| /* |
| * Common Blackfin startup code |
| * |
| * Copyright 2004-2008 Analog Devices Inc. |
| * |
| * Licensed under the GPL-2 or later. |
| */ |
| |
| #include <linux/linkage.h> |
| #include <linux/init.h> |
| #include <asm/blackfin.h> |
| #include <asm/thread_info.h> |
| #include <asm/trace.h> |
| #include <asm/asm-offsets.h> |
| |
| __INIT |
| |
| ENTRY(__init_clear_bss) |
| r2 = r2 - r1; |
| cc = r2 == 0; |
| if cc jump .L_bss_done; |
| r2 >>= 2; |
| p1 = r1; |
| p2 = r2; |
| lsetup (1f, 1f) lc0 = p2; |
| 1: [p1++] = r0; |
| .L_bss_done: |
| rts; |
| ENDPROC(__init_clear_bss) |
| |
| ENTRY(__start) |
| /* R0: argument of command line string, passed from uboot, save it */ |
| R7 = R0; |
| |
| /* Enable Cycle Counter and Nesting Of Interrupts */ |
| #ifdef CONFIG_BFIN_SCRATCH_REG_CYCLES |
| R0 = SYSCFG_SNEN; |
| #else |
| R0 = SYSCFG_SNEN | SYSCFG_CCEN; |
| #endif |
| SYSCFG = R0; |
| |
| /* Optimization register tricks: keep a base value in the |
| * reserved P registers so we use the load/store with an |
| * offset syntax. R0 = [P5 + <constant>]; |
| * P5 - core MMR base |
| * R6 - 0 |
| */ |
| r6 = 0; |
| p5.l = 0; |
| p5.h = hi(COREMMR_BASE); |
| |
| /* Zero out registers required by Blackfin ABI */ |
| |
| /* Disable circular buffers */ |
| L0 = r6; |
| L1 = r6; |
| L2 = r6; |
| L3 = r6; |
| |
| /* Disable hardware loops in case we were started by 'go' */ |
| LC0 = r6; |
| LC1 = r6; |
| |
| /* |
| * Clear ITEST_COMMAND and DTEST_COMMAND registers, |
| * Leaving these as non-zero can confuse the emulator |
| */ |
| [p5 + (DTEST_COMMAND - COREMMR_BASE)] = r6; |
| [p5 + (ITEST_COMMAND - COREMMR_BASE)] = r6; |
| CSYNC; |
| |
| trace_buffer_init(p0,r0); |
| |
| /* Turn off the icache */ |
| r1 = [p5 + (IMEM_CONTROL - COREMMR_BASE)]; |
| BITCLR (r1, ENICPLB_P); |
| [p5 + (IMEM_CONTROL - COREMMR_BASE)] = r1; |
| SSYNC; |
| |
| /* Turn off the dcache */ |
| r1 = [p5 + (DMEM_CONTROL - COREMMR_BASE)]; |
| BITCLR (r1, ENDCPLB_P); |
| [p5 + (DMEM_CONTROL - COREMMR_BASE)] = r1; |
| SSYNC; |
| |
| /* in case of double faults, save a few things */ |
| p0.l = _init_retx; |
| p0.h = _init_retx; |
| R0 = RETX; |
| [P0] = R0; |
| |
| #ifdef CONFIG_DEBUG_DOUBLEFAULT |
| /* Only save these if we are storing them, |
| * This happens here, since L1 gets clobbered |
| * below |
| */ |
| GET_PDA(p0, r0); |
| r5 = [p0 + PDA_DF_RETX]; |
| p1.l = _init_saved_retx; |
| p1.h = _init_saved_retx; |
| [p1] = r5; |
| |
| r5 = [p0 + PDA_DF_DCPLB]; |
| p1.l = _init_saved_dcplb_fault_addr; |
| p1.h = _init_saved_dcplb_fault_addr; |
| [p1] = r5; |
| |
| r5 = [p0 + PDA_DF_ICPLB]; |
| p1.l = _init_saved_icplb_fault_addr; |
| p1.h = _init_saved_icplb_fault_addr; |
| [p1] = r5; |
| |
| r5 = [p0 + PDA_DF_SEQSTAT]; |
| p1.l = _init_saved_seqstat; |
| p1.h = _init_saved_seqstat; |
| [p1] = r5; |
| #endif |
| |
| /* Initialize stack pointer */ |
| sp.l = _init_thread_union + THREAD_SIZE; |
| sp.h = _init_thread_union + THREAD_SIZE; |
| fp = sp; |
| usp = sp; |
| |
| #ifdef CONFIG_EARLY_PRINTK |
| call _init_early_exception_vectors; |
| r0 = (EVT_IVHW | EVT_IRPTEN | EVT_EVX | EVT_NMI | EVT_RST | EVT_EMU); |
| sti r0; |
| #endif |
| |
| r0 = r6; |
| /* Zero out all of the fun bss regions */ |
| #if L1_DATA_A_LENGTH > 0 |
| r1.l = __sbss_l1; |
| r1.h = __sbss_l1; |
| r2.l = __ebss_l1; |
| r2.h = __ebss_l1; |
| call __init_clear_bss |
| #endif |
| #if L1_DATA_B_LENGTH > 0 |
| r1.l = __sbss_b_l1; |
| r1.h = __sbss_b_l1; |
| r2.l = __ebss_b_l1; |
| r2.h = __ebss_b_l1; |
| call __init_clear_bss |
| #endif |
| #if L2_LENGTH > 0 |
| r1.l = __sbss_l2; |
| r1.h = __sbss_l2; |
| r2.l = __ebss_l2; |
| r2.h = __ebss_l2; |
| call __init_clear_bss |
| #endif |
| r1.l = ___bss_start; |
| r1.h = ___bss_start; |
| r2.l = ___bss_stop; |
| r2.h = ___bss_stop; |
| call __init_clear_bss |
| |
| /* Put The Code for PLL Programming and SDRAM Programming in L1 ISRAM */ |
| call _bfin_relocate_l1_mem; |
| |
| #ifdef CONFIG_ROMKERNEL |
| call _bfin_relocate_xip_data; |
| #endif |
| |
| #ifdef CONFIG_BFIN_KERNEL_CLOCK |
| /* Only use on-chip scratch space for stack when absolutely required |
| * to avoid Anomaly 05000227 ... we know the init_clocks() func only |
| * uses L1 text and stack space and no other memory region. |
| */ |
| # define KERNEL_CLOCK_STACK (L1_SCRATCH_START + L1_SCRATCH_LENGTH - 12) |
| sp.l = lo(KERNEL_CLOCK_STACK); |
| sp.h = hi(KERNEL_CLOCK_STACK); |
| call _init_clocks; |
| sp = usp; /* usp hasn't been touched, so restore from there */ |
| #endif |
| |
| /* This section keeps the processor in supervisor mode |
| * during kernel boot. Switches to user mode at end of boot. |
| * See page 3-9 of Hardware Reference manual for documentation. |
| */ |
| |
| /* EVT15 = _real_start */ |
| |
| p1.l = _real_start; |
| p1.h = _real_start; |
| [p5 + (EVT15 - COREMMR_BASE)] = p1; |
| csync; |
| |
| #ifdef CONFIG_EARLY_PRINTK |
| r0 = (EVT_IVG15 | EVT_IVHW | EVT_IRPTEN | EVT_EVX | EVT_NMI | EVT_RST | EVT_EMU) (z); |
| #else |
| r0 = EVT_IVG15 (z); |
| #endif |
| sti r0; |
| |
| raise 15; |
| #ifdef CONFIG_EARLY_PRINTK |
| p0.l = _early_trap; |
| p0.h = _early_trap; |
| #else |
| p0.l = .LWAIT_HERE; |
| p0.h = .LWAIT_HERE; |
| #endif |
| reti = p0; |
| #if ANOMALY_05000281 |
| nop; nop; nop; |
| #endif |
| rti; |
| |
| .LWAIT_HERE: |
| jump .LWAIT_HERE; |
| ENDPROC(__start) |
| |
| /* A little BF561 glue ... */ |
| #ifndef WDOG_CTL |
| # define WDOG_CTL WDOGA_CTL |
| #endif |
| |
| ENTRY(_real_start) |
| /* Enable nested interrupts */ |
| [--sp] = reti; |
| |
| /* watchdog off for now */ |
| p0.l = lo(WDOG_CTL); |
| p0.h = hi(WDOG_CTL); |
| r0 = 0xAD6(z); |
| w[p0] = r0; |
| ssync; |
| |
| /* Pass the u-boot arguments to the global value command line */ |
| R0 = R7; |
| call _cmdline_init; |
| |
| sp += -12 + 4; /* +4 is for reti loading above */ |
| call _init_pda |
| sp += 12; |
| jump.l _start_kernel; |
| ENDPROC(_real_start) |
| |
| __FINIT |