OMAP3: remove OPP interfaces from OMAP PM layer

With new OPP layer, OPP users will access OPP API directly instead of
using OMAP PM layer, so remove all notions of OPPs from the OMAP PM
layer.

Acked-by: Paul Walmsley <paul@pwsan.com>

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c
index 4605d50..5577ab2 100644
--- a/arch/arm/mach-omap2/io.c
+++ b/arch/arm/mach-omap2/io.c
@@ -347,8 +347,7 @@
 	else if (cpu_is_omap44xx())
 		omap44xx_hwmod_init();
 
-	/* The OPP tables have to be registered before a clk init */
-	omap_pm_if_early_init(mpu_opps, dsp_opps, l3_opps);
+	omap_pm_if_early_init();
 
 	if (cpu_is_omap2420())
 		omap2420_clk_init();
diff --git a/arch/arm/plat-omap/include/plat/omap-pm.h b/arch/arm/plat-omap/include/plat/omap-pm.h
index 728fbb9..62c3fe9 100644
--- a/arch/arm/plat-omap/include/plat/omap-pm.h
+++ b/arch/arm/plat-omap/include/plat/omap-pm.h
@@ -17,27 +17,10 @@
 #include <linux/device.h>
 #include <linux/cpufreq.h>
 #include <linux/clk.h>
+#include <linux/opp.h>
 
 #include "powerdomain.h"
 
-/**
- * struct omap_opp - clock frequency-to-OPP ID table for DSP, MPU
- * @rate: target clock rate
- * @opp_id: OPP ID
- * @min_vdd: minimum VDD1 voltage (in millivolts) for this OPP
- *
- * Operating performance point data.  Can vary by OMAP chip and board.
- */
-struct omap_opp {
-	unsigned long rate;
-	u8 opp_id;
-	u16 min_vdd;
-};
-
-extern struct omap_opp *mpu_opps;
-extern struct omap_opp *dsp_opps;
-extern struct omap_opp *l3_opps;
-
 /*
  * agent_id values for use with omap_pm_set_min_bus_tput():
  *
@@ -59,9 +42,11 @@
  * framework starts.  The "_if_" is to avoid name collisions with the
  * PM idle-loop code.
  */
-int __init omap_pm_if_early_init(struct omap_opp *mpu_opp_table,
-				 struct omap_opp *dsp_opp_table,
-				 struct omap_opp *l3_opp_table);
+#ifdef CONFIG_OMAP_PM_NONE
+#define omap_pm_if_early_init() 0
+#else
+int __init omap_pm_if_early_init(void);
+#endif
 
 /**
  * omap_pm_if_init - OMAP PM init code called after clock fw init
@@ -69,7 +54,11 @@
  * The main initialization code.  OPP tables are passed in here.  The
  * "_if_" is to avoid name collisions with the PM idle-loop code.
  */
+#ifdef CONFIG_OMAP_PM_NONE
+#define omap_pm_if_init() 0
+#else
 int __init omap_pm_if_init(void);
+#endif
 
 /**
  * omap_pm_if_exit - OMAP PM exit code
diff --git a/arch/arm/plat-omap/omap-pm-noop.c b/arch/arm/plat-omap/omap-pm-noop.c
index e129ce8..ca75abb 100644
--- a/arch/arm/plat-omap/omap-pm-noop.c
+++ b/arch/arm/plat-omap/omap-pm-noop.c
@@ -26,10 +26,6 @@
 
 #include <plat/powerdomain.h>
 
-struct omap_opp *dsp_opps;
-struct omap_opp *mpu_opps;
-struct omap_opp *l3_opps;
-
 /*
  * Device-driver-originated constraints (via board-*.c files)
  */
@@ -308,13 +304,8 @@
 
 
 /* Should be called before clk framework init */
-int __init omap_pm_if_early_init(struct omap_opp *mpu_opp_table,
-				 struct omap_opp *dsp_opp_table,
-				 struct omap_opp *l3_opp_table)
+int __init omap_pm_if_early_init(void)
 {
-	mpu_opps = mpu_opp_table;
-	dsp_opps = dsp_opp_table;
-	l3_opps = l3_opp_table;
 	return 0;
 }