Merge tag 'omap-devel-b-for-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into for_3.10/dts_merged
diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts
index f624dc8..02d23f1 100644
--- a/arch/arm/boot/dts/omap3-beagle.dts
+++ b/arch/arm/boot/dts/omap3-beagle.dts
@@ -38,6 +38,57 @@
};
};
+ /* HS USB Port 2 RESET */
+ hsusb2_reset: hsusb2_reset_reg {
+ compatible = "regulator-fixed";
+ regulator-name = "hsusb2_reset";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio5 19 0>; /* gpio_147 */
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
+
+ /* HS USB Port 2 Power */
+ hsusb2_power: hsusb2_power_reg {
+ compatible = "regulator-fixed";
+ regulator-name = "hsusb2_vbus";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&twl_gpio 18 0>; /* GPIO LEDA */
+ startup-delay-us = <70000>;
+ };
+
+ /* HS USB Host PHY on PORT 2 */
+ hsusb2_phy: hsusb2_phy {
+ compatible = "usb-nop-xceiv";
+ reset-supply = <&hsusb2_reset>;
+ vcc-supply = <&hsusb2_power>;
+ };
+};
+
+&omap3_pmx_core {
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &hsusbb2_pins
+ >;
+
+ hsusbb2_pins: pinmux_hsusbb2_pins {
+ pinctrl-single,pins = <
+ 0x5c0 0x3 /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_clk OUTPUT */
+ 0x5c2 0x3 /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_stp OUTPUT */
+ 0x5c4 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dir INPUT | PULLDOWN */
+ 0x5c6 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_nxt INPUT | PULLDOWN */
+ 0x5c8 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat0 INPUT | PULLDOWN */
+ 0x5cA 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat1 INPUT | PULLDOWN */
+ 0x1a4 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat2 INPUT | PULLDOWN */
+ 0x1a6 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat3 INPUT | PULLDOWN */
+ 0x1a8 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat4 INPUT | PULLDOWN */
+ 0x1aa 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat5 INPUT | PULLDOWN */
+ 0x1ac 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat6 INPUT | PULLDOWN */
+ 0x1ae 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat7 INPUT | PULLDOWN */
+ >;
+ };
};
&i2c1 {
@@ -65,3 +116,23 @@
&mmc3 {
status = "disabled";
};
+
+&usbhshost {
+ port2-mode = "ehci-phy";
+};
+
+&usbhsehci {
+ phys = <0 &hsusb2_phy>;
+};
+
+&twl_gpio {
+ ti,use-leds;
+ /* pullups: BIT(1) */
+ ti,pullups = <0x000002>;
+ /*
+ * pulldowns:
+ * BIT(2), BIT(6), BIT(7), BIT(8), BIT(13)
+ * BIT(15), BIT(16), BIT(17)
+ */
+ ti,pulldowns = <0x03a1c4>;
+};
diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi
index 1acc261..a14f74b 100644
--- a/arch/arm/boot/dts/omap3.dtsi
+++ b/arch/arm/boot/dts/omap3.dtsi
@@ -397,5 +397,36 @@
ti,timer-alwon;
ti,timer-secure;
};
+
+ usbhstll: usbhstll@48062000 {
+ compatible = "ti,usbhs-tll";
+ reg = <0x48062000 0x1000>;
+ interrupts = <78>;
+ ti,hwmods = "usb_tll_hs";
+ };
+
+ usbhshost: usbhshost@48064000 {
+ compatible = "ti,usbhs-host";
+ reg = <0x48064000 0x400>;
+ ti,hwmods = "usb_host_hs";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ usbhsohci: ohci@48064400 {
+ compatible = "ti,ohci-omap3", "usb-ohci";
+ reg = <0x48064400 0x400>;
+ interrupt-parent = <&intc>;
+ interrupts = <76>;
+ };
+
+ usbhsehci: ehci@48064800 {
+ compatible = "ti,ehci-omap", "usb-ehci";
+ reg = <0x48064800 0x400>;
+ interrupt-parent = <&intc>;
+ interrupts = <77>;
+ };
+ };
+
};
};
diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
index 739bb79..b7db1a2 100644
--- a/arch/arm/boot/dts/omap4.dtsi
+++ b/arch/arm/boot/dts/omap4.dtsi
@@ -529,5 +529,35 @@
ti,hwmods = "timer11";
ti,timer-pwm;
};
+
+ usbhstll: usbhstll@4a062000 {
+ compatible = "ti,usbhs-tll";
+ reg = <0x4a062000 0x1000>;
+ interrupts = <0 78 0x4>;
+ ti,hwmods = "usb_tll_hs";
+ };
+
+ usbhshost: usbhshost@4a064000 {
+ compatible = "ti,usbhs-host";
+ reg = <0x4a064000 0x800>;
+ ti,hwmods = "usb_host_hs";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ usbhsohci: ohci@4a064800 {
+ compatible = "ti,ohci-omap3", "usb-ohci";
+ reg = <0x4a064800 0x400>;
+ interrupt-parent = <&gic>;
+ interrupts = <0 76 0x4>;
+ };
+
+ usbhsehci: ehci@4a064c00 {
+ compatible = "ti,ehci-omap", "usb-ehci";
+ reg = <0x4a064c00 0x400>;
+ interrupt-parent = <&gic>;
+ interrupts = <0 77 0x4>;
+ };
+ };
};
};
diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c
index ce812de..7eb9651 100644
--- a/arch/arm/mach-omap2/board-3430sdp.c
+++ b/arch/arm/mach-omap2/board-3430sdp.c
@@ -445,16 +445,23 @@
OMAP_WAKEUP_EN | OMAP_PIN_INPUT_PULLUP);
}
+static struct usbhs_phy_data phy_data[] __initdata = {
+ {
+ .port = 1,
+ .reset_gpio = 57,
+ .vcc_gpio = -EINVAL,
+ },
+ {
+ .port = 2,
+ .reset_gpio = 61,
+ .vcc_gpio = -EINVAL,
+ },
+};
+
static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
- .phy_reset = true,
- .reset_gpio_port[0] = 57,
- .reset_gpio_port[1] = 61,
- .reset_gpio_port[2] = -EINVAL
};
#ifdef CONFIG_OMAP_MUX
@@ -606,6 +613,8 @@
board_flash_init(sdp_flash_partitions, chip_sel_3430, 0);
sdp3430_display_init();
enable_board_wakeup_source();
+
+ usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
usbhs_init(&usbhs_bdata);
}
diff --git a/arch/arm/mach-omap2/board-3630sdp.c b/arch/arm/mach-omap2/board-3630sdp.c
index 67447bd..20d6d81 100644
--- a/arch/arm/mach-omap2/board-3630sdp.c
+++ b/arch/arm/mach-omap2/board-3630sdp.c
@@ -53,16 +53,23 @@
OMAP_WAKEUP_EN | OMAP_PIN_INPUT_PULLUP);
}
+static struct usbhs_phy_data phy_data[] __initdata = {
+ {
+ .port = 1,
+ .reset_gpio = 126,
+ .vcc_gpio = -EINVAL,
+ },
+ {
+ .port = 2,
+ .reset_gpio = 61,
+ .vcc_gpio = -EINVAL,
+ },
+};
+
static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
- .phy_reset = true,
- .reset_gpio_port[0] = 126,
- .reset_gpio_port[1] = 61,
- .reset_gpio_port[2] = -EINVAL
};
#ifdef CONFIG_OMAP_MUX
@@ -199,6 +206,8 @@
board_smc91x_init();
board_flash_init(sdp_flash_partitions, chip_sel_sdp, NAND_BUSWIDTH_16);
enable_board_wakeup_source();
+
+ usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
usbhs_init(&usbhs_bdata);
}
diff --git a/arch/arm/mach-omap2/board-am3517crane.c b/arch/arm/mach-omap2/board-am3517crane.c
index 7d3358b..fc53911 100644
--- a/arch/arm/mach-omap2/board-am3517crane.c
+++ b/arch/arm/mach-omap2/board-am3517crane.c
@@ -47,15 +47,17 @@
};
#endif
+static struct usbhs_phy_data phy_data[] __initdata = {
+ {
+ .port = 1,
+ .reset_gpio = GPIO_USB_NRESET,
+ .vcc_gpio = GPIO_USB_POWER,
+ .vcc_polarity = 1,
+ },
+};
+
static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
- .phy_reset = true,
- .reset_gpio_port[0] = GPIO_USB_NRESET,
- .reset_gpio_port[1] = -EINVAL,
- .reset_gpio_port[2] = -EINVAL
};
static struct mtd_partition crane_nand_partitions[] = {
@@ -131,13 +133,7 @@
return;
}
- ret = gpio_request_one(GPIO_USB_POWER, GPIOF_OUT_INIT_HIGH,
- "usb_ehci_enable");
- if (ret < 0) {
- pr_err("Can not request GPIO %d\n", GPIO_USB_POWER);
- return;
- }
-
+ usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
usbhs_init(&usbhs_bdata);
am35xx_emac_init(AM35XX_DEFAULT_MDIO_FREQUENCY, 1);
}
diff --git a/arch/arm/mach-omap2/board-am3517evm.c b/arch/arm/mach-omap2/board-am3517evm.c
index 9fb8590..191f976 100644
--- a/arch/arm/mach-omap2/board-am3517evm.c
+++ b/arch/arm/mach-omap2/board-am3517evm.c
@@ -274,6 +274,14 @@
omap_ctrl_writel(devconf0, OMAP2_CONTROL_DEVCONF0);
}
+static struct usbhs_phy_data phy_data[] __initdata = {
+ {
+ .port = 1,
+ .reset_gpio = 57,
+ .vcc_gpio = -EINVAL,
+ },
+};
+
static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
#if defined(CONFIG_PANEL_SHARP_LQ043T1DG01) || \
@@ -282,12 +290,6 @@
#else
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
#endif
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
- .phy_reset = true,
- .reset_gpio_port[0] = 57,
- .reset_gpio_port[1] = -EINVAL,
- .reset_gpio_port[2] = -EINVAL
};
#ifdef CONFIG_OMAP_MUX
@@ -349,7 +351,6 @@
{} /* Terminator */
};
-
static void __init am3517_evm_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
@@ -361,6 +362,8 @@
/* Configure GPIO for EHCI port */
omap_mux_init_gpio(57, OMAP_PIN_OUTPUT);
+
+ usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
usbhs_init(&usbhs_bdata);
am3517_evm_hecc_init(&am3517_evm_hecc_pdata);
/* DSS */
diff --git a/arch/arm/mach-omap2/board-cm-t35.c b/arch/arm/mach-omap2/board-cm-t35.c
index af2bb21..7fda3f5 100644
--- a/arch/arm/mach-omap2/board-cm-t35.c
+++ b/arch/arm/mach-omap2/board-cm-t35.c
@@ -419,15 +419,22 @@
{} /* Terminator */
};
+static struct usbhs_phy_data phy_data[] __initdata = {
+ {
+ .port = 1,
+ .reset_gpio = OMAP_MAX_GPIO_LINES + 6,
+ .vcc_gpio = -EINVAL,
+ },
+ {
+ .port = 2,
+ .reset_gpio = OMAP_MAX_GPIO_LINES + 7,
+ .vcc_gpio = -EINVAL,
+ },
+};
+
static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
- .phy_reset = true,
- .reset_gpio_port[0] = OMAP_MAX_GPIO_LINES + 6,
- .reset_gpio_port[1] = OMAP_MAX_GPIO_LINES + 7,
- .reset_gpio_port[2] = -EINVAL
};
static void __init cm_t35_init_usbh(void)
@@ -444,6 +451,7 @@
msleep(1);
}
+ usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
usbhs_init(&usbhs_bdata);
}
diff --git a/arch/arm/mach-omap2/board-cm-t3517.c b/arch/arm/mach-omap2/board-cm-t3517.c
index a66da80..6920f6cf 100644
--- a/arch/arm/mach-omap2/board-cm-t3517.c
+++ b/arch/arm/mach-omap2/board-cm-t3517.c
@@ -188,15 +188,22 @@
#define HSUSB2_RESET_GPIO (147)
#define USB_HUB_RESET_GPIO (152)
+static struct usbhs_phy_data phy_data[] __initdata = {
+ {
+ .port = 1,
+ .reset_gpio = HSUSB1_RESET_GPIO,
+ .vcc_gpio = -EINVAL,
+ },
+ {
+ .port = 2,
+ .reset_gpio = HSUSB2_RESET_GPIO,
+ .vcc_gpio = -EINVAL,
+ },
+};
+
static struct usbhs_omap_platform_data cm_t3517_ehci_pdata __initdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
- .phy_reset = true,
- .reset_gpio_port[0] = HSUSB1_RESET_GPIO,
- .reset_gpio_port[1] = HSUSB2_RESET_GPIO,
- .reset_gpio_port[2] = -EINVAL,
};
static int __init cm_t3517_init_usbh(void)
@@ -213,6 +220,7 @@
msleep(1);
}
+ usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
usbhs_init(&cm_t3517_ehci_pdata);
return 0;
diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 53056c3..42fbf1e 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -437,15 +437,7 @@
};
static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
-
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
- .phy_reset = true,
- .reset_gpio_port[0] = -EINVAL,
- .reset_gpio_port[1] = -EINVAL,
- .reset_gpio_port[2] = -EINVAL
};
#ifdef CONFIG_OMAP_MUX
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
index bf92678..95ccec0 100644
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ b/arch/arm/mach-omap2/board-igep0020.c
@@ -527,26 +527,28 @@
omap3_pmic_init("twl4030", &igep_twldata);
}
+static struct usbhs_phy_data igep2_phy_data[] __initdata = {
+ {
+ .port = 1,
+ .reset_gpio = IGEP2_GPIO_USBH_NRESET,
+ .vcc_gpio = -EINVAL,
+ },
+};
+
+static struct usbhs_phy_data igep3_phy_data[] __initdata = {
+ {
+ .port = 2,
+ .reset_gpio = IGEP3_GPIO_USBH_NRESET,
+ .vcc_gpio = -EINVAL,
+ },
+};
+
static struct usbhs_omap_platform_data igep2_usbhs_bdata __initdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
- .phy_reset = true,
- .reset_gpio_port[0] = IGEP2_GPIO_USBH_NRESET,
- .reset_gpio_port[1] = -EINVAL,
- .reset_gpio_port[2] = -EINVAL,
};
static struct usbhs_omap_platform_data igep3_usbhs_bdata __initdata = {
- .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
- .phy_reset = true,
- .reset_gpio_port[0] = -EINVAL,
- .reset_gpio_port[1] = IGEP3_GPIO_USBH_NRESET,
- .reset_gpio_port[2] = -EINVAL,
};
#ifdef CONFIG_OMAP_MUX
@@ -642,8 +644,10 @@
if (machine_is_igep0020()) {
omap_display_init(&igep2_dss_data);
igep2_init_smsc911x();
+ usbhs_init_phys(igep2_phy_data, ARRAY_SIZE(igep2_phy_data));
usbhs_init(&igep2_usbhs_bdata);
} else {
+ usbhs_init_phys(igep3_phy_data, ARRAY_SIZE(igep3_phy_data));
usbhs_init(&igep3_usbhs_bdata);
}
}
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
index c3558f9..5382215 100644
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ b/arch/arm/mach-omap2/board-omap3beagle.c
@@ -33,6 +33,7 @@
#include <linux/mtd/nand.h>
#include <linux/mmc/host.h>
#include <linux/usb/phy.h>
+#include <linux/usb/nop-usb-xceiv.h>
#include <linux/regulator/machine.h>
#include <linux/i2c/twl.h>
@@ -277,6 +278,21 @@
static struct gpio_led gpio_leds[];
+/* PHY's VCC regulator might be added later, so flag that we need it */
+static struct nop_usb_xceiv_platform_data hsusb2_phy_data = {
+ .needs_vcc = true,
+};
+
+static struct usbhs_phy_data phy_data[] = {
+ {
+ .port = 2,
+ .reset_gpio = 147,
+ .vcc_gpio = -1, /* updated in beagle_twl_gpio_setup */
+ .vcc_polarity = 1, /* updated in beagle_twl_gpio_setup */
+ .platform_data = &hsusb2_phy_data,
+ },
+};
+
static int beagle_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
@@ -318,9 +334,11 @@
}
dvi_panel.power_down_gpio = beagle_config.dvi_pd_gpio;
- gpio_request_one(gpio + TWL4030_GPIO_MAX, beagle_config.usb_pwr_level,
- "nEN_USB_PWR");
+ /* TWL4030_GPIO_MAX i.e. LED_GPO controls HS USB Port 2 power */
+ phy_data[0].vcc_gpio = gpio + TWL4030_GPIO_MAX;
+ phy_data[0].vcc_polarity = beagle_config.usb_pwr_level;
+ usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
return 0;
}
@@ -453,15 +471,7 @@
};
static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
-
- .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
- .phy_reset = true,
- .reset_gpio_port[0] = -EINVAL,
- .reset_gpio_port[1] = 147,
- .reset_gpio_port[2] = -EINVAL
};
#ifdef CONFIG_OMAP_MUX
@@ -543,7 +553,9 @@
usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
usb_musb_init(NULL);
+
usbhs_init(&usbhs_bdata);
+
board_nand_init(omap3beagle_nand_partitions,
ARRAY_SIZE(omap3beagle_nand_partitions), NAND_CS,
NAND_BUSWIDTH_16, NULL);
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index 48789e0..2de92fa 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -496,7 +496,7 @@
static struct regulator_consumer_supply omap3evm_vaux2_supplies[] = {
REGULATOR_SUPPLY("VDD_CSIPHY1", "omap3isp"), /* OMAP ISP */
REGULATOR_SUPPLY("VDD_CSIPHY2", "omap3isp"), /* OMAP ISP */
- REGULATOR_SUPPLY("hsusb1", "ehci-omap.0"),
+ REGULATOR_SUPPLY("vcc", "nop_usb_xceiv.2"), /* hsusb port 2 */
REGULATOR_SUPPLY("vaux2", NULL),
};
@@ -539,17 +539,16 @@
return 0;
}
+static struct usbhs_phy_data phy_data[] __initdata = {
+ {
+ .port = 2,
+ .reset_gpio = -1, /* set at runtime */
+ .vcc_gpio = -EINVAL,
+ },
+};
+
static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
-
- .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
- .phy_reset = true,
- /* PHY reset GPIO will be runtime programmed based on EVM version */
- .reset_gpio_port[0] = -EINVAL,
- .reset_gpio_port[1] = -EINVAL,
- .reset_gpio_port[2] = -EINVAL
};
#ifdef CONFIG_OMAP_MUX
@@ -725,7 +724,7 @@
/* setup EHCI phy reset config */
omap_mux_init_gpio(21, OMAP_PIN_INPUT_PULLUP);
- usbhs_bdata.reset_gpio_port[1] = 21;
+ phy_data[0].reset_gpio = 21;
/* EVM REV >= E can supply 500mA with EXTVBUS programming */
musb_board_data.power = 500;
@@ -733,10 +732,12 @@
} else {
/* setup EHCI phy reset on MDC */
omap_mux_init_gpio(135, OMAP_PIN_OUTPUT);
- usbhs_bdata.reset_gpio_port[1] = 135;
+ phy_data[0].reset_gpio = 135;
}
usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
usb_musb_init(&musb_board_data);
+
+ usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
usbhs_init(&usbhs_bdata);
board_nand_init(omap3evm_nand_partitions,
ARRAY_SIZE(omap3evm_nand_partitions), NAND_CS,
diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c
index 2bba362..1004d2a 100644
--- a/arch/arm/mach-omap2/board-omap3pandora.c
+++ b/arch/arm/mach-omap2/board-omap3pandora.c
@@ -346,7 +346,7 @@
};
static struct regulator_consumer_supply pandora_usb_phy_supply[] = {
- REGULATOR_SUPPLY("hsusb1", "ehci-omap.0"),
+ REGULATOR_SUPPLY("vcc", "nop_usb_xceiv.2"), /* hsusb port 2 */
};
/* ads7846 on SPI and 2 nub controllers on I2C */
@@ -561,6 +561,14 @@
printk(KERN_ERR "wl1251 board initialisation failed\n");
}
+static struct usbhs_phy_data phy_data[] __initdata = {
+ {
+ .port = 2,
+ .reset_gpio = 16,
+ .vcc_gpio = -EINVAL,
+ },
+};
+
static struct platform_device *omap3pandora_devices[] __initdata = {
&pandora_leds_gpio,
&pandora_keys_gpio,
@@ -569,15 +577,7 @@
};
static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
-
- .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
- .phy_reset = true,
- .reset_gpio_port[0] = -EINVAL,
- .reset_gpio_port[1] = 16,
- .reset_gpio_port[2] = -EINVAL
};
#ifdef CONFIG_OMAP_MUX
@@ -601,7 +601,10 @@
spi_register_board_info(omap3pandora_spi_board_info,
ARRAY_SIZE(omap3pandora_spi_board_info));
omap_ads7846_init(1, OMAP3_PANDORA_TS_GPIO, 0, NULL);
+
+ usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
usbhs_init(&usbhs_bdata);
+
usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
usb_musb_init(NULL);
gpmc_nand_init(&pandora_nand_data, NULL);
diff --git a/arch/arm/mach-omap2/board-omap3stalker.c b/arch/arm/mach-omap2/board-omap3stalker.c
index 95c10b3..bf09564 100644
--- a/arch/arm/mach-omap2/board-omap3stalker.c
+++ b/arch/arm/mach-omap2/board-omap3stalker.c
@@ -358,19 +358,20 @@
#define OMAP3_STALKER_TS_GPIO 175
+static struct usbhs_phy_data phy_data[] __initdata = {
+ {
+ .port = 2,
+ .reset_gpio = 21,
+ .vcc_gpio = -EINVAL,
+ },
+};
+
static struct platform_device *omap3_stalker_devices[] __initdata = {
&keys_gpio,
};
static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
- .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
- .phy_reset = true,
- .reset_gpio_port[0] = -EINVAL,
- .reset_gpio_port[1] = 21,
- .reset_gpio_port[2] = -EINVAL,
};
#ifdef CONFIG_OMAP_MUX
@@ -407,6 +408,8 @@
omap_sdrc_init(mt46h32m32lf6_sdrc_params, NULL);
usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
usb_musb_init(NULL);
+
+ usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
usbhs_init(&usbhs_bdata);
omap_ads7846_init(1, OMAP3_STALKER_TS_GPIO, 310, NULL);
diff --git a/arch/arm/mach-omap2/board-omap3touchbook.c b/arch/arm/mach-omap2/board-omap3touchbook.c
index bcd44fb..7da48bc 100644
--- a/arch/arm/mach-omap2/board-omap3touchbook.c
+++ b/arch/arm/mach-omap2/board-omap3touchbook.c
@@ -305,21 +305,22 @@
};
#endif
+static struct usbhs_phy_data phy_data[] __initdata = {
+ {
+ .port = 2,
+ .reset_gpio = 147,
+ .vcc_gpio = -EINVAL,
+ },
+};
+
static struct platform_device *omap3_touchbook_devices[] __initdata = {
&leds_gpio,
&keys_gpio,
};
static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
-
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
- .phy_reset = true,
- .reset_gpio_port[0] = -EINVAL,
- .reset_gpio_port[1] = 147,
- .reset_gpio_port[2] = -EINVAL
};
static void omap3_touchbook_poweroff(void)
@@ -368,6 +369,8 @@
omap_ads7846_init(4, OMAP3_TS_GPIO, 310, &ads7846_pdata);
usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
usb_musb_init(NULL);
+
+ usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
usbhs_init(&usbhs_bdata);
board_nand_init(omap3touchbook_nand_partitions,
ARRAY_SIZE(omap3touchbook_nand_partitions), NAND_CS,
diff --git a/arch/arm/mach-omap2/board-omap4panda.c b/arch/arm/mach-omap2/board-omap4panda.c
index b02c2f0..a71ad34 100644
--- a/arch/arm/mach-omap2/board-omap4panda.c
+++ b/arch/arm/mach-omap2/board-omap4panda.c
@@ -31,6 +31,7 @@
#include <linux/ti_wilink_st.h>
#include <linux/usb/musb.h>
#include <linux/usb/phy.h>
+#include <linux/usb/nop-usb-xceiv.h>
#include <linux/wl12xx.h>
#include <linux/irqchip/arm-gic.h>
#include <linux/platform_data/omap-abe-twl6040.h>
@@ -132,6 +133,22 @@
.id = -1,
};
+/* PHY device on HS USB Port 1 i.e. nop_usb_xceiv.1 */
+static struct nop_usb_xceiv_platform_data hsusb1_phy_data = {
+ /* FREF_CLK3 provides the 19.2 MHz reference clock to the PHY */
+ .clk_rate = 19200000,
+};
+
+static struct usbhs_phy_data phy_data[] __initdata = {
+ {
+ .port = 1,
+ .reset_gpio = GPIO_HUB_NRESET,
+ .vcc_gpio = GPIO_HUB_POWER,
+ .vcc_polarity = 1,
+ .platform_data = &hsusb1_phy_data,
+ },
+};
+
static struct platform_device *panda_devices[] __initdata = {
&leds_gpio,
&wl1271_device,
@@ -142,49 +159,19 @@
static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
- .phy_reset = false,
- .reset_gpio_port[0] = -EINVAL,
- .reset_gpio_port[1] = -EINVAL,
- .reset_gpio_port[2] = -EINVAL
-};
-
-static struct gpio panda_ehci_gpios[] __initdata = {
- { GPIO_HUB_POWER, GPIOF_OUT_INIT_LOW, "hub_power" },
- { GPIO_HUB_NRESET, GPIOF_OUT_INIT_LOW, "hub_nreset" },
};
static void __init omap4_ehci_init(void)
{
int ret;
- struct clk *phy_ref_clk;
/* FREF_CLK3 provides the 19.2 MHz reference clock to the PHY */
- phy_ref_clk = clk_get(NULL, "auxclk3_ck");
- if (IS_ERR(phy_ref_clk)) {
- pr_err("Cannot request auxclk3\n");
- return;
- }
- clk_set_rate(phy_ref_clk, 19200000);
- clk_prepare_enable(phy_ref_clk);
+ ret = clk_add_alias("main_clk", "nop_usb_xceiv.1", "auxclk3_ck", NULL);
+ if (ret)
+ pr_err("Failed to add main_clk alias to auxclk3_ck\n");
- /* disable the power to the usb hub prior to init and reset phy+hub */
- ret = gpio_request_array(panda_ehci_gpios,
- ARRAY_SIZE(panda_ehci_gpios));
- if (ret) {
- pr_err("Unable to initialize EHCI power/reset\n");
- return;
- }
-
- gpio_export(GPIO_HUB_POWER, 0);
- gpio_export(GPIO_HUB_NRESET, 0);
- gpio_set_value(GPIO_HUB_NRESET, 1);
-
+ usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
usbhs_init(&usbhs_bdata);
-
- /* enable power to hub */
- gpio_set_value(GPIO_HUB_POWER, 1);
}
static struct omap_musb_board_data musb_board_data = {
diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c
index 86bab51..ab79a44 100644
--- a/arch/arm/mach-omap2/board-overo.c
+++ b/arch/arm/mach-omap2/board-overo.c
@@ -458,14 +458,16 @@
return 0;
}
+static struct usbhs_phy_data phy_data[] __initdata = {
+ {
+ .port = 2,
+ .reset_gpio = OVERO_GPIO_USBH_NRESET,
+ .vcc_gpio = -EINVAL,
+ },
+};
+
static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
- .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
- .phy_reset = true,
- .reset_gpio_port[0] = -EINVAL,
- .reset_gpio_port[1] = OVERO_GPIO_USBH_NRESET,
- .reset_gpio_port[2] = -EINVAL
};
#ifdef CONFIG_OMAP_MUX
@@ -502,6 +504,8 @@
ARRAY_SIZE(overo_nand_partitions), NAND_CS, 0, NULL);
usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
usb_musb_init(NULL);
+
+ usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
usbhs_init(&usbhs_bdata);
overo_spi_init();
overo_init_smsc911x();
diff --git a/arch/arm/mach-omap2/board-zoom.c b/arch/arm/mach-omap2/board-zoom.c
index 5e4d4c9..1a3dd86 100644
--- a/arch/arm/mach-omap2/board-zoom.c
+++ b/arch/arm/mach-omap2/board-zoom.c
@@ -92,14 +92,16 @@
},
};
+static struct usbhs_phy_data phy_data[] __initdata = {
+ {
+ .port = 2,
+ .reset_gpio = ZOOM3_EHCI_RESET_GPIO,
+ .vcc_gpio = -EINVAL,
+ },
+};
+
static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
- .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
- .phy_reset = true,
- .reset_gpio_port[0] = -EINVAL,
- .reset_gpio_port[1] = ZOOM3_EHCI_RESET_GPIO,
- .reset_gpio_port[2] = -EINVAL,
};
static void __init omap_zoom_init(void)
@@ -109,6 +111,8 @@
} else if (machine_is_omap_zoom3()) {
omap3_mux_init(board_mux, OMAP_PACKAGE_CBP);
omap_mux_init_gpio(ZOOM3_EHCI_RESET_GPIO, OMAP_PIN_OUTPUT);
+
+ usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
usbhs_init(&usbhs_bdata);
}
diff --git a/arch/arm/mach-omap2/usb-host.c b/arch/arm/mach-omap2/usb-host.c
index 5706bdc..aa27d7f 100644
--- a/arch/arm/mach-omap2/usb-host.c
+++ b/arch/arm/mach-omap2/usb-host.c
@@ -22,8 +22,12 @@
#include <linux/platform_device.h>
#include <linux/slab.h>
#include <linux/dma-mapping.h>
-
-#include <asm/io.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/fixed.h>
+#include <linux/string.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+#include <linux/usb/phy.h>
#include "soc.h"
#include "omap_device.h"
@@ -526,3 +530,155 @@
}
#endif
+
+/* Template for PHY regulators */
+static struct fixed_voltage_config hsusb_reg_config = {
+ /* .supply_name filled later */
+ .microvolts = 3300000,
+ .gpio = -1, /* updated later */
+ .startup_delay = 70000, /* 70msec */
+ .enable_high = 1, /* updated later */
+ .enabled_at_boot = 0, /* keep in RESET */
+ /* .init_data filled later */
+};
+
+static const char *nop_name = "nop_usb_xceiv"; /* NOP PHY driver */
+static const char *reg_name = "reg-fixed-voltage"; /* Regulator driver */
+
+/**
+ * usbhs_add_regulator - Add a gpio based fixed voltage regulator device
+ * @name: name for the regulator
+ * @dev_id: device id of the device this regulator supplies power to
+ * @dev_supply: supply name that the device expects
+ * @gpio: GPIO number
+ * @polarity: 1 - Active high, 0 - Active low
+ */
+static int usbhs_add_regulator(char *name, char *dev_id, char *dev_supply,
+ int gpio, int polarity)
+{
+ struct regulator_consumer_supply *supplies;
+ struct regulator_init_data *reg_data;
+ struct fixed_voltage_config *config;
+ struct platform_device *pdev;
+ int ret;
+
+ supplies = kzalloc(sizeof(*supplies), GFP_KERNEL);
+ if (!supplies)
+ return -ENOMEM;
+
+ supplies->supply = dev_supply;
+ supplies->dev_name = dev_id;
+
+ reg_data = kzalloc(sizeof(*reg_data), GFP_KERNEL);
+ if (!reg_data)
+ return -ENOMEM;
+
+ reg_data->constraints.valid_ops_mask = REGULATOR_CHANGE_STATUS;
+ reg_data->consumer_supplies = supplies;
+ reg_data->num_consumer_supplies = 1;
+
+ config = kmemdup(&hsusb_reg_config, sizeof(hsusb_reg_config),
+ GFP_KERNEL);
+ if (!config)
+ return -ENOMEM;
+
+ config->supply_name = name;
+ config->gpio = gpio;
+ config->enable_high = polarity;
+ config->init_data = reg_data;
+
+ /* create a regulator device */
+ pdev = kzalloc(sizeof(*pdev), GFP_KERNEL);
+ if (!pdev)
+ return -ENOMEM;
+
+ pdev->id = PLATFORM_DEVID_AUTO;
+ pdev->name = reg_name;
+ pdev->dev.platform_data = config;
+
+ ret = platform_device_register(pdev);
+ if (ret)
+ pr_err("%s: Failed registering regulator %s for %s\n",
+ __func__, name, dev_id);
+
+ return ret;
+}
+
+int usbhs_init_phys(struct usbhs_phy_data *phy, int num_phys)
+{
+ char *rail_name;
+ int i, len;
+ struct platform_device *pdev;
+ char *phy_id;
+
+ /* the phy_id will be something like "nop_usb_xceiv.1" */
+ len = strlen(nop_name) + 3; /* 3 -> ".1" and NULL terminator */
+
+ for (i = 0; i < num_phys; i++) {
+
+ if (!phy->port) {
+ pr_err("%s: Invalid port 0. Must start from 1\n",
+ __func__);
+ continue;
+ }
+
+ /* do we need a NOP PHY device ? */
+ if (!gpio_is_valid(phy->reset_gpio) &&
+ !gpio_is_valid(phy->vcc_gpio))
+ continue;
+
+ /* create a NOP PHY device */
+ pdev = kzalloc(sizeof(*pdev), GFP_KERNEL);
+ if (!pdev)
+ return -ENOMEM;
+
+ pdev->id = phy->port;
+ pdev->name = nop_name;
+ pdev->dev.platform_data = phy->platform_data;
+
+ phy_id = kmalloc(len, GFP_KERNEL);
+ if (!phy_id)
+ return -ENOMEM;
+
+ scnprintf(phy_id, len, "nop_usb_xceiv.%d\n",
+ pdev->id);
+
+ if (platform_device_register(pdev)) {
+ pr_err("%s: Failed to register device %s\n",
+ __func__, phy_id);
+ continue;
+ }
+
+ usb_bind_phy("ehci-omap.0", phy->port - 1, phy_id);
+
+ /* Do we need RESET regulator ? */
+ if (gpio_is_valid(phy->reset_gpio)) {
+
+ rail_name = kmalloc(13, GFP_KERNEL);
+ if (!rail_name)
+ return -ENOMEM;
+
+ scnprintf(rail_name, 13, "hsusb%d_reset", phy->port);
+
+ usbhs_add_regulator(rail_name, phy_id, "reset",
+ phy->reset_gpio, 1);
+ }
+
+ /* Do we need VCC regulator ? */
+ if (gpio_is_valid(phy->vcc_gpio)) {
+
+ rail_name = kmalloc(13, GFP_KERNEL);
+ if (!rail_name)
+ return -ENOMEM;
+
+ scnprintf(rail_name, 13, "hsusb%d_vcc", phy->port);
+
+ usbhs_add_regulator(rail_name, phy_id, "vcc",
+ phy->vcc_gpio, phy->vcc_polarity);
+ }
+
+ phy++;
+ }
+
+ return 0;
+}
diff --git a/arch/arm/mach-omap2/usb.h b/arch/arm/mach-omap2/usb.h
index 3319f5c..e7261eb 100644
--- a/arch/arm/mach-omap2/usb.h
+++ b/arch/arm/mach-omap2/usb.h
@@ -53,8 +53,17 @@
#define USBPHY_OTGSESSEND_EN (1 << 20)
#define USBPHY_DATA_POLARITY (1 << 23)
+struct usbhs_phy_data {
+ int port; /* 1 indexed port number */
+ int reset_gpio;
+ int vcc_gpio;
+ bool vcc_polarity; /* 1 active high, 0 active low */
+ void *platform_data;
+};
+
extern void usb_musb_init(struct omap_musb_board_data *board_data);
extern void usbhs_init(struct usbhs_omap_platform_data *pdata);
+extern int usbhs_init_phys(struct usbhs_phy_data *phy, int num_phys);
extern void am35x_musb_reset(void);
extern void am35x_musb_phy_power(u8 on);
diff --git a/include/linux/usb/nop-usb-xceiv.h b/include/linux/usb/nop-usb-xceiv.h
index 28884c7..148d351 100644
--- a/include/linux/usb/nop-usb-xceiv.h
+++ b/include/linux/usb/nop-usb-xceiv.h
@@ -5,6 +5,11 @@
struct nop_usb_xceiv_platform_data {
enum usb_phy_type type;
+ unsigned long clk_rate;
+
+ /* if set fails with -EPROBE_DEFER if can't get regulator */
+ unsigned int needs_vcc:1;
+ unsigned int needs_reset:1;
};
#if defined(CONFIG_NOP_USB_XCEIV) || (defined(CONFIG_NOP_USB_XCEIV_MODULE) && defined(MODULE))