| /* |
| * Driver for Microtune MT2060 "Single chip dual conversion broadband tuner" |
| * |
| * Copyright (c) 2006 Olivier DANET <odanet@caramail.com> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.= |
| */ |
| |
| #ifndef MT2060_PRIV_H |
| #define MT2060_PRIV_H |
| |
| // Uncomment the #define below to enable spurs checking. The results where quite unconvincing. |
| // #define MT2060_SPURCHECK |
| |
| /* This driver is based on the information available in the datasheet of the |
| "Comtech SDVBT-3K6M" tuner ( K1000737843.pdf ) which features the MT2060 register map : |
| |
| I2C Address : 0x60 |
| |
| Reg.No | B7 | B6 | B5 | B4 | B3 | B2 | B1 | B0 | ( defaults ) |
| -------------------------------------------------------------------------------- |
| 00 | [ PART ] | [ REV ] | R = 0x63 |
| 01 | [ LNABAND ] | [ NUM1(5:2) ] | RW = 0x3F |
| 02 | [ DIV1 ] | RW = 0x74 |
| 03 | FM1CA | FM1SS | [ NUM1(1:0) ] | [ NUM2(3:0) ] | RW = 0x00 |
| 04 | NUM2(11:4) ] | RW = 0x08 |
| 05 | [ DIV2 ] |NUM2(12)| RW = 0x93 |
| 06 | L1LK | [ TAD1 ] | L2LK | [ TAD2 ] | R |
| 07 | [ FMF ] | R |
| 08 | ? | FMCAL | ? | ? | ? | ? | ? | TEMP | R |
| 09 | 0 | 0 | [ FMGC ] | 0 | GP02 | GP01 | 0 | RW = 0x20 |
| 0A | ?? |
| 0B | 0 | 0 | 1 | 1 | 0 | 0 | [ VGAG ] | RW = 0x30 |
| 0C | V1CSE | 1 | 1 | 1 | 1 | 1 | 1 | 1 | RW = 0xFF |
| 0D | 1 | 0 | [ V1CS ] | RW = 0xB0 |
| 0E | ?? |
| 0F | ?? |
| 10 | ?? |
| 11 | [ LOTO ] | 0 | 0 | 1 | 0 | RW = 0x42 |
| |
| PART : Part code : 6 for MT2060 |
| REV : Revision code : 3 for current revision |
| LNABAND : Input frequency range : ( See code for details ) |
| NUM1 / DIV1 / NUM2 / DIV2 : Frequencies programming ( See code for details ) |
| FM1CA : Calibration Start Bit |
| FM1SS : Calibration Single Step bit |
| L1LK : LO1 Lock Detect |
| TAD1 : Tune Line ADC ( ? ) |
| L2LK : LO2 Lock Detect |
| TAD2 : Tune Line ADC ( ? ) |
| FMF : Estimated first IF Center frequency Offset ( ? ) |
| FM1CAL : Calibration done bit |
| TEMP : On chip temperature sensor |
| FMCG : Mixer 1 Cap Gain ( ? ) |
| GP01 / GP02 : Programmable digital outputs. Unconnected pins ? |
| V1CSE : LO1 VCO Automatic Capacitor Select Enable ( ? ) |
| V1CS : LO1 Capacitor Selection Value ( ? ) |
| LOTO : LO Timeout ( ? ) |
| VGAG : Tuner Output gain |
| */ |
| |
| #define I2C_ADDRESS 0x60 |
| |
| #define REG_PART_REV 0 |
| #define REG_LO1C1 1 |
| #define REG_LO1C2 2 |
| #define REG_LO2C1 3 |
| #define REG_LO2C2 4 |
| #define REG_LO2C3 5 |
| #define REG_LO_STATUS 6 |
| #define REG_FM_FREQ 7 |
| #define REG_MISC_STAT 8 |
| #define REG_MISC_CTRL 9 |
| #define REG_RESERVED_A 0x0A |
| #define REG_VGAG 0x0B |
| #define REG_LO1B1 0x0C |
| #define REG_LO1B2 0x0D |
| #define REG_LOTO 0x11 |
| |
| #define PART_REV 0x63 // The current driver works only with PART=6 and REV=3 chips |
| |
| #endif |