omap: Add platform init code for EHCI driver
Add platform init code for EHCI driver.
Various fixes to the original patch by Ajay Kumar Gupta <ajay.gupta@ti.com>
and Anand Gadiyar <gadiyar@ti.com>.
Overo support added by Olof Johansson <olof@lixom.net>
Beagle support added by Koen Kooi <koen@beagleboard.org>
CM-T32 support added by Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Koen Kooi <koen@beagleboard.org>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index 1d54ad3..5c32b650 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -80,6 +80,7 @@
# Platform specific device init code
obj-y += usb-musb.o
obj-$(CONFIG_MACH_OMAP2_TUSB6010) += usb-tusb6010.o
+obj-y += usb-ehci.o
onenand-$(CONFIG_MTD_ONENAND_OMAP2) := gpmc-onenand.o
obj-y += $(onenand-m) $(onenand-y)
diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c
index 4f05298..491364e 100644
--- a/arch/arm/mach-omap2/board-3430sdp.c
+++ b/arch/arm/mach-omap2/board-3430sdp.c
@@ -494,6 +494,18 @@
omap_cfg_reg(AF26_34XX_SYS_NIRQ); /* T2 interrupt line (keypad) */
}
+static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+
+ .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
+ .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
+ .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+
+ .phy_reset = true,
+ .reset_gpio_port[0] = 57,
+ .reset_gpio_port[1] = 61,
+ .reset_gpio_port[2] = -EINVAL
+};
+
static void __init omap_3430sdp_init(void)
{
omap3430_i2c_init();
@@ -510,6 +522,7 @@
usb_musb_init();
board_smc91x_init();
enable_board_wakeup_source();
+ usb_ehci_init(&ehci_pdata);
}
static void __init omap_3430sdp_map_io(void)
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
index 4e69f8e..41480bd 100644
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ b/arch/arm/mach-omap2/board-omap3beagle.c
@@ -410,6 +410,18 @@
}
}
+static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+
+ .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
+ .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
+ .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+
+ .phy_reset = true,
+ .reset_gpio_port[0] = -EINVAL,
+ .reset_gpio_port[1] = 147,
+ .reset_gpio_port[2] = -EINVAL
+};
+
static void __init omap3_beagle_init(void)
{
omap3_beagle_i2c_init();
@@ -423,6 +435,7 @@
gpio_direction_output(170, true);
usb_musb_init();
+ usb_ehci_init(&ehci_pdata);
omap3beagle_flash_init();
/* Ensure SDRC pins are mux'd for self-refresh */
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index e0cac96..1edf06a 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -307,6 +307,18 @@
&omap3evm_smc911x_device,
};
+static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+
+ .port_mode[0] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+ .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
+ .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+
+ .phy_reset = true,
+ .reset_gpio_port[0] = -EINVAL,
+ .reset_gpio_port[1] = 135,
+ .reset_gpio_port[2] = -EINVAL
+};
+
static void __init omap3_evm_init(void)
{
omap3_evm_i2c_init();
@@ -322,6 +334,9 @@
usb_nop_xceiv_register();
#endif
usb_musb_init();
+ /* Setup EHCI phy reset padconfig */
+ omap_cfg_reg(AF4_34XX_GPIO135_OUT);
+ usb_ehci_init(&ehci_pdata);
ads7846_dev_init();
}
diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c
index 3b2e546..2db5ba5 100644
--- a/arch/arm/mach-omap2/board-omap3pandora.c
+++ b/arch/arm/mach-omap2/board-omap3pandora.c
@@ -397,6 +397,18 @@
&pandora_keys_gpio,
};
+static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+
+ .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY,
+ .port_mode[1] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+ .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+
+ .phy_reset = true,
+ .reset_gpio_port[0] = 16,
+ .reset_gpio_port[1] = -EINVAL,
+ .reset_gpio_port[2] = -EINVAL
+};
+
static void __init omap3pandora_init(void)
{
omap3pandora_i2c_init();
@@ -406,6 +418,7 @@
spi_register_board_info(omap3pandora_spi_board_info,
ARRAY_SIZE(omap3pandora_spi_board_info));
omap3pandora_ads7846_init();
+ usb_ehci_init(&ehci_pdata);
pandora_keys_gpio_init();
usb_musb_init();
diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c
index 59d0dfa..52dfd51 100644
--- a/arch/arm/mach-omap2/board-overo.c
+++ b/arch/arm/mach-omap2/board-overo.c
@@ -394,6 +394,18 @@
&overo_lcd_device,
};
+static struct ehci_hcd_omap_platform_data ehci_pdata __initconst = {
+ .port_mode[0] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+ .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
+ .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+
+ .phy_reset = true,
+ .reset_gpio_port[0] = -EINVAL,
+ .reset_gpio_port[1] = OVERO_GPIO_USBH_NRESET,
+ .reset_gpio_port[2] = -EINVAL
+};
+
+
static void __init overo_init(void)
{
overo_i2c_init();
@@ -401,6 +413,7 @@
omap_serial_init();
overo_flash_init();
usb_musb_init();
+ usb_ehci_init(&ehci_pdata);
overo_ads7846_init();
overo_init_smsc911x();
@@ -443,14 +456,6 @@
else
printk(KERN_ERR "could not obtain gpio for "
"OVERO_GPIO_USBH_CPEN\n");
-
- if ((gpio_request(OVERO_GPIO_USBH_NRESET,
- "OVERO_GPIO_USBH_NRESET") == 0) &&
- (gpio_direction_output(OVERO_GPIO_USBH_NRESET, 1) == 0))
- gpio_export(OVERO_GPIO_USBH_NRESET, 0);
- else
- printk(KERN_ERR "could not obtain gpio for "
- "OVERO_GPIO_USBH_NRESET\n");
}
static void __init overo_map_io(void)
diff --git a/arch/arm/mach-omap2/usb-ehci.c b/arch/arm/mach-omap2/usb-ehci.c
new file mode 100644
index 0000000..e448abd
--- /dev/null
+++ b/arch/arm/mach-omap2/usb-ehci.c
@@ -0,0 +1,192 @@
+/*
+ * linux/arch/arm/mach-omap2/usb-ehci.c
+ *
+ * This file will contain the board specific details for the
+ * Synopsys EHCI host controller on OMAP3430
+ *
+ * Copyright (C) 2007 Texas Instruments
+ * Author: Vikram Pandita <vikram.pandita@ti.com>
+ *
+ * Generalization by:
+ * Felipe Balbi <felipe.balbi@nokia.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/types.h>
+#include <linux/errno.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+#include <asm/io.h>
+#include <plat/mux.h>
+
+#include <mach/hardware.h>
+#include <mach/irqs.h>
+#include <plat/usb.h>
+
+#if defined(CONFIG_USB_EHCI_HCD) || defined(CONFIG_USB_EHCI_HCD_MODULE)
+
+static struct resource ehci_resources[] = {
+ {
+ .start = OMAP34XX_EHCI_BASE,
+ .end = OMAP34XX_EHCI_BASE + SZ_1K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = OMAP34XX_UHH_CONFIG_BASE,
+ .end = OMAP34XX_UHH_CONFIG_BASE + SZ_1K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = OMAP34XX_USBTLL_BASE,
+ .end = OMAP34XX_USBTLL_BASE + SZ_4K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ { /* general IRQ */
+ .start = INT_34XX_EHCI_IRQ,
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static u64 ehci_dmamask = ~(u32)0;
+static struct platform_device ehci_device = {
+ .name = "ehci-omap",
+ .id = 0,
+ .dev = {
+ .dma_mask = &ehci_dmamask,
+ .coherent_dma_mask = 0xffffffff,
+ .platform_data = NULL,
+ },
+ .num_resources = ARRAY_SIZE(ehci_resources),
+ .resource = ehci_resources,
+};
+
+/* MUX settings for EHCI pins */
+/*
+ * setup_ehci_io_mux - initialize IO pad mux for USBHOST
+ */
+static void setup_ehci_io_mux(enum ehci_hcd_omap_mode *port_mode)
+{
+ switch (port_mode[0]) {
+ case EHCI_HCD_OMAP_MODE_PHY:
+ omap_cfg_reg(Y9_3430_USB1HS_PHY_STP);
+ omap_cfg_reg(Y8_3430_USB1HS_PHY_CLK);
+ omap_cfg_reg(AA14_3430_USB1HS_PHY_DIR);
+ omap_cfg_reg(AA11_3430_USB1HS_PHY_NXT);
+ omap_cfg_reg(W13_3430_USB1HS_PHY_DATA0);
+ omap_cfg_reg(W12_3430_USB1HS_PHY_DATA1);
+ omap_cfg_reg(W11_3430_USB1HS_PHY_DATA2);
+ omap_cfg_reg(Y11_3430_USB1HS_PHY_DATA3);
+ omap_cfg_reg(W9_3430_USB1HS_PHY_DATA4);
+ omap_cfg_reg(Y12_3430_USB1HS_PHY_DATA5);
+ omap_cfg_reg(W8_3430_USB1HS_PHY_DATA6);
+ omap_cfg_reg(Y13_3430_USB1HS_PHY_DATA7);
+ break;
+ case EHCI_HCD_OMAP_MODE_TLL:
+ omap_cfg_reg(Y9_3430_USB1HS_TLL_STP);
+ omap_cfg_reg(Y8_3430_USB1HS_TLL_CLK);
+ omap_cfg_reg(AA14_3430_USB1HS_TLL_DIR);
+ omap_cfg_reg(AA11_3430_USB1HS_TLL_NXT);
+ omap_cfg_reg(W13_3430_USB1HS_TLL_DATA0);
+ omap_cfg_reg(W12_3430_USB1HS_TLL_DATA1);
+ omap_cfg_reg(W11_3430_USB1HS_TLL_DATA2);
+ omap_cfg_reg(Y11_3430_USB1HS_TLL_DATA3);
+ omap_cfg_reg(W9_3430_USB1HS_TLL_DATA4);
+ omap_cfg_reg(Y12_3430_USB1HS_TLL_DATA5);
+ omap_cfg_reg(W8_3430_USB1HS_TLL_DATA6);
+ omap_cfg_reg(Y13_3430_USB1HS_TLL_DATA7);
+ break;
+ case EHCI_HCD_OMAP_MODE_UNKNOWN:
+ /* FALLTHROUGH */
+ default:
+ break;
+ }
+
+ switch (port_mode[1]) {
+ case EHCI_HCD_OMAP_MODE_PHY:
+ omap_cfg_reg(AA10_3430_USB2HS_PHY_STP);
+ omap_cfg_reg(AA8_3430_USB2HS_PHY_CLK);
+ omap_cfg_reg(AA9_3430_USB2HS_PHY_DIR);
+ omap_cfg_reg(AB11_3430_USB2HS_PHY_NXT);
+ omap_cfg_reg(AB10_3430_USB2HS_PHY_DATA0);
+ omap_cfg_reg(AB9_3430_USB2HS_PHY_DATA1);
+ omap_cfg_reg(W3_3430_USB2HS_PHY_DATA2);
+ omap_cfg_reg(T4_3430_USB2HS_PHY_DATA3);
+ omap_cfg_reg(T3_3430_USB2HS_PHY_DATA4);
+ omap_cfg_reg(R3_3430_USB2HS_PHY_DATA5);
+ omap_cfg_reg(R4_3430_USB2HS_PHY_DATA6);
+ omap_cfg_reg(T2_3430_USB2HS_PHY_DATA7);
+ break;
+ case EHCI_HCD_OMAP_MODE_TLL:
+ omap_cfg_reg(AA10_3430_USB2HS_TLL_STP);
+ omap_cfg_reg(AA8_3430_USB2HS_TLL_CLK);
+ omap_cfg_reg(AA9_3430_USB2HS_TLL_DIR);
+ omap_cfg_reg(AB11_3430_USB2HS_TLL_NXT);
+ omap_cfg_reg(AB10_3430_USB2HS_TLL_DATA0);
+ omap_cfg_reg(AB9_3430_USB2HS_TLL_DATA1);
+ omap_cfg_reg(W3_3430_USB2HS_TLL_DATA2);
+ omap_cfg_reg(T4_3430_USB2HS_TLL_DATA3);
+ omap_cfg_reg(T3_3430_USB2HS_TLL_DATA4);
+ omap_cfg_reg(R3_3430_USB2HS_TLL_DATA5);
+ omap_cfg_reg(R4_3430_USB2HS_TLL_DATA6);
+ omap_cfg_reg(T2_3430_USB2HS_TLL_DATA7);
+ break;
+ case EHCI_HCD_OMAP_MODE_UNKNOWN:
+ /* FALLTHROUGH */
+ default:
+ break;
+ }
+
+ switch (port_mode[2]) {
+ case EHCI_HCD_OMAP_MODE_PHY:
+ printk(KERN_WARNING "Port3 can't be used in PHY mode\n");
+ break;
+ case EHCI_HCD_OMAP_MODE_TLL:
+ omap_cfg_reg(AB3_3430_USB3HS_TLL_STP);
+ omap_cfg_reg(AA6_3430_USB3HS_TLL_CLK);
+ omap_cfg_reg(AA3_3430_USB3HS_TLL_DIR);
+ omap_cfg_reg(Y3_3430_USB3HS_TLL_NXT);
+ omap_cfg_reg(AA5_3430_USB3HS_TLL_DATA0);
+ omap_cfg_reg(Y4_3430_USB3HS_TLL_DATA1);
+ omap_cfg_reg(Y5_3430_USB3HS_TLL_DATA2);
+ omap_cfg_reg(W5_3430_USB3HS_TLL_DATA3);
+ omap_cfg_reg(AB12_3430_USB3HS_TLL_DATA4);
+ omap_cfg_reg(AB13_3430_USB3HS_TLL_DATA5);
+ omap_cfg_reg(AA13_3430_USB3HS_TLL_DATA6);
+ omap_cfg_reg(AA12_3430_USB3HS_TLL_DATA7);
+ break;
+ case EHCI_HCD_OMAP_MODE_UNKNOWN:
+ /* FALLTHROUGH */
+ default:
+ break;
+ }
+
+ return;
+}
+
+void __init usb_ehci_init(struct ehci_hcd_omap_platform_data *pdata)
+{
+ platform_device_add_data(&ehci_device, pdata, sizeof(*pdata));
+
+ /* Setup Pin IO MUX for EHCI */
+ if (cpu_is_omap34xx())
+ setup_ehci_io_mux(pdata->port_mode);
+
+ if (platform_device_register(&ehci_device) < 0) {
+ printk(KERN_ERR "Unable to register HS-USB (EHCI) device\n");
+ return;
+ }
+}
+
+#else
+
+void __init usb_ehci_init(struct ehci_hcd_omap_platform_data *pdata)
+
+{
+}
+
+#endif /* CONFIG_USB_EHCI_HCD */
+
diff --git a/arch/arm/plat-omap/include/plat/omap34xx.h b/arch/arm/plat-omap/include/plat/omap34xx.h
index f8d186a..4655707 100644
--- a/arch/arm/plat-omap/include/plat/omap34xx.h
+++ b/arch/arm/plat-omap/include/plat/omap34xx.h
@@ -74,8 +74,12 @@
#define OMAP34XX_IVA_INTC_BASE 0x40000000
#define OMAP34XX_HSUSB_OTG_BASE (L4_34XX_BASE + 0xAB000)
-#define OMAP34XX_HSUSB_HOST_BASE (L4_34XX_BASE + 0x64000)
#define OMAP34XX_USBTLL_BASE (L4_34XX_BASE + 0x62000)
+#define OMAP34XX_UHH_CONFIG_BASE (L4_34XX_BASE + 0x64000)
+#define OMAP34XX_OHCI_BASE (L4_34XX_BASE + 0x64400)
+#define OMAP34XX_EHCI_BASE (L4_34XX_BASE + 0x64800)
+#define OMAP34XX_SR1_BASE 0x480C9000
+#define OMAP34XX_SR2_BASE 0x480CB000
#define OMAP34XX_MAILBOX_BASE (L4_34XX_BASE + 0x94000)