ENABLED 0x02000000
#define PORT_FEATURE_MFW_ENABLED 0x04000000
- /* Check the optic vendor via i2c before allowing it to be used by
- SW */
-#define PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLED 0x00000000
-#define PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_ENABLED 0x08000000
+ /* Reserved bits: 28-29 */
+ /* Check the optic vendor via i2c against a list of approved modules
+ in a separate nvram image */
+#define PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK 0xE0000000
+#define PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_SHIFT 29
+#define PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_NO_ENFORCEMENT 0x00000000
+#define PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLE_TX_LASER 0x20000000
+#define PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_WARNING_MSG 0x40000000
+#define PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_POWER_DOWN 0x60000000
+
u32 wol_config;
/* Default is used when driver sets to "auto" mode */
@@ -657,6 +665,12 @@
#define DRV_MSG_CODE_GET_UPGRADE_KEY 0x81000000
#define DRV_MSG_CODE_GET_MANUF_KEY 0x82000000
#define DRV_MSG_CODE_LOAD_L2B_PRAM 0x90000000
+ /*
+ * The optic module verification commands requris bootcode
+ * v5.0.6 or later
+ */
+#define DRV_MSG_CODE_VRFY_OPT_MDL 0xa0000000
+#define REQ_BC_VER_4_VRFY_OPT_MDL 0x00050006
#define BIOS_MSG_CODE_LIC_CHALLENGE 0xff010000
#define BIOS_MSG_CODE_LIC_RESPONSE 0xff020000
@@ -691,6 +705,9 @@
#define FW_MSG_CODE_L2B_PRAM_C_LOAD_FAILURE 0x90220000
#define FW_MSG_CODE_L2B_PRAM_X_LOAD_FAILURE 0x90230000
#define FW_MSG_CODE_L2B_PRAM_U_LOAD_FAILURE 0x90240000
+#define FW_MSG_CODE_VRFY_OPT_MDL_SUCCESS 0xa0100000
+#define FW_MSG_CODE_VRFY_OPT_MDL_INVLD_IMG 0xa0200000
+#define FW_MSG_CODE_VRFY_OPT_MDL_UNAPPROVED 0xa0300000
#define FW_MSG_CODE_LIC_CHALLENGE 0xff010000
#define FW_MSG_CODE_LIC_RESPONSE 0xff020000