| /**************************************************************************** |
| * Driver for Solarflare Solarstorm network controllers and boards |
| * Copyright 2006-2008 Solarflare Communications Inc. |
| * |
| * This program is free software; you can redistribute it and/or modify it |
| * under the terms of the GNU General Public License version 2 as published |
| * by the Free Software Foundation, incorporated herein by reference. |
| */ |
| /* |
| * Driver for AMCC QT202x SFP+ and XFP adapters; see www.amcc.com for details |
| */ |
| |
| #include <linux/timer.h> |
| #include <linux/delay.h> |
| #include "efx.h" |
| #include "mdio_10g.h" |
| #include "phy.h" |
| #include "falcon.h" |
| |
| #define QT202X_REQUIRED_DEVS (MDIO_DEVS_PCS | \ |
| MDIO_DEVS_PMAPMD | \ |
| MDIO_DEVS_PHYXS) |
| |
| #define QT202X_LOOPBACKS ((1 << LOOPBACK_PCS) | \ |
| (1 << LOOPBACK_PMAPMD) | \ |
| (1 << LOOPBACK_NETWORK)) |
| |
| /****************************************************************************/ |
| /* Quake-specific MDIO registers */ |
| #define MDIO_QUAKE_LED0_REG (0xD006) |
| |
| /* QT2025C only */ |
| #define PCS_FW_HEARTBEAT_REG 0xd7ee |
| #define PCS_FW_HEARTB_LBN 0 |
| #define PCS_FW_HEARTB_WIDTH 8 |
| #define PCS_UC8051_STATUS_REG 0xd7fd |
| #define PCS_UC_STATUS_LBN 0 |
| #define PCS_UC_STATUS_WIDTH 8 |
| #define PCS_UC_STATUS_FW_SAVE 0x20 |
| #define PMA_PMD_FTX_CTRL2_REG 0xc309 |
| #define PMA_PMD_FTX_STATIC_LBN 13 |
| #define PMA_PMD_VEND1_REG 0xc001 |
| #define PMA_PMD_VEND1_LBTXD_LBN 15 |
| #define PCS_VEND1_REG 0xc000 |
| #define PCS_VEND1_LBTXD_LBN 5 |
| |
| void falcon_qt202x_set_led(struct efx_nic *p, int led, int mode) |
| { |
| int addr = MDIO_QUAKE_LED0_REG + led; |
| efx_mdio_write(p, MDIO_MMD_PMAPMD, addr, mode); |
| } |
| |
| struct qt202x_phy_data { |
| enum efx_phy_mode phy_mode; |
| }; |
| |
| #define QT2022C2_MAX_RESET_TIME 500 |
| #define QT2022C2_RESET_WAIT 10 |
| |
| static int qt2025c_wait_reset(struct efx_nic *efx) |
| { |
| unsigned long timeout = jiffies + 10 * HZ; |
| int reg, old_counter = 0; |
| |
| /* Wait for firmware heartbeat to start */ |
| for (;;) { |
| int counter; |
| reg = efx_mdio_read(efx, MDIO_MMD_PCS, PCS_FW_HEARTBEAT_REG); |
| if (reg < 0) |
| return reg; |
| counter = ((reg >> PCS_FW_HEARTB_LBN) & |
| ((1 << PCS_FW_HEARTB_WIDTH) - 1)); |
| if (old_counter == 0) |
| old_counter = counter; |
| else if (counter != old_counter) |
| break; |
| if (time_after(jiffies, timeout)) |
| return -ETIMEDOUT; |
| msleep(10); |
| } |
| |
| /* Wait for firmware status to look good */ |
| for (;;) { |
| reg = efx_mdio_read(efx, MDIO_MMD_PCS, PCS_UC8051_STATUS_REG); |
| if (reg < 0) |
| return reg; |
| if ((reg & |
| ((1 << PCS_UC_STATUS_WIDTH) - 1) << PCS_UC_STATUS_LBN) >= |
| PCS_UC_STATUS_FW_SAVE) |
| break; |
| if (time_after(jiffies, timeout)) |
| return -ETIMEDOUT; |
| msleep(100); |
| } |
| |
| return 0; |
| } |
| |
| static int qt202x_reset_phy(struct efx_nic *efx) |
| { |
| int rc; |
| |
| if (efx->phy_type == PHY_TYPE_QT2025C) { |
| /* Wait for the reset triggered by falcon_reset_hw() |
| * to complete */ |
| rc = qt2025c_wait_reset(efx); |
| if (rc < 0) |
| goto fail; |
| } else { |
| /* Reset the PHYXS MMD. This is documented as doing |
| * a complete soft reset. */ |
| rc = efx_mdio_reset_mmd(efx, MDIO_MMD_PHYXS, |
| QT2022C2_MAX_RESET_TIME / |
| QT2022C2_RESET_WAIT, |
| QT2022C2_RESET_WAIT); |
| if (rc < 0) |
| goto fail; |
| } |
| |
| /* Wait 250ms for the PHY to complete bootup */ |
| msleep(250); |
| |
| /* Check that all the MMDs we expect are present and responding. We |
| * expect faults on some if the link is down, but not on the PHY XS */ |
| rc = efx_mdio_check_mmds(efx, QT202X_REQUIRED_DEVS, MDIO_DEVS_PHYXS); |
| if (rc < 0) |
| goto fail; |
| |
| falcon_board(efx)->type->init_phy(efx); |
| |
| return rc; |
| |
| fail: |
| EFX_ERR(efx, "PHY reset timed out\n"); |
| return rc; |
| } |
| |
| static int qt202x_phy_init(struct efx_nic *efx) |
| { |
| struct qt202x_phy_data *phy_data; |
| u32 devid; |
| int rc; |
| |
| rc = qt202x_reset_phy(efx); |
| if (rc) { |
| EFX_ERR(efx, "PHY init failed\n"); |
| return rc; |
| } |
| |
| phy_data = kzalloc(sizeof(struct qt202x_phy_data), GFP_KERNEL); |
| if (!phy_data) |
| return -ENOMEM; |
| efx->phy_data = phy_data; |
| |
| devid = efx_mdio_read_id(efx, MDIO_MMD_PHYXS); |
| EFX_INFO(efx, "PHY ID reg %x (OUI %06x model %02x revision %x)\n", |
| devid, efx_mdio_id_oui(devid), efx_mdio_id_model(devid), |
| efx_mdio_id_rev(devid)); |
| |
| phy_data->phy_mode = efx->phy_mode; |
| return 0; |
| } |
| |
| static int qt202x_link_ok(struct efx_nic *efx) |
| { |
| return efx_mdio_links_ok(efx, QT202X_REQUIRED_DEVS); |
| } |
| |
| static bool qt202x_phy_poll(struct efx_nic *efx) |
| { |
| bool was_up = efx->link_state.up; |
| |
| efx->link_state.up = qt202x_link_ok(efx); |
| efx->link_state.speed = 10000; |
| efx->link_state.fd = true; |
| efx->link_state.fc = efx->wanted_fc; |
| |
| return efx->link_state.up != was_up; |
| } |
| |
| static int qt202x_phy_reconfigure(struct efx_nic *efx) |
| { |
| struct qt202x_phy_data *phy_data = efx->phy_data; |
| |
| if (efx->phy_type == PHY_TYPE_QT2025C) { |
| /* There are several different register bits which can |
| * disable TX (and save power) on direct-attach cables |
| * or optical transceivers, varying somewhat between |
| * firmware versions. Only 'static mode' appears to |
| * cover everything. */ |
| mdio_set_flag( |
| &efx->mdio, efx->mdio.prtad, MDIO_MMD_PMAPMD, |
| PMA_PMD_FTX_CTRL2_REG, 1 << PMA_PMD_FTX_STATIC_LBN, |
| efx->phy_mode & PHY_MODE_TX_DISABLED || |
| efx->phy_mode & PHY_MODE_LOW_POWER || |
| efx->loopback_mode == LOOPBACK_PCS || |
| efx->loopback_mode == LOOPBACK_PMAPMD); |
| } else { |
| /* Reset the PHY when moving from tx off to tx on */ |
| if (!(efx->phy_mode & PHY_MODE_TX_DISABLED) && |
| (phy_data->phy_mode & PHY_MODE_TX_DISABLED)) |
| qt202x_reset_phy(efx); |
| |
| efx_mdio_transmit_disable(efx); |
| } |
| |
| efx_mdio_phy_reconfigure(efx); |
| |
| phy_data->phy_mode = efx->phy_mode; |
| |
| return 0; |
| } |
| |
| static void qt202x_phy_get_settings(struct efx_nic *efx, struct ethtool_cmd *ecmd) |
| { |
| mdio45_ethtool_gset(&efx->mdio, ecmd); |
| } |
| |
| static void qt202x_phy_fini(struct efx_nic *efx) |
| { |
| /* Free the context block */ |
| kfree(efx->phy_data); |
| efx->phy_data = NULL; |
| } |
| |
| struct efx_phy_operations falcon_qt202x_phy_ops = { |
| .macs = EFX_XMAC, |
| .init = qt202x_phy_init, |
| .reconfigure = qt202x_phy_reconfigure, |
| .poll = qt202x_phy_poll, |
| .fini = qt202x_phy_fini, |
| .get_settings = qt202x_phy_get_settings, |
| .set_settings = efx_mdio_set_settings, |
| .mmds = QT202X_REQUIRED_DEVS, |
| .loopbacks = QT202X_LOOPBACKS, |
| }; |